TABLE OF CONTENTS Elevations/Sizes:1/4 Scale... 18-2 2-PanelDoors... 18-4 Bi-Parting(4-Panel)Doors... 18-5 GlazingOptions:3 Scale... 18-7 TrimOptions:3 Scale... 18-8 Standard Mullion Options: 3 Scale... 18-9 LiteCutInformationandOptions... 18-10 Unit Sizing, Rough Openings & Masonry Openings... 18-12 SectionDetails:6 Scale... 18-13 March 2011 JELD-WEN reserves the right to change specifications without notice. Page 18-1
GENERAL INFORMATION DIMENSIONAL DOORS Wood sliding patio doors may be specified as dimensional by adjusting the desired rough opening width or height in 1/8 increments from standard. Wood sliding patio doors are available in single, twin, triple and quad panel doors. The standard size range includes sizes specifically designed for replacement of older patio door models in existing structures, as well as a full range of true size products for architectural consistency. X o OPERATION Wood sliding patio doors are available in a full range of operating and stationary styles. Single panel doors are only available as stationary (non-venting) styles. Two-panel doors are available with left or right operation. Three-panel doors are available with left and right operation and with center or end operators. Four-panel doors are available with two panels operating from the center. Configuration and handing is based on viewing the door from the exterior. MULTIPLE ASSEMBLIES Wood sliding patio doors are available in a variety of multiple panel configurations from the factory, al of which are assembled with continuous sills. Mulling of wood gliding patio doors to like products in the field is not recommended. Instead, individual factory assembled units should be installed in contiguous rough openings, in order to provide adequate framing support to assure the best performance of the door systems. March 2011 JELD-WEN reserves the right to change specifications without notice. Page 18-2
ELEVATION NOTES ELEVATION DRAWINGS UTILIZE A LIMITED NUMBER OF PROJECTED LINES TO PRODUCE A RUDIMENTARY DRAWING INTENDED TO BE USED IN A SMALL GRAPHICAL SCALE. ELEVATIONS ARE VIEWED PERPENDICULAR FROM THE EXTERIOR OF THE STRUCTURE. IF MORE DIMENSIONS ARE NEEDED, USE THE SECTION DRAWINGS FOR MORE COMPLETE DEPICTIONS. M.O. Brickmould M.O. Adams/Flat Casing Rough Opening Frame Size Daylight Opening 62 15/16 [ 1599 ] 65 15/16 [ 1700 ] 60 [ 1524 ] 59 1/2 [ 1511 ] 19 [ 483] Masonry Openings for Brickmould, Flat & Adams Casing. Vertical measurements for transoms include sill nose. (Subtract 1/2 from Masonry Opening for Unit Size) 81 19/32 [ 2072 ] 83 3/32 [ 2111 ] 80 [ 2032 ] 79 1/2 [ 2019 ] 64 [ 1626 ] OUTSIDE OF EXTERIOR TRIM DAYLIGHT OPENING WFSU1 INDICATES TRADITION PLUS PRIMED FRENCH SLIDING PATIO DOOR WFSU1-50X68 BOOK CODE THE LAST TWO NUMBERS INDICATE THE UNIT HEIGHT THE FIRST TWO NUMBERS INDICATE THE UNIT WIDTH GENERAL SWINGING DOOR NOTES ELEVATION SYMBOL LEGEND 1. TRADITION PLUS PRIME FRENCH SLIDING PATIO DOOR (WFSU1) UNITS ARE AVAILABLE AS OPERATING OR FIXED UNITS. 2. UNIT ELEVATIONS ARE SHOWN WITH BRICKMOULD. TRANSOM UNITS ARE SHOWN WITH BRICKMOULD AND SILL NOSE. 3. OPERATING UNITS ARE AVAILABLE AS LEFT OR RIGHT HAND OPERATION. M.O. MASONRY OPENING March 2011 JELD-WEN reserves the right to change specifications without notice. Page 18-3
2-PANEL DOORS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 62 15/16 (1599) 65 15/16 (1700) 60 (1524) 59 1/2 (1511) 19 (483)[2] 74 15/16 (1903) 77 15/16 (1979) 72 (1829) 71 1/2 (1816) 25 (635)[2] 98 15/16 (2513) 101 15/16 (2588) 96 (2438) 95 1/2 (2426) 37 (940)[2] 81 19/32 (2072) 83 3/32 (2111) 80 (2032) 79 1/2 (2019) 64 (1626) WFSU1-50X68 WFSU1-60X68 WFSU1-80X68 83 (2108) 82 1/2 (2096) WFSU1-50X6B WFSU1-60X6B WFSU1-80X6B 97 19/32 (2479) 99 3/32 (2517) 96 (2438) 95 1/2 (2426) 80 (2032) 84 19/32 (2149) 86 3/32 (2187) 67 (1702) WFSU1-50X80 WFSU1-60X80 WFSU1-80X80 ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS Note Elevations shown DO NOT have exterior trim. Subtract 3/4 (19) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE: 1/4 = 1 March 2011 JELD-WEN reserves the right to change specifications without notice. Page 18-4
BI-PARTING (4-PANEL) DOORS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 121 7/16 (3085) 124 7/16 (3161) 118 1/2 (3010) 118 (2997) 19 (483)[4] 145 7/16 (3694) 148 7/16 (3770) 142 1/2 (3620) 142 (3607) 25 (635)[4] WFBU1-100X68 WFBU1-120X68 83 (2108) 82 1/2 (2096) 67 (1702) 81 19/32 (2072) 83 3/32 (2111) 80 (2032) 79 1/2 (2019) 64 (1626) WFBU1-100X6B WFBU1-120X6B 97 19/32 (2479) 99 3/32 (2517) 96 (2438) 95 1/2 (2426) 80 (2032) 84 19/32 (2149) 86 3/32 (2187) WFBU1-100X80 WFBU1-120X80 ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT Note Elevations shown DO NOT have exterior trim. Subtract 3/4 (19) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE: 1/4 = 1 March 2011 JELD-WEN reserves the right to change specifications without notice. Page 18-5
BI-PARTING (4-PANEL) DOORS M.O. BRICKMOULD M.O. ADAMS/FLAT CASING ROUGH OPENING FRAME SIZE DAYLIGHT OPENING 193 7/16 (4913) 196 7/16 (4990) 190 1/2 (4839) 190 (4826) 37 (940)[4] 81 19/32 (2072) 83 3/32 (2111) 80 (2032) 79 1/2 (2019) 64 (1626) WFBU1-160X68 83 (2108) 82 1/2 (2096) 67 (1702) WFBU1-160X6B 97 19/32 (2479) 99 3/32 (2517) 96 (2438) 95 1/2 (2426) 80 (2032) 84 19/32 (2149) 86 3/32 (2187) WFBU1-160X80 ELEVATION SYMBOL LEGEND: M.O. = MASONRY OPENING VALUES IN () ARE IN MILLIMETER CONVERSIONS VALUES IN [] ARE NUMBER OF DAYLIGHT OPENINGS PER UNIT Note Elevations shown DO NOT have exterior trim. Subtract 3/4 (19) from M.O. (Masonry Opening) for Unit Sizes. Masonry Openings above include Sill Nose, see Trim Options page for Sill Nose specifications. For other Trim Options refer to the Unit Sizing, Rough Opening & Masonry Openings page. SCALE: 1/4 = 1 March 2011 JELD-WEN reserves the right to change specifications without notice. Page 18-6
GLAZING OPTIONS INTERIOR GLAZED 3/4 [19.25mm] INSULATED GLASS 3/4 [19.05mm] 3/4 [19.05mm] LAMINATED INSULATED CLEARORLOW-E 3.0mm//6.7mm LAMINATE LAMINATED INSULATED TINTED 6.7mm LAMINATE//3.0mm SCALE: 3 = 1 March 2011 JELD-WEN reserves the right to change specifications without notice. Page 18-7
TRIM OPTIONS EXTERIOR TRIM 1 1/16 [27] 1 7/32 [31] 2 [51] 1 7/32 [31] 1 11/32 [34] 31/2 [89] 3 [76] 31/4 [83] 23/4 [70] BRICKMOULD FLAT CASING HERITAGE WOOD SUBSILL OPTIONS STANDARD SCALE: 3 = 1 March 2011 JELD-WEN reserves the right to change specifications without notice. Page 18-8
STANDARD MULLION OPTIONS DIRECT SET GEOMETRIC FRENCH VIEW SLIDER DIRECT SET OVER FRENCH VIEW SLIDER FRENCH VIEW TRANSOM OVER FRENCH VIEW SLIDER FRENCH VIEW SLIDER NEXT TO FRENCH VIEW INSWING SIDELIGHT FRENCH VIEW SLIDER NEXT TO FRENCH VIEW OUTSWING SIDELIGHT SCALE: 3 = 1 March 2011 JELD-WEN reserves the right to change specifications without notice. Page 18-9
LITE CUT INFORMATION Wood Sliding patio doors are available with removable grilles in 7/8, 1-1/8 and 1-3/8 widths, with grilles between the glass (GBG), or with Simulated Divided Lites. Standard lite cuts are rectangular. LITE CUT OPTIONS Special lite cut patterns can include a wide variety of straight line and radius patterns. The illustrations shown here represent just a few of the possibilities. Rectangular, horizontal, vertical and Prairie lite patterns are available in all standard size Wood Sliding patio doors. Uneven, diamond, radius and Gothic lite cuts are available, subject to approval. Approvals are based on the ability to fulfill the design requirement while maintaining the construction integrity of the finished product. RECTANGULAR HORIZONTAL VERTICAL PRAIRIE UNEVEN DIAMOND RADIUS GOTHIC BAR ALIGNMENT Alignment of divided lite muntin bars from one product to the next is often required by fine architectural design. Wood grilles, GBG s, and Simulated Divided Lites may be specified with muntin bars aligned. March 2011 JELD-WEN reserves the right to change specifications without notice. Page 18-10
DIVIDED LITE OPTIONS 3/4 [19.25mm] 3/4 [19.25mm] 3/4 [19.25mm] 5/16 [7.43mm] 5/16 [7.49mm] 5/16 [7.43mm] 5/16 [7.49mm] 5/16 [7.43mm] 5/16 [7.49mm] 7/8 [22.22mm] 7/8 [22.22mm] 11/8 [28.37mm] 11/8 [28.57mm] 13/8 [34.66mm] 13/8 [34.92mm] 7/8 SDL 11/8 SDL 13/8 SDL 3/4 [19.25mm] 3/16 [4.75mm] 3/4 [19.25mm] 3/4 [19.25mm] 3/16 [5.51mm] 5/16 [8.00mm] 5/8 [15.88mm] 23/32 [18.00mm] 1 [25.00mm] 5/8 GRILLE 23/32 GRILLE 1 GRILLE March 2011 JELD-WEN reserves the right to change specifications without notice. Page 18-11
CLEAR OPENING INFORMATION 1 13/32 [36] CLEAR OPENING PANEL WIDTH 5 5/32 [131] HORIZONTAL Two Panel Assembly 1 27/64 [36] CLEAR OPENING HEIGHT Clear Opening Formulas Horizontal Frame - (Panel Width + 6 9/16 ) = Clear Opening Vertical Frame - 3 11/32 = Clear Opening 1 59/64 [49] HORIZONTAL Four Panel Assembly 5 5/32 [131] 1 7/32 [31] 5 5/32 [131] PANEL WIDTH CLEAR OPENING PANEL WIDTH Clear Opening Formulas Horizontal Frame - ((2 x (Panel Width + 5 5/32 )) + 1 7/32 ) = Clear Opening Vertical Frame - 3 11/32 = Clear Opening March 2011 JELD-WEN reserves the right to change specifications without notice. Page 18-12
UNIT SIZING, ROUGH OPENINGS & MASONRY OPENINGS STANDARD OFFERING BRICKMOULD HORIZONTAL FRAME = UNIT SIZE GENERAL NOTES: UNITS WITH NO EXTERIOR TRIM FRAMESIZE=UNITSIZE UNITSIZEISALWAYSTHE EXTREME SIZE OF THE DOOR WITH OR WITHOUT TRIM ROUGHOPENINGISALWAYS3/4 OVER FRAME SIZE OF THE DOOR MASONRY OPENING IS ALWAYS 1/2 OVER THE UNIT SIZE OF THE DOOR VERTICAL FRAME = UNIT SIZE ROUGH OPENING: BRICKMOULD HORIZONTAL 3/8 [10] ROUGH OPENING 3/8 [10] 1 11/32 [34] 2 19/32 [66] 2 27/32 [72] 3/4 [19] UNIT SIZE FRAME TO EXTERIOR TRIM (UNIT) SIZE 3 [76] 23/4 [70] 1 11/32 [34] HORIZONTAL UNIT SIZE 31/2 FLATCASING FRAME + 6 [152] HORIZONTAL UNIT SIZE HERITAGE FRAME + 5 1/2 [140] HORIZONTAL UNIT SIZE BRICKMOULD FRAME + 2 11/16 [68] 3 [76] 23/4 [70] 1 11/32 [34] VERTICAL UNIT SIZE BRICKMOULD FRAME + 1 11/32 [34] VERTICAL UNIT SIZE HERITAGE FRAME+23/4 [70] VERTICAL UNIT SIZE 31/2 FLATCASING FRAME + 3 [76] VERTICAL ROUGH OPENING March 2011 JELD-WEN reserves the right to change specifications without notice. Page 18-12
SLIDING PATIO DOORR 1 7/32 5 25/32 2 7/32 4 9/16 3/4 41/4 1/2 Unit Size Screen Size Panel Size Glass Size Daylight Opening Frame Size Rough Opening 1/2 73/4 1 1/16 9/16 5 11/16 VERTICAL SECTION SCALE: 3 = 1 March 2011 JELD-WEN reserves the right to change specifications without notice. Page 18-13
2-PANEL DOOR 5 25/32 1 7/32 4 9/16 21/8 41/4 Panel Size Glass Size Daylight Opening 1/2 1/2 Screen Size HORIZONTAL SECTION 41/4 Rough Opening Frame Size Unit Size SCALE: 3 = 1 March 2011 JELD-WEN reserves the right to change specifications without notice. Page 18-14
BI-PARTING (4-PANEL) DOOR 3/8 41/4 1/2 Daylight Opening 1/2 Glass Size Panel Size Rough Opening Frame Size 41/4 Unit Size 5 25/32 4 9/16 HORIZONTAL SECTION 41/4 Panel Size Glass Size Daylight 1/2 Opening 1/2 Screen Size 41/4 March 2011 JELD-WEN reserves the right to change specifications without notice. Page 18-15 1 7/32 SCALE: 3 = 1