111
112
Cut Out Templates - Drop T & Compression Locks T1, T2, T3, V1, W1 C L C L C L C L C L C L C L C L C L 113 C L
PRODUCT NUMBER T1 T2 T3 V1 W1 EWTC140, EWTP140 WTC140, WTP140 UES052047 X UES052048 X UES052049 X 9/01503 X 9/01513 X 9/01561/01 X 9/01505 X 9/01515 X 9/01571/01 X DTP150 X 91247-MX X 275024-06 X 275063-68-S1 X 275021-06-S1 X 2751-10282-S1 X X X 114
Whale Tail Compression Lock W/ Electronic Actuator EWTC140, EWTP140 Cast EWTC140 - Chrome Plated EWTP140 - Black Powder Coated Cut out template: W1 171 64.5 41.1 70.1 140 18 60.7 COMPRESSED 68 RELEASED 72 24.9 39.4 ADJUSTMENT 7 59.4 2 39.4 241 135 92.7 R8.4 141 HOLE FOR 6.35 PADLOCK 72.6 86.4 ACTUATOR 11 0.76-3.1 PANEL RANGE R8.4 62 68 R16 Whale Tail Compression Lock WTC140, WTP140 Cast WTC140 - Chrome Plated WTP140 - Black Powder Coated Cutout Template: W1 141 41.1 70.1 140 18 HOLE FOR 6.35 PADLOCK 60.7 COMPRESSED 68 RELEASED 72 24.9 39.4 ADJUSTMENT 7 59.4 2 39.4 92.7 11 R8.4 0.76-3.1 PANEL RANGE R8.4 62 68 72.6 86.4 R16 115
Drop T Lock with Bent Tongue UES052047, UES052049, UES052048 Stainless Polished UES052047 Keyed alike. UES052049 Keyed differently. UES052048 Keyed alike, concealed fixing. Cutout Template: T2 100 5 95 79 R15 69 8 10.5 Drop T Lock with Bent Tongue 9/01503, 9/01513 9/01503 - Stainless 9/01513-9/01503 - Polished 9/01513-9/01503 - LH K/A FS880 9/01513 - LH K/A FS880 Cut out template - T2 100 5 95 R15 69 79 8 10.5 116
Drop T Lock 3 Way with Straight Tongue 9/01561/01 Stainless handle rod and guide Polished 100 Complete system, supplied with rods and guides. Assembled on site. 5 Can be purchased separately: 3/18702 - Spare rod 1050mm long 3/18716 - Spare guide 95 RECOMMENDED CUTOUT 79 Cut out template - T2 R15 69 8 10.5 Drop T Lock - Non-Locking with Bent Tongue 30 9/01505, 9/01515, 9/01505, - Stainless 9/01515, - 30 7.5 70 9/01505, - Polished 9/01515, - Cut out template - T3 102 90 100 5 69 120 68 90 RECOMMENDED CUTOUT 79 8 5 69 Drop T Lock with 8mm Square Shaft 9/01571/01 Stainless 120 69 7 21.5 70 Polished 124 95 8mm square shaft to suit. Locking. Keyed FS880 8 Cut out template - T2 95 R15 100 69 79 8 5 10.5 117
Drop T Lock Padlockable with Straight Tongue 70 121 DTP150 Stainless Polished 84 150 Built in padlock bracket for added security. Padlock not included. 100 5 Cut out template - T1 98 84 SUGGESTED CUTOUT 79 R15 98 8 10.5 Drop T Lock with Straight Tongue 63.5 121 91247 - MX Stainless Polished Stainless steel fascia 150 Cut out template - T1 100 5 95 79 R15 69 8 10.5 118
Vector Compression T-Handles 3 Way 275024-06 High impact BKV 133 plastic latching housing With Zinc Plated Handle 30.8 12.8 8 9 18 Black Powder Coated 82 131 Stainless steel spring loaded padlock eye. Compression mechanism supported by roller bearing for smooth actuation. Grip Range of 10mm - 60mm 90 rotation. 76.3 120 88 97 76,3 R5 275024-06 Handle will not lift when cylinder is locked. Gasket Seal Included. Use with 282109 Rods, 285023 Guide, and 282109 Adaptor. 2Nm Pressure required to fit nuts onto studs No tool required. 82 21 17 73 105 Cut out template - V1 5,5 27 Vector Compression T-Handles Rear Fixing 275063-68-S1 High impact BKV 133 plastic latching housing With Zinc Plated Handle 18 L 80 9 Black Powder Coated 131 IP65 Rated M5 Stainless steel spring loaded padlock eye. Compression mechanism supported by roller bearing for smooth actuation. Grip Range of 10mm - 60mm 120 97 76,3 R5 18 180 rotation. Handle will not lift when cylinder is locked. Integrated PUR seal. 2Nm Pressure required to fit nuts onto studs No tool required. 82 21 17 73 105 Dust shutter over cylinder Cut out template - V1 5,5 27 119
Vector Compression T-Handles Front Fixing 275021-06-S1 High impact BKV 133 plastic latching housing With Zinc Plated Handle 18 L 80 9 Black Powder Coated 131 Stainless steel spring loaded padlock eye. Compression mechanism supported by roller bearing for smooth actuation. 120 5,5 Grip Range of 10mm - 60mm 180 rotation. Handle will not lift when cylinder is locked. Gasket Seal included Cut out template - V1 82 21 97 76,3 R5 17 73 105 5,5 27 Vector Compression T-Handles With Mounting Bracket 2751-10282-S1 High impact BKV 133 plastic latching housing With Zinc Plated Handle 17,9 L 9,5 Handle Chrome Plated 149 IP65 Rated Compression mechanism supported by roller bearing for smooth actuation. Grip Range of 17mm - 52mm. 180 rotation. 139 Rotation 180 97 76,3 R5 Integrated PUR Seal. 21 17 Mounting Bracket Included. Cut out template - V1 82 73 105 5,5 27 120
Push To Close Latch Chrome Plated 10204 Zinc Alloy Chrome Plated 14.5 88 82 109 Internal locking and release deadbolt action. Each lock set includes 2 overmoulded keys (CF301) and all mounting screws except striker plate screws. GASKET 62 FRONT HOUSING 32-38 BACK HOUSING Push to Close Latch Black P/C 15605-01, 29790-04 110 Die Cast Zinc Alloy Black Powder Coated 29790-04 88 Internal Locking and Release using dead bolt action 29790-04 - External Handle 15605-01 - Internal Handle 20.7 16 120 16.5 72 110 Suggested Cutout 94 15605-01 121
Motor Home Entrance Lock 29412-07, 31073-05 Die Cast Zinc Alloy Black Powder Coated 15.19 12.7 29412-07 Internal Locking and Release using dead bolt action 137.16 29412-07 - External Handle 31073-05 - Internal Handle Handle can be locked before door is closed 12.13 162.24 Can be used with Central Locking Kit 22316-01 or Actuator 36517-01 181.69 31073-05 126.7 137.16 Recommended Cutout 123.2 Two Way Paddle Lock 22676-10 Die Cast Zinc Alloy 93.47 51.31 R7.1 Black Powder Coated Can be used with Central Locking Kit 22316-01 or Actuator 36517-01 155.19 77.6 10.84 TRAVEL 16.387 Suitable for use with Rotary Locks 18610-01, 18611-01 and Pin 11111-16 This lock is ideal for any application where central locking is required Examples include: Canopies Toolboxes Storage lockers 34.9 24.1 4.8 62.5 R4.78 R1.5 16 119.4 16 RECOMMENDED CUTOUT 24.1 32.54 122
Three Way Paddle Lock 19583-08 Die Cast Zinc Alloy 132.72 Black Powder Coated 129.54 Can be used with Central Locking Kit 22316-01 or Actuator 36517-01 Suitable for use with Rotary Locks 18610-01, 18611-01 and Pin 11111-16 This lock is ideal for any application where central locking is required Examples include: Undertray Toolboxes Storage lockers Mounting Bracket not included Suits Mounting Bracket 20503-01 19.55 59.68 RECOMMENDED CUTOUT 111.13 R15.24 116.84 R165.1 37.58 Recessed Paddle Lock With Rotary Latch 16268-13, 81348, 10335-16 Stainless 7.6 Raw The two step rotary latch provides positive slam action and anti-burst protection. This prevents accidental opening through vibration or impact. 16268-13: Paddle Lock 81348: Seal 10335-16: Pin to Suit 101.6 139.7 19.1 99.1 114.3 116.15 Items Sold Separately 57.1 84.94 RECOMMENDED CUTOUT 123 47.4 R6.35
Electronic Control Unit for Central Locking 22316-01, 22311-01, 22311-02, 36448-01 This electronic system consists of compatible components that allow for keyless entry for on or off road equipment. This system is perfect for any vehicle that doesn t currently have central locking capabilities. This unit comes with 22311-01 FOB as standard. 22316-01 unit will operate up to 60 control FOBs (remotes) and up to 20 door locks. 4 signals are emitted from each control FOB. Examples of use could be: 1) Lock all 2) Unlock all 3) Operate Zone A or Lighting 4) Operate Zone B or Generator etc. 22316-01 Installation instructions available upon request Increased end user convenience Easy and intuitive to operate Increased vehicle security Lighting and auxillary output control Complete kit with wire harnesses and accessories Standard 12V power Use with: 36157-01 Actuator 19583-08 Lock 22676-10 Lock 29412-07 / 31703-05 Complete Lock 29790-04 / 15605-01 Complete Lock 36448-01 KEYPAD Keypad unit will hold up to 5 different access codes at any time. Access codes can be changed when personnel operating the system change. If incorrect code is entered after 20 button presses, the keypad enters inactive mode for 1 minute. 22311-01 22311-02 Electronic Lock Actuator 36517-01 High Impact Plastic Black 40.3 Electronic actuator for use on locks and handles to create central locking for the user 12V supply, drawing up to 4.0 amps. 79.1 Motor is equipped with a 12V thermal protection for excessive heating due to extreme usage such as rapid, frequent operations or sustained activation. Wire length = 184mm 22.1 52.8 13.1 27 61.3 24.2 124
Flush Paddle Latch FU902BB, FU902P/SS, FU902, FU902SS Stainless - FU902P/SS, FU902SS - FU902BB, FU902 120 105 76 - FU902 Black Powder Coated - FU902BB Polished - FU902P/SS, FU902SS A 21.9 75 80 92 A C/W Gasket FU902P/SS Non Locking FU902, FU902BB, FU902SS Locking Suggested outline of cutout 21 42.5 22 4.8 1.5 SECTION A-A Flush Paddle Latch - Weatherproof 9/05462, 9/00406 / Acetal Copolymer Black 9/00406 - SS striker plate sold separately The traditional paddle handle has been completely redesigned to make major improvements in function and specification. This new model will not corrode, will resist entry of water and is quickly installed without visible bolts or rivets. 48 Ø7 20 31 9/00406 55 125
Vector Paddle Lock With Hooked Cam 2800-0020300101 Glass Fibre Reinforced Polyamide Bracket: Mild Handle: Black Bracket: Zinc Plated 115 IP65 Rated Integrated PUR Seal This Paddle lock comes complete with internal mounting bracket to allow easy installation. The hooked cam ensures positive latch when closing. The cam comes with an internal release capability which is a safety feature to ensure no one is locked inside. 150 M6 Ø6 Ø6.5 H=16 9 20 55 MAX 5 L=55 RECOMMENDED CUTOUT 82 112 Vector Paddle Lock 2 Way 2800-0020400100 Glass Fibre Reinforced Polyamide Bracket: Mild Handle: Black Bracket: Zinc Plated 115 IP65 Rated Integrated PUR Seal This Paddle lock comes complete with internal mounting bracket to allow easy installation. 150 This lock can be used with 282135-01 Slam Catch 282119-10 10mm Rod Adaptor 282130-1200MM 10mm Rods OR 282119 8mm Rod Adaptor 282109 8mm Rods MAX 5 46.5 63.8 RECOMMENDED CUTOUT 82 112 126
Recessed Paddle w/ Rotor Latch 9/00492, 9/00426 (Striker Pin) 9/00492 Stainless 9/00426 9/00492 Polished 9/00426 2 Stage Rotary Lock Recessed Paddle Latch 9/00448/01, 9/00449, 9/00406, Stainless 9/00448/01, 9/00449 - Polished 9/00406 - Raw 95 140 9/00448/01 - Locking 9/00449 - Non-Locking 9/00406 - Loop Striker Bilnd-mounting models have four studs (M6x10mm) welded on inside rim. Striker made in 6mm diameter stainless rod, welded to stainless back plate. 83 94 108 48 5 110 12 36 9/00448/01 9/00406 7 20 55 48 31 Anti-Burst Lock 3-Way Key Locking 0881/510 / Stainless 140 Black / SS Paddle 50 18 15 89 7 11.3 18 19 127
Flush Paddle Locks 9/00408, 9/00418, 9/00418/01, 9/00418/01/IR Stainless Raw 9/00408 Non-locking 9/00418 Locking. FS keys are standard 9/00418/01 Keyed alike. Keyed FS 880 9/00418/01/IR A knob for inside release can be fitted to all slam-bolt models. This operates even when paddle has been locked from the outside. (Add suffix IR to part number) 9/00408 9/00418 Flush Paddle Lock with Hook Cam 91262 Stainless Polished 12 6 84 72 44 WEIGHT 220g 112 77 48 Flush Paddle Lock - Key Locking K/A 91264 Stainless 10.6 5 Polished WEIGHT 266g 82 72 36 36 72 82 24 33 128
Flush Paddle Lock 0907/001 0907/215S Material Finish Weight Features 0907/001 350g 0907/003 370g Interior Release 0907/014 460g Interior Release - Keyed in Pairs 0907/015 460g Interior Release, K/A 64001 0907/514 / Stainless Black / SS Paddle 460g Interior Release - Keyed in Pairs 0907/215S / Stainless Black / SS Paddle 461g Interior Release, K/A 64001 Flush Paddle Lock 0912/401, 0912/410, 0912/418S, 0912/411 Stainless Polished 0912/401 Non-locking no interior release Weight: 410g 0912/410 Locking no interior release Weight: 470g 0912/410 0912/411 Locking no interior release All keys to pass Weight: 470g 0912/418S Locking with interior release Weight: 470g 129
Coach Bin Door Lock 602-0405 600-0488 602-0579 - Plastic All other - 602-0579 - Black 602-0600 - Chrome finish 602-0620 - Black plastic head All other - 602-0405 - Coach bin lock complete assembly. 602-0579 - Lock handle 602-0600 - Lock cylinder 602-0620 - Lock key Other components to be ordered seperately: 600-0485 - Anti burst lock LH 600-0486 - Anti burst lock RH 600-0487 - Lock striker pin 600-0488 - Lock connecting rod 600 0488 600 0486 600 0488 600 0487 600 0485 600 0487 602 0405 black 24 Volt Electric Bin Door Kit 602-0573, 602-0562, 602-0658, 602-0552 602-0573 - 24 Volt central locking unit with key and remote 602-0562 - 24 Volt electric bin door kit 602-0658 - Handle and solenoid 602-0552 - Connector module 602-0573 602-0552 47 158 145 118 10 6.5 602-0562 36 81 95 130
Two Stage Rotary latches 18610-01, 18611-01 Casing: High Strength Springs: Non Corrosive Stainless Casing: Zinc Plated Springs: Raw 18610-01: Left Hand 18611-01: Right Hand 6.6 Pictured: 18610-01 LH 19.8 Two Stage Rotary latches Used with pin 11111-16. Ø6.35 These latches can be used with any lock that has 2 or 3 way latching capabilities These latches are suitable for doors up to 91kgs Pictured: 18610-01 LH 2.16 50.2 46 18.64 13.4 21.03 M6 41.28 15.6 61.52 82.55 113.7 Striker Pin 111111-16 25.4 44 Zinc Plated 3.81 Use with Rotary Latches 18610-01: Left Hand 18611-01: Right Hand 3.81 Ø27.9 Ø17.07 - Ø17.19 M12 x 1.75-6g 21.59 Ø19.05 131
Rotor Latches 9/00423 (LH), 9/00424 (RH) Slam-action against striker pin, both hands available. Claw engages pin with 2-stage action, and is released by pull as shown on 2-lobe actuator arm. Clear zinc-plated throughout. Travel 6.5mm 21 Anti-Burst Properties When ring-tested, these latches can achieve values in excess of 8-9 KN* transverse load in fully latched condition. However, vehicle builders are responsible for evaluating performance in their own particular application and for ensuring that appropriate legislation is satisfied. 55 o *SAE & ECE11 Specification Rotor Latch Striker Pin 9/00425 Striker pin head 8mm x 4mm deep thread form 14 UNC Class 2A Not handed. 30 19 26 14 44 132
Lift & Turn Latches 62NBP, 62L1BP7 62L1BP7 Zinc Alloy Black Powder Coated 60 56 GRIP RANGE 62NBP: Non Locking 62L1BP7: Locking Environmental sealing is achieved by using a cup gasket and sealing the mounting screw threads. Screw and lockwasher assembly M5 x 16. For door thickness greater than 6 calculate screw length using the following formula: Door thickness +10 Two flat keys provided. 62L1BP7 85.1 40 62NBP 4 34 3 COMPRESSION CAM RETAINING CLIP LOCKWASHER PRE-SET NUT SCREW & LOCKWASHER ASSEMBLY M5 FLARED MOUNTING BRACKET Large Compression Lock 10207B-CP, 10207B-BLK 30 110 10207B-CP - Chrome Plated 10207B-BLK - Black Powder Coated 57 Grip range 15-30mm 66 4.4 28 92 34.5 Small Compression Lock 10208B-CP, 10208B-BLK 114 87 10208B-CP Chrome Plated 10208B-BLK Black Powder Coat 41 Grip range 15-30 mm 70 24 59 133
Push to Close Latch C2L1BP7, C2L1BP9, C2L1WP7, C2N1BP, C2NF1BP, C2NF1WP Zinc Alloy Black & White Powder Coated Heavy duty, low profile C2L1BP7 Locking, raised trigger, Black Keyed CH751 16 GRIP RANGE 1-24mm 15 35 C2 White C2L1BP9 Locking, raised trigger, Black Keyed SL019 C2L1WP7 Locking, raised trigger, White Keyed CH751 93 Non Locking, Flush Trigger Model C2N1BP Non Locking, without lock, Black C2NF1BP Non Locking flush trigger, Black C2NF1WP Non Locking, flush trigger, White 34 41 22 Large Compression Latch C5L1BP7, C5L2BP7, C5L2CP7, C5L3CP7, C5L3BP7, C5L4BP7 Zinc Alloy Black Powder Coat & Chrome Plated Heavy duty, low profile C5L1BP7 Grip range 1-14mm, Locking, Keyed CH751 12 C5L2BP7 Grip range 15-29mm, Locking, Keyed CH751 C5L2CP7 Grip range 15-29mm, Chrome plated Locking, Keyed CH751 C5L3CP7 Grip range 30-45mm, Chrome Plated Locking, Keyed CH751 110 15 C5L3BP7 Grip range 30-45mm, Locking, Keyed CH751 C5L4BP7 Grip range 46-57mm, Locking, Keyed CH751 50 134
Push Button Anti Burst Lock 9300/001, 9300/002 Plastic Black 9300/001 Push button handle, keyed in pairs. 9300/002 Push button handle, keyed alike This system is ideal for use on any door, especially tractor cabs etc. Anti Burst Type Cab Door Lock 9301/001, 9301/002, 9301/S 9301/001 Left Hand 9301/002 Right Hand This door lock is an anti burst type lock and is operated by the above push button handle as well as its own inside integral lever handle, which can very easily be turned into a remote operation, and is supplied complete with striker pin 9301/S 9301/S (Striker pin for above) CamLock Light Duty Bolt-on - Suit 22mm OD Pipe K110-600 31.6 405.4 53.7 16 35.1 30 8.4 82.6 82.2 25 48 231.5 31 125.7 135 106.5
CamLock Medium Duty Bolt-on K110-500 113 9 57 Suits 27mm OD Pipe 385 410 CamLock Medium Duty Bolt-on AJ0057, UES0057 Suits 27mm OD Pipe AJ0057 - Wide Butt 53mm UES0057 - Narrow Butt 44mm Cam Lock Kit - Suit 34mm Diameter Tube CLK-1000 Weight: 3.30kg Suits 34mm OD Pipe Cam lock kit comes without tube 136
Magnetic Door Buffer & Holder 131011440 Black Traction force 500N. Ø27 tube Magnetic Door Buffer & Holder 131011441 Black Traction force 500N. Ø22 tube 137
Recessed Side Door CamLock ART10723 Stainless 02160309L - Cam Polished Handle 02160309M - Keeper 29mm for 16mm Diameter Rod 02160309M - Keeper 02160309L - Cam 2 cams and 2 keepers supplied 14.5 93 14.5 Recessed Side Door CamLock ART10092 Stainless 02160309L - Cam Polished Handle 35mm for 16mm Diameter Rod 02160309M - Keeper 02160309L - Cam 2 cams and 2 keepers supplied 02160309M - Keeper 336 59 102.5 102.5 59 6.5 5 16.5 152 139 76 119 16.5 35 29 303 24.5 14 138
Slam Latch - Heavy Duty Full Assembly 23.44445 Mainly INDIVIDUAL PARTS 23.44445PH Upper Zinc Plated Cam. Weight 0.255kg 23.44445GH Upper Zinc Plated Keeper Weight 0.225kg 23.44445AX Zinc plated steel pin DIA 16mm. Weight 0.27kg 23.44445CU base grey aluminium finish. Weight 0.5kg 23.44308PT Inside Teflon trigger. Weight 0.025kg 23.44445GU Graphite nylon bearing bracket. Weight 0.005kg 23.44445GO Grooved pin DIA 5mm x 26 self colour steel. 23.44445BA Chrome Plated locking cylinder. Weight 0.75kg 23.44445PO Zinc alloy handle grey Al finish. Weight 0.0.75kg 23.44445PB Lower Zinc Plated Cam Weight 0.255kg 23.44445GB Lower Zinc Plated Keeper Weight 0.15kg 23.44445PB 23.44445GB Plant On Slam Latch 2115/001, 2115/002 WEIGHT 380g 2115/001 LH 2115/002 RH Pressed steel case. Malleable iron tongue. PVC dipped handle. Left Hand 139
Slam Latch - Heavy Duty 9/00805, 9/00806 Yellow 32 165 Follow bush to take 8mm steel shaft 9/00805 - LH 9/00806 - RH PVC Dipped handle. 64 19 25.7 9/00805 - LH 9/00806 - RH 15.5 5 20 20 90 15 20 12.5 70 Internal Slam Latch 0891/001 (LH), 0891/002 (RH) WEIGHT 310g Right Hand Pressed steel case Malleable Iron tongue Cabin Screw-On Lock 600-0093, 600-0094, 580-0002 Complete with inner handle, supplied separately Left Hand Cabin Screw-On Locks Finish 600-0093 Left Hand Black 600-0094 580-0002 Right Hand Handle Black Chrome plated 140
Plant On Slam Latch 2121/003, 2121/004 WEIGHT 330g 2121/003 2121/003 Non-locking 2121/004 Locking Pressed steel case. Malleable iron tongue. Slam Latch General Purpose 3/17332, 3/17330 DIMENSION A 3/17330-10mm 3/17332-16mm Pressed case. Malleable Iron tongue 141
D-Latch Standard Pattern G3046PZN WEIGHT 240g D-Latch Improved Pattern G3047PZN, G8047PSS G3047PZN G8047PSS WEIGHT G3047PZN G8047PSS SS 165G 176G 142
End-Slam Latch 9/01187, 3/22387 9/01187 - Stainless 3/22387-9/01187 - Raw 3/22387 - Bolt projection variable, 9-16mm. Minimum load 5kg for full bolt travel. Mild steel model made in CR4. Stainless models in grade 304 with stainless bolt-pull, bolt and spring. Slam Latch 602-0138, 602-0141 Galvanised 602-0138 Spring catch (less hook handle) 602-0141 Spring catch, weight 180g Slam Latch 2467/001 10-15 34 38 5 Gold passivated WEIGHT 80g 17 40 5 18 143
Moulded Slam Latch w/ Pull Knob 9/01529, 9/01530 Acetal Copolymer Black The unique design of these latches allows fix through mounting to suit narrow door pillars, sections and channels. Moulded construction provides the benefits of light weight, self-lubricating action, and total corrosion resistance at an inexpensive price. Note: Knob & rivet can be supplied loose, for assembly after latch is installed in panel. 9/01529 Moulded slam latch, pulled knob fitment 9/01530 Moulded slam (no knob) Toilet Door Lock 600-0595, 600-0596 Polyamide Black WEIGHT 400g Micro switch with sensor: 600-0595 - LH 600-0596 - RH Without Micro switch: 600-0611 - LH 144
Hooked Budget Lock 3/16200, 3/16201 3/16200 LH 3/16201 RH Budget Locks UES421024, UES421025 UES421025 UES421024 - Left Hand UES421025 - Right Hand Budget Lock Key 2257/001, 2257/004 WEIGHT 2257/001 60g 2257/004 130g 2257/001 83mm 2257/004 130mm 145
Budget Lock 3/09656, 3/09656SS 3/09656 3/09656SS 316 Stainless 3/09656 3/09656SS Raw Simple dead-bolt latches in which bolt can move 180 completely through the case. Push to Close Latch A31BP, A32BP ABS, SS Spring Black 25 57 FINGER DEPRESSION 28 DOOR THICKNESS Single hole snap-in installation TOTAL GRIP Corrosion resistant materials 6.5mm A31BP - Suits 1.5mm Door thickness A32BP - Suits 2.0mm Door thickness FRAME 47 2 15 6.4 LATCH TRAVEL SLIDE SPRING Striker plate - Two Step 1/27113 (Alt # 2268/001) Zinc Die-Cast Useful 2 step striker with adjustable mounting holes. Use with most slam latches, paddle latches. Serrated base. Striker Plate X1 Zinc Die-Cast 146
Budget Lock Escutcheon 0130/001 Zinc Die-Cast Chrome Plated WEIGHT 20g Gravelly Fastener w/ Plate 0662/001 Die-cast Chrome Plated WEIGHT 70g 147
Internal Release Handle (Suits CT1178 Series) HA-602H Nylon Inside release handle with fluorescent mushroom head. Refrigeration Door Lock CT-1178 - with Offset Striker CT-1178/1 - with Flush Striker Chrome Plated 28 56 78 H = 90mm - Offset Striker H = 50mm - Flush Striker 72 56 69 52 38 Chrome slam latch with offset striker adjustable in 2.5mm increments and inside release handle. 6 This latch is widely used for large size insulated enclosures, such as cold stores or containerised units, where a surface-mounted latch is preferrable to avoid breaching the integrity of the door. H 57 10 Hole for Padlock (7mm) 156.5 10 50 With slam action against a roller striker, this system can be used on doors flush fit against the frame or offset between 35-70mm height. There is an inside safety punch handle for emergency release. 148
Flush Pull Latches M1N1B,-C,-W,-SS; M1L1B,-SS UL94-HB ABS or 316 Stainless Ø61 32 26 13 Black, White, Cream polymer Satin Finish Stainless ABS Heavy duty design M1N1B - Non Locking Black M1N1C - Non Locking Cream M1N1W - Non Locking White M1N1SS - Non Locking Stainless M1L1B - Locking Black M1L1SS - Locking Stainless M1N1B, M1N1C, M1N1W, M1L1B - Panel Thickness 0-8 mm M1N1SS, M1L1SS - Panel Thickness 0-7 mm 21.4 3 32 Stainless For 12mm - 20mm applications use bracket M1WBK Push Button Latch 93NB, 93LB7 ABS Body; SS304 Keeper & Washer 22 38.1 19.1 Black 55.2 5.6 Push button opening with a single hole installation. 93NB - Non Locking 93LB7 - Locking CH751 31.8 Compartment Locks 1/27900, 1/27900/12, 1/27902, 1/27900/24 Zinc Die-Cast 19 Chrome Plated 1/27900 - Mixed Keys 1/27900/12 - K/A FS901 1/27902 - K/A FS880 1/27900/24 - FS904 26 37 90 6 28 149
Compartment Locks CML1CP7 CML1CP7-AC CML1CP7-CW CML2CP7-AW CML2CP7-CW CMN2BPW-CW Chrome Plated Chrome Plated Chrome Plated Chrome Plated Black P/C Anti-clockwise Clockwise Anti-clockwise Clockwise Wing Head GRIP 16mm 16mm 22mm 22mm 22mm GRIP 6-26mm 6-26mm 12-32mm 12-32mm 12-32mm Keyed CH751 22 16 4 34 Grip Supplied with 2 cams 40 30 Wing Head Clip N Turn 1618001, 1618003, 1618005 Polyoxymethylene Black GRIP (H) 1618001 13.5mm 1618003 18mm 1618005 25mm Quick tool-less assembly Panel thickness: Up to 4mm for 13.5mm and 18mm Up to 6mm for 25mm 40 150
E3 Compression Latch Keys Die-cast Zinc Alloy Compatible With: Chrome Plated ADAPTABLE to E3, E5 E3K7S - 7mm Square Driver E3K7T - 7mm Triangle Driver E3K8S - 8mm Square Driver E3K9R - 9mm Round Driver E3K3P - 3mm Double Bit UES E3 UES E5 8mm Square 7mm Square Round Double Bit 7mm Triangle E3 Compression Latch Die-cast Zinc Alloy Chrome Plated (E3L1CPXX) Black (E3L1BPXX) E3L1BP7S - 7mm Square Driver - Black E3L1BP7T - 7mm Triangle Driver - Black E3L1BP8H - 8mm Hex Driver - Black E3L1BP8S - 8mm Square Driver - Black E3L1BP9R - 9mm Round Driver - Black E3L1BPTH7 - T-Handle Locking Head Black E3L1CP3P - Double Bit 3mm Driver Chrome E3L1BPDS - Slot Driver - Black E3L1BPWH - Wing Head Driver - Black E3L1SS7T - Stainless 7mm Triangle Driver - Black E3L1SS8H - Stainless 8mm Hexagon Driver - Black Double Bit 7 or 8mm Square 7mm Triangle UES KEY (Sold Separately). 9mm Round Slotted Head Wing Head ALL LATCHES COME WITH 3 CAMS OFFERING A GRIP RANGE OF 12MM - 81MM Double Bit Chrome 7mm Triangle SS 151
E5 Latch E5L1BP7S, E5L1BP7T Die-cast Zinc Alloy 20 Chrome Plated 0.5 Gasket 4.3 44 E5 Head Key Styles E5L1BP7S - 7mm Square Driver E5L1BP7T - 7mm Triangle Driver 7 Ø 31 19.4 LATCHES COME WITH 4 CAMS OFFERING A GRIP RANGES OF 6.5MM, 11.5MM, 15.5MM + 18MM 7 Ø 31 23 7mm Square 7mm Triangle Key 9mm Round E3SK9R 2.1 R5 R4.75 5.3 Zinc Plated Suits small E3S latch 41.5 50 Quarter Turn Latch E5N1BPWH 44 30 Zinc Plated, Black P/C Wing Head Supplied with 4 cams Grip Range: 7mm 10mm 12mm 20mm 20 Grip Range 48 152
Vibration Resistant Quarter-turn Fastener QT18 Zinc Die-Cast Chrome Plated Vibration resistant Assebled to IP 65/Nema 4 Complete with earth nut Zinc die-cast housing CP 32mm diamater X 18mm Fastener for any application requiring a quarter turn action to secure doors etc. The cam snaps in at the open and closed positions, preventing unintentional opening of the fastener due to vibrations. P/N without projection H in mm Cams sold separately Quarter-turn Latches 3mm Double Bit 5mm Double Bit 7mm Square 7mm Triangle 8mm Square-Slotted 8mm Square 8mm Triangle Slotted Quarter Turn Lock - 8mm Square QT18-8S-SS, 233009 Stainless QT18-8S-SS Qtr turn Polished QT18-8S-SS and 233009 Sold Separately Stainless steel quarter-turn fastener for applications where high corrosion resistance is required. Acid proof steel quality for extreme environments. 233009 Cam 153
Cam Lock - Keyed Alike NAL-D Brass Body, Key and Cam Chrome Body, Nickel Finish Key Brass cylinder tubular lock cam. 90 cam rotation. Key is removable in locked position only. Keyed alike. Cut Out Dimensions Cam Lock - Mini - Keyed Alike NAL-S Zinc Alloy Chrome 90 cam rotation. Cam is reversible. NAL-S-1 : Key withdraws in locked position only (key works as a knob in unlocked position) NAL-S-2 : Key withdraws in both locked and unlocked positions NAL-S CAP : Black polythylene cover for dust Cut Out Dimensions 154