S BBES
ÍNDICE S TÉCNICAS AFLAS-B85 EPDM-B85 EPDM-85-KTW EPDM-W85-FDA FPM-B85 FPM-B85-GD FPM-B85 FPM-B85-FDA HNB-B85 HNB-B85-GD HNB-B85-GD-LT NB-B85 NB-W85-FDA SILICONE-B85-FDA SILICONE-85-FDA 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
AFLAS-B85 BBES Material Data Sheet AF101-B85 AFLAS* AF101 black (bisphenol cross linked) AF101-B85 is a Tetrafluoroethylene/Propylene copolymere (TFE/P), commonly referred to as FEPM or AFLAS*. AFLAS* has a very high resistance to hydraulic fluids (incl. Alkyl-Acryl-Phosphate Esters), all break fluids (on glycol, mineral and silicone base), acids, steam and hot water, sour oils/gases (H2S) and heavily formulated oils with amine additives. g/cm3 1,68 Hardness at 20: DIN 53505 Shore A 85 ±5 Tensile strength: DIN 53504 N/mm 2 7,2 ±15% Elongation at break: DIN 53504 % 236 ±20% Modulus 100%: DIN 53504 N/mm 4,2 ±30% Tear strength: DIN 53507B N/mm 7,2 Compression set: 70h/T DIN 53517A % 27,0 ±20% Compression set: 22h/70 DIN 53517A % 24,7 ±20% Compression set: 22h/100 DIN 53517A % 19,8 ±20% Compression set: 24h/175 DIN 53517 % 24,5 ±20% 210 Short time max. service temp. in air: 280-15 Water up to 90 Ozone Steam Break Fluids HFA, HFB fluids Solvents S HFC, HFD fluids Air up to 200 Mineral oils Vegetable oils Fuels S Key to chemical resistance: = resistant S = suitable = unsuitable Main application Static and dynamic seals (standard and special), wipers, O-rings, flange seals, rotary seals, rubber energizers (preload elements). Applications where high temp. and/or chemical resistance is required, oil and gas industry. Analysis and Evaluation The mentioned properties are only valid for test pieces of the corresponding ISO, DIN and ASTM standards. They cannot be directly related to seals, gaskets and other sealing products and should be used only as a general guide *) AFLAS is a reg. trademark of Asahi Glass Co./Japan. C/ Cicilisme 35 Pol. Ind. Can oses. ubí BCN CP 08191 93 588 90 91 www.qyps.es
EPDM-B85 BBES Material Data Sheet E131-B85 EPDM E131 black (peroxide cross linked) E131-B85 is a black Ethylene Propylene ubber, commonly referred to as EPDM. This material is often used in hot water steam applications as well as in fire resistant fluids where synthetic oils are used. EPDM materials are also used in bases, acids and alcohols. EPDM is also used for brake fluids, but we recommend observing local safety-regulations before installing an EPDM seal in breaking systems. EPDM is not resistant to mineral- vegetable- and animal oils. g/cm3 1,22 Hardness at 20: DIN 53505 Shore A 85 ±5 Tensile strength: DIN 53504 N/mm 2 12,8 ±15% Elongation at break: DIN 53504 % 200 ±20% Modulus 100%: DIN 53504 N/mm 6,2 ±30% Tear strength: DIN 53507B N/mm 3,2 Compression set: 70h/T: DIN 53517A % 20,9 ±20% Compression set: 22h/70: DIN 53517A % 20,7 ±20% Compression set: 22h/100: DIN 53517A % 19,8 ±20% Compression set: 22h/150: DIN 53517A % 40,9 ±20% -50 130 Water up to 90 Biodegradeable oils Steam up to 180 Fuels HFA, HFB, HFD-S fluids Ozone, Oxygen HFC, HFD- fluids Alcohols Mineral oils Ketones, Esters Vegetable oils Air up to 100 Silicone oils S Air up to 150 Key to chemical resistance: = resistant S = suitable = unsuitable Main application Static and dynamic seals (standard and special), wipers, O-rings, flange seals, rotary seals, rubber energizers (preload elements); cleaning and washing technology. Analysis and Evaluation The mentioned properties are only valid for test pieces of the corresponding ISO, DIN and ASTM standards. They cannot be directly related to seals, gaskets and other sealing products and should be used only as a general guide. C/ Cicilisme 35 Pol. Ind. Can oses. ubí BCN CP 08191 93 588 90 91 www.qyps.es
EPDM-B85 KTW BBES 9 9 9 9 6 9 9 9 B1!/ C/ Cicilisme 35 Pol. Ind. Can oses. ubí BCN CP 08191 93 588 90 91 www.qyps.es
EPDM-W85 FDA BBES Material Data Sheet E132-W85 EPDM-FDA E132 white (sulphur cross linked) E132-W85 is a white Ethylene Propylene ubber, commonly referred to as EPDM. This material is often used in hot water steam applications as well as in fire resistant fluids where synthetic oils are used. EPDM materials are also used in bases, acids and alcohols. EPDM is also used for brake fluids, but we recommend observing local safety-regulations before installing an EPDM seal in breaking systems. EPDM is not resistant to mineral- vegetable- and animal oils. EPDM-FDA E132 white is approved for the use of applications in contact with foodstuff. g/cm3 1,39 Hardness at 20: DIN 53505 Shore A 85 ±5 Tensile strength: DIN 53504 N/mm 2 7,3 ±15% Elongation at break: DIN 53504 % 374 ±20% Modulus 100%: DIN 53504 N/mm 4,2 ±30% Tear strength: DIN 53507B N/mm 5,8 Compression set: 70h/T: DIN 53517A % 22,3 ±20% Compression set: 22h/70: DIN 53517A % 45,1 ±20% Compression set: 22h/100: DIN 53517A % 77,9 ±20% -50 100 Short time max. service temp. in air: 130 Water up to 90 Biodegradeable oils Steam up to 180 Fuels HFA, HFB, HFD-S fluids Ozone, Oxygen HFC, HFD- fluids Alcohols Mineral oils Ketones, Esters Vegetable oils Air up to 100 Silicone oils S Air up to 150 Key to chemical resistance: = resistant S = suitable = unsuitable C/ Cicilisme 35 Pol. Ind. Can oses. ubí BCN CP 08191 93 588 90 91 www.qyps.es
FPM-B85 BBES Material Data Sheet F111-B85 FPM-black F111 (bisphenole cross linked) F111-B85 is a black Fluorocarbon elastomere, commonly referred to as VITON* and FPM. FPM materials have a very high resistance to hydraulic fluids, chemicals and a number of organic compounds and operate in temperatures between -25 to +210. F111-B85 is recommended for applications where its outstanding resistance to heat, chemicals, weathering and ozone is required. g/cm3 1,88 Hardness at 20: DIN 53505 Shore A 85 ±5 Tensile strength: DIN 53504 N/mm 2 11,5 ±15% Elongation at break: DIN 53504 % 180 ±20% Modulus 100%: DIN 53504 N/mm 7,3 ±30% Tear strength: DIN 53507B N/mm 6,4 Compression set: 70h/T DIN 53517A % 32,0 ±20% Compression set: 22h/70 DIN 53517A % 27,3 ±20% Compression set: 22h/100 DIN 53517A % 25,3 ±20% Compression set: 24h/175 DIN 53517 % 32,8 ±20% -25 210 Short time max. service temp. in air: 280 Water up to 90 S Biodegradable oils Steam Hydrocarbons HFA, HFB, HFC Fluids S Alcohols HFD-S, Diesel, Gasoline, Fuels Mineral oils Ozone, Oxygen Vegetable oils Air up to 200 Silicone oils Key to chemical resistance: = resistant S = suitable = unsuitable C/ Cicilisme 35 Pol. Ind. Can oses. ubí BCN CP 08191 93 588 90 91 www.qyps.es
FPM-B85 BBES.! < =.! < = : = : = = = = = C/ Cicilisme 35 Pol. Ind. Can oses. ubí BCN CP 08191 93 588 90 91 www.qyps.es
FPM-B85 Material Data Sheet F109-B85 (genuine VITON ) FPM F109 brown (bisphenole cross linked) BBES F109-B85 is a brown Fluorocarbon elastomere, commonly referred to as VITON and FPM. FPM materials have a very high resistance to hydraulic fluids, chemicals and a number of organic compounds and operating temperature ranges between -20 to +210. F109-B85 is recommended for applications where its outstanding resistance to heat, chemicals, weathering and ozone is required. g/cm3 2,44 Hardness at 20: DIN 53505 Shore A 85 ±5 Tensile strength: DIN 53504 N/mm 2 11,7 ±15% Elongation at break: DIN 53504 % 154 ±20% Modulus 100%: DIN 53504 N/mm 8,8 ±30% Tear strength: DIN 53507B N/mm 4,2 Compression set: 70h/T DIN 53517A % 14,1 ±20% Compression set: 22h/70 DIN 53517A % 9,4 ±25% Compression set: 22h/100 DIN 53517A % 6,0 ±25% Compression set: 24h/175 DIN 53517 % 9,4 ±25% 210 Short time max. service temp. in air: 280 Water up to 90 S Biodegradable oils Steam Hydrocarbons HFA, HFB, HFC Fluids S Alcohols HFD-S, Diesel, Gasoline, Fuels Mineral oils Ozone, Oxygen Vegetable oils Air up to 200 Silicone oils Key to chemical resistance: = resistant S = suitable = unsuitable Main application Static and dynamic seals (standard and special), wipers, O-rings, flange seals, rotary seals, rubber energizers (preload elements). Applications, where high temperature and/or chemical resistance is required. -20 Analysis and Evaluation The mentioned properties are only valid for test pieces of the corresponding ISO, DIN and ASTM standards. They cannot be directly related to seals, gaskets and other sealing products and should be used only as a general guide. C/ Cicilisme 35 Pol. Ind. Can oses. ubí BCN CP 08191 93 588 90 91 www.qyps.es
FPM-B85 FDA BBES Material Data Sheet F110-B85 FPM-FDA F110 brown (bisphenole cross linked) F110-B85 is a brown Fluorocarbon elastomere, commonly referred to as VITON* and FPM. FPM materials have a very high resistance to hydraulic fluids, chemicals and a number of organic compounds and operate in temperatures between -25 to +210. F110-B85 is recommended for applications where its outstanding resistance to heat, chemicals, weathering and ozone is required. FPM-FDA F110 brown is approved for the use of applications in contact with foodstuff. g/cm3 2,62 Hardness at 20: DIN 53505 Shore A 85 ±5 Tensile strength: DIN 53504 N/mm2 7,7 ±15% Elongation at break: DIN 53504 % 160 ±20% M odulus 100%: DIN 53504 N/mm 6,55 ±30% Tear strength: DIN 53507B N/mm 4,3 Compression set: 70h/T DIN 53517A % - Compression set: 22h/70 DIN 53517A % - Compression set: 22h/100 DIN 53517A % - Compression set: 24h/175 DIN 53517 % 27 ±20% Short time max. service temp. in air: Water up to 90 S Biodegradable oils Steam Hydrocarbons HFA, HFB, HFC Fluids Alcohols HFD-S, Diesel, Gasoline, Fuels Mineral oils Ozone, Oxygen Vegetable oils Air up to 200 Silicone oils Key to chemical resistance: = resistant S = suitable = unsuitable Main application Static and dynamic seals (standard and special), wipers, O-rings, flange seals, rotary seals, rubber energizers (preload elements). Applications in the food industry where high temp. and/or chemical resistance is required. Analysis and Evaluation The mentioned properties are only valid for test pieces of the corresponding ISO, DIN and ASTM standards. They cannot be directly related to seals, gaskets and other sealing products and should be used only as a general guide. *) VITON is a reg. Trademark of Du Pont Co./.S.A. -25 210 280 C/ Cicilisme 35 Pol. Ind. Can oses. ubí BCN CP 08191 93 588 90 91 www.qyps.es
HNB-B85 BBES Material Data Sheet HN112-B85 H-NB HN112 black (peroxide cross linked) HN112-B85 is a black hydrogenated acrylnitrile-butadiene-rubber commonly referred to as H-NB. Due to its good physical characteristics and chemical resistance to the most common hydraulic fluids it is an excellently suitable sealing material for a wide range of applications. H-NB materials are often used in vegetable and animal oils as well as in highly addivated oils, sour oils/gases (H2S) and crude oils. g/cm3 1,23 Hardness at 20: DIN 53505 Shore A 85 ±5 Tensile strength: DIN 53504 N/mm 2 21,7 ±15% Elongation at break: DIN 53504 % 215 ±20% Modulus 100%: DIN 53504 N/mm - Tear strength: DIN 53507B N/mm 6,6 ±15% Compression set: 70h/T: DIN 53517A % - Compression set: 22h/70: DIN 53517A % 20,2 ±20% Compression set: 22h/100: DIN 53517A % 22,3 ±20% -25 150 Water up to 90 Diesel Fuel Steam Gasoline Fuel S HFA, HFB, HFC Fluids Ozone Mineral oils Alcohols Vegetable oils Air up to 80 Silicone oils S Biodegradable oils S Key to chemical resistance: = resistant S = suitable = unsuitable Main application Static and dynamic seals (standard and special), wipers, O-rings, flange seals, rotary seals, rubber energizers (preload elements). application in petroleum fluids, water, greases, mineral oils, oil and gas industry. Analysis and Evaluation The mentioned properties are only valid for test pieces of the corresponding ISO, DIN and ASTM standards. They cannot be directly related to seals, gaskets and other sealing products and should be used only as a general guide. C/ Ciclisme 35 Pol. Ind. Can oses. ubí BCN CP 08191 93 588 90 91 www.qyps.es
HNB-B85 GD BBES & < < &/8 1 < 9 < 3/ 1 < 9 < < < C/ Ciclisme 35 Pol. Ind. Can oses. ubí BCN CP 08191 93 588 90 91 www.qyps.es
HNB-B85 GD-LT BBES ) 6 2#3 = = )42#) = = : = = = : = C/ Ciclisme 35 Pol. Ind. Can oses. ubí BCN CP 08191 93 588 90 91 www.qyps.es
NB-B85 BBES Material Data Sheet N107-B85 NB N107 black (sulphur cross linked) N107-B85 is a black Nitrile Butadiene ubber commonly referred to as NB, Nitrile or BNA. Because of its good physical characteristics and chemical resistance to the most common hydraulic fluids NB is excellently suitable for sealing material. NB materials are one of the most used elastomers in sealing applications. g/cm3 1,32 Hardness at 20: DIN 53505 Shore A 85 ±5 Tensile strength: DIN 53504 N/mm2 17,2 ±15% Elongation at break: DIN 53504 % 171 ±20% M odulus 100%: DIN 53504 N/mm 10,2 ±30% Tear strength: DIN 53507B N/mm 3,3 Compression set: 70h/T: DIN 53517A % 6,0 ±25% Compression set: 22h/70: DIN 53517A % 6,7 ±25% Compression set: 22h/100: DIN 53517A % 6,8 ±25% Water up to 70 Diesel Fuel Water up to 90 S Gasoline Fuel S Steam Alcohols HFA, HFB, HFC Fluids Ozone, Oxygen HFD Fluids Air up to 100 Mineral / vegetable oils Air up to 150 Silicone oils S Biodegradable oils S Key to chemical resistance: = resistant S = suitable = unsuitable Main application Static and dynamic seals (standard and special), wipers, O-rings, flange seals, rotary seals, rubber energizers (preload elements). applications in petroleum fluids, water, greases, mineral oils. Analysis and Evaluation The mentioned properties are only valid for test pieces of the corresponding ISO, DIN and ASTM standards. They cannot be directly related to seals, gaskets and other sealing products and should be used only as a general guide. -25 100 C/ Ciclisme 35 Pol. Ind. Can oses. ubí BCN CP 08191 93 588 90 91 www.qyps.es
NB-W85 FDA BBES Material Data Sheet N111-W85 NB-FDA N111 white (sulphur cross linked) N111-W85 is a white Nitrile Butadiene ubber commonly referred to as NB, Nitrile or BNA. Because of its good physical characteristics and chemical resistance to the most common hydraulic fluids NB is excellently suitable for sealing material. NB materials are one of the most used elastomers in sealing applications. NB-FDA N111 white is approved for the use of applications in contact with foodstuff. g/cm3 1,36 Hardness at 20: DIN 53505 Shore A 85 ±5 Tensile strength: DIN 53504 N/mm 2 7,9 ±15% Elongation at break: DIN 53504 % 305 ±20% Modulus 100%: DIN 53504 N/mm 4,5 ±30% Tear strength: DIN 53507B N/mm 7,6 Compression set: 70h/T: DIN 53517A % 21 ±20% Compression set: 22h/70: DIN 53517A % 23 ±20% Compression set: 22h/100: DIN 53517A % 29 ±20% 100 Short time max. service temp. in air 110 Water up to 70 Diesel Fuel Water up to 90 S Gasoline Fuel S Steam Alcohols HFA, HFB, HFC Fluids Ozone, Oxygen HFD Fluids Air up to 100 Mineral / vegetable oils Air up to 150 Silicone oils S Biodegradable oils S Key to chemical resistance: = resistant S = suitable = unsuitable -22 Main application Static and dynamic seals (standard and special), wipers, O-rings, flange seals, rotary seals, rubber energizers (preload elements). Applications in the food industry. Analysis and Evaluation The mentioned properties are only valid for test pieces of the corresponding ISO, DIN and ASTM standards. They cannot be directly related to seals, gaskets and other sealing products and should be used only as a general guide. C/ Ciclisme 35 Pol. Ind. Can oses. ubí BCN CP 08191 93 588 90 91 www.qyps.es
Silicone B85 FDA BBES Material Data Sheet S103-BL85 Silicone-blue S103 (FDA, peroxide cross linked) S103-BL85 is a blue Methyl Silicone ubber, commonly referred to as Silicone. Silicone materials are often used in hot air and in applications where chemicals and foodstuff are in contact with the sealing material. Because of lower mechanical properties Silicone materials should not be used for dynamic applications. Silicone S103 blue is approved for the use of applications in contact with foodstuff. g/cm3 1,54 Hardness at 20: DIN 53505 Shore A 85 ±5 Tensile strength: DIN 53504 N/mm2 7,4 ±15% Elongation at break: DIN 53504 % 120 ±20% Modulus 100%: DIN 53504 N/mm Tear strength: DIN 53507B N/mm 10 Compression set: 70h/T DIN 53517A % - Compression set: 22h/70 DIN 53517A % - Compression set: 22h/100 DIN 53517A % - Compression set: 22h/175 DIN 53517A % 18,5 ±20% Short time max. service temp. in air: Water up to 90 Fuels Steam below 120 Ozone, Oxygen HFA, HFB, HFC fluids Air up to 200 HFD-, -S Mineral oils S Vegetable oils Silicone oils Key to chemical resistance: = resistant S = suitable = unsuitable Main application Static and dynamic seals (standard and special), wipers, O-rings, flange seals, rotary seals, rubber energizers (preload elements). Due to its low mechanical properties it should be used for static applications only. Chemical and food industry. Analysis and Evaluation The mentioned properties are only valid for testpieces of the corresponding ISO, DIN and ASTM standards. They cannot be directly related to seals, gaskets and other sealing products and should be used only as a general guide. - -55 180 270 C/ Ciclisme 35 Pol. Ind. Can oses. ubí BCN CP 08191 93 588 90 91 www.qyps.es
Silicone 85 FDA BBES Material Data Sheet S102-85 Silicone S102 - red (FDA, peroxide cross linked) S102-85 is a red Methyl Silicone ubber, commonly referred to as Silicone. Silicone materials are often used in hot air and in applications, where chemicals and foodstuff are in contact with the sealing material. Because of lower mechanical properties Silicone materials should not be used for dynamic applications. Silicone S102 red is approved for the use of applications in contact with foodstuff. g/cm3 1,54 Hardness at 20: DIN 53505 Shore A 85 ±5 Tensile strength: DIN 53504 N/mm 2 7,4 ±15% Elongation at break: DIN 53504 % 120 ±20% Modulus 100%: DIN 53504 N/mm - Tear strength: DIN 53507B N/mm 10 Compression set: 70h/T DIN 53517A % 10,8 ±25% Compression set: 22h/70 DIN 53517A % 10,6 ±25% Compression set: 22h/100 DIN 53517A % 6,8 ±25% Compression set: 22h/175 DIN 53517A % 20,4 ±20% 210 Short time max. service temp. in air: 270 Water up to 90 Fuels Steam below 120 Ozone, Oxygen HFA, HFB, HFC fluids Air up to 200 HFD-, -S Mineral oils S Vegetable oils Silicone oils Key to chemical resistance: = resistant S = suitable = unsuitable Main application Static and dynamic seals (standard and special), wipers, O-rings, flange seals, rotary seals, rubber energizers (preload elements). Due to its low mechanical properties it should be used for static applications only. Chemical and food industry. Analysis and Evaluation The mentioned properties are only valid for test pieces of the corresponding ISO, DIN and ASTM standards. They cannot be directly related to seals, gaskets and other sealing products and should be used only as a general guide. -55 C/ Ciclisme 35 Pol. Ind. Can oses. ubí BCN CP 08191 93 588 90 91 www.qyps.es
93 588 90 91 www.qyps.es C/ Ciclisme, 35 Pol. Ind. Can oses. ubí BCN CP 08191 Quality & Precision Sealing FABICACIÓN I DISTIBCIÓN DE JNTAS TODOS LOS DEECHOS ESEVADOS