AKRON TYPE GASKET 485-20 2 50 485-30 3 200 485-40 4 160 485-50 5 485-60 6 AMES For - AMES SBS-Q and SBS-QRD - see FARMLAND, page 6 For - AMES FCR Type see - OVAL GATE AMES ABC-Q TYPE GASKET OD dimension for ref only 480-20 2 50 3" 480-30 3 300 4-1/2" 480-40 4 100 6" 480-50 5 60 7-1/2" 480-60 6 40 9 480-70 7 AMES TYPE SPRINGS - "STANDARD" OD dimension ref only 580-20 2 2-7/8" 580-30 3 4-3/8" 580-40 4 5-3/4" 580-50 5 7-5/16" 580-60 6 8-3/4" AMES LO-HI TYPE GASKET (Replaces AMES FURROW-FLO TYPE) 481-60 6 60 481-70 7 481-80 8 30 481-100 10 25 (10" FURROW-FLO is available for filter applications) 481-120 12 20 481-100SP 10 25 (used in newer lo/hi couplers slightly smaller cross section than origional Ames) AMES ABC-QS TYPE GASKET (Suction and Discharge) 480-60S 6 30 480-80S 8 MUSHROOM DRAIN VALVE (Slow Drain) 495-25 PLAIN 50 Page 59
GASKETS VALVE OPENING ELBOW GASKET 437-07 3/4 437-10 1 AMES GRAVEL TYPE GASKET 482-40G 4 AMES APL TYPE GASKET 482-20P 2 50 482-40P 4 AMES FCR GATE see OVAL GATE, page 45 ANDERSON-MILLER TYPE GASKET (Replaces TELEDYNE, A & M, MILLER-POSTEN) DRAIN 320-20 2 50 320-30 3 300 320-40 4 200 NON-DRAIN 422-20 2 50 422-30 3 250 422-40 4 200 422-45 4.5 422-50 5 110 422-60 6 100 422-70 7 70 422-80 8 75 422-100 10 50 A & M TYPE GASKET RINGLOCK AND SOLID SET 522-30 3 SOLID SET 250 Other sizes available A+M 10" SUPER NON DRAIN (LMC innovative design for a non drip main line) 522-100 10 50 VALVE OPENING ELBOW GASKET 437-06 5/8 437-07 3/4 Page 60
AULT TYPE GASKET (Use RAINMAKER for other sizes) 410-30 3 400 BAUER TYPE BALL & SOCKET COUPLER O-RINGS Description MM / ID 436-20 2" 50 / 2.44" 436-30 3" 76 / 3.48" 436-35 3-1/2" 89 / 4.26" 436-40 4" 108 / 5.20" 436-50 5" 127 / 133 / 5.98" 436-60 6" 152 / 159/ 6.69" 436-80 8" 194 / 8.66" 436-100 10" 11.56" 436-120 12" 300 /... BEN GAR TYPE GASKET 433-60 6 433-70 7 433-80 8 433-100 10 BLUE WAVE TYPE GASKET Also fits Kroy Type plastic coupler 406-30 3 50 CAM-LOCK TYPE FLAT WASHER SEALS 600-07 3/4" 50 600-10 1" 50 600-12 1-1/4" 50 600-15 1-1/2" 50 600-20 2" 50 600-25 2-1/2" 50 600-30 3" 50 600-40 4" 50 600-60 6" 50 600-80 8" 50 (Washers are molded, not die cut) Page 61
GASKETS CHAMPION TYPE GASKET 486-20 2 50 486-21 2 50 for Aluminum Coupler ( outer lip 3/8" high) 486-30 3 180 486-40 4 120 486-50 5 90 486-60 6 60 486-80 8 30 CHAMPION LATCH SPRING 586-00 50 CLOUDBURST TYPE GASKET 458-40 4 458-50 5 458-60 6 75 COBB TYPE GASKET 463-20 2 50 463-30 3 200 463-40 4 100 COMMETCO TYPE GASKET (Replacement for "Commercial Metals Treating Co." galvanized fittings) (Gasket fits over male end of pipe) 432-20 2 432-25 2.5 432-30 3 432-40 4 432-50 5 CROWN AM TYPE GASKET 456-20 2 50 456-30 3 175 456-40 4 125 456-50 5 80 All sizes larger than 5" use Rain for Rent Type 457-xx Larger than 5" use Rain for Rent Type Page 62
DECOTO TYPE SEAL RING (Will fit other style couplings) See THUNDERBIRD 426-06 5/8 VOE 426-40 4 50 426-50 5 50 426-50DL 5 50 Double Lip Wheel Line Gasket DIAMOND / SIMPSON / WATERGATE TYPE GASKET (Above ground - low pressure - plastic pipe) 484-60 6 75 484-80 8 50 484-100 10 50 484-120 12 35 DRAGON TYPE GASKET 425-30 3 200 425-40 4 100 425-50 5 80 425-60 6 60 DRESSER TYPE PIP / OD GASKETS (Also fits ROMAC, BOLT-TITE, WATER-TIGHT and others) 489-20 2 250 Largers sizes available. We mold up 489-30 3 200 to 24.803" PIP gaskets 489-40 4 150 489-50 5 125 489-60 6 80 489-80 8 50 489-100 10 50 489-120 12 40 489-150 15 30 DRESSER TYPE IPS GASKETS 403-30 3.5 200 403-40 4.5 125 403-50 5 90 403-60 6.625 60 403-80 8.625 50 403-100 10.75 35 403-120 12.75 30 Page 63
GASKETS FARMLAND - SBS-Q TYPE GASKET (Very Slow Drain) 470-20 2 50 470-30 3 175 470-40 4 100 470-50 5 60 470-60 6 50 FARMLAND SBS-QRD TYPE GASKET (Non-Drain) "GREEN-DOT" 472-30 3 150 472-40 4 90 472-50 5 50 472-60 6 40 472-80 8 30 FELTON TYPE GASKET (Felco) NON-DRAIN 417-20 2 50 417-30 3 300 417-40 4 200 417-50 5 80 417-60 6 60 5" and larger below 417-70 7 417-80 8 50 417-100 10 40 417-120 12 40 DRAIN GASKETS 317-30 3 250 317-40 4 180 VALVE OPENING ELBOW GASKET 437-06 5/8 See page 11 for pricing FIBERSTRONG TYPE GASKETS 466-80 8 466-100 10 466-120 12 FLEX-O-SEAL TYPE GASKET (Chicago Metal Mfg. Co.) 451-30 3 180 451-40 4 120 451-50 5 60 451-60 6 40 451-80 8 30 Page 64
GHEEN TYPE GASKET (Replacement for LINDSAY, MIDWEST BAND and HOOK, COZAD) 490-20 2 50 490-30 3 200 490-40 4 100 490-50 5 60 490-60 6 50 490-70 7 50 490-80 8 40 490-100 10 30 490-120 12 25 GHEEN DRAIN GASKET (LMC designed) 390-30 3 390-40 4 VALVE OPENER STEM GASKET ( LMC improved designed ) 490-06 5/8 50 490-07 3/4 50 WHEEL LINE FLANGE GASKET Universal design for 4" and 5" flanges x 8 bolt hole 490-05 4"/5" 50 Other sizes available see page 31 GHEEN TRANSITION WATER TIGHT GASKETS HABCO TYPE GASKET 434-50 5 434-60 6 434-80 8 434-100 10 HASTINGS TYPE GASKET (LMC Designed - easier to insert male end into fitting) 424-60 6 60 424-80 8 50 424-100 10 40 424-120 12 40 Page 65
GASKETS IRECO - STEELUME TYPE GASKET 442-15 1-1/2 Trail-Line 50 442-20 2 50 442-30 3 180 442-40 4 125 Drawing below represents 4" and larger 442-50 5 100 442-52 5-1/4 442-60 6 75 442-80 8 50 442-100 10 50 (10" - Heavy duty inner lip) STEELUME TYPE GASKET - OLD STYLE 441-30 3 200 441-40 4 125 441-50 5 90 441-60 6 90 IRECO -DRAIN TYPE GASKET (GO-3D, GO-4D) 342-30 3 225 342-40 4 125 IRECO TYPE SOLID SET GASKET 539-30 180 IRECO TRAIL LINE BUTTON DRAIN D-2-9 395-11 100 IRECO VALVE OPENER BOTTOM GASKET 445-40 4 50 IRECO TYPE VALVE OPENING ELBOW GASKET 437-06 5/8 437-07 3/4 437-10 1 IRECO TYPE "O" RING (Wheel Line applications) 400-43 4-1/2X3/16 50 400-45B 4-3/4X3/16 50 Page 66
IRECO TYPE QUAD RING 404-42 4-7/16X3/16 50 404-59 4-5/8X3/16 50 IRECO A E TYPE GASKET 443-20 2 50 443-30 3 50 443-40 4 50 443-50 5 50 KROY TYPE GASKET Non-Drain [Plastic and Aluminum] 468-60 6 60 468-80 8 50 468-100 10 50 468-120 12 40 MCDOWELL "SAG" TYPE GASKET 446-10 1 (use Rainmaker 409-15) 446-20 2 50 446-30 3 180 446-40 4 120 446-50 5 90 446-60 6 60 446-70 7 446-80 8 446-100 10 MCDOWELL SPRINGS (Gripping Coil) 546-10 1 546-20 2 546-30 3 546-40 4 546-50 5 546-60 6 546-70 7 546-80 8 497-20 McDowell Gate Drill 2" hole in pipe and slip 1.5" pvc or alum. sleeve to act as flow control.--- MCDOWELL MAINLINE and RING LOCK TYPE GASKETS 446-60MG 6 446-80MG 8 446-100MG10 Page 67
GASKETS MID-WEST TYPE GASKETS - See Rain For Rent Type MOORE-RANE TYPE GASKET (Non-Drain) 488-20 2 50 488-30 3 150 488-40 4 100 488-50 5 75 488-60 6 50 488-70 7 40 488-80 8 40 488-100 10 25 488-120 12 MOORE-RANE NARROW TYPE GASKET 388-30 3 DRAIN 300 MOORE-RANE CUB VOE 488-16 1/2x1x1/4 50 488-17 50 488-15 1-1/4-1-1/2 POSILOCK GASKET MOULTON TYPE GASKET 452-20 2 50/400 452-30 3 250 452-40 4 150 452-50 5 452-60 6 75 452-70 7 452-80 8 452-100 10 MOULTON OLD STYLE (thicker cross section) 452-30X 3 452-40X 4 452-50X 5 452-60X 6 Page 68
"O" RING (+++) Recommended for use with FELTON, PORT-ALUM, RAIN CONTROL, SHUR-Rane and others 400-17 1-3/4X1/4 50 400-20 2X3/8 50 +++ See note at top 400-21 2X1/4 50 (2" PORT-ALUM, use 400-21) 400-22 2X3/16 50 400-27 3 X 3/16 50 Yellow PVC Coupler 400-30 3X3/8 50 +++ 400-31 3X3/8 50 (RAINMAKER L-4, use 400-31) 400-32 3-3/8x3/8 50 400-33A 3-5/16x3/16 50 400-33B 3-5/16X3/8 50 400-34 3-7/32X1/4 50 400-35 3-1/2X1/4 50 400-37A 3-7/8X3/16 50 (MOORE-RANE torque coupler) 400-37B 4X3/16 50 400-40 4X3/8 50 +++ See note at top 400-41 4X7/16 50 (RAINMAKER A-4, use 400-41) 400-42A 4-1/8X3/8 50 400-42B 4-1/4X3/16 50 400-42C 4-3/8X3/16 50 400-43 4-1/2X3/16 50 400-44 4-1/2X1/4 50 400-45A 4-5/8X3/16 50 400-45B 4-3/4X3/16 50 400-45C 4-3/4X1/4 50 400-46 4-3/4X1/2 50 O-RINGS ARE MEASURED ON ID AND CROSS SECTION 400-50 5X3/8 50 +++ See note at top 400-51 5X3/8 50 (RAINMAKER, use 400-51) 400-52A 5X1/4 50 400-52B 5-1/4X1/4 50 400-54A 5-3/8X1/4 50 (SHUR-ROLL, use 400-54A) 400-54B 5-1/2X1/4 50 400-60 6X3/8 50 +++ See note at top 400-61 6-1/4X1/4 50 400-65A 6-1/2X5/8 50 400-65B 6-3/8X1/2 50 Yellow Plastic Pipe "O" Rings (CERTAINTEED TYPE) 400-27 3" x 3/16" 1.23 (for use with Certa Set type pipe) 400-662 I.D. 6.625 400-862 I.D. 8.625 400-1075 I.D. 10.75 400-1275 I.D. 12.75 Page 69
OAKS TYPE GASKET 450-40 4 125 450-50 5 450-60 6 100 OLIVER TYPE GASKET 461-20 2 50 newer style 461-30 3 225 461-40 4 160 461-50 5 100 461-60 6 75 461-70 7 50 OVAL GATE ( AMES FCR Type, but slightly improved for easier installation) 497-60 Complete 497-61 Rubber Frame only 497-62 Slide Gate only PACIFIC SPEEDLOCK TYPE GASKET - OLD STYLE (Very first fittings used Round Back ) 462-20 2 50 462-30 3 180 462-40 4 120 462-50 5 90 462-60 6 75 462-80 8 50 PACIFIC SPEEDLOCK TYPE GASKET - NEW STYLE 464-20 2 50 464-30 3 225 464-40 4 150 Page 70
PIERCE TYPE GASKET AND (GENERIC ROUNDBACK COUPLERS) (Replaces AMES QCL, old style A & M, ATLAS, DECOTO, RAINWAY & TICO except 3") 401-13 1-5/16 50 401-20 2 50 401-22 2-1/4 50 401-25 2-1/2 50 401-30 3 200 401-40 4 125 401-50 5 100 401-60 6 70 401-70 7 60 401-80 8 50 401-90 9 401-100 10 30 401-120 12 25 PIERCE TYPE PIVOT GASKET 402-66 6-5/8 70 402-80 8 50 (10" use 407-100) ROUND BACK 3 LIP (non drain) LMC Design Lane round back 3 lip gaskets are designed to seal all brands of round back couplers. Due to many manufacturers making round back fittings they are not all formed the same. The outer 2 lips make up the difference and are superior sealing to a standard round back gasket. 407-30 3 200 407-40 4 125 407-60 6 75 407-80 8 50 407-100 10 30 407-120 12 20 PIERCE "DRAIN" TYPE GASKET 302-30 3 200 302-40 4 125 302-50 5 100 SIDE WHEEL ROLL 400-43 4-1/2X3/16 50 ("O " RING) 400-45B 4-3/4X3/16 50 ("O " RING) 404-45 4-1/2X1/4 50 (QUAD RING) VALVE OPENING ELBOW GASKET 437-06 5/8 See page 11 for pricing 50 437-07 3/4 See page 11 for pricing 50 437-10 1 See page 11 for pricing 50 Page 71
PIERCE TYPE ROUND BACK EPOXY UNDERGROUND GASKET 421-40 4 IPS 125 421-60 6 PIP 90 421-80 8 PIP 60 421-100 10 PIP 30 421-120 12 PIP 25 421-150 15 PIP 20 PORT-ALUM TYPE GASKET 465-20 2 50 465-30 3 200 465-40 4 100 465-50 5 Use SHUR-RANE OLD STYLE 455-50 465-60 6 Use SHUR-RANE OLD STYLE 455-60 RACE & RACE "CONTRACTOR" (CON 6, 7 or 8 on lip) 413-60 6 413-70 7 413-80 8 RACE & RACE "LINKLOK" TYPE GASKET (RACEBUILT) (1" OUTER LIP) 415-20 2 50 415-30 3 180 415-40 4 150 415-50 5 100 415-60 6 60 415-70 7 40 415-80 8 35 RACE & RACE "DEMOUNTABLE" TYPE GASKET (9/16" Outer Lip) 414-20 2 414-30 3 414-40 4 250 414-50 5 150 414-60 6 120 414-80 8 Page 72
RAIN CONTROL TYPE GASKET (HARDIE) 440-20 2 50 2 INCH 440-30 3 150 440-40 4 100 440-50 5 80 440-60 6 50 440-80 8 RAIN FOR RENT TYPE GASKET (WOSCO, LAKE) 457-20 2 50 457-30 3 300 457-40 4 175 457-50 5 457-60 6 75 457-70 7 457-80 8 60 457-100 10 50 457-120 12 40 RAIN FOR RENT "DRAIN" TYPE GASKET 357-30 3 300 VALVE OPENING ELBOW GASKET 437-07 3/4 50 TRAIL LINE BUTTON DRAIN D-2-9 395-11 100 RAIN-OW TYPE GASKET 408-20 2 50 408-30 3 300 408-40 4 200 Page 73
RAINBOW TYPE GASKET (Normal and High Pressure) 418-40 4 125 418-50 5 75 418-60 6 50 418-80 8 30 RAINMAKER TYPE GASKET(Non-Drain) (ARMCO) 409-15 1-1/2 50 409-20 2 50 409-30 3 300 409-40 4 200 409-50 5 100 409-60 6 75 Page 74 RAINWAY SQUARE TYPE GASKET (Non-Drain) 412-20 2 50 412-30 3 300 412-40 4 200 412-50 5 150 412-60 6 100 412-70 7 412-80 8 75 412-100 10 50 412-120 12 50 RAINWAY SUPER NON DRAIN (LMC DESIGN) This gaskets provides near drip proof connections for main line 522-100 10 100 SQUARE O-RING WITH SEALING RIBS FOR BETWEEN MALE / FEMALE 10" Coupler 404-100 RL 10 100 RAINWAY ROUND TYPE GASKET (All other sizes of RAINWAY ROUND, use PIERCE Type or for non-drain use 3-Lip round back) 411-30 3 250 RAINWAY INTERNAL DRAIN TYPE GASKET ( Wheel Line ) 411-45 4.5 50
RAVIT TYPE GASKET 419-20 2 Shape varies by size. Illustration is 2" or 3". 419-30 3 419-40 4 419-50 5 Please specify new or old 419-60 6 style for 5" and 6" gaskets REDI-RAIN TYPE GASKET (Non-Drain) 423-12 1-1/4 Trail-line 50 423-20 2 50 423-30 3 300 423-40 4 160 423-50 5 110 423-60 6 80 423-80 8 75 423-100 10 50 423-120 12 50 DRAIN Gasket 323-30 3 300 REDI-RANE wheel lines 4- bolt couplers use 4" Gasket. Spline couplers use U-Ring or Half O-Ring See wheel line section. REDI-RANE Valve Stems and Valve Discs are now available. Please see page 10. Page 75
SHUR-RANE TYPE GASKET - NEW STYLE (N.S.) (Very Slow Drain) 460-20 2 50 460-30 3 160 460-40 4 100 460-50 5 75 460-60 6 60 460-80 8 50 460-100 10 25 460-120 12 25 SHUR-RANE TYPE GASKET (Non-Drain) (FMC TYPE) 454-30 3 150 454-40 4 110 454-50 5 80 454-60 6 60 454-80 8 50 SHUR-RANE TYPE GASKET - OLD STYLE (O.S.) (Replacement for ROLL-RAIN and VERMEER) 455-20 2 50 455-30 3 160 455-40 4 100 455-50 5 75 455-60 6 50 455-70 7 40 BOLT-ON COUPLER "O" RING - See "O" ring section SHUR-RANE VALVE OPENING ELBOW GASKET 437-03 5/8" SHUR-ROLL DRAIN VALVE (FMC) ( BOLT HOLE IN CENTER) 449-03 4 & 5 "O" RING - use 400-54A Page 76
SNAP-LOCK TYPE GASKET 487-40 4 STOUT TYPE GASKET (Most common style) Measure male end ID of pipe for size (Replacement for ALLUME, T-L and IRECO SPEED ROLL) 444-20 2 200 444-30 3 100 444-40 4 75 444-50 5 50 444-60 6 36 STOUT TYPE GASKET (Very old style) Measure male end ID of pipe for size 447-20 2 200 447-30 3 100 447-40 4 75 447-50 5 50 447-60 6 36 STOUT SEAL RING 445-20 2 50 445-30 3 50 445-40 4 50 445-50 5 50 445-60 6 50 STOUT, OLD STYLE ALUMINUM FITTING 476-20 2 50 476-30 3 50 476-40 4 50 476-50 5 50 476-60 6 50 STOUT TOWLINE SEAL RING 478-40 3.5 50 478-50 4.5 50 Page 77
STROLYTE TYPE GASKET 435-20 2 50 435-30 3 200 435-40 4 110 435-50 5 100 435-60 6 75 THUNDERBIRD TYPE WHEEL LINE GASKET LMC designed (426-TB pictured. For 439-40 picture see Western type. This is used for current model TB wheel lines.) 426-40TB 4 50 439-40 4 110 TRI-MATIC TYPE GASKET 405-15 1.5 405-70 7 MUSHROOM DRAIN VALVE (Fast Drain) 495-15 KNOBBY 1.30 VICTAULIC TYPE GASKET (Industrial Grooved Fittings) 471-20 2 200 (Irrigation or drainage use 471-30 3 150 only - not for petroleum.) 471-40 4 75 471-60 6 50 471-80 8 35 471-100 10 25 471-120 12 20 WADE TYPE GASKET (Normal Slow Drain) 428-20 2 50 428-30 3 350 428-40 4 200 428-50 5 150 428-60 6 100 428-70 7 100 428-80 8 80 428-100 10 (Non-drain) 75 Page 78
WADE POWEROLL TYPE GASKET (Fast Drain) 430-40 4 200 430-45 4.5 200 430-50 5 120 WADE "J" TYPE GASKET (For bolt-on couplers) 431-15 1.5 431-20 2 431-30 3 431-40 4 WADE OLD STYLE FLAT TYPE GASKET 429-20 2 429-30 3 429-40 4 STAR DRAIN 427-03 WEBSTER ECONOMIZER TYPE GASKET 416-01 3/4 416-20 2 50 416-30 3 225 416-40 4 160 416-50 5 100 416-60 6 75 416-70 7 416-80 8 WEBSTER TRIGGER LOCK TYPE GASKET 453-30 3 3" pictured 453-40 4 4" and larger are 453-50 5 different shape. 453-60 6 453-70 7 453-80 8 Page 79
WESTERN TYPE GASKET 439-20 2 50 439-30 3 200 439-40 4 110 439-50 5 100 439-60 6 75 439-70 7 50 439-80 8 50 439-100 10 40 (10" & 12" - Heavy duty inner lip) 439-120 12 25 VALVE OPENING ELBOW GASKET 437-07 3/4 WHEEL TRAC TYPE GASKET - Manufactured to order 467-20 2 467-30 3 467-40 4 WYSS TYPE GASKET (Replaces CROWN, MONTGOMERY WARD, STOUTBILT ALUM. & others) 475-20 2 50 475-30 3 200 475-40 4 100 475-50 5 80 475-60 6 50 WYSS SEAL RING 476-20 2 50 476-30 3 50 476-40 4 50 476-50 5 50 476-60 6 50 WYSS VALVE DISK COVER 497-01 4 Page 80