MAGNETIC SUPPLY INSTALLATION SAFETY GUIDE Please read before installing. GENERAL This power supply is to be installed in accordance with Article 450 of the National Electric Code. The power supply must be installed in a well ventilated area free from explosive gasses and vapors. Proper operation requires the free flow of air. Because this power supply is hardwired, installation should only be performed by a qualified electrician. BEFORE INSTALLING Check the label and ensure the power supply has the proper input voltage, output voltage and wattage for the job. Check the wire markings to ensure they match the wiring diagram shown (bottom-left) on this guide. MOUNTING Select a suitable location capable of supporting the weight of the power supply. Use the two keyholes in the transformer case. It is recommended that the power supply be mounted vertically with the wiring compartment pointing down. Maintain 6 inches between drivers. INPUT CONNECTIONS / GROUNDING Remove the wiring compartment knockouts and install strain reliefs. With power turned off, route the input wires through a strain relief and connect one wire to black and one wire to white. For all wire connections, use only UL listed wire nuts and connectors of suitable size and type. The transformer case MUST be grounded in accordance with the N.E.C. Connect the ground wire to the transformer green wire. OUTPUT CONNECTIONS Bring the wires of the light fixture through the other open knockout and connect them to the power supply output wires. DIMMING ONLY use a low-voltage magnetic dimmer that is compatible with our magnetic LED power supplies. See the Dimming Guide at the end of this document for more info. WIRING DIAGRAM L N AC POWER L (Black) N (White) L N G V- V+ V+ (Red to Red) V- (Blue to Black) STOP MUST HAVE MINIMUM OF 50% WATTAGE IF NOT DIMMING. OPTIMAL OPERATING RANGE IS 50-85% OF DRIVER WATTAGE
MAGNETIC POWER SUPPLIES / 10 WATT SPECIFICATIONS NF-PS-TM10W12V NF-PS-TM10W24V 120VAC Output Voltage 12V 24V Rated Power Maximum Input Current Max Operating Temperature Insulation System Input Leads Output Leads 10W 1A 131 F / 55 C 18 AWG 12 AWG Lead Insulation 221 F / 105 C Reset Breakers 0.8A on primary, 1.5A on secondary 0.8A on primary and secondary Dimmability Safety Housing Magnetic Low Voltage (MLV) Class 2, ETL/CSA Listed, Nema 3R Black powder coated steel enclosure Dimensions (L*W*H) 6.03 * 1.9 * 1.43 1.7 lbs 1.9 lbs 1.9 1.43 6.03
MAGNETIC POWER SUPPLIES / 20 WATT SPECIFICATIONS NF-PS-M20L12V NF-PS-M20L24V Max Load 20W 120V AC Input Current Full Load 310mA 270 ma Output Voltage Full Load 11V DC 21.89V DC Max Output Current Full Load 1.9A 0.97A Open Circuit Output Voltage 11.8V DC 23.2V DC Average Efficiency 74% 76% Power Factor on l 0.81 0.92 Coil Former Thermal Class Double Section Bobbin Leads Primary PVC 600 V#20 Leads Secondary PVC 300 V#16 Circuit Breaker Primary and Secondary Auto-Reset Safety Standards Nema 3R, Class 2, ETL Listed, Conforms to UL 8750 Dimensions (L*W*H) 5.6 * 2 * 2.14 2.2 lbs 5.6 2 2.14
MAGNETIC POWER SUPPLIES / 40 WATT SPECIFICATIONS NF-PS-M40L12V NF-PS-M40L24V Max Load 40W 120V AC Input Current Full Load 510mA 410 ma Output Voltage Full Load 11.1V DC 22.3V DC Max Output Current Full Load 3.96A 1.72A Open Circuit Output Voltage 12.2V DC 24.5V DC Average Efficiency 79% 82% Power Factor on l 0.88 0.89 Coil Former Thermal Class Double Section Bobbin Leads Primary PVC 600 V#20 Leads Secondary PVC 300 V#16 Circuit Breaker Primary and Secondary Auto-Reset Safety Standards Nema 3R, Class 2, ETL Listed, Conforms to UL 8750 Dimensions (L*W*H) 5.6 * 2 * 2.14 2.2 lbs 5.6 2 2.14
MAGNETIC POWER SUPPLIES / 60 WATT SPECIFICATIONS NF-PS-M60L12V NF-PS-M60L24V Max Load 60W 120V AC Input Current Full Load 760 ma 0.95 A Output Voltage Full Load 10.8V DC 22.2V DC Max Output Current Full Load 5.9A 2.56A Open Circuit Output Voltage 11.9V DC 23.8V DC Average Efficiency 80% 85% Power Factor on l 0.84 0.82 Coil Former Thermal Class Double Section Bobbin Leads Primary PVC 600 V#20 Leads Secondary PVC 300 V#16 Circuit Breaker Primary and Secondary Auto-Reset Safety Standards Nema 3R, Class 2, ETL Listed, Conforms to UL 8750 Dimensions (L*W*H) 6.55 * 2.25 * 2.55 2.2 lbs 6.5 2.25 2.55
MAGNETIC POWER SUPPLIES / 75 WATT SPECIFICATIONS Output Voltage Rated Power NF-PS-TM75W24V 120VAC 24V 75W Maximum No Load Input Current 0.2A Max Operating Temperature 149 F / 65 C Insulation System Input Leads Output Leads 18 AWG 12 AWG Lead Insulation 221 F / 105 C Reset Breakers Dimmability 5A on secondary side Magnetic Low Voltage (MLV) Safety Class 2, ETL/CSA Listed, Nema 3 Housing Black powder coated steel enclosure 4.15 lbs Dimensions (L*W*H) 7.5 * 3.1 * 2.9 2.2 lbs 7.5 2.9 3.1
MAGNETIC POWER SUPPLIES / 100 WATT SPECIFICATIONS Output Voltage Rated Power Maximum Input Current NF-PS-TM100W12V 120VAC 12V 100W - 2 x 50W circuits 2A Max Operating Temperature 131 F / 55 C Insulation System Input Leads Output Leads 18 AWG 12 AWG Lead Insulation 221 F / 105 C Reset Breakers Dimmability Safety Housing 3A on primary, 2 x 4A on secondary Magnetic Low Voltage (MLV) Class 2, ETL/CSA Listed, Nema 3R Black powder coated steel enclosure Dimensions (L*W*H) 7 * 7 * 3.2 8.4 lbs 7 7 3.2
MAGNETIC POWER SUPPLIES / 100 WATT SPECIFICATIONS Output Voltage Rated Power Maximum Input Current NF-PS-TM100W24V 120VAC 24V 100W - 1 x 100W circuits 1A Max Operating Temperature 149 F / 65 C Insulation System Input Leads Output Leads 18 AWG 12 AWG Lead Insulation 221 F / 105 C Reset Breakers Dimmability Safety Housing 2A on primary, 7A on secondary Magnetic Low Voltage (MLV) Class 2, ETL/CSA Listed, Nema 3R Black powder coated steel enclosure Dimensions (L*W*H) 7.5 * 3.2 * 2.9 5.1 lbs 7.5 2.94 3.22
MAGNETIC POWER SUPPLIES / 120 WATT SPECIFICATIONS Max Load Input Current Full Load Output Voltage Full Load NF-PS-M120L12V 120W - 2 x 60W Circuits 120V AC 1.5 A 11.3V DC Max Output Current Full Load 5.9A Open Circuit Output Voltage 12.8V Efficiency on I 80% Power Factor 0.93 Coil Former Thermal Class Double Section Bobbin Leads Primary PVC 600V #20 Leads Secondary PVC 300V #14 Circuit Breaker Auto-reset Dimensions (L*W*H) 9.8 * 4.2 * 3.2 8.75 lbs 9.8 4.2 3.2
MAGNETIC POWER SUPPLIES / 180 WATT SPECIFICATIONS Max Load Input Current Full Load Output Voltage Full Load NF-PS-M180L12V 180W - 3 x 60W Circuits 120V AC 2.1 A 11.3V DC Max Output Current Full Load 5.9A Open Circuit Output Voltage 12.8V Efficiency on I 87% Power Factor 0.92 Coil Former Thermal Class Double Section Bobbin Leads Primary PVC 600V #20 Leads Secondary PVC 300V #14 Circuit Breaker Auto-reset Dimensions (L*W*H) 9.8 * 4.2 * 3.2 8.75 lbs 9.8 4.2 3.2
MAGNETIC POWER SUPPLIES / 192 WATT SPECIFICATIONS Max Load Input Current Full Load Output Voltage Full Load NF-PS-M192L24V 192W - 2 x 96W Circuits 120V AC 2.1 A 11.3V DC Max Output Current Full Load 5.9A Open Circuit Output Voltage 12.8V Efficiency on I 87% Power Factor 0.92 Coil Former Thermal Class Double Section Bobbin Leads Primary PVC 600V #20 Leads Secondary PVC 300V #14 Circuit Breaker Auto-reset Dimensions (L*W*H) 9.8 * 4.2 * 3.2 8.75 lbs 9.8 4.2 3.2
MAGNETIC POWER SUPPLIES / 200 WATT SPECIFICATIONS NF-PS-TM200W12V NF-PS-TM200W24V 120VAC Output Voltage 12V 24V Rated Power 200W - 4 x 50W Circuits 200W - 2 x 100W Circuits Maximum Input Current 0.6A 0.4A Max Operating Temperature 158 F / 70 C Insulation System Input Leads Output Leads 18 AWG 12 AWG Lead Insulation 221 F / 105 C Reset Breakers 3A on primary, 6 x 5A on secondary 2A on primary, 4A on secondary Dimmability Safety Housing Magnetic Low Voltage (MLV) Class 2, ETL/CSA Listed, Nema 3R Black powder coated steel enclosure Dimensions (L*W*H) 7 * 7 * 3.2 8.7 lbs 8.5 lbs 7 7 3.2
MAGNETIC POWER SUPPLIES / 288 WATT SPECIFICATIONS Max Load NF-PS-M288L24V 288W - 3 x 96W Circuits 120V AC Input Current Full Load 3.4A Output Voltage Full Load 22.1V DC Max Output Current Full Load 4.31A Open Circuit Output Voltage 24.5V DC Efficiency on I 84% Power Factor 0.9 Coil Former Thermal Class Double Section Bobbin Leads Primary PVC 600V #20 Leads Secondary PVC 300V #14 Circuit Breaker Auto Reset Dimensions (L*W*H) 9.8 * 4.2 * 3.2 8.75 lbs 9.8 4.2 3.2
MAGNETIC POWER SUPPLIES / 300 WATT SPECIFICATIONS Max Load Input Current Full Load Output Voltage Full Load Max Output Current Full Load Open Circuit Output Voltage NF-PS-M300L12V 300W - 5 x 60W Circuits 120V AC 2.86 A 11.3V DC 5.9 A on each port 12.8V DC Efficiency on I 78% Power Factor 0.93 Coil Former Thermal Class Double Section Bobbin Leads Primary PVC 600V #20 Leads Secondary PVC 300V #14 Circuit Breaker Auto Reset Dimensions (L*W*H) 9.8 * 4.2 * 3.2 8.75 lbs 9.8 4.2 3.2
MAGNETIC POWER SUPPLIES / 300 WATT SPECIFICATIONS NF-PS-TM300W12V NF-PS-TM300W24V 120VAC Output Voltage 12V 24V Rated Power 300W - 6 x 50W Circuits 300W - 3 x 100W Circuits Maximum Input Current 0.6A 0.6A Max Operating Temperature 158 F / 70 C Insulation System Input Leads Output Leads 18 AWG 12 AWG Lead Insulation 221 F / 105 C Reset Breakers 3A on primary, 6 x 5A on secondary 3A on primary, 6 x 4A on secondary Dimmability Safety Housing Magnetic Low Voltage (MLV) Class 2, ETL/CSA Listed, Nema 3R Black powder coated steel enclosure Dimensions (L*W*H) 7 * 7 * 3.2 8.5 lbs 7 7 3.2
MAGNETIC POWER SUPPLY INSTALLATION & DIMMING GUIDE Please read before installing. ONLY USE A LOW-VOLTAGE MAGNETIC DIMMER THAT IS COMPATIBLE WITH OUR MAGNETIC LED POWER SUPPLIES AC POWER L N G V- V+ V+ (Red to Red) L N L (Black) N (White) V- (Blue to Black) DIMMERS The following magnetic low-voltage analog dimmers are compatible with our magnetic LED power supplies. Note: Some magnetic dimmers require a minimum/maximum load. Please check the specs of the dimmer you are planning to use before installing. LUTRON ARIADNI DIMMER AYLV-600P AYLV-600P-CSA AYLV-600P-S AYLV-603P AYLV-603P-CSA AYLV-603P-S LUTRON DIVA DIMMER DVLV-10P DVLV-103P DVLV-600P DVLV-10P-CSA DVLV-103P-CSA DVLV-603P NOVA FLEX RECOMMENDS: DVLV-600, DVLV-603P DVLV-10P-S DVLV-103P-S DVLV-603P-CSA DVLV-10PH-S DVLV-103PH-S DVLV-603P-S DVLV-603PH-S