Square 1 ir Cylinders age General Standard Ratings and Sizing Guide.... Construction Details....,. How a Square 1 is built Standard Specifications....5 odel Number Codes....6 Option ist....6 How to Order....6 Standard Specifications (Dimension Details)....7,.8 Option Specifications....9 -.1 Description and Dimensions of the Options ounting Kits for SQ and SQW lange ounting Kits....1 Trunnion ounting Kits....15 Clevis racket Kits....15 ye racket Kits....15 Clevises....15 ccessories low Controls, ort ounted and Others... Section 1 osition Sensors.... ounting olts... Section 1.16 Wrench lat Wrench... Section 1.16 ir Spring Return... Section 1.15 ear Warranty... Inside back cover.1 7--01
Square 1 Cylinders vailable in styles 5 ore sizes /" thru " Strokes to 6" Hard chrome plated stainless steel piston rod iston ushing, hard anodized aluminum housing with Teflon lined Duralon insert T earing Strip, for stroke 1" and over, is located away from rod bearing for maximum load support iston Seal, internally lubricated O'Ring for long life and improved performance Heavy wall construction, hard anodized inside and out Crosshatch polished bore for lubrication retention and longer seal life Series SQ, Side Tap ount Side view (opposite ports) shows mounting holes and relief for mounting rails. Series SQ, ace ount Series SQ, Side ug ount Duralon earings xcel oad Capacity (psi) riction roperties achine Design 197/7 Slip- earing Reference Issue Coefficient stick orous ronze...,500 Steel-on-steel... es orous iron... 8,000 ronze-on-steel....5 es henolics... 6,000 Sintered ronze-on-steel Nylon... 1,000 with mineral oil.... No T... 500 ronze-on-steel Reinforced Telfon...,500 with mineral oil....16 No *T fabric... 60,000 Copper lead alloy-on-steel es olycarbonate... 1,000 cetal-on-steel....0 No cetal... 1,000 Nylon-on-steel.... es Carbon-graphite... 600 Duralon-on-steel....05 -.16 No * Shows Duralon bearing classification. Not to be used for design purposes. rinted with permission by Rexnord Corp. Ratings Standard Units all series Double acting, single rod Duralon rod bushing emale rod end with wrench flats Internally lubricated una-n O-ring piston and rod seals. orts at position #1 edia.................... ir, Optional Hydraulic ax. operating pressure...... 150 psi ir or Hydraulic in. operating pressure recommended....... 10 psi mbient & media temperature range.. -5 to +50 relubrication.............. agnalube G Grease ir ine ubrication................ Recommended Stroke tolerance......................... ± 1/6" 7--01 Sizing Guide ore Diameter /" 7/8" 1-1/8" 1-5/8" " Diameter 05 05 00 0.65 00 rea 0.08 0.08 0 0 0. ush rea (Single ) 0. 0.60 0.99.07.1 ull rea 0.6 0.5 0.80 1.76.70 SQ & SQ ase Weight, lb. 0.18 0 0 1.05 SQ ase Weight, lb. 0.18 0. 0.70 1.16 Weight er Inch, lb. 0. 0. 0 0. 0.5.
Square 1 Cylinders Strokes under 1" Standard Single odels Shown Double : See Option -DR page.10 Nonrotating: See Option -K page.1 Strokes 1" and over 10 9 6 6 10 1 9 6 6 11 1 5 11 5 8 7 6 /", 7/8" 1-1/8", 1-5/8" ores 8 " ore 6 owed 7 Rectangular 8 7 Rectangular eveled Series SQ Series SQ Series SQ 5 5 5 1 1. 7-17-01
Construction Details 1 The square body material is a custom aluminum extrusion with a relief extruded in to provide mounting rails. The SQ series extrusion includes the body side extensions for the Side ug ounting. These mounting rails are machined flat before any other machining is done. This step eliminates any twist or curl in the rails, assuring a flat mounting surface. Note: the SQ 0 and SQ 0 (/" bore) are produced from standard square bar stock. The cylinder body is located on fixture points ( ) while the cylinder bore is machined. This provides an accurate and consistent dimension from the bore centerline to the mounting surface for mounting the cylinder and making attachments to the piston rod. The ace ount, Series SQ and SQW, mounting holes are machined in relationship to the centerline of the bore to control the accuracy and consistency for mounting and making attachments to the rod. The cylinder bore is polished to produce a fine crosshatch finish, which, unlike an ultra smooth finish, provides a reservoir for lubrication. ubrication, of course, provides lower friction and longer seal life. 5 The cylinder is hard anodized inside and out. This is an electrochemical process which provides a very dense surface of aluminum oxide. This surface has extreme hardness (60 Rc), excellent wear and corrosion resistance, and low coefficient of friction. The hard anodizing actually impregnates the base aluminum rather than just coating the surface like a plating. The hardness and wear resistance exceed that of hard chrome plated steel. The appearance is an attractive, satin gray. 6 Unique construction provides unequaled piston rod support and prohibits rod bushing OWOUT! The onepiece Duralon rod bushing is inserted from the inside and then staked in place. Duralon is a Teflon lined, fiberglass structure with load carrying capacity of 60,000 psi. See the chart comparing this to other bearing materials on page.. Duralon also provides: consistency- reliable and predictable performance from bushing to bushing; corrosion resistance- nonmetallic materials resist galvanic, chemical, and fretting corrosion; self lubrication- Teflon lining provides low friction and minimizes slipstick, even under no-load conditions; seizure resistancefiberglass backing material will not seize or gall on shaft under extreme wear. bearing length on 1" stroke and over is longer to provide additional load support at the longer extensions. The O'Ring seal is located outboard as far as possible to allow air system lubrication onto most of the bearing surface. 7 The rod bearings and cap end plugs are held in place by two internal lockrings. In the " (1) bore size the inboard lockring and its groove are of standard rectangular cross section. The outboard lockring and its groove are beveled. s the outboard lockring expands in this beveled arrangement, it drives the rod bearing or cap end plug into and tightly against the inboard lockring. This locks the bearing or plug rigidly in place, thus providing precision, non-floating location and rigid support for the piston rod. 8 The rod bearings and cap end plugs are held in place by two internal lockrings. In bore sizes /" (0) thru 1-5/8" (1) all the lockring grooves are of standard rectangular cross section. The internal groove is wider and the lockring is bowed. This bowed lockring drives the rod bearing or cap end plug tightly against the outboard lockring, thus providing precision, non-floating location and rigid support for the piston rod. 9 The piston rod is centerless ground, polished and hard chrome plated (68-7 Rc) stainless steel. Surface finish is 1 RS or better and carries lubrication like our cylinder bore (see ). These features, combined with the low friction and high load capacity of the Duralon bushing provide exceptional cylinder life. emale, fine pitch rod thread and wrench flats are standard. 10 Cylinders with strokes under 1" have a thin piston head with a single O'Ring for space savings. Cylinders with 1" stroke and over have a thicker piston which incorporates a T bearing in addition to the O'Ring seal. This bearing is a close tolerance, rectangular cross section strip of a tough, stable, wear resistant T compound located at the rear of the piston head, the furthest point from the rod bearing. The bearing material and its location provide maximum load support and maintain the long life of the cylinder bore and piston seal. 11 The piston is aluminum for light weight. It has a counterbore which locates the piston rod and provides precise concentricity control for smooth cylinder movement. 1 The piston is attached to the piston rod with a socket flat head screw which is torqued for both proper preload on the screw and secure clamping of the piston. octite on the threads and faces assures sealing and locks the assembly against pounding and vibration. Internally lubricated una-n O'Rings (5 to + 50 ) provide low profile, low friction, and long life sealing of the piston and rod. These are compounded to provide extra long wear and low breakaway (starting) pressure, running friction and smoother operation. In tests, cylinders with internally lubricated O'Rings have extended cycle life of to times beyond cylinders with standard una-n seals. 7-17-01.
Standard Specifications Side Tap ounting: Series SQ odel SQ 11- Side view (opposite ports) shows mounting holes and relief for mounting rails. ore Series vailable Stroke engths (Inches) 1/8 1/ 1/ / 1 1-1 / 5 6 /" SQ0 1-1/8" SQ11 1-5/8" SQ1 " SQ1 agnetic piston option does NOT affect stroke. ace ounting: Series SQ odel SQ 11- ore Series vailable Stroke engths (Inches) 1/8 1/ 1/ / 1 1-1 / 5 6 /" SQ0 1-1/8" SQ 11 1-5/8" SQ 1 " SQ 1 agnetic piston option does NOT affect stroke. Side ug ounting: Series SQ ore Series vailable Stroke engths (Inches) 1/8 1/ 1/ / 1 1-1 / 5 6 7/8" SQ06 1-1/8" SQ 11 1-5/8" SQ 1 " SQ 1 odel SQ 11- ll Square 1 ountings Double cting Single Choice of "G" or "W" xtension* or single acting use air spring as shown on page 1.15 Double cting Double Choice of combinations of "G" and "W" rod extensions* emale nd with Wrench lats T iston earing; 1" Stroke and Up Internally lubricated una-n Seals (-5 to + 50 ) Operation to 150 psi and Cap nd orts in osition 1 agnetic piston option does NOT affect stroke. CD Drawings on CD-RO complete library of cylinder CD drawings is available. Contact your local distributor for details, download from our web site http://www.fabco-air.com or -ail us at fabco@fabco-air.com *or xtension Information See Dimension "G" and "W" on pages.6,.7 or.8..5 7--01
How To Order SQ odel Number Code 11 R ounting SQ Side Tap SQ ace SQ Side ug xtension Single odels lank for standard extension per dimension "G" on page.7 W - for xtension to dimension "W" on page.7 Double odels See age.10 lank "G" extension both ends W "W" extension both ends GW "G" extension on rod end; "W" extension on cap end WG "W" extension on rod end; "G" extension on cap end ore 0 for /" bore 06 for 7/8" bore 11 for 1 1/8" bore 1 for 1-5/8" bore 1 for " bore Standard Strokes Inches ores /" 7/8" 1/8 1/ 1/ / 1 1-1/ ores 1-1/8" 1-5/8" " 1/8 1/ 1/ / 1 1-1/ 5 6 How to Order 1. Specify ounting Series including xtension Information. Specify ore. Specify Stroke in Inches and ractions. Specify Options xamples SQ 11 - Side Tap ounting with "G" xtension; 1-1/8" ore; " Stroke SQW 11 - - R Side Tap ounting with "W" xtension; 1-1/8" ore; " Stroke; ale Thread SQW 06 - - C - R Side ug ounting with "W" xtension; 7/8" ore; " Stroke with 1/" Stroke Collar yielding -/" Net Stroke; Sound imiter, Cap nd OTIONS Description Specify See age ale Thread.9 Single -R Double, nd -R Double, Cap nd -R1 Double, oth nds -R Viton Seals (-15 to +00 ) -V.9 Quad Seals -Q.9 etric Thread -.9 Nonrotating -K.1 1-1/8", 1-5/8", " bores only ort ositions -1.9 xternal Guide, Nonrotating -G.1 Hydraulic, ow ressure -H.9 to 150 psi NONSHOCK Double -DR.10 Hole Thru Double Shaft.10 ore Hole /", 7/8" 1/16" -DR06 1-1/8" 1/8" -DR lus size 5/" -DR16 1-5/8" 1/8" -DR lus size 1/" -DR5 " 5/" -DR16 lus size 5/16" -DR1 Stroke Collar 1/8" C1.11 1/" C /8" C 1/" C 5/8" C5 /" C6 7/8" C7 Sound imiters.11 nd - Cap nd -R oth nds -R djustable Retract Stroke -RS.11 or over 1" adjustment add desired length: e.g. -RS agnetic iston & mounting slot(s). for iston osition Sensors - (Order Sensors separately.) ounting Kits for Series SQ Type See age lange ount Kit.1 Trunnion ount Kit.15 Clevis racket Kit.15 ye racket Kit.15 Clevis.15 7--01.6
Square 1 Cylinders SQ Series: Side Tap ounting /", 1-1/8", 1-5/8" and " ores + Stroke ort osition ort Z + Stroke 1 osition X 1 H G or W G or W 1 + Stroke Z + Stroke K1 K1 (Ref.) Cylinders with less than 1" stroke have mounting holes N1 nd ace + Stroke Cap nd ace N1 Cylinders with 1" stroke or more have mounting holes SQ Series: Side ug ounting 7/8", 1-1/8", 1-5/8" and " ores ort osition 1 H Washer Supplied with cylinder for use under mounting bolt head to prevent cylinder movement while tightening bolt T (Ref.) K 1 X K ort osition 1 G or W S (Ref.) + Stroke Z + Stroke N Cylinders with less than 1" stroke have mounting holes G or W nd ace + Stroke Z + Stroke + Stroke Cylinders with 1" stroke or more have mounting holes N ixed Dimensions ore /" 7/8" 1-1/8" 1-5/8" " 1.5 1.5 1.00 Dia..6 G.. H 1/ 1/ 7/16 1/ 5/8.5.5 K1 1. 1.00 K 1 1.00 N1 10-x.5 10-x.5 1/-0x 5/16-18x N.1.1.7.7 10-10- 1/8 1/8 1/8 R.5.5 S1 1. 1.00 S.5 T1 1/-0 xdp (Note ) 1/-0 xdp (Note ) 1/-0 xdp (Note ) 5/16-18 xdp (Note ) T.0.0.0.0 U W X.8.7 7-6-01
Dimensions SQ Series: ace ounting /", 1-1/8", 1-5/8" and " ores igure 1 nd View igure Side View Short Strokes igure Side View ong Strokes ort osition 1 (see note) H 1 X ort osition 1 G or W + Stroke Z + Stroke G or W + Stroke Z + Stroke S1 S1 R (Ref.) S1 S1 "T1" (see note) R (Ref.) U nd ace U Cap nd ace Note 1 T1 Tapped mounting holes, each end. When port position 1 is specified, mounting holes T1 rotate 90. Note /", 1-1/8", and 1-5/8" ores, 1/8" thru 1" Strokes only:.0 Dia. thru,. dia. C'ore x deep for #10 SHCS and 1/-0 x deep tapped mounting holes, places each end. Note " ore, 1/8" thru 1-1/" Strokes only:.7 Dia. thru, dia. C'ore x.6 deep for 1/" SHCS and 5/16-18 x deep tapped mounting holes, places each end. Variable Dimensions Stroke 1/8" 1/" 1/" /" 1" 1-1/" " " " 5" 6" 1.0 1.0 1.0 1.0 1.7 1.7 1.7 1.7 1.7 /" & 7/8" ores 1-1/8" ore 1-5/8" ore " ore 10- x 10- x 10- x 10- x 10- x 10- x 10- x 10- x 10- x.58.6.76.89.51.51.51.51.51.5.5.5.5.5 Z.5.5.5.5.9.9.9.9.9 1.8 1.8 1.8 1.8 1.68 1.68 1.68 1.68 1.68 1.68 1.68 5/16-x. 5/16-x 5/16-x 5/16-x 5/16-x 5/16-x 5/16-x 5/16-x 5/16-x 5/16-x 5/16-x.70.77.89 1.01.59.59.59.59.59.59.59. Z.1.8.8.8 1.57 1.57 1.57 1.57 1.9 1.9 1.9 1.9 1.9 1.9 1.9 /8-x /8-x /8-x /8-x /8-x /8-x /8-x /8-x /8-x /8-x /8-x.85.91 1.0 1.16.66.66.66.66.66.66.66 Z 1.7 1.7 1.7 1.7.11.11.11.11.11.11.11 1/-0x 1/-0x.56 1/-0x 1/-0x 1/-0x 1/-0x 1/-0x 1/-0x 1/-0x 1/-0x 1/-0x.9.99 1.1 1..68.68.68.68.68.68.68.6.6.6.6.6.6.6.6.6.6.6 Z 7-6-01.8
Square 1 Cylinders ale Thread Single Double, nd Only Double, Cap nd Only Single, oth nds octite Stud No Relief No weakness Option -R -R -R1 -R high strength stud is threaded into the standard female rod end and retained with octite. This method eliminates the small diameter thread relief area normally Thread required when machining male threads. It provides a much stronger rod end which can be repaired, rather than replacing the complete rod, should the thread be damaged. ore Thread /" 10- x 0 7/8" 10- x 0 1-1/8" 5/16- x 0 1-5/8" /8- x 0 " 1/-0 x Viton Seals Option -V or elevated temperatures (15 to +00 ) or compatibility with exotic media. Consult engineering for compatibility information. Quad Seals Option -Q QUD seal replaces the standard O'Ring on the piston only. Standard seal material is una-n with operating temperatures of 5 to + 50. Consult engineering for other materials. etric Thread Option - See page.15 for etric Clevis threads are configured in common TRIC sizes. To arrive at emale Thread depth in mm, multiply nglish depth by 5.. See page.15 for etric Clevis. ore emale Thread itch ale Thread x ength / 5 0.8 5 x 1.7 7/8 5 0.8 5 x 1.7 1-1/8 8 1.5 8 x 19.0 1-5/8 10 1 10 x. 1 1 1 x 5. orts osition Option -1 oth ports are located at osition 1 (see drawings on page.7). This position is achieved by reverse assembly of the cylinder. Therefore, it is a no-charge option. lease note that on Series SQ and SQW the mounting holes rotate 90. orts can be located in other positions on a special basis. Consult engineering with application requirements for details on other locations. Hydraulic Option -H ow pressure service to 150psi NONSHOCK or ir-over-oil or Hydraulic systems to 150 psi, NONSHOCK. Where space permits, a U-cup rod seal or an additional rod O'Ring is incorporated in the rod bearing to help prevent fluid carry-over past the rod seal..9 7-17-01
Option Specifications Double iston SQ...... -DR SQW.... -DR SQGW... -DR SQWG... -DR SQ..... -DR SQW... -DR SQGW.. -DR SQWG.. -DR SQ..... -DR SQW... -DR SQGW.. -DR SQWG.. -DR Counterbores Option -DR Stud "G" rod ext. both ends. "W" rod ext. both ends. "G" rod ext. rod end; "W" rod ext. cap end. "W" rod ext. rod end; "G" rod ext. cap end. "G" rod ext. both ends. "W" rod ext. both ends. "G" rod ext. rod end; "W" rod ext. cap end. "W" rod ext. rod end; "G" rod ext. cap end. "G" rod ext. both ends. "W" rod ext. both ends. "G" rod ext. rod end; "W" rod ext. cap end. "W" rod ext. rod end; "G" rod ext. cap end. Standard piston rod and rod bushing on both ends of the cylinder. Counterbores on both sides of the piston maintain concentricity of the piston rods to each other as well as to the piston O-ring. The piston rods are connected by a high strength stud, sandwiching the piston between the rod faces. The assembly is torqued for proper preload of the stud and clamping of the piston head. octite on the threads and faces assures sealing and locks the assembly against pounding and vi- G or W nd Single odels lank for standard extension per dimension "G". W for extension to dimension "W". xtension Dimensions ore /" 7 /8" 1-1 /8" 1-5 /8" " G.. W bration. This procedure provides a positive and rigid assembly that will not allow the piston rod to float or be pounded loose. The T piston bearing is not required because the two rod bushings provide excellent piston support. Use when attachment to both ends of the cylinder is required or to indicate piston position. The availability of rod extensions offers a number of model combinations as shown in the listings at the left. G or W + Stroke Cap nd Double odels lank "G" both ends. W "W" extension both ends. GW "G" extension rod end; "W" extension cap end. WG "W" extension rod end; "G" extension cap end. Note: When using stroke collars in double rod units, C ND ROD STICK-OUT increases by amount stroke is shortened. Hole Thru Double Shaft hole is drilled through the piston rods and the double rod stud. This hole is used for the passage of Vacuum, ir, Gas, iquid, or any media that is compatible with the stainless steel piston rod and the steel stud. aximum pressure is 150 psi. The maximum hole size for each bore is shown in the chart below. The T piston bearing is not required because the two rod bushings provide excellent piston support. Hole Thru Stud Standard Standard lus iston odel No. odel No. Hole Size Suffix Hole Size Suffix ore thru stud (Std) thru stud (Std lus) /", 7/8" 1/16 -DR06 1-1/8" 1/8 -DR 5/ -DR16 1-5/8" 1/8 -DR 1/ -DR5 " 5/ -DR16 5/16 -DR1 7--01.10
Square 1 Cylinders Stroke Collar on piston rod Option How to Order 1/8" -C1 1) Start with the next 1/" -C longest stroke cylinder. ) Select the amount the /8" -C stroke is to be shortened. 1/" -C ) Use the corresponding 5/8" -C5 designation immediately after the stroke in the /" -C6 model number. 7/8" -C7 or those in-between strokes, a STROK COR of Delrin is incorporated on the piston rod. The collar fits tightly on the piston rod so that it cannot float as the piston is stroked. Tolerance on the stroke is ± 1/6". or tighter tolerances on the stroke or final rod position, contact engineering with application details. Stroke collar of Delrin Note: When using stroke collars in double rod units, C ND ROD STICK-OUT increases by amount stroke is shortened. djustable Retract Stroke Option -RS djusting Screw.17 ax. ny stroke with up to and including 1" adjustment. ny stroke with over 1" adjustment, specify the adjustment length after the -RS. xample: " djustment = -RS Thread sealing locknut /", 7/8", 1-1/8" ores = 1/ Hex 1-5/8" and " ores = 11/16 Hex Strokes 1" & Under = ax. + Stroke Strokes Over 1" = ax. + djustment n adjusting screw with a thread sealing locknut mounted in the Cap nd lug provides a simple, yet rugged and precision adjustment of the cylinder stroke in the retract direction. ores /", 7/8", and 1-1/8" have a 5/16"- thread giving 0.0" adjustment per revolution. ores 1-5/8" and " have a 1/-0 thread giving 0.050" adjustment per revolution. The -RS designation provides full stroke adjustment of any cylinder with 1" stroke or less, and 1" stroke adjustment on all longer strokes. When specifying longer adjustments on longer cylinders, add the desired adjustment to the -RS designation (1/" increments, please). xample: -RS will provide " of adjustment on any cylinder with " or more stroke. Sound imiters nd Only Cap nd Only oth & Cap nds Option - -R -R Sound limiting O'Ring Cushions Option -R shown or applications where you need a small amount of cushion at the end of the cylinder stroke to take out the metallic slap of piston head on piston stop. This is accomplished by placing an O'Ring on the rod at the piston, and/or in the cap end plug so that initial contact is with the elastomer and not metal-to-metal. The abco-ir design assures sufficient compression of the seals to allow full stroke. ecause of the temperature limitations of the adhesives involved, sound limiters are available in cylinders with internally lubricated una-n O'Rings only..11 7-17-01
Option Specifications Nonrotating Option -K 1-1/8", 1-5/8", and " bores only odel SQ 1 - - K shown n internal piston guide pin prohibits rod rotation so that objects attached to or moved by the rod will not rotate. Incorporating the guide mechanism inside the cylinder saves you the time, space and cost of mounting external guide pins and bushings in and around your mechanism. The guide pin and bushing are also protected from damage by the environment, the atmosphere, or mechanical abuse. These internal parts are lubricated by the system lubrication. vailable in 1-1/8", 1-5/8", and " bores. ay be used in conjunction with all options including - piston position sensing. Rotational accuracy is ±1. The warning label shown at the left is applied to each cylinder. WRNING THIS CINDR HS NONROTTING ROD. TO RVNT INTR DG HOD ROD WRNCH TS WHN INSTING OR ROVING TTCHNTS. Construction Details 1. The aluminum piston is attached to the piston rod with a socket flat head cap screw which is torqued for proper preload of the screw and clamping of the piston. octite on the threads and faces assures sealing and locks the assembly against pounding and vibration.. T bearing is standard in 1" strokes and longer for single rod models.. The non-rotating guide pin is ground tool steel for precision and long life. Incorporated inside the cylinder it is protected from environmental dirt and grime and mechanical abuse. It receives lubrication from the air system lubricator.. precision machined guide pin support block is attached to each end of the cylinder by a flat head screw. These support blocks provide rigid and precise location of the guide pin. 5. The guide pin passes through a polyurethane O-ring seal and an S660 bearing bronze bushing installed in the piston head. This combination provides "no-leak" precision guiding and long life. 6. disk of rubber is included at the end of the guide pin to take up end play and firmly seat the pin in its support blocks. 7--01.1
Square 1 Cylinders agnetic iston Option - Includes Dovetail ounting Slots Order Sensors Separately Dovetail style sensors are actuated by a magnetic piston. Sensor dovetail slides into a mating slot on the cylinder body, is positioned as desired, and locked in place with a slotted set screw. agnetic piston and 1/" Dovetail mounting slot(s) are specified with Suffix Option "" in the model number. onger stroke cylinders are furnished with a single mounting slot located at position # shown in the drawings at the # right. Shorter stroke cylinders are furnished with a second slot located at position # Order sensors separately. This short stroke odel SQ requires two dovetail mounting slots for proper positioning of sensors to detect beginning and end of stroke. This longer stroke odel SQ, side lug mounting style, has room enough to fit multiple sensors in a single slot. SQ rofile SQ rofile SQ rofile nd ort # Sensor stick-out: /" ore =.07" Other bores =.1".1" Ref. to 5 wire outlet Standard Stroke & Slot ocation Guide SQ (Side Tap) SQ (ace ount) SQ (Side ug) /" 1 1 /8" 1 5 /8" " /" 1 1 /8" 1 5 /8" " 7 /8" 1 1 /8" 1 5 /8" " Stroke 0 11 1 1 0 11 1 1 06 11 1 1 1/8 1/ 1/ / 1 1-1/,, 5, 6 Grey shaded area indicates that sensor mounting slots are provided with option -. Unshaded area indicates that a single sensor mounting slot is provided with option -. ow rofile, Solid State, agnetic iston osition Sensors Temperature Range: 0 to +80 C ( to +176 ) emale Cordsets for Quick Disconnect ength 1 eter eters 5 eters art No. CC-1 CC- CC-5 ncased in plastic housing, dovetail style sensors are corrosion resistant. 5 wire outlet allows close mounting. rofile shown here is typical. Dovetail Style agnetic Sensors for Square 1 Cylinders Cylinder odel ll Square 1's ll Square 1's. Sensor Type lectronic lectronic rewired 9 ft. art No. 99-000-01 99-000-0 Quick Disconnect art No.* 99-000-1 99-000- lectrical Characteristics Sourcing N 6- VDC, 0.0 mp ax current, 0.5 Voltage Drop Sinking NN 6- VDC, 0.0 mp ax current, 0.5 Voltage Drop Note*: Quick disconnect styles are supplied with 6 inch pigtail with male connector. Order female cordsets separately. D es es 7-17-01
Option Specifications xternal Guide, Nonrotating Option -G Square Ref. + Stroke Square Guide ins Hard Chrome lated Steel CC Superior nonrotating piston rod feature for applications such as package placement, figure stamping, and any application where anti-rotation and registration are critical as the piston is extended and retracted. mounting block is bolted to the piston rod. This block has two square pins mounted to it which in turn pass through guide blocks mounted on the sides of the cylinder. DD DD ounting lock Clear nodized luminum Guide lock Hard nodized luminum Clearance in Guide lock ounting Holes allow for adjustment to compensate for wear GG HH KK ounting Holes laces Square guide pins are hard chrome plated steel for long wear and corrosion resistance. Guide blocks are hard anodized aluminum for long wear and corrosion resistance. Clearance in guide block mounting holes provide for adjustment and backlash control, compensation for wear, and minimal rotation. xtended distance between guides provides superior nonrotation and support. xtended piston rod provides clearance between cylinder and guide bar mounting block to eliminate pinch points. ounting Series SQ or SQ odel 0 11 1 1 ore /" 1 1/8" 1 5/8" " 1.5 1.00 CC DD 1.9.6.5.87 1.06 1 1.00 GG HH.5.5.5 KK #6- #8-1/-0 5/16-18 lange Style 7 7-6-01 R 1 lange Style 8 & 9 R SQW-11-1 1 / with H7-11 T X Sq. G 1 1 T U T U 1 Dia. laces Dia. laces ore /" 1-1/8" 1-5/8" " " odel 0 11 1 1 1 Style 7 7 7 8 9 Series SQ Sq. X W 1 1 Series SQW Dia. laces ort ositions 1 Standard all models. To achieve, or, rotate flange. or 1, specify Option -1 or,, or : Specify Option -1 and rotate flange Kit # H7-0 H7-11 H7-1 H8-1 H9-1 1.5 1.00 1 1.00 lange ounting Kits for Series SQ and SQW lange ore abco ounting Hole attern Style Size Kit No. Interchange Information Hole attern C&C: 1-1/8" ore, Series T,, & R 7 /" H7-0 osier: 1-1/8" ore, Series TV, 8 & 9 HD: 1-1/8" ore, Series V, R, & C Hole attern Compact ir: /" ore, Style S,, & R Hole attern C&C: 1-1/8" ore, Series T,, & R 7 1-1/8" H7-11 osier: 1-1/8" ore, Series TV, 8 & 9 7 1-5/8" H7-1 HD: 1-1/8" ore, Series V, R, & C Hole attern Compact ir: 1-1/8" ore, Style S,, & R Hole attern N Code 1 & for 1-1/" ore ll brands conforming to this code Hole attern Compact ir:1-5/8" ore, Style S,, & R 8 " H8-1 Hole attern N Code 1 & for " ore ll brands conforming to this code 9 " H9-1 Hole attern Compact ir:" ore, Style S,, & R Kits include lange and lange ounting Screws.5.5.8..... G. R 1. 1.8.00 T.00 T 1.00 T.00.00 U. W 0 0 X.56.81.81.1
ating ye racket Trunnion ount Kit for Series SQ ounting Screws Included / Clearance Clevis / c c D Dia. Clevis racket ye racket aterials racket: High strength Zinc die casting ivot ins: recision dowel pins Clips:, lated steel ounting screws:, Steel, plated or black oxided ore /" 1-1/8" 1-5/8" " ore /" 1-1/8" 1-5/8" " " Kit No. TR-0 TR-11 TR-1 TR-1 Stroke ll ll ll 1/ 1/ Up 1.5 1.00 nd Clevis nglish RC-19 RC-1 RC-8 RC-5 RC-56.00.00 ounting Kits etric RC-19 RC-1 RC-8 RC-5 RC-56 C.5 D.15 ating ye kt. -0-0 -11-11 -11.5.. Clevis racket -0-11 -1-1 -1 SQW-11-1 with TR-11.81.9 Cap nd.07.06.06.06 ye racket -0-11 -1-1 -1 Clevis racket Kit for Series SQ N C K D H I art # -0-11 -1-1 1.5 1.00 0 1.5 1.5 aterials racket: High strength Zinc die casting ushings: Oil filled powdered metal in: 16 Stainless Steel Clips:, lated steel Screws:, Steel, plated or black oxided C 0 0 1.5 1.5 D 0.5 0 0 0 in 5.75.75 Hole.51 5.76.76 0.8 1.1 1.8 1.8 H.16.5 I 0.56 0.9 0.81 1. 1 1 K 0 1. 1.00.0.6.5.5.1 N 1/-0x 1/-0x 1/-0x 5/16-18x ye racket Kit for Series SQ N K aterials racket: High strength Zinc die casting ushings: Oil filled powdered metal Screws:, Steel, plated or black oxided K D H I art # -0-0 -11-1 -1 1.5 1.5 1.00 D.18..0.6.6.1885.51 5.76.76 H.16.16.5 I 0.56 0.56 0.9 1. 1. 0.87 0.87 1 1 1 *Note: Special 1/-0 with #1 hillips Head. K 0 0 1. 1.00..56.56.6.1.81.81 N 1/-0x HS* 1/-0x HS* 1/-0x HS* 1/-0x HS* 5/16-18x HSCS Clevises D aterials Clevis and Stud: Steel, black oxided in: 16 Stainless Steel Clips: Steel, plated I in C art # RC-19, RC-19 RC-1, RC-1 RC-8, RC-8 RC-5, RC-5 RC-56, RC-56 C 0 0 D.5... IN.1870.95 0 0 0 0.70 0.96 1.1 1.1 1.1 I 0 0 1.5 1 1 1.16 1 1 1..61.61.61 nglish 10-x.5 5/16-x 8-x.7 1/-0x 1/-0x.6 etric 5x6.mm 8x9.7mm 10x9.mm 1x9.9mm 1x15.7mm.15 7-17-01