EQUIPMENT = 20.10% IMPLEMENTS = 15% PARTS = 8.5% WHOLEGOODS PRICE LIST EFFECTIVE MARCH 17, 2014

Transcription

1 WHEEL LOADERS EQUIPMENT = 20.10% IMPLEMENTS = 15% PARTS = 8.5% WHOLEGOODS PRICE LIST EFFECTIVE MARCH 17, 2014 Please replace all pages of this section of the current price book. These pages are a complete revision of this section. All prices are effective as of March 17, Complete revision March 17, Page 12-1

2 R420ST3 R420ST3 Articulated Wheel Loader ENGINE D1503 Interim Tier 4 Kubota Diesel Engine 3 Cylinder, 4 Cycle 39.0 Net 2600 rpm FEATURES: Turbocharged 5 Second Pre Heat System Auto Air Bleed Fuel System E-TVCS - Low Emissions Design SAMPLE R420ST3 AS LOADER EQUIPPED WITH: K9716 Hydraulic Quick Coupler K9163A General Purpose Bucket 0.5 cu yd K9931-1,500 lbs Counter Weight DIMENSIONS: Operating Weight 7,450 lbs Overall Length (w/bucket & Weight) 165.8" Overall Height (W/ 2 - Post ROPS/FOPS) 98.8" Overall Width (w/o Bucket) 59.8" SAMPLE R420ST3 AS LOADER & BACKHOE EQUIPPED WITH: K9915 Mechanical Quick Coupler K9163A General Purpose Bucket 0.5 cu yd RBK4009S 9' Maximum Digging Depth Backhoe K7861A 18 inch Backhoe Bucket DIMENSIONS: Operating Weight 7,415 Ibs Overall Length (w/bucket & Backhoe) 187.8" Overall Height (w/o Bucket) 98.8" Overall Width (W/ 2 - Post ROPS/FOPS) 59.8" FEATURES One Speed Transmission Push Button Travel Speed Limiter Switch in Loader Lever "LST"- Load Sensing Transmission Articulated Steering, Frame Oscillation Quick Attaching System Front and Rear, Standard Weight Adjustable Suspension Seat, Standard Limited Slip Differential (Front), Standard BASIC UNITS R420ST3 with: K Post ROPS/FOPS Limited Slip Differential without: Quick Coupler Buckets Rear Counter Weight OPERATIONAL DIMENSIONS Bucket Capacity (SAE J742) 0.5 cu yd Tipping Load Straight w/bucket and 1,500 Ibs Counter Weight (SAE Rating) 4,585 lbs Tipping Load Straight w/pallet Forks and 1,500 Ibs Counter Weight (SAE Rating) 3,300 Ibs Hinge Pin Height 9' 2.7" Dump Height at Fully Raised Position 7' 4.4" Maximum Dump Angle 43º Reach Fully Raised at Maximum Dump Angle 30.8" Loader Bucket Breakout Force 6,550 lbs Steering Angle (each way) 40º Frame Oscillation Angle (Total) 8º Standard Tire Size (Bridgestone) 12.5/ ply Draw Bar Pull 5,500 Ibs Auxiliary Hydraulic Flow 11.1 GPM Complete revision March 17, Page 12-5

3 R420ST3 HOW TO SELECT A R420ST3 WHEEL LOADER (Sample Order Information Page) Below are samples of a complete R420ST3 Wheel Loader order. To submit your order, please select the Basic Unit Model you desire from Part 1 and the optional attachments needed to complete your order from parts 2 thru 7. STEP 1) Select from Part 1 the Basic Unit that fits your needs. For Example, Choose An R420S1T3 And Get: Base Model, 2-Post ROPS/FOPS Canopy, and Limited Slip Differential. STEP 2) Select from Part 2 thru 7 the optional attachments necessary to make the unit a complete machine. Add the Quick Coupler and Counterweight; choose a Loader Bucket, Pallet Forks or Backhoe and Buckets. SPECIAL NOTE: Quick Coupler must be ordered to connect all R420ST3 attachments. (SAMPLE S) SAMPLE UNIT R420S1T3, COMPLETE AND PRICE BASIC UNIT: R420S1T3 WHEEL LOADER WITH: 7275 $44, Post ROPS/FOPS Canopy Limited Slip Differential ATTACHMENTS: K9716 Hydraulic Quick Coupler 255 $2, K9163A General Purpose Bucket 415 $1, K9931 1,500 lbs. Counter Weight 1500 $1, $50, SAMPLE UNIT R420S1T3 WITH BACKHOE, COMPLETE AND PRICE BASIC UNIT: R420S1T3 WHEEL LOADER WITH: 7275 $44, Post ROPS/FOPS Canopy Limited Slip Differential ATTACHMENTS: K9715 Mechanical Quick Coupler 245 $1, K9163A General Purpose Bucket 415 $1, RBK4009S 9 ft. Digging Depth Backhoe 1605 $17, (Side Shift Type) K7861A 18" Backhoe Bucket. 159 $1, $66, Complete revision March 17, Page 12-6

4 R420ST3 PART 1 MODEL R420ST3 BASIC UNIT R420S1T3 WHEEL LOADER BASIC UNIT 7275 $44, Post ROPS/FOPS Canopy Limited Slip Differential R420S2T3 WHEEL LOADER BASIC UNIT 7825 $49, ROPS/FOPS Cab Limited Slip Differential PART 2 QUICK COUPLER SPECIAL NOTES: A quick coupler must be ordered to connect all R420ST3 attachments. The mounting pins and retaining plates included with the wheel loader are required to install the quick couplers. K9715 MECHANICAL QUICK COUPLER 245 $1, Skid Steer Loader Style. K9716 HYDRAULIC QUICK COUPLER 255 $2, Skid Steer Loader Style. Includes hydraulic fittings and hoses. PART 3 COUNTER K9931 1,500 Ibs. COUNTER 1500 $1, Quick Attach Counter Weight Retaining Pins, 2 pcs Eye Bolt Hitch Pin PART 4 LOADER BUCKETS K9163A GENERAL PURPOSE BUCKET 415 $1, inch 0.50 cu. yd. Quick Attach K9723 BOLT-ON CUTTING EDGE 75 $ for K9163A K9164 LIGHT MATERIAL BUCKET 541 $1, inch 0.75 cu. yd. Quick Attach S6625 SCRAP GRAPPLE BUCKET 955 $4, inch Quick Attach Requires a K7820 Hose Kit K7820 HOSE KIT for S $ Required for S6625 Installation S6632 BOLT-ON CUTTING EDGE 120 $ inch for S6625 PART 5 PALLET FORKS K Pallet Forks 500 $1, Complete with frame. Includes pallet fork rollback stop extensions Complete revision March 17, Page 12-7

5 R420ST3 PART 6 Attachments E9299 AM/FM Radio with MP3 Port and 7-Channel 4 $ Weather Band. Requires E9376 Mount Kit. E9276B AM/FM Radio CD/MP3 Player with 7-Channel 4 $ Weather Band. Requires E9376 Mount Kit. E9376 RADIO MOUNT KIT 5 $ Includes mount kit and antenna. PART 7 BACKHOE RBK4009S R420ST3 BACKHOE (SIDE SHIFT TYPE) 1605 $17, Without Bucket. Quick Attach. Seat Turntable Kit And Remote Throttle Included. Compatible With 2-Post Canopy Or Cab. Cab Installation Requires K4009 Kit. 9' 3" Maximum Digging Depth And 4,100 Lbs. Bucket Breakout Force Ibs Dipper Stick Breakout Force, 986 Ibs Boom Cylinder Lift Capacity, 1,015 Ibs Dipper Stick Lift Capacity, 180 Swing Angle. K4009 Backhoe Cab Conversion Kit 200 $1, BACKHOE BUCKETS FOR RBK4009S K7710A 12 inch 1.34 cu. ft. BUCKET 130 $ K7711A 16 inch 1.98 cu. ft. BUCKET 153 $ K7861A 18 inch 2.30 cu. ft. 3 HOLE, H.D. BUCKET 159 $1, K7713A 24 inch 3.29 cu. ft. BUCKET 192 $1, BUCKET PARTS INFORMATION FOR K7710A, K7711A, K7712A & K7713A PART NO Adaptor (230 x 156) (Standard) Tooth (X156) (Standard) Tooth Pin (P156) (Standard) PART 8 TIRES K9793L STANDARD TIRE Left 100 $ K9793R STANDARD TIRE Right 100 $ Bridgestone, 12.5/ ply with Rim. In base price of all R420ST3 Models. Radios have a 2-year warranty. Complete revision March 17, Page 12-8

6 R420ST3 PART 9 ROPS / FOPS K9940 Replacement 2-POST ROPS/FOPS Canopy 242 $1, For both Loader and Backhoe. K9945 Replacement ROPS / FOPS Cab 704 $5, For both Loader and Backhoe. With Heater. Filtered and Pressurized. PART 10 OPTIONAL PARTS PART NO. R Air filter pre-cleaner kit for operation in extremely dusty conditions R Loader bucket auto-leveler kit Block heater Complete revision March 17, Page 12-9

7 This page intentionally left blank. Complete revision March 17, Page 12-10

8 R520ST3 R520ST3 Articulated Wheel Loader ENGINE V2203 Kubota Interim Tier 4 Diesel Engine 4 Cylinder, 4 Cycle 43.8 Net 2600 rpm FEATURES: 5 Second Pre Heat System Auto Air Bleed Fuel System E-TVCS - Low Emissions Design FEATURES One Speed Transmission Push Button Travel Speed Limiter Switch in Loader Lever "LST"- Load Sensing Transmission. Articulated Steering, Frame Oscillation. Quick Attaching System Front and Rear, Standard Weight Adjustable Suspension Seat, Standard Limited Slip Differential (Front), Standard SAMPLE R520ST3 AS LOADER EQUIPPED WITH: K9726 Hydraulic Quick Coupler K9263A General Purpose Bucket 0.75 cu. yd. K9932-2,020 lbs Counter Weight DIMENSIONS: Operating Weight 8,980 lbs Overall Length (w/bucket & Weight) 184.5" Overall Height (W/ 2 - Post ROPS/FOPS) 101.6" Overall Width (w/o Bucket) 69.3" SAMPLE R520ST3 AS LOADER & BACKHOE EQUIPPED WITH: K9725 Mechanical Quick Coupler K9263A General Purpose Bucket 0.75 cu yd RBK5009S 9' Maximum Digging Depth Backhoe K7861A 18 inch Backhoe Bucket DIMENSIONS: Operating Weight 8,450 Ibs Overall Length (w/bucket & Backhoe) 206.5" Overall Height (w/o Bucket) 101.6" Overall Width (W/ 2 - Post ROPS/FOPS) 69.3" BASIC UNITS R520ST3 with: K Post ROPS/FOPS Limited Slip Differential without: Quick Coupler Buckets Rear Counter Weight OPERATIONAL DIMENSIONS Bucket Capacity (SAE J742) 0.75 cu yd Tipping Load Straight w/bucket and 2,020 Ibs Counter Weight (SAE Rating) 5,190 lbs Tipping Load Straight w/pallet Forks and 2,020 Ibs Counter Weight (SAE Rating) 3,870 Ibs Hinge Pin Height 10' 10" Dump Height at Fully Raised Position 8' 9.2" Maximum Dump Angle 41º Reach Fully Raised at Maximum Dump Angle 33.9" Loader Bucket Breakout Force 7,425 lbs Steering Angle (each way) 40º Frame Oscillation Angle (Total) 8º Standard Tire Size (Bridgestone) 15.5/ ply Draw Bar Pull 6,170 Ibs Auxiliary Hydraulic Flow 15.4 GPM Complete revision March 17, Page 12-11

9 R520ST3 HOW TO SELECT A R520ST3 WHEEL LOADER (Sample Order Information Page) Below are samples of a complete R520ST3 Wheel Loader order. To submit your order, please select the Basic Unit Model you desire from Part 1 and the optional attachments needed to complete your order from parts 2 thru 7. STEP 1) Select from Part 1 the Basic Unit that fits your needs. For Example, choose an R520S1T3 and get: Base Model, 2-Post ROPS/FOPS Canopy, and Limited Slip Differential. STEP 2) Select from Part 2 thru 7 the optional attachments necessary to make the unit a complete machine. Add the Quick Coupler and Counterweight; choose a Loader Bucket, Pallet Forks or Backhoe and Buckets. SPECIAL NOTE: Quick Coupler must be ordered to connect all R520ST3 attachments. (SAMPLE S) SAMPLE UNIT R520S1T3, COMPLETE AND PRICE BASIC UNIT: R520S2T3 WHEEL LOADER WITH: 9335 $57, ROPS/FOPS Cab Limited Slip Differential ATTACHMENTS: K9726 Hydraulic Quick Coupler 255 $2, K9263A General Purpose Bucket 610 $2, K9932 2,250 lbs. Counter Weight 2250 $2, $64, SAMPLE UNIT R520S1T3 WITH BACKHOE, COMPLETE AND PRICE BASIC UNIT: R520S1T3 WHEEL LOADER WITH: 9335 $52, Post ROPS/FOPS Canopy Limited Slip Differential ATTACHMENTS: K9725 Mechanical Quick Coupler 245 $1, K9263A General Purpose Bucket 610 $2, RBK5009S 9 ft. Digging Depth Backhoe 1625 $17, (Side Shift Type) K7861A 18" Backhoe Bucket. 159 $1, $74, Complete revision March 17, Page 12-12

10 R520ST3 PART 1 MODEL R520ST3 BASIC UNIT R520S1T3 WHEEL LOADER BASIC UNIT 9335 $52, Post ROPS/FOPS Canopy Limited Slip Differential R520S2T3 WHEEL LOADER BASIC UNIT 9885 $57, ROPS/FOPS Cab Limited Slip Differential PART 2 QUICK COUPLER SPECIAL NOTES: A Quick Coupler must be ordered to connect all R520ST3 attachments. The mounting pins and retaining plates included with the wheel loader are required to install the quick couplers. K9725 MECHANICAL QUICK COUPLER 245 $1, Skid Steer Loader Style. K9726 HYDRAULIC QUICK COUPLER 255 $2, Skid Steer Loader Style. Includes hydraulic fittings and hoses. PART 3 COUNTER K9932 2,250 lbs. Counter Weight 2250 $2, Quick Attach Counter Weight Retaining Pins, 2 pcs Eye Bolt Hitch Pin PART 4 LOADER BUCKETS K9263A GENERAL PURPOSE BUCKET 610 $2, inch 0.75 cu. yd. Quick Attach K9724 BOLT-ON CUTTING EDGE 98 $ for K9263A K9264 LIGHT MATERIAL BUCKET 605 $2, inch 1.0 cu. yd. Quick Attach S6625 SCRAP GRAPPLE BUCKET 955 $4, inch Quick Attach Requires a K7820 Hose Kit K7820 HOSE KIT for S $ Required for S6625 Installation S6632 BOLT-ON CUTTING EDGE 120 $ inch for S6625 LOADER BUCKET PARTS INFORMATION PART NO Optional Bolt-On Cutting Edge for K9264 PART 5 PALLET FORKS K Pallet Forks 500 $1, Complete with frame. Includes pallet fork rollback stop extensions Complete revision March 17, Page 12-13

11 R520ST3 PART 6 ATTACHMENTS E9299 RADIO OPTION, AM/FM Radio with MP3 Port 4 $ and 7-Channel Weather Band for Cab models only. Requires E9376 Mount Kit. E9276B RADIO OPTION, AM/FM Radio CD/MP3 Player 4 $ with 7-Channel Weather Band for Cab models only. Requires E9376 Mount Kit. E9376 Radio Mount Kit 5 $ Includes mount kit and antenna. PART 7 BACKHOE RBK5009S R520ST3 BACKHOE (SIDE SHIFT TYPE) 1625 $17, Without Bucket. Quick Attach. Seat Turntable Kit and Remote Throttle included. Compatible with 2-Post Canopy or Cab. Cab installation requires K4009 Kit. 9' 3" Maximum Digging Depth and 4,100 Lbs. Bucket Breakout Force Ibs. Dipper Stick Breakout Force, 986 Ibs Boom Cylinder Lift Capacity, 1,015 Ibs Dipper Stick Lift Capacity, 180 Swing Angle. K4009 Backhoe Cab Conversion Kit 200 $1, BACKHOE BUCKETS FOR RBK5009S K7710A 12 inch 1.34 cu. ft. BUCKET 130 $ K7711A 16 inch 1.98 cu. ft. BUCKET 153 $ K7861A 18 inch 2.30 cu. ft. 3 HOLE, H.D. BUCKET 159 $1, K7713A 24 inch 3.29 cu. ft. BUCKET 192 $1, BUCKET PARTS INFORMATION FOR K7710A, K7711A, K7712A & K7713A PART NO Adaptor (230 x 156) (Standard) Tooth (X156) (Standard) Tooth Pin (P156) (Standard) PART 8 TIRES K9794L STANDARD TIRE Left 145 $ K9794R STANDARD TIRE Right 145 $ Bridgestone, 15.5/ ply with Rim. In base price of all R520ST3 Models. PART 9 ROPS / FOPS K9940 Replacement 2-POST ROPS/FOPS Canopy 242 $1, For both Loader and Backhoe. K9945 Replacement ROPS / FOPS Cab 704 $5, For Both Loader and Backhoe. With Heater. Filtered and Pressurized. Radios have a 2-year warranty. Complete revision March 17, Page 12-14

12 R520ST3 PART 10 OPTIONAL PARTS PART NO. R Air filter pre-cleaner kit for operation in extremely dusty conditions R Loader bucket auto-leveler kit Block heater Complete revision March 17, Page 12-15

13 R-Series Replacement Engines REPLACEMENT ENGINES FOR R - SERIES WHEEL LOADERS V1305E2RP REPLACEMENT ENGINE FOR R $4, D1503T1RP1 REPLACEMENT ENGINE FOR R $5, V2203E2RP REPLACEMENT ENGINE FOR R $4, V2203E2BDW REPLACEMENT ENGINE FOR R $5, TIER 2 S/N & UP D1503MT2R1 REPLACEMENT ENGINE FOR R420S 440 $4, V2203M2RP REPLACEMENT ENGINE FOR R520S 512 $5, INTERIM TIER 4 D1503E3WL1 REPLACEMENT ENGINE FOR R420S 441 $5, V2203E3WL1 REPLACEMENT ENGINE FOR R520S 512 $5, Complete revision March 17, Page 12-17

14 COMPACT TRACK LOADERS WHOLEGOODS PRICE LIST EFFECTIVE MARCH 17, 2014 Please replace all pages of this section of the current price book. These pages are a complete revision of this section. All prices are effective as of March 17, Complete revision March 17, Page 14-1

15 SVL75-2 SVL75-2 Compact Track Loader FEATURES BASIC UNITS Vertical Lift Path Loader Frame SVL75-2, 12.6 Rubber Tracks, Open ROPS/FOPS Cab Standard Front Quick Coupler, Float Standard Mechanical Quick Coupler Hydraulic Quick Coupler Option SVL75-2H, 12.6 Rubber Tracks, Open ROPS/FOPS Cab Loader Arm Self-Leveling Hydraulic Quick Coupler Loader Boom Lock SVL75-2W, 15.0 Rubber Tracks, Open ROPS/FOPS Cab Open ROPS & Air Conditioned ROPS/FOPS Cab Models Mechanical Quick Coupler High Back, Adjustable, Vinyl, Suspension Seat SVL75-2HW, 15.0 Rubber Tracks, Open ROPS/FOPS Cab 2" Retractable Seat Belt and 2-Piece Seat Bar Hydraulic Quick Coupler 12V Electric Outlet SVL75-2C, 12.6 Rubber Tracks, A/C ROPS/FOPS Cab 18.8 Gpm Auxiliary Hydraulics Mechanical Quick Coupler Direct To Tank Return Line SVL75-2HC, 12.6 Rubber Tracks, A/C ROPS/FOPS Cab Rigid Mounted Undercarriage, 4 Lower Track Rollers Hydraulic Quick Coupler Rubber Tracks, 12.6 Standard, 15 Optional SVL75-2WC, 15.0 Rubber Tracks, A/C ROPS/FOPS Cab Two Speed Travel System Mechanical Quick Coupler Automatic Wet Disk Parking Brake SVL75-2HWC, 15.0 Rubber Tracks, A/C ROPS/FOPS Cab Kubota 4 Hydraulic Pump Load Sensing System Hydraulic Quick Coupler 2 Gear, 2 Variable Displacement Pumps Hydraulic Joystick Controls ENGINE ISO Operating Pattern V3307 Kubota CR-TE4, Interim Tier 4 Diesel Engine Hand And Foot Throttle Controls 4 Cylinder, 4 Cycle, Turbo Charged Electronic Travel Torque Management 74.3 Gross 2400 rpm Automatic Glow Plugs Key Switch Stop/Start System DIMENSIONS Self Bleed Fuel System Cab Height Front and 2 Rear Working Lights Width (without attachment) Hour Meter, Engine Temperature and Fuel Width with wide track option (without Gauges and Warning Lights attachment) Horn and Backup Alarm Length (without attachment) Lockable Fuel Cap Bolt On Grab Handles to enter machine Length of Track on Ground OPERATIONAL DIMENSIONS Operating Weight*, SVL75H, 12.6 Rubber Tracks, Open ROPS/FOPS Cab, Mechanical Quick Coupler... 9,040 lbs. Rated Operating Capacity (@ 35% of Tipping Load)... 2,300 lbs. Rated Operating Capacity 35% of Tipping Load complies with ISO and SAE J 818 for crawler loaders Rated Operating Capacity 50% of Tipping Load... 3,285 lbs. Tipping Load... 6,570 lbs. Auxiliary Hydraulics Flow gpm Travel Speed (Low / High) / 5.1 mph Maximum Height Height to Hinge Pin Ground Pressure psi. Traction Force... 9,678 lbf. * Includes operator s weight, 175 lbs. Complete revision March 17, Page 14-11

16 SVL75-2 HOW TO SELECT AN SVL75-2 Compact Track Loader (Sample Order Information Page) Below are examples of a complete SVL75 order. To submit your order, please select the Basic Unit Model that you desire from Part 1. Then select the attachments from Parts 2 and 3 needed to complete your order. STEP 1) STEP 2) Select from Part 1 the Basic Unit that fits your needs. For example, choose a SVL75-2 and get: Base Model, rubber tracks, open ROPS/FOPS cab, and a mechanical quick coupler. Select from Parts 2 and 3 the attachments necessary to make the unit a complete machine. Choose buckets and bolt-on edges, accessories, or a hydraulic breaker. Parts items are available in Part 4. (SAMPLE ) STANDARD UNIT SVL75-2 COMPLETE AND PRICE BASIC UNIT: SVL75-2 COMPACT TRACK LOADER BASIC UNIT 8864 $54, Rubber Tracks Open ROPS/FOPS Cab Mechanical Quick Coupler ATTACHMENTS: S " low profile standard floor bucket with 500 $1, teeth and bolt-on side cutters S Pallet Forks 385 $1, $56, STANDARD UNIT SVL75H-2WC COMPLETE AND PRICE BASIC UNIT: SVL75-2HWC COMPACT TRACK LOADER BASIC UNIT 9272 $62, Wide Rubber Tracks A/C ROPS/FOPS Cab Hydraulic Quick Coupler ATTACHMENTS: S " 4 in 1 Bucket 910 $4, S6632 Bolt-On-Cutting Edge 120 $ S Pallet Forks 385 $1, $68, Complete revision March 17, Page 14-12

17 SVL75-2 PART 1 MODEL SVL75-2 BASIC UNITS SVL75-2 COMPACT TRACK LOADER BASIC UNIT 8864 $54, Rubber Tracks, Open ROPS/FOPS Cab Mechanical Quick Coupler SVL75-2H COMPACT TRACK LOADER BASIC UNIT 8908 $55, Rubber Tracks, Open ROPS/FOPS Cab Hydraulic Quick Coupler SVL75-2W COMPACT TRACK LOADER BASIC UNIT 8952 $55, Rubber Tracks, Open ROPS/FOPS Cab Mechanical Quick Coupler SVL75-2HW COMPACT TRACK LOADER BASIC UNIT 8996 $57, Rubber Tracks, Open ROPS/FOPS Cab Hydraulic Quick Coupler SVL75-2C COMPACT TRACK LOADER BASIC UNIT 9140 $59, Rubber Tracks, A/C ROPS/FOPS Cab Mechanical Quick Coupler SVL75-2HC COMPACT TRACK LOADER BASIC UNIT 9184 $61, Rubber Tracks, A/C ROPS/FOPS Cab Hydraulic Quick Coupler SVL75-2WC COMPACT TRACK LOADER BASIC UNIT 9228 $61, Rubber Tracks, A/C ROPS/FOPS Cab Mechanical Quick Coupler SVL75-2HWC COMPACT TRACK LOADER BASIC UNIT 9272 $62, Rubber Tracks, A/C ROPS/FOPS Cab Hydraulic Quick Coupler PART 2 BUCKETS QUICK ATTACH BUCKETS S Low Profile, Standard Floor, Teeth, Side 500 $1, Cutter, 14.3 cu-ft heaped capacity S Low Profile, Standard Floor, Cutting Edge, 450 $1, Side Cutter, 14.3 cu-ft heaped capacity S Low Profile, Long Floor, Teeth, Side Cutter 565 $1, cu-ft heaped capacity S Low Profile, Long Floor, Cutting Edge, Side 515 $1, Cutter, 17.8 cu-ft heaped capacity S Low Profile, Standard Floor, Teeth, Side 530 $1, Cutter, 15.2 cu-ft heaped capacity Complete revision March 17, Page 14-13

18 SVL75-2 ATTACHMENTS PART 2 BUCKETS (Continued) S Low Profile, Standard Floor, Cutting Edge, 473 $1, Side Cutter, 15.2 cu-ft heaped capacity S Low Profile, Long Floor, Teeth, Side Cutter 590 $1, cu-ft heaped capacity S Low Profile, Long Floor, Cutting Edge, Side 533 $1, Cutter, 18.9 cu-ft heaped capacity S in 1 Bucket, no BOE nor Side Cutter 910 $4, Recommend use of S6689 Hose Stay S Utility Scrap Grapple, Bolt-on Edge optional 955 $4, Recommend use of S6689 Hose Stay S6631 Bolt-On Cutting Edge for 68 Bucket 112 $ Includes Mounting Hardware S6632 Bolt-On Cutting Edge for 72 Bucket 120 $ Includes Mounting Hardware S6634 Side Cutter for All 68, 72 Buckets, Set of 2 18 $65.00 Includes Mounting Hardware S Spill Guard 4-N-1 Bucket 30 $ PART 3 ATTACHMENTS S Pallet Forks Complete with Frame 385 $1, S6691 Roof Mounted Water Tank 65 $1, Includes Mounting Hardware, Frame, Tank, 12V Pump and Wiring Harness KXB560Q HYDRAULIC BREAKER 820 $11, Includes manual, side plates, one moil point and one chisel point. Requires a S6693 hose kit, S6692 mount bracket, and Special Application Door S6693 HYDRAULIC BREAKER HOSE KIT 7 $ S6692 HYDRAULIC BREAKER BRACKET 175 $1, Required for KXB560Q Hydraulic Breakers S6698 SPECIAL APPLICATION DOOR FOR ROPS MODELS 135 $3, With frame and wiper, to be used with ROPS models only with swing style door. Made from polycarbonate. Required when using a hydraulic breaker and recommended when using a rotary cutter or mowers and mulchers Can still be used in combination with S6682, S6683, S8884, S6685, and S6687 S6658 SPECIAL APPLICATION DOOR FOR CAB MODELS 135 $2, With frame and wiper, to be used with Enclosed Cab models only with tilt-up style door. Made from polycarbonate. Required when using a hydraulic breaker and recommended when using a rotary cutter or mowers and mulchers. Complete revision March 17, Page 14-14

19 SVL75-2 ATTACHMENTS PART 3 ATTACHMENTS (Continued) K7773 ACCUMULATOR CHARGE KIT 5 $ Required for hydraulic breaker maintenance only, one kit for servicing all breakers. S6627 Replacement Open ROPS Cab/SVL75-2 $7, S6628 Replacement Closed ROPS Cab/SVL75-2 Cab $11, SEE REPLACEMENT CAB & ROPS ADOPTION LIST PART 4 REPLACEMENT CAB/ROPS FOR SVL75-2 Complete package that is direct-fit to the main frame mounting points. Hydraulic hoses ready to fit into main manifold. Includes standard suspension seat and new "bolt-on" style grab handles. Lift-Assist gas struts are not included. ACCESSORIES K9926 RETRACTABLE SEAT BELT OPTION (3 WIDE) 3 $80.00 As required in some states for OSHA compliance. S6679 Air Ride Seat Suspension Kit 55 $ S6677 Red Tail Light Kit 3 $ S6676 Strobe Light Kit 3 $ S6678 Rotating Beacon Light Kit 3 $ S6641 Rearview Mirror includes Mounting Bracket & Hardware $21.00 S6675 Spark Arrestor Muffler (not required on SVL75-2) 50 $ Requires S6688 heat insulation kit. S6688 Heat Insulation Kit 2.5 $ Required for S6675 installations S6689 Hose Stay (Group attachment hoses together at 3 $70.00 Loader frame base) Recommend for use with: Brush Grapple, Scrap Grapple, Hopper Sweeper, 4-in-1 bucket, and Tilt Attach ENCLOSURE KITS (for ROPS Models Only) S6681A Door Kit (Swing) with Frame and Wiper 170 $1, and Quick Glass Release Handles S6682 Sliding Side Window Kit 170 $ S6683A Heater Kit 16 $ S6684 Windshield Washer Kit 5 $ S6685 Circulation Fan Kit 25 $ S6687 Mounting Bracket for Magnetic Base 3 $60.00 PART 5 Available from Parts V Pin Attachment Coupler Kit V Engine Bonnet Lock Kit V Radiator Screen Kit Engine Block Heater Radio Kit Complete revision March 17, Page 14-15

20 SVL75-2 ATTACHMENTS REPLACEMENT CAB & ROPS ADOPTION LIST SVL75-2 SVL75-2 REPLACEMENT CAB & ROPS ADOPTION LIST Cab/ROPS # Model Cab or ROPS WG# 1 SVL75-2C Cab S SVL75-2CH Cab see Chart 1 3 SVL75-2 ROPS S SVL75-2H ROPS see Chart 2 Chart 1 For Cab NO.2, order additional parts below; S6628 Part # SVL75-2CH QTY V Cover 1 V Switch 1 And need to remove below part from the Cab RD Cap 1 Chart 2 For ROPS NO.4, order additional parts below ; S6627 Part # SVL75-2H QTY V Cover 1 V Switch 1 And need to remove below part from the ROPS R D Cap 1 Complete revision March 17, Page 14-16

21 SVL75-2 ATTACHMENTS PART 6 APPROVED ALLIED ATTACHMENTS MANUFACTURER S NUMBER Trencher Std Flow, Model 625 w/36 Boom, 6 cup type Teeth, TES chain Trencher Std Flow, model 625 with 48 boom, 6 cup type Teeth, TES chain Dozer Blade Tilt Attach (Recommend use of S6689 Hose Stay) Rotary Cutter (Std Flow) Gauge Wheels are optional MX7H Power Rake MX7H Std. Flow E Tiller (Std Flow) mechanical Offset, 6 tines, optional: Tooth Scarifier p/n: Utility Brush Grapple (Recommend use of S6689 Hose Stay) Construction Brush Grapple (recommended for SVL90) 11007E Snow Blower (Std Flow) (recommended for SVL75) LAF Snow Blade 20584M Hopper Sweeper (opt: nozzle kit & Gutter Brush) (Recommend use of S6689 Hose Stay) VRS7M VRS Pick-up Sweepster (opt: nozzle kit & Gutter Brush) 22084M QC Angle Broom Std Flow (order angle kit separately) QCSS Hydraulic Angle Kit with LAF9360 for use on 20084M-0174)) Tree Spade 36" - Series Vibratory Roller - model: PD-VRP Rock Saw - RS24 (ONLY for SVL90-2 Hi-Flow) Root Rake w/grapple Skid Swing Hoe Tree Forks Post Driver - model: PD4800 LAF Tree Scoop 48" Concrete Claw LAF Soil Preparator Side Discharge Bucket 72" High Volume Heavy Duty Snow Bucket - 108" LAF Auto Rake - 84" Auger Drive - X HEX Drive, incl. mounting frame Rated at gpm CONTACT: Bradco 503 Gay Street Delhi, IA (800) Fax (319) Harley 503 Gay Street Delhi, IA (800) Fax (319) FFC 503 Gay Street Delhi, IA (800) Fax (319) Sweepster 503 Gay Street Delhi, IA (800) Fax (319) Paladin/Bradco 503 Gay Street Delhi, IA (800) Fax (319) Paladin/FFC 503 Gay Street Delhi, IA (800) Fax (319) McMillen 503 Gay Street Delhi, IA (800) Fax (319) For Auger Bit selection, please consult the Paladin catalog, as there is a wide variety of sizes, shapes and applications. Complete revision March 17, Page 14-17

22 SVL90-2 SVL90-2 Compact Track Loader FEATURES BASIC UNITS Interim Tier 4 Certified Kubota Diesel Engine SVL90-2, 17.7 Rubber Tracks, Open ROPS/FOPS Cab Electronic Travel Torque Management System Mechanical Quick Coupler Vertical Lift Path Loader Frame SVL90-2H, 17.7 Rubber Tracks, Open ROPS/FOPS Cab Standard Front Quick Coupler, Float Standard Hydraulic Quick Coupler Hydraulic Quick Coupler Option SVL90-2F, 17.7 Rubber Tracks, Open ROPS/FOPS Cab Loader Arm Self-Leveling Mechanical Quick Coupler, High Flow Auxiliary Hydraulics Loader Boom Lock SVL90-2HF, 17.7 Rubber Tracks, Open ROPS/FOPS Cab Open ROPS/FOPS Hydraulic Quick Coupler, High Flow Auxiliary Hydraulics Optional enclosed and pressurized cab with A/C SVL90-2C, 17.7 Rubber Tracks, A/C ROPS/FOPS Cab High Back, Adjustable, Vinyl, Suspension Seat Mechanical Quick Coupler 2" Retractable Seat Belt And 2-Piece Seat Bar SVL90-2HC, 17.7 Rubber Tracks, A/C ROPS/FOPS Cab 12V Electric Outlet Hydraulic Quick Coupler 25.1 gpm Auxiliary Hydraulics Standard, 36.5 gpm Option SVL90-2FC, 17.7 Rubber Tracks, A/C ROPS/FOPS Cab Direct To Tank Return Line Mechanical Quick Coupler, High Flow Auxiliary Hydraulics Rigid Mounted Undercarriage, 5 Lower Track Rollers SVL90-2HFC, 17.7 Rubber Tracks, A/C ROPS/FOPS Cab Rubber Tracks, 17.7 Standard Hydraulic Quick Coupler, High Flow Auxiliary Hydraulics Two Speed Travel System Automatic Wet Disk Parking Brake Kubota 4 Hydraulic Pump Load Sensing System 1 Gear and 2 Variable Displacement Pumps, 1 additional Gear pump for high flow Option ENGINE Hydraulic Joystick Controls V3800-CR-TE4 Kubota Interim Tier 4 Diesel Engine ISO Operating Pattern 4 Cylinder, 4 Cycle, Turbo Charged Hand And Foot Throttle Controls 92.0 Gross 2400 rpm Stall Guard Engine Control Automatic Glow Plugs DIMENSIONS Key Switch Stop System Cab Height 83.4 Self Bleed Fuel System Width (without attachment) Front And 2 Rear Working Lights Length (without attachment) Hour Meter, Engine Temperature And Fuel Length of Track on Ground 65.6 Gauges And Warning Lights Horn And Backup Alarm Lockable Fuel Cap OPERATIONAL DIMENSIONS Operating Weight*, SVL90-2H, 17.7 Rubber Tracks, Open ROPS/FOPS Cab, Mechanical Quick Coupler 10,915 lbs. Rated Operating Capacity 35% of Tipping Load complies with ISO and SAE J 818) 3,010 lbs. Rated Operating Capacity 50% of Tipping Load 4,300 lbs. Tipping Load 8,600 lbs. Auxiliary Hydraulics Flow 25.1 / 36.5 gpm Travel Speed (Low / High) 5.0 / 7.3 mph Maximum Height 40.7 Height to Hinge Pin Ground Pressure 4.2 psi. Traction Force 12,178 lbf. * Includes operator s weight, 175 lbs. Complete revision March 17, Page 14-18

23 SVL90-2 HOW TO SELECT AN SVL90-2 Compact Track Loader (Sample Order Information Page) Below are examples of a complete SVL90 order. To submit your order, please select the Basic Unit Model that you desire from Part 1. Then select the attachments from Parts 2 and 3 needed to complete your order. STEP 1) STEP 2) Select from Part 1 the Basic Unit that fits your needs. For example, choose a SVL90-2 and get: Base Model, rubber tracks, open ROPS/FOPS cab, and a mechanical quick coupler. Select from Parts 2 and 3 the attachments necessary to make the unit a complete machine. Choose buckets and bolt-on edges, accessories, or a hydraulic breaker. Parts items are available in Part 4. (SAMPLE ) STANDARD UNIT SVL90-2 COMPLETE AND PRICE BASIC UNIT: SVL90-2 COMPACT TRACK LOADER BASIC UNIT $63, Rubber Tracks Open ROPS/FOPS Cab Mechanical Quick Coupler ATTACHMENTS: S " low profile standard floor bucket with 625 $1, teeth and bolt-on side cutters S Pallet Forks 385 $1, $66, STANDARD UNIT SVL90-2HC COMPLETE AND PRICE BASIC UNIT: SVL90-2HC COMPACT TRACK LOADER BASIC UNIT $70, Rubber Tracks A/C ROPS/FOPS Cab Hydraulic Quick Coupler ATTACHMENTS: S " 4 in 1 Bucket 965 $4, S Bolt-On-Cutting Edge 132 $ S6679 Air Ride Seat Suspension Kit 55 $ $75, Complete revision March 17, Page 14-19

24 SVL90-2 PART 1 MODEL SVL90-2 BASIC UNITS SVL90-2 COMPACT TRACK LOADER BASIC UNIT $63, Rubber Tracks, Open ROPS/FOPS Cab Mechanical Quick Coupler SVL90-2H COMPACT TRACK LOADER BASIC UNIT $65, Rubber Tracks, Open ROPS/FOPS Cab Hydraulic Quick Coupler SVL90-2F COMPACT TRACK LOADER BASIC UNIT $66, Rubber Tracks, Open ROPS/FOPS Cab Mechanical Quick Coupler, High Flow Auxiliary Hydraulics SVL90-2HF COMPACT TRACK LOADER BASIC UNIT $67, Rubber Tracks, Open ROPS/FOPS Cab Hydraulic Quick Coupler, High Flow Auxiliary Hydraulics SVL90-2C COMPACT TRACK LOADER BASIC UNIT $68, Rubber Tracks, A/C ROPS/FOPS Cab Mechanical Quick Coupler SVL90-2HC COMPACT TRACK LOADER BASIC UNIT $70, Rubber Tracks, A/C ROPS/FOPS Cab Hydraulic Quick Coupler SVL90-2FC COMPACT TRACK LOADER BASIC UNIT $71, Rubber Tracks, A/C ROPS/FOPS Cab Mechanical Quick Coupler, High Flow Auxiliary Hydraulics SVL90-2HFC COMPACT TRACK LOADER BASIC UNIT $72, Rubber Tracks, A/C ROPS/FOPS Cab Hydraulic Quick Coupler, High Flow Auxiliary Hydraulics PART 2 BUCKETS -- QUICK ATTACH S Low Profile, Standard Floor, Teeth, Side Cutter 625 $1, cu-ft heaped capacity S Low Profile, Standard Floor, Cutting Edge, Side 560 $1, Cutter, 16.8 cu-ft heaped capacity S Low Profile, Long Floor, Teeth, Side Cutter 690 $1, cu-ft heaped capacity S Low Profile, Long Floor, Cutting Edge, Side Cutter 625 $1, cu-ft heaped capacity S High Capacity, Teeth, Side Cutter 831 $1, cu-ft heaped capacity S High Capacity, Side Cutter and BOCE 720 $1, cu-ft heaped capacity S in-1 Bucket, no BOE nor Side Cutter 965 $4, Recommend use of S6689 Hose Stay S Construction Scrap Grapple, Bolt-on Edge Optional 1211 $4, Recommend use of S6689 Hose Stay S " Bolt-On Cutting Edge for 80 Bucket 132 $ Includes Mounting Hardware S6634 Side Cutter for SVL75 & SVL90-2 Buckets, Set of 2 18 $65.00 S " Bolt-on Cutting Edge for Scrap Grapple 125 $ S Spill Guard for S N-1 bucket 34 $ Complete revision March 17, Page 14-20

25 SVL90-2 ATTACHMENTS PART 3 ATTACHMENTS S Pallet Forks, Complete with Frame 385 $1, S6691 Roof Mounted Water Tank 65 $1, Includes Mounting Hardware, Frame, 30 gal. Tank, 12V Pump and Wiring Harness KXB560Q HYDRAULIC BREAKER 820 $11, Includes manual, side plates, one moil point and one chisel point. Requires S6693 Hose Kit, S6692 Mount Bracket and Special Application Door S6693 HYDRAULIC BREAKER HOSE KIT 7 $ S6692 HYDRAULIC BREAKER BRACKET 175 $1, Required for KXB560Q Hydraulic Breakers S6698 SPECIAL APPLICATION DOOR FOR ROPS MODELS 135 $3, With frame and wiper, to be used with ROPS models only with swing-style door. Made from polycarbonate. Required when using a hydraulic breaker and recommended when using a rotary cutter or mowers and mulchers Can still be used in combination with S6682, S6683, S8884, S6685, and S6687 S6658 SPECIAL APPLICATION DOOR FOR CAB MODELS 135 $2, With frame and wiper, to be used with Enclosed Cab models only with tilt-up style door. Made from polycarbonate. Required when using a hydraulic breaker and recommended when using a rotary cutter or mowers and mulchers. K7773 ACCUMULATOR CHARGE KIT 5 $ Required for hydraulic breaker maintenance only, one kit for servicing all breakers. REPLACEMENT CAB/ROPS Complete package that is direct-fit to the main frame mounting points. Hydraulic hoses ready to fit into main manifold. Includes standard suspension seat and new "bolt-on" style grab handles. Lift-Assist gas struts are not included. S6629 REPLACEMENT OPEN ROPS CAB/SVL $7, S6630 REPLACEMENT CLOSED ROPS CAB/SVL90-2 CAB 704 $11, SEE REPLACEMENT CAB & ROPS ADOPTION LIST Complete revision March 17, Page 14-21

26 SVL90-2 ATTACHMENTS REPLACEMENT CAB & ROPS ADOPTION LIST SVL90-2 REPLACEMENT CAB & ROPS ADOPTION LIST Cab/ROPS # Model Cab/ROPS WG # 1 SVL90-2C Cab S SVL90-2CH Cab see chart 1 3 SVL90-2CF Cab see chart 2 SVL SVL90-2CHF Cab see chart 3 5 SVL90-2 ROPS S SVL90-2H ROPS see chart 4 7 SVL90-2F ROPS see chart 5 8 SVL90-2HF ROPS see chart 6 Chart 1 For Cab #2, order additional parts below Chart 2 For Cab #3, order additional parts below S6630 Part # SVL90-2CH QTY S6630 Part # SVL90-2CF QTY V Cover 1 V Switch 1 V Switch 1 V Label 1 Remove below part from the Cab Remove below part from the Cab R D Cap 1 V Switch 1 Chart 3 For Cab #4, order additional parts below Chart 4 For ROPS #6, order additional parts below S6630 Part # SVL90-2CHF QTY S6629 Part # SVL90-2H QTY V Cover 1 V Cover 1 V Switch 1 V Switch 1 V Switch 1 Remove below part from the ROPS V Label 1 R D Cap 1 Remove below part from the CAB RD V Cap 1 Switch 1 Chart 6 For ROPS #8, order additional parts below S6629 Part # SVL90-2HF QTY V Cover 1 V V Switch 1 V Label 1 Chart 5 For ROPS #7, order additional parts below Switch 1 S6629 Part # SVL90-2F QTY Switch 1 V V Label 1 Remove below part from the ROPS Remove below part from the ROPS RD Cap 1 V Switch 1 V Switch 1 Complete revision March 17, Page 14-22

27 SVL90-2 ATTACHMENTS PART 4 ACCESSORIES K9926 RETRACTABLE SEAT BELT OPTION (3 WIDE) 3 $80.00 As required in some states for OSHA compliance. S6679 Air Ride Seat Suspension Kit 55 $ S6677 Red Tail Light Kit 3 $ S6676 Strobe Light Kit 3 $ S6678 Rotating Beacon Light Kit 3 $ S6641 Rear View Mirror, includes Mounting Bracket & hardware $21.00 S6689 Hose Stay (Group hoses together at loader frame base) 3 $70.00 Recommend for use with: Brush Grapple, Scrap Grapple, SBB Hopper Sweeper, 4-in-1 bucket, and Tilt Attach ENCLOSURE KITS for ROPS S6681A Door Kit (Swing) with Frame and Wiper 170 $1, and Quick Glass Release Handles S6682 Sliding Side Window Kit 170 $ S6683A Heater Kit 16 $ S6684 Windshield Washer Kit 5 $ S6685 Circulation Fan Kit 25 $ S6687 Mounting Bracket for Magnetic Base 3 $60.00 PART 5 Available from Parts V Pin Attachment Coupler Kit V Engine Bonnet Lock Kit V Radiator Screen Kit Engine Block Heater Radio Kit Complete revision March 17, Page 14-23

28 SVL90-2 ATTACHMENTS PART 6 APPROVED ALLIED ATTACHMENTS MANUFACTURER S NUMBER Trencher Std Flow, model 625 with 36 boom, 6 cup type teeth, TES chain Trencher Std Flow, model 625 with 48 boom, 6 cup type Teeth, TES chain Trencher Hi-Flow, model 640 with 36 boom, 70/30 Shark/Cup teeth, TES chain Trencher Hi-Flow, model 640 with 48 boom, 70/30 Shark/Cup teeth, TES chain Dozer Blade Dozer Blade Tilt Attach (Recommend use of S6689 Hose Stay) Rotary Cutter (Std Flow) Gauge Wheels are optional Rotary Cutter (High Flow)Gauge Wheels are optional Cold Planer Model HP cutting width for SVL90/-2 Hi-Flow units only MX7H Power Rake MX7H, Std Flow Tiller (Std Flow) mechanical Offset, 6 tines Utility Brush Grapple (recommended for SVL Construction Brush Grapple (recommended for SVL E Snow Blower (Std Flow) (recommended for SVL90-2) LAF6786H Snow Blower (High Flow SVL90-2 only) LAF Snow Blade 20584M Hopper Sweeper (opt: nozzle kit & Gutter Brush) VRS7M VRS Pick-up (opt: nozzle kit & Gutter Brush) 22084M QC Angle Broom Std Flow (order angle kit separately 20085M QC Angle Broom High Flow = SVL90-2F only QCSS Hydraulic Angle Kit (with LAF Auger Drive - X HEX Drive, incl. mounting frame, Std Flow Rated at gpm Auger Drive - X HEX Drive, incl. mounting frame, Std Flow Rated at gpm Auger Drive - X HEX Drive, incl. mounting frame, Hi-Flow Rated at gpm CONTACT Bradco 503 Gay Street Delhi, IA (800) Fax (319) Harley 503 Gay Street Delhi, IA (800) Fax (319) FFC 503 Gay Street Delhi, IA (800) Fax (319) Sweepster 503 Gay Street Delhi, IA (800) Fax (319) McMillen 503 Gay Street Delhi, IA (800) Fax (319) Complete revision March 17, Page 14-24

29 SVL90-2 ATTACHMENTS PART 6 APPROVED ALLIED ATTACHMENTS (Cont.) MANUFACTURER S NUMBER Tree Spade 36" - Series Vibratory Roller - model: PD-VRP Rock Saw - RS24 (ONLY for SVL90-2 Hi-Flow) Root Rake w/grapple Skid Swing Hoe Tree Forks Post Driver - model: PD4800 LAF Tree Scoop 48" Concrete Claw LAF Soil Preparator Side Discharge Bucket 72" High Volume Heavy Duty Snow Bucket - 108" LAF Auto Rake - 84" CONTACT Paladin/Bradco 503 Gay Street Delhi, IA (800) Fax (319) Paladin/FFC 503 Gay Street Delhi, IA (800) Fax (319) For Auger Bit selection, please consult the Paladin catalog, as there is a wide variety of size, shapes, and applications. Complete revision March 17, Page 14-25

30 COMPACT TRACK LOADERS REPLACEMENT ENGINES V3307DT3CQ Replacement Engine for SVL75 with A/C TBA $8, V3307DT3CT Replacement Engine for SVL75 without A/C TBA $8, V3800DT3LQ Replacement Engine for SVL90 with A/C TBA $9, V3800DT3L6 Replacement Engine for SVL90 without A/C TBA $9, V33TE4QBB Replacement Engine for SVL75-2 with A/C TBA $12, V33TE4BB Replacement Engine for SVL75-2 without A/C TBA $12, V38CRTE4L Replacement Engine for SVL90-2 with A/C TBA $14, V38CRTE4L6 Replacement Engine for SVL90-2 without A/C TBA $14, Complete revision March 17, Page 14-26