8F.1. MUELLER / McCULLOUGH THERMAL-COIL METER BOX 8F-PVC/BOXES/VAULTS

Size: px

Start display at page:

Download "8F.1. MUELLER / McCULLOUGH THERMAL-COIL METER BOX 8F-PVC/BOXES/VAULTS"

Georgiana Warner
6 years ago
Views:

1 MUEE / McCUOUGH THEM-COI METE OX 8.1 The MUEE / McCullough THEM-COI Meter ox provides a means to allow a meter to be read and maintained even though it is set deep in the ground to resist freezing. The THEM-COI Meter ox is designed with the meter installed on a platform that normally sets near the bottom of the box where the ground temperature keeps it warmer. The meter and platform are connected to the service line by coils of polybutylene tubing which allow the meter and platform to be raised to the surface. The body of the meter box is made from rigid PVC which has a high insulating "" value to resist frost bridging inside the box. or extremely cold climates, an optional insulating pad is available which traps the relatively warm air rising from the earth inside the box. MUEE / McCullough THEM-COI Meter oxes are shipped fully assembled, ready for meter installation. Their light weight saves shipping costs and makes installation a one man job in most cases. Every box is factory tested and has a 150 psig maximum working pressure rating. MUEE / McCullough THEM-COI Meter oxes are available for 5/8" to 1" meters. wide variety of end connections, control valves, box depths, lids and other options provide you with the meter set you need. Due to the almost endless combination of features available, each box is custom built to your specifications. ee page 8.2 for options and ordering instructions. Manufactured under one or more of the following: U.. Patent No. 4,614,113; 4,813,281 MUEE / McCullough THEM-COI Meter ox eatures igid.300 minimum wall PVC material holds shape and resists frost bridging Optional insulation pad traps earth s heat to prevent freezing in extremely cold climates White interior aids visibility Meter set is anchored to moveable platform to maintain alignment and stability Platform support and reinforcing ring add rigidity to box Poly coil tubing provides low friction loss equivalent to a typical conventional meter set of the same size and depth Male I.P. thread inlet and outlet connections accept a variety of MUEE ervice ittings--see section 6 Optional aluminum bottom available arge selection of optional lids Typical Installaitons 8-PVC/OXE/VUT MUEE Valves and Couplings used in these meter box assemblies are manufactured and tested in accordance with NI/WW C800.

2 8-PVC/OXE/VUT 8.10 id rame id frames are used when boxes are installed in concrete or asphalt rame id ize Part No. Opening MUEE /McCUOUGH METE OX ETTE ID & ID KEY ox Dia. rame its " 15" & 18" " 18" 21" 24" & 27" NOTE: The frame adds 4" of height to the meter box. lat lid with side mounted standard waterworks pentagon nut lock id Part " " id ize lat lid--no lock id Part " " id ize NOTE: These lids cannot be used with lid frames lat lid with side mounted key lock and reader lid id Part " " id ize lat lid with side mounted key lock id Part " " id ize lat lid with side mounted standard waterworks pentagon nut lock and reader lid id Part " " id ize lat lid with center mounted MUEE pentagon nut lock lat lid -- no lock with reader lid id Part " " id ize NOTE: These lids cannot be used with lid frames id Part " " id ize id keys H H Multiple wrench-fits both MUEE pentagon and standard waterworks pentagon nuts. Not furnished with boxesorder Key handle - fits "key" lock lids and is used to unlock and lift lid. Not furnished with boxes - order Touch ead feature is available. Contact Customer ervice Center for price and availability.

These pads are made from a closed cell foam poly material that provides excellent insulating qualities and resists moisture absorption.

3 MUEE / McCUOUGH METE OX ETTE ID 8.9 Thermal shells Thermal shells are meter setter boxes only and do not include any fittings. The shells are available with a "V" notch option to allow service lines access to shell interior. Insulating pad Insulating pads are available in 2" and 4" thicknesses. These pads are made from a closed cell foam poly material that provides excellent insulating qualities and resists moisture absorption. Meter setter box diameter 2" Thick pad 4" Thick pad 15" " " " " Catalog Diameter X hell hell depth with V notch Catalog hell hell with V notch Diameter X depth O1512 V "X12" O2122 V "X22" O1514 V "X14" O2124 V "X24" O1516 V "X16" O2126 V "X26" O1518 V "X18" O2128 V "X28" O1520 V "X20" O2130 V "X30" O1524 V "X24" O2136 V "X36" O1526 V "X26" O2142 V "X42" O1528 V "X28" O2148 V "X48" O1530 V "X30" O2154 V "X54" O1812 V "X12" O2160 V "X60" O1814 V "X14" O2424 V "X24" O1816 V "X16" O2426 V "X26" O1818 V "X18" O2428 V "X28" O1820 V "X20" O2430 V "X30" O1822 V "X22" O2436 V "X36" O1824 V "X24" O2442 V "X42" O1826 V "X26" O2448 V "X48" O1828 V "X28" O2454 V "X54" O1830 V "X30" O2460 V "X60" O1836 V "X36" O2724 V "X24" O1842 V "X42" O2730 V "X30" O1848 V "X48" O2736 V "X36" O2112 V "X12" O2742 V "X42" O2114 V "X14" O2748 V "X48" O2116 V "X16" O2754 V "X54" O2118 V "X18" O2760 V "X60" O2120 V "X20" Meter setter box extensions Meter setter box dia. Meter setter box extensions are made from the same material and has the same wall thickness as the shell it will be set on. The lower end of the extension has guides attached to keep the extension properly centered. The top of the extensions are prepared to accept lids as illustrated on page 8.10*. Extension length 2" 4" 6" 8" 10" 12" 15" E1502 E1504 E1506 E1508 E1510 E " E1802 E1804 E1806 E1808 E1810 E " E2102 E2104 E2106 E2108 E2110 E " E2402 E2404 E2406 E2408 E2410 E " E2702 E2704 E2706 E2708 E2710 E " E3002 E3004 E3006 E3008 E3010 E3012 * NOTE: pecify the lid part to be used with the extension ordered. 8-PVC/OXE/VUT

The factory pre-aligned setter is stabilized to prevent shifting during backfilling. This makes it easier and more efficient to install or change out meters at a later time.

4 MUEE / McCUOUGH EZ-VUT METE ETTE 8.7 The MUEE / McCullough EZ-VUT Meter etters provide a means to quickly install a 1-1/2" or 2"meter. The EZ-VUT permits cities and water companies to standardize larger meter sets increasing convenience and efficiency during construction. The factory pre-aligned setter is stabilized to prevent shifting during backfilling. This makes it easier and more efficient to install or change out meters at a later time. The EZ-VUT Meter etter eliminates on-site fabrication and construction, saving time, material and labor costs. MUEE / McCullough EZ-VUT Meter etters are shipped fully assembled, ready for meter installation. Their light weight saves shipping costs and makes installation a one man job in most cases. Every box is factory tested and has a 150 psig maximum working pressure rating. bove box shown with optional lid ring and lid and is sectioned to illustrate valves and fittings. The MUEE / McCullough EZ-VUT Meter etter is available for 1-1/2" and 2" meters. wide variety of end connections, control valves, box depths, lids and other options provide you with the meter set the way you want it. Due to the almost endless combination of features available, each box is custom built to your specifications. ee page 8.8 for ordering instructions. Manufactured under one or more of the following: U.. Patent No. 4,614,113; 4,813,281 MUEE / McCullough EZ-VUT Meter etter eatures igid.486 minimum wall PVC material holds shape and resists frost bridging ightweight - can be handled by one man in most cases White interior aids visibility PVC brackets attached to shell stabilize brass meter risers or 1-1/2" and 2" meters Optional insulation pad traps earth s heat Male I.P. thread inlet and outlet connections accept a variety of MUEE ervice ittings--see section 6 Optional aluminum bottom available 150 psig maximum working pressure Typical Installation 8-PVC/OXE/VUT MUEE Valves and Couplings used in these meter box assemblies are manufactured and tested in accordance with NI/WW C800.

5 8-PVC/OXE/VUT 8.8 MUEE / McCUOUGH EZ-VUT METE ETTE MUEE / McCullough EZ-VUT Meter etter ordering instructions To order a MUEE / McCullough EZ-VUT Meter etter, simply choose the options you require from the seven catagories listed below and place the option code on the appropriate line of the catalog shown below. If you require options not listed, please fill out the information box shown below the options listing and contact the factory for price and delivery information. Phone or fax Catalog (1) (2) (3) (4) (5) (6) (7) 1Meter ize NOTE: Meter is not furnished Order neter Meter size 1-1/2" 500 2" Meter inlet langed lockwing angle meter stop langed lockwing angle ball valve (full port) 2 ox style 3 ox diameter ox style ingle meter ingle meter with by-pass ox diameter 24" box is for use with: 1-1/2" single flanged meter with or without by-pass 27" box is used with: 2" single flanged meter with or without by-pass V V Meter outlet 7 ox bottom Meter outlet langed meter coupling langed dual check valve langed lockwing angle stop meter langed lockwing angle ball valve (full port) ottom ttached aluminum bottom ess bottom 4 ox depth Depth Depth 30" 30 48" 48 36" 36 54" 54 42" 42 60" 60 pecial requirements order information Please specify special requirements and include drawing or photo if possible: MUEE Valves and Couplings used in these meter box assemblies are manufactured and tested in accordance with NI/WW C800.

6 8-PVC/OXE/VUT 8.6 MUEE /McCUOUGH EZ-ETTE METE OX MUEE / McCullough iser EZ-ETTE Meter ox ordering instructions To order a MUEE / McCullough iser EZ-ETTE Meter ox, simply choose the options you require from the eight catagories listed below and place the option code on the appropriate line of the catalog shown below. If the box you need is a tandem, please fill out the tandem information box shown below the options listing and contact the factory for price and delivery information. Phone or fax Catalog (1) (2) (3) (4) (5) (6) (7) Options 1 Meter size NOTE: Meter is not furnished. Order meter Meter size 5/8" 200 5/8"x3/4" 203 3/4" 250 1" ox style ox style ingle meter 3 ox diameter Double meter Tandem D T ox diameter 18" box is for use with: 5/8, 5/8x3/4, 3/4, 1 single meters 5/8, 5/8x3/4, 3/4 tandems 18 5/8, 5/8x3/4 or 3/4 double meters 21" box is used with: 1tandems 21" 5 6 Meter outlet 7 ox bottom ockwing angle meter stop ockwing angle ball valve ( full port ) ockwing angle ball valve ( reduced port ) Meter outlet Meter coupling Dual check valve...e. Dual check...e. Top entry vertical check ockwing angle meter stop ockwing angle ball valve ( full port ) ockwing angle ball valve ( reduced port ) ottom ttached aluminum bottom ess bottom V 4 ox depth Depth Depth 14" 14 21" 21 15" 15 22" 22 16" 16 23" 23 17" 17 24" 24 18" 18 25" 25 19" 19 26" 26 20" 20 8 Type of box locking device (box is ordered with device to accept either a non-locking lid, center locking or side locking lid). ids must be ordered ock Non-locking Center locking ide locking N Tandem box order information Type of tandem device (regulator, backflow preventer etc) ize and length of tandem device Tandem device manufacturer's name Tandem device model NOTE: Tandem device is not furnised and must be ordered MUEE Valves and Couplings used in these meter box assemblies are manufactured and tested in accordance with NI/WW C800.

These meter boxes can also be ordered for double meter sets or tandem sets for meter and regulator or meter and backflow preventer.

7 MUEE / McCUOUGH IE EZ-ETTE METE OX 8.5 The MUEE / McCullough iser EZ-ETTE Meter ox provides a means to quickly install a meter. To make the meter more accessible in deeper boxes, the meter is set on a riser which positions it closer to ground level. The iser EZ-ETTE comes pre-assembled, tested and ready to install. These meter boxes can also be ordered for double meter sets or tandem sets for meter and regulator or meter and backflow preventer. The body of the meter box is made from rigid PVC which has a high insulating "" value to resist "frost bridging" inside the box. or extremely cold climates, an optional insulating pad is available which traps the relatively warm air rising from the earth, to keep the meter set from freezing. bove box shown with optional aluminum bottom and is sectioned to illustrate valve and fitting. MUEE / McCullough iser EZ-ETTE Meter oxes are shipped fully assembled, ready for meter installation. Their light weight saves shipping costs and makes installation a one man job in most cases. Every box is factory tested and has a 150 psig maximum working pressure rating. MUEE / McCullough iser EZ-ETTE Meter oxes are available for 5/8" to 1" meters. wide variety of end connections, control valves, box depths, lids and other options provide you with the meter set that you want. Due to the almost endless combination of features available, each box is custom built to your specifications. ee page 8.6 for ordering instructions. Manufactured under one or more of the following: U.. Patent No. 4,614,113; 4,813,281 MUEE / McCullough iser EZ-ETTE Meter ox eatures igid.300 minimum wall PVC material holds shape and resists frost bridging Optional insulation pad traps earth s heat White interior aids visibility Meter set is anchored to meter box wall to maintain alignment and stability Male I.P. thread inlet and outlet connections accept a variety of MUEE ervice ittings--see section 6 Optional aluminum bottom available arge selection of optional lids Typical Installation 8-PVC/OXE/VUT MUEE Valves and Couplings used in these meter box assemblies are manufactured and tested in accordance with NI/WW C800.

8 MUEE / McCUOUGH EZ-ETTE METE OX 8.3 The MUEE / McCullough Inline EZ-ETTE Meter ox provides a means to quickly install a shallow set meter. The in-line EZ-ETTE comes pre-assembled, tested and ready to install. These meter boxes can also be ordered for double meter sets or tandem sets for meter and regulator or meter and backflow preventer. The body of the meter box is made from rigid PVC which has a high insulating "" value to resist "frost bridging" inside the box. or extremely cold climates, an optional insulating pad is available which traps the relatively warm air rising from the earth, to keep the meter set from freezing. bove box shown with optional aluminum bottom and is sectioned to illustrate internal valve and fitting. MUEE / McCullough Inline EZ-ETTE Meter oxes are shipped fully assembled, ready for meter installation. Their light weight saves shipping costs and makes installation a one man job in most cases. Every box is factory tested and has a 150 psig maximum working pressure rating. The MUEE / McCullough Inline EZ-ETTE Meter ox is available for 5/8" to 1" meters. wide variety of end connections, control valves, box depths, lids and other options provide you with the meter set that you want. Due to the almost endless combination of features available, each box is custom built to your specifications. ee page 8.4 for ordering instructions. Manufactured under one or more of the following: U.. Patent No. 4,614,113; 4,813,281 MUEE / McCullough Inline EZ-ETTE Meter ox eatures igid.300 minimum wall PVC material holds shape and resists frost bridging Optional insulation pad traps earth s heat White interior aids visibility Meter set is anchored to meter box wall to maintain alignment and stability Male I.P. thread inlet and outlet connections accept a variety of MUEE ervice ittings see section 6 Optional aluminum bottom available arge selection of optional lids Typical Installation 8-PVC/OXE/VUT MUEE Valves and Couplings used in these meter box assemblies are manufactured and tested in accordance with NI/WW C800.

9 8-PVC/OXE/VUT 8.4 MUEE / McCullough Inline EZ-ETTE Meter ox ordering instructions MUEE / McCUOUGH EZ-ETTE METE OX To order a MUEE / McCullough Inline EZ-ETTE Meter ox, simply choose the options you require from the eight catagories listed below and place the option code on the appropriate line of the catalog shown below. Contact the factory for price and delivery information for double and tandem boxes and other options not listed. Phone or fax (1) (2) (3) (4) (5) (6) (7) (8) Options 1 Meter size NOTE: Meter is not furnished and must be ordered 2 ox style Meter size 5/8" 200 5/8"x3/4" 203 3/4" 250 1" 330 ox style ingle meter I 5 6 Meter outlet ockwing meter valve ockwing ball valve ( full port ) ockwing ball valve ( reduced port ) Meter outlet Meter coupling Dual check valve *...E. Dual check valve * ockwing meter valve * ockwing ball valve ( full port ) * ockwing ball valve ( reduced port ) * 3 ox diameter 4 ox depth ox diameter 15" box with meter coupling outlet for use with: 5/8, 5/8x3/4 single meters 18" box with meter coupling outlet for use with: 3/4, 1 single meters 18" box with lockwing meter valve or dual check valve outlet for use with: 5/8, 5/8x3/4 or 3/4 single meters 21" box with lockwing meter valve or dual check valve outlet for use with: 1single meters Depth Depth 10" 10 15" 15 11" 11 16" 16 12" 12 17" 17 13" 13 18" 18 14" ox bottom Type of box locking device (box is ordered with device to accept either a non-locking lid, center locking or side locking lid). ids must be ordered ottom ttached aluminum bottom ess bottom ock Non-locking Center locking ide locking N * These meter outlet s may require using larger size box. Contact MUEE Customer ervice Center for more details. MUEE Valves and Couplings used in these meter box assemblies are manufactured and tested in accordance with NI/WW C800.

10 8-PVC/OXE/VUT 8.2 MUEE / McCullough THEM-COI Meter ox ordering instructions To order a MUEE / McCullough THEM - COI Meter ox, simply choose the options you require from the eight catagories listed below and place the option code on the appropriate line of the catalog shown below. Catalog (1) (2) (3) (4) (5) (6) (7) (8) MUEE /McCUOUGH THEM-COI METE OX If the box you need is a tandem, please fill out the tandem information box shown below the options listing and contact the factory for price and delivery information. Phone or fax Options 1 Meter size NOTE: Meter is not furnished. Order meter Meter size 5/8" 200 5/8"x3/4" 203 3/4" 250 1" ockwing angle meter stop ockwing angle ball valve (full port) ockwing angle ball valve (reduced port) 2 ox tyle 3 ox diameter ox style ingle meter Double meter Tandem ox diameter 15" box is for use with: 5/8, 5/8x3/4 or 3/4 single meters 5/8, 5/8x3/4 or 3/4 tandems * 18" box is for use with: 1" single meters 1" tandems 5/8, 5/8x3/4 or 3/4 double meters C CD CT Meter Meter outlet 7 outlet ox bottom Meter coupling Dual check valve...e. Dual check valve...e. Top entry vertical check ockwing angle meter stop ockwing angle ball valve (full port ) ockwing angle ball valve ( reduced port) ottom ttached aluminum bottom ess bottom V 4 ox depth Depth Depth 30" 30 66" 66 36" 36 72" 72 42" 42 78" 78 48" 48 84" 84 54" 54 90" 90 60" 60 96" 96 8 Type of box locking device (box is ordered with device to accept either a non-locking lid, center locking or side locking lid). ids must be ordered ock Non-locking Center locking ide locking N Tandem box order information Type of tandem device (regulator, backflow preventer etc) ize and length of tandem device Tandem device manufacturer's name Tandem device model * NOTE: Tandem device is not included and must be purchased O, 3/4" tandems systems when used with certain regulators may need to be placed within a 18" box; list the regulator model when specifying this system. If an E check valve or ball valve is being used in a 3/4" setting then an 18" meter box will be required. MUEE Valves and Couplings used in these meter box assemblies are manufactured and tested in accordance with NI/WW C800.

8F. MUELLER / HUNT THERMAL-COIL METER BOX. 8F-PVC/bOXES/VAULTS

8F. MUELLER / HUNT THERMAL-COIL METER BOX. 8F-PVC/bOXES/VAULTS MUEE / HUNT THEM-COI METE OX 8. The MUEE / Hunt THEM-COI Meter ox provides a means to allow a meter to be read and maintained even though it is set deep in the ground to resist freezing. The THEM-COI Meter