J e t t i n g n o z z l e s

Transcription

1 J e t t i n g n o z z l e s Setting the standard Overview jetting nozzles Jetting nozzles For each type of high pressure machine For drains up to 600 mm Highest efficiency For all kind of blockages Radial or rotating With or without front jet Stainless steel or tempered steel With or without (ceramic) insert nozzles Matching hoses and hose inlet guidance tubes and rollers

2 Rioned can supply jetting nozzles for any type of high pressure jetting machine and has an extensive range of jetting nozzles in all types and sizes; suitable for a diversity of blockages in drains up to 600 mm. Highest efficiency A good jetting nozzle contributes to a maximum efficiency of high pressure jetting machines. This means: thorough cleaning, optimal rinsing effect, high to very high traction, minimal loss of pressure, short cleaning time, high performance velocity from water jets, low friction resistance, no damage to sewer pipes. Rioned supplies jetting nozzles that meet the highest efficiency demands. For all kind of blockages Each cleaning job requires a specific approach. That is why Rioned has a diverse range of jetting nozzles. Because of the design, some are better for unblocking, others for cleaning the drain wall. Radial jetting nozzles for example, usually perform well in unblocking: the static jet streams increase the traction. Rotating jetting nozzles on the other hand spray in all directions and are the best drain cleaners. They are often used to do some extra cleaning after unblocking a drain, to prevent new blockages. Some jetting nozzles are made for obstructions in or around the house that are caused by deposits of grease or soap. Others are armed with chains or steel wires to handle the most difficult jobs like the descaling of lime, cement or concrete, hard grease and smaller roots. Rioned also has several special jetting nozzles in its assortment for very specific situations, like root cutters and sand shoes. Open or blind An open jetting nozzle has forward and rear facing holes. The forward jet streams do the unblocking and the rear jet streams provide traction. A blind jetting nozzle has rear facing holes only for the best traction. Stainless steel or tempered steel Rioned jetting nozzles are super solid. They are made of stainless or tempered steel. Only the sand shoes are made out of another material: the small ones out of the relatively light weight aluminium and the bigger ones are of bronze so that they are heavy enough to stay at the bottom of a sewer. Insert nozzles Most jetting nozzles have insert nozzles that can be replaced. After a while the holes (the nozzles) wear out because of the water power. Then the jetting nozzle loses pressure. The lifetime of a jetting nozzle can be increased substantially by replacing the insert nozzles. There are steel as well as ceramic insert nozzles. Those with the ceramic inner layer are even more resistant to wear. Radial jetting nozzles Standard jetting nozzle Rioned delivers standard nozzles with each new high pressure jetting machine. They belong to the basic equipment and are mainly used for working on deposits of grease and soap in pipes in or around the house. S31 jetting nozzle The shorter version of the Standard jetting nozzle; also meant for unblocking pipes in or around the house. It has a strong jet stream for good cleaning. However, the S31 can move through curves and smaller pipes better because of its shorter length. Front jetter This jetting nozzle has only 1 front jet and no jet stream backwards. Therefore it is best used to clean wells and pumps or to push forward the sludge through the pipes. Diameter mm Length mm Design stainless steel, open and blind Flow range lpm / 2-27 gpm Connection 1/8, 1/4, 3/8, 3/4, 1/2, 1 Usage drains with Ø mm Diameter 34 mm Length 31 mm 90º-curves starting from 110 mm Design stainless steel, open and blind Flow range lpm / 7-27 gpm Usage drains with Ø mm Diameter 28 mm Length 85 mm 90º-curves starting from 90 mm Design precious steel, blind (no holes at the rear) Water flow lpm / 7-89 gpm Pressure max. 200 bar / 2900 psi High yield jetting nozzle Combines traction with cleaning capacity. Its high yield comes from a built-in chamber that limits the loss of pressure in the jetting nozzle. Its cleaning capacity comes from two spray rings giving jet streams at different angles. Diameter 38 mm Length 46 mm Design stainless steel, open and blind Water flow lpm / 9-27 gpm Usage drains with Ø mm 90º-curves starting from 110 mm Matching hoses and hose inlet guidance tubes and rollers Several circumstances contribute to the efficiency of a jetting nozzle. For example the size of the jetting nozzle compared to the size of the drain that has to be cleaned and the power of the pump (pressure and litres / minute). Very important, but often forgotten, is the hose. Its length and diameter can improve or interfere with the performance of the jetting nozzle. The correct length and diameter of the hose determines performance. That is why Rioned also supplies matching hoses in a good quality: reliable, smooth, flexible and durable. To avoid hose damage at the entrance of a drain, there are also several types of hose inlet guidance tubes and rollers available. Sand shoe Designed to clear away sand and stones. Because of their shape, they remain flat on the bottom of the sewer. Therefore they are extremely suitable to clean the bottom of wider drains. They are capable to replace many times their own weight of sand and stones. To achieve the highest efficiency, always use a sand shoe in combination with a rotating coupling. Width mm Length mm (without coupling) Design aluminium / bronze, open Water flow lpm / 7-89 gpm Pressure max. 200 bar / 2900 psi, 3/4, 1 Usage drains with Ø starting from 250 mm 90º-curves starting from 250 mm

3 Nozzle sets Rocket jetting nozzle black A jetting nozzle with a huge traction and very powerful jet streams that make it ideal for longer pipes. It is also available with a front jetter. Diameter 60 mm Length 120 mm Design tempered steel, open with insert nozzles Water flow lpm / 9-27 gpm Usage drains with Ø mm 90º-curves starting from 200 mm Rioned has two complete jetting nozzle sets available for those who always want to have the right tools at hand for all kind of blockages: the Basic and the Professional. The Basic contains all jetting nozzles that everybody should have. The Professional is for more difficult jobs and is equipped with jetting nozzles for bigger and more powerful high pressure jetting machines. Granate jetting nozzle A standard jetting nozzle for pipes with a bigger diameter. It also has an excellent traction. Diameter 50 mm Length 75 mm Design stainless steel, open with insert nozzles Water flow lpm / 9-27 gpm Torpedo jetting nozzle It looks like the Granate jetting nozzle, but is much bigger and is made for wider pipes. The Torpedo has more jets at the rear for even more traction. Usage drains with Ø mm Diameter 75 mm Length 125 mm 90º-curves starting from 150 mm Design stainless steel, open with insert nozzles Water flow lpm / 9-89 gpm Connection 1 (if necessary adapter ring 1 to 1/2 or 3/4 ) Usage drains with Ø mm 90º-curves starting from 200 mm The Basic contains: Two mini jetting nozzles 1/8 (open and blind) suitable for a mini high pressure jetting hose S31 High efficiency jetting nozzle Front jetter Granate jetting nozzle Quatro set Rotating jetting nozzle stainless steel Nozzle needles Universal lubricating oil Quatro set jetting nozzle The tapering jetting nozzle that is best for difficult obstructions. It cuts, breaks and and removes them. The Quatro set is also the best solution for ice in the pipes. Diameter mm Length mm Design tempered steel, open Water flow lpm / 4-89 gpm Connection 1/8, 1/4, 1/2, 3/4, 1 Usage drains with Ø mm 90º-curves (depending on the size) starting from 50 mm The Profiset contains: Two mini jetting nozzles 1/8 (open and blind) suitable for a mini high pressure jetting hose S31 High efficiency jetting nozzle Front jetter Rotating jetting nozzle tempered steel Tornado Quatro set Torpedo Sand shoe Nozzle needles Universal lubricating oil

4 Rotating jetting nozzles Standard rotating jetting nozzle stainless steel Rotating jetting nozzle that cleans away deposits of soap and grease and leaves drains streak-free. Standard rotating jetting nozzle tempered steel Rotating jetting nozzle made of tempered steel with ceramic insert nozzles. Diameter 40 mm Length 85 mm Design stainless steel, steel insert nozzles Water flow lpm / 9-27 gpm Usage drains with Ø mm 90º-curves starting from 110 mm Diameter 40 mm Length 85 mm Design stainless steel,ceramic insert nozzles Water flow lpm / 2-89 gpm Connection 1/8, 1/4, 3/8, 1/2 Usage drains with Ø mm 90º-curves starting from 110 mm Tornado jetting nozzle The super unblocker. This jetting nozzle has a special construction with a rotating ceramic part so that the water comes out in the form of a cone. This cone drills away any obstructions. At the same time the Tornado has an excellent traction. Diameter 39 mm Length 64 mm Design stainless steel, open with insert nozzles Water flow lpm / 7-27 gpm Usage drains with Ø mm 90º-curves starting from 110 mm An ideal couple Equipped with the Tornado and the Blizzard you can solve nearly all obstruction problems! Mini Small Large Extra Large Diameter mm Length mm Design stainless steel, open Water flow lpm Blizzard jetting nozzle The all-in-one jetting nozzle. With its hydraulic tempered front jet it drills itself through blockages. The rotating partition prevents spinning and limits the spraying of the water. Therefore the Blizzard has more power and is capable to clean the whole drain wall. It is available in four different sizes and with attachment to extend or centralize the jetting nozzle: the Centralizer and the Super Centralizer lpm lpm lpm 3-10 gpm 6-17 gpm 9-33 gpm gpm Pressure 275 / / / / 3000 bar/psi Connection 3/8 1/2 1/2 or 3/4 1 Usage drains with Ø mm 90º-curves starting from: 75 mm 110 mm 250 mm 300 mm Rotation speed rpm Buster jetting nozzle Made for the most difficult obstructions, but relatively light-weight. It hits, cuts and scrapes through everything. The Buster is delivered as a set with a body and three jetting nozzles provided with: Link chains for hardened blockages (limescale, cement or concrete) Industrial chains, sharp enough to tackle grease or smaller roots Steel wires to scrape the pipes clean. The set also contains a cutting point to drill through blockages. Diameter 50 mm Length 65 mm Design tempered stainless steel, open and blind Water flow lpm / 7-27 gpm Pressure bar / psi Usage drains with Ø mm 90º-curves starting from Ø 90 mm Rotation speed depending on the capacity of the machine

5 Hydraulic root cutter The best solution for drains that are blocked by roots, hard grease, compacted sand or soil. The Rioned root cutters are powerful, reliable and easy to use. They consist of a central body with knives in different sizes and matching skids to keep them centralized in the drain. The knives have sharp angular teeth at front and rear. Rioned supplies two types: there is a standard root cutter as well as the Maxi. The Maxi is for high pressure jetting machines and combination units with more water flow and bigger connections. All root cutters come as a complete set in a carrying box. Each set contains: standard knives standard skids transport box grease/waternipple mounting set grease gun Hydraulic root cutter Hydraulic root cutter Maxi Diameter starting from 100 mm starting from 150 mm Length 200 mm (knife included) 310 mm (knife included) Design knives tempered steel tempered steel open open Water flow lpm / 9-27 gpm lpm / gpm Pressure max. 140 bar / 2100 psi max. 140 bar / 2100 psi 3/4, 1 Usage drains with Ø mm drains with Ø mm Standard knives Ø 100, 150 or 200 mm Ø 150, 200, 250, 300 or 375 mm Optional knives Ø 125, 225 or 250 mm Standard skids Ø 100, 150 or 200 mm Ø 150, 200, 250, 300 or 375 mm Optional skids Ø 125, 225 or 250 mm Maxi High pressure hoses The high pressure hose has to be adjusted to the water flow and the pressure of the machine. That is why for each high pressure jetting machine, Rioned gives advice about the length and the (inside) diameter of the hose. Do always follow this advice in order to obtain the highest efficiency of the machine and the jetting nozzle. In longer hoses, the water gets more resistance; using a hose that is too long, therefore causes an unnecessary loss of pressure. If the hose is too narrow, there is a loss of pressure too. And if the hose is too wide for the machine (a wrong inside diameter), the jet stream also loses power. Rioned supplies reliable and smooth hoses in different sizes. They are special hoses for cleaning work, very flexible, resistant to high pressure, and fit for drains with a diameter up to 600 mm. These hoses are made of a flexible rubber compound and all have a steel inside coating to make them even more reliable and resistant to wear. The outside is smooth so that they have less resistance and are more hygienic than for example textile hoses. Inside diameter Length Coupling NW 5 (= 3/16 ) 10, 15 or 20 m 1/8 x 1/8 NW 6 (= 1/4 ) 10, 15 or 20 m 1/8 ext. 3/8 int. NW 8 (= 5/16 ) 10, 20 or 30 m 1/4 x 3/8 NW 10 (= 3/8 ) 20, 30, 40 or 50 m 2 x 1/2 NW 13 (= 1/2 ) 20, 40, 50, 60, 80, 100 or 120 m 2 x 1/2 NW 16 (=5/8 ) 80, 100 or 120 m 2 x 1/2 other lengths on request. Hose inlet guidance Often a hose has to be pass sharp edges at the entrance or the inside of a drain. The hose scrapes along these sharp edges, which causes unnecessary wear. This happens also inside the drain, at the link between the vertical and the horizontal pipes. Special accessories have been developed to prevent such damage: the hose inlet guidance tubes and rollers. Rioned supplies them in different types: A metal guidance that is put over the edges of the train, protecting the hose at the inlet of the drain. A metal guidance that can be brought into the drain to guide the hose at the bottom of the drain. This guidance protects the hose at the link between the vertical and the horizontal pipes. A plastic guidance that is also led into to the drain to protect the hose at the bottom of the drain. For most of them the principal is the same: nylon rollers guide the hose into the drain so that it does not touch the edges. The inlet guidance s are suitable for are all Rioned high pressure hoses: from NW 5 until NW 16.

6 Basic rules for using the right jetting nozzle 1. Choose the jetting nozzle that best fits the application. The schedule below shows which one is best suited for which type of work. Cleaning Unblocking Sand Hardened Ice in drains Roots Washing drain walls grease and deposits (lime wells and soap concrete, pumps cement etc.) Standard jetting nozzles S31 Front jetter High yield jetting nozzle Rocket jetting nozzle black Granate Torpedo Quatro set Standard rotating jetting nozzle Tornado Buster Blizzard Root cutter Sand shoe Not fit Possible Best solution 2. Check which function the jet streams need to have. Do they have to unblock, clean or provide traction? A strong jet stream forward will unblock well and drills a hole through difficult obstructions. When cleaning from the building, a strong jet stream forward is necessary to move the dirt forwards. A strong jet stream backward gives traction. When cleaning from the drain, a strong jet stream backward is necessary to pull back the dirt. Sideways jet streams spray into the direction of the drain walls and are best fit to clean. 3. Check the right size of the jetting nozzle If a jetting nozzle is too small, it does not clean very well and it can easily turn around inside a pipe. A jetting nozzle that is too big can not take angles. As a basic rule, we advise a jetting nozzle with a diameter that is about 1/4 of the drain that has to be cleaned. To prevent problems in curves, never use a jetting nozzle that is longer than the diameter of the drain. 4. Check the capacity of the pump The hose and the jetting nozzle need a certain water flow. Always check if the pump is capable of delivering enough water for optimal use of the jetting nozzle. Rior B.V./Rioned is the European market leader in cleaning, detection and inspection systems for small and medium-sized drains and sewers. From the head office in Tilburg (the Netherlands) as well as the affiliates in the UK, France and Belgium, worldwide markets are served. 5. Check the nozzles The pump presses the water with power through the nozzles (the holes in the jetting nozzle). This is what causes the water pressure. If the nozzles are too small, too much pressure is caused which damages the pipes. If they are too big, not enough pressure is built up for doing the job well. Always take care that for each machine a good jetting nozzle with the right holes is used. It is also recommended to check the holes regularly on wear and blockages. 6. Adjust the jetting nozzle to the hose and the connection It goes without saying that the jetting nozzle has to fit on the coupling. If the diameter of the hose is too small, it is too flexible and it can turn around in the pipe while it is being used. All Rioned jetting nozzles are female; that is why they are as short as possible. When ordering a jetting nozzle always tell us the length, diameter and connection on the hose working pressure and litres of the pump Rior B.V./Rioned Postbus EB Tilburg Centaurusweg TC Tilburg Nederland Tel. +31 (0) Fax +31 (0) Rioned/Wards UK Limited 22 James Carter Road Mildenhall, Suffolk, IP28 7DE United Kingdom Tel. +44 (0) Fax +44 (0) sales@rionedwards.co.uk

7 B l i z z a r d The most powerful sewer jet nozzle Controlled rotation speed Pipes from mm Less jets, with more power per jet 15º front rotating jet Durable

8 B l i z z a r d The Blizzard is the most powerful sewer jet nozzle that exists. It works easily through fat, lime, sand, sludge, stones, smaller roots and other heavy blockages in the sewer or drainage system. Because of the small size, it is very usable in pipes from Ø 75 mm mm. The Blizzard is suitable for high pressure jetting machines from bar (2000 psi 6000 psi) and from 20 lpm lpm (4.5 gpm 66 gpm). Super powerful The powerful front rotating jet, spouts at an angle of 15º. The controlled rotation speed is unique. Uncontrolled fast rotation causes break up of jets, spraying of water and removes the cleaning power of the nozzle. The controlled rotation speed of the Blizzard does not mean loss of power. The Blizzard has less jets, but each jet is far more powerful. Thus, the traction as well as the cleaning power is increased. It is ideal for streak-free cleaning of the drain wall and the cutting of fat and smaller roots. In less than a minute, the blizzard can even cut a hole in a piece of pine wood. Centralizer Durable The Blizzard is made out of stainless steel and can be completely dismantled in order to replace parts. The Blizzard has nozzles with Attack Tip to concentrate the jet 4 types Flow range (lpm) (gpm) Max. Pressure (psi) (bar) Hose connection (npt) Rotation speed (OPM) Attachments The Blizzard can be delivered with attachments to extend or centralize the nozzle: the Centralizer and the Super Centralizer. They prevent the nozzle turning in drains and sewers with diameters larger than 200 mm. They also provide a better result because of the optimal distance between the front jet and the blockage. Technical Details BM-3/8 BK-1/2 BG-1/2 of BXG-1 BG-3/4 MINI SMALL LARGE EXTRA LARGE (3-10) (6-17) (9-33) (42-66) /8 1/2 1/2 1 of 3/ Super Centralizer Rior B.V./Rioned Postbus EB Tilburg Nederland Tel. +31 (0) Fax +31 (0) Rioned/Wards UK Limited 22 James Carter Road Mildenhall, Suffolk, IP28 7DE United Kingdom Tel. +44 (0) Fax +44 (0) sales@rionedwards.co.uk

9 B u s t e r Small rotating chain nozzle for great results Rotating chain nozzle Length 65 mm and diameter 50 mm With or without chains For drains from mm 90º-curves starting from 90 mm Usable with flows from 30 lpm (7 gpm) Durable

10 B u s t e r The Buster is the nozzle for the most heavy blockages. It is a rotating nozzle that makes quick work of the descaling of lime, cement or concrete, grease and smaller roots. A unique nozzle, because it not only distinguishes itself by its performances, but also by its small size. Small rotating chain nozzle for great results Most similar nozzles are often big and heavy. The Buster is only 65 mm long and has a diameter of 50 mm. Because of its small size, it has several advantages: relatively lightweight usable in drains from Ø 80 mm able to take right angles in drains from Ø 90 mm usable with smaller machines (starting from 80 bar (1200 psi) and a flow range from 30 lpm (7gpm) Durable The Buster is made of hardened stainless steel. Its insert nozzles are ceramic and therefore very solid. Furthermore, the Buster can be completely dismantled in order to replace parts Attachments The buster always is delivered as a kit in a suitcase. Apart from the body, the set consists of three different nozzles. They are provided with: link chains for hardened blockages; to smash, for example, limescale, cement or concrete industrial chains, sharp enough to tackle grease or smaller roots. steel wires to scrape the pipes clean. The set also contains a cutting point to drill through blockages. Spare chains and spare steel wires are also included. Rior B.V./Rioned Postbus EB Tilburg Nederland Tel. +31 (0) Fax +31 (0) Flow range Pressure Hose connection Usage Rotation speed Technical Details litre per minute bar ( psi) 1/2 Drains with Ø from mm The number of rotations per minute depends on the capacity of the machine Rioned/Wards UK Limited 22 James Carter Road Mildenhall, Suffolk, IP28 7DE United Kingdom Tel. +44 (0) Fax +44 (0) sales@rionedwards.co.uk

11 R o o t C u t t e r s Cut any obstinate obstructions with ease Powerful hydraulic cutter High quality cutting knives Angular teeth at front and rear Exchangeable knives and skids Reliable and user-friendly

12 R o o t C u t t e r s Rioned hydraulic root cutters are the answer for problems with roots, hard grease, compacted sand, soil or other solid obstructions in drains and sewers from Ø 100 mm 350 mm. The Rioned Maxi Hydraulic root cutter goes up to drains and sewers of Ø 500 mm. Powerful and reliable The Rioned hydraulic root cutters are characterised by their power, reliability and simple operation. They are very effective. The Rioned Maxi hydraulic root cutter is specially developed for high pressure jetting machines and combination units with larger water flows and hose connections. Knives of hardened steel All root cutters come as a complete set in a transport box. The cutting knives have angular teeth at front and rear for effective cutting results, while jetting both forward and backward. The knives of the standard hydraulic root cutter are made of special hardened steel. Type Maxi Equipment for all root cutters The Rioned root cutter standard equipment: Standard cutting knives Standard skids Transport box Grease/water nipple Mounting set Grease gun Optional for the hydraulic root cutter Extra knives Extra skids Rior B.V./Rioned Postbus EB Tilburg Nederland Usage (drains Ø mm) Flow range (lpm/gpm) Max. Pressure (bar/psi) Standard knives (Ø mm) Optional knives (Ø mm) Standard skids (Ø mm) Optional skids (Ø mm) Hose connection Weight (kgs) Length (mm) Technical details Hydraulic Root Cutter Hydraulic Maxi Root Cutter / / / / , 150 and , 200, 250, 300, , 225 and , 150 and , 200, 250, 300, , 225 and 250 1/2 3/4 and/or Tel. +31 (0) Fax +31 (0) Rioned/Wards UK Limited 22 James Carter Road Mildenhall, Suffolk, IP28 7DE United Kingdom Tel. +44 (0) Fax +44 (0) sales@rionedwards.co.uk

13 R i o p u l s e Gets more out of your HP machine Big improvement in performance Up to 80% water savings Easier to lead into long and difficult sewers Strong impact on severe blockages Suitable for nearly all HP machines Construction possible on existing machines

14 R i o p u l s e The Riopulse Pulsator system can be built on nearly all high pressure machines with a Speck/Rioned pump. The pulsator is a technical adjustment to the pump. It continuously interrupts the water flow and sends pulses of water through the hose. Water pressure remains constant. Improvement of efficiency Supply of water in pulses has many advantages and all contribute to more efficiency: Water is saved because a part of the water flows back into the tank. With the use of high pressure hoses in longer drains, these savings can go up to 80%. This means longer working with a full water tank and it is better for the environment, because as much water as possible is saved. Time is saved because high pressure hoses can be fed rapidly into difficult sewers: even a distance of a 150 meters is feasible. When the hose is completely lead in the drain, the pulsator can be switched off so that the full capacity of the machine is used to clean the sewer. The water and the capacity are saved until really necessary. Greater impact of the nozzle, especially on more severe blockages. The pulsator is fastened on one of the cylinders of the pump The pulsator can be operated easily with a handle The Riopulse Pulsator system can be constructed directly on new machines, as well as later on on existing machines. No effect on the life span of the pump This system does not effect the life span of the pump in any way! Rior B.V./Rioned Postbus EB Tilburg Nederland Tel. +31 (0) Fax +31 (0) Usable Pump Motor Technical details Pipes up to 150 m (depending on the hose and the pump) Rioned/Speck high pressure pump P30, most of the P41 types, P45 and P52 Can be used on machines with separate motor or PTO driven Rioned/Wards UK Limited 22 James Carter Road Mildenhall, Suffolk, IP28 7DE United Kingdom Tel. +44 (0) Fax +44 (0) sales@rionedwards.co.uk