CR5-H. Parts List & Kits. GRUNDFOS Industrial Service Manual. Contents

Transcription

1 GRUNDFOS Industrial Service Manual CR5-H Parts List & Kits Contents Parts List Spare Part Kits Accessories Special Tools Standard Tools Tools for Torques

2 Exploded View CR5-H

3 Parts List & Kits CR5-H Pos. parts list Part Description Model Stages Used Comments/Dimensions B.O.M. Ref. Material Adapter for Motor Stool 8-24 For NEMA, 23/25TC, HP No 2 Motor Stool 2/-6 NEMA, 56C, /3-2 HP No 7-6 NEMA, 82/84TC, 3-5 HP No 8-24 Add Pos., NEMA, 23TC, HP No 4 Chamber, Complete with Pos. 45 & 65 2/-36 ^^^ PTFE Pos No 2/-36 ^^^ PTFE Pos. 45 ( is qty of 24) No 4a Chamber Cpl. w/pos. 45 & 65 & Bearing 2/-36 ^^^^ Silicon Carbide Brg, PTFE Pos YES Chamber Cpl. w/pos. 45 & 65 & Brg. (option) 2/-36 ^^^^ Bronze Bearing, PTFE Pos YES 2/-36 ^^^^ Graflon Bearing, PTFE Pos YES 5a Chamber, Bottom Complete with Pos. 45 & 65 2/-36 * PTFE Pos No Chmb. Btm. Cpl. w/pos. 45 & 65 (Low NPSH opt.) 2/-36 PTFE Pos No 6 Base 2/-36 GA, Cast Iron No 7 Coupling Guard 2/-6 2 NEMA, 56C YES NEMA, 82-25TC YES 7a Screw for Coupling Guard 2/-36 4 Screw comb. slot torx/straight slot 4 x 8mm YES 9 Allen Screw 2/-6 4 M6 x 20mm, Delta Tone/Seal 00ID7899 YES M8 x 25mm, Delta Tone/Seal 00ID7900 YES M0 x 25mm, Delta Tone/Seal 00ID790 YES 0 Shaft Pin 2/-36 ø5 x 26mm 3092 YES 0a Coupling Half 2/-6 2 NEMA, 56C, /3-2HP. ø5.8 / ø YES 2/-8 NEMA, 43/5TC, /3-3HP.ø /ø2 (Mach) YES NEMA, 82/84TC, 3-5HP. ø28.5/ø YES NEMA, 23TC, 7.5-0HP. ø34.9/ø YES 8(a) Priming/Vent Plug 2/-36 * G /2A, NV24 with NV9 x M8 stem No 9(a) Pipe Plug 2/-36 ** /4 NPT,SS SQHD, with Loctite No 2a Pipe Plug 2/-36 ** /4 NPT,SS SQHD, with Loctite No 23( c ) Plug 2/-36 ** G /2A, Solid No port, NV No 23a, e Plug (option) 2/-36 ** G /2A, w//4 port, NV No 23b, f Pipe Plug for Pos. 23a, 23e 2/-36 ** /4 NPT,SS SQHD, with Loctite No 23d Plug, Vented for Pos. 77a Cool Top option only 2/-36 2 G /2A, NV24, Vented No 25 Drain Plug 2/-36 /4 NPT,SS SQHD, with Loctite No 26 Staybolt 2/ 4 M2, ø0,7 x 79mm No 3 4 M2, ø0,7 x 06mm No 4 4 M2, ø0,7 x 33mm No 5 4 M2, ø0,7 x 60mm No 6 4 M2, ø0,7 x 87mm No 7 4 M2, ø0,7 x 24mm No 8 4 M2, ø0,7 x 24mm No 9 4 M2, ø0,7 x 268mm No 0 4 M2, ø0,7 x 295mm No 4 M2, ø0,7 x 322mm No 2 4 M2, ø0,7 x 349mm No 3 4 M2, ø0,7 x 376mm No 4 4 M2, ø0,7 x 403mm No 5 4 M2, ø0,7 x 430mm No 6 4 M2, ø0,7 x 457mm No 8 4 M2, ø0,7 x 5mm No 20 4 M2, ø0,7 x 565mm No 22 4 M2, ø0,7 x 69mm No 24 4 M2, ø0,7 x 673mm No 26 4 M2, ø0,7 x 727mm, 4 pole & 50 Hz No 29 4 M2, ø0,7 x 808mm, 4 pole & 50 Hz No 32 4 M2, ø0,7 x 889mm, 4 pole & 50 Hz No 36 4 M2, ø0,7 x 997mm, 4 pole & 50 Hz No Staybolt (Cool Top, Back-to-Back & Tandem Seal 2/ 4 M2, ø0,7 x 87mm No option) 3 4 M2, ø0,7 x 24mm No 4 4 M2, ø0,7 x 24mm No 5 4 M2, ø0,7 x 268mm No 6 4 M2, ø0,7 x 295mm No 7 4 M2, ø0,7 x 322mm No 8 4 M2, ø0,7 x 349mm No 9 4 M2, ø0,7 x 376mm No 0 4 M2, ø0,7 x 403mm No 4 M2, ø0,7 x 430mm No 2 4 M2, ø0,7 x 457mm No 3 4 M2, ø0,7 x 484mm No 4 4 M2, ø0,7 x 5mm No 5 4 M2, ø0,7 x 538mm No 6 4 M2, ø0,7 x 565mm No 8 4 M2, ø0,7 x 69mm No Included in kits? Due to part changes over time, all position numbers (-203) may not be used. This column indicates which model uses the spare part. If blank, the part is used in all models. B.O.M. Ref. Number is only available if it is not included in a kit or does not have a material number listed. If it is included in a kit (YES), or has a material number, request one of these numbers. If not included in a kit (No), but has a Material Number, use Material Number. 2

4 Parts List & Kits CR5-H Pos. Part Description Model Stages Used Comments/Dimensions B.O.M. Ref. Material parts list 26 Staybolt (Cool Top, Back-to-Back & Tandem) 20 4 M2, ø0,7 x 673mm No Seal Option) (Continued) 22 4 M2, ø0,7 x 727mm No 24 4 M2, ø0,7 x 78mm No 26 4 M2, ø0,7 x 835mm, 4 pole & 50 Hz No 29 4 M2, ø0,7 x 96mm, 4 pole & 50 Hz No 32 4 M2, ø0,7 x 997mm, 4 pole & 50 Hz No 36 4 M2, ø0,7 x 05mm, 4 pole & 50 Hz No 28 Motor Bolt 2/-6 4 NEMA, 56C, /3-2HP. UNC 3/8 x 25mm 00ID839 No NEMA, 82/84TC, 3-5HP.UNC/2 x 25mm 00ID840 No NEMA, 23TC, 7.5-0HP. UNC /2 x No 28g Bolt for foot Pos. 56a 2/-36 2 M2 x.75 x 20mm, Delta Tone/Seal No 36 Staybolt Nut 2/ mm x M2, Delta Tone/Seal 00ID797 No 37 Sleeve O-ring 2/-36 uu EPDM, ø37.5 x 3.3mm YES 2/-36 uu FKM, ø37.5 x 3.3mm YES 37b Sleeve O-ring (option) 2/-36 uu FXM, ø37.5 x 3.3mm YES 2/-36 uu FFKM, ø36.2 x 3.53mm YES 45 Neck Ring 2/-36 # stgs ø50.45 x ø35 x.7mm, PTFE YES 47a Bearing Ring/Spacer 2/-36 ^^^^ SiC 50, ø7.37 x ø3.0 x ø0.9 x 3mm YES Brg. Ring/Spacer (option for Graflon / Brz. 4a) 2/-36 ^^^^ TC, ø5.92 x ø3.0 x ø0.9 x mm 402 YES 49 Impeller 2/-36 # stgs ø73.0 x ø35.0 x 3.2mm (back-plate.0mm) No 2/-36 # stgs has a qty of No 49i Impeller (Low NPSH option) 2/-36 ø98.0 x ø52.8 x 7.3mm (back-plate.0mm) No 50a Top Guide Vane No Top Guide Vane Plate (option for destaging) 2/ No 5 Shaft, Complete 2/ ø2 x 60.5mm No 3 ø2 x 80.5mm No 4 ø2 x 24.5mm No 5 ø2 x 234.5mm No 6 ø2 x 268.5mm No 7 ø2 x 288.5mm No 8 ø2 x 322.5mm No 9 ø2 x 342.5mm No 0 ø2 x 376.5mm No ø2 x 396.5mm No 2 ø2 x 430.5mm No 3 ø2 x 450.5mm No 4 ø2 x 484.5mm No 5 ø2 x 504.5mm No 6 ø2 x 538.5mm No 8 ø2 x 592.5mm No 20 ø2 x 646.5mm No 22 ø2 x 700.5mm No 24 ø2 x 754.5mm No 26 ø2 x 80.5mm, 4 pole & 50 Hz No 29 ø2 x 882.5mm, 4 pole & 50 Hz No 32 ø2 x 963.5mm, 4 pole & 50 Hz No 36 ø2 x 07.5mm, 4 pole & 50 Hz No Shaft, Cpl. (Cool Top,Back-to-Back&Tandem Seal 2/ ø2 x 265.5mm No option) 3 ø2 x 285.5mm No 4 ø2 x 39.5mm No 5 ø2 x 339.5mm No 6 ø2 x 373.5mm No 7 ø2 x 393.5mm No 8 ø2 x 427.5mm No 9 ø2 x 447.5mm No 0 ø2 x 48.5mm No ø2 x 50.5mm No 2 ø2 x 535.5mm No 3 ø2 x 555.5mm No 4 ø2 x 589.5mm No 5 ø2 x 609.5mm No 6 ø2 x 643.5mm No 8 ø2 x 697.5mm No 20 ø2 x 75.5mm No 22 ø2 x 805.5mm No 24 ø2 x 859.5mm No 26 ø2 x 906.5mm, 4 pole & 50 Hz No 29 ø2 x 987.5mm, 4 pole & 50 Hz No 32 ø2 x 068.5mm, 4 pole & 50 Hz No 36 ø2 x 76.5mm, 4 pole & 50 Hz No Included in kits? Due to part changes over time, all position numbers (-203) may not be used. This column indicates which model uses the spare part. If blank, the part is used in all models. B.O.M. Ref. Number is only available if it is not included in a kit or does not have a material number listed. If it is included in a kit (YES), or has a material number, request one of these numbers. If not included in a kit (No), but has a Material Number, use Material Number. 3

5 Parts List & Kits CR5-H Pos. parts list Part Description Model Stages Used Comments/Dimensions B.O.M. Ref. Material Included in kits? 55 Outer Sleeve 2/ ø38 x 44.6mm No 3 ø38 x 7.6mm No 4 ø38 x 98.6mm No 5 ø38 x 25.6mm No 6 ø38 x 52.6mm No 7 ø38 x 79.6mm No 8 ø38 x 206.6mm No 9 ø38 x 233.6mm No 0 ø38 x 260.6mm No ø38 x 287.6mm No 2 ø38 x 34.6mm No 3 ø38 x 34.6mm No 4 ø38 x 368.6mm No 5 ø38 x 395.6mm No 6 ø38 x 422.6mm No 8 ø38 x 476.6mm No 20 ø38 x 530.6mm No 22 ø38 x 584.6mm No 24 ø38 x 638.6mm No 26 ø38 x 692.6mm, 4 pole & 50 Hz No 29 ø38 x 773.6mm, 4 pole & 50 Hz No 32 ø38 x 854.6mm, 4 pole & 50 Hz No 36 ø38 x 962.6mm, 4 pole & 50 Hz No 56a Foot for Pos. 6 2/-36 H=43mm, W=96mm, ø6mm hole CL 52mm, CI No 56f Bolt for base Pos C/82TC 2/-6 2 Hex Hd./2-3 UNC x SAE 5, Zinc plated YES 23TC Hex Head /2-3 UNC x.25 SAE 5, Zinc plated YES 56g Washer for bolt Pos. 56f 2/-36 2 /2 SAE, Zinc plated YES 60 Stack Compression Spring 2-36 ø36 x 3.5mm No 64 Spacing Pipe 2/-36 ^^^ ø5.85 x ø2.85 x 26.03mm No 64a Spacing Pipe 2/-36 ^^^^ ø5.85 x ø2.85 x 3.0mm YES Spacing Pipe (option for Graflon / Brz. 4a) 2/-36 ^^^^ Use with TC Pos. 47a, ø5 x ø2.7 x 5.0mm 4042 YES 64c Clamp, Splined 2/-36 ø5 x ø3.0 x ø0.9 x 3mm YES 64d Spacing Pipe 2/-36 ^^^^^ ø5 x ø3.0 x ø0.9 x 4.5mm No 64e Spacing Pipe (Low NPSH option only) 2/-36 2 ø5 x ø3.0 x ø0.9 x 0.0mm No 64f Spacing Pipe (Low NPSH option only) 2/-36 ø5 x ø3.0 x ø0.9 x 7.3mm No 64g Spacing Pipe (de-staging option only) 2/-36 ø5 x ø3.0 x ø0.9 x 27.0mm No 65 Neck Ring Retainer 2/-36 # stgs ø43.5 x ø34.0 x 3.6mm YES 66 Lock Washer Set for Shaft 2/-36 ø3.5 x ø8.2 x 2.6mm YES 66a Washer for Staybolt 2/-36 4 DIN 25A, ø24 x ø3 x 2.5mm, Delta Tone/Seal No 67 Lock Nut for Shaft 2/-36 3mm x M8 00ID206 YES 69 Spacing Pipe 2/-36 y ø5.85 x 2.85 x 2.0mm No 69a Spacing Pipe (de-staging option only) 2/ ø5.85 x 2.85 x 8.0mm No 76 Nameplate 2/ SS, 60 x 45mm No 76a Rivet for Nameplate 2/ SS, ø3 x 5mm No 77a Pump Head Cover for Back-to-Back, Tandem Seal 2/-36 Cast Stainless No 77a Pump Head Cover for Cool Top (option) 2/-36 Cast Stainless No 79 Disc / Plate for Cool Top 2/-36 Stainless No 90 Main Support Baseplate 56C/82TC 2/ YES 23TC 8 BP.Cpl.48, L=29mm x W=38mm x H=07.9mm YES Main Support Baseplate - Longer versions 82TC -6 XLBP (39), L=500mm x W=305mm x H=06.5mm YES 23TC XLBP2(48), L=777.8mm x W=38mm x H=07.9mm YES 90a Bolt for motor to slider Pos. 90b 56C 2/-6 4 Hex Head 5/6-8 UNC x.75 SAE 5, Zinc plated YES 82TC Hex Head 3/8-6 UNC x.5 SAE 5, Zinc plated YES 23TC Hex Head 3/8-6 UNC x 5/8 SAE 5, Zinc plated YES 90b Motor support /slide rail 56C 2/-6 2 GA, BP39, L=204mm x H=45.5mm x W=25.4mm YES 82TC GA, BP39, L=230mm x H=23.0mm x W=25.4mm YES 23TC GA, BP48, L=252mm x H=20mm x W=25.4mm YES 90c Support Bracket for Pump Cartridge 2/ SS, H=74mm CL of hole, GA No 90d Bolt for motor slide rail Pos. 90b to base Pos C 2/-6 4 Hex Head /4-20 UNC x SAE 5, Zinc plated YES 82/23TC Hex Head /4-20 UNC x.75 SAE 5, Zinc plated YES 90f Washer for motor bolt Pos. 90a to slide rail Pos. 90b 56C 2/-6 4 5/6 SAE, Zinc plated YES 82/23TC /8 SAE, Zinc plated YES 00 Priming/Vent Plug O-ring 2/-36 EPDM, ø6.3 x 2.4mm 00ID288 YES 2/-36 FKM, ø6.3 x 2.4mm 00ID223 YES 00(a) Priming/Vent Plug O-ring (option) 2/-36 FFKM, ø6.3 x 2.4mm YES 2/-36 FXM, ø6.3 x 2.4mm YES 02 O-ring for Pos. 05b Back-to-Back 2/-36 EPDM, ø8 x 2.5mm 00ID204 YES 2/-36 FKM, ø7.86 x 2.62mm 00ID287 YES Due to part changes over time, all position numbers (-203) may not be used. This column indicates which model uses the spare part. If blank, the part is used in all models. B.O.M. Ref. Number is only available if it is not included in a kit or does not have a material number listed. If it is included in a kit (YES), or has a material number, request one of these numbers. If not included in a kit (No), but has a Material Number, use Material Number. 4

6 Parts List & Kits CR5-H Pos. parts list Part Description Model Stages Used Comments/Dimensions B.O.M. Ref. Material Included in kits? 02 O-ring for Pos. 05b Back-to-Back (option) 2/-36 FFKM, ø7.86 x 2.62mm YES 2/-36 FXM, ø7.86 x 2.62mm No 03 Stationary Seal Ring for 05b Back-to-Back 2/-36 TC, 2mm YES Stationary Seal Ring for 05b Back-to-Back (option) 2/-36 SiC,2mm YES 04 Rotating Seal Ring for 05b Back-to-Back 2/-36 TC, 2mm YES Rotating Seal Ring for 05b Back-to-Back (option) 2/-36 SiC, 2mm YES 05(b) Shaft Seal HQBE 2/-36 *** SiC, Carbon with resin-impregnated, EPDM YES Shaft Seal HQBV 2/-36 *** SiC, Carbon with resin-impregnated, FKM YES Shaft Seal HQBK (option) 2/-36 *** SiC, Carbon with resin-impregnated, FFKM YES Shaft Seal HQQE 2/-36 *** SiC, SiC, EPDM YES Shaft Seal HQQV 2/-36 *** SiC, SiC, FKM YES Shaft Seal HQQF (option) 2/-36 *** SiC, SiC, FXM YES Shaft Seal HQQK (option) 2/-36 *** SiC, SiC, FFKM YES Shaft Seal HUBE 2/-36 *** TC, Carbon with resin-impregnated, EPDM YES Shaft Seal HUBV 2/-36 *** TC, Carbon with resin-impregnated, FKM YES Shaft Seal HUBF (option) 2/-36 *** TC, Carbon with resin-impregnated, FXM YES Shaft Seal HUBK (option) 2/-36 *** TC, Carbon with resin-impregnated, FFKM YES Shaft Seal HUUE 2/-36 *** TC, TC, EPDM YES Shaft Seal HUUV 2/-36 *** TC, TC, FKM YES Shaft Seal HUUF (option) 2/-36 *** TC, TC, FXM YES Shaft Seal HUUK (option) 2/-36 *** TC, TC, FFKM YES 05b Shaft Seal/inboard for Back-to-Back OQQE 2/-36 SiC, SiC, EPDM YES Shaft Seal/inboard for Back-to-Back OQQV 2/-36 SiC, SiC, FKM YES Shaft Seal/inboard for Back-to-Back OUUE 2/-36 TC, TC, EPDM YES Shaft Seal/inboard for Back-to-Back OUUV 2/-36 TC, TC, FKM YES 07 O-ring for Pos. 05b Back-to-Back 2/-36 EPDM, ø.5 x 4.3mm 00ID2040 YES 2/-36 FKM, ø.5 x 4.3mm 00ID286 YES O-ring for Pos. 05b Back-to-Back (option) 2/-36 FFKM, ø.5 x 4.3mm YES 2/-36 FXM, ø.5 x 3.8mm No 08 Spring for Pos. 05b Back-to-Back 2/-36 2mm YES 09(a) O-ring for Shaft Seal Pos. 05 2/-36 EPDM, ø2.3 x 3.0mm 00ID798 YES 2/-36 FKM, ø2.2 x 3.0mm 00ID2339 YES 09b O-ring for Shaft Seal Pos. 05 (option) 2/-36 FFKM, ø23.47 x 2.62mm YES 2/-36 FXM, ø22 x 2.75mm YES Seal Driver (small) for Pos. 05b Back-to-Back 2/ YES 2 Seal Driver (large) for Pos. 05b Back-to-Back 2/ YES 2a Seal Drv threaded for 2, Pos. 05b Back-to-Back 2/ YES 3 Set Screw for 2a, for Pos. 05b Back-to-Back 2/-36 3mm x M5 x 6mm 00ID7392 YES 7 Air Vent Pipe for 8 2/-36 G/2, 36SS, 60 x 43mm YES 7a Counter Nut for Pipe 7 2/-36 NV24, internal G/2, 36SS YES 8 Air Vent 2/-36 Air vent type 5-AV - 5/ YES 46 Allen Bolt for 47/48, for Pos. 05b Back-to-Back 2/ mm x M3 x 5mm YES 47 Stationary Seal Retainer - Pos. 05b Back-to-Back 2/-36 NV36, 36SS YES 48 Seal Retainer Washer - Pos. 05b Back-to-Back 2/-36 36SS, ø36.0 x ø26.0 x ø23.0 x ø2.6 x 5.0mm YES 49 Connecting Pipe Complete for Cool Top 2/-36 NV36, 36SS, FXM & EPDM YES 2/-36 NV36, 36SS, FXM & FKM YES 49a Retainer for bushing 2/-36 36SS, ø22.0 x ø7.0 x 9mm YES 49b Bushing 2/-36 Graflon, ø2..2 x ø2.4 x 53mm YES 49c Connecting Pipe less 09a&b and 49a&b 2/-36 NV36, 36SS YES 20 Flange, Suction 2/ #, 4 x /2-3 UNC threaded flange, e-coat No 2/ #, 4 x 3/4-0 UNC threaded flange, e-coat No 20a Flange, Discharge 2/-5 50#, 4 x /2-3 UNC threaded flange, e-coat No 2/ #, 4 x 5/8 - UNC threaded flange, e-coat No 203 Retaining ring for 20,.5 flange 2/-36 Stainless, ø72.6 x No 203a Retaining ring for 20a,.0 flange 2/-36 Stainless, ø53.6 x No Due to part changes over time, all position numbers (-203) may not be used. This column indicates which model uses the spare part. If blank, the part is used in all models. B.O.M. Ref. Number is only available if it is not included in a kit or does not have a material number listed. If it is included in a kit (YES), or has a material number, request one of these numbers. If not included in a kit (No), but has a Material Number, use Material Number. 5

7 Parts List & Kits CR5-H Notes: The first number is total number of impellers. An exceptions to this format is the CR5-H and Low NPSH models. Examples: a CR5-H is actually a CR5-2/H, it has 2 chambers and impeller (de-staged by ) - it uses a 2 stage shaft. Example: a Low NPSH CR5-3H is actually a CR5-3/2H, it has 3 chambers and 2 impellers (de-staged by ) - it uses a 3 stage shaft. ^^^ 2 to7 stage = # of Stages less 2 8 to 2 stage = # of stages less 3 3 to 6 stage = # of stages less 4 8 to 22 stage = # of stages less 5 24 to 26 stage = # of stages less 6 29 to 32 stage = # of stages less 7 36 stage = # of stages less 8 Exceptions to the above: Low NPSH model less additional. When de-staging by 2 impellers, replace top chamber Pos. 4 with Pos. 5a ^^^^ 2 to 7 stage = use 8 to 2 stage = use2 3 to 6 stage = use 3 8 to 22 stage = use 4 24 to 26 stage = use 5 29 to 32 stage = use 6 36 stage = use 7 Keys to Symbols: KITS Ø ANSI CPL EPDM FFKM FKM FXM M mm MG N NBR NEMA PTFE SiC TC UNC... Recommended spare part... Diameter... American National Standards Institute... Complete Assembly these parts consist of more than one component... Ethylene Propylene (also known as EPR and EPT) an elastic substance similar to rubber... Kalrez Elastomer made by DuPont... Fluoro Elastomer (generic for Viton)... Fluoraz Elastomer made by Greene Tweed... International standard thread size designation (thread diameter in mm)... Millimeter... Identifies Grundfos motor type/size... Stainless... Buna - N (also known as Nitrile) an elastic substance similar to rubber... National Electrical Manufacturers Association... Teflon... Silicon Carbide... Tungsten Carbide... Unified National Coarse a standard for threads on bolts ^^^^^ used only in pumps with the following amount of stages 2, 4, 6, 8, 0, 2, 4, 6, 20, 22, &24. * Standard use. Back-to-Back or Tandem pump version use 3 ** Standard use. Back-to-Back or Tandem pump version use 3 *** used in Hxxx (Standard), 2 used in Pxxx (Tandem) pump version y Standard use. CR(I,N)5-2/ replace with Pos. 69a # stgs Use the number of stages in standard models, less one in de-staged and Low NPSH models. uu Standard use 2. Back-to-Back or Tandem pump version use 3 Standard use 2. Back-to-Back or Tandem pump version use 6 * Standard use. When de-staging pump by 2 impellers, replace top chamber Pos. 4 with an additional Pos. 5a 6

8 Spare Part Kits CR5-H Spare Part Kits Since certain pump parts can be expected to exhibit wear at the same time as related pump parts, they have been grouped into the following kits for your convenience. The numbers indicate the quantity of the part within each kit. Please order these kits using the kit material number at the top of the columns. CR(I, N)5 SiC Bearing WEAR PARTS KIT 2-7 Kit WEAR PARTS KIT 8-2 Kit WEAR PARTS KIT 3-6 Kit WEAR PARTS KIT 7-22 Kit WEAR PARTS KIT Kit WEAR PARTS KIT Kit a Chamber N Cpl. w/pos.45 & 65 & SiC Bearing Gasket for Oval Flange, 95 x 55 x ø35 x 2mm Neck Ring, ø50.45 x ø35 x.7mm, PTFE a Bearing Ring/Spacer, SiC 50, 3mm a Spacing Pipe, ø5.85 x ø2.85 x 3.0mm c Clamp, Splined, ø5 x ø3.0 x ø0.9 x 3mm Neck Ring Retainer, N, ø52.5 x ø36.7 x 5.3mm Lock Washer Set of 2, ø3.5 x ø8.2 x 2.6mm Lock Nut, 3mm x M8 00ID206 CR(I, N )5 Graflon Bearing WEAR PARTS KIT 2-7 Kit WEAR PARTS KIT 8-2 Kit WEAR PARTS KIT 3-6 Kit WEAR PARTS KIT 7-22 Kit WEAR PARTS KIT Kit WEAR PARTS KIT Kit a Chamber N Cpl. w/pos.45 & 65 & Graflon Brg Gasket for Oval Flange, 95 x 55 x ø35 x 2mm Neck Ring, ø50.45 x ø35 x.7mm, PTFE a Bearing Ring/Spacer, TC,.0mm a Spacing Pipe, ø5.85 x ø2.85 x 5.0mm c Clamp, Splined, ø5 x ø3.0 x ø0.9 x 3mm Neck Ring Retainer, N, ø52.5 x ø36.7 x 5.3mm Lock Washer Set of 2, ø3.5 x ø8.2 x 2.6mm Lock Nut, 3mm x M8 00ID206 STACK KITS Model Material CR(I) CR(I) CR(I) CR(I) CR(I) CR(I) CR(I) CR(I) CR(I) CR(I) CR(I) CR(I) CR(I) CR(I) CR(I) CR(I) CR(I) CR(I) CR(I) *** CR(I) *** CR(I) *** CR(I) *** CR(I) ***For 4 pole & 50 Hz operation only. CR(I )5 Bronze Bearing WEAR PARTS KIT 2-7 Kit WEAR PARTS KIT 8-2 Kit WEAR PARTS KIT 3-6 Kit WEAR PARTS KIT 7-22 Kit WEAR PARTS KIT Kit WEAR PARTS KIT Kit a Chamber N Cpl. w/pos.45 & 65 & Bronze Brg Gasket for Oval Flange, 95 x 55 x ø35 x 2mm Neck Ring, ø50.45 x ø35 x.7mm, PTFE a Bearing Ring/Spacer, TC,.0mm a Spacing Pipe, ø5.85 x ø2.85 x 5.0mm c Clamp, Splined, ø5 x ø3.0 x ø0.9 x 3mm Neck Ring Retainer, N, ø52.5 x ø36.7 x 5.3mm Lock Washer Set of 2, ø3.5 x ø8.2 x 2.6mm Lock Nut, 3mm x M8 00ID206 STANDARD SHAFT SEAL KIT, BALANCED CARTRIDGE Kit (Maximum allowed working PSI is 435) Kit (Tandem Seal option Pumps require 2 of each Seal Kit) Kit Kit Kit Kit Kit HQBE HQBK HQBV HQQE HQQF HQQK HQQV N/A Grinding Device Tool for Emery Cloth 3707 N/A Emery Cloth

9 Spare Part Kits CR5-H Spare Part Kits (continued) OPTIONAL SHAFT SEAL KIT, BALANCED CARTRIDGE Kit (Maximum allowed working PSI is 435) Kit (Tandem Seal option Pumps require 2 of each Seal Kit) Kit Kit Kit Kit Kit Kit Pos. Description Material Qty. Included in each Kit 05 HUBE HUBF HUBK HUBV HUUE HUUF HUUK HUUV N/A Grinding Device Tool for Emery Cloth 3707 N/A Emery Cloth INBOARD SHAFT SEAL & Gasket KIT, Back to Back OQQE Kit INBOARD SHAFT SEAL & Gasket KIT, Back to Back OQQV Kit INBOARD SHAFT SEAL & Gasket KIT, Back to Back OQQV Kit INBOARD SHAFT SEAL & Gasket KIT, Back to Back OQQK Kit INBOARD SHAFT SEAL & Gasket KIT, Back to Back OUUE/V Kit (An HQQx or HUUx seal kit must also be used for respectively to complete seal repairs) 37 Sleeve O-ring, EPDM, ø37.5 x 3.3mm Sleeve O-ring, FKM, ø37.5 x 3.3mm , 00(a) Drain Plug O-ring, EPDM, Ø6.3 x 2.4mm 00ID288 7 Drain Plug O-ring, FKM, Ø6.3 x 2.4mm 00ID O-ring, EPDM, ø8 x 2.5mm 00ID204 O-ring, FKM, ø7.86 x 2.62mm 00ID287 O-ring, FFKM, ø7.86 x 2.62mm Stationary Seal Ring, SiC,2mm Stationary Seal Ring, TC,2mm Rotating Seal Ring, SiC, 2mm Rotating Seal Ring, TC, 2mm O-ring, EPDM, ø.5 x 4.3mm 00ID2040 O-ring, FKM, ø.5 x 4.3mm 00ID286 O-ring, FFKM, ø.5 x 4.3mm Spring, 2mm a O-ring, EPDM, ø2.3 x 3.0mm 00ID798 O-ring, FKM, ø2.2 x 3.0mm 00ID2339 O-ring, FFKM, ø23.47 x 2.62mm Driver for pos Driver for pos a Driver for pos Set Screw for pos.2a 00ID Allen Bolt for pos.47 & 48, 2.5mm x M3 x 5mm Stationary Seal Retainer - NV36, 36SS Seal Retainer Washer -36SS, ø36.0 x ø2.6 x 5.0mm N/A Grinding Device Tool for Emery Cloth 3707 N/A Emery Cloth GASKET KIT (EPDM) Kit GASKET KIT (FKM) Kit GASKET KIT (FXM) Kit GASKET KIT (FFKM) Kit GASKET KIT (EPDM)-Double Seal option. Kit GASKET KIT (FKM)-Double Seal option. Kit GASKET KIT (FFKM)-Double Seal option. Kit GASKET KIT (FXM, & EPDM)- Cool-Top option Kit Pos. Description Material Qty. Included in each Kit 37 Sleeve O-ring, EPDM, ø37.5 x 3.3mm Sleeve O-ring, FKM, ø37.5 x 3.3mm b Sleeve O-ring, FXM, ø37.5 x 3.3mm Sleeve O-ring, FFKM, ø36.2 x 3.53mm , 00(a) Drain Plug O-ring, EPDM, Ø6.3 x 2.4mm 00ID Drain Plug O-ring, FKM, Ø6.3 x 2.4mm 00ID , 00a Drain Plug O-ring, FXM, ø6.3 x 2.4mm Drain Plug O-ring, FFKM, ø6.3 x 2.4mm (a) O-ring for Pos.05(b) &49, EPDM, Ø2.3 x 3.0mm 00ID798 O-ring for Pos.05(b) &49, FKM, Ø2.2 x 3.0mm 00ID b O-ring for Pos.05(b) &49, FXM, Ø22.0 x 2.75mm O-ring for Pos.05(b) &49, FFKM, Ø23.47 x 2.62mm NEMA COUPLING KIT ø5.8/ø2 Kit 4534 ø22.225/ø2 Kit ø28.5/ø2 Kit 4535 ø34.9/ø2 Kit Allen Screw, M6 x 20mm, Delta Seal 00ID Allen Screw, M8 x 25mm, Delta Seal 00ID Allen Screw, M0 x 25mm, Delta Seal 00ID790 0 Shaft Pin, ø5 x 26mm, Stainless a Coupling Half, 56C, /3-2HP. ø5.8 / ø Coupling Half, 43/5TC, /3-3HP. Ø / ø Coupling Half, 82/84TC, 3-5HP. ø28.5/ø Coupling Half, 23TC, 7.5-0HP. ø34.9/ø

10 Spare Part Kits Accessories CR5-H Spare Part Kits (continued) COUPLING GUARD KIT NEMA 56C, /3-2HP Kit NEMA 82-25TC, 3-0HP Kit Coupling Guard, W=27mm x H=90.5mm Coupling Guard, W=57mm x H=7mm a Screw comb.slot torx/straight slot 4 x 8mm Air Vent Kit - Horizontal Units CR-H, CRN-HS to 20 Kit Pos. Description Material 7 Air Vent Pipe, short for 8, G/2, 60x a Counter Nut for Pipe 7, G/ Air vent type 5-AV - 5/ Qty. Included in each Kit 2 Connecting Pipe for Cool Top (EPDM, FKM & FXM) Kit a O-ring for Pos.05(b) &49, EPDM, Ø2.3 x 3.0mm 00ID798 O-ring for Pos.05(b) &49, FKM, Ø2.2 x 3.0mm 00ID b O-ring for Pos.05(b) &49, FXM, Ø22.0 x 2.75mm a Retainer for bushing, 36SS, ø22.0 x ø7.0 x 9mm b Bushing, Graflon, ø2..2 x ø2.4 x 53mm c Connecting pipe, NV36, 36SS Accessories ANSI COMPANION FLANGES FOR CR-H, CRN-HS to 20 -/2" and " Threaded CI Black for GA 25 Lb. Class Kit N/A Hex Head Cap Screw/Bolt /2"-3X 2" UNC ZP N/A Flange ANSI #50.5" NPT. Cast Iron - Black N/A Flange ANSI #50 " NPT. Cast Iron - Black N/A Gasket /2" Full Face 50 Lb. ANSI N/A Gasket " Full Face 50 Lb. ANSI ANSI COMPANION FLANGES FOR CR-H, CRN-HS to 20 -/2" and " Threaded CI Black for GA 250 Lb. Class Kit N/A Hex Head Cap Screw/Bolt 3/4"-0 X 2.5" UNC ZP N/A Hex Head Cap Screw/Bolt 5/8"- X 2.25" UNC ZP N/A Flange ANSI #300.5" NPT. Cast Iron - Black N/A Flange ANSI #300 "NPT. Cast Iron - Black N/A Gasket /2" Full Face 300 Lb. ANSI N/A Gasket " Full Face 300 Lb. ANSI ANSI COMPANION FLANGES FOR CR-H, CRN-HS to 20 -/2" and " Threaded Stainless, 50 Lb. Class Kit N/A Hex Head Cap Screw/Bolt /2"-3X 2" 36SS N/A Flange ANSI #50.5" NPT 36SS N/A Flange ANSI #50 " NPT 36SS N/A Gasket /2" Full Face 50 Lb. ANSI N/A Gasket " Full Face 50 Lb. ANSI ANSI COMPANION FLANGES FOR CR-H, CRN-HS to 20 -/2" and " Threaded Stainless, 300 Lb. Class Kit N/A Hex Head Cap Screw/Bolt 3/4"-0 X 2.5" 36SS N/A Hex Head Cap Screw/Bolt 5/8"- X 2.25" 36SS N/A Flange ANSI #300.5" NPT 36SS N/A Flange ANSI #300 "NPT 36SS N/A Gasket /2" Full Face 300 Lb. ANSI N/A Gasket " Full Face 300 Lb. ANSI

11 Spare Part Kits Accessories CR5-H Accessories (continued) Baseplate Kit 39 56C for GA Kit TC for GA Kit XLBP 56C for GA Kit TC for GA Kit Baseplate Cpl. 39, L=99* x W=305* x H=06.5* Baseplate Cpl. XLBP, L=500* x W=305* x H=06.5* N/A Slider & fastners for 56C(consists of slider & hardware) N/A Slider & fastner for 82TC (consists of slider & hardware) N/A Hardware Kit /68/78(cont. pos.56f, g, 90a,d& f)** N/A Hardware Kit (cont. pos.56f & g, 90a, d & f)** f Bolt, Hex Head /2-3 UNC x " SAE 5, Zinc plated N/A g Washer, /2" SAE, Zinc plated N/A a Bolt, Hex Head 5/6-8 UNC x.75" SAE 5, Zinc plated N/A 4 4 Bolt, Hex Head 3/8-6 UNC x.5" SAE 5, Zinc plated N/A b Slider, GA/B/C 56C/39BP, L=204* x H=45.5* x W=25.4* Slider, GA/B/C 82TC/39 BP, L=230* x H=23* x W=25.4* d Bolt, Hex Head /4-20 UNC x " SAE 5, Zinc plated N/A 4 4 Bolt, Hex Head /4-20 UNC x.75" SAE 5, Zinc plated N/A f Washer, 5/6" SAE, Zinc plated N/A 4 4 Washer, 3/8" SAE, Zinc plated N/A 4 4 * Values in mm, Length (L) is +/- 2mm, Height (H) is +/- mm, Width (W). ** Hardware kits and 8 are also available for sale. Baseplate Kit 48 23TC for GA Kit XLBP2 23TC for GA Kit Baseplate Cpl. 48, L=29* x W=38* x H=07.9* Baseplate Cpl. XLBP2, L=777.8* x W=38* x H=07.9* N/A Slider & fastners for 23TC(consists of slider & hardware) N/A Hardware Kit (consists of pos.56f, g, 90a,d& f)** f Bolt, Hex Head /2-3 UNC x.25" SAE 5, Zinc plated N/A g Washer, /2" SAE, Zinc plated N/A a Bolt, Hex Head 3/8-6 UNC x 5/8" SAE 5, Zinc plated N/A b Slider, GA/B/C 23TC/48BP, L=252* x H=20* x W=25.4* d Bolt, Hex Head /4-20 UNC x.75" SAE 5, Zinc plated N/A f Washer, 3/8" SAE, Zinc plated N/A 4 4 * Values in mm, Length (L) is +/- 2mm, Height (H) is +/- mm, Width (W). ** Hardware kits is also available for sale. 0

12 Spare Part Kits Special Tools CR5-H Special Tools Tools not generally available from normal sources. Mat. Description and Use 00SV SV SV SV204 Shaft Holder for Dismantling/Assembly Used to hold and protect the shaft during dismantling and assembly. Tubular Box Spanner for Shaft Seal 36. mm Used to install and remove the shaft seal. Fits a /2 drive ratchet. Puller for Neck Ring Used to remove the Neck Ring from Chamber. Circlip Pliers for Flange Lock Ring Used to remove the Lock Ring for the Flange. 00SV SV20 00SV200 Tool for Outer Sleeve Used to press sleeve into base. Bit Holder Used with Bits Kit, /4 Bits Kit NV 5 mm for M6, /4 NV 6 mm for M8, /4 NV 8 mm for M0, /4 (optional) 00SV202 Mat. 00SV SV SV SV SV022 Hexagon Socket Bit Used for Shaft Seal NV 2.5 mm for M5, /4 Standard Tools In addition to being available from Grundfos, comparable tools can be purchased through normal sources. Description and Use Wrenches Used to tighten various nuts. NV 0 mm for M6 NV 3 mm for M8 NV 7 mm for M0 NV 9 mm for M2 NV 24 mm for M6 Torque Wrench Used to torque various screws. 00SV Nm, 9 x 2 00SV Nm, 9 x 2 00SV Nm, 4x8 Torque Screwdriver Used to tighten various nuts. 00SV Nm, /4 Ratchet Spanner for all Adapters 00SV mm x 2 mm, /2 Socket Spanner with Inside Hex 00SV0296 NV 5 mm for M6, /2 x /2 00SV0297 NV 6 mm for M8, /2 x /2 00SV0298 NV 8 mm for M0, /2 x /2 00SV030 00SV SV SV027 00SV0524 Ring Spanner NV 0 mm for M6 NV 3 mm for M8 NV 7 mm for M0 NV 9 mm for M2 NV 24 mm for M6 Socket Spanner 00SV203 NV 3 mm for M8, 9 x 2

13

14 Being responsible is our foundation thinking ahead makes it possible Innovation is the essence Being responsible is our foundation Thinking ahead makes it possible Innovation is the essence L-CR-SM-059 8/2 PRINTED IN USA Subject to alterations. GrundFOs Pumps corporation 700 W. 8th Terrace Olathe, Kansas Phone: Fax: GrundFOs canada, Inc. 294 Brighton Road Oakville, Ontario L6H 6C9 Canada Phone: Fax: Bombas GrundFOs de Mexico s.a. de c.v. Boulevard TLC 5 Parque Industrial Stiva Aeropuerto Apodaca, N.L. Mexico Phone: Fax: