THE MACHINES CATALOGUE

Transcription

1 THE MACHINES CATALOGUE diateh.hr

2 Address: Hrastovička 33, Zagreb 10250, Croatia Tel/Fax: OIB: PDV ID/EORI: HR diateh@diateh.hr Bank account: ZB IBAN: HR SWIFT: ZABAHR2X CONTENTS 4 GASOLINE CUTTERS FLOOR 6 ELECTRIC CUTTERS FLOOR 8 SPECIAL CUTTERS FLOORS 9 TABLE CUTTERS 14 WALL CUTTERS 16 RADIAL CONCRETE CUTTER 17 AGGREGATES 18 CUTTERS WITH CABLE 19 HAND MACHINES JOINT CUTTER 20 HAND TOOLS - HAND GRINDER CONCRETE 21 HAND POLISHING MACHINES 22 HAND TOOLS - PNEUMATIC GRINDING 24 DRILLER STANDS 30 DRILLER 31 DRILLER PIPES 38 EQUIPMENT FOR DRILLER 40 ACCESSORIES 41 MULTI-DISC GRINDING MACHINES 42 SINGLE DISC GRINDING MACHINES 45 MACHINE FOR MILLING CONCRETE 46 CHAIN MACHINES diateh.hr All prices are individual and expressed without VAT Our Conditions of Sale and Delivery apply

3 GASOLINE CUTTERS / FLOOR FS450 BWT1 Gasoline floor cutter P 9,6 kw, Ø450 mm Gasoline floor cutter with removable water reservoir of 20 l cutting depths up to 172 mm Central supply of cooling water flange Finely adjustable lowering over the threaded shaft Automatic shutdown at the disappearance of oil Brake Diameter of disc: 450 mm Shaft width hole in the disc: of 25.4 mm 1 GB 12 mm, 57.4 mm TK Cutting depth: 172 mm : 9.6 kw (Honda) : 880 mm : 460 mm without the display section is recessed handles: 900 mm : 84 kg Saw blade diameter: 450 mm FS500 BSA The new floor saw with Honda-gasoline-engine GX390 (9,6 kw / 13 hp) is especially characterized by its swivel arm as well as highest-quality components. Designed for cutting concrete and asphalt. Ø 350/400/450/500 cutting depth up to 170mm Easily transportable, lightweight and manageable. Adjustable handlebar and metal guards. Gasoline or diesel engines available. Wheel regulated cutting depth. Double drive refrigeration through its tank or external supply. Two sides drive refrigeration. Optional electric start. Cutting blade mm: 350/400/450/500 mm: 25,4 Cutting depth mm: 95/120/145/170 Honda GX390 (9,6 kw / 13 hp) Water tank L: 30 mm: 1200 mm: 570 mm: , ,00 Aneto ,00 Easily transportable, lightweight and manageable. Adjustable handlebar and metal guards. Gasoline or diesel engines available. Wheel regulated cutting depth. Double drive refrigeration through its tank or external supply. Two sides drive refrigeration. Optional electric start. Aneto 350 Easily transportable, lightweight and manageable. Adjustable handlebar and metal guards. Gasoline or diesel engines available. Wheel regulated cutting depth. Double disk refrigeration through its tank or external supply. Two sides disk refrigeration Optional electric start ,00 Engine: HONDA Typ: PETROL Start up: MANUAL Engine power: (CV) 13 External disc Ø: 350 mm Internal disc Ø; 25,4 mm Cutting depth: 115 mm Water tank capacity: 20 L Machine size L x H x A mm: 1635x1100x585 Net weight: 92 kg Packaging size L x H x A (mm): 900x1050x700 Packaging weight: 110 kg Engine: HONDA Type: PETROL Start up: MANUAL Engine power (CV):13 External disc Ø: 450 mm Internal disc Ø: 25,4 mm Cutting depth: 165 mm Water tank capacity: 40 L Machine size L x H x A (mm): 1700 x 880 x 625 Net weight: 111 kg Packaging size L x H x A (mm): 900 x 1050 x 700 Packaging weight: 21 kg 2.080,00 4 * Optional electric start 5 Aneto 600 Metal guards. Gasoline or diesel engines available. Metal water tank. Wheel regulated cutting depth. Directionally stable by its design. Double disk refrigeration through its tank or external supply. Two sides disk refrigeration. Lifting hook incorporated. Engine: HONDA Type: PETROL Start up: Electric Engine power (CV): 20 External disc Ø: 600 mm Internal disc Ø : 25,4 mm Cutting depth: 225 mm Water tank capacity: 80 L Machine size L x H x A (mm): 1825 x 1070 x 681 Net weight: 180 kg Packaging size L x H x A (mm): 1200 x 1050 x 800 Packaging weight: 200 kg

4 ELECTRIC CUTTERS / FLOOR FS800EHH The compact electric cutter with 7.5 kw AC motor for cutting depth up to 315 mm FS450E The compact electric cutter with a 4 kw AC motor for cutting depth up to 172 mm Water supply central through flange Fine descent over the threaded shaft Drive drive over multispline strap Cutting and left and right side Diameter of disc: 450 mm Shaft width hole in the disc of 25.4 mm (1 ) 1 NL? 12 mm, 57.4 mm TK Additional holes for marginally cut. Cutting depth: 172 mm : 4.0 kw, 400 V : 830 mm : 650 mm : 770 mm : 95 kg Easy removing motor for transporting Shareable disk guard (cutting through the wall and over) Cutting to the left and right side Drive through the strap Hydraulic height adjustment Standard flange cut. against the wall Saw blade diameter: : 1 NL Ø 12, TK 57,4 Additional holes for fixation: Cutting depth: : : : : : 4.500, mm 25,4 (1 ) mm 6 x M6 TK 92 mm 315 mm 7,5 kw, 400 V 650 mm 600 mm 600 mm 118 kg 2.290,00 FS1000EVH FS 800 E Compact electric knife joints with the possibility of removing the engine and cutting on both sides 7.5 kw three-phase motor Cutting depth up to 315 mm Saw blade diameter: : Cutting depth: Engine: : : : : 3.400, mm 60 mm 340 mm 10 kw, 400 V mm 670 mm 840 mm 198 kg The powerful 15 kw electric cutter with electro-hydraulic feed and cutting depth up to 425 mm Electro hydraulic feed Foot pump in case of emergency shareable guard Cutting to the left and right side Drive through the strap Hydraulic height adjustment Standard flange cut. against the wall On demand is possible with blade diameter 1200 mm Saw blade diameter: : Additional holes for fixation Cutting depth: : : : : : 1000 mm 50 mm 6 x M8 TK 110 mm 425 mm 15 kw, 400 V 1150 mm 760 mm 1000 mm 360 kg ,00 6 7

5 SPECIAL CUTTERS / FLOORS TABLE CUTTERS FF200E Practical, easy transporting electro groover for easy processing of joints in concrete (pull the edges of the joints for puttying) Fine-tuning the cutting depth over the stars hand screw Easy assembly splines Diamond discs with a diameter of 180 mm can be used as a leading disk Isolating switch Dust extraction port 990,00 Chamfer grinder Diameter: : Slot width: : : : : : 130 mm 22,2 mm ca 2,8-8,0 mm 1,8 kw, 230 V 330 mm 330 mm mm 18 kg L55 Robust, powerful bench cutter for cutting ceramic, gress, porcelain, glass and insulation boards Up to 45 tilt cutting head Wheels for transportation removable Stable cutting head cutting blades up without dangerous strain Electric water pump Powder-coated parts Angle cutting guide for corner and 770,00 L120 Robust, powerful bench cutter with rotary cutting head for depth of cut up to 125 mm and the length of the cut over 1200 mm Up to 45 tilt cutting head Wheels for transportation removable Stable cutting head cutting blades up without dangerous strain Electric water pump Powder-coated parts Angle cutting guide for corner and straight cuts Adjustable cutting head to set up a stable depth of cut Cutting disc diameter of 200 mm 25.4 mm (1 ) Cutting depth 40 mm Cutting length 570 mm 1.5 kw, 230 V 1020 mm 480 mm 350 mm Transport height 800 mm 31 kg straight cuts Adjustable cutting head to set up a stable depth of cut Cutting disc diameter mm 25.4 mm (1 ) Cutting depth 125 mm Cutting length 1200 mm 2.2 kw, 230 V or 400 V 1700 mm 800 mm 1200 mm Transport height 550 mm 105 kg VFX 125 This miller was developed for cutting slots into screed floors to install floor heating pipes for a heating system Rigid design Compact and robust Exact adjustment of cutting depth Integrated dust extraction Swivel wheels for quick and exact manoeuvrability Minimum radius of slots approx. 60 mm Special diamond milling tool for dry cutting 230 V / 3 kw 400 V / 3 kw 4.390, ,00 3,0 kw / 230 V - Soft Start 3,0 kw / 400 V Saw blade Ø 125 mm Slot width 16 or 18 mm Max. cutting depth 0-25 mm 22,2 mm ± 60 kg L60 Robust, powerful bench cutter with rotary cutting head on springs for depth of cut up to 125 mm and a length of over 600 mm Up to 45 tilt cutting head Wheels for transportation removable Stable cutting head cutting blades up without dangerous strain Electric water pump Powder-coated parts Angle cutting guide for kutno- and straight cuts Adjustable cutting head to set up a stable depth of cut 1.560,00 Cutting disc diameter mm 25.4 mm (1 ) Cutting depth 125 mm Cutting length 600 mm 2.2 kw, 230 V or 400 V 1150 mm 800 mm 1200 mm Transport height 550 mm 90 kg 8 990,00 9

6 BS 230 Top Adjustable table slicer, easy to use, for the cutting wheel 230 Handy, light and user friendly table saw for cutting blade Guide rail on top Directly driven, roll mounted cutting head Extra stable frame and oversized Cutting table Cutting head with integrated tilting Hinged legs with transport rollers Powder-coated components TABLE CUTTERS Ø saw blade 230 mm 25,4 mm Cutting depth 50 mm Cutting depth 7001 / ,0 kw, 230 V 1180 mm 590 mm Transport height 1400 / kg Cutting depth 130 mm 2 diagonal cutting BS 350 Pro Adjustable table slicer, easy to use, for the cutting wheel 350, the length of the cut to 600 mm, a powerful electric motor of 1.35 kw, precision cutting up to 45 angle of inclination Ø saw blade Cutting depth 649, mm 25,4 mm 110 mm Cutting length 500 mm 2,2 kw, 230 V 1120 mm 670 mm / transport height 1300 / 700 mm 65 kg 660,00 BS 350 Pro L 790,00 BS 250 Pro Adjustable table slicer, easy to use, cutting length 1050mm, a powerful electric motor of 1.35 kw, precision cutting Guide rail on top With directly driven blade, roll mounted cutting head Extra strong frame and oversized cutting table Cutting head with integrated tilting function for accurate mitre cut Hinged legs with transport rollers Powder-coated components Ø saw blade 250 mm 25,4 mm Cutting depth 60 mm Cutting length 1050 / 9401 mm 1,35 kw, 230 V 1375 mm 740/6452 mm / transport height 1275 / 560 mm 73 kg 1 with preset cutting depth 2 width of transport 960,00 Powerful table saw for cutting blade diametar of disk 350 mm and cutting length up to 600 mm (BS 350 Pro-L) Cutting head tiltable up to 45 (BS 350 Pro-L) Cutting table running in Ball bearings Extra strong frame with hinged legs and transport rollers Powder coated components Removable water tray Ø saw blade Cutting depth Cutting length / Transport height 350 mm 25,4 mm 110 mm 600 mm 2,2 kw, 230 V 1220 mm 670 mm 1300 / 720 mm 73 kg BS 350 rugged, powerful table saw with tiltable and removable cutting head and compact dimensions for cutting depth up to 125 mm Cutting head tiltable up to 45 and removable for transport Transport rollers optional Handles for easy transport Cutting carriage protected against outlifting Cutting pilot for angle and straight cuts Electric water pump Powder coated components Wear resistant roller guides transport wheels Ø saw blade 350 mm 25,4 mm Cutting depth 110 mm Cutting length 500 mm 2,2 kw, 230 V 1120 mm 670 mm / transport height 1300 / 700 mm 65 kg 1.440,00 BS 400 Adjustable table slicer, easy-to-use, cutting depth up to 150 mm, precision cutting, variable head Up to 45 angle of inclination spring mounted cutting head for smooth cutting operations handles for easy transport cutting carriage protected against outlifting transport rollers optional cutting pilot for angle and straight cuts electric water pump powder coated components wear resistant roller guides adjustable cutting head TRANSPORT WHEELS Ø saw blade Cutting depth Cutting length Table size Heigth /transport height1 400 mm 25,4 (1 ) mm 150 mm 570 mm 400 x 450 mm 2,2 kw, 230 V 1250 mm 680 mm 450 / 800 mm 90 kg 1.320,

7 TABLE CUTTERS BS 750 Locking brake Master 800 / 1000 / 1200 Compact and easily manageable brick saw for saw blades Diametar of disk 750 mm and cutting depth up to 285 mm Rugged welded frame construction Extremly heavy duty hot-dip galvanised cutting table Powder coated components Cutting table with recirculating ball bearing guide and precision spindle Blade directly driven by special flat motor (IP55) Saw head lifting by gas-filled telescopic strut Electric water pump Big drain plug Lifting eyes for transport 4 transport rollers Ø saw blade 750 mm 40 (60) mm Max. cutting depth 285 mm Max. cutting length 900 mm Table size 610 x 650 mm 4,0 kw, 400 V 1800 mm 810 mm / transport height 1360 mm 195 kg 2.300,00 Rugged table saws with guide rail on top and cutting head Running in ball bearings for saw blade Ø 350 mm, Cutting depth up to 110 mm and cutting length From 800 mm to 1200 mm (respectively 980 mm to 1380 mm) Rigid aluminum guide rail on top with Cutting head running in ball bearings Extra strong steel frame design with Attachable cutting table extension Directly driven with isolation level IP55 Cutting head tiltable up to 45 Continuously adjustable and fixable Cutting depth Cutting length indicator and cutting pilot For angle cuts Integrated and extendable handles Hinged legs Powder-coated components BS900 Compact, easy to handle cutter blocks for use on site, cutting depth up to 292 mm The feed through the side winches Metal ears for loading / unloading machine Brake 4 Transport wheel Protecting water pump of sludge The possibility of electric discharge of pump Powder-coated parts Slide the cutting bridge Ø saw blade 900/1000 mm 60 mm Max. cutting depth 355/405 mm Max. cutting length 700 mm Table size 690 x 760 mm 7,5 kw, 400 V 2000 mm mm / transport height 1600 mm 305 kg 2 without lateral hand wheel 3.180,00 Master 800 Master 1000 Master BSB 900+ Robust and powerful cutter blocks for use on site, cutting depth up to 370 mm The feed through the side winches Metal ears for loading / unloading machine Brake 4 Transport wheel Protecting water pump of sludge The possibility of electric discharge of pump Powder-coated parts Slide the cutting bridge Ø saw blade 1000 mm 60 mm Max. cutting depth 405 mm Max. cutting length 700 mm Table size mm 690 x 760 mm Honda GX390 9,6 kw/13 hp 1930 mm 9201 mm / transport height 1620 mm 285 kg 4.200,00 Saw blade 350 mm 25,4 (1 ) mm Max. cutting depth 110 mm Max. cutting length 980 mm Diagonal cutting length mm Table size mm 953 x 521 mm Cutting table extension 400 x 305 mm 2,2 kw, 230 V Rotation spped 2800 min-1 Cutting head tiltable up to 45 / transport length 1500/ mm / transport width 780/660 3 mm / transport height 1550/690 3 mm 95 kg 1.400, mm 25,4 (1 ) mm 110 mm 1180 mm 760 mm 1103 x 521 mm 400 x 305 mm 2,2 kw, 230 V 2800 min / mm 780/660 3 mm 1550/690 3 mm 115 kg 350 mm 25,4 (1 ) mm 110 mm 1380 mm 960 mm 1303 x 521 mm 400 x 305 mm 2,2 kw, 230 V 2800 min / mm 780/660 3 mm 1550/690 3 mm 135 kg 1.500, ,00 1 lowering cutting head into material 2 cutting head 45 inclined, 10 mm overlap, 20 mm cutting depth / material 3 transporting dimensions with legs in hinged position and inserted handles 13

8 WALL CUTTERS WALL CUTTERS SW 800 Extremely reliable, fully hydraulic, with swivel arm, with automatic feed and engaging, self-adjusting guide, for cutting depths up to 710 mm disk up to 1600 mm Hydraulic feed and engaging with automatic optimizes the cutting speed to the conditions of cutting The minimum number of electrical components guarantee the highest reliability Hydraulic motor HD19 (for Ø 800-Ø1000 mm) series Two-speed hydraulic motor HD30 / 19 (for Ø mm optional) comes also with large cutting discs aggregate maximum power and maximum torque lossless Hydraulic motors for feed and engaging Self-adjustable guide blades are regularly adjust the guides unnecessary, allowing the simultaneous use of old and new rails 360 rotation of the swivel arm A system of quick couplings for all engines Development of special aluminum alloy high strength Cooling water through the central shaft and flange Design allows for easy service and maintenance Equipment for cutting along the edge of the wall (optional) Ø cutting blade Cutting depth Flush-cut holes Hydraulic power pack PowerBox sawing head motor 1600 mm 710 mm 60 mm 6 x M8 TK 110 mm HD19 (for Ø mm) HD31 (for Ø mm) HD30/19 (for Ø mm) A23-M (A23-RC) 22 kw, 240 bar, 0-55 l/min, 126 (140) kg 29,0 kg 5,0 kg The components / equipment SW800 Rails 1 m 590,00 Rails 1.5 m 890,00 Rail 2 m 1.190,00 Rails 2.5 m 1.490,00 The carrier rails 270,00 The stop rail 87,00 Shield disk GT800, closed, divisible 1.828,00 Shield disk BU800, cutting along the edge of the wall 594,00 Shield disk GT1200, closed, divisible 2.416,00 Shield disk BU1200, cutting along the edge of the wall 924,00 Shield disk G1600, closed 2.490,00 Shield disk BU1600 cutting along the edge of the wall 1.290,00 acceptance cutting along the edge of the wall (the inner flange, outer flanges tracks, equipment installation) 639,00 Hose with connections 10 m 68,00 Aggregate A23 M S650 HD17 Hydraulic cutter wall S650 / HD 17 Robust and proven a good system of double rail with electric fed, for the cutting depth Up to 440 mm disc diameter 650 mm to 1000 mm, remote control Short installation time with the system for quick installation Water cooling via a central shaft and flange Set S650 / HD17 consists of: 1x cutting head S650 / HD17 with a set of tools 1x hydro units A15-A23-R or R 1x Package hydraulic hose 10 m 1x Remote control 10 m 1x cable feed 10 m 1x Hose 10 m 1x rail 2,28 m 1.091,00 1x rails 1.38 m 771,00 4 carrier rails 270,00 1x shield drive GT800E, closed, divisible 754,00 1x shield drive BU 800, cutting the edge of the wall 252,00 1x shield drive GT1000, closed, divisible 855,00 1x shield drive BU 1000, cutting the edge of the wall 298,00 1x automatic engaging AS ,00 Saw blade diameter 650/1000 mm Cutting depth 265/440 mm 6 x M8 TK 90 mm Flush cut holesø 650 mm HD17 Hydraulic power pack A15-R 15 kw, 240 bar, 6 steps 9-36 l/min, 143 kg Hydraulic power pack DA16 16 kw, 340 bar, 0-55 l/min, 184 kg motor 4,6 kg saw head 33,5 kg Price with A15-R ,00 Price with A23-R ,00 Aggregate A23 R for wall cutters 14 15

9 RADIAL CONCRETE CUTTER AGGREGATES TL 1500 Powerful cutter for deep cutting for cutting depths of up to 1000 mm (with standard equipment) Short preparation thanks to rapid installation system Water supply centrally through the shaft and flange 1 saw head TL 1500 with track 1,4 m, hose set 3 m, tool set and hook wrench 1 hydraulic motor OMR200 1 drilling rig B 600 with track 1,2 m 1 drilling spindle B FS500/HG10/turn 1 spacer 100 mm 1 hose guide 1 blade guard carriage 1 blade guard GT 1000 mm, closed, divisible 1 closing cover 1 mitre master 1 intermediate piece with ball valve Saw blade diameter mm (1500) Cutting depth (with standard equipment) 1000 mm 35 mm (total) 172 kg Hydraulic power pack DA kw, 340 bar, 0-55 l/min, 217 kg (without hydraulic oil) ,00 A15-R / A15-E A15-R / A15-E Robust and multi-purpose hydraulic power pack for wall and wire-saws with stepless pressure adjustment up to max. 240 bar and variable flow rate from 22 to 42 l/min (adjustable in 6 steps) A15-R for drive of wall saws (S650) and other Meissner machines with electrical feeding/lowering function A15-E for drive of various drilling equipment and other machines without feeding option A15-R with integrated switch cabinet and remote control A15-E with ON/OFF-function oil flow rate in 6 steps adjustable (22-42 l/ min) designed for drive of wire saws and hydraulic drilling equipment big wheels for easy transportation weight (incl. oil) only 122 kg (A15-E) and 143 kg (A15-R) A15-R 7.940,00 A23-M / A23-RC New generation of hydraulic power packs with integrated automatic feeding control function for hydraulic motors, with water-cooled 22 kw electric motor, remote control (only A23-RC) and with remarkable low weight A23-M with integrated control panel A23-RC with remote control (cable 10 m) Abstraction of electrical components guarantees highest reliability Integrated hydraulic automatic control for feeding/lowering function Oil flow rate steplessly adjustable 0-55 l/min Optimal for drive of the wire saws and drilling systems Big wheels for easy transportation (incl. oil) only 126 kg (A23-M) and 140 kg (A23-RC) A23-R / A23-E New generation of hydraulic power packs with water-cooled 22 kw electric motor with remarkable low weight A23-R for drive of wall saws (S650) and other Meissner machines with electrical feeding/ lowering function A23-E for drive of various drilling equipment and other machines without feeding option A23-R with integrated switch cabinet and remote control A23-E with ON/OFF-function Oil flow rate in 6 steps adjustable (22-55 l/ Designed for drive of wire saws and hydraulic drilling equipment Big wheels for easy transportation (incl. oil) only 111 kg (A23-E) and 118 kg (A23-R) A23-R RD3500 Set consists of: 1 saw head TL 1500 with track 1,0 m, hose set 3 m, tool set and hook wrench 1 drilling rig B 800 with track 1,2 m 1 turning link RD FS500/HG10/turn 1 spacer 115 mm 1 hose guide 1 blade guard carriage 1 blade guard GT 1000 mm, closed, divisible 1 closing cover 1 intermediate piece with ball valve Saw blade diameter (1500) mm Cutting depth (with standard equipment) (690) mm 35 mm (total) 240 kg Hydraulic power pack DA kw, 340 bar, 0-55 l/min, 217 kg (without hydraulic oil) Components / Accessories The cutting head TL 1500 with a package of hose 3 m 4335,00 Rails 1 m 897,00 Rails 1.4 m 1158,00 HIDRAULIC MOTOR OMR ,00 Drill Stand B600 with rail 1.2m 3379,00 Drill Stand B800 with rail 1.2m 7650,00 The drill SPINDLE B ,00 FS500 / HG10 / hook wrenc 2150,00 Distance 100 mm 990,00 Distance 115 mm 990,00 Slider hood 1095,00 Protecting disk GT1000 mm, divisible, closed 914,00 Pivoting Coupling RD ,00 Anti strangulate sheet 52,00 Spindle LR 277,00 Connecting piece / kugel valve 360,00 Hydro-A23-R (without hose package) 13050,00 Hydro-A23-E (without hose package) 9500,00 Package hydraulic hose (for the A23-R/ A23-E) 896,00 Automatic engaging AS ,00 Set for cutting along the edge of the wall 887,00 A15-E 5.900,00 Set hydraulic hose price for 3 hose with valve 869,00 A23-M ,00 A23-RC , ,00 A23-E 9.590, ,

10 CUTTERS WITH CABLE HAND MACHINES JOINT CUTTER SWS83 Portable, rugged container diamond cutting cable to ca. 3 m (shortening of the cable into the machine ca. 6.3 m) Fitted with 2 plugs Pneumatic feed Voltage cables are kept constant spring Guide to the circular guidance 1-fold or 2-fold resilient Changing the angle of the output management Wheels to turn 2-fold bearing with grease gun Since the wheels are fastened on the one hand it is possible to mount the cable without interruption The required hydraulic drive above 11.5 kw (over 140 bar, l / min, is 21 to 26.5 m / s) 1 SWS 83 storage wire saw with linkage 1 foot plate with 2000 mm column 1 diagonal support 1 hydraulic motor 1 compressor (10 bar, 20 l tank) with control unit 1 pneumatic hoses set 10 m 2 flexible water supplies 2 protective covers 1650 mm 1 wire hand crank for drive wheel Max. wire storage Max. wire shortening Total travel (variabel) Depth of protective cover Ø drive wheel Ø deflector roll wire saw Without compressor 8,3 m 6,3 m 1400 mm 750 mm 700 mm 2100 mm 1650 mm 360 mm 200 mm 86 kg (dismountable in 3 parts; 26 kg, 28 kg and 32 kg) 10 bar, 20 l tank, 230 V, 33 kg Compressor Hydraulic power unit A 15-R 15 kw, 240 bar, 6 levels, 9-36 l/ min, 143 kg Hydraulic power unitda kw, 340 bar, 0-55 l/min, 184 kg HT45 Hydraulic pressing tool for connection of diamond wire up to a cross-section of 150 mm² Max. cross-section 150 mm² Max. Press capacity 50 kn Working pressure 600 bar 346 mm 2 kg PRICE without hydraulic power pack ,00 840,00 RSL 150 New RSL 150, the best for its ergonomics and performances. It is suitable for perforated brick, tiles, mainly masonries, concrete (reinforced concrete too) and for other compact materials Compact and well-balanced it assures a peerless manageability High 2300 W motor power Easy and quick setting and substitution of discs DRS HS 350 Lightweight and handy electric hand saw for wet and dry cutting applications and cutting depth up to 140 mm Water supply via flange Water supply control by flow indicator Saw carriage with spirit levels Insulation class I Standard with PRCD Steppless adjustable and fixable cutting depth 1.099,00 Ø diamond blade TSD 180 Bounces reduced in order to make cuttings in proximity of the border Trail depth regulating with graduated indicator Power supply Power rating Rotation speed Rotation speed under load Trail depth Trail width Suitable for blade up to 350 mm 25,4 (1 ) mm 2,1 kw, 230 V insulation class I PRCD Serie 400 mm 320 mm 240 mm 9,8 kg TSD 180 for trails execution up to 55mm depth It is suitable for perforated brick, tiles, mainly masonries, concrete (reinforced concrete too) and for other compact materials Lightweight and easy to handle thanks to the comfortable handgrip New safety switch easy to activate with the same finger V 2300 W 7500 min 4300 min 45 mm 46 mm The work will be dust free in association with the Rurmec aspiration system Power supply Power rating Rotation speed Rotation speed under load Trail depth Trail width Suitable for blade up to ,00 806,00 Ø 150 mm 5,8 kg V 1800 W 4100 min 3200 min 55 mm 45 mm Ø 180 mm 6 Kg

11 HAND TOOLS - HAND GRINDER CONCRETE HAND POLISHING MACHINES MR180 MR125 Strong and light angle grinder concrete strength 1200 x 3000 RPMs intended for grinding wheel 125 mm diameter with protection Broad lunch Lightweight machine Constant speed Electronic stable voltage and current Ideal speed rotor provides high quality grinding burrs Asembly sand and smooth transition between the ground and the uncut material because of rubber shock absorber Amortizer ensures smooth operation, reduces vibration and extends the durability of the engine. Without arm vybration syndrome. Grinding wheel diameter / reception Machine without engine Speed 100/120 mm M14 / 22.2 mm cooling the grinding wheel 1200W, 240V 470 mm 130 mm 140 mm 3 kg 3000 rpm Strong and light angle grinder concrete strength 1200 x 3000 RPMs intended for grinding wheel diameter of 180 mm with Guard Broad lunch around the machine head Lightweight machine Constant speed Elektronic stable voltage and current Ideal speed rotor provides high quality grinding burrs Uniformly sand and smooth transition between the ground and the uncut material with rubber shock absorber Grinding wheel diameter / reception without engine Speed 416,00 100/120/180 mm M14 / 22.2 mm cooling the grinding wheel 1200W, 240V 490 mm 190 mm 140 mm 3 kg 3000 rpm / min Absorber for grinding wheels M 14 - M mm diameter DHP-125 NT Innovative hand polishing machines with stepless adjustable rotation speed for dry and wet polishing of concrete and other kinds of stone 1200W, 230V L/min. included grinds ST2- C D = 125 x 22.2 mm 2.9 kg 1 x instructions for use 390,00 The innovative hand-held machines for polishing with progressively adjustable speed rotation for dry or wet polishing of concrete and other types of stone. - Large range of speed control - Connector for cable, wet polishing - Connector to vacuum dry sanding dust. - serial PRCD - flexible protective cover to adjust the working height - portable segment to cover processing corners - Electronic speed control, smooth start, overload protection. HSM 125 Hand grinding machine processing the edges and corners 400,00 Rotor W, 230V 2800 to 11,000 L/min. included grinds ST2- C D = 125 x 22.2 mm 3.4 kg 1 x instructions for use BCD Standard DHP-175 NT 730,00 HAND polishing machine 1200W, 230V L/min. included grinds ST2- C D = 175 x 22.2 mm 5.8 kg 1 x instructions for use DHG 125 Absorber for grinding wheels M14 - M14 Ø70 mm Ø70 mm BCD STANDARD grinding wheel Ø ,00 Ø 180 ROTOR 180 spiral grinding wheel Ø ,00 Ø ,00 Hand machine for grinding of concrete 1400 W, 230 V 8000 l / min. included grinds ST2- C D = 125 x 22.2 mm 2.8 kg 1 x instructions for use 55,00 96,00 132, ,00

12 HAND TOOLS - PNEUMATIC GRINDING fk7025 Pneumatic hammer reception 12.7 for breaking and moaning in granite, marble, a very powerful and robust A hammer for heavy-duty work example. ornaments Adjustable valve for tools with shank 12.7 mm Work with open disk 1.5 kg Pipe diameter 20 mm Pipe height 60 mm Number of strikes per minute Air consumption 420 l / min Mannesmann Demag hammer letters made in Germany Ergonomic handle design for working without fatigue. Soft work already above 1 bar working pressure Frequently attack specific application Soft sequence of shots and finely adjustable impact energy Low vibration opposed to occupational diseases of the hands and arms. md ,00 md ,00 md ,00 md ,00 md ,00 md ,00 High quality cylinder, piston and buksa long shelf life MD 065,066,125 Single shot controlled with button Lower frequency of strikes, powerful punch an ideal ratio of stroke and stroke frequency (reception insert 10.2 mm with swivel joint 1/4 connection coupling for air) 525,00 fk701precisio Pneumatic hammer reception , a simple, high-quality and accurate A hammer for engraving letters with regulating pressure High frequency shock 5 M hose with connection Enhanced hardened stainless internal parts For tools with shank width of 10.2 and 12.7 mm Idealan for engravings and texts 0.65 kg Pipe diameter 17 mm Pipe height 30 mm Number of strikes per minute Air consumption 340 l / min Q6L Pneumatic polisher high performance, very easy and practical for polishing with diahard Ultra light Without danger of electric shock Without brush Small dimensions Ideal polishing with diahard Grinding wheel diameter: 60/100 mm Reception: M14 / 22.2 Speed rpm 4000 : 1.4 kg Pneumatic hammer for engraving letters 490,00 312,

13 DRILLER STANDS Drill D model series Ultra light weight, compact drill rig with integrated vacuum base, laser positioning guide and continuously inclinable up to 45 Drill stand DRILL 50 model series Variable and particularly stable professional stand with a column of stainless steel for drilling up to a diameter of 500 mm, for powerful engines for drilling -stable support to feed resistant to twisting -easy and convenient maintenance guides and sliding track with smooth bearings -drilling column, support, leveling screws, lever feed, main and fittings of stainless steel -place feed, vacuum rate, shall cover made of aluminum alloy resistant to corrosion. Max. drilling diameter / 5002 mm Inclining up to 45 Total travel 670 mm 425 mm 280 mm 1070 mm 21 kg 1 The max. drilling diameter applies to BDK drill motors. 2 with 75 mm spacer Automatic feed BA-50 FOR DRILL 50 Automatic feed DRILLING ba-50 FOR DRILL - 50 fully automatic Governance DRILLING reinforced concrete. BA-50 is intended for the use of specially prepared EN motors (SR 25 mammoth mammoth SR 38, SR 65 and jumbo) The feed to the central rack mounted fast connection, the crown down to a few millimeters to the concrete surface, the clutch feed activated, starting the engine to keep the second sec. BA-50 already does the your business and you can perform other tasks or relax. Simple installation and the second with adapter plate with spring High load capacity feed Built a date for the manual and automatic operation Protection class IP55 Adjustable accurate drilling depth Auto off when drilling with strong vibrations Variable load limits drilling Selection of 90% and 70% of engine power Nominal voltage Feed force Feed speed 1.600,00 48 V 4000 N 0-0,4 m/min 3,5 kg Clamping Ø 60 mm with quick release system (D-160V) quick release plate (D-250V) Low-maintenance and stable sliding guide system (D-160V) Low-maintenance and smooth-running roller guide system (D-250V) Vacuum base incl. vacuum set and leveling screws Integrated spirit level for precise alignment V-support for starting of drilling Laser drilling center indication Incl. tool set D160V D250V Max. drilling diameter 160 mm 250 mm 480 mm 470 mm 280 mm 290 mm 900 mm 950 mm 9,8 kg 14,4 kg Total travel 570 mm 570 mm Inclined drilling up to D350R, D350RS I D400X Drill D serial model High performance drill rig with stable base Transport rollers and quick release plate for bores up to Ø 350 /400 mm Low-maintenance and smooth-running roller guide system (D-350R, D-350RS) Low-maintenance and stable sliding guide system (D-400X) Continuously inclining up to 45 Strong cast base with leveling screws (D-350R, D-400X) Heavy-duty, compact steel welded base With pivot overturn support (D-350RS) Column movable in drilling direction - no extensions for inclined drilling necessary (D-350RS) Easy removable transport wheels quick release plate D-160V D-250V 580,00 720,00 D-350RS 1.090,00 D-400X 990,00 D-350R 910,

14 DRILL14 ECO /DRILL14 Light weight drill stand with integrated vacuum rate and 60 mm clamping neck for drilling up to Ø150 mm Clamping neck 60 mm Gradually adjust the angle to 45 with angle scale Highlight point drilling DRILL 14 ECO 978,00 DRILL ,00 DRILL20 Compact and robust drill stand with additional strut and quick connection to the bore to Ø250 mm Quickly interchangeable plates for motor II 250 mm maximum drilling diameter of 20 mm separation 2-speed feed Gradually adjust the angle to 45 with angle scale Maximum drilling diameter 258 mm (with BDK drill motors) The slope up to mm 330 mm 1020 mm 15kg 950,00 DRILL32/Drill 45 DRILL ,00 Compact and robust drill rig with additional column support and quick release plate for drilling quick release motor plate II Drill 32L/45L for drililing with long core drills DRILL 32L 1.410,00 DRILL ,00 DRILL 45L 1.840,

15 B-40 B-60 B-100 B-25 Durable and handly drill rig with feeding unit with patented roll guide system for drilling diameters up to Ø 350 mm Max. drilling diameter Inclined drilling up to 1.480, mm kg 330 mm 200 mm 950 mm 16 kg Durable drill rig with feeding unit with patented roll guide system for drilling diameters up to Ø 500 mm With high power drill motors Max. drilling diameter 350/390 mm Inclined drilling up to mm 250 mm 1140 mm 26 kg 1.880,00 Durable drill rig with feeding unit with patented roll guide system for drilling diameters up to Ø 700 mm with high power drill motors Can be used with long or extra long core drills. Feeding with replaceable gear rack Patented feeding unit with roll guides (with ball bearings) Foot plate with leveling screws Column up to 60 for- and backwards inclinable Column, foot plate and rolls made of stainless steel Transport wheels (only B-60, B-100) Max. drilling diameter 350/700 mm Inclined drilling up to mm 300 mm 1540 mm 37 kg 2.680,00 Extreme robust drill rig with patented ball-bearing guide system and massive column support for bores up to Ø1000 mm for hydraulic and electrical drilling motors up to 8 kw power Feeding with replaceable gear rack Patented feeding unit with roll guides (with ball bearings) Foot plate with leveling screws Column up to 60 for- and backwards inclinable Column, foot plate and rolls made of stainless steel Transport wheels (only B-60, B-100) Max. drilling diameter mm Total travel of feeding unit 1080 mm Tiltable forwards/backwards up to 20/60 of column 1470 mm 580 mm 525 mm 1650 mm 65,0 kg With quick release spacer, without spacer Ø 500 mm 6.390,

16 DRILLER DRILLER PIPES C1500 C2600 Makita UT W Makita drill Drilling to fi90mm 1/2 + 5/4 Two speeds Engine 1500 W, 220V Drilling to fi255mm 1/2 + 5/4 Two speeds Engine 2600 W, 220V Power: 1300W 5.5 kg Rated speed: / / min Drill rig Drill rig 450,00 490,00 870,00 Drill price Drill price 900, ,00 KB350 Customizable Machines with hydraulic - or petrol engine for the holes in the main channel relationships and sampling on the ground Maximum drilling diameter 354 mm Standard useful length of 450 mm 38 kg 450,00 The machine is supplied with 2 clay screws Tightening spanners, water tank and pressure pipe for exhaust gases When working with gasoline engine. C2400 Drilling to fi205mm 1/2 + 5/4 Two speeds Engine 2400 W, 220V Drill rig Bosch drill Electric machine with two speeds for dry drilling porous concrete, PVC and others. Pipes. Also suitable for drilling holes in the bricks and mortar for climate, heating and ventilation 580,00 Drill price 1.220,00 The collector of water for the crown to fi85mm Vacuum plate for mounting racks on the surface that can not be or should not pllug With electronics for smooth motion and constant voltage and current protection from overheating. Broad handle for stable drilling. Maximum / minimum drill diameter mm Standard useful length of mm 4.3 kg Power 1150 W Speed min ,00

17 DRILLER DK17 DK08 Drilling range: mm Nominal power 1800 W Output power 1200 W Rated speed 540/1700 1/min Total length 450 mm without cable 4,9 kg Drilling Ø c. Rig operated (concrete) mm Hand-held (concrete) mm Hand-held (masonry) mm Tool fixture G 1/2 Mounting neck Ø 60 mm Suitable drill rig type KS13 DK09 Drilling range: mm Nominal power: 1800 W Speeds: 2 Nominal power 1800 W Output power 1200 W Rated speed 540/1700 1/min Total length 485 mm without cable 5,2 kg Drilling Ø c. rig operated (concrete) mm hand-held (concrete) mm hand-held (masonry) mm Tool fixture 1 1/4 Mounting neck Ø 60 mm Suitable drill rig type KS13 Drilling range: mm Nominal power: 2000 W Speeds: 3 Technical Data Nominal power 2000 W Output power 1340 W Rated speed 540/1200/2520 1/min Total length 420 mm without cable 6,3 kg Drilling Ø c. rig operated (concrete) mm hand-held (concrete) mm hand-held (masonry) mm Tool fixture 1 1/4 + Adapter G 1/2 Mounting neck Ø 60 mm 840,00 890, ,00 DK 18 DK11 Drilling diameter mm 1/2 or M33 / 3 Transfer / Speed 1 Speed 6500 min kw, 230 V Slip clutch to Tightening neck diameter of 60 mm 5.5 kg drilling diameter mm spindle 1/2 gears 3 rotation speed min-1 540/1200/2520 motor 2,0 kw, 230 V slipping clutch ja clamping diameter 60 mm weight 5,3 kg 1.041,00 DK16 Drilling range: mm Nominal power: 2000 W Speeds: 3 DK16 DK1603 Nominal power 2000 W 2000 W Output power 1340 W 1340 W Rated speed 540/1200/ /1200/2520 Total length 350 mm 350 mm without cable 5,9 kg 5,9 kg Drilling Ø concrete c. rig operated mm mm hand-held mm mm Tool fixture G 1/2 1 1/4 UNC + G 1/2 Mounting neck Ø 60 mm 60 mm 1.156, ,00 SR 25 MAMMUT Drilling range: mm Nominal power: 3700 W Speeds: 6 SR25 SR25 S Rated Voltage 230 V 230 V Rated current 16 A 16 A Nominal power 3700 W 3700 W Output power 2700 W 2700 W Rated speed (6 steps) /min /min Total length without handle 440 mm 440 mm without cable 14,7 kg 14,7 kg Drilling Ø concrete c mm mm Tool fixture 1 1/4 1 1/4 Foot fastening Standard 4 x M8 with groove 10 x 4, ,00

18 SR 38 DK26 DK 42 B SR 68 JUMBO New water cooled SR motor with large power reserves, 3 gears and 6 electronic rotation speeds for exceptionally wide drilling diameter of Ø mm. Drilling range: mm Nominal power: 2600 W Speeds: 3 Drilling range: mm Nominal power: 3900 W Speeds: 3 New water cooled 400V-SR motor with essential power reserves, 3 gears and 6 electronic rotation speeds for deep and exceptionally challenging bores of Ø mm. Drilling diameter mm Spindle thread 1 1/4 Gears 18 (3 mechanical x 6 electrical) Rotation speed (18 steps) min-1 3,7 kw / 230 V Slipping clutch yes kg 16, ,00 DK26 DK26 L DK26 S Nominal power 2600 W 2600 W 2600 W Output power 1870 W 1870 W 1870 W Rated speed 320/630/ /480/ /910/1420 Total length without handle 490 mm 490 mm 490 mm without cable 11,6 kg 11,6 kg 11,6 kg Drilling Ø concrete c mm mm mm Tool fixture 1 1/4 1 1/4 1 1/4 Foot fastening Standard 4 x M8 with groove 10 x 4,3 DK42 B DK42 BS DK42 BL Rated Voltage 400 3~ V 400 3~ V 400 3~ V Nominal power 3900 W 3900 W 3900 W Output power 3000 W 3000 W 3000 W Rated speed 160/310/ /460/ /260/410 Total length without handle 540 mm 540 mm 540 mm without cable 19 kg 19 kg 19 kg Drilling Ø concrete c Tool fixture 1 1/4 1 1/4 1 1/4 Foot fastening Standard 4 x M8 with groove 10 x 4,3 Drilling diameter mm Spindle thread 1 1/4 or M33/3 Gears 18 (3 mechanical x 6 electrical) Rotation speed (18 steps) min ,5 kw / 400 V Slipping clutch yes kg 16, , , ,00 DK32 Drilling range: mm Nominal power: 3200 W Speeds: 3 DK32 DK32 S Nominal power 3200 W 3200 W Output power 2300 W 2300 W Rated speed 230/460/720 1/min 300/590/930 1/min Total length without handle 488 mm 488 mm without cable 11,9 kg 11,9 kg Drilling Ø concrete c mm mm Tool fixture 1 1/4 UNC 1 1/4 UNC Foot fastening Standard 4 x M8 with groove 10 x 4, ,00 SR 65 JUMBO New water cooled SR motor with sufficient power reserves and 6 electronic rotation speeds for bores up to Ø 500 mm. DK52 Drilling range: mm Nominal power: 5200 W Speeds: 3 DK52 DK52 S Rated Voltage 400 3~ V 400 3~ V Nominal power 5200 W 5200 W Output power 4000 W 4000 W Rated speed 1/min 130/260/ /310/490 Total length without handle 580 mm 580 mm without cable 22,9 kg 22,9 kg Drilling Ø concrete c mm mm Tool fixture 1 1/4 1 1/4 Foot fastening Standard 4 x M8 with groove 10 x 4, ,00 SR 75 JUMBO Drilling range: mm Nominal power: 7500 W Speeds: 15 SR7508 SR 75 S / SR 7508 S Rated Voltage 400 3~ V 400 3~ V Rated current 15 A 15 A Nominal powe 7500 W 7500 W Output power 5700 W 5700 W Rated speed (15 steps)1/min Total length without handle 620 mm 620 mm without cable 19,5 kg 19,5 kg Drilling Ø concrete c mm mm Tool fixture M33/3 1 1/4/ M33/3 Foot fastening 8 x M8 with groove 10 x 4, ,00 Drilling diameter mm Spindle thread 1 1/4 or M33/3 Gears 6 Rotation speed 140/ 175/ 205/ 240/ 270/ 305 min-1 7,5 kw, 400 V Slipping clutch yes kg 18, ,00 35

19 DRILLER DRILLER B600 The variable and very robust drill stand system for hydraulic motors for drilling holes up to about 600 mm Variable and highly configurable system Feed rate over the tooth rack The feed unit ball bearings The power rate with adjustable screws Extremely sturdy upright profile Profile drill the rails from Kombi Bus-system and therefore, if necessary, extended (up to max. 6 m) Maximum drilling diameter 600 mm Working length 600 mm 460 mm 360 mm 1200 mm 29.0 kg without feed 15.3 kg feed 3990,00 WITH INCLINING OPTION: 5908,00 U30010 Variable, robustai and multiple removable rack for drilling, hydraulic system and electric motor for drilling holes up to about 300 mm in the toughest conditions Variable and highly configurable system Feed rate over the tooth rack The feed units over 6 beds The power rate with adjustable screws Fuse headers nestepenovano adjustable U in all directions nestepenovano adjustable crown and moving in the direction of drilling (in hair extension drilling is not required) B800 The variable and extremely robust with double sliding-stand drilling system for hydraulic motors for drilling holes up to about 800 mm (module carrier radial disc RD 3500) Variable and highly configurable system Feed rate over the tooth rack The feed unit ball bearings The power rate with adjustable screws Extremely sturdy upright profile Profile drill the rails from Kombi Bus-system and therefore, if necessary, extended (up to max. 6 m) Maximum drilling diameter 800 mm Working length 600 mm 650 mm 730 mm 1200 mm 54.2 kg without feed 35.7 kg feed Maximum drilling diameter 300 mm Working length 800 mm 530 mm 280 mm 1000 mm (1200 mm *) 1000 mm crown Setting crown 90 backwards 45 forward 90 to each side in the direction of drilling interchangeably 22.3 kg without feed feed with adjustable cross 6.6 kg Water supply trolley WT ,00 WITH INCLINING OPTION: 7650, ,00 B2000 B1000D The machine for drilling large diameter for high demands and drilling diameter up to about 1200 mm (1500 mm) Short preparation thanks to rapid installation system Water supply via central shaft and flange WITH SPINDLE AND HYDRAULIC MOTOR , ,00 The maximum drilling diameter of 1200 mm (1500 mm) Maximum lift (flange) 550 mm Maximum lift (1 1/4 UNC) 450 mm with support and Hydro engine kg without Caliper and Hydro engine kg Hydro unit DA kw, 340 bar 0-52 l / min kg (hydraulic oil) WITHOUT SPINDLE AND HYDRAULIC MOTOR : Water supply trolley WT 35 Large portable 35 liter vessel with build-in battery driven pump and transport wheels for supply of core drill machines with cooling water Compared with usual manual 10 liter water supply vessels the WT-35 saves more than 50% of working time. Can be used on construction sites for reduction of dust exposure from different cutting machines (floor saws, hand saws etc.). large volume of 35 liter for continuous operation without interrupts 490,00 build-in battery driven pump integrated battery with long operation and short charging time water flow steplessly adjustable large air filled transport wheels long hose with Gardena-coupling Volume 35 l Hose length 10 m Charging time of battery 4 h Charging voltage of battery 230V Operating time 8 h Waterflow l/min 0-4 Max. water pressure 6 m Dimensions LxWxH 330x400x950 mm without water 14,0kg 36 37

20 Slurry separator VA-10 EQUIPMENT FOR DRILLER EQUIPMENT FOR DRILLER Equipment for diamond crown and drilling rigs (Other equipment and material for fixing on request) Need to be installed between the core drilling machine and aspirator (vacuum cleaner) and allows the removing of soiled liquids with a common wet / dry cleaner, whereby the slurry doesn t get into the hood - it is disposed directly by the separator s build-in pump. VGP The vacuum plate aluminum with valve for radiation and threaded rod with nut SP1 Telescopic For quickly fixing drill, length up to 3150 mm Significant time saving due to continuously slurry disposal without interrupts for emptying and cleaning of the hood Saves the hood, because it processes dry, clean air only No loss of suction power by the filter pollution No filter wear Build-in automatics prevents aspiration of dirt water by the hood High-quality slurry pump with dry run protection 1.780,00 Anchor anchoring M12, Type Rawel 3.50 Hammer fixings M Hammer fixings M12 (diameter 15 mm) 0.37 Hammer fixings M12 (16 mm) 0.40 Impact tool M Impact tool M Threaded rod M12 hexagon nut M Threaded rod M12 with big nut Staedtler pens (100 pieces) Pencils FEIN (100 pieces) Copper ring (100 pieces) /4, 1/2 SW41 SW22 Extra 100 mm Extra 200 mm 24,00 Extra 300 mm 32,00 Extra 400 mm Extra 500 mm 50,00 Adapter cutters 1 1/4 M r 1/2 M BBT Z M 38 Z Adapter cutters 1 1/4 W r 1/2 W BBT M M 38 M Adapter for core BBT Z r1 / 2 W Adapter for core BBT M r 1/2 M M = male, female= Z WBK Tank volume 72,00 8 l 200 mm 200 mm 550 mm 2.3 kg 340 mm 250 mm 4 kg 270, mm 230,00 Accessories for drill machines Other accessories are available on request. Anchor bolt M12, type Rawel 3,50 Standard anchor bolt M12 (Ø 16 mm) 0,32 Heavy load anchor (many designs) 0,37 Set FDBB consists of spindle-bolt 0,40 FDBB, big screw nut and 25 pieces Anchor bolt FDBB 16/50 anchor bolt FDBB 16/50 (25 pcs.) Dowel tool M12 Thread rod M12 with hexagon nut M30 Thread rod M12 with big screw nut Shear pins Milwaukee (100 pcs) Shear pins FEIN (100 pcs) 48,00 Copper rings (100 pcs) 99,00 WBM 10 l of water system of metal with pressure gauge and safety valve Tank volume 159,00 10 l 220 mm 220 mm 600 mm 5.5 kg Accessories for diamond core drilling machines Nut with swivel joint Compensates the inclination of the thread rod Fits to all thread rods Reduces the risk of breakage of the thread rod Allows the exact positioning of drill rigs with minimal force (only design with integrated spring) Thread rod with self cutting thread for concrete No anchor bolt neccessary Very high pull-out force Saves a lot of time for mounting Multiple usable (empirical value appr tim) Extensions for diamond core drills 1 1/4 SW mm 200 mm 300 mm 400 mm 500 mm 1/2 SW mm 200 mm 300 mm 400 mm 500 mm 1 1/4 1/2 VP80 The compact vacuum pump with 5 l tank and powder coated housing The consumption of 0.2 kw, 230 V Front tank 80 l / min Tank volume 5 l 350 mm 220 mm 280 mm 10 kg ,00

21 ACCESSORIES MULTI-DISC GRINDING MACHINES FI ,00 265, V FI-Box in case of hard rubber with a 1 x 32A 6h, 1 x 16A 6h and 2 x shock-proof 3.0 kg FI FI-Box in case of hard rubber with 1 x CEE 1h and 3 x earthed 2.8 kg DBS-460-3H New, innovative 4.0kW / 230V grinder with three disks, high-performance. Transmission and variable speed control for easy polishing and grinding on the same surface ,00 Wet- /dry-vacuum cleaner RNT 1225 With automatic filter cleaning High Performance Initial current limiter Automatic power switch In combination with a connected power tool Automatic, electromagnetic filter cleaning by vibrations 5 meter suction hose Tank for dust without edges Dust level indicator with automatic switch-off 850,00 DBS-520-3H New, innovative 7.5kW / 400V grinder with three disks, high-performance. Transmission and variable speed control for easy polishing and grinding on various hard surfaces, even stone floors ,00 CLEANER NL370TN Robust, powerful water / dry vacuum cleaner with a tank made of stainless steel, in addition to 3 m hose, 3 engines and equipment Consumption 3 x 1.1 kw, 230 V The air quantity of 9000 l / min Tank volume 70 l 22 kg 470 mm 470 mm 1060 mm DBS-620-4H new innovative extremely powerful 7,5 kw / 400 V four-discs grinding machine with high-class gear transmission and variable rotation speed for large projects on uneven surfaces of soft and hard floors 8.990,00 870,

22 DBS-820-3H / 820-3H DBS Remote New, innovative, high-performance 11kW / 400V grinder with three disks. Transfer high-performance wireless remote control for very large projects (only DBS remote 820-3H). - CNC mechanical transmission is me off from high-quality aluminum alloy, - High performance transfer rates. The gears are made of special steel alloys, high capacity and long life, - Always the optimal position of the machine relative to the surface, thanks to the flexible position of the cutting head, - The handle is height adjustable, - The speed of rotation is easily controlled through a frequency converter of high performance, - Stabile and easy tank water due to centrifugal casting, - LED display, - Control panel with stop button in case of emergency, - Double connection for industrial vacuum cleaner, for dust-free, - Easy to control the flow of water, - Swivel, jockey wheel to adjust the contact pressure, - Electric adjustment of the contact pressure, - Elastic mounted sanding head reduces vibration and improves surface quality, - Universal holder for mounting of metal and organic set of tools, - DRS-Lock connector system for grinding tools, - Wireless remote control of all main functions of the machine (only DBS remote 820-3H). PRICE WITH RC: , ,00 MULTI-DISC GRINDING MACHINES DBS-820-3H 820-3H DBS Remote 11 kw / 400 V 11KW/400 V Grinding width 780 mm 780 mm Quantity of grinding heads / diamond tools pcs. 3 / 9 3/9 Water tank 30 L 10 L Rotation speed main plate min Rotation speed of satellites min mm 2580 mm 800 mm 800 mm 1200 mm 1200 mm 480 kg 530 kg SINGLE DISC GRINDING MACHINES DBS 250 Light, handy and very powerful grinding machine with 230V power connection for wet and dry grinding of various stone floors Elastic tool fixing system for reduction of vibrations and compensation of ground unevennesses Excentric adjustment system for grinding angle adjustment Integrated spirit level for precise leveling Folding handle for transport Stepless adjustment of the handle working height Easily reachable emergency stop button Rotatable grinding head for grinding close to the walls Removable protection cover for grinding in corners Water connection for wet grinding Brush seal ring and large vacuum cleaner Connection for dust-free grinding DRS-LOCK - fixing system for grinding tools grinding width 250 mm motor 2,2 kw, 230 V rotation speed min length 800 mm width 420 mm transport height 860 mm weight 60.0 kg 1.390,00 MCP E17 Powerful single disc grinder width 420 mm, high-speed transmission, for long life, optimum performance. Suitable for dry and wet cleaning and polishing concrete and stone floors. The delivery includes: Water PPN cleaning brush Fi 405mm/0.75mm PAD- holder Fi 420mm The handle is height adjustable Electric cable (10m) Including the necessary equipment. motor Grinding width Rotation speed 1,6 kw / 230 V 420 mm 154 min-1 44 kg Robust gearbox, maintenance-free The large wheels (150 mm) for convenient transport 1.280,00 DBS-400 plus Powerful, robust and simple in use single disc machine for grinding of miscellaneous surfaces. Suitable for grinding and polishing of terrazzo and concrete as well as for removing epoxy adhesives, paints and pollutions. Also suitable for wet grinding. Easy to operate Dust extraction outlet for dust-free processing With water connection for wet grinding Exceeding grinding performance Powder-coated components Incl. grinding base plate for mounting of 3 or 6 diamond or PCD tools DRS-LOCK fixing system for grinding tools Grinding width 400 mm 4 kw, 400 V Rotation speed min mm machine / handle 410/730 mm 1000 mm ca. 100 kg 1.890,00 DBP-500 Power and fast polishing machine 2,5kW / 230V with integrated dust removal, cleaning, polishing various surfaces. High Speed 1400min-1 for large areas, Flexible PAD-holder ensures a stable contact with the floor and the optimal polishing results, The handle is height adjustable, Integrated system for collecting dust filter, Tilting handle for easy transport, Suitable for almost any surface: concrete, plastic, tiles, ceramics, stone, wood, paints and so on. High-speed polishing machine / machine for polishing high speed 2,5 kw / 230 V Grinding width 510 mm Rotation speed min kg ,00

23 MACHINE FOR MILLING CONCRETE EFS 135 Universal grinder 230V - very durable and comfortable, available additional water tank for wet cleaning and polishing. Extremely versatile due to various tool A wide range of applications thanks to the various extended their tools Hard metal frame, Quick-changing tools, Adjustable handle management, Handles for transport, Dust extraction port for dust-free working (connection to an industrial vacuum cleaner) Additional water tank 12l cleaning, watering and lubrication. Applications / Application: Tiles, slabs, etc. - Grouting, cleaning, application of funds, polishing and smoothing of the irregular edges and joints. Varnishes - compaction, filling, polishing, grinding, coating, cleaning, modulation. Floor surfaces - remove deposits of dust and manipulation. Maintenance floor - cleaning and polishing ,00 FB 600 The machine for milling concrete 15 kw motor hoods tool 530 mm tool for moaning about 450 mm of tools for milling about 460 mm Four-wheel drive Feed power to fine Regulation, a manual feed ,00 CT 320 The machine for milling concrete Desktop: 320 mm AC motor: 11 kw Dimensions: 110 x 110 x 60 : 230 kg (with drum and knives) The diameter of the blade: 80 mm Acceptance of a vacuum cleaner: 70 mm Load control of the machine via an ammeter Hour meter The machine is of our production, and we have it in stock. Tools / head moaning and milling we do not have in stock and need to produce. The time required to produce the head is about 7 days. When milling used ring millers and their numbers can vary depending on the needs. DBB-700 / burnisher HIGH SPEED POLISHING MA- CHINE 4.000,00 Polishing Machine high speed 7.5kW / 400V with adjustable speed rotation to 2500min-1 for daily polishing, increased shine, for the thermal treatment of integrated concrete. Applications / Application: Polishing large surfaces with diamond-pads Increased effectiveness of treatment with lithium, Improvement in the hardness of the concrete and the wear resistance due to the thermal treatment of concrete, Improved surface gloss. Powerful motor 7.5kW / 400V The handle is height adjustable, Automatic tensioning system V-belt, High quality inverter to adjust the speed from 0 to 2500 min-1, Large daily production due to high power engines. Grinding width Rotation speed 7,5 kw / 400 V 700 mm min kg 6.200,00 K-320G The machine for milling concrete Hubbell The machine for milling concrete Working width: 160 mm Working width 54 Kg 230 V, single phase 50 Dimensions 93 x 100 x 34 cm PRICE: ON REQUEST Working width: 320mm Working depth: 0-6mm Operating capacity: m2 / h Electric motor: 7.5KW / 380V 3 phase Drum diameter: 80mm For hard concrete strength C50 44 PRICE: ON REQUEST 45

24 680GC Saw Polyester air filter designed specifically for wet cutting Operates EuroMAX bar and chain consumables up to 35 cm Multifunction lever controls choke, throttle advance, run and stop modes Extended drive sprocket adapter offers easy chain assembly Deep cutting solution for obstructed or small openings Cut squares as small as 10 cm x 10 cm) Easy-to-start in all weather Engine Type 2-stroke, Air Cooled Displacement 76.5 cc (4.7 cu-in) Horsepower 3.7 kw (5 9,500 rpm Torque 4.1 Nm at 6,500 rpm Engine Speed /- 500 rpm (max) / 2,800-3,200 rpm (Idle) Chain Speed at Max Power 34.5 m/s 9.5 kg powerhead only Dimensions 46 cm L / 29 cm H / 25 cm W CHAIN MACHINES PRICE: ON REQUEST 814PRO Saw It may be small, but with as much power as its big brother the 890 Series, the 814PRO is ready for the big jobs. Lighter than other hydraulic saws with the ability to cut perfectly square openings as small as 3 ½ inches (9 cm), the 814PRO is a natural for utility work and other applications where a mix of portability and power are required. 32 cm bar and chain Bar Speed Chain Speed 6.8 kg with 32 cm 8800 rpm 25 m/s, free running Powerhead Dimensions 36.3 L / 28.7 cm H / 23.4 cm W Torque 84 in-lbs Horesepower 11.5 hp Hydraulic Supply 8 gpm (30 lpm), 2500 psi (172.5 bar) Noise Level 88 db 1 m Vibration Level 3.5 m/s (front handle) Water Supply Minimum 20 psi (1.5 bar) PRICE: ON REQUEST 890F4-FL Saw The ICS 890 Series hydraulic cutting system offers the superior strength of FORCE4 technology. From the redesigned, more durable rear handle, to the easy to replace drive sprocket, this saw is engineered to stand up to your toughest jobs. In a package that exceeds industry standards this sleek powerhouse is packed with features designed to make it work as hard as you do. PRICE: ON REQUEST PRICE: ON REQUEST 12.4 kg with 38 cm bar and chain Bar Up to 63 cm Speed 6100 rpm Powerhead Dimensions 58.5 cm L / 26.5 cm H / 24 cm W Torque 122 in-lbs Horesepower 11.5 hp Hydraulic Supply 8 gpm (30 lpm), 2500 psi (172.5 bar) Noise Level ft (1 m) Vibration Level 2 m/s (front handle); 6 m/s (rear handle) Water Supply Minimum 20 psi (1.5 bar) 695F4 Saw Use on concrete, stone, masonry, ductile iron pipe, cast iron pipe and more Most versatile petrol-powered saw New piston and cylinder lowers engine temperature Longer life muffler with reinforced internal baffle Easy-to-start with higher energy ignition system New easy-to-tune carburetor Engine Type Displacement Horsepower Torque Engine Speed Chain Speed at Max Power Dimensions 2-Stroke, Air Cooled 94cc (5.7 cu-in) 4.8kW (6.4 hp) at 9000 rpm 5.7 Nm at 7200 rpm 9,300 +/- 150 rpm (max)/2,700 +/- 100 rpm (idle) 28 m/s 9.5 kg powerhead only 46cm L / 36cm H / 30cm W PRICE: ON REQUEST 890F4 Saw PRICE: ON REQUEST The ICS 890 Series hydraulic cutting system offers the superior strength of FORCE4 technology. From the redesigned, more durable rear handle, to the easy to replace drive sprocket, this saw is engineered to stand up to your toughest jobs. In a package that exceeds industry standards this sleek powerhouse is packed with features designed to make it work as hard as you do kg with 38 cm bar and chain Bar Up to 63 cm Speed 6100 rpm Powerhead Dimensions 58.5 cm l / 26.5 cm H / 24 cm W Torque 122 in-lbs Horsepower 11.5 hp Hydraulic Supply 8 gpm (30 lpm), 2500 psi (172.5 bar) Noise Level 107 db at 1 m Vibration Level 2 m/s (front handle); 6 m/s 2 (rear handle) Water Supply Minimum 20 psi (1.5 bar) 46 47

25