Design and Analysis of a steering Rack of an ATV for different materials under static loading conditions
|
|
|
- Annabel Griffith
- 5 years ago
- Views:
Transcription
1 Design and Analysis of a steering Rack of an ATV for different materials under static loading conditions 1 Niraj Kulkarni, 2 Pritam Wani 1 BE Mechanical JNEC Aurangabad 2 TE Mechanical MIT T Aurangabad Abstract: Steering system constitutes an important role in the ergonomics of the vehicle. There are various types of steering system used in different ATV s. Rack and Pinion type of steering system are widely used in ATV s because of their lighter weights and comfort feeling of the driver. The rack and pinion steering systems are also used in lower automotive vehicles and also in light duty vehicles in the world. It constitutes about 50 percent of steering system in worldwide automotive steering sector.the steering rack can be made from various types of materials like PCC, BRASS, MILD STEEL, various alloys containing different configurations at different conditions as per requirement of operations. Rack is also used in door opening and closing of mechanical components. The main aim of this paper is to decide the proper material for the steering rack and to compare its analysis reports for various materials taken under considerations. Designing software CATIA & SOLIDWORKS. Analysis in ANSYS 16.0 edition. Main geometry for design considered for physical product is Ackerman steering geometry. Keywords: STEERING RACK, Materials, static loading Introduction: Rack and Pinion steering system are used in various vehicles in which rack is subjected to various loading conditions and various shear forces acting on it. There are various types of materials considered safe for the manufacturing of rack. The main aim of rack is to transmit rotary motion received from pinion to the linear motion and respectively control the motion of steering knuckle to control the directions of the respective left or right wheel in the angle of the required steering geometry. Material selection: The basic materials selected for the testing are 1. Plain Carbon Steel 2. AISI Brass 4. Rubber polymer (synthetic) There were various materials available for study but the classification of materials chosen was done accordingly to the most distinct categories to be considered for clear difference between materials. Design: The design of rack was done in Solidworks. The design specifications are as follows Module=2 Rack Length= 300 mm Diameter of rack= 22 mm Minimum Number of teeth on rack= 20 for 44 degree of turn of front wheel. Rack subjected to force= N Designing Model: 1. Plain Carbon Steel: Mass grams 2. Brass: IJEDR International Journal of Engineering Development and Research ( 654
2 Mass grams 3. AISI 4130: Mass grams 4. Rubber: Mass grams The above all designs show that the weight of rack changes with change in material properties and configurations. Analysis Reports: ANSYS is used as analysis software. The various static structural reports generated for different materials are as follows 1. Plain Carbon Steel : MESH MODEL OF PCC IJEDR International Journal of Engineering Development and Research ( 655
3 ON MODEL EQUIVALENT STRESS REPORT 2. Brass: MESH MODEL OF BRASS RACK TOTAL DEFORMATION OF BRASS RACK 3. RUBBER : IJEDR International Journal of Engineering Development and Research ( 656
4 MESH MODEL OF RUBBER RACK TOTAL DEFORMATION OF RUBBER RACK 4. AISI 4130 MESH MODEL OF AISI 4130 RACK IJEDR International Journal of Engineering Development and Research ( 657
5 TOTAL DEFORMATION OF AISI 4130 RACK Conclusion: The above design and analysis reports proves that the Rubber & Brass are not suitable materials for the rack as they won t sustain the required amount of force under loading conditions. AISI 4130 & PLAIN CARBON STEEL can be used as material for the manufacturing of rack according to the analysis reports above mentioned. The reports also prove that the weight of rack is purely affected by the selection of material. REFERENCES: 1. Gillespie, Thomas D., Fundamentals of Vehicle Dynamics. Society of Automotive Engineers, Inc., Pennsylvania, Vehicle Dynamics Terminology- SAEJ670, Revise Material Science V.D. Kodgire. 4. Design of machine elements V.B. Bhandari 5. William F. Milliken and Douglas L. Milliken, 1995, Race Car Vehicle Dynamics, Society of Automotive Engineers, Inc. IJEDR International Journal of Engineering Development and Research ( 658
DESIGN AND ANALYSIS OF PUSH ROD ROCKER ARM SUSPENSION USING MONO SPRING
Volume 114 No. 9 2017, 465-475 ISSN: 1311-8080 (printed version); ISSN: 1314-3395 (on-line version) url: http://www.ijpam.eu ijpam.eu DESIGN AND ANALYSIS OF PUSH ROD ROCKER ARM SUSPENSION USING MONO SPRING
Design of Suspension and Steering system for an All-Terrain Vehicle and their Interdependence
Design of Suspension and Steering system for an All-Terrain Vehicle and their Interdependence Saurabh Wanganekar 1, Chinmay Sapkale 2, Priyanka Chothe 3, Reshma Rohakale 4,Samadhan Bhosale 5 1 Student,Department
DESIGN AND ANALYSIS OF TUBULAR CHASSIS OF GO-KART
DESIGN AND ANALYSIS OF TUBULAR CHASSIS OF GO-KART Prashant Thakare 1, Rishikesh Mishra 2, Kartik Kannav 3, Nikunj Vitalkar 4, Shreyas Patil 5, Snehal Malviya 6 1 UG Students, Department of Mechanical Engineering,
Design & Manufacturing of an Effective Steering System for a Formula Student Car
Design & Manufacturing of an Effective Steering System for a Formula Student Car Nikhil N. Gitay 1, Siddharth A. Joshi 2, Ajit A. Dumbre 3, Devesh C. Juvekar 4 1,2,3,4 Student, Department of Mechanical
ISSN: [Patil et al., 5(10): October, 2016] Impact Factor: 4.116
![ISSN: [Patil et al., 5(10): October, 2016] Impact Factor: 4.116](/thumbs/83/88212336.jpg "ISSN: [Patil et al., 5(10): October, 2016] Impact Factor: 4.116")
IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY DESIGN AND ANALYSIS OF TELESCOPIC HALFSHAFT FOR AN ALL-TERRAIN VEHICLE (ATV) Chirag Patil *, Sandeep Imale, Kiran Hiware, Sumeet
Design and optimization of Double wishbone suspension system for ATVs
Design and optimization of Double wishbone suspension system for ATVs Shantanu Garud 1, Pritam Nagare 2, Rohit Kusalkar 3, Vijaysingh Gadhave 4, Ajinkya Sawant 5 1,2,3,4Dept of Mechanical Engineering,
Design and Analysis of suspension system components
Design and Analysis of suspension system components Manohar Gade 1, Rayees Shaikh 2, Deepak Bijamwar 3, Shubham Jambale 4, Vikram Kulkarni 5 1 Student, Department of Mechanical Engineering, D Y Patil college
DESIGN METHODOLOGY FOR STEERING SYSTEM OF AN ATV
International Journal of Mechanical Engineering and Technology (IJMET) Volume 7, Issue 5, September October 2016, pp.272 277, Article ID: IJMET_07_05_027 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=7&itype=5
DOUBLE WISHBONE SUSPENSION SYSTEM
International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 5, May 2017, pp. 249 264 Article ID: IJMET_08_05_027 Available online at http:// http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=8&itype=5
Finite Element Modeling and Analysis of Vehicle Space Frame with Experimental Validation
Finite Element Modeling and Analysis of Vehicle Space Frame with Experimental Validation Assoc. Prof Dr. Mohammed A.Elhaddad Mechanical Engineering Department Higher Technological Institute, Town of 6
Design And Analysis Of Two Wheeler Front Wheel Under Critical Load Conditions
Design And Analysis Of Two Wheeler Front Wheel Under Critical Load Conditions Tejas Mulay 1, Harish Sonawane 1, Prof. P. Baskar 2 1 M. Tech. (Automotive Engineering) students, SMBS, VIT University, Vellore,
Vinayak R.Tayade 1, Prof. A. V. Patil 2. Abstract
FINITE ELEMENT ANALYSIS OF TRACTOR TROLLEY CHASSIS Abstract Vinayak R.Tayade 1, Prof. A. V. Patil 2 1 P.G.Student, Department of Mechanical Engineering, S S G B COE&T, Bhusawal, Maharashtra, (India) 2
Design and Analysis of Spring-Ball Clutch Torque Limiter
Design and Analysis of Spring-Ball Clutch Torque Limiter Nasiket M. Gawas, Manali S. Patkar, Prasad B. Gawade 1 B.E Student, B.E Student, 3 B.E Student Mechanical Engineering, Finolex Academy of Management
Design Methodology of Steering System for All-Terrain Vehicles
Design Methodology of Steering System for All-Terrain Vehicles Dr. V.K. Saini*, Prof. Sunil Kumar Amit Kumar Shakya #1, Harshit Mishra #2 *Head of Dep t of Mechanical Engineering, IMS Engineering College,
DESIGNING OF THE RACK AND PINION GEARBOX FOR ALL TERRAIN VEHICLE FOR THE COMPETITION BAJA SAE INDIA AND ENDURO STUDENT INDIA
DESIGNING OF THE RACK AND PINION GEARBOX FOR ALL TERRAIN VEHICLE FOR THE COMPETITION BAJA SAE INDIA AND ENDURO STUDENT INDIA Omkar Diliprao Suryavanshi 1, Prathmesh Prasad Sathe 2, Mahesh Ashokrao Takey
Design & Analysis of Steering System for a Formula Student Car
Design & Analysis of Steering System for a Formula Student Car Dinesh Babu S. 1, Farug H. 2, Tanmay Mukherjee 3 UG Student, 3rd year, Dept. of Mechanical Engineering, Kumaraguru College of Technology,
HARMONIC RESPONSE ANALYSIS OF GEARBOX
HARMONIC RESPONSE ANALYSIS OF GEARBOX Rishav Ranjan, Sindhu Srinath and Shanmukha Nagaraj Departmental of Mechanical Engineering, RVCE, Bangalore, India E-Mail: rishav.singh94@gmail.com ABSTRACT Gearbox
Design, Modelling & Analysis of Double Wishbone Suspension System
Design, Modelling & Analysis of Double Wishbone Suspension System 1 Nikita Gawai, 2 Deepak Yadav, 3 Shweta Chavan, 4 Apoorva Lele, 5 Shreyash Dalvi Thakur College of Engineering & Technology, Kandivali
Design, Analysis &Optimization of Crankshaft Using CAE
Design, Analysis &Optimization of Crankshaft Using CAE Dhekale Harshada 1, Jagtap Ashwini 2, Lomte Madhura 3, Yadav Priyanka 4 1,2,3,4 Government College of Engineering and Research Awasari, Department
New Frontier in Energy, Engineering, Environment & Science (NFEEES-2018 ) Feb
RESEARCH ARTICLE OPEN ACCESS DESIGN AND IMPACT ANALYSIS OF A ROLLCAGE FOR FORMULA HYBRID VEHICLE Aayush Bohra 1, Ajay Sharma 2 1(Mechanical department, Arya College of Engineering & I.T.,kukas, Jaipur)
Design and Optimization of Steering System
Design and Optimization of Steering System Hardikkumar Gadher 1, Tejashkumar Patel 2, Chirag Modi 3, Zeel Bhojani 4 1,2,3,4 Chandubhai S Patel Institute of Technology, CHARUSAT, Gujarat, India ---------------------------------------------------------------------***---------------------------------------------------------------------
Increase Factor of Safety of Go-Kart Chassis during Front Impact Analysis
IJIRST International Journal for Innovative Research in Science & Technology Volume 3 Issue 04 September 2016 ISSN (online): 2349-6010 Increase Factor of Safety of Go-Kart Chassis during Front Impact Analysis
Design, analysis and mounting implementation of lateral leaf spring in double wishbone suspension system
Design, analysis and mounting implementation of lateral leaf spring in double wishbone suspension system Rahul D. Sawant 1, Gaurav S. Jape 2, Pratap D. Jambhulkar 3 ABSTRACT Suspension system of an All-TerrainVehicle
STATIC ANALYSIS ON BEVEL GEAR USING STRUCTURAL STEEL, GRAY CAST IRON, AND STAINLESS STEEL
STATIC ANALYSIS ON BEVEL GEAR USING STRUCTURAL STEEL, GRAY CAST IRON, AND STAINLESS STEEL Prateek Srivastava 1, Rishabh 2, Zubair Irshad 3, Pankaj Kumar Singh 4 Graduate Students Mechanical Engineering,
Design and Analysis of Front Lower Control Arm by Using Topology Optimization
Design and Analysis of Front Lower Control Arm by Using Topology Optimization Prashant Gunjan 1, Amit Sarda 2 12 Department of Mechanical Engineering, Christian College of Engineering and Technology, Bhilai
Compelete analysis of chasis design of automobile vehicle using finite element method
Volume: 04 Issue: 3 Mar -2017 www.irjet.net p-issn: 2395-0072 Compelete analysis of chasis design of automobile vehicle using finite element method 1 Vidyadhar biswal, 2 Rohit goyal, 3 Mandeep chhabra,
Structural Analysis of Differential Gearbox
Structural Analysis of Differential Gearbox Daniel Das.A Seenivasan.S Assistant Professor Karthick.S Assistant Professor Abstract- The main aim of this paper is to focus on the mechanical design and analysis
Effect of Geometry Factor I & J Factor Multipliers in the performance of Helical Gears
Effect of Geometry Factor I & J Factor Multipliers in the performance of Helical Gears 1 Amit D. Modi, 2 Manan B. Raval, 1 Lecturer, 2 Lecturer, 1 Department of Mechanical Engineering, 2 Department of
Design and Analysis of Steering Knuckle Component For Terrain Vehicle
Design and Analysis of Steering Knuckle Component For Terrain Vehicle V.S.Shaisundaram 1, L.Karikalan 2, V.Vignesh 3, R.Tamilmani 4, M.Akash 5 1 Assistant Professor, Department Of Automobile Engineering,
Development of Motorized Car Jack
Development of Motorized Car Jack Ravi Kumar D Assistant Professor Mechanical Engineering SRM University Shubham Choudhary U.G. Student Mechanical Engineering SRM University Devanshu Pasbola U.G. Student
Design and Analysis of a Space Frame Tubular Chassis for a Formula Student car
Design and Analysis of a Space Frame Tubular Chassis for a Formula Student car Apoorva Tyagi Graduate Student, Department of Mechanical and Manufacturing Engineering, Manipal Institute of Technology, Manipal,
ISSN: [Raghunandan* et al., 5(11): November, 2016] Impact Factor: 4.116
![ISSN: [Raghunandan* et al., 5(11): November, 2016] Impact Factor: 4.116](/thumbs/75/72421287.jpg "ISSN: [Raghunandan* et al., 5(11): November, 2016] Impact Factor: 4.116")
IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY DESIGN AND ANALYSIS OF GO-KART CHASSIS D.Raghunandan*, A.Pandiyan, Shajin Majeed * Mechanical Department, Final year, Saveetha
Design and Analysis of Go-kart Chassis
Design and Analysis of Go-kart Chassis Sannake Aniket S. 1, Shaikh Sameer R. 2, Khandare Shubham A. 3 Prof. S.A.Nehatrao 4 1,2,3 BE Student, mechanical Department, N.B.Navale Sinhagad College Of Engineering,
MODELLING AND ANALYSIS OF TWO WHEELER SUSPENSION SYSTEM
MODELLING AND ANALYSIS OF TWO WHEELER SUSPENSION SYSTEM A. Harshavardhan Reddy 1, G. Rajasekhar Reddy 2, G. Phanindra 3, K. Vijay Kumar 4 1 Asst. Professor, Mechanical, Gurunanak Institutions, Telangana,
Static Stress Analysis of Piston
Static Stress Analysis of Piston Kevin Agrawal B. E. Student, Mechanical Engineering, BITS Pilani K. K. Birla Goa Campus. AH7-352, BITS Pilani, K. K. Birla Goa Campus, NH 17B, Zuarinagar 403726. Parva
International Journal of Scientific & Engineering Research Volume 8, Issue 10, October-2017 ISSN
309 Design and Analysis of Suspension System for a Formula Style Car Anshul Kunwar 1, Mohit Nagpal 2, Geetanjali Raghav 3 1 Student, Department of Mechanical Engineering, DIT University, Dehradun-248009
KEYWORDS: - Go-Kart, Steering, Universal Joints, FEA, ANSYS.
DESIGN AND ANALYSIS OF GO-KART STEERING SYSTEM Mr.Jagtap S.T. 1, Mr. G.R. Drshpande 2 Department of Mechanical Engineering, NBNSCOE, Solapur Department of Mechanical Engineering, A.G.P.I.T, Solapur ABSTRACT
Analysis Of Vehicle Air Compressor Mounting Bracket
Analysis Of Vehicle Air Compressor Mounting Bracket Murtaza Goawala 1,Rahul Giri 2,Niket Phalke 3,Krishna Singh 4,Prof. Nitin Sall 5 1,2,3,4,5 Automobile Engineering Dept., Theem College Of Engineering,
STUDY AND ANALYSIS OF TIRE CHANGING MACHINE COMPONENTS
STUDY AND ANALYSIS OF TIRE CHANGING MACHINE COMPONENTS Mr. Sutar Gururaj 1,Mr. Suryawanshi Bhairavnath 2, Mr. Tengle Kiran 3 Mr. Thaware Madan 4 1,2,3,4UG, Mechanical Engineering, UCOER, Pune, Maharashtra,
Design and Analysis of Steering Knuckle Component
Design and Analysis of Steering Knuckle Component Sanjay Yadav 1, Ravi Kumar Mishra 1, Varish Ansari 1, Shyam Bihari Lal 2 1 Student, 2 Assistant Professor, Department of Mechanical Engineering, Buddha
Design and Analysis of Clutch Plate for Automatic Single Plate Clutch
ISSN 2395-1621 Design and Analysis of Clutch Plate for Automatic Single Plate Clutch #1 Ravikiran M. Tate, #2 S. H. Sarje 1 rtate26@gmail.com 2 suhas_sarje7@rediffmail.com #12 Mechanical Department, JSPM
Structural Analysis of Student Formula Race Car Chassis
Structural Analysis of Student Formula Race Car Chassis Arindam Ghosh 1, Rishika Saha 2, Sourav Dhali 3, Adrija Das 4, Prasid Biswas 5, Alok Kumar Dubey 6 1Assistant Professor, Dept. of Mechanical Engineering,
Design and Analysis of 2 - Speed gearbox for Bicycles
Design and Analysis of 2 - Speed gearbox for Bicycles Venu Akhil Kumar Parakala, Lucky Purushwani SMBS, VIT University, Chennai Campus, Vandalur-kelambakam road, Chennai-600127 ABSTRACT This paper sees
Vibration Analysis of an All-Terrain Vehicle
Vibration Analysis of an All-Terrain Vehicle Neeraj Patel, Tarun Gupta B.Tech, Department of Mechanical Engineering, Maulana Azad National Institute of Technology, Bhopal, India. Abstract - Good NVH is
DESIGN, ANALYSIS AND FABRICATION OF BRAKING SYSTEM WITH REAR INBOARD BRAKES IN BAJA ATV
DESIGN, ANALYSIS AND FABRICATION OF BRAKING SYSTEM WITH REAR INBOARD BRAKES IN BAJA ATV Aman Sharma 1, Prakhar Amrute 2, Suryakant Singh Thakur 3, Jatin Shrivastav 4 1,2,3,4Department of Mechanical Engineering,
Static And Modal Analysis of Tractor Power Take Off (PTO) Gearbox Housing
Static And Modal Analysis of Tractor Power Take Off (PTO) Gearbox Housing Gopali S Lamani 1, Prof: S.R.Basavaraddi 2, Assistant Professor, Department of Mechanical Engineering, JSPM NTC RSSOER,India1 Professor,
Design And Development Of Roll Cage For An All-Terrain Vehicle
Design And Development Of Roll Cage For An All-Terrain Vehicle Khelan Chaudhari, Amogh Joshi, Ranjit Kunte, Kushal Nair E-mail : khelanchoudhary@gmail.com, amogh_4291@yahoo.co.in,ranjitkunte@gmail.com,krockon007@gmail.com
Design and Optimization of Suspension System of All Terrain Vehicle
Design and Optimization of Suspension System of All Terrain Vehicle Abhishek Rajput 1, Bhupendra Kasana 2, Dhruv Sharma 3, Chandan B.B 4 1, 2, 3 Under Graduate students, Dept. of Mechanical Engineering,
KINEMATICS OF REAR SUSPENSION SYSTEM FOR A BAJA ALL-TERRAIN VEHICLE.
International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 8, August 2017, pp. 164 171, Article ID: IJMET_08_08_019 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=8&itype=8
Static Structural Analysis & Optimization of Concept Automotive A-Arm Mechanical Engineering Design
Static Structural Analysis & Optimization of Concept Automotive A-Arm Mechanical Engineering Design Ashish R. Pawar 1, Madhuri V. Bodke 2, Aditya R. Wankhade 3 1,3 Mechanical Engineering Department, ABMSP
Design and Vibrational Analysis of Flexible Coupling (Pin-type)
Design and Vibrational Analysis of Flexible Coupling (Pin-type) 1 S.BASKARAN, ARUN.S 1 Assistant professor Department of Mechanical Engineering, KSR Institute for Engineering and Technology, Tiruchengode,
Design, Analysis & Balancing of 5 Cylinder Engine Crankshaft
International OPEN ACCESS Journal Of Modern Engineering Research (IJMER) Design, Analysis & Balancing of 5 Cylinder Engine Crankshaft Yogesh S. Khaladkar 1, Lalit H. Dorik 2, Gaurav M. Mahajan 3, Anil
Study and Analysis of Front Suspension Shackle Bracket for Commercial Vehicle
Study and Analysis of Front Suspension Shackle Bracket for Commercial Vehicle 1 Jadhav Shashikant, 2 Madki S. 1 ME Student, 2 Professor 1 Department of Mechanical 2 Professor Department of Mechanical Engineering,
International Engineering Research Journal Analysis of HCV Chassis using FEA
International Engineering Research Journal Special Edition PGCON-MECH-017 International Engineering Research Journal Nikhil Tidke 1, D. H. Burande 1 PG Student, Mechanical Engineering, Sinhgad College
International Journal of Scientific Research and Modern Education (IJSRME) ISSN (Online): (www.rdmodernresearch.com) Volume I, Issue II,
DESIGN AND ANALYSIS OF CRANKSHAFT FOR 4- STROKE DEISEL ENGINE M. Srihari*, Shaik Himam Saheb** & S. Vijaya Nirmala*** Assistant Professor, Guru Nanak Institute of Technology, Hyderabad, Telangana Abstract:
Design and Optimisation of Roll Cage of a Single Seated ATV
IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-1684,p-ISSN: 2320-334X, Volume 12, Issue 2 Ver. III (Mar - Apr. 2015), PP 56-61 www.iosrjournals.org Design and Optimisation of
ANALYSIS OF EXISTING TROLLEY AXLE USING ANSYS
International Journal of Science, Environment and Technology, Vol. 4, No 2, 2015, 293 299 ISSN 2278-3687 (O) 2277-663X (P) ANALYSIS OF EXISTING TROLLEY AXLE USING ANSYS 1 Mr. Harish V. Katore, 2 Mr. Ashitosh
OPTIMIZATION & ANANLYSIS OF A HEAVY VEHICAL CHASSIS USING COMPOSITE MATERIALS
OPTIMIZATION & ANANLYSIS OF A HEAVY VEHICAL CHASSIS USING COMPOSITE MATERIALS U.NANDINI 1, C.PARIMALA 2, K.SAI KEERTHI 3 1,2,3 Assist. professor, department of mechanical engineering, Anantha Lakshmi Institute
Effect of Tyre Overload and Inflation Pressure on Rolling Loss (resistance) and Fuel Consumption of Automobile Cars
ISSN (e): 2250 3005 Vol, 04 Issue, 10 October 2014 International Journal of Computational Engineering Research (IJCER) Effect of Tyre Overload and Inflation Pressure on Rolling Loss (resistance) and Fuel
THERMAL ANALYSIS OF PISTON BLOCK USING FINITE ELEMENT ANALYSIS
THERMAL ANALYSIS OF PISTON BLOCK USING FINITE ELEMENT ANALYSIS Pushpandra Kumar Patel 1, Vikky Kumhar 2 1 BE Student, 2 Assistant Professor Department of Mechanical Engineering, SSTC-SSGI, Junwani, Bhilai,
Stress and Design Analysis of Triple Reduction Gearbox Casing
IJIRST International Journal for Innovative Research in Science & Technology Volume 2 Issue 02 July 2015 ISSN (online): 2349-6010 Stress and Design Analysis of Triple Reduction Gearbox Casing Mitesh Patel
Thermal Analysis of Helical and Spiral Gear Train
International Journal for Ignited Minds (IJIMIINDS) Thermal Analysis of Helical and Spiral Gear Train Dr. D V Ghewade a, S S Nagarale b & A N Pandav c a Principal, Department of Mechanical, GENESIS, Top-Kolhapur,
Address for Correspondence
Research Article DESIGN AND STRUCTURAL ANALYSIS OF DIFFERENTIAL GEAR BOX AT DIFFERENT LOADS C.Veeranjaneyulu 1, U. Hari Babu 2 Address for Correspondence 1 PG Student, 2 Professor Department of Mechanical
DESIGN AND ANALYSIS OF LEAF SPRING FOR SOLAR VEHICLE
DESIGN AND ANALYSIS OF LEAF SPRING FOR SOLAR VEHICLE MAY MYA DARLI CHO, HTAY HTAY WIN, 3 AUNG KO LATT,,3 Department of Mechanical Engineering, Mandalay Technological University, Mandalay, Myanmar E-mail:
DESIGN AND DEVELOPMENT OF IC ENGINE GO-KART
DESIGN AND DEVELOPMENT OF IC ENGINE GO-KART AkshayB. Khot 1, KunalJ. Mahekar 2, VaibhavJ. Mahekar 3, GurunathS. Patil 4, MohanishM. Patil 5, Prof. S. P. Jarag 6 BE Student, Department of Mechanical Engineering,
DESIGNING AND ANALYSING STAIR CASE LIFT SYSTEM
DESIGNING AND ANALYSING STAIR CASE LIFT SYSTEM Timur Choban Khidir 1, Abbas Mohammed Ismael 2 & Ayaz Aydin Abduljabbar 3 1, 2, 3 Kirkuk University / College of Engineering - Mechanical Department, IRAQ
Fatigue life evaluation of an Automobile Front axle
Fatigue life evaluation of an Automobile Front axle Prathapa.A.P (1), N. G.S. Udupa (2) 1 M.Tech Student, Mechanical Engineering, Nagarjuna College of Engineering and Technology, Bangalore, India. e-mail:
Structural performance improvement of passenger seat using FEA for AIS 023 compliance
Structural performance improvement of passenger seat using FEA for AIS 023 compliance 1 Satyajit Thane, 2 Dr.R.N.Patil, 3 Chandrakant Inamdar 1 P.G.Student, 2 Prof. & Head, 3 Director 1 Department of Mechanical
Design and Analysis of Six Speed Gear Box
Design and Analysis of Six Speed Gear Box Ujjayan Majumdar 1, Sujit Maity 2, Gora Chand Chell 3 1,2 Student, Department of Mechanical Engineering, Jalpaiguri Government Engineering College, Jalpaiguri,
Design and Analysis of Pressure Die Casting Die for Side Differential Cover of Mini truck
Design and Analysis of Pressure Die Casting Die for Side Differential Cover of Mini truck 1 A Chakravarthi P.G student, Department of Mechanical Engineering,KSRM CE, kadapa-516003 2. R Rama Krishna Reddy,
FINITE ELEMENT ANALYSIS OF CONNECTING ROD USING ANSYS
FINITE ELEMENT ANALYSIS OF CONNECTING ROD USING ANSYS 1 NIKHIL U.THAKARE, 2 NITIN D. BHUSALE, 3 RAHUL P.SHINDE, 4 MAHESH M.PATIL 1,3,4 B.E., Babasaheb Naik College of Engineering, Pusad, Maharashtra, India,
Design, Static and Dynamic analysis of an All- Terrain Vehicle Chassis and Suspension System
Design, Static and Dynamic analysis of an All- Terrain Vehicle Chassis and Suspension System 1 Mr. Dibya Narayan Behera, 2 Rajesh Kumar, 3 Kunal Abhishek, 4 Sunil Kumar Panda 1 Asst. Professor, 2 Under
EVALUATION ON FAILURE OF AN AUTOMOBILE DRIVE SHAFT
EVALUATION ON FAILURE OF AN AUTOMOBILE DRIVE SHAFT International Journal of Latest Trends in Engineering and Technology Vol.(8)Issue(3), pp.059-067 DOI: http://dx.doi.org/10.21172/1.83.008 e-issn:2278-621x
DESIGN OF CHASSIS OF STUDENT FORMULA RACE CAR
DESIGN OF CHASSIS OF STUDENT FORMULA RACE CAR Shubhanandan Dubey 1, Rahul Jaiswal 2, Raunak Mishra 3 1, 2, 3 Department of Automobile, Theem College of Engineering, University of Mumbai, Maharashtra, India
SIX-BAR STEERING MECHANISM
SIX-BAR STEERING MECHANISM Shrey Lende 1 1 UG Student, Department of Mech, G.H Raisoni College of Engineering, Nagpur, RTMN University ABSTRACT In this paper a steering system is designed for a Low weight
Composite Long Shaft Coupling Design for Cooling Towers
Composite Long Shaft Coupling Design for Cooling Towers Junwoo Bae 1,#, JongHun Kang 2, HyoungWoo Lee 2, Seungkeun Jeong 1 and SooKeun Park 3,* 1 JAC Coupling Co., Ltd., Busan, South Korea. 2 Department
Static Analysis of Crankcase and Crankshaft of Single Cylinder Four Stroke Diesel Engine
Static Analysis of Crankcase and Crankshaft of Single Cylinder Four Stroke Diesel Engine Kakade Pratik 1 Post Graduate Student kakadepratik@gmail.com Pasarkar M. D. 2 Assistant Professor mdpasarkar@gmail.com
Design and Stress Analysis of Crankshaft for Single Cylinder 4-Stroke Diesel Engine
Design and Stress Analysis of Crankshaft for Single Cylinder 4-Stroke Diesel Engine Amit Solanki #1, Jaydeepsinh Dodiya #2, # Mechanical Engg.Deptt, C.U.Shah University, Wadhwan city, Gujarat, INDIA Abstract
Simulation and Analysis of Vehicle Suspension System for Different Road Profile
Simulation and Analysis of Vehicle Suspension System for Different Road Profile P.Senthil kumar 1 K.Sivakumar 2 R.Kalidas 3 1 Assistant professor, 2 Professor & Head, 3 Student Department of Mechanical
DESIGN AND ANALYSIS OF REAR WHEEL HUB & STEERING KNUCKLE
DESIGN AND ANALYSIS OF REAR WHEEL HUB & STEERING KNUCKLE Vivek Dhameliya 1, Nishant Sheta 2 B.E Student Department of Mechanical Engineering Marwadi Education Foundation Group of Institute Rajkot, India
Analysis of Multistage Linkage Based Eclipse Gearbox for Wind Mill Applications
Analysis of Multistage Linkage Based Eclipse Gearbox for Wind Mill Applications 1 Shrutika Patil, 2 J. G. Patil, 3 R. Y. Patil 1 M.E. Student, 2 Associate Professor, 3 Head of Department, Department of
Copy Right to GARPH Page 1
DESIGN AND ASSEMBLY OF 4 CYLINDER ENGINE COMPONENTS WITH ITS THERMAL AND STRESS ANALYSIS 1 M. M. KASOD PG Student, Pankaj Laddhad Institute of Technology & Management Studies, Buldana, India mmkasod@rediffmail.com
M.E. Scholar (Design and Thermal), I.E.T-DAVV, Indore, M.P., India. 2
IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY PARAMETRIC ANALYSIS OF SPUR GEAR TO DETERMINE THE EFFECT OF VARIATION OF R.P.M. AND PRESSURE ANGLE ON STRESS PRODUCED Yogendra
Chapter 2 Analysis on Lock Problem in Frontal Collision for Mini Vehicle
Chapter 2 Analysis on Lock Problem in Frontal Collision for Mini Vehicle Ce Song, Hong Zang and Jingru Bao Abstract To study the lock problem in the frontal collision test on a kind of mini vehicle s sliding
STRESS ANALYSIS OF STEERING OF A FIGHTER AIRCRAFT
STRESS ANALYSIS OF STEERING OF A FIGHTER AIRCRAFT BEERAPPA School of Mechanical Engineering REVA University, Bangalore beerappa4rcr@gmail.com K.S. NARAYANASWAMY Senior Assistant Professor REVA University,
Chapter 7: Thermal Study of Transmission Gearbox
Chapter 7: Thermal Study of Transmission Gearbox 7.1 Introduction The main objective of this chapter is to investigate the performance of automobile transmission gearbox under the influence of load, rotational
Finite element analysis of Spiral bevel gears pair used in an Automobile Differential gear box
International Journal of Advances in Scientific Research and Engineering (ijasre) E-ISSN : 2454-8006 Vol.3, Special Issue 1 Aug - 2017 Finite element analysis of Spiral bevel gears pair used in an Automobile
IJESRT. Scientific Journal Impact Factor: (ISRA), Impact Factor: 2.114
IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY SIMULATION AND VIBRATION ANALYSIS OF GEAR BOX USED IN COOLING TOWER FAN K.G.Patel*, S.U.Patil, H.G.Patil D.N.Patel College of
Load Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4 Stroke Engine
IJSRD - International Journal for Scientific Research & Development Vol. 3, Issue 08, 2015 ISSN (online): 2321-0613 Load Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4
Racing Tires in Formula SAE Suspension Development
The University of Western Ontario Department of Mechanical and Materials Engineering MME419 Mechanical Engineering Project MME499 Mechanical Engineering Design (Industrial) Racing Tires in Formula SAE
DESIGN AND ANALYSIS OF EXHAUST VALVE SPRINGS IN IC ENGINES
DESIGN AND ANALYSIS OF EXHAUST VALVE SPRINGS IN IC ENGINES Gowtham.R 1*, Sangeetha N 2 1 Third year UG student, Department of Mechanical Engineering, Kumaraguru College of Engineering and Technology, Coimbatore,
COMPARISON OF ANALYTICAL & FEA OF CONTACT ANALYSIS OF SPUR GEAR DRIVE
COMPARISON OF ANALYTICAL & FEA OF CONTACT ANALYSIS OF SPUR GEAR DRIVE Sachin Almelkar 1, Prof I.G.Bhavi 2 1M.Tech (Machine Design). B L D E A s Dr.P.G. Halakatti College Of Engineering and Technology,Vijayapur,
VEHICLE ANTI-ROLL BAR ANALYZED USING FEA TOOL ANSYS
VEHICLE ANTI-ROLL BAR ANALYZED USING FEA TOOL ANSYS P. M. Bora 1, Dr. P. K. Sharma 2 1 M. Tech. Student,NIIST, Bhopal(India) 2 Professor & HOD,NIIST, Bhopal(India) ABSTRACT The aim of this paper is to
ISSN: [ICEMESM-18] Impact Factor: 5.164
![ISSN: [ICEMESM-18] Impact Factor: 5.164](/thumbs/96/128311980.jpg "ISSN: [ICEMESM-18] Impact Factor: 5.164")
IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY FAILURE ANALYSIS OF COUPLER SCREW IN NARROW GAUGE RAILWAYS Mr Tejpal Parshiwanikar Dept of Mechanical Engineering, GHRAET, Nagpur
ISSN: [Mukherjee * et al., 6(9): September, 2017] Impact Factor: 4.116
![ISSN: [Mukherjee * et al., 6(9): September, 2017] Impact Factor: 4.116](/thumbs/82/86563818.jpg "ISSN: [Mukherjee * et al., 6(9): September, 2017] Impact Factor: 4.116")
IC Value:.00 IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY DESIGN AND ANALYSIS OF POWER TRAIN SYSTEM OF HEAVY TRUCK ENGINE Sabyasachi Mukherjee* & Puspendu Chandra Assistant
SAE Baja: Project Proposal Suspension and Steering
SAE Baja: Project Proposal Suspension and Steering Benjamin Bastidos, Victor Cabilan, Jeramie Goodwin, William Mitchell, Eli Wexler Wednesday, November 20, 2013 Overview Introduction Concept Generation
COMPARATIVE ANALYSIS OF CRANKSHAFT IN SINGLE CYLINDER PETROL ENGINE CRANKSHAFT BY NUMERICAL AND ANALYTICAL METHOD
COMPARATIVE ANALYSIS OF CRANKSHAFT IN SINGLE CYLINDER PETROL ENGINE CRANKSHAFT BY NUMERICAL AND ANALYTICAL METHOD Mr. Anant B. Khandkule PG Student Mechanical Engineering Department, Sinhgad Institute
International Journal of Modern Trends in Engineering and Research e-issn No.: , Date: April, 2016
International Journal of Modern Trends in Engineering and Research www.ijmter.com e-issn No.:2349-9745, Date: 28-30 April, 2016 Design of Head Light Moving Mechanism With Steering Mangesh A. Jadhav1,Tushar
Design and Analysis of New Locking Mechanism For Fixing Wheels To An Automobile with minimum Human effort
Design and Analysis of New Locking Mechanism For Fixing Wheels To An Automobile with minimum Human effort K Balaji 1, V Anand Kumar 2 P.G. Student, Department of Mechanical Engineering, VNR VJIET Engineering
Design, Analysis and Mockup of Semi-Trailing Rear Suspension for an All-Terrain Vehicle (ATV)
Design, Analysis and Mockup of Semi-Trailing Rear Suspension for an All-Terrain Vehicle (ATV) Kushagra Garg 1 Undergraduate Student, School of Mechanical Engineering, KIIT University, Odisha, India 1 ABSTRACT: