Design and Analysis of Pressure Die Casting Die for Side Differential Cover of Mini truck

Size: px
Start display at page:

Download "Design and Analysis of Pressure Die Casting Die for Side Differential Cover of Mini truck"

Transcription

1 Design and Analysis of Pressure Die Casting Die for Side Differential Cover of Mini truck 1 A Chakravarthi P.G student, Department of Mechanical Engineering,KSRM CE, kadapa R Rama Krishna Reddy, M.Tech,Associate Professor Department of Mechanical Engineering,KSRM CE, kadapa ABSTARCT The design of die-casting dies requires considerable skill and expertise based on experience. The designer proposes designs of dies employed to cast parts from various alloys, and perform a variety of other operations. Every new job requires original thought in its design and the solving of individual problems in its manufacture. The objective here is to design dies to be fit for the purpose, operate at optimum shot rate and is of reasonably simple construction. The main purpose of this report is to present the systematic design procedure for pressure die-casting dies. Die-casting dies like any other type of tooling can be very simple or very complex. How difficult they are to design and build depends entirely on the parts they produce. The function of these SIDE DIFFERENTIAL COVER (part of gear box casing) is to protect and guide the gears used in power transmission. In this casing, power transmission is done by regulating the speed of driving wheels through crank shaft to rear axle. In this project we are also conducting static structural analysis for validating the design. Software used for analysis is Ansys. Keywords: Side Differential Cover; Core and Cavity Dies; Pro-Engineering; Ansys Introduction to Differential Cover: Gears are used as independent units to reduce or increase the input speed. The unit is enclosed in rigid closed housings (called casing) which supports the shafts, hold lubricant inside casing, and protect the gears from dust and moisture. Also the housing provides necessary cooling surfaces to dissipate the heat generated during operation. When the unit is used to get only one reduced output speed for a given input speed then it is called a SPEED REDUCER, while for one input speed more than one output speeds are obtained, then the unit is called a GEAR BOX. Gear box is widely used for reduction of speed in automobiles. Metal Minimum section Minimum draft Aluminum alloys 0.89 mm (0.035 in) 1:100 (0.6 ) Brass and bronze 1.27 mm (0.050 in) 1:80 (0.7 ) Magnesium alloys 1.27 mm (0.050 in) 1:100 (0.6 ) Zinc alloys 0.63 mm (0.025 in) 1:200 (0.3 ) Methodology: A Geometric model is representing the Side differentialcover. The geometrical modeling of the Side differential cover is carried out Cad-Software Pro-E Which is Capable of producing precise Solid and surface Geometry. After modeling in pro-eit was then covered into <.step or IGES formate>, the imported to Cosmosworks. By considering meshing Parameters required for proper mesh automatic meshing is done in cosmosworks. Available online: P a g e 473

2 After modeling in pro-e it was then converted into <.step or IGES format>, then imported to cosmosworks. FUNCTION OF SIDE DIFFERENTIAL COVER The function of these SIDE DIFFERENTIAL COVER (part of gear box casing) is to protect and guide the gears used in power transmission. In this casing, power transmission is done by regulating the speed of driving wheels through crank shaft to rear axle. The material used in making the Gear box casing is Aluminum alloy Grade LM24. Using this alloy, casting for gear box casing is made which is used in most of the automobiles such as motor bikes, passenger cars and passenger auto s etc. The engine capacity of the Mini truck is 26 BHP/19.2 KW and Speed of the engine is 3600R.P.M. Aluminum alloy Grade LM24 is used due to its following characteristics: 1) Good thermal conductivity (Heat conducting capacity) 2) Excellent Fluidity, 3) Good resistant to corrosion, 4) Suitable for intricate castings, 5) Good weld ability, 6) Electrical conductivity. Main Aim of the Project: Objective of this project work is to model the side differential cover of gear box casing using Pro/Engineer Wild fire 5.0 software and perform structural analysis. Side engine cover of Gear box casing taken up for modeling is used in mini trucks. feature is individually described then integrated into the part. The other significant aspect of conventional drafting is that the part geometry is defined by the drawing. If it is desired to change the size, shape, or location of a feature, the physical lines on the drawing must be changed (in each affected view) then associated dimensions are updated. When using parametric modeling, the features are driven by the dimensions (parameters). Steps Followed in the Project: Pro/ENGINEER is a feature based, parametric solid modeling program. As such as significantly different from conventional drafting programs. In conventional drafting (either manual or computer assisted), various views of a part are created in an attempt to describe the geometry. Each view incorporates aspects of various features (surfaces, cuts, radii, holes, protrusions) but the features are not individually defined. In feature based modeling, each Available online: P a g e 474

3 STATIC ANALYSIS OF SIDE DIFFERENTIAL COVER The Basic concept in FEA is that the body or structure may be divided into smaller elements of finite dimensions called Finite Elements. The original body or the structure is then considered as an assemblage of these elements connected at a finite number of joints called Nodes or Nodal Points. Simple functions are chosen to approximate the displacements over each finite element. Such assumed functions are called shape functions. This will represent the displacement with in the element in terms of the displacement at the nodes of the element. Poisson's 0.33 ratio: Mass 2710 density: kg/m^3 Shear 2.69e+010 modulus: Thermal 2.16e-005 expansion /Kelvin coefficient: Static Analysis of Stress, Strain and Displacement of No Load condition. Name: Model type: Default failure criterion: Yield strength: Tensile strength: Elastic modulus: LM24 Linear Elastic Isotropic Max von Mises Stress 4.35e e e+010 Available online: P a g e 475

4 Static Analysis of Stress, Strain and Displacement of 7 Persons Load condition. Static Analysis of Stress, Strain and Displacement of 10 Persons Load condition. Available online: P a g e 476

5 RESULTS TABLE STRESS (N/mm 2 ) DISPLACEME NT (mm) STRAIN VEHICL E WEIGHT VEHICLE WEIGHT +7 PERSONS VEHICLE WEIGHT+ 10 PERSONS [6] Injectionmould design: R.G.W. PYE (East- West press Pvt. Ltd), Edition2000 pp-2 Conclusion: We have done structural analysis on the side differential cover by applying the loads of only vehicle weight, vehicle weight+ 7 persons weight and vehicle weight + 10 persons weight to validate the strength using material Aluminum alloy LM24. By observing the analysis results, the analyzed stress values are less than the respective yield stress value under all load conditions. So using LM 24 for side differential cover is safe. Apart from the above mentioned projects, we have done the assembly, detailing and designing of feed system for other castings. This gave me a good exposure to die casting. From these it can be concluded that the scope of the project is fully justified in this project. In this thesis we are going to conclude that this project fulfills the all the requirements of the side differential cover design and manufacturing. Reference: [1] Machine design, T.V.Sundararajamoorthy (Anuradha agencies),edition: 2006, gear box pp [2] Machine design, R.S.Khurmi/J.K.Guptha (S.CHAND), Bearing edition2008, pp-962 [3] Design data book:p.s.g.college of Technology (Kalaikathirachchagam), Aluminum Properties edition: 2007 [4] www. google.com online aluminum Gr: LM24 composition and LM6 composition [5] Design of machine element:v.b.bandari (TATA McGraw-hill), edition-2002 pp-58 Available online: P a g e 477

Static Structural and Thermal Analysis of Aluminum Alloy Piston For Design Optimization Using FEA Kashyap Vyas 1 Milan Pandya 2

Static Structural and Thermal Analysis of Aluminum Alloy Piston For Design Optimization Using FEA Kashyap Vyas 1 Milan Pandya 2 IJSRD - International Journal for Scientific Research & Development Vol. 2, Issue 03, 2014 ISSN (online): 2321-0613 Static Structural and Thermal Analysis of Aluminum Alloy Piston For Design Optimization

More information

Load Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4 Stroke Engine

Load Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4 Stroke Engine IJSRD - International Journal for Scientific Research & Development Vol. 3, Issue 08, 2015 ISSN (online): 2321-0613 Load Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4

More information

Design and analysis of shock absorber using FEA tool

Design and analysis of shock absorber using FEA tool International Journal of Engineering Research and Development e-issn: 2278-067X, p-issn: 2278-800X, www.ijerd.com Volume 10, Issue 2 (February 2014), PP.22-28 Design and analysis of shock absorber using

More information

Static Stress Analysis of Piston

Static Stress Analysis of Piston Static Stress Analysis of Piston Kevin Agrawal B. E. Student, Mechanical Engineering, BITS Pilani K. K. Birla Goa Campus. AH7-352, BITS Pilani, K. K. Birla Goa Campus, NH 17B, Zuarinagar 403726. Parva

More information

Stress Analysis of Piston at Different Pressure Load

Stress Analysis of Piston at Different Pressure Load Stress Analysis of Piston at Different Pressure Load 1 PG Student, Department of Mechanical Engineering, SKNSITS, Lonavala, India 2 Professor, Department of Mechanical Engineering, SKNSITS, Lonavala, India

More information

Keywords: Von Mises, Piston, Thermal Analysis, Pressure, CATIAV5R20, ANSYS14 I. INTRODUCTION

Keywords: Von Mises, Piston, Thermal Analysis, Pressure, CATIAV5R20, ANSYS14 I. INTRODUCTION Finite Element Analysis of IC Engine Piston Using Thermo Mechanical Approach 1 S.Sathishkumar, Dr.M.Kannan and 3 V.Raguraman, 1 PG Scholar, Professor, 3 Assistant professor, 1,,3 Department of Mechanical

More information

Structural Analysis of a Ceramic Coated Diesel Engine Piston Using Finite Element Method

Structural Analysis of a Ceramic Coated Diesel Engine Piston Using Finite Element Method Structural Analysis of a Ceramic Coated Diesel Engine Piston Using Finite Element Method 1 Narsaiyolla Naresh, (M.Tech), 2 P.Sampath Rao, M.Tech; (PhD) Mechanical Dept, VREC, Nizamabad- 503003 Abstract:

More information

EFFECT OF TYRE OVERLOAD AND INFLATION PRESSURE ON ROLLING LOSS & FUEL CONSUMPTION OF AUTOMOBILES CARS

EFFECT OF TYRE OVERLOAD AND INFLATION PRESSURE ON ROLLING LOSS & FUEL CONSUMPTION OF AUTOMOBILES CARS EFFECT OF TYRE OVERLOAD AND INFLATION PRESSURE ON ROLLING LOSS & FUEL CONSUMPTION OF AUTOMOBILES CARS D.MADHUSUDHANA 1 C. NAGARAJA 2 PG Student Assistant Professor Dept. of Mechanical Engineering Dept.

More information

Structural Analysis of Differential Gearbox

Structural Analysis of Differential Gearbox Structural Analysis of Differential Gearbox Daniel Das.A Seenivasan.S Assistant Professor Karthick.S Assistant Professor Abstract- The main aim of this paper is to focus on the mechanical design and analysis

More information

Stress and Design Analysis of Triple Reduction Gearbox Casing

Stress and Design Analysis of Triple Reduction Gearbox Casing IJIRST International Journal for Innovative Research in Science & Technology Volume 2 Issue 02 July 2015 ISSN (online): 2349-6010 Stress and Design Analysis of Triple Reduction Gearbox Casing Mitesh Patel

More information

M.E. Scholar (Design and Thermal), I.E.T-DAVV, Indore, M.P., India. 2

M.E. Scholar (Design and Thermal), I.E.T-DAVV, Indore, M.P., India. 2 IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY PARAMETRIC ANALYSIS OF SPUR GEAR TO DETERMINE THE EFFECT OF VARIATION OF R.P.M. AND PRESSURE ANGLE ON STRESS PRODUCED Yogendra

More information

IJESRT. Scientific Journal Impact Factor: (ISRA), Impact Factor: 1.852

IJESRT. Scientific Journal Impact Factor: (ISRA), Impact Factor: 1.852 IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY Design Analysis and Optimization of Piston and Determination of its Thermal Stresses Using CAE Tools Deovrat Vibhandik *1, Ameya

More information

International Journal of Scientific & Engineering Research, Volume 7, Issue 3, March ISSN DESIGN AND ANALYSIS OF A SHOCK ABSORBER

International Journal of Scientific & Engineering Research, Volume 7, Issue 3, March ISSN DESIGN AND ANALYSIS OF A SHOCK ABSORBER International Journal of Scientific & Engineering Research, Volume 7, Issue 3, March-2016 19 DESIGN AND ANALYSIS OF A SHOCK ABSORBER Johnson*, Davis Jose, Anthony Tony Abstract: -Shock absorbers are a

More information

Finite Element Modeling and Analysis of Vehicle Space Frame with Experimental Validation

Finite Element Modeling and Analysis of Vehicle Space Frame with Experimental Validation Finite Element Modeling and Analysis of Vehicle Space Frame with Experimental Validation Assoc. Prof Dr. Mohammed A.Elhaddad Mechanical Engineering Department Higher Technological Institute, Town of 6

More information

Modal analysis of Truck Chassis Frame IJSER

Modal analysis of Truck Chassis Frame IJSER Modal analysis of Truck Chassis Frame 158 Shubham Bhise 1, Vaibhav Dabhade 1, Sujit Pagi 1, Apurvi Veldandi 1. 1 B.E. Student, Dept. of Automobile Engineering, Saraswati College of Engineering, Navi Mumbai,

More information

STATIC STRUCTURAL ANALYSIS AND OPTIMIZATION OF BRAKE PEDAL

STATIC STRUCTURAL ANALYSIS AND OPTIMIZATION OF BRAKE PEDAL STATIC STRUCTURAL ANALYSIS AND OPTIMIZATION OF BRAKE PEDAL Miss. ASHWINI N.GAWANDE 1, Prof.G.E.KONDHALKAR 2, Prof. ASHISH R.PAWAR 3 1PG Student, Design Engineering, APCOE & R, Parvati, Pune 2HOD, Mechanical

More information

International Engineering Research Journal Analysis of HCV Chassis using FEA

International Engineering Research Journal Analysis of HCV Chassis using FEA International Engineering Research Journal Special Edition PGCON-MECH-017 International Engineering Research Journal Nikhil Tidke 1, D. H. Burande 1 PG Student, Mechanical Engineering, Sinhgad College

More information

STRESS ANALYSIS OF PISTON USING PRESSURE LOAD AND THERMAL LOAD

STRESS ANALYSIS OF PISTON USING PRESSURE LOAD AND THERMAL LOAD STRESS ANALYSIS OF PISTON USING PRESSURE LOAD AND THERMAL LOAD Vaishali R. Nimbarte 1, Prof. S.D. Khamankar 2 1 Student of M.Tech (CAD/CAM), Rajiv Gandhi College Of Engineering, Research and Technology,

More information

FEM Analysis of Combined Paired Effect on Piston & Connecting Rod using ANSYS

FEM Analysis of Combined Paired Effect on Piston & Connecting Rod using ANSYS FEM Analysis of Combined Paired Effect on Piston & Connecting Rod using ANSYS Kunal Saurabh Assistant Professor, Mechanical Department IEC Group of Institutions, Greater Noida - India kunalsaurabh.me@ieccollege.com

More information

Chapter 7: Thermal Study of Transmission Gearbox

Chapter 7: Thermal Study of Transmission Gearbox Chapter 7: Thermal Study of Transmission Gearbox 7.1 Introduction The main objective of this chapter is to investigate the performance of automobile transmission gearbox under the influence of load, rotational

More information

DESIGN OPTIMIZATION AND FINITE ELEMENT ANALYSIS OF PISTON USING PRO-e

DESIGN OPTIMIZATION AND FINITE ELEMENT ANALYSIS OF PISTON USING PRO-e Int. J. Mech. Eng. & Rob. Res. 2014 Rohit Tamrakar et al., 2014 Research Paper ISSN 2278 0149 www.ijmerr.com Vol. 3, No. 2, April 2014 2014 IJMERR. All Rights Reserved DESIGN OPTIMIZATION AND FINITE ELEMENT

More information

Design, Analysis& Optimization of Truck chassis- Rail & Cross member

Design, Analysis& Optimization of Truck chassis- Rail & Cross member Design, Analysis& Optimization of Truck chassis- Rail & Cross member Mr. Jinto Joju Thaikkattil 1, Gayatri Patil 2 1 PGScholar, Department of Mechanical Engg., KJCOEMR, Pune, jjt7171@gmail.com 2 Assistant

More information

INTERNATIONAL JOURNAL OF PURE AND APPLIED RESEARCH IN ENGINEERING AND TECHNOLOGY

INTERNATIONAL JOURNAL OF PURE AND APPLIED RESEARCH IN ENGINEERING AND TECHNOLOGY INTERNATIONAL JOURNAL OF PURE AND APPLIED RESEARCH IN ENGINEERING AND TECHNOLOGY A PATH FOR HORIZING YOUR INNOVATIVE WORK DESIGN, ANALYSIS AND OPTIMIZATION OF PISTON OF 180CC ENGINE USING CAE TOOLS NIKHIL

More information

Fatigue Life Estimation of Chassis Frame FESM Bracket for Commercial Vehicle

Fatigue Life Estimation of Chassis Frame FESM Bracket for Commercial Vehicle Fatigue Life Estimation of Chassis Frame FESM Bracket for Commercial Vehicle Shivakumar M.M 1, Nirmala L 2 ¹M-Tech Student, Dept. of Mechanical Engineering,K.S Institute of Technology, Bangalore, India

More information

Optimization of Four Cylinder Engine Crankshaft using FEA

Optimization of Four Cylinder Engine Crankshaft using FEA Optimization of Four Cylinder Engine Crankshaft using FEA Prasad P. Gaware 1, Prof. V.S. Aher 2 Department of Mechanical Engineering, AVCOE, Sangamner 1 Department of Mechanical Engineering, AVCOE, Sangamner

More information

ANALYSIS OF SURFACE CONTACT STRESS FOR A SPUR GEAR OF MATERIAL STEEL 15NI2CR1MO28

ANALYSIS OF SURFACE CONTACT STRESS FOR A SPUR GEAR OF MATERIAL STEEL 15NI2CR1MO28 ANALYSIS OF SURFACE CONTACT STRESS FOR A SPUR GEAR OF MATERIAL STEEL 15NI2CR1MO28 D. S. Balaji, S. Prabhakaran and J. Harish Kumar Department of Mechanical Engineering, Chennai, India E-Mail: balajimailer@gmail.com

More information

DESIGN AND ANALYSIS OF SHOCK ABSORBER

DESIGN AND ANALYSIS OF SHOCK ABSORBER DESIGN AND ANALYSIS OF SHOCK ABSORBER 1 A. Chinnamahammad bhasha, 2 N. Vijay rami reddy, 3 B. Rajnaveen 1 M.Tech Student, Dept of ME, Vignan University, India. 23Asst proof, Dept of ME, Mahatma Gandhi

More information

Structural Analysis of Pick-Up Truck Chassis using Fem

Structural Analysis of Pick-Up Truck Chassis using Fem International Journal of ChemTech Research CODEN (USA): IJCRGG, ISSN: 0974-4290, ISSN(Online):2455-9555 Vol.9, No.06 pp 384-391, 2016 Structural Analysis of Pick-Up Truck Chassis using Fem Rahul.V 1 *,

More information

ISSN: [Raghunandan* et al., 5(11): November, 2016] Impact Factor: 4.116

ISSN: [Raghunandan* et al., 5(11): November, 2016] Impact Factor: 4.116 IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY DESIGN AND ANALYSIS OF GO-KART CHASSIS D.Raghunandan*, A.Pandiyan, Shajin Majeed * Mechanical Department, Final year, Saveetha

More information

Redesign and Analysis of Automobile Wheel Rim #1 Pandit Shailesh, #2 Gajjal Shekhar

Redesign and Analysis of Automobile Wheel Rim #1 Pandit Shailesh, #2 Gajjal Shekhar ISSN 2395-1621 Redesign and Analysis of Automobile Wheel Rim #1 Pandit Shailesh, #2 Gajjal Shekhar 1 shailesh27290@gmail.com 2 shekhar.gajjal@sinhgad.edu #1234 Department of Mechanical Engineering,SavitribaiPhule

More information

Design and Analysis of Front Lower Control Arm by Using Topology Optimization

Design and Analysis of Front Lower Control Arm by Using Topology Optimization Design and Analysis of Front Lower Control Arm by Using Topology Optimization Prashant Gunjan 1, Amit Sarda 2 12 Department of Mechanical Engineering, Christian College of Engineering and Technology, Bhilai

More information

Design Evaluation and Optimization of a Disc Brake

Design Evaluation and Optimization of a Disc Brake Design Evaluation and Optimization of a Disc Brake Abstract: Susmitha Sankatala M.Tech (Production), Department of Mechanical Engineering, Sree Vaanmayi Institute of Engineering & Technology. The disc

More information

Design and Vibrational Analysis of Flexible Coupling (Pin-type)

Design and Vibrational Analysis of Flexible Coupling (Pin-type) Design and Vibrational Analysis of Flexible Coupling (Pin-type) 1 S.BASKARAN, ARUN.S 1 Assistant professor Department of Mechanical Engineering, KSR Institute for Engineering and Technology, Tiruchengode,

More information

[Vishal*et al., 5(7): July, 2016] ISSN: IC Value: 3.00 Impact Factor: 4.116

[Vishal*et al., 5(7): July, 2016] ISSN: IC Value: 3.00 Impact Factor: 4.116 IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY DESIGN AND ANALYSIS OF ALUMINUM ALLOY PISTON USING CAE TOOLS Mr. Jadhav Vishal, Dr. R.K. Jain, Mr. Yogendra S.Chauhan *M-Tech

More information

Design and Analysis of Go-kart Chassis

Design and Analysis of Go-kart Chassis Design and Analysis of Go-kart Chassis Sannake Aniket S. 1, Shaikh Sameer R. 2, Khandare Shubham A. 3 Prof. S.A.Nehatrao 4 1,2,3 BE Student, mechanical Department, N.B.Navale Sinhagad College Of Engineering,

More information

Design and Analysis of New Locking Mechanism For Fixing Wheels To An Automobile with minimum Human effort

Design and Analysis of New Locking Mechanism For Fixing Wheels To An Automobile with minimum Human effort Design and Analysis of New Locking Mechanism For Fixing Wheels To An Automobile with minimum Human effort K Balaji 1, V Anand Kumar 2 P.G. Student, Department of Mechanical Engineering, VNR VJIET Engineering

More information

Stress Analysis of Engine Camshaft and Choosing Best Manufacturing Material

Stress Analysis of Engine Camshaft and Choosing Best Manufacturing Material Stress Analysis of Engine Camshaft and Choosing Best Manufacturing Material Samta Jain, Mr. Vikas Bansal Rajasthan Technical University, Kota (Rajasathan), India Abstract This paper presents the modeling

More information

Modeling and Analysis of Tractor Trolley Axle Using Ansys

Modeling and Analysis of Tractor Trolley Axle Using Ansys IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-1684,p-ISSN: 2320-334X, Volume 6, Issue 5 (May. - Jun. 2013), PP 88-92 Modeling and Analysis of Tractor Trolley Axle Using Ansys

More information

Design and Analysis of Steering Knuckle Component

Design and Analysis of Steering Knuckle Component Design and Analysis of Steering Knuckle Component Sanjay Yadav 1, Ravi Kumar Mishra 1, Varish Ansari 1, Shyam Bihari Lal 2 1 Student, 2 Assistant Professor, Department of Mechanical Engineering, Buddha

More information

Copy Right to GARPH Page 1

Copy Right to GARPH Page 1 DESIGN AND ASSEMBLY OF 4 CYLINDER ENGINE COMPONENTS WITH ITS THERMAL AND STRESS ANALYSIS 1 M. M. KASOD PG Student, Pankaj Laddhad Institute of Technology & Management Studies, Buldana, India mmkasod@rediffmail.com

More information

Design and Simulation of Go Kart Chassis

Design and Simulation of Go Kart Chassis IJIRST International Journal for Innovative Research in Science & Technology Volume 3 Issue 10 March 2017 ISSN (online): 2349-6010 Design and Simulation of Go Kart Chassis Amberpreet Singh Gagandeep Singh

More information

DESIGN AND ANALYSIS OF CAR RADIATOR BY FINITE ELEMENT METHOD

DESIGN AND ANALYSIS OF CAR RADIATOR BY FINITE ELEMENT METHOD DESIGN AND ANALYSIS OF CAR RADIATOR BY FINITE ELEMENT METHOD Prof. V. C. Pathade 1, Sagar R. Satpute 2, Mayur G. Lajurkar 3, Gopal R. Pancheshwar 4 Tushar K. Karluke 5, Niranjan H. Singitvar 6 1 Assistant

More information

FE Modeling and Analysis of a Human powered/electric Tricycle chassis

FE Modeling and Analysis of a Human powered/electric Tricycle chassis FE Modeling and Analysis of a Human powered/electric Tricycle chassis Sahil Kakria B.Tech, Mechanical Engg UCOE, Punjabi University Patiala, Punjab-147004 kakria.sahil@gmail.com Abbreviations: SAE- Society

More information

DESIGN AND OPTIMIZATION OF HTV FUEL TANK ASSEMBLY BY FINITE ELEMENT ANALYSIS

DESIGN AND OPTIMIZATION OF HTV FUEL TANK ASSEMBLY BY FINITE ELEMENT ANALYSIS DESIGN AND OPTIMIZATION OF HTV FUEL TANK ASSEMBLY BY FINITE ELEMENT ANALYSIS GAJENDRA G 1, PRAKASHA A M 2, DR NOOR AHMED R 3, DR.K.S.BADRINARAYAN 4 1PG Scholar, Mechanical department, M S Engineering College,

More information

ISSN: International Journal of Advanced Research in Science, Engineering and Technology. Vol. 3, Issue 7, July 2016

ISSN: International Journal of Advanced Research in Science, Engineering and Technology. Vol. 3, Issue 7, July 2016 Design and Analysis of a High-Pressure EGR Valve for a 4-Cylinder Diesel Engine Rahul Kumar Verma, Abhishek Chakraborty M-Tech Scholar, Automobile Engg, RJIT BSF Academy Tekanpur Assistant Professor, Automobile

More information

CFD ANALYSIS ON LOUVERED FIN

CFD ANALYSIS ON LOUVERED FIN CFD ANALYSIS ON LOUVERED FIN P.Prasad 1, L.S.V Prasad 2 1Student, M. Tech Thermal Engineering, Andhra University, Visakhapatnam, India 2Professor, Dept. of Mechanical Engineering, Andhra University, Visakhapatnam,

More information

Analysis Of Gearbox Casing Using FEA

Analysis Of Gearbox Casing Using FEA Analysis Of Gearbox Casing Using FEA Neeta T. Chavan, Student, M.E. Design, Mechanical Department, Pillai Hoc, Maharashtra, India Assistant Prof. Gunchita Kaur-Wadhwa, Mechanical Department Pillai Hoc,

More information

Modeling and Analysis of Two Wheeler Connecting Rod by Using Ansys

Modeling and Analysis of Two Wheeler Connecting Rod by Using Ansys IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-1684,p-ISSN: 2320-334X, Volume 6, Issue 5 (May. - Jun. 2013), PP 83-87 Modeling and Analysis of Two Wheeler Connecting Rod by Using

More information

Static And Modal Analysis of Tractor Power Take Off (PTO) Gearbox Housing

Static And Modal Analysis of Tractor Power Take Off (PTO) Gearbox Housing Static And Modal Analysis of Tractor Power Take Off (PTO) Gearbox Housing Gopali S Lamani 1, Prof: S.R.Basavaraddi 2, Assistant Professor, Department of Mechanical Engineering, JSPM NTC RSSOER,India1 Professor,

More information

STRUCTURAL ANALYSIS OF TWO WHEELER SUSPENSION FRAME

STRUCTURAL ANALYSIS OF TWO WHEELER SUSPENSION FRAME STRUCTURAL ANALYSIS OF TWO WHEELER SUSPENSION FRAME CH.Neeraja M.tech., Asst.professor,Mech Dept,SACET,Chirala C.R.Sireesha M.tech., Asst.Professor,Mech Dept,QIS,Ongole D.Jawaharlal M.tech., Assoc.Professor,Mech

More information

Design, Analysis & Balancing of 5 Cylinder Engine Crankshaft

Design, Analysis & Balancing of 5 Cylinder Engine Crankshaft International OPEN ACCESS Journal Of Modern Engineering Research (IJMER) Design, Analysis & Balancing of 5 Cylinder Engine Crankshaft Yogesh S. Khaladkar 1, Lalit H. Dorik 2, Gaurav M. Mahajan 3, Anil

More information

International Journal of Engineering Research-Online A Peer Reviewed International Journal Articles available online

International Journal of Engineering Research-Online A Peer Reviewed International Journal Articles available online RESEARCH ARTICLE ISSN: 2321-7758 ANALYSIS OF HEAT TRANSFER RATE BY VARYING COOLING FLUID FOR ENGINE CYLINDER FINS BALUSANI ARUN KUMAR 1, V.NARASIMHA REDDY 2 1 M.Tech Scholar, 2 Asst.Professor Department

More information

ISSN: [ICEMESM-18] Impact Factor: 5.164

ISSN: [ICEMESM-18] Impact Factor: 5.164 IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY FAILURE ANALYSIS OF COUPLER SCREW IN NARROW GAUGE RAILWAYS Mr Tejpal Parshiwanikar Dept of Mechanical Engineering, GHRAET, Nagpur

More information

Simulating Rotary Draw Bending and Tube Hydroforming

Simulating Rotary Draw Bending and Tube Hydroforming Abstract: Simulating Rotary Draw Bending and Tube Hydroforming Dilip K Mahanty, Narendran M. Balan Engineering Services Group, Tata Consultancy Services Tube hydroforming is currently an active area of

More information

STRUCTURAL ANALYSIS OF STEERING YOKE OF AN AUTOMOBILE FOR WITHSTANDING TORSION/ SHEAR LOADS

STRUCTURAL ANALYSIS OF STEERING YOKE OF AN AUTOMOBILE FOR WITHSTANDING TORSION/ SHEAR LOADS STRUCTURAL ANALYSIS OF STEERING YOKE OF AN AUTOMOBILE FOR WITHSTANDING TORSION/ SHEAR LOADS S.K.Chandole 1, M.D.Shende 2, M.K.Bhavsar 3 1 PG Student, Mechanical Engineering, S.N.D. COE & RC, Yeola, Nasik,

More information

BUCKLING ANALYSIS OF CONNECTING ROD

BUCKLING ANALYSIS OF CONNECTING ROD BUCKLING ANALYSIS OF CONNECTING ROD Rukhsar Parveen Mo. Yusuf 1, prof.a.v.karmankar2, Prof.S.D.Khamankar 3 1 Student of M.Tech (CAD/CAM), Rajiv Gandhi College Of Engineering, Research and Technology, Chandrapur(M.S.)

More information

ANALYSIS AND OPTIMIZATION OF CONNECTING ROD USING ALFASiC COMPOSITES

ANALYSIS AND OPTIMIZATION OF CONNECTING ROD USING ALFASiC COMPOSITES ANALYSIS AND OPTIMIZATION OF CONNECTING ROD USING ALFASiC COMPOSITES Kuldeep B 1, Arun L.R 2, Mohammed Faheem 3 P.G. Scholar, Department of Mechanical Engineering, The Oxford college of Engineering, Karnataka,

More information

International Journal of Advance Engineering and Research Development

International Journal of Advance Engineering and Research Development Scientific Journal of Impact Factor (SJIF): 4.14 e-issn (O) : 2348-4470 International Journal of Advance Engineering and Research Development Volume 3, Issue 9, September -2016 p-issn (P) : 2348-6406 Design,

More information

VEHICLE ANTI-ROLL BAR ANALYZED USING FEA TOOL ANSYS

VEHICLE ANTI-ROLL BAR ANALYZED USING FEA TOOL ANSYS VEHICLE ANTI-ROLL BAR ANALYZED USING FEA TOOL ANSYS P. M. Bora 1, Dr. P. K. Sharma 2 1 M. Tech. Student,NIIST, Bhopal(India) 2 Professor & HOD,NIIST, Bhopal(India) ABSTRACT The aim of this paper is to

More information

Finite Element Analysis of Inertia Dynamometer

Finite Element Analysis of Inertia Dynamometer Finite Element Analysis of Inertia Dynamometer R. A. Gujar 1, S. V. Bhaskar 2 & N. U. Yewale 3 1,2&3 Department of Mechanical Engineering, 1&3 Pimpri Chinchwad College of Engineering, 2 Sanjivani Rural

More information

Design and Optimization of HTV Fuel Tank Assembly by Finite Element Analysis

Design and Optimization of HTV Fuel Tank Assembly by Finite Element Analysis Design and Optimization of HTV Fuel Tank Assembly by Finite Element Analysis Ms.Baseera Banushaik PG Student, Department of Mechanical Engineering, Malla Reddy College of Engineering, Secunderabad. Ms.I.Prasanna

More information

Weight reduction of Steering Knuckle by Optimization Method

Weight reduction of Steering Knuckle by Optimization Method Weight reduction of Steering Knuckle by Optimization Method R.P.Gaikwad #1, Prof.Y.P.Reddy *2 #1 P.G Scholar, Department of Mechanical Engineering, Sinhgad College of Engineering, Pune, India *2 Professor,

More information

INFLUENCE OF CERAMIC COATING ON PISTON SURFACE IN I.C ENGINE

INFLUENCE OF CERAMIC COATING ON PISTON SURFACE IN I.C ENGINE INFLUENCE OF CERAMIC COATING ON PISTON SURFACE IN I.C ENGINE V. Mohan 1, N.Surya 2, D.Srinu 3 1, 2, 3 Assistant Professor, Department of Mechanical Engineering, TKRCET, Hyderabad, Telangana, (India) ABSTRACT

More information

Development of Motorized Car Jack

Development of Motorized Car Jack Development of Motorized Car Jack Ravi Kumar D Assistant Professor Mechanical Engineering SRM University Shubham Choudhary U.G. Student Mechanical Engineering SRM University Devanshu Pasbola U.G. Student

More information

Keywords: Stability bar, torsional angle, stiffness etc.

Keywords: Stability bar, torsional angle, stiffness etc. Feasibility of hallow stability bar Prof. Laxminarayan Sidram Kanna 1, Prof. S. V. Tare 2, Prof. A. M. Kalje 3 ABSTRACT: Stability bar also referred to as Anti-rolls bar or sway bar. The bar's torsional

More information

Static Analysis of Crankcase for Single Cylinder High Speed Diesel Engine

Static Analysis of Crankcase for Single Cylinder High Speed Diesel Engine Static Analysis of Crankcase for Single Cylinder High Speed Diesel Engine G.A.Bhosale Department of Mechanical Engineering Dean Academic, Yashwantrao Bhonsale polytechnic, sawantwadi Dr. V.V. Kulkarni

More information

DESIGN AND FABRICATION OF CHASSIS FOR ELECTRICAL VEHICLE

DESIGN AND FABRICATION OF CHASSIS FOR ELECTRICAL VEHICLE DESIGN AND FABRICATION OF CHASSIS FOR ELECTRICAL VEHICLE SHAIK.BALA SAIDULU 1, G.VIJAY KUMAR 2 G.DIWAKAR 3, M.V.RAMESH 4 1 M.Tech Student, Mechanical Engineering Department, Prasad V Potluri Siddhartha

More information

VIBRATION REDUCTION IN CONVENTIONAL VEHICLES BY INCREASING THE STIFFNESS ON THE CHASSIS FRAME

VIBRATION REDUCTION IN CONVENTIONAL VEHICLES BY INCREASING THE STIFFNESS ON THE CHASSIS FRAME VIBRATION REDUCTION IN CONVENTIONAL VEHICLES BY INCREASING THE STIFFNESS ON THE CHASSIS FRAME S. Ganesan and K. Panneerselvam Sathyabama University, Chennai, India E-Mail: ganesuma@gmail.com ABSTRACT The

More information

Address for Correspondence

Address for Correspondence Research Article DESIGN AND STRUCTURAL ANALYSIS OF DIFFERENTIAL GEAR BOX AT DIFFERENT LOADS C.Veeranjaneyulu 1, U. Hari Babu 2 Address for Correspondence 1 PG Student, 2 Professor Department of Mechanical

More information

SPEED DEPENDENT DUAL CALIPER ACTION IN DISC BRAKE

SPEED DEPENDENT DUAL CALIPER ACTION IN DISC BRAKE INTERNATIONAL JOURNAL OF MECHANICAL ENGINEERING AND TECHNOLOGY (IJMET) International Journal of Mechanical Engineering and Technology (IJMET), ISSN 0976 6340(Print), ISSN 0976 6340 (Print) ISSN 0976 6359

More information

DESIGN AND ANALYSIS OF COMPOSITE LEAF SPRING

DESIGN AND ANALYSIS OF COMPOSITE LEAF SPRING International Journal of Mechanical Engineering and Technology (IJMET) Volume 7, Issue 5, September October 2016, pp.177 183, Article ID: IJMET_07_05_019 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=7&itype=5

More information

Design And Analysis Of Two Wheeler Front Wheel Under Critical Load Conditions

Design And Analysis Of Two Wheeler Front Wheel Under Critical Load Conditions Design And Analysis Of Two Wheeler Front Wheel Under Critical Load Conditions Tejas Mulay 1, Harish Sonawane 1, Prof. P. Baskar 2 1 M. Tech. (Automotive Engineering) students, SMBS, VIT University, Vellore,

More information

DESIGN AND MANUFACTURING ELECTRICAL CAR JACK D.C. 12 VOLT

DESIGN AND MANUFACTURING ELECTRICAL CAR JACK D.C. 12 VOLT International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 6, June 207, pp. 200 206, Article ID: IJMET_08_06_02 Available online at http://www.ia aeme.com/ijmet/issues.asp?jtype=ijmet&vtyp

More information

MODEL FREQUENCY ANALYSIS OF AUTOMOTIVE EXHAUST SYSTEM

MODEL FREQUENCY ANALYSIS OF AUTOMOTIVE EXHAUST SYSTEM Research Paper ISSN 2278 ñ 0149 www.ijmerr.com Vol. 3, No. 1, January 2014 2014 IJMERR. All Rights Reserved MODEL FREQUENCY ANALYSIS OF AUTOMOTIVE EXHAUST SYSTEM D Jai Balaji 1*, P V Srihari 1 and Veeranna

More information

COMPARATIVE ANALYSIS OF CRANKSHAFT IN SINGLE CYLINDER PETROL ENGINE CRANKSHAFT BY NUMERICAL AND ANALYTICAL METHOD

COMPARATIVE ANALYSIS OF CRANKSHAFT IN SINGLE CYLINDER PETROL ENGINE CRANKSHAFT BY NUMERICAL AND ANALYTICAL METHOD COMPARATIVE ANALYSIS OF CRANKSHAFT IN SINGLE CYLINDER PETROL ENGINE CRANKSHAFT BY NUMERICAL AND ANALYTICAL METHOD Mr. Anant B. Khandkule PG Student Mechanical Engineering Department, Sinhgad Institute

More information

Design and Stress Analysis of Crankshaft for Single Cylinder 4-Stroke Diesel Engine

Design and Stress Analysis of Crankshaft for Single Cylinder 4-Stroke Diesel Engine Design and Stress Analysis of Crankshaft for Single Cylinder 4-Stroke Diesel Engine Amit Solanki #1, Jaydeepsinh Dodiya #2, # Mechanical Engg.Deptt, C.U.Shah University, Wadhwan city, Gujarat, INDIA Abstract

More information

Design and Analysis of Clutch Plate for Automatic Single Plate Clutch

Design and Analysis of Clutch Plate for Automatic Single Plate Clutch ISSN 2395-1621 Design and Analysis of Clutch Plate for Automatic Single Plate Clutch #1 Ravikiran M. Tate, #2 S. H. Sarje 1 rtate26@gmail.com 2 suhas_sarje7@rediffmail.com #12 Mechanical Department, JSPM

More information

S.Sivaraj #1, A.Hazemohzammed *1, M.Yuvaraj *2, N.Karthikeyan *3, V.Murugan *4, # Assistant Prof., Dept, * U.G Students,

S.Sivaraj #1, A.Hazemohzammed *1, M.Yuvaraj *2, N.Karthikeyan *3, V.Murugan *4, # Assistant Prof., Dept, * U.G Students, Structural Analysis of Ladder Chassis Frame for car UsingAnsys S.Sivaraj #1, A.Hazemohzammed *1, M.Yuvaraj *2, N.Karthikeyan *3, V.Murugan *4, # Assistant Prof., Dept, * U.G Students, Dept of mechanical

More information

International Journal of Science Engineering and Advance Technology, IJSEAT, Vol. 3, Issue 12 ISSN December-2015

International Journal of Science Engineering and Advance Technology, IJSEAT, Vol. 3, Issue 12 ISSN December-2015 Modeling and Thermal Conduction and Static Analysis of an IC Engine Piston using CATIA V5 Tool and ANSYS Sangeetham Sivakumar #1, Guru Murthy N #2, P.Satish Reddy #3 Scholar of Master of Technology, Asst

More information

NASA Human Exploration Rover Design and Analysis

NASA Human Exploration Rover Design and Analysis NASA Human Exploration Rover Design and Analysis Nikhil Anand Student(B-tech mechanical) Chandigarh University nikhil.anand333@yahoo.c om Raghav Sharma Student(B.E mechanical) Chandigarh University raghavshs@gmail.com

More information

ANALYSIS OF GEAR QUALITY CRITERIA AND PERFORMANCE OF CURVED FACE WIDTH SPUR GEARS

ANALYSIS OF GEAR QUALITY CRITERIA AND PERFORMANCE OF CURVED FACE WIDTH SPUR GEARS 8 FASCICLE VIII, 8 (XIV), ISSN 11-459 Paper presented at Bucharest, Romania ANALYSIS OF GEAR QUALITY CRITERIA AND PERFORMANCE OF CURVED FACE WIDTH SPUR GEARS Laurentia ANDREI 1), Gabriel ANDREI 1) T, Douglas

More information

INTERNATIONAL JOURNAL OF DESIGN AND MANUFACTURING TECHNOLOGY (IJDMT) CONSTANT SPEED ENGINE CONROD SOFT VALIDATION & OPTIMIZATION

INTERNATIONAL JOURNAL OF DESIGN AND MANUFACTURING TECHNOLOGY (IJDMT) CONSTANT SPEED ENGINE CONROD SOFT VALIDATION & OPTIMIZATION INTERNATIONAL JOURNAL OF DESIGN AND MANUFACTURING TECHNOLOGY (IJDMT) International Journal of Design and Manufacturing Technology (IJDMT), ISSN 0976 6995(Print), ISSN 0976 6995 (Print) ISSN 0976 7002 (Online)

More information

PIONEER RESEARCH & DEVELOPMENT GROUP

PIONEER RESEARCH & DEVELOPMENT GROUP Design and Stress Analysis of Tow Bar for Medium Sized Portable Compressors Pankaj Khannade 1, Akash Chitnis 2, Gangadhar Jagdale 3 1,2 Mechanical Department, University of Pune/ Smt. Kashibai Navale College

More information

Modeling & Impact Analysis of a Car Bumper with Different Loads on Different Materials

Modeling & Impact Analysis of a Car Bumper with Different Loads on Different Materials Modeling & Impact Analysis of a Car Bumper with Different Loads on Different Materials V.Siva Kumar 1, S.Timothy 2, M.Naga Kiran 3 P.G. Student, Department of Mechanical Engineering, Vignana Bharathi Institute

More information

ISSN: [Patil et al., 5(10): October, 2016] Impact Factor: 4.116

ISSN: [Patil et al., 5(10): October, 2016] Impact Factor: 4.116 IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY DESIGN AND ANALYSIS OF TELESCOPIC HALFSHAFT FOR AN ALL-TERRAIN VEHICLE (ATV) Chirag Patil *, Sandeep Imale, Kiran Hiware, Sumeet

More information

EXPERIMENTAL ANALYSIS AND TOPOLOGY OPTIMIZATION OF LOWER SUSPENSION ARM OF CAR

EXPERIMENTAL ANALYSIS AND TOPOLOGY OPTIMIZATION OF LOWER SUSPENSION ARM OF CAR EXPERIMENTAL ANALYSIS AND TOPOLOGY OPTIMIZATION OF LOWER SUSPENSION ARM OF CAR Rupali Dhore 1, Prof. M.L. Thorat 2 1B.E.MECH. (M.E.Pursuing), Mechanical Department, RMD SINHGAD SCHOOL OF ENGINEERING, PUNE

More information

COMPARISON OF ANALYTICAL & FEA OF CONTACT ANALYSIS OF SPUR GEAR DRIVE

COMPARISON OF ANALYTICAL & FEA OF CONTACT ANALYSIS OF SPUR GEAR DRIVE COMPARISON OF ANALYTICAL & FEA OF CONTACT ANALYSIS OF SPUR GEAR DRIVE Sachin Almelkar 1, Prof I.G.Bhavi 2 1M.Tech (Machine Design). B L D E A s Dr.P.G. Halakatti College Of Engineering and Technology,Vijayapur,

More information

FAILURE ANALYSIS OF CYLINDER HEAD VALVE SPRING IN LOCOMOTIVES

FAILURE ANALYSIS OF CYLINDER HEAD VALVE SPRING IN LOCOMOTIVES FAILURE ANALYSIS OF CYLINDER HEAD VALVE SPRING IN LOCOMOTIVES MOORTHY G 1, BALAKRISHNAN S 2, CHITHARTHAN S 3, RANJITH KUMAR V 4 1PG scholar, Department of Manufacturing Engineering, Government College

More information

CHAPTER 5 PREVENTION OF TOOTH DAMAGE IN HELICAL GEAR BY PROFILE MODIFICATION

CHAPTER 5 PREVENTION OF TOOTH DAMAGE IN HELICAL GEAR BY PROFILE MODIFICATION 90 CHAPTER 5 PREVENTION OF TOOTH DAMAGE IN HELICAL GEAR BY PROFILE MODIFICATION 5.1 INTRODUCTION In any gear drive the absolute and the relative transmission error variations normally increases with an

More information

Increase Factor of Safety of Go-Kart Chassis during Front Impact Analysis

Increase Factor of Safety of Go-Kart Chassis during Front Impact Analysis IJIRST International Journal for Innovative Research in Science & Technology Volume 3 Issue 04 September 2016 ISSN (online): 2349-6010 Increase Factor of Safety of Go-Kart Chassis during Front Impact Analysis

More information

BIKE SPIRAL SPRING (STEEL) ANALYSIS

BIKE SPIRAL SPRING (STEEL) ANALYSIS BIKE SPIRAL SPRING (STEEL) ANALYSIS Yaluppa Madhukar Benake 1, Prof.Santosh Mali Patil 2 1 M.Tech.,Mechanical Engg. Dept., MMEC, Belagavi 2 Assistant Prof. Mechanical Engg. Dept. MMEC, Belagavi Abstract

More information

Design/Modeling and Thermal Analysis on Cylinder Head of I.C Engine

Design/Modeling and Thermal Analysis on Cylinder Head of I.C Engine Design/Modeling and Thermal Analysis on Cylinder Head of I.C Engine G.Bahadur Vali Department of Mechanical, Chebrolu Engineering College. Abstract: A cylinder head is made of box type of section of considerable

More information

DESIGN AND OPTIMIZATION OF TWO WHEELER PISTON MATERIAL USING ALUMINUM ALLOY 6061 AND ALUMINUM ALLOY 7475-T761

DESIGN AND OPTIMIZATION OF TWO WHEELER PISTON MATERIAL USING ALUMINUM ALLOY 6061 AND ALUMINUM ALLOY 7475-T761 DESIGN AND OPTIMIZATION OF TWO WHEELER PISTON MATERIAL USING ALUMINUM ALLOY 6061 AND ALUMINUM ALLOY 7475-T761 Nampally Saikiran 1, Dr P. SampathRao 2 1 PG Student Department of Mechanical Engineering,

More information

Design and Front Impact Analysis of Rollcage

Design and Front Impact Analysis of Rollcage International Conference on Challenges and Opportunities in Mechanical Engineering, Industrial Engineering and Management Studies 7 Design and Front Impact Analysis of Rollcage Gautam Yadav and Ankit Jain

More information

Static Analysis of Crankcase and Crankshaft of Single Cylinder Four Stroke Diesel Engine

Static Analysis of Crankcase and Crankshaft of Single Cylinder Four Stroke Diesel Engine Static Analysis of Crankcase and Crankshaft of Single Cylinder Four Stroke Diesel Engine Kakade Pratik 1 Post Graduate Student kakadepratik@gmail.com Pasarkar M. D. 2 Assistant Professor mdpasarkar@gmail.com

More information

MODELLING AND STRUCTURAL ANALYSIS OF A GO-KART VEHICLE CHASSIS FRAME

MODELLING AND STRUCTURAL ANALYSIS OF A GO-KART VEHICLE CHASSIS FRAME International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 6, June 2017, pp. 305 311, Article ID: IJMET_08_06_031 Available online at http://www.ia aeme.com/ijmet/issues.asp?jtype=ijmet&vtyp

More information

IJRASET: All Rights are Reserved

IJRASET: All Rights are Reserved Failure Analysis and Design Modification of Propeller Shaft of Bus Sweety P. Mhaske¹, Nitin P. Doshi² PG Scholar Mechanical Engg, Bapurao Deshmukh College of Engg & Technology, Sevagram, Wardha, Maharashtra,

More information

Design, Modelling & Analysis of Double Wishbone Suspension System

Design, Modelling & Analysis of Double Wishbone Suspension System Design, Modelling & Analysis of Double Wishbone Suspension System 1 Nikita Gawai, 2 Deepak Yadav, 3 Shweta Chavan, 4 Apoorva Lele, 5 Shreyash Dalvi Thakur College of Engineering & Technology, Kandivali

More information

STRESS AND THERMAL ANALYSIS OF CLUTCH PLATE

STRESS AND THERMAL ANALYSIS OF CLUTCH PLATE International Journal of Mechanical Engineering and Technology (IJMET) Volume 9, Issue 3, March 2018, pp. 611 618, Article ID: IJMET_09_03_063 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=9&itype=3

More information

DESIGN AND FINITE ELEMENT ANALYSIS OF UNDER FRAME ARRANGEMENT (UNIVERSAL HEADSTOCK) OF DUAL COUPLER FOR RAILWAY COACHES

DESIGN AND FINITE ELEMENT ANALYSIS OF UNDER FRAME ARRANGEMENT (UNIVERSAL HEADSTOCK) OF DUAL COUPLER FOR RAILWAY COACHES DESIGN AND FINITE ELEMENT ANALYSIS OF UNDER FRAME ARRANGEMENT (UNIVERSAL HEADSTOCK) OF DUAL COUPLER FOR RAILWAY COACHES Pothamsetty Kasi Visweswar Rao 1 1 Assistant Professor, Department of Mechanical

More information