INSTALLATION AND OWNER S MANUAL Wing Deflectors, Fairing Mount N5107 and N5109 for HONDA GL1800
|
|
- Charlene Cameron Turner
- 5 years ago
- Views:
Transcription
1 INSTALLATION AND OWNER S MANUAL Wing Deflectors, Fairing Mount N5107 and N5109 for HONDA GL1800 Thank you for purchasing a National Cycle product. Please read these instructions carefully and thoroughly before beginning work. Dealers if installing this product for a customer please give them this manual. It contains information needed to properly maintain and use this product. Report any missing parts directly to National Cycle, Inc. There is important code information located on the back of the the package that will be necessary when reporting missing parts. Attention Special notes and cautionary measures which can prevent damage to the accessory or motorcycle. Note Tips for facilitation of operation,control and adjustment, as well as maintenance. PARTS LIST Item Part Number Description Qty. Note 1 Wing Deflector, Dark Tint, Upper 2 Contained in N Wing Deflector, Dark Tint, Left, Lower 1 Contained in N Wing Deflector, Dark Tint, Right, Lower 1 Contained in N Wing Deflector, Light Tint, Upper 2 Contained in N Wing Deflector, Light Tint, LH Lower 1 Contained in N Wing Deflector, Light Tint, RH Lower 1 Contained in N Bracket, Left 1 5 Bracket, Right 1 6 Drill Bit 1 Used in Installation Template, Left and Right Side 1 Page 5 of Installation Manual BAG# Screw, 4-20 x 1/ Washer M Washer, Neoprene Stand-off Screw, x 3/ Circle, Mylar 6 12x x13 6 8x13 9x12 11x4 10x4 3 Right and Left side of Motorcycle is determined while sitting on the bike. 2 5mm Hex Key Wrench 1/2 Socket and Torque Wrench Thread Locker (Loctite 271 or equivalent) Scissor Tape Drill Press or Hand Drill, Not Shown Flat Piece of Wood (for use when drilling) 1/8 Hex Key Wrench #1 Phillips Screw Driver 2010 National Cycle, Inc. PO Box 158, Maywood, IL USA Page 1 of /10
2 PREPARATION AND DRILLING OF TRIM STRIP 1. Position motorcycle securely on center stand or side stand. 2. Carefully remove Right side trim piece (a). Start at the bottom of strip, pull strip from the inside edge towards the outside of the fairing gently lifting as you pull. As the bottom edge is released, work your way upward taking care not to break the retaining tabs. Figure 1 3. Remove Screws (b) (5mm Hex Key). Figure 2 4. Apply a small amount of Thread Lock to the threaded side of the Standoffs. Replace the screws removed in Step 3 with these threaded fasteners. Tighten securely. 4 ft/lb (5.4Nm) (1/2 Socket, Thread Locker) Figure 3 5. Cut Right Template from page 5. (Scissors) Figure 4 6. With markings on Template facing up, align Template between notches on inside of trim strip. Tape Template into postion. (Tape) Figure 5 Before you drill, check postion of template by holding trim piece into position on the right side of motorcycle. 7. Make a pilot mark on strip at center of cross marks. (Drill Bit Provided) Figure 5 8. Carefully drill each hole using a slow speed. A drill press is preferred, however a hand drill can be used. Place the trim strip on a clean flat piece of wood for support while drilling. Use caution as required by the use of power equipment. Remove the paper template. (Drill Bit Provided and Drill) Figure 5 9. Repeat procedure on Left side of motorcycle. b b a Figure 1 Figure 2 Figure 4 Figure 3 Figure National Cycle, Inc. PO Box 158, Maywood, IL USA Page 2 of /10
3 INSTALLATION OF BRACKET and WING DEFLECTORS 1. Replace the trim strips to the fairing working opposite of the way they were removed. Starting at the top push the top edge of the trim strip into the slot and work the outside edges strip into the notches and gently push in the back edges. Work your way down to the bottom of the trim strip. Holes in trim should align with standoffs. Figure 6 2. Install Right Bracket with 3/8 Screws. (1/8 Hex Key) Figure 7 3. Position Swivel Ratchet so studs face toward rider. Figure 7 4. Install Neoprene Washers on studs. Figure 8 5. Use a Washer and a 1/4 Screw to attach Upper and Lower Deflectors to Swivel Ratchet. (Phillips Screw Driver) Figure 9 and Tighten Screws firmly, do not over-tighten. (Phillips Screw Driver) 6 in/lb (.7Nm) 7. Repeat procedure on Left side of motorcycle. Figure 6 Figure 7 Figure 8 Figure 9 Figure National Cycle, Inc. PO Box 158, Maywood, IL USA Page 3 of /10
4 CHECK CLEARANCES 1. Refer to USING YOUR WING DEFLECTORS below and, if desired, place the mylar disks over the contact points on the fairing where the deflectors touch. Figure 11 Gently turn handle bar left and right to full fork lock to assure that no interference occurs between the Wing Deflector and any part of the motorcycle or other accessory mounted to the motorcycle. Make adjustments or remove accessory as necessary. USING YOUR WING DEFLECTORS 1. In cold and or wet weather close deflectors up to fairing for maximum wind and rain deflection. 2. In moderate to hot weather open deflectors for desired air flow. Closing lower deflectors in hot weather can help deflect hot air from the radiators away. 3. For ultimate performance use Wing Deflectors in conjunction with our mirror mounted deflectors and VStream windshield. Figure 11 MAINTENANCE Cleaning: Wash with a clean soft cloth, plenty of warm water and, if necessary, a non-abrasive soap such as dishwashing Do not allow brake fluid, alcohol, or strong solvents to contact the plastic. National Cycle Windshield Wash Part number N1401 is recommended for everyday cleaning. Product is supplied with a handy travel size container and rag for easy storage on the motorcycle. Inquire with your local dealer or visit: National Cycle 3-Year Limited Warranty Register your Wing Deflectors on Line at: Customer Service, National Cycle, Inc. / PO Box 158 / Maywood, IL / USA 708/343/0400 National Cycle hereby warrants to the original registered owner of a National Cycle polycarbonate product for a period of three years from the date of purchase against breakage. This limited warranty is expressly limited to the replacement of the polycarbonate deflectors. This limited warranty does not include scratches, coating failure, cosmetic wear and tear, replacement of hardware, or any consequential damages or expenses including labor cost of installation, removal and/or replacement, inconvenience, inbound freight expenses or damage to any other component of the motorcycle or any other accessories. Certain chemicals, generally known as acidic hydrocarbons, are known to cause polycarbonate damage and will not be covered under this limited warranty. Please refer to the cleaning instructions supplied. Never ride your motorcycle with loose accessory mounting hardware. Check the hardware for tightness regularly. Today s motorcycles are built with enough frame rigidity to withstand the moderate loads imposed on them by the foreseeable addition of an accessory. If the accessory(ies) adversely affects your motorcycle s stability, immediately remove the accessory(ies). Do not ride a motorcycle that exhibits unsafe handling traits. Have experienced service personnel correct any problem before riding with the accessory(ies) installed. For further questions concerning handling problems associated with an accessory(ies), contact your dealer, motorcycle manufacturer, or accessory manufacturer National Cycle, Inc. PO Box 158, Maywood, IL USA Page 4 of /10
5 Use this guide to verify your printed template for exact 100% scaling TOP TOP 4.83 LEFT RIGHT Page 5 of /10
Register your windshield online at National Cycle 3-Year Limited Warranty
Quantum Hardcoated Polycarbonate Street Shield Windshield N5010, 7/8 (mm) Bars N501, 1 (5mm) Bars and N5014, 1.5 (1.5mm) Bars Thank you for purchasing a National Cycle product. Read these instructions
More informationInstallation and Owner s Manual for Quantum Hard Coat Polycarbonate Windscreen for Honda PCX150/125
Installation and Owner s Manual for Quantum Hard Coat Polycarbonate Windscreen for Honda PCX150/125 N50001 Short, N50002 Mid Size, N50003 Tall Thank you for purchasing a National Cycle Accessory. Before
More informationParts List Continues on Next Page
Assembly Instructions and Owner s Manual Description: Quantum Hardcoated Polycarbonate UTV Windshield, Wash n Wipe Full Size Model: Part Number: N30202 Installation Time: 60 min Polaris RZR 800, Round
More informationN41422 Peacemakers Exhaust for Harley- Davidson Dyna Series 2006
Please read these instructions carefully and thoroughly before beginning work. Before installing accessory, carefully consider whether one possesses the necessary technical skills and workshop tools to
More informationPARTS LIST. REPLACEMENT PARTS and ACCESSORIES PREPARATION VN1600. PREPARATION VN1500D and VN800B
INSTALLATION AND OWNER S MANUAL Light Bar N925 for Installation to: Kawasaki VN1500D&E and VN800B Pages 1,2,3 and 5 Kawasaki VN1600 Pages 1, 4 and 5 PARTS LIST QTY. PART NO. DESCRIPTION 1 N925 Light Bar
More informationLexan Hardcoated Polycarbonate VStream Windscreen Z2476, Z2477 and Z2478 for F800GT
Lexan Hardoated Polyaronate VStream Windsreen Z246, Z24 and Z248 for F800GT Thank you for purhasing a ZTehnik produt. Read these instrutions arefully and thoroughly efore eginning work. Dealers, if installing
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT-CARBON FIBER REAR SPOILER INFINITI Q50 T99J1 J5000 KIT CONTENTS: Item A B C D Qty. 1 4 1 1 Part Description Spoiler Assembly
More informationw w w. h d o n l i n e s h o p. d e DETACHABLE WINDSHIELD AND DOCKING HARDWARE KIT GENERAL INSTALLATION -J00325 REV Kit Number Models
-J00 REV. 00-- DETACHABLE WINDSHIELD AND DOCKING HARDWARE KIT GENERAL Kit Number -A, 0-, -, 0-, -, - 0, -0 Models These kits fit and later FXST, FXSTB, FXSTC, and and later FXDWG Harley-Davidson model
More informationKawasaki Motors Corp.,U.S.A. Irvine, CA
Kawasaki Motors Corp.,U.S.A. Irvine, CA 9271-2016 Accessory Part Installation Instructions For Model VN900 Classic Windshield Kit: Part No. 99994-005 Please read these instructions carefully and thoroughly
More informationGround Effects, P/N: (V6), (V8)
, P/N: 92248596 (V6), 92248560 (V8) 3. Open trunk and remove 3 scrivets per side. Retain. Remove LH and RH tail lamp access cover. Retain. Refer to Figure 1. NOTE: Installation is made easier with the
More informationVOLKSWAGEN AMAROK 3 PIECE HARD TONNEAU COVER INSTALLATION INSTRUCTIONS
VOLKSWAGEN AMAROK 3 PIECE HARD TONNEAU COVER INSTALLATION INSTRUCTIONS Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents. Place these
More informationN41421 Peacemakers Exhaust for Harley- Davidson Dyna Series
Please read these instructions carefully and thoroughly before beginning work. Before installing accessory, carefully consider whether one possesses the necessary technical skills and workshop tools to
More information99-03 V6 "Shaker" System Instructions. *03 Model requires new hood Contents w/ Kit. Tool List For Appliqué:
99-03 V6 "Shaker" System Instructions *03 Model requires new hood Contents w/ Kit 1 - Hood Appliqué 1 - Aluminum Shaker Scoop 1 - Lower Air Box w/drain tube fittings (2) 1 - Upper Air Box w/cdc nameplate
More informationINSTALLATION. Note: Not all of the included parts will be used during this installation. -cont.-
Driving Lights for Road Glide 5007 Fits: 98-up Road Glide PartS Included 1 Right Light Assembly 1 Left Light Assembly 1 Right Mounting Bracket 1 Left Mounting Bracket 1 Hardware Kit Including: 2 Narrow
More informationINSTALLATION AIRMASTER DELUXE FAIRING 1335
AIRMASTER DELUXE FAIRING 1335 PARTS INCLUDED 1 Airmaster Fairing 1 Dragon Wing Spacer kit 1 Light Bar Relocation Hardware Kit 2 1/2" Spacers 2 1" Spacers 6 5/16"-24 x 1" Button Head Cap Screw, Chrome 4
More informationSUBARU FORESTER - SIDE STEP DIESEL VERSION INSTALLATION INSTRUCTIONS
SUU FORESTER - SIDE STEP DIESEL VERSION INSTALLATION INSTRUCTIONS SS00 VEHICLE DESCRIPTION: PART NUMBER: SUU FORESTER SACC00 R 9 L 0 Care Instructions: Clean Side Steps with a mild detergent and water
More informationINSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE GL1500 RAKE KIT
INSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE GL1500 RAKE KIT Thank you for choosing the Motor Trike GL1500 Rake Kit. We ask that you read the directions before you start and follow them very closely.
More informationTORCH Main Grille Main grille INSERT - # / # Chevrolet Silverado
Parts included (1) TORCH Grille - Main (1) 40 LED - Part #6311271 OR Stealth - Part #6311271-BR OR (1) 30 LED - Part #6311281 OR Stealth - Part #6311281-BR Hardware included (1) - Large Bottom Mounting
More informationMustang V6 Shaker 99-04* Components Check List:
Mustang V6 Shaker 99-04* Components Check List: *03 Model requires new hood CDC Inspected Installer Check Quantity Descriptions 1- Hood Appliqué 1- Aluminum Shaker Scoop 1- Lower Air Box w/drain tube fittings
More informationw w w. h d o n l i n e s h o p. d e ROAD KING FAT HANDLEBAR KIT GENERAL PREPARATION - ALL MODELS -J02375 REV Kit Number Models ABS Models
-J02375 REV. 2008--9 GENERAL Kit Number 56675-05 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English only). ABS Models
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Hood Bug Deflector Pathfinder T99D5 9PJ0A KIT CONTENTS: Item Qty. A 2 Inner Clip A B 2 Outer Clip B C 2 Wing Clip C D 1 Hood
More informationINSTALLATION AND OWNER S MANUAL Side Illumination Lights Z5150 for use with K 1200 LT
INSTALLATION AND OWNER S MANUAL Side Illumination Lights Z5150 for use with K 1200 LT Read these instructions carefully and thoroughly before beginning work. Before installing the accessory, carefully
More informationUpper Class Grille Main grille INSERT - #54127 / #54131 / #54133 / #51127 / #51131 / 51133
Parts included (1) - Main Full Opening - Polished - Part #54127 OR 1 Bar - Polished - Part #54131 OR 2 Bar - Polished - Part #54133 OR Full Opening - Black - Part #51127 OR 1 Bar - Black - Part #51131
More information3PC TONNEAU COVER WITH SPORTS BAR INSTALLATION INSTRUCTIONS
3PC TONNEAU COVER WITH SPORTS BAR INSTALLATION INSTRUCTIONS TC00d / Vehicle Description: NISSAN NAVARA D0 DUAL CAB 3-PIECE TONNEAU COVER PARTS LIST NO. PART NAME QTY. NO. PART NAME QTY. NO. PART NAME QTY.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory FABRIC FRONT DOORS P/N 0SR90-HL4-211A (BLACK) P/N 0SR90-HL4-221A (CAMO) Application SXS1000M3/M3P/M5P/M5D Honda Dealer: Please give a copy of these instructions to your
More information2011 Honda Accord Coupe Fine Mesh Grille
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! TOOLS REQUIRED 2011 Honda Accord Coupe Fine Mesh Grille Replacement Upper / Lower Overlay Part #: Complete #1124-0102-11 / Black Ice
More informationSPECIALTY TOP CO. STC INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTTRAC TOP PART # BRONCO
STC INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTTRAC TOP PART #331-310 BRONCO 1966-1977 SPECIALTY TOP CO. Thank you for purchasing Specialty's Convertible Top for your Bronco. It has been designed for
More informationCAB #11670 FOR JOHN DEERE 2320 TRACTOR
CAB #11670 FOR JOHN DEERE 2320 TRACTOR OPERATION - PARTS LIST - ASSEMBLY IMPORTANT READ THIS MANUAL CAREFULLY AND KEEP FOR FUTURE REFERENCE CAUTION! REMOVE THE VINYL PANELS FOR TRANSPORT IN AN OPEN TRUCK
More informationCAB #11606 FOR John Deere X500, X520, X530, X534, X540
CAB #11606 FOR John Deere X500, X520, X530, X534, X540 ASSEMBLY INSTRUCTIONS PARTS LIST IMPORTANT READ THIS MANUAL CAREFULLY AND KEEP FOR FUTURE REFERENCE CAUTION! REMOVE THE VINYL PANELS FOR TRANSPORT
More informationGP1-R FULL EXHAUST SUZUKI GSX-R600 / GSX-R
THIS EXHAUST SYSTEM IS DESIGNED FOR USE IN CLOSED COURSE RACING ONLY, AND IS NOT INTENDED FOR PUBLIC HIGHWAY USE. IN THE STATE OF CALIFORNIA, IT IS ILLEGAL TO MODIFY THE EMISSION CONTROL SYSTEM ON ANY
More informationPOLY TIP-DOWN WINDSHIELD KIT
POLY TIP-DOWN WINDSHIELD KIT P/N 2883261 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationInstallation Instructions. Ventvisor Deflector
Installation Instructions Important Safety Information Ventvisor Deflector For proper installation and best possible fit, please read all instructions BEFORE you begin. CAUTION - Before driving, ensure
More informationH15P. Toyota Hilux A-DECK Dual Cab
Toyota Hilux A-DECK Dual Cab Page 1 of 14 Fitting Instructions Part Number H15 Toyota Hilux A-DECK Dual Cab 2015+ To suit Sports Bars Check contents of kit before commencing fitment and report any discrepancies
More informationREVOLVER SERIES GRILLES - INSTALLATION GUIDE
REVOLVER SERIES GRILLES - INSTALLATION GUIDE Depending on your style and your preferred look of the vehicle, you have the option to install the Raw Aluminum Trim Piece, Color Match, or just opt to leave
More informationFIRST TIME INSTALLATION
LOCKN LOAD TM PLATFORM MAX PLATFORM LOAD RATING: 100 KG (sizes A, B, F, G, I, K, & L) 150 KG (sizes C, D, E, H, J, N, P & U) PLEASE REFER TO VEHICLE MANUFACTURER SPECIFICATIONS FOR MAX ROOF LOAD RATING
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: Moonroof Wind Deflector Nissan Altima PART NUMBER: 999D UZ000 KIT CONTENTS: Item Qty. Description Service Part Number A B C D E F G H 1
More information# CAB For Snapper Turf Cruiser and Trail Cruiser
# 7600015 CAB For Snapper Turf Cruiser and Trail Cruiser OPERATION - PARTS LIST - ASSEMBLY IMPORTANT! READ THIS MANUAL CAREFULLY AND KEEP FOR FUTURE REFERENCE CAUTION REMOVE THE VINYL PANELS FOR TRANSPORT
More informationPOLY TIP-DOWN WINDSHIELD KIT
POLY TIP-DOWN WINDSHIELD KIT P/N 2881919 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationTOYOTA KLUGER / HIGHLANDER. (2010 Production Onwards) INTEGRATED SIDE STEPS INSTALLATION INSTRUCTION. 60 Minutes
TOYOTA KLUGER / HIGHLANDER (2010 Production Onwards) INTEGRATED SIDE STEPS INSTALLATION INSTRUCTION Accessory Part No. STEP0003 60 Minutes Approx Product Weight: 33 lbs 15KG IMPORTANT - PLEASE READ INSTRUCTIONS
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW LIFT MOTOR
REMOVAL/INSTALL OF WINDOW REGULATOR (742-269) Ford Mustang 1996 2004 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More informationReplace - A - Top Installation Instructions
Replace - A - Top Installation Instructions For: Suzuki Samurai Part Number: 51361 Congratulations on your purchasing decision. Bestop designed this Convertible Top to give you years of dependability and
More informationASSEMBLY & INSTALLATION INSTRUCTIONS
ASSEMBLY & INSTALLATION INSTRUCTIONS VEHICLE MOUNT KIT 99101087 AND VEHICLE CENTER MEMBER For 26 Series: 99100890 TO FIT 2009 & Later FORD F150 4x4 (without EcoBoost V6) 2011 & Later FORD F150 4x4 (with
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory MOON P/N 08R01-SZA-101 Application 2014 PILOT Publications No. AII 50258 Issue Date AUG 2013 PARTS LIST TOOLS AND SUPPLIES REQUIRED Phillips screwdriver 10 mm Combination
More information1PC TONNEAU COVER INSTALLATION INSTRUCTIONS. Ford Ranger (with bedliner)
PC TONNEAU COVER INSTALLATION INSTRUCTIONS Ford Ranger (with bedliner) Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents. Place these
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 3.5 CONTOUR BULL BAR AUTOMOTIVE PRODUCTS, APPLICATION: 0-06 Chevrolet Silverado 500 PART NUMBER: 3-3000, 3-3005, 3-3005T, 3-3090, 3-3095, 3-3095T ITEM QUANTITY DESCRIPTION TOOLS
More informationINSTALLATION INSTRUCTIONS SEMI Hidden Kit Part Number: Application: 2017 Toyota 4Runner
INSTALLATION INSTRUCTIONS SEMI Hidden Kit Part Number: 100022 Application: 2017 Toyota 4Runner GENERAL SAFETY PRECAUTIONS Your safety, and the safety of others, is very important. To help you make informed
More informationPreparation Part Number: PT Kit Contents Item # Quantity Reqd. Description 1 1 Rear Spoiler 2 1 Hardware Kit. Hardware Bag Contents
Preparation Part Number: PT478-11170-09 Kit Contents 1 1 Rear Spoiler 2 1 Hardware Kit Hardware Bag Contents 1 4 M5 Nut 2 4 Clip 3 4 Hole Plug Additional Items Required For Installation 1 1 Outer Drill
More informationINSTALLATION BLIND SPOT TURN SIGNAL MIRRORS 1457
BLIND SPOT TURN SIGNAL MIRRORS 1457 PARTS INCLUDED 2 Blind Spot Turn Signal Mirror Assemblies 1 Wire Harness Kit Including: 2 Wiring Harness (four pin) 1 Adapter Harness (six pin) 2 3-Pin Female Connectors
More information2015+ Mustang Rear Valance Installation Instructions P/N: (R F953) (R F953BS)
2015+ Mustang Rear Valance Installation Instructions P/N: 421894 (R1315-17F953) 421919 (R1315-17F953BS) 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015+ Mustang Rear Valance Kit Installation
More informationFord Mustang Rear Decklid Spoiler Kit. Installation Instructions
Ford Mustang Rear Decklid Spoiler Kit Application: 2005-09 Ford Mustang Installation Instructions Before installing your ROUSH Performance Product(s), read through the entire installation procedure and
More informationTOYOTA RAV RUNNING BOARD
TOYOTA RAV4 2013 - RUNNING BOARD Part Number: 00016-42020 Accessory Code:TR1 Conflicts Mudguard Kit Contents Item # Quantity Reqd. Description 1 1 LH Board Assembly 2 1 RH Board Assembly 3 1 LH Rear Mounting
More informationINSTALLATION INSTRUCTIONS
PART NO. 23100T PRODUCT DESCRIPTION: Front Winch Bumper, Center Section PRODUCT SAFETY & LEGAL DISCLAIMER IMPORTANT READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE PERSONAL
More informationIncluded in Hardware Kit. Rear Corners 2-Door. Jeep JK Trail Armor. Set Part #14009 Rev STEP 1 - PRIOR TO INSTALLATION
Jeep JK Trail Armor Set Part #14009 Rev-2 02-23-11 A) B) C) STEP 1 - PRIOR TO INSTALLATION Bushwacker only approves installing the trail armor according to these written instructions with the hardware
More informationMustang CLASSIC LIGHT BAR INSTALLATION INSTRUCTIONS CDC #
1990-1993 Mustang CLASSIC LIGHT BAR INSTALLATION INSTRUCTIONS CDC # 101000 Kit Components: 1 Light Bar 4 Bolts ( 5 / 16-18 x 2.5 ) #182010 4 Washer #182005 4 Shims #182009 2 Dark Blue Connectors #182004
More informationw w w. h d o n l i n e s h o p. d e CHROME FAN KIT GENERAL INSTALLATION -J04347 REV Kit Number Models Kit Contents
-J0447 REV. 008-08-05 CHROME FAN KIT GENERAL Kit Number 996-08 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com (English
More information/ GMC SIERRA 2500 / 3500 START HERE BEFORE YOU BEGIN STEP 2
2015-2016 CHEVROLET SILVERADO 2500 / 3500 / 2015-2016 GMC SIERRA 2500 / 3500 Z321221 / Z321221-KIT FRONT BUMPER LED LIGHT MOUNTS Parts included - (1) Driver Side Light Mount Bumper Bracket - (1) Passenger
More informationInstallation Manual for Philips SureSigns VS3/VS4/VM4/VM6/VM8/VSV VHM-25 Countertop Mount
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Manual for Philips SureSigns VS3/VS4/VM4/VM6/VM8/VSV VHM-25 Countertop Mount Install Time: 20-30
More informationInstallation Instructions
Installation Instructions AMP RESEARCH Power Step by Bestop Automatic Retracting Running Board Vehicle Application Nissan Titan King Cab 2004 and newer (5 ft.) Part Number: 75106-01 Nissan Titan Crew Cab
More information3PC TONNEAU COVER INSTALLATION INSTRUCTIONS. Ford Ranger/Mazda BT-50 (without bedliner)
3PC TONNEAU COVER INSTALLATION INSTRUCTIONS Ford Ranger/Mazda BT-50 (without bedliner) Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents.
More informationInstallation Instructions Supertop
INSTALLATION TIME Installation Instructions Supertop SKILL LEVEL Vehicle Application: Toyota Land Cruiser FJ40 1964 1984 Part Number: 51464 www.bestop.com - We re here to help! Visit our web site and click
More informationGENUINE CARGO NET INSTALLATION AND USER S INSTRUCTIONS
GENUINE CARGO NET INSTALLATION AND USER S INSTRUCTIONS Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read the
More informationFlip Top Installation Instructions
www.pavement-ends.com Flip Top Installation Instructions For: CJ7 1976-1986 Part Number: 44523 Wrangler/YJ 1986-1995 DO NOT INSTALL THIS PRODUCT ON ANY VEHICLE OTHER THAN THOSE LISTED ABOVE. WARNING This
More informationConvertible Top Installation Instructions
Convertible Top Installation Instructions For: Dodge Ramcharger, Part Number: 51318 Plymouth Trailduster 74-80 Congratulations on your purchasing decision. Bestop designed the Convertible Top to give you
More informationREF QTY PART DESCRIPTION PART NUMBER 1 1 Side Mirror, Driver (Not Shown) 1 Loctite - 263, 0.5 ml, Red Instructions
MIRROR KIT P/N 2881001, 2881002, 2881011, 2881012 APPLICATION em1400, em1400 LSV or M1400 BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain
More informationINSTALLATION INSTRUCTIONS: 2018 HARLEY-DAVIDSON SOFTAIL FAT BOY / BREAKOUT BIG RADIUS 2-2 PART# / 46075
INSTALLATION INSTRUCTIONS: 2018 HARLEY-DAVIDSON SOFTAIL FAT BOY / BREAKOUT BIG RADIUS 2-2 PART# 26075 / 46075 Congratulations, you have purchased the finest exhaust system available for your motorcycle.
More informationINSTALLATION INSTRUCTIONS
REV 3 05/13/2016 INSTALLATION INSTRUCTIONS PART NO. 702001T PRODUCT DESCRIPTION: FRONT INNER FENDER LINER APPLICATION: JEEP WRANGLER / WRANGLER UNLIMITED PRODUCT SAFETY & LEGAL DISCLAIMER IMPORTANT READ
More informationIMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
IMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE 2009 Toyota RAV-4 Stainless Steel Mesh Grilles L 30 G8P Fine Mesh Part #30-002-09 Quantity Description Part No. Upper Mesh Grille (includes):
More information2015 Mustang Lightbar (All Models) CDC#
2015 Mustang Lightbar (All Models) CDC# 1511-7000-01 Components: 1 CDC Lightbar Note: READ instructions before starting installation!!! CDC Part# Driver side bracket 0511-6001-05 Passenger side bracket
More informationINSTALLATION LIGHTED CURVED LAY DOWN LICENSE PLATE MOUNT 3166
INSTALLATION LIGHTED CURVED LAY DOWN LICENSE PLATE MOUNT 3166 PARTS INCLUDED 1 Lighted Curved Lay Down License Plate Assembly 1 Hardware Kit Including: 6 Cable Ties 1 Dielectric Grease Pack 1 1 x 8 Tape
More informationInstallation Instructions For: Suzuki Samurai, All Years Part Number: TM
Installation Instructions For: Suzuki Samurai, All Years Part Number: 51761 TM Patent Pending WARNING This product is designed to enhance the appearance of the vehicle and to shield the occupants from
More informationINSTALLATION INSTRUCTIONS
REV 3 05/13/2016 INSTALLATION INSTRUCTIONS PART NO. 702002T PRODUCT DESCRIPTION: REAR INNER FENDER LINER APPLICATION: JEEP WRANGLER / WRANGLER UNLIMITED PRODUCT SAFETY & LEGAL DISCLAIMER IMPORTANT READ
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PARTS LIST Accessory Application Publications No. MII 13038 GL1800 P/N 08E75-MCA-100K Issue Date November 2009 Honda Dealer: Please give a copy of these instructions to your customer.
More informationTOYOTA COROLLA HATCHBACK REAR SPOILER Preparation
Preparation Part Number: PT29A-12195-XX Kit Contents 1 1 Rear Spoiler 2 2 Hardware Bag Hardware Bag Contents 1 2 M6 Assembly Nuts 2 2 Grommet Inserts 3 1 Hole Plug Additional Items Required For Installation
More informationINSTALLATION INSTRUCTIONS AND OWNER S MANUAL
INSTALLATION INSTRUCTIONS AND OWNER S MANUAL Thank you for purchasing the AlloyCover from WeatherTech. Manufactured with pride using superior quality materials and workmanship. With proper care, your cover
More informationWWW. MOOSERACING.COM 1 / 8. INCLUDES EVERYTHING YOU NEED TO ADD MOUNTS TO YOUR MOTORCYCLE [KTM 1190 Adventure 2014 & up]
E x p e d i t i o n L u g g a g e Adventure Pannier Mount Set INCLUDES EVERYTHING YOU NEED TO ADD MOUNTS TO YOUR MOTORCYCLE 3501-0920 [KTM 1190 Adventure 2014 & up] Features of the Expedition Luggage -
More informationSPECIALTY TOP CO. STC. INSTALLATION INSTRUCTIONS TOYOTA FAST TRAC Z TOP Toyota FJ PART #222-31X 82 1/8" 82 1/8"
STC INSTALLATION INSTRUCTIONS TOYOTA FAST TRAC Z TOP Toyota FJ-40 1963-1983 PART #222-31X SPECIALTY TOP CO. Thank you for purchasing Specialty's Convertible Top for your Toyota. It has been designed for
More informationFEATURES OF THE EXPEDITION LUGGAGE - ADVENTURE PANNIER MOUNT SET:
E XPEDITION LUGGAGE ADVENTURE PANNIER MOUNT SET INCLUDES EVERYTHING YOU NEED TO ADD MOUNTS TO YOUR MOTORCYCLE 350-097 [Triumph Tiger 800; 20-204] FEATURES OF THE EXPEDITION LUGGAGE - ADVENTURE PANNIER
More informationINSTALLATION TURN SIGNAL MIRRORS 1432
1432 PARTS INCLUDED 1 Left Side Turn Signal Mirror Assembly with Convex Glass 1 Right Side Turn Signal Mirror Assembly with Convex Glass 1 Hardware Kit, Including: 2 5/16-18 X 1-1/2 Socket Head Cap Screws
More informationLexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2013-15 Lexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements Part #1372-0102-13 / Black Ice
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publication No. INSTALLATION INSTRUCTIONS 2 PIECE FOLDING POLY WINDSCREEN (OPTICAL) P/N 0SR72-HL3-100 SXS700M4/M2 Honda Dealer: Please give a copy of these instructions to your customer.
More information(2012 Production Onwards) INTEGRATED SIDE STEP INSTALLATION INSTRUCTION. 60 Minutes
NISSAN DUALIS (2012 Production Onwards) INTEGRATED SIDE STEP INSTALLATION INSTRUCTION Accessory Part No. STEP0004 60 Minutes Approx Product Weight: 15kg/33 lb IMPORTANT - PLEASE READ INSTRUCTIONS BEFORE
More informationTIP-OUT GLASS WINDSHIELD KIT
TIP-OUT GLASS WINDSHIELD KIT P/N 2881108 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationMustang Hood Scoop
Installation Instructions P/N: 421858 421859 421860 421861 421862 421863 421864 421865 421866 421867 421868 422055 422056 422057 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015-2017 Mustang
More informationVRSC-DX Truck-Lite LED Headlight Installation Instructions
VRSC-DX Truck-Lite LED Headlight Installation Instructions The following Instructions are for installing a 7 Truck-Lite LED headlight into a Harley Davidson VRSC-DX Night Rod Special fairing. Other 7 headlights
More informationOwner smanual. Banks Ram-Air Super-Scoop Chevy/GMC Pickups. with Installation Instructions
Owner smanual with Installation Instructions Banks Ram-Air Super-Scoop 2007-2013 Chevy/GMC Pickups THIS MANUAL IS FOR USE WITH SYSTEM 42235, 42236 & 42237 Gale Banks Engineering 546 Duggan Avenue Azusa,
More informationINSTALLATION & OWNER S MANUAL
Rev. C p. 1 of 21 INSTALLATION & OWNER S MANUAL F5205 HARD SIDED CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner when
More informationFord F-150 Billet Grilles Upper Replacement
2015-16 Ford F-150 Billet Grilles Upper Replacement Upper Black Billet Part #1045-019U-15B Upper Polished Billet Part #1045-019U-15 TOOLS REQUIRED Automotive grade masking tape, plastic clip removal tool,
More information(2) 10mm Quick Release Bolts with Pivot Washers (4) 10mm Flat Washers (2) 10mm Nylon Lock Nuts. (4) 10mm Plastic Washers
PARTS LIST: EXTREME GRILLE GUARD 1 Extreme Heavy Duty Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left Frame Mounting Bracket 4 10mm x 24mm OD x 2.2mm Flat Washers
More informationFEATURES OF THE EXPEDITION LUGGAGE - ADVENTURE PANNIER MOUNT SET:
E XPEDITION LUGGAGE ADVENTURE PANNIER MOUNT SET INCLUDES EVERYTHING YOU NEED TO ADD MOUNTS TO YOUR MOTORCYCLE 350-090 BMW R00/50GS: 999-2005 FEATURES OF THE EXPEDITION LUGGAGE - ADVENTURE PANNIER MOUNT
More informationGMC Yukon
Torch Series LED Grille TOOLS REQUIRED: Flat Head Screwdriver Long Flat Head Screwdriver Phillips Screwdriver 7mm Socket 10mm Socket Ratchet & Extensions 3/16 Drill Bit Power Drill Cutting Wheel or Saw
More informationFabric Replacement Top and Doors with Tinted Side and Rear Curtains Installation Instructions
Fabric Replacement Top and Doors with Tinted Side and Rear Curtains Installation Instructions For: Wrangler/TJ 1997-2002 Part Number: 51124 www.bestop.com DO NOT INSTALL THIS PRODUCT ON ANY VEHICLE OTHER
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 25852 PILOT Issue Date AUG 2003 PARTS LIST INSTALLATION NOTE: Door visor (Front left) These instructions show the left door visors being
More informationVHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm with Slide-In Mounting Plate
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com VHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm with Slide-In Mounting Plate (Refer to qualified
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory SADDLEBAG MOUNTING Application Publications No. Mll 13304-13660 BRACKET After 2007 VT750C Issue Date P/N 08L56-MEG-100E Revised: April 2011 Honda Dealer: Please give
More informationCAUTION: Do not install damaged parts!!!
Your satisfaction is important to us, please let us help! If you have any questions or concerns during the installation, our support representatives are available to assist you. Please call: 1-877-769-3765
More informationInstallation of Barricade Flat Style Fender Flare Kit (97-06 Wrangler TJ)
Installation of Barricade Flat Style Fender Flare Kit (97-06 Wrangler TJ) Installation Time: 3-4 Hours Tools Required: 8mm wrench 8mm socket drive #1 Phillips screw driver Pliers Pry bar Electric drill
More informationLOCKN LOAD MOUNTING KIT
LOCKN LOAD MOUNTING KIT TM VOLKSWAGEN AMAROK 2 BAR FIXED POINT HEAVY DUTY ROOF RACK SYSTEM MAX VEHICLE ROOF LOAD RATING: 100KG TOTAL LOAD EQUALS WEIGHT OF ROOF RACKS + ACCESSORIES + CARGO FIRST TIME INSTALLATION
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: SIDE WINDOW DEFLECTOR Nissan Rogue (2008) 999D3 GX000 KIT CONTENTS: Item Qty. Part Description Service Part Number A 1 Side
More informationINSTALLATION INSTRUCTIONS: INDIAN SCOUT HI-OUTPUT GRENADES PART# 18554/18654
INSTALLATION INSTRUCTIONS: INDIAN SCOUT HI-OUTPUT GRENADES PART# 18554/18654 Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your Vance & Hines exhaust is designed
More informationFEATURES OF THE EXPEDITION LUGGAGE - ADVENTURE PANNIER MOUNT SET:
E XPEDITION LUGGAGE ADVENTURE PANNIER MOUNT SET INCLUDES EVERYTHING YOU NEED TO ADD MOUNTS TO YOUR MOTORCYCLE 350-0898 [Triumph Tiger Explorer 200 202-204] FEATURES OF THE EXPEDITION LUGGAGE - ADVENTURE
More information