REAR DISCHARGE FINISHING MOWER

Transcription

1 REAR DISCHARGE FINISHING MOWER Operation and Parts Manual BFM BFM BFM-507 1

2 TO THE CUSTOMER This manual contains valuable information about your new mower. It has been carefully prepared to give you helpful suggestions for operating, adjusting and servicing. Keep this manual in a convenient place for quick and easy reference. Study it carefully, only by proper care and operation can you expect to receive the service and long life designed and built into this mower. It is the owner s and\or operator s responsibility to Read and understand the information contained in this manual. Operate, lubricate, assemble and maintain the equipment in accordance with all instructions and safety procedures in this manual. Inspect the equipment and replace or repair any parts that are damaged or worn which could cause damage, wear to other parts, or cause a safety hazard. 2

3 TABLE OF CONTENTS DESCRIPTION PAGE NUMBER Safety Instructions 4 Training Safety... 5 Starting And Stopping Safety. 6 Operation Safety 6 Transport Safety. 6 Service And Maintenance Safety.. 7 Storage Safety.. 7 Safety Signs.. 8 Torque Specifications... 9 Assembly Instructions 10 Attaching to the Tractor.. 12 Maintenance. 14 Trouble Shooting 16 Parts List 19 Warranty

4 SAFETY INSTRUCTIONS Good safety practices not only protect you, but also the people around you. Make these practices a working part of your safety program. Be certain that everyone operating this equipment is familiar with the recommended operating and maintenance procedures and follows all the safety precautions. Most accidents can be prevented. Do not risk injury or death by ignoring good safety practices. The alert symbol is used throughout this manual. It indicates attention is required and identifies hazards. Follow the recommended precautions. The safety alert symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! CAUTION The caution symbol indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. WARNING The Warning Symbol indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury, and includes hazards that are exposed when guards are removed. It may also be used to alert against unsafe practices. DANGER The Danger Symbol indicates an imminently hazardous situation that, if not avoided will result in death or serious injury. This signal word is to be limited to the most extreme situations, typically for machine components that, for functional purposes, cannot be guarded. 4

5 TRAINING SAFETY Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by a single careless act of an operator. In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper training of personnel involved in the operation, transport, maintenance and storage of equipment. It is the operator s responsibility to read and understand ALL Safety and Operating instructions in the manual and to follow them. Accidents CAN be avoided. Working with unfamiliar equipment can lead to careless injuries. Read this manual and the manual for your tractor before assembling or operating your mower, to acquaint yourself with the machines. It is the finish mower owner s responsibility if this machine is used by any person other than yourself, to make certain that the operator, prior to operating: Reads and understands the operator s manuals. Is instructed in safe and proper use. Know the controls and how to stop tractor, engine, and mower quickly in an emergency. Read this manual and the one provided with your tractor. Train all new personnel and review instructions frequently with existing workers. A person who has not read and understood all operating and safety instructions is not qualified to operate the machine, An untrained operator exposes himself and bystanders to possible serious injury or death. Do not allow children to operate this machine. STARTING AND STOPPING SAFETY Mower operating power is supplied from tractor PTO. Refer to your tractor manual for PTO engagement and disengagement instructions. Always operate the tractor PTO in the 540 rpm speed selection. DO NOT OVER SPEED! Know how to stop tractor and mower quickly in case of an emergency. When engaging PTO, the engine RPM should always be low. Once engaged and ready to start cutting, raise PTO speed to approx. 540 RPM and maintain throughout cutting operation. Always stop the tractor, set brake, shut off the tractor engine, remove the ignition key, lower implement to the ground and allow cutter blades to come to a complete stop before dismounting tractor. Never leave equipment unattended with tractor running or with implement in raised position. 5

6 OPERATION SAFETY The use of this equipment is subject to certain hazards which cannot be protected against by mechanical means or product design. All operators of this equipment must read and understand this entire manual, paying particular attention to safety and operating instructions, prior to using. If there is something in this manual you do not understand, ask your supervisor, or your dealer, to explain it to you. Most accidents occur because of neglect or carelessness. Keep all helpers and bystanders at least several hundred feet from an operating finish mower. Only properly trained people should operate this machine. When this machine is operated in populated areas or in other areas where thrown objects could injure persons or property, standard equipment safety chain shielding (which is designed to reduce the possibility of thrown objects) must be installed. Operation must be stopped when anyone comes within 100 yards(300feet). The majority of accidents involve entanglement on the driveline, injury of bystanders by objects thrown by the rotating blades, and operators being knocked off the tractor by low hanging limbs and then being run over by the mower. Accidents are most likely to occur with machines that are loaned or rented to someone who has not read the owner s manual and is not familiar with a finish mower. Check the tractor master shield over the PTO shaft. Make sure it is in good condition and fastened securely to the tractor. Purchase a new shield if old shield is damaged or missing. TRANSPORT SAFETY Review Transport Safety instructions in tractor manual before moving. Check with local authorities regarding transport on public roads. Obey all applicable laws and regulations. Make sure the SMV (Slow Moving Vehicle) emblem and all the lights and reflectors that are required by the local highway and transport authorities are in place, are clean, and can be seen clearly by all overtaking and oncoming traffic. Never have the equipment in operation during transport. Always travel at a safe speed. Inflate transport tires to recommended pressure. Do not drink and drive! 6

7 SERVICE AND MAINTENANCE SAFETY Stop engine, set brake, remove ignition key, and wait for all moving parts to stop before servicing, adjusting, repairing, or unplugging. Support the equipment with blocks or safety stands before working beneath it. Follow good shop practices including: - Keep service area clean and dry - Be sure electrical outlets and tools are properly grounded - Use adequate light for the job Use only tools, jacks, and hoists of sufficient capacity for the job. Replace and secure all shields removed during servicing before operating. Use heavy leather gloves to handle sharp objects. Failure to follow proper procedures when mounting a tire on a wheel or rim can produce an explosion, which may result in serious injury or death. Do not allow grease or oil to build up on any deck or platform. Where replacement parts are necessary for periodic maintenance and servicing, genuine factory replacement parts must be used to restore your equipment to original specifications. The manufacturer will not claim responsibility for use of unapproved parts and/or accessories and other damages as a result of their use. If equipment has been altered in any way from original design, the manufacturer does not accept any liability for injury or warranty. A fire extinguisher and first aid kit should be kept readily accessible while performing maintenance on this equipment. STORAGE SAFETY Following operation, or when unhooking, stop the tractor, set the brakes, disengage the PTO, shut off the engine and remove the ignition keys. Store the unit in an area away from human activity. Do not permit children to play on or around the stored machine. Make sure all parked machines are on a hard, level surface and engage all safety devices. Support the frame on stands and blocks to provide a secure base. 7

8 SAFETY SIGNS Keep safety signs clean and legible at all times. Do not paint over, remove or deface any safety signs or warning signs on your equipment. Observe all safety signs and practice the instruction on them. Replace safety signs that are missing or have become illegible. Replaced parts that displayed a safety sign should also display the current sign. Safety signs are available from your place of purchase. The safety signs used on the mower and their location are shown on the following sheet along with the part number for the safety signs

9 TORQUE SPECIFICATION For correct hardware tightening on the tiller, we suggest the use of suitable torque wrench and the applicable torque as listed in the table below: M-THREADED SCREW/BOLTS Bolt grade Thread Nm Lb-ft Nm Lb-ft M M M M M M M

10 ASSEMBLING Place the wheel supports (2) on the machine frame, and tighten the four bolts (4) with washers (5) and nuts (6). Insert the four wheels (1) in the support bushings, and adjust the cut height by means of the spacers (3). Skip the following step if Gearbox and Belts are already assembled on mower. Place the belts (7) onto the pulleys. Place the gearbox support (8) on the machine, insert both belts in the gearbox pulley guides (9), and tighten the four mounting bolts (10). Loosen the screws (11) and adjust the belt tensioning by means of the adjustment screw (12); finally tighten the four screws (11). 10

11 Place the covers (13) on the belts, tighten the handles on the frame (14) and on the gearbox support (15). Anchor the PTO shield (16) by means of four screws (17) and the washers (18). I Install the uprights (19) on the machine and insert the bolts (21), and relative nuts (22). Install the tie -rods (20) on the machine and insert the bolts (23), with relative nuts (24). Place the top link (25) on both tie-rods and uprights, by inserting the spacer (26) between the top link and the tie-rods; finally tighten the screw (27) with the nut (28) and the washer (29). Make sure that the top link turns freely on the bolt. Finally tighten the bolts (21) with the nuts (22) and the bolts (23) with the nuts (24). Install the lower hitches (30) on the supports (31); adjust the length and install the pins (32) anchoring them by means of the split pins (33). 11

12 ATTACHMENT TO THE TRACTOR Carefully read this instruction manual and the manuals of the tractor and PTO shaft manufacturer. All mowers are built to be attached to any tractor equipped with a three-point lift of the correct category and with suitable ball ends. Before attaching the equipment to the tractor, make sure that the ground is smooth and flat and that nobody is standing between the tractor and the mower; slowly move the tractor towards the mower by aligning the tractor lifter arms with the two mower coupling side pins; turn the engine off and pull the brake. It is possible to adjust the attachment position by releasing the pins A (picture 1) and modifying the position of the plates B. picture 1 Connect the tractor top link to the third upper point by removing the pin located between the two plates, inserting the top link and securing it by means of the pin. Adjust the top link so that the upper part of the frame is parallel to the ground. Block all the linking parts by means of the sway chains or arms. Make sure that the central unit axis (case/bevel gear pair) is parallel to the ground, thus minimizing the stresses on the power take off and increasing the working life of the equipment. Before installing the PTO shaft make sure that the RPM rating and the direction of rotation match those of the tractor. Carefully read the PTO shaft and tractor instructions. Furthermore, accurately read the instructions of the manufacturer of the PTO shaft and of the tractor. Before starting any activity, make sure that the guards are installed on the power take off of the tractor and PTO shaft. Make sure that they cover the PTO shaft throughout its length. Shortening a PTO Driveline 1. With the implement attached to the tractor s three point hitch, and the PTO driveline not installed, separate the PTO driveline. Attach the implement end to the implement and the other end to the tractor PTO input shaft. 2. Raise the implement by using the tractor s hydraulic 3-point hitch to it s maximum lift height. 3. Hold the half shafts next to each other and mark them so each end is approximately ½ from hitting the end of the telescopic profiles. 4. Shorten the inner and out guard tubes equally. 5. Shorten the inner and outer profiles by the same length as the guard tubes. Using a rattail file, round off all sharp edges and burrs. Grease the telescopic profile generously before reassembling. CAUTION When fully extended, the plastic pipes must overlap by at least 1/3 of the length of the pipes (LT). When retracted, the min. acceptable clearance is 1-2 cm. 12

13 CUTTING HEIGHT ADJUSTMENT The cutting height of the equipment depends on the position of the wheels. If the wheels are raised, the cutting height increases; if the wheels are lowered, the cutting height decreases. Make sure that the wheels are set at the same height on both sides. To adjust the cutting height on the mowers loosen and remove pin A and adjust the wheels height according to the bushing B. When the adjustment is completed, reinsert the pin A. In the mowers it is necessary to adjust the belt tension as they stretch; the correct belts tensioning ensures that the machine works correctly. To adjust the belts tension: Remove the two Belt Shields (A). Loosen the Nuts (B) holding the gearbox in place just enough to allow the gearbox to be able to move. Turn the bolt C to adjust the tension of the belts; if you turn the bolt in clockwise direction the belts are tightened, while turning it counter clockwise they are loosened; when the belt is tensioned correctly the belt should be able to deflect a maximum of 10 mm (3/8 ). Retighten the Nuts (B). Replace Belt Shields (A). C B A DANGER These activities must be carried out with the engine off, the power take off disengaged and the hand brake applied. If needed, lift the equipment and place it on supports, thus preventing any injuries that might be caused by a sudden fall of the equipment. 13

14 MAINTENANCE Maintenance is crucial for the working life and efficiency of any agricultural equipment. If the equipment is properly maintained and operated, a long working life and operator safety are assured. The maintenance intervals indicated in this booklet are provided as a mere reference and are related to normal working conditions; changes may occur depending on the type of activities, environmental dust, seasonal factors, etc. First check after 50 working hours, check the oil in the gearbox (A picture 7) and make sure that all the screws and bolts are tightened. Before injecting lubricating grease into the grease fittings, clean the fittings to prevent mud, dust, or any other foreign matter from contaminating the grease and reducing the lubrication effect. CAUTION When adding or changing the oil, use the same type of oil to prevent mixing oils with different features. All maintenance activities must be carried out with the tiller resting horizontally on the ground, with the engine off and not overheated. After using the equipment for a few hours, make sure that all the bolts (especially tine bolts) are tightened; regularly check all the machine guards. 14

15 Every 20 working hours lubricate the pulley support bearing (C ). Every 30 working hours check belt tensioning. Every 40 working hours lubricate the wheel supports (A picture 8). After the first 50 working hours and, later, every 800 working hours replace the oil in the gearbox. Use oil SAE EP 80W90. BLADE REPLACEMENT For perfect machine operation, frequently check the mower blades: make sure that they are sharp and are always held tight by the 12mm bolt or the 18mm lock nut. Follow the procedure below to replace the blades: Take any and all measures to prevent accidental machine start-up. Place the equipment on sturdy supports. Remove the bolt and washer by turning it counter clockwise holding the blades as shown in picture; remove the old blades and install the new ones, Torque nut to 250 ft/lbs or 12mm bolt to 104 ft/lbs. DANGER Before replacing the blades, turn the tractor engine off, pull the parking brake, disengage the power take off, raise the mower using the tractor lift, and install supports to prevent accidental dropping of the machine. 15

16 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Streaking Grass discharges from mower unevenly or bunches along a swath Heavy vibration Slow blade tip speed Worn blade tips Dull blades Blades unable to cut the part of grass pressed down by tractor s tire path or mower s casters Mowing too fast Drive belt loose Belt glazed/slipping Blade loose on spindle Conditions too wet for mowing Grass is too high and too coarse Belt Slipping Grass is wet Blade speed is too fast Broken/bent blade Worn/unbalanced blade Bent/broken sheave Operate PTO at 540 RPM Replace with correct specified blades Sharpen blades uniformly Slow tractor s ground speed but maintain 540 RPM PTO speed Slow down until cured Tighten per instructions on maintenance chapter Apply belt dressing or replace it with a correct specified belt. Tighten blade nut securely. Allow grass to dry before mowing Slow tractor s ground speed but maintain 540 RPM PTO speed. Raise the mower for the first pass and lower to the desired cutting height for the second and cut at 90 degrees to the first pass. Raise the rear of mower high enough to allow the grass to discharge, but not too high for streaking to occur. Tighten belt to replace with a correct specified belt. Allow grass to dry before mowing. Slow tractor s ground speed but maintain 540 RPM PTO speed. Cut the grass at a lower height Do not exceed 540 RPM PTO speed Replace with correct specified blade Grind blade uniformly or replace Replace with correct specified part Debris caught on blade Belt loose Clean off blade Tighten or replace with correct specified belt Belt slipping Belt glazed Use belt dressing or replace it Oil on belt Clean or replace. 16

17 PROBLEM POSSIBLE CAUSE SOLUTION Mower is overloading, grass is too tall or heavy Slow tractor s ground speed but maintain 540 RPM PTO speed. Cut the grass twice. Raise the mower for the first pass and lower to the desired cutting height for the second and cut at 90 degrees to the first pass. Cut a partial swath only Belt slippage (cont.) Oil on belt from over lubrication Clean lubricant from belt and sheaves with a clean rag,replace oil soaked belts. Be sure to follow operator s manual recommendations. Belt hung or rubbing Check belt for free travel in sheaves. Check under mower deck and spindles for debris or other foreign material and remove if any is present Belt rollover Damaged belt Belt breakage Blade is scraping ground Gearbox overheating Gearbox leaking Damaged belt Foreign object in sheave groove Worn sheave groove Rollover, high shock loads or installation damage High shock loads Belt came off sheave Mower too low Field is ridged Field is too wet Low on lubricant Improper type lubricant Excessive trash build-up around gearbox Damaged oil seal Bent shaft Shaft rough in oil seal area Oil seal installed wrong Oil seal not sealing in the housing Oil level too high 17 Replace it with correct specified belt Inspect all sheave grooves for rust, paint or other foreign material. Remove these if present Replace with correct specified sheave. Replace it with correct specified belt Avoid hitting ground and large obstructions with the mower. Check sheave for proper alignment and foreign material. Ensure proper belt tension. Avoid hitting the ground and large obstructions with mower. Raise mower-reset wheels Cut field at a different angle Stop and wait until is dried Fill to proper level Replace with proper lubricant Remove trash Replace seal Replace oil seal and shaft Replace or repair shaft Replace seal Replace seal or use a sealant on outside diameter of seal Drain oil to proper level

18 PROBLEM POSSIBLE CAUSE SOLUTION Gearbox leaking (Cont.) PTO contacts mower front frame when raised Gearbox noisy Blades wear too fast Mower seems to require excessive power Hole in gearbox Gasket damaged Bolts loose Raising mower too high or incorrect adjustment of tractor top link Worn bearings Low oil in gearbox Cutting in sandy conditions Cutting in rocky conditions Blades hitting ground Advancing into grass too rapidly Hitting ground Worn or dull blades Tractor not large enough Grass wet Replace gearbox Replace gasket Tighten bolts Adjust top link or tractor lift stops Replace bearings Check level and add oil Increase cutting height Increase cutting height. Remove rocks Increase cutting height Reduce forward travel speed Raise mower and reset wheels Sharpen or replace blades Use larger horsepower tractor Allow grass to dry before mowing Grass too tall and heavy Slow ground speed of tractor but keep engine running at full PTO rpm. Make two passes. Raise mower for first pass and lower for next pass. Mower moves from side to side when cutting Loose tractor sway chains or bars, or sway blocks improperly installed Adjust sway, bars, or sway blocks 18

19 Parts Breakdown 19

20 Finishing Mower BFM BFM BFM

21 Finishing Mower BFM BFM BFM-507 Pos. Part # Description Qty 1 FM10060 Input shield 1 2 OS Oil Seal 35 x 72 x SRE7200 Snap Ring Ext.Φ FM50004 Shim 1 5 B6207 Bearing FM50006 Input Shaft 1 7 KM Key 10 x 8 x FM50008 Ring Gear 1 9 B30207 Bearing BM Bolt Metric 8 x FM50011 Housing 1 12 Oil plug Oil Plug16X BM Bolt Metric 8 x FM50014 Cap - Gearbox 1 15 FM50015 Gasket - Gearbox Cap 1 16 FM50016 Sight Plug M14x BM Bolt 12 x FM50018 Output Shaft 1 19 B32008AX Bearing 32008AX 1 20 KM Key 10 x 8 x FM50021 Spacer - Pinion Gear 1 22 FM50022 Shim- Pinion Gear 1 23 B30208 Bearing OR40265 Oil Ring 40 x FM50025 Bevel Pinion Spacer 1 26 OS Oil Seal 50 x 80 x LNM40150 Lock nut 40 x FM50028 Stop Washer 1 29 BM Bolt 12X FM50030R-60 Belt Cover - BFM-505 Right 1 FM50030R-72 Belt Cover- BFM-506 Right 1 FM50030R-84 Belt Cover- BFM-507 Right 1 30A FM50030L-60 Belt Cover- BFM-505 Left 1 FM50030L-72 Belt Cover- BFM-506 Left 1 FM50030L-84 Belt Cover- BFM-507 Left 1 31 BM Bolt M8X FM50032 Gearbox Plate 1 33 FM50033 Gearbox Support Plate 1 34 BM Bolt 10 x BM Bolt 10 x

22 Finishing Mower BFM BFM BFM

23 Pos. Part # Description Qty 36 BM Bolt 10 x A FM50036A Dust Cap 3 37 Lynch Pin Φ FM50038 Hitch Block 2 39 FM50039 Lower Hitch Pin 2 40 FM50040 Pivot Hitch Pin 4 41 BM Bolt M12X FM Deck - 60" 1 FM Deck - 72" 1 FM Deck - 84" 1 43 Lynch pinφ FM50044 Spacer - Cutting Height 1 1/4" 4 45 FM50045 Bushing Wheel Arm 4 46 FM5046 Spacer - Cutting Height 1" 4 46A FM50046A-60 Wheel Arm - BFM FM50046A-72 Wheel Arm - BFM FM50046A-84 Wheel Arm - BFM FM50047 Spacer - Cutting Height 5/8" 4 48 FM50048 Spacer - Cutting Height 1/2" 4 49 FM50049 Spacer - Cutting Height 1/4" 4 50 FM50050A Wheel Yoke - BFM-505 & BFM FM50050B Wheel Yoke - BFM Y Tire - Hard Tire 250 X 85 (BFM-505 & BFM-506) Tire - Hard Tire 310 X 100 (BFM-507) 4 52 FM50052 Spacer - Hard Tire 250 X 85 (BFM-505 & BFM-506) 8 FM50052 Spacer - Hard Tire 310 X 100 (BFM-507) 53 B6205-2RS Bearing RS FM50054 Bushing - Hard Tire 250 X 85 (BFM-505 & BFM-506) 4 FM50054A Bushing - Hard Tire 310 X 100 (BFM-507) 55 BM Bolt M12X130 (BFM-505 & BFM-506) 4 BM Finishing Mower BFM BFM BFM-507 Bolt M12X165 (BFM-507) 56 GN08100 Grease Fitting M8X NM25150 Lock Nut M25X FM Single Pulley 2 59 FM V-BELT BFM-505 (B67 17 x 1727) 2 FM V-BELT BFM-506 (B74 17 x 1880) 2 FM V-BELT BFM-507 (B82 17 x 2083) 2 60 BM Bolt M10X

24 Finishing Mower BFM BFM BFM

25 Finishing Mower BFM BFM BFM-507 Pos. Part # Description Qty 61 FM50061 Spindle Hub 3 62 FM50062 Spacer 3 63 FM50063 Spindle Shaft (Threaded for Nut) 3 FM50063A Spindle Shaft (Threaded for Bolt) 3 64 KM Key 8x8x FM50065 Dust Cover Gasket 3 66 FM50066 Dust Cap 3 67 FM50067 Plate - Blade 3 68 FM Blade - BFM FM Blade - BFM FM Blade - BFM LNM18150 Lock Nut 18 x FM50069 Bolt Blade M12 x 1.25 x 25 Grade FM Double Pulley 1 71 FM Drive Pulley- BFM FM50071 Drive Pulley - BFM-506 & BFM FM50072 A Frame Support (BFM-505 & BFM-506) 2 FM50072A A Frame Support (BFM-507) 2 73 FM A Frame Strap (BFM-505) 2 FM A Frame Strap (BFM-506) 2 FM A Frame Strap (BFM-507) 2 74 BM Bolt M12X FM50075 Top Link 1 76 FM50076 Top Hitch Pin 1 76A FM50077 Spacer - Top Link 1 77 BM Bolt M12X

26 26

27 LIMITED WARRANTY Belco Resources Equipment warrants to the original purchaser of any new piece of machinery from Belco Resources Equipment, purchased from an authorized Belco Resources Equipment dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-commercial, state, and municipalities use, ninety (90) days for commercial use from date of retail sale. Warranty for rental purposes is thirty (30) days. The obligation of Belco Resources Equipment to the purchaser under this warranty is limited to the repair or replacement of defective parts. A four (4) year extended Gearbox Limited Warranty is provided for certain models at the end of the standard one (1) year warranty period. This warranty is not provided for commercial or rental uses. The extended warranty provides for the replacement of parts only. Not covered are oil seals or any damages to the gearbox due to lack of lubrications. Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety (90) days from the date of purchase of such part or to the expiration of the applicable new equipment warranty period, whichever occurs later. Warranted parts shall be provided at no cost to the user at an authorized Belco Resources Equipment dealer during regular working hours. Belco Resources Equipment reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship. This limited warranty does not apply to and excludes wear items such as shear pins, tires, tubes knives, blades or other wear items. Oil or grease is not covered by this warranty. All obligations of Belco Resources Equipment under this limited warranty shall be terminated if: Proper service is not preformed on the machine The machine is modified or altered in any way. The machine is being used or has been used for purposes other than those for which the machine was intended. DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES Belco Resources Equipment obligation under this limited warranty, to the extent allowed by law, is in lieu of all warranties, implied or expressed, including implied warranties of merchantability and fitness for a particular purpose and any liability for incidental and consequential damages with respect to the sale or use of the items warranted. Such incidental and consequential damages shall include but not be limited to: transportation charges other than normal freight charges; cost of installation other than cost approved by Belco Resources Equipment; duty; taxes; charges for normal service or adjustment; loss of crops or any other loss of income; rental of substitute equipment, expenses 27

28 Increasing agricultural productivity since 1974 Belco Resources Equipment P.O. Box 8164 Rocky Mount, NC Tel: Fax: