Toll Free (877) - ICFLUID

Transcription

1

2 Introduction AEGI brackets are a sensible and easy way of securing piping and hoses in all type of industries and on all types of terrestrial or naval installations. AEGI brackets characteristics are: pleasent, practical and economical design using weldable plates or conduits, it s easy to anchor the brackets to machinery and steelwork. fast, safe, economic installation and service in piping systems AEGI standard brackets are manufactured in: Polypropylene - green color - for standard, heavyduty and double series Polyamide - black color - (Nylon 6-6 loaded with 20% of glass fibre self-extinguishing VO) for standard, heavy duty and double series Aluminum for heavy-duty series The other metallic components of the clamps are manufactured in: Lower and upper plate: Steel ASTM Bolt: Steel Grade 5 Rail: Steel ASTM - A336 19ga. Nuts: ASTM - A570 NOTE: STANDARD Rail are painted green. Mounting details Weld plate mounting Adjust weld plates and position with locating magnets or clips. Weld the plate on. Press the lower clamps, lay the tube, put on second halves of the clamp and tighten screws. Don t weld with plasticclamps on them! Long weld plates can be screwed directly to the surface. Pay attention to the bracings (under no circumstances may the two halves of the clamps be in contact with each other). Rail mounting Mounting rails are supplies in 3 or 6 pieces. Weld or screw on the mounting rail with the nut. Insert the nut into the rail and turn as far as the stop (at correct spacing). Press on the lower clamp, lay the tube put on the second clamp half, tighten up. Pay attention to the bracings (under no circumstances may the two clamp halves be in contact with each other). Stacking Consists of 2 clamp halves, stacking bolt(s) and a bolt locking plate. To construct a stack, fasten a weld plate or rail nut and locate 2 clamp halves and tube, securing with stacking bolt(s). Once tight, these bolts must be held with a locking plate. The next clamp can then be assembled and so on, until the stack is complete, the last clamp being secured with conventional bolt(s) and top plate. For each stack, a mounting shape of your choice should be ordered, components from which start and finish the stack. We reserve the right to make modifications in the interest of technical progress. -2-

3 TABLE OF CONTENTS DESCRIPTION PAGE NO. Standard Series Assemblies... 4 Twin Series Assemblies... 5 Heavy-Duty Series Assemblies Standard Series Parts... 8 Twin Series Parts... 9 Heavy-Duty Series Parts Additional Standard Series Parts Terms and Conditions IC Fluid Power accepts Visa and Mastercard -3-

4 STANDARD SERIES CLAMPS POLYPROPYLENE DIAMETER CLAMP SETS CLAMP ASSEMBLIES -4-

5 TWIN SERIES CLAMPS POLYPROPYLENE DIAMETER CLAMP SETS CLAMP ASSEMBLIES -5-

6 HEAVY DUTY SERIES CLAMPS POLYPROPYLENE DIAMETER CLAMP SETS CLAMP ASSEMBLIES -6-

7 HEAVY-DUTY SERIES CLAMPS POLYPROPYLENE DIAMETER CLAMP SETS CLAMP ASSEMBLIES -7-

8 STANDARD SERIES CLAMP PARTS -8-

9 TWIN SERIES CLAMP PARTS -9-

10 HEAVY-DUTY SERIES CLAMPS PARTS BY REQUEST ONLY BY REQUEST ONLY -10-

11 ADDITIONAL STANDARD SERIES CLAMP PARTS Net 30 day terms apply after credit has been established F.O.B. Rossford, Ohio U.S.A. IC Fluid Power, Inc. warrants the products listed in this catalog for a period of six (6) months after shipment. Products shall be free from defects in material and workmanship for a period of six (6) months after shipment. If the product purchased is defective in any way during the six (6) month period, please contact IC Fluid Power, Inc. for an RGA number to return the product for a full evaluation. If the product is defective, IC Fluid Power, Inc. will replace the product at no charge to the customer. This comprises the entire warranty and IC Fluid Power, Inc. makes no other claim whatsoever. See IC Fluid Power, Inc. seperate written warranty. IC Fluid Power, Inc. will not accept back any product without first issuing an RGA number. The RGA number must appear on all paperwork. If product is being sent back for any other reason than product defect, a 20% restocking charge will be deducted from the credit. Product being sent back for credit must be in re-saleable condition and the freight must be prepaid. A 50% restocking charge applies to product originally sent via air freight or expedited service. Credit balances can be offset by material purchases only. Cash payments are not allowed. IC Fluid Power, Inc. carries product liability insurance and will provide a copy at your request. Errors in shipping or billing must be reported within 10 days of receipt of order. IC Fluid Power, Inc. clamps are manufactured to conform with DIN specifications. -11-

12