IEC Contactors & Starters XT IEC Power Control

Transcription

1 July Contents Description Page umber Selection Product Selection Accessories Technical Data and Specifications Dimensions Reference Data Frame Pushbutton -Frame Rotary Product Description D-Frame Eaton s new XT family of Manual Motor Protectors (MMPs) features a pushbutton or rotary O/OFF manual disconnect, Class adjustable bimetallic overload relay and fixed magnetic short circuit trip capability in one compact unit. Two frame sizes are available: Frame ( mm) for motors with FLA ratings up to A and Frame D ( mm) covers motor FLA ratings up to 6A. Application Description The XTP and XTPR MMPs can be used in the following applications. Motor Protective Circuit reaker In many countries outside of the United States and Canada, especially Europe, the MMPs are tested and classified as thermal magnetic circuit breakers for use in motor branch circuits. This can be an important consideration for all companies who export their equipment and machines internationally. oth the XTP and XTPR conform to IEC/E 6097 and have the CE Mark. The XTP and XTPR MMPs are UL Listed under UL 8 as. They provide an economical solution for applications requiring simple manual starting and stopping of motors. When used as an MMP, they are typically installed in an enclosure. Many enclosures are offered as accessories for the MMPs. Separate short-circuit protective devices, such as circuit breakers or fuses, are wired ahead of the MMPs. The short-circuit protective device should be sized per the EC code and should not exceed 00% of the maximum FLA dial setting of the MMP. Group Motor Installations A Group Motor Installation can be defined as more than one motor circuit protected by a single set of fuses or circuit breaker on a motor branch circuit. This eliminates the need for individual fuses or circuit breakers for each motor circuit. Substantial component cost savings, panel space savings and reduced wiring installation time can be achieved in Group Motor Installations. The MMPs are tested and listed for group installation. If remote operation is required, a magnetic contactor can be wired in series with the MMP. See Figure -9. Article 0. of the ational Electric Code contains the rules and requirements for Group Motor Installations. Refer to Application ote AP0000E for EC requirement for group motor installation. To Supply XTPR Disconnect Fuses XTPR XTPR Or Circuit reaker Manual Motor Protector Magnetic Contactor (Used for Remote Control) Motors Figure -9. Group Motor Installation EC 0- See Application ote AP0000E. Protection in Different Controller Types A UL 8 Type E Self-protected Manual Combination Starter/Motor Controller consists of a single device having integral short circuit protection, a main set of contacts, motor overload protection, and July also include a UL listed Line Side Adapter (See Figure -96). This type of controller is a legitimate short circuit protective device and disconnect means for the downstream motor. It does require an upstream feeder short circuit protective device, but does not require a dedicated branch circuit protection or a disconnect means. A UL 8 Type E rating means that the unit clears a fault and does not experience any welding of the power poles. A UL 8 Type E self-protected manual combination starter will remain fully functional should a short circuit within its ratings occur. A UL 8 Type F Self-protected Combination Motor Controller consists of a UL 8 Listed Type E Self-protected Manual Combination Starter/Motor Controller, a UL Listed Contactor, and possibly a UL Listed Line Side Adapter. While the Type E self-protected manual motor controller of this combination motor controller device is a legitimate short circuit protective device and disconnect means for the downstream motor, the contactor is not self-protected. E.g. XTCE007 XTCE06. In addition, as a complete assembly or modular components, the device should have Type Coordination certification. Type Coordination means the Starter or the Controller must exhibit little or no damage following a major short circuit fault and should be able to be returned to proper service without replacing any parts. Component in a Combination Motor Controller The XTP and XTPR MMPs can also be wired in series with a magnetic contactor to complete the assembly of a remotely operated, combination motor controller. CA0800K

2 - July 008 Features O/OFF Rotary Handle with Lockout Provision Visible Trip Indication Class Overload Protection Phase Loss Sensitivity Ambient Temperature Compensation to IEC/E 6097, VDE 0660 Fixed Short Circuit Trip times maximum setting of overload FLA dial Type Coordination per IEC 97 Identification Markers Standard on Starter Faceplate Motor Applications from 0.A to 6A uilt-in heater and magnetic trip elements to protect the motor Adjustment dial for setting motor FLA DI Rail Mount Terminal Types Available: Screw terminals Screw (line) and Spring Cage (load) terminals Spring Cage terminals Accessories include: Front and Side Auxiliary Contacts Trip Indicating Contacts Tamperproof Cover for OLR Dial Undervoltage Release Shunt Trip Thru-the-Door Operators Enclosures -Phase Line Side Connecting Links Group Installation Using the in-panel Main SCPD. Line Side Adapter (LSA) ot required Line Side Adapter Figure -96. Line Side Adapters When to Use Them ote: Line Side Adapters are not required for non-us applications. Most countries outside of the US classify the MMP as a thermal magnetic circuit breaker. Standards and Certifications UL Listed File o. E98 UL 8 Group Motor and Type E Compliant IEC/E 6097 CSA File 9767, Class -0 DI VDE 0660 Part 0, Part and Part CCC ote: For Type Coordination of MMCs, see Tables -90 through -9 on Pages -6 and -6. Self-Protected Manual Combination Starters UL 8 Type E Self-Protected Manual Combination Starter Only Upstream Feeder SCPD required no dedicated in-panel Main SCPD for MMP. Line Side Adapter MMP XTPR C Line Side Adapter (LSA) Required Types (Configurations) Line Side Adapter D MMP XTPR DC Motor Protective Device with Thermal and Magnetic Trip XTP Pushbutton Actuated Manual Motor Protector up to A XTPR Rotary Actuated Manual Motor Protector up to 6A For the Protection of Transformers with a high inrush current: XTPT Manual Transformer Protector up to A not UL Approved Motor Protective Device without Overload Function: XTPM Motor Protective Circuit reaker up to A not UL Approved CA0800K

3 July Table -. Product Identification o. Description Page asic Units XTP Pushbutton Manual Motor - Protectors: Rated operational current up to A Switching capacity ka/v Short circuit release, fixed setting to x I u Overload release, adjustable 0.6 x I u Single-phasing sensitive XTPR Rotary Manual Motor Protectors: Rated operational current up to A, 6A Switching capacity / ka/ V Short circuit release, fixed setting to x I u Overload release, adjustable 0.6 x I u Single-phasing sensitive With screws or spring-loaded terminals - Mounting Accessories Rotary Handle Mechanism: - O/OFF/Tripped switch position indication Lockable with padlocks Integrated door/cover interlock Extendable by plug fit extension shaft Handle latched in switch positions Optionally also without locking and door interlock function Insulated Enclosures: -6 Surface mounting enclosures, IP0, IP and IP0 and IP front flush mounting enclosure Mounting/Wiring: Component adapter for busbar mounting Three-phase commoning link for side-by-side mounting Mounting kits for rapid mounting of direct-on-line, reversing and star-delta starters - Add-On Functions Voltage Releases: -0 Undervoltage release Shunt release With screws or spring-loaded terminals Standard Auxiliary Contacts: -8 O/OFF indication Differential fault indication overload/short circuit release O/OFF for (high capacity) contact module O/OFF for starter combination With early-make contacts With screws or spring-loaded terminals 6 Current Limiter: Increases the switching capacity of the A to 0 ka/0v Can be used for individual group protection -0 CA0800K

4 - July 008 XTP -Frame XTPR, XTPM and XTPT -Frame XTPR D-Frame umber Selection Table -. XT umbering System X T P R 0 C Designation XT = Type P = Manual Motor Protector Pushbutton PR = Manual Motor Protector Rotary PM = Manual Motor Protector Magnetic Only PT = Manual Transformer Protector (High Mag.) Current Ratings Frame P6 = 0.6A P = 0.A P0 = 0.0A P6 = 0.6A 00 = A P6 =.6A P =.A 00 = A D Frame 06 = 6A 0 = A 0 = A 00 = 0A Trip Class C = Class lank = Magnetic only (o thermal trip) Frame Size = mm D = mm 6P = 6.A 0 = A 0 = A 06 = 6A 00 = 0A 0 = A 0 = A 0 = A 08 = 8A 06 = 6A CA0800K

5 July Product Selection Product Selection for Manual Motor Starter Applications When ordering, specify umbers according to the following stipulations: XT are selected based on the overload current range required for a given motor. This current range is determined from the motor Full Load Ampere rating and Motor Service Factor usually found on the motor nameplate. For motors with service factors less than., multiply the motor FLA by.90 to select appropriate MMP. Example: For motor having FLA of 6.A and service factor of.0 (6.A x.90 =.76A) select umber XTP6P0. See Application ote AP0000E. For motor with service factor of. or greater, use motor nameplate Full Load Amperes to select the appropriate MMP. Example: For motor having FLA of A and service factor of., select umber XTPR0C. -Frame Table -. XTP Pushbutton Global and orth American Ratings Type and Type Coordination Motor Protective Device with Thermal and Magnetic Trip Rated Uninterrupted Current I u = I e (Amps) FLA Adjustment Range / Overload Release I r (Amps) Short Circuit Release I rm (Amps) Maximum Motor Ratings Maximum kw Rating AC- P (kw) -Phase 0 0V 80 V 0V 0V V Maximum hp Rating P (hp) UL 8/CSA C. o. -Phase 00V 0V 80V V Screw Terminals umber Frame Select by full load amperes. Maximum Motor Ratings (kw, hp) are for reference only. In this range, calculate motor rating according to rated current. Specified values to EC Table 0.. otes: Single-phasing sensitivity to IEC/E , VDE 0660 Part. Can be snap-fit to IEC/E 607 top-hat (DI) with 7. or mm height. Service Factor (SF) Setting I r of current scale in dependence of load factor: SF =. -> I r = x I n mot SF = -> I r = 0.9 x I n mot For manual motor protective circuit breaker switching capacity, see Page / -/ / -/ 7-/ / / 7-/ 7-/ / -/ 0 XTPP6C XTPPC XTPP0C XTPP6C XTP00C XTPP6C XTPPC XTP00C XTP6PC XTP0C XTP0C XTP06C XTP00C XTP0C Technical Data Page -0 Discount Symbol MC7 CA0800K

6 - July 008 -Frame D-Frame Table -6. XTPR Rotary with Screw Terminals Global Ratings and orth American Ratings Type and Type Coordination Motor Protective Device with Thermal and Magnetic Trip Rated Uninterrupted Current I u = I e (Amps) FLA Adjustment Range / Overload Release I r (Amps) Short Circuit Release I rm (Amps) Maximum Motor Ratings Maximum kw Rating AC- P (kw) -Phase 0 0V 80 V 0V 0V V Maximum hp Rating P (hp) UL 8/CSA C. o. -Phase 00V 0V 80V V Screw Terminals umber Frame Frame D Select by full load amperes. Maximum Motor Ratings (kw, hp) are for reference only. In this range, calculate motor rating according to rated current. Specified values to EC Table 0.. number shown comes with screw terminals. For Frame devices up to 6A, spring cage terminals are available. For spring cage terminals on line and load sides, insert a C into the number in the th position Example: XTPRC_C. For spring cage terminals on the load side only, insert an SC into the number in the th and 6th positions Example: XTPRSC_C. otes: Single-phasing sensitivity to IEC/E , VDE 0660 Part. Can be snap-fit to IEC/E 607 top-hat (DI) with 7. or mm height. Service Factor (SF) Setting I r of current scale in dependence of load factor: SF =. -> I r = x I n mot SF = -> I r = 0.9 x I n mot For manual motor protective circuit breaker switching capacity, see Page / -/ 7-/ 7-/ / -/ 7-/ 7-/ / / 7-/ 7-/ / -/ XTPRP6C XTPRPC XTPRP0C XTPRP6C XTPR00C XTPRP6C XTPRPC XTPR00C XTPR6PC XTPR0C XTPR0C XTPR06C XTPR00C XTPR0C XTPR0C XTPR06DC XTPR0DC XTPR0DC XTPR00DC XTPR0DC XTPR08DC XTPR06DC Technical Data Page -0 Discount Symbol MC7 CA0800K

7 July Frame D-Frame Table -7. XTPR Manual Self-Protected Motor Starters orth American Ratings, UL 8 Type E Motor Protective Device with Thermal and Magnetic Trip Rated Uninterrupted Current I u (Amps) FLA Adjustment Range / Overload Release I r (Amps) Short Circuit Release I rm (Amps) Maximum Motor Ratings Rated Short-Circuit reaking Capacity (ka) Maximum hp Rating P (hp) 0V 80/ / -Phase 77V 7V 00V 0V 80V/ 77V V/ 7V Line Side Manual Motor Adapter Protector Screw Terminals umber umber Frame Frame D / -/ 7-/ 7-/ / -/ 7-/ 7-/ / / 7-/ 7-/ 0 0 / -/ Select by full load amperes. Maximum Motor Ratings (kw, hp) are for reference only. In this range, calculate motor rating according to rated current. Specified values to EC Table 0.. UL 8 Type E starters are assembled from a standard XTPR and a special incoming terminal Line Side Adapter ( or D). otes: A UL 8 Type E Self-Protected Manual Combination Starter (XTPR) consists of a Manual Motor Protector (XTPR) and a UL Listed Line Side Adapter (e.g. ). The Type E Self-Protected Manual Combination Starter alone is a legitimate short-circuit protective device and disconnect means for the downstream motor, while a contactor can be added to provide remote operation of the motor circuit D D D D XTPRP6C XTPRPC XTPRP0C XTPRP6C XTPR00C XTPRP6C XTPRPC XTPR00C XTPR6PC XTPR0C XTPR0C XTPR06C XTPR00C XTPR0C XTPR0C XTPR06DC XTPR0DC XTPR0DC XTPR00DC Accessories Page -8 Technical Data Page -0 Discount Symbol MC7 CA0800K

8 -6 July 008 -Frame Table -8. XTPT Transformer Protective Circuit reakers Global Ratings Type and Type Coordination For the protection of transformers with a high inrush current. Fixed short-circuit trip of times max. settings of FLA Rated Uninterrupted Current I u (Amps) FLA Adjustment Range / Overload Release I r (Amps) Short Circuit Release I rm (Amps) Maximum Motor Ratings Maximum kw Rating AC- P (kw) -Phase 0 0V 80 V 0V 0V V Maximum hp Rating P (hp) -Phase 00V 0V 80V V Screw Terminals umber Frame For manual motor protective circuit breaker switching capacity, see Page -. XTPT is not UL/CSA approved. XTPTP6C XTPTPC XTPTP0C XTPTP6C XTPT00C XTPTP6C XTPTPC XTPT00C XTPT6PC XTPT0C XTPT0C XTPT06C XTPT00C XTPT0C otes: For the protection of transformers with a high inrush current. Single-phasing sensitivity to IEC/E , VDE 0660 Part. Can be snap-fit to IEC/E 607 top-hat (DI) with 7. or mm height. Service Factor (SF) Setting I r of current scale in dependence of load factor: SF =. -> I r = x I n mot SF = -> I r = 0.9 x I n mot Accessories Page -8 Technical Data Page -0 Discount Symbol MC7 CA0800K

9 July Frame Table -9. XTPM Motor Protective Circuit reakers for Starter Combinations Global Ratings Type and Type Coordination Motor Protective Device without Overload Function Rated Uninterrupted Current I u (Amps) FLA Adjustment Range / Overload Release I r (Amps) Short Circuit Release I rm (Amps) Maximum Motor Ratings Maximum kw Rating AC- P (kw) -Phase 0 0V 80 V 0V 0V V Maximum hp Rating P (hp) -Phase 00V 0V 80V V Screw Terminals umber Frame Select by full load amperes. Maximum Motor Ratings (kw, hp) are for reference only. XTPM is not UL/CSA Approved. XTPMP6 XTPMP XTPMP0 XTPMP6 XTPM00 XTPMP6 XTPMP XTPM00 XTPM6P XTPM0 XTPM0 XTPM06 XTPM00 XTPM0 XTPM0 otes: Can be snap-fit to IEC/E 607 top-hat rail with 7. or mm height An appropriate overload relay must be fitted to protect motors against overload. Combinations of the XTPM and XTCE/XTCR Contactors + XTO Overload Relays can be found in the XT Manual and Combination Motor Controllers section. When using the XTPM as short-circuit protection for motors with heavy starting duty, the rated operational current I e must be derated during engineering with the following factors: Class =.0 Class =.0 Class = 0.8 Class 0 = 0.7 Class = 0.6 Class 0 = 0.8 Class = 0. Class 0 = 0. Accessories Page -8 Technical Data Page -0 Discount Symbol MC7 CA0800K

10 -8 July 008 Accessories Auxiliary Contacts Side-Mount Auxiliary Contacts Can be fitted on the right side of manual motor protectors (XTP, XTPR, XTPM) and manual transformer protectors (XTPT) and can be combined with XTPAXSATR and XTPAXFA trip indicating auxiliary contact. Table -0. Side-Mount Auxiliary Contacts Contact Configuration Contact Sequence Screw Terminals Pkg. Qty. umber Spring Cage Terminals Pkg. Qty. umber O-C XTPAXSA XTPAXSAC L L L XTPAXSA.. O-C XTPAXSA O-C XTPAXSA L L L XTPAXSA Orders must be placed in multiples of package quantity listed. Front-Mount Auxiliary Contacts..... L L L XTPAXSA Can be fitted to manual motor protectors (XTP, XTPR, XTPM) and manual transformer protectors (XTPT). mm (XTPR and XTP) or mm (XTPR D) widths of manual motor protectors remain unchanged. Table -. Front-Mount Auxiliary Contacts Contact Configuration Contact Sequence Screw Terminals Pkg. Qty. umber Spring Cage Terminals O-C L L L Pkg. Qty. umber O-0C XTPAXFA XTPAXFAC L L L XTPAXFA 0O-C XTPAXFAC0.. L L L XTPAXFAC0 Orders must be placed in multiples of package quantity listed.. Discount Symbol MC7 CA0800K

11 July Side-Mount Trip Indicating Auxiliary Contacts Can be fitted on the right side of manual motor protectors. Can be combined with standard auxiliary contacts. Trip indication: A. General Trip indication (overload). Short-circuit trip. Local short-circuit indication by red indicator, manually resettable. Table -. Side-Mount Trip Indicating Auxiliary Contacts Contact Configuration Contact Sequence Pkg. Qty. For Use with umber x O XTP, XTPR, XTPM, XTPT XTPAXSATR0 +.. On/Off.. LLL + > Trip + LLL + > x C XTP, XTPR, XTPM, XTPT XTPAXSATR0 +.. On/Off.. LLL + > Trip + LLL + > Orders must be placed in multiples of package quantity listed. Early-Make Front-Mount Auxiliary Contacts XTPXFAEM0 XTPAXFAEM0 For use with XTP, -Frame XTPR and XTPT. Can be fitted to the front of a manual motor protector. mm width of manual motor protector remains unchanged. For early energization of undervoltage release, e.g. in Emergency-Stop circuits to E 600. Table -. Early-Make Front-Mount Auxiliary Contacts Contact Configuration Contact Sequence Pkg. Qty. For Use with umber O.. XTP XTPXFAEM0 O XTPR, XTPM, XTPT XTPAXFAEM0.. Orders must be placed in multiples of package quantity listed. Discount Symbol MC7 CA0800K

12 -0 July 008 Shunt Release C Current Limiter Contact Sequence Can be used to trip the manual motor protector from a remote location. Can be fitted on the left side of manual motor protectors. Cannot be combined with the XTPAXUVR. DC: Intermittent operation sec. Table -. Shunt Release umber Screw Terminals XTPAXSRVH XTPAXSR8VH XTPAXSRVH XTPAXSR0V60H XTPAXSR08V60H XTPAXSR0VH XTPAXSR0VH XTPAXSR0VH XTPAXSR0V60H XTPAXSR80VH XTPAXSR00VH XTPAXSRVH XTPAXSR0V60H XTPAXSR80V60H XTPAXSRVDC XTPAXSR8VDC XTPAXSR60VDC XTPAXSRVDC XTPAXSRVDC XTPAXSR0VDC XTPAXSRVDC Orders must be placed in multiples of package quantity listed. Undervoltage Release umber Spring Cage Terminals XTPAXSRC0VH XTPAXSRCVDC Pkg. Qty. Can be used to trip the manual motor protector from a remote location. Can be fitted on left side manual motor protectors. Cannot be combined with XTPAXSR. When combined with a circuit breaker, it can be used as Emergency- Stop device to IEC/E 600. Table -. Undervoltage Release umber Screw Terminals XTPAXUVRVH XTPAXUVRV60H XTPAXUVR8VH XTPAXUVR60VH XTPAXUVRVH XTPAXUVR0V60H XTPAXUVR08V60H XTPAXUVR0VH XTPAXUVR0VH XTPAXUVR0VH XTPAXUVR0V60H XTPAXUVR80VH XTPAXUVR00VH XTPAXUVRVH XTPAXUVR0V60H XTPAXUVR80V60H XTPAXUVRV60H umber Spring Cage Terminals XTPAXUVRC0VH Pkg. Qty. Orders must be placed in multiples of package quantity listed. C D U D Contact Sequence The XTPAXCL enhances the switching capacity of the XT manual motor protectors. It can be used with the XTP, XTPR...C, XTPR...DC for individual or group protections. The rated uninterrupted current is 6A for IEC and A for UL/CSA. It can be mounted next to or behind the manual motor protector. See Tables -7 and -76 for ratings when using the current limiter. Table -6. Current Limiter Description Contact Sequence To enhance the switching capacity of non- L XTPAXCL inherently safe A Manual Motor Protectors to ka/ T 0V Max. rated operation voltage Ue = 690V, rated uninterrupted current I u = 6A. Can be used for individual and group protection. For group protection and in combination with the XTPR D, order additional XTPAXIT incoming terminal if required. Mounting next to or behind the manual motor protector. 6 6A XTPR...D: 0 ka/00v, ka/690v. Lockable Rotary Handle Pkg. Qty. umber Table -7. Replacement Lockable Rotary Handle Description Pkg. Qty. umber Lockable Rotary Handle that mounts XTPAXLRH directly to the XTPR manual motor protectors. Comes standard with XTPR. Orders must be placed in multiples of package quantity listed. Discount Symbol MC7 CA0800K

13 July IP6 Rotary Handle Mechanism Table -8. IP6 Rotary Handle Mechanism Description Plug-in connection shafts, XTPAXRHMSFT_ can be cut to desired length for mounting depths of 0 0 mm. Carrier with extension shaft included. With O/OFF switch position and + (tripped), lockable with padlocks, 8 mm hasp. Can be locked in the O position, if required. Rotary Handle Mechanisms ship with door interlock disables. See instruction publication with product for how to enable door interlock. Orders must be placed in multiples of package quantity listed. Pkg. Qty. umber Complete Kits Includes Handle, Shaft, and Required Hardware Rotary Handle Mech IP6 lack For use on main switches to XTPAXRHM IEC/E 600. Rotary Handle Mech IP6 Red/Yellow For use on main switch XTPAXRHMRY with Emergency-Stop function to IEC/E 600. Rotary Handle Mech IP6 lack For use on main switches to XTPAXRHM90 IEC/E 600 where XTPR is mounted 90 from vertical. Rotary Handle Mech IP6 Red/Yellow For use on main switch XTPAXRHM90RY with Emergency-Stop function to IEC/E 600 where XTPR is mounted 90 from vertical. Separate Parts Rotary Handle Only IP6 lack For use on main switches to XTPAXRH IEC/E 600. Rotary Handle Only IP6 Red/Yellow For use on main switch XTPAXRHRY with Emergency-Stop function to IEC/E 600. Rotary Handle Only IP6 lack For use on main switches to XTPAXRH90 IEC/E 600 where XTPR is mounted 90 from vertical. Rotary Handle Only IP6 Red/Yellow For use on main switch XTPAXRH90RY with Emergency-Stop function to IEC/E 600 where XTPR is mounted 90 from vertical. Shaft Only, 7 mm length. XTPAXRHMSFT Shaft Only, 7 mm length, ulk Pack of pcs. XTPAXRHMSFT7 Shaft Only, 98 mm length, ulk Pack of pcs. XTPAXRHMSFT98 Shaft Only, 7 mm length, ulk Pack of pcs. XTPAXRHMSFT7 Telescopic Adapter Sealing Facility Table -9. Telescopic Adapter Description Telescoping Adapter, 7 mm Depth, for use with XTP and -Frame XTPR MMPs Pkg. Qty. umber With mm top-hat rail to IEC/E 607 for compensation of the mounting depth of rear mounted devices in surface mounted enclosures. Stepless adjustment via scale from 7 mm. Table -. Sealing Facility XTPAXTEA Description Pkg. Qty. umber To prevent tampering with the overload XTPAXSW release and the test function. It can be sealed using industry standard sealing wire. For use with XTPR manual motor protectors. Orders must be placed in multiples of package quantity listed. Discount Symbol MC7 CA0800K

14 - July 008 Three-Phase Commoning Links Frame Frame D For parallel power feed to several manual motor protectors on terminals, and. Table -. Three-Phase Commoning Links For Use with Frame MMP with no side mounted auxiliaries or voltage releases Qty. MMP Length of Link (mm) Unit Width (mm) Pkg. Qty. umber 90 XTPAXCLKA XTPAXCLKA 80 XTPAXCLKA XTPAXCLKA Each MMP with one auxiliary contact or trip-indicating auxiliary contact fitted on the right XTPAXCLK + 9 XTPAXCLK XTPAXCLK XTPAXCLK Frame D Each MMP with an auxiliary contact and trip-indicating auxiliary contact mounted on the right or a voltage release mounted on the left. MMP with no side mounted auxiliaries or voltage releases XTPAXCLKC + 8 XTPAXCLKC XTPAXCLKAD 6 XTPAXCLKAD 0 XTPAXCLKAD Each MMP with one auxiliary contact or trip-indicating auxiliary contact fitted on the right XTPAXCLKD XTPAXCLKD XTPAXCLKD Each MMP with an auxiliary contact or trip-indicating auxiliary contact mounted on the right or a voltage release mounted on the left XTPAXCLKCD XTPAXCLKCD Protected against accidental contact. -Frame short circuit proof Ue = 690V, Iu = 6A; D-Frame short circuit proof Ue = 690V, Iu = 8A. Frame links can be combined by rotating mounting. Frame D links cannot be combined. Orders must be placed in multiples of package quantity listed. Discount Symbol MC7 CA0800K

15 July Shroud for Unused Commoning Link Terminals Table -. Shroud for Unused Terminals of Three-Phase Commoning Links For Use Description Pkg. with Qty. umber -Frame XTPR D-Frame XTPR To cover unused terminals on three-phase commoning link. Protected against direct contact. Orders must be placed in multiples of package quantity listed. 0 XTPAXUTS XTPAXUTSD Incoming Terminal for Three-Phase Commoning Link Table -. Incoming Terminal For Use with Pkg. Qty. umber -Frame XTPR, XTP XTPAXIT For three-phase commoning link, protected against accidental contact, Ue = 690V, Iu = 6A; For conductor cross-sections:. mm stranded;. 6 mm flexible with ferrules, AWG -6. Orders must be placed in multiples of package quantity listed. Line-Side Adapter Table -. Line-Side Adapter For Use with -Frame XTPR to create a UL 8 Type E/F Manual Combination Starter Pkg. Qty. umber D-Frame XTPR to create a UL 8 Type E/F Manual Combination Starter D is for three-phase commoning link, finger- and back-of-hand proof, Ue = 690V, Iu = 60A for conductor cross sections:. mm stranded,. 6 mm flexible with ferrule, AWG -6. Orders must be placed in multiples of package quantity listed. D cannot be combined with three-phase commoning links. Discount Symbol MC7 CA0800K

16 - July 008 Combination Connection Kits Table -. Combination Connection Kits on-reversing Starters For Use with Description Std. Pack umber XTPR... + XTCE... Comprised of: XTPAXTPC Mechanical connection element for XTPR... and contactor Main current wiring between XTPR... and contactor in tool-less plug connection Cable guidance Use contactor auxiliary switch XTCEXFAT_. Control cable guidance: max. 6 cables up to. mm external diameter or cables up to. mm external diameter. XTPR... + XTCE...C Comprised of: XTPAXTPCC XTPR...D + XTCE...D DI rail adapter plate Main current wiring between XTPR and contactor XTPAXTPCD Reversing Starters XTPR... + XTCE...0_ XTPR... + XTCE...C Comprised of: Mechanical connection element for XTPR... and contactor Reversing starter main current wiring in tool-less plug connection Control cables for electrical interlocking in toolless plug connection: KM: A KM: KM: KM: A KM: A KM: A Cable guidance Use contactor auxiliary switch XTCEXFAT_. Control cable guidance: max. 6 cables up to. mm external diameter or cables up to. mm external diameter. Comprised of: DI rail adapter plate Reversing starter main current wiring XTPAXTPCR XTPAXTPCRC Star-Delta Starter Sets XTPR... + XTCE... Comprised of: DI rail adapter plate Main current wiring between XTPR... and contactor Electrical interlock between delta and star contactor Use as contactor auxiliary switch XTCEXFAT_ XTPAXSDS XTPR... + XTCE...C Comprised of: DI rail adapter plate Main current wiring between XTPR... and contactor XTPAXSDSC Discount Symbol MC7 CA0800K

17 July Combination Connection Kits Table -. Combination Connection Kits (Continued) For Use Description with Std. Pack umber Electrical Connection Module DI Rail Adapter Plates XTPR... + XTCE...C XTPR...D + XTCE...D XTPAXTPC XTPAXTPCR Comprised of: Main current wiring between XTPR... and contactor Use only in combination with busbar adapter Comprised of: Main current wiring between XTPR...D and contactor Use only in combination with busbar adapter Comprised of: mm wide adapter plate with one DI rail Connection element for side-by-side positioning of further plates XTPAXECMC XTPAXECMD XTPAXTPCP XTPR... + XTCE...C XTPAXECMC Comprised of: mm wide adapter plate with two DI rails Connection element for side-by-side positioning of further plates XTPAXTPCRP XTPAXECMD XTPR...D + XTCE...C XTPR...D + XTCE...D Comprised of: mm wide adapter plate with two DI rails Connection cams for further plates For use with reversing and star-delta starters XTPAXTPCPD Lateral Module Connection Element Can be grouped on the DI rail adapter Expansion of the mounting width by 9 mm Orders must be placed in multiples of package quantity listed. XTPAXLM For connection of several DI rail adapters XTPAXCE Discount Symbol MC7 CA0800K

18 -6 July 008 Pushbutton MMP Enclosures -Frame Table -6. Insulated Enclosures for Surface Mounting of XTP Pushbutton Motor-Protective Circuit reakers Global Usage Degree of For Use Description Approx. Dimensions Protection with umber mm [in] H x W x D IP0 EMA XTP MMP Only or with: XTPAXFA, XTPXFAEM0, XTPAXSA..., XTPAXUVR..., XTPAXSR... XTPXECS0 8 x 80 x 6. [6. x. x.9] IP6 EMA R, X,, With actuation membrane. XTPXECS6 8 x 80 x 6. [6. x. x.9] IP6 EMA R, X,, IP6 EMA R, X,, IP6 EMA R, X,, IP6 EMA R, X,, XTP MMP Only or with: XTPAXFA, XTPAXUVR, XTPAXSR, XTPAXCL XTP MMP Only or with: XTPAXFA, XTPXFAEM0, XTPAXUVR..., XTPAXSR, XTPAXCL Integrated terminal for PE() connection, two M cable entry knockouts at top and at bottom. Lockable in OFF position. XTPXECSLO6 8 x 80 x 9. [6. x. x.] Lockable in OFF position in combination with XTPXFAEM0 Early Make front mount auxiliary contact With Emergency-Stop (E-Stop) pushbutton actuator, Red-Yellow With Emergency-Stop (E-Stop) pushbutton actuator, Red-Yellow key release XTPXECSLE6 8 x 80 x 9. [6. x. x.] XTPXECSES6 8 x 80 x 77. [6. x. x 6.98] XTPXECSEK6 8 x 80 x 77. [6. x. x 6.98] Table -7. Insulated Enclosures for Surface Mounting of XTP Pushbutton orth American Usage Degree of For Use Description Approx. Dimensions Protection with umber mm [in] H x W x D IP EMA XTP MMP Only or with: XTPAXFA, XTPXFAEM0, XTPAXSA..., XTPAXUVR..., XTPAXSR, XTPAXCL XTPXEAS 8 x 80 x 6. [6. x. x.9] IP6 EMA R, X,, With actuating diaphragm XTPXEAS6 8 x 80 x 6. [6. x. x.9] IP6 EMA R, X,, IP6 EMA R, X,, IP6 EMA R, X,, IP6 EMA R, X,, XTP MMP Only or with: XTPAXFA, XTPAXUVR, XTPAXSR, XTPAXCL XTP MMP Only or with: XTPAXFA, XTPXFAEM0, XTPAXUVR..., XTPAXSR, XTPAXCL uilt-in terminal for PE(). orth American enclosures come with conduit adapters for use with /" PT. Lockable in OFF position XTPXEASLO6 8 x 80 x 9. [6. x. x.] Lockable in OFF position in combination with XTPXFAEM0 Early Make front mount auxiliary contact. With Emergency-Stop (E-Stop) pushbutton actuator, Red-Yellow With Emergency-Stop (E-Stop) pushbutton actuator, Red-Yellow key release XTPXEASLE6 8 x 80 x 9. [6. x. x.] XTPXEASES6 8 x 80 x 77. [6. x. x 6.98] XTPXEASEK6 8 x 80 x 77. [6. x. x 6.98] Dimensions Page -8 Discount Symbol MC7 CA0800K

19 July Table -8. Insulated Enclosures for Flush Mounting of XTP Pushbutton Global and orth American Usage Degree of For Use Description Approx. Dimensions Protection with umber mm [in] H x W x D Front IP0 EMA Front IP6 EMA R, X,, XTP Only or with: XTPAXFA, XTPXFAEM0, XTPAXSA, XTPAXUVR, XTPAXSR, XTPAXCL XTPXECF0 9 x 90. x. [.08 x. x.] With actuation membrane XTPXECF 9 x 90. x. [.08 x. x.] Front IP6 EMA R, X,, Front IP6 EMA R, X,, Front IP6 EMA R, X,, Front IP6 EMA R, X,, Integrated terminal for PE() connection. Rotary MMP Enclosures XTP Only or with: XTPAXFA, XTPAXUVR, XTPAXSR, XTPAXCL XTP Only or with: XTPAXFA, XTPXFAEM0, XTPAXUVR, XTPAXSR, XTPAXCL Lockable in OFF position XTPXECFLO 9 x 90. x. [.08 x. x.] Lockable in OFF position in combination with XTPXFAEM0 Early Make front mount auxiliary contact With Emergency-Stop (E-Stop) pushbutton actuator With Emergency-Stop (E-Stop) pushbutton actuator, key release XTPXECFLE 9 x 90. x. [.08 x. x.] XTPXECFES 9 x 90. x 7.9 [.08 x. x 6.9] XTPXECFEK 9 x 90. x 7.9 [.08 x. x 6.9] -Frame D-Frame Table -9. Insulated Enclosures for Surface Mounting of -Frame (0. A) XTPR Rotary Motor-Protective Circuit reakers Global Usage Degree of For Use Description Approx. Dimensions Protection with umber mm [in] H x W x D IP with vertical mounting -Frame XTPR Only or with: XTPAXFA, XTPAXSA, XTPAXSATR, XTPAXUVR, XTPAXSR, XTPAXCL Cover with aperture dimensioned to accommodate front of MMP. IP0, when mounted turned through 90 to left/right XTPAXECS 60 x 0 x [6.0 x.9 x.09] IP6 With black/grey rotary handle XTPAXECS6 60 x 0 x 0 [6.0 x.9 x.] IP6 IP0 -Frame XTPR Only or with: XTPAXSA, XTPAXUVR, XTPAXSR, XTPAXCL With red/yellow rotary handle for use as Emergency-Stop switches to IEC/ E 600 Cover with aperture dimensioned to accommodate front of MMP. XTPAXECS6RY 60 x 0 x 0 [6.0 x.9 x.] XTPAXECS0 8 x 80 x 0 [6. x. x.9] IP IP -Frame XTPR Only or with: XTPAXFA, XTPAXSA, XTPAXUVR, XTPAXSR, XTPAXCL With black/gray rotary handle XTPAXECS 8 x 80 x. [6. x. x.9] With red/yellow rotary handle for use as Emergency-Stop switches to IEC/ E 600 XTPAXECSRY 8 x 80 x. [6. x. x.9] M metric cable entry knock-out, top and bottom. Cable push-through membrane, top and bottom, in the back plate and as a control line entry. Includes and PE terminals. Integrated terminal for PE() connection, two M cable entry knockouts at the top and bottom. Discount Symbol MC7 CA0800K

20 -8 July 008 Table -60. Insulated Enclosures for Surface Mounting of -Frame (0. A) XTPR Rotary orth American Usage Degree of For Use Description Approx. Dimensions Protection with umber mm [in] H x W x D IP EMA,, R -Frame XTPR Only or with: XTPAXSA and XTPAXFA, XTPAXUVR and XTPAXFA, XTPAXSR and XTPAXFA, XTPAXCL uilt-in and PE terminal, lower part without knockouts. With black/gray rotary handle XTPAXEAS 60 x 0 x 0 [6.0 x.9 x.] With red/yellow rotary handle for use as Emergency-Stop switch to VDE 0 XTPAXEASRY 60 x 0 x 0 [6.0 x.9 x.] Table -6. Insulated Enclosures for Surface Mounting of -Frame XTPR (0. A) Rotary Motor-Protective Circuit reakers with XTPAXFAEM0 Early-Make Front Mount Auxiliary Contact Global Usage Degree of Protection IP6 IP6 IP IP For Use with -Frame XTPR and XTPAXFAEM0 only or with: XTPAXFA, XTPAXSA, XTPAXSATR, XTPAXUVR, XTPAXSR, XTPAXCL -Frame XTPR and XTPAXFAEM0 only or with: XTPAXFA, XTPAXUVR, XTPAXSR, XTPAXCL Table -6. Insulated Enclosures for Surface Mounting of -Frame XTPR (0. A) Rotary with XTPAXFAEM0 Early- Make Front Mount Auxiliary Contact orth American Usage Degree of Protection IP EMA,, R For Use with -Frame XTPR Only or with: XTPAXSA, XTPAXUVR, XTPAXCL uilt-in and PE terminal, lower part without knockouts. Description umber Approx. Dimensions mm [in] H x W x D With black/gray rotary handle XTPAXECSEM6 60 x 0 x 0 [6.0 x.9 x.] With red/yellow rotary handle for use as Emergency-Stop switches to IEC/E 600 XTPAXECSEM6RY 60 x 0 x 0 [6.0 x.9 x.] With black/gray rotary handle XTPAXECSEM 8 x 80 x 0 [6. x. x.9] With red/yellow rotary handle for use as Emergency-Stop switches to IEC/E 600 Description XTPAXECSEMRY 8 x 80 x 0 [6. x. x.9] umber Approx. Dimensions mm [in] H x W x D With black/grey rotary handle XTPAXEASEM 60 x 0 x 0 [6.0 x.9 x.] With red/yellow rotary handle for use as Emergency-Stop switch to VDE 0 XTPAXEASEMRY 60 x 0 x 0 [6.0 x.9 x.] Table -6. Insulated Enclosures for Flush Mounting of -Frame (0.-A) XTPR Rotary Global Usage Degree of For Use Description Approx. Dimensions Protection with umber mm [in] H x W x D Front IP0 -Frame XTPR Only or with: XTPAXSA, XTPAXUVR, XTPAXSR, XTPAXCL Cover with aperture dimensioned to accommodate front of MMP. XTPAXECF0 9 x 8 x 96 [.08 x. x.78] Front IP -Frame XTPR Only or with: XTPAXSA, XTPAXUVR, XTPAXSR, XTPAXFA, XTPAXCL Integrated terminal for PE() connection. With black/gray rotary handle XTPAXECF 9 x 8 x [.08 x. x.88] With red/yellow rotary handle for use as Emergency-Stop switches to IEC/E 600 XTPAXECFRY 9 x 8 x [.08 x. x.88] Table -6. Insulated Enclosures for Surface Mounting of D-Frame ( 6A) Rotary Motor-Protective Circuit reakers Degree of For Use Description Protection with umber IP6 EMA,, R IP6 EMA,, R D-Frame XTPR Only or with: XTPAXFA, XTPAXFAEM0, XTPAXSA, XTPAXSATR, XTPAXUVR, XTPAXSR, XTPAXCL Approx. Dimensions mm [in] H x W x D With black/gray rotary handle XTPAXECSD6 0 x 60 x 97 [9. x 6.0 x 7.76] With red/yellow rotary handle for use as Emergency-Stop switches to IEC/E 600 XTPAXECSD6RY 0 x 60 x 97 [9. x 6.0 x 7.76] Integrated terminal for PE() connection. Metric knockouts: Top bottom: M/M In backplate: M/M Control cable entry: M0 Discount Symbol MC7 CA0800K

21 July MMP Enclosure Accessories Table -6. XTPR Manual Motor Protector Enclosure Padlock Attachment For Use Description with XTPAXECS6, XTPAXECS6RY, XTPAXECSEM6, XTPAXECSEM6RY, XTPAXECS, XTPAXECSRY, XTPAXECSEM, XTPAXECSEMRY XTPAXECSD6, XTPAXECSD6RY XTPAXECF, XTPAXECFRY Orders must be placed in multiples of package quantity listed. Lockable in the 0-position of the XTPR manual motor protector. Lockable in the OFF position of the -Frame XTPR manual motor protector. Table -66. eutral Terminal for use with XTP and -Frame XTPR Flush-Mount Enclosures For Use Description with XTPXECF0, XTPXECF, XTPAXECF0, XTPAXECF, XTPAXECFRY Orders must be placed in multiples of package quantity listed. Padlocking feature. Up to padlocks with 6 mm hasp thickness. For use as main switch to IEC/E 600. Pkg. Qty. umber XTPAXPL XTPAXPL XTPAXPL Pkg. Qty. umber For connection of a fifth conductor 0 XTPAXT Metric Cable Glands to E 6 Indicating Lights with eon ulb With locknut and internal strain relief IP68 up to bar, hydrogen free Table -67. Metric Cable Glands Description Pkg. Qty. 0. mm Metric Cable Gland 6 mm Wire. mm Metric Cable Gland 9 7 mm Wire. mm Metric Cable Gland mm Wire. mm Metric Cable Gland 8 mm wire umber 0 XTPAXMCG0 0 XTPAXMCG XTPAXMCG XTPAXMCGG Orders must be placed in multiples of package quantity listed. IP6 Metric Diaphragm Grommet For use with XTPR and XTP enclosures Lights do not carry individual IP or EMA rating. All enclosure ratings remain valid when using indicating lights. Table -69. Indicating Lights Color Description Indicating Light White Green Red 0V 0 0V 0V 0V 0 0V 0V 0V 0 0V 0V Pkg. Qty. umber XTPAXILW XTPAXILW XTPAXILWC XTPAXILG XTPAXILG XTPAXILGC XTPAXILR XTPAXILR XTPAXILRC Orders must be placed in multiples of package quantity listed. IP6 With internal push-through diaphragm Table -68. IP6 Metric Diaphragm Grommet Description Pkg. Qty. umber 0. mm Diaphragm Grommet mm Wire. mm Diaphragm Grommet 8 mm Wire. mm Diaphragm Grommet mm Wire 0 XTPAXMDG0 0 XTPAXMDG 0 XTPAXMDG With integral push-through diaphragm. Orders must be placed in multiples of package quantity listed. Discount Symbol MC7 CA0800K

22 -0 July 008 Technical Data and Specifications Table -70. XT Technical Data and Specifications XTPP6 XTP06 XTPRP6 XTPR0 XTPR06D XTPR06D XTPMP6 XTPM0 General Standards IEC/E 6097, VDE 0660, UL 8, CSA C. o. Climatic proofing Damp heat, constant, to IEC ; damp heat, cyclic, to IEC Ambient temperature, C Storage Open Enclosed Mounting position - / 80 - / - / / 80 - / - / / 70 - / - / 0 - / 80 - / - / 0 XTPTP6 XTPT0 - / 80 - / - / Direction of incoming supply As required As required As required As required As required Degree of protection Device Terminals Protection against direct contact Shock resistance half-sinusoidal shock ms to IEC (g) IP0 IP00 IP0 IP00 IP0 IP00 IP0 IP00 Finger- and back-of-hand proof Altitude (m), maximum Terminal capacity Solid (mm) Flexible with ferrule to DI 68, (mm) Solid or stranded (AWG) x ( 6) x ( 6) x ( 6) x ( 6) 8 x ( 6) x ( 6) x ( 6) x ( 6) 8 x ( ) x ( ) x ( ) x ( ) x ( 6) x ( 6) x ( 6) x ( 6) 8 Terminal screw tightening torque Main cable, m Main cable, lb-in Control circuit cable, m Control circuit cable, lb-in Main contacts Rated impulse withstand voltage (U imp ), V AC Overvoltage category / pollution degree III / III / III / III / III / Rated operational voltage (U e ), V AC Rated uninterrupted current = rated operational current (I u = I e ) in amperes or current setting of the overcurrent release or current setting of the overcurrent release 6 or current setting of the overcurrent release or current setting of the overcurrent release IP0 IP00 x ( 6) x ( 6) x ( 6) x ( 6) 8 Rated frequency, Hz Current heat loss (-pole at operating temperature), W Lifespan, mechanical (ops),000 0,000 0,000 0,000 0,000 Lifespan, electrical (AC- at 00 V) (ops),000 0,000 0,000 0,000 0,000 Maximum operating frequency, operations/hr Short-circuit rating AC See Page -. DC (ka) (up to XTPR06) 0 (XTPR00 XTPR0) Motor switching capacity AC- (up to 690 V) in amperes DC- (up to V) in amperes ( contacts in series) (up to XTPM06) 0 (XTPM00 XTPR0) 6 6 ( contacts in series) or current setting of the overcurrent release 60 (up to XTPT06) 0 (XTPT00 XTPT0) CA0800K

23 July Table -70. XT Technical Data and Specifications (Continued) XTPP6 XTP06 XTPRP6 XTPR0 XTPR06D XTPR06D XTPMP6 XTPM0 XTPTP6 XTPT0 Releases Overload release setting range (x I u ) Fixed short-circuit release (x I u ) 0 Short-circuit release tolerance ± 0% ± 0% ± 0% ± 0% ± 0% Phase-failure sensitivity IEC/E , VDE 0660 Part IEC/E , VDE 0660 Part Temperature compensation to IEC/E 6097, VDE 0660, C Operating range, C Temperature compensation residual error for T > 0 C, %/K - / 0 - / - / 0 - / - / 0 - / - / 0 - / - / 0 - / < 0. < 0. < 0. < 0. < 0. Table -7. Auxiliary Contacts Technical Data and Specifications Description XTPAXSA XTPAXFA XTPA()XFAEM XTPAXSATR Rated Impulse withstand voltage, U imp (V AC) Overvoltage category/pollution degree III/ III/ III/ III/ Rated operational voltage U e (VAC) U e (VDC) 0 Safe isolation to VDE 06 Part and Part /A etween auxiliary contacts and main contacts (V AC) Rated operational current AC- 0 0 V, I e (A) 80 V, I e (A) 0 0 V, I e (A) DC- L/R < 0 ms V, I e (A) 60 V, I e (A) V, I e (A) 0 V, I e (A) Lifespan.. 0. Mechanical, operations (x 6 ) Electrical, operations (x 6 ) Contact reliability (@ U e = V DC, U min 7V, < -8 < fault at x 8 operations I min =. ma, fault probability (λ) Positively driven contacts to ZH /7 Yes Short-circuit rating without welding Fuseless FAZ-/-HI FAZ-/-HI Fuse (A gg/gl) Terminal Capacity Solid or flexible conductor with ferrule (mm ) Solid or stranded (AWG) CA0800K

24 - July 008 Table -7. Undervoltage Release Technical Data and Specifications Description XTPAXUVR Cross-sections Solid or flexible conductor with ferrule (mm ) x (0.7.) x (0.7.) Solid or stranded (AWG) x (8 ) x (8 ) Main Contacts Rated operational voltage, U e (V AC) 80 Rated operational voltage, U e (V DC) Pick-up voltage, x U s 0.8. Drop-out voltage, x U s Power Consumption Pick-up AC (VA) Sealing AC (VA) Table -7. Current Limiter Description XTPAXCL Table -7. Shunt Release Technical Data and Specifications Description XTPAXSR Cross-sections Solid or flexible conductor with ferrule (mm ) x (0.7.) x (0.7.) Solid or stranded (AWG) x (8 ) x (8 ) Main Contacts Rated operational voltage, U e (V AC) 80 Rated operational voltage, U e (V DC) AC Operating Range, x U s 0.7. DC Operating Range, x U s (intermittent operation s) 0.7. Power Consumption Pick-up AC (VA) Sealing AC (VA) Pick-up DC (VA) Sealing DC (VA) Rated Impulse withstand Voltage (Uimp), V AC 0 Overvoltage Category/ Pollution Degree III/ Rated operational voltage, Ue (V AC) 690 Rated interrupted current = Rated operational current 6 (lu = le) in amperes I > I > I > 6 I > I > I > 6 ack-up protection range with XTPAXCL Rated short-circuit breaking capacity range XTPR XTPR V AC cn cc Inherently short-circuit proof cc rms [ka] 0 XTPR... Inherently short-circuit-proof XTPR + XTPAXCL XTPR Figure -97. XTP, XTPR - and -Pole Circuits with DC and AC Current Rated Current n [A] Min. Cross-Section Protected 80-V, Hz, Cu mm Device Type XTPRP6C Figure -98. Protection of PVC Insulated Cables Against Thermal Overload at Short Circuit The table indicates which minimum cable cross-sections are protected by XTPR motor protective circuit breakers up to their rated conditional short circuit current Iq.... XTPR6PC XTPR0C XTPR06C XTPR00C XTPR0C XTPR06DC XTPR0DC XTPR0DC XTPR00DC XTPR0DC XTPR08DC XTPR06DC ack-up protection range with XTPAXCL Rated short-circuit breaking capacity range XTPR D XTPR D V AC cn cc Inherently short-circuit proof cc rms [ka] 0 Figure -99. Fuseless Installation with XTPR, ack-up Protection Diagrams Inherently short-circuit-proof XTPR...D + XTPAXCL Rated Current n [A] XTPR D Rated Current n [A] CA0800K

25 July Time/Current Curve Characteristics The time/current characteristic, the current limiting characteristics and the I t characteristics were determined in accordance with DI VDE 0660 and IEC The tripping characteristic of the inverse-time delayed overload releases (thermal overload releases or a releases) for DC and AC with a frequency of 0 to 00 Hz also apply to the time/current characteristic. The characteristics apply to the cold state. At operating temperature, the tripping times of the thermal releases are reduced to approximately %. Under normal operating conditions, all three poles of the device must be loaded. The three main conducting paths must be connected in series in order to protect single-phase or DC loads. With -pole loading, the maximum deviation in the tripping time for times the setting current and upwards is ±0% and thus in accordance with DI VDE 06. The tripping characteristics for the instantaneous, electromagnetic overcurrent releases (short-circuit releases or n releases) are based on the rated current I n, which is also the maximum value of the setting range for circuit-breakers with adjustable overload releases. If the current is set to a lower value, the tripping current of the n release is increased by a corresponding factor. The characteristics of the electromagnetic overcurrent releases apply to frequencies of /60 Hz. Appropriate correction factors must be used for lower frequencies up to 6-/ Hz, for higher frequencies up to 00 Hz and for DC. Time/current characteristics, current limiting characteristics and I t characteristics are available on request. Milli-seconds Seconds Minutes x Figure -0. MMP Tripping Characteristics XTP, XTPR Frame and XTPT (not for XTPM) Milli-seconds Seconds Minutes h h XTP, XTPR Frame XTPT x Rated Operational Current XTPR Frame D x Rated Operational Current Figure -. MMP Tripping Characteristics XTPR Frame D CA0800K

26 - July 008 I ^ D [ka] XTP XTPR Frame XTPM cc A 0 A 6 A/ A 6. A.0 A. A.6 A A 0. A U e = 00 V 0. A cc rms [ka] 0.6 A 6 8 i dt 6 [A s] st half-wave XTPR Frame XTPM A 0 A 6 A 6. A.0 A. A.6 A U e = 00 V..0 A cc rms [ka] Figure -. MMP Let-Through Tripping Characteristics XTP, XTPR Frame, XTPT, XTPM ID ^ [ka] 0 XTPR Frame D cc i dt [A s] 6 st half-wave XTPR Frame D 6/8 A /0/ A A 6 A 6/8 A /0/ A A 6 A U e = 00 V U e = 00 V 0 cc rms [ka] 0 cc rms [ka] Figure -. MMP Let-Through Tripping Characteristics XTPR Frame D CA0800K

27 July Manual Motor Protector Short Circuit Ratings Rated uninterrupted current I u = Rated operational current I e. Rated conditional short circuit current I q IEC/E Rated ultimate short circuit breaking capacity I cu IEC/E Rated operational short circuit breaking capacity I cs IEC/E Table -7. Manual Motor Protector Short Circuit Ratings Global Use, IEC/E 6097 I u 0V 00V 0V 0V 690V I q I cu I cs Fuse I q I cu I cs Fuse I q I cu I cs Fuse I q I cu I cs Fuse I q I cu I cs Fuse A ka ka ka A ka ka ka A ka ka ka A ka ka ka A ka ka ka A XTP with classification Type and Type XTPR C, XTPT, XTPM with classification Type and Type XTPR DC with classification Type and Type XTPR C, XTPT, XTPM with Current Limiter XTPAXCL XTPR C, XTPT, XTPM with () Current Limiters XTPAXCL o upstream protective device required, as it is the auto-protected range (0/ ka Frame, ka Frame D). = ot required. XTPR C, XTPT, XTPM Required back-up fuse if the short circuit current exceeds the rated conditional short circuit current (I cc > I q ); XTP, XTPR...DC Fuse (A gg/gl) for enhancing the switching capacity of the motor protective circuit breaker to 0 ka CA0800K

28 -6 July 008 Table -76. Ratings for Group Motor Applications UL 8 / CSA C. o. Maximum Protective Device for UL/CSA Group Protection umber Rating is pending UL approval. Contact Eaton for availability. ka V AC IEC/E Rated Uninterrupted Current I u (Amps) FLA Adjustment Range / Overload Release I r (Amps) Short Circuit Release I rm (Amps) XTP Frame, Manual Motor Protector with Thermal and Magnetic Trip XTPP6C XTPPC XTPP0C XTPP6C XTP00C XTPP6C XTPPC XTP00C XTP6PC XTP0C XTP0C XTP06C XTP00C 0 XTP0C Max. RMS Sym Current V (ka) w/current Limiter XTPAXCL Maximum Fuse Rating (A) w/current Limiter XTPAXCL Circuit reaker Max (A) w/current Limiter XTPAXCL 8 8 XTPR Frame (all Screw and Spring Cage terminal options), Manual Motor Protector with Thermal and Magnetic Trip XTPRP6C XTPRPC XTPRP0C XTPRP6C XTPR00C XTPRP6C XTPRPC XTPR00C XTPR6PC XTPR0C XTPR0C XTPR06C XTPR00C XTPR0C XTPR0C XTPR Frame D, Manual Motor Protector with Thermal and Magnetic Trip XTPR06DC XTPR0DC XTPR0DC XTPR00DC XTPR0DC XTPR08DC XTPR06DC XTPT Frame D, Manual Motor Protector with Thermal and Magnetic Trip XTPTP6C XTPTPC XTPTP0C XTPTP6C XTPT00C XTPTP6C XTPTPC XTPT00C XTPT6PC XTPT0C XTPT0C XTPT06C XTPT00C XTPT0C CA0800K

29 July Table -77. UL 8 Type E Ratings Manual Motor Protector Screw Terminals umber Line Side Adapter umber XTPR Frame + XTPRP6 XTPRP6C XTPRPC XTPRP0C XTPRP6C XTPR00C XTPRP6C XTPRPC XTPR00C XTPR6PC XTPR0C XTPR0C XTPR06C XTPR00C XTPR0C XTPR0C XTPR Frame D + D XTPR06DC XTPR0DC XTPR0DC XTPR00DC D D D D FLA Adjustment Range / Overload Release I r (Amps) Short-Circuit Release I rm (Amps) UL8 Type F Application Max. RMS Symmetrical Short-Circuit Ratings (ka) Maximum Upstream Protective Device (A) 0V 80/77V /7V Maximum Fuse V Maximum Circuit reaker V For UL8 Type F applications, the Manual Motor Protector assembly does not require a dedicated upstream protective device in the panel, thus a maximum rating is not required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required ot Required CA0800K

30 -8 July 008 Dimensions 9 [.66] [.77] XTPAXFA_ XTPAXFA_ 9 [.66] XTPAXFA_ [.77] [.77]. [.] [.7] 7 [.9] 8 [.] [.77] [.97] 88 [.6] 9 [.70] XTPAXFA_ Figure -. XTP (Approximate Dimensions in mm [in]) Figure -., Manual Transformer Protectors XTPR, XTPT and XTPM (Approximate Dimensions in mm [in]) [.6] 0 [.] 0 [.7] XTPAXFA_ 6 [.6] [.77] [.9] 0 [.8] [.7] 7. [.0] 8 [.6] 7 [.00] [.7] 7 [6.7] XTPAXFA_ Figure -6. Manual Motor Protector XTPR DC (Approximate Dimensions in mm [in]) [.77] 8 [.] 80 [.] 90 7 [.] [.87] * 9 [.66] 9 [.66] XTPAXFAEM0 [.77] [.7] * IEC/E 607 DI Rail 7. [.0] [.7] 9. [.9] 7. [.0] 70 [.76] [.77] [.97] 68 [.68] 86 [.9] XTPAXFAEM0 Figure -7. Current Limiter XTPAXCL (Approximate Dimensions in mm [in]) Figure -8. MMPs with Early-Make Auxiliary Contacts XTPR C + XTPAXFAEM0 (Approximate Dimensions in mm [in]) CA0800K

31 July [.8] (07 [8.], [6.0], 99 [.90]) 6 [.] 90 [.77] [.] [.] 7 [.06] 9 [.] 6 [.0] 68 [.68] Overlapping Mounting to Extend the Three-Phase Commoning Link Figure -9. Standard Auxiliary Contact XTPAXSA (Approximate Dimensions in mm [in]) Figure -. Three-Phase Commoning Link XTPAXCLK, XTPAXCLK, XTPAXCLK, and XTPAXCLK (Approximate Dimensions in mm [in]) [9.] (8 [.]) 6 [.] 90 [.77] [.] 9 [.] 6 [.0] 68 [.68] 6 [.8] 7 [.06] Figure -. Three-Phase Commoning Link XTPAXCLKC, XTPAXCLKC (Approximate Dimensions in mm [in]) Figure -. Trip Indicating Auxiliary Contact XTPAXSATR (Approximate Dimensions in mm [in]) 7. [.0] 6 [.0] [.] 6 [.] 90 [.77] [.] 7 [.87] 8 [.89] [.6] 8 [.7] 9 [.9] 68 [.68] XTPAXIT Figure -. Undervoltage / Shunt Release XTPAXUVR, XTPAXSR (Approximate Dimensions in mm [in]) Figure -. Incoming Terminal, Line Side Adapter XTPAXIT, (Approximate Dimensions in mm [in]) 80 [7.09] (90 [.]) [.77] 7 [.06] Figure -. Three-Phase Commoning Link XTPAXCLKA, XTPAXCLKA (Approximate Dimensions in mm [in]) CA0800K

32 -0 July [.] 6 [.] 0 [8.07] [.] [.0] XTPAXCLKAD 60 [.] [.] XTPAXCLKCD [.0] 6 [.] 6 [.] [.9] [.] XTPAXCLKAD [.0] [.] [.] XTPAXCLKCD [.0] 6 [.] Figure -8. Three-Phase Commoning Link XTPAXCLKCD and XTPAXCLKCD (Approximate Dimensions in mm [in]) 98 [.86] [.] XTPAXCLKAD [.0] Figure -6. Three-Phase Commoning Link XTPAXCLKAD, XTPAXCLKAD and XTPAXCLKAD (Approximate Dimensions in mm [in]) 6 [.] [9.] [.] XTPAXCLKD [.0] 6 [.] 70 [6.69] [.] XTPAXCLKD [.0] 6 [.] 7 [.6] [.] XTPAXCLKD [.0] Figure -7. Three-Phase Commoning Link XTPAXCLKD, XTPAXCLKD and XTPAXCLKD (Approximate Dimensions in mm [in]) CA0800K

33 July [6.] 8 [6.] 80 [.] 6. [.9] XTPXECS0 XTPXECS6 XTPXEAS XTPXEAS6 80 [.] 6. [.9] 77. [6.98] XTPXECSEK6 XTPXECSES6 XTPXEASEK6 XTPXEASES6 8 [6.] 80 [.] 6. [.9] 9. [.] XTPXECSLE6 XTPXECSLO6 XTPXEASLE6 XTPXEASO06 Figure -9. Insulated Enclosures for Surface Mounting of XTP (Approximate Dimensions in mm [in]) 69 [.7] 69 [.7] 9 [.08] 9 [.08] 90. [.] 9 [.66]. [.] XTPXECF0 XTPXECF 69 [.7] 90. [.] 9 [.66]. [.] 7.9 [6.9] XTPXECFEK XTPXECFES 9 [.08] 90. [.] 9 [.66]. [.] XTPXECFLE XTPXECFLO Figure -0. Insulated Enclosures for Flush Mounting of XTP (Approximate Dimensions in mm [in]) CA0800K

34 - July 008 Drilling Dimensions. [.8] 8 [6.] 70 [.76] 8 [6.] [6.0] 80 [.] 90 [.] 0 [.9] XTPAXECS0 0 [.8] [.7] 98 [.86] SV-PKZ0-CI 80 [.] 97. [.8]. [.9] XTPAXECS XTPAXECSRY 97. [.8] 0 [.8] 8 [.]. [.8] XTPAXECSEM XTPAXECSEMRY 8 [.] Drilling Dimensions. [.8] [.7] 8 [6.] [.0] [6.0] 80 [.] XTPAXECS_ + XTPAXPL XTPAXECSEM_ + XTPAXPL. [.8] 8 [.] 8 60 [7.] [6.0] 0 [.9] XTPAXECSH XTPAXECS 7. [.87] [.09] XTPAXEAS 8 60 [7.] [6.0] 0 [.9] 7. [.87] [.06] 0 [.] Drilling Dimensions M 7 [6.7] M XTPAXECS6 XTPAXECS6RY XTPAXECSEM6 XTPAXECSEM6RY XTPAXEAS XTPAXEASRY XTPAXEASEM XTPAXEASEMRY XTPAXECSH6 XTPAXECSH6RY XTPAXECSEMH6 XTPAXECSEMH6RY 0 [.8] [.7] 98 [.86] SV-PKZ0-CI [.9] 0 [.8] 8 [.] Drilling Dimensions M [.7] 8 60 [7.] [6.0] [.0] 7 [6.7] 97 [.8] XTPAXECS6_ + XTPAXPL XTPAXECSEM6_ + XTPAXPL M Figure -. Insulated Enclosures for Surface Mounting of XTPR... (Approximate Dimensions in mm [in]) CA0800K

35 July [.7] 9 [.08] [.7] [.6] R 6 8 [.7.6] 8 [.] 80 [.] 96 [.78] [.88] XTPAXECF0 XTPAXECF XTPAXECFRY 70 7 [.76.8] Mounting Cutout XTPAXECF... 0 [.8] 98 [.86] 8 [.8] 8 [.] 0 [.8] [.7] 9 [.08] [.8] 80 [.] 96 [.78] [.88] 8 [.] XTPAXECF_ + XTPAXPL Figure -. Insulated Enclosures for Flush Mounting of XTPR... (Approximate Dimensions in mm [in]) CA0800K

36 - July 008 [.] 98 [.86] [.6] SV-PKZ-CI 0 [9.] 7 [.8] 60 [6.0] XTPAXECSD6 XTPAXECSD6RY [.8] 8 [7.] 97 [7.76] XTPAXECSD6_ + XTPAXPL Drilling Dimensions.6 [.] Dia. 7 [.8] 0 [9.] 9 [7.60] 60 [6.0] 86 [7.] 8 [.] 0 [.8] XTPAXECSD6 [.60] Figure -. Insulated Enclosures for Surface Mounting of XTPR...D (Approximate Dimensions in mm [in]) [.69] Dia. 6 [.] 8 [.89] 6 [.] 8 [.89] 9. [.77] 6 [.] At least 0 [.9] up to Cover Hinge Mounting Depth: 0 0 [.9 9.] from the top edge of the mounting rail to the front edge of the panel door/cover Figure -. Rotary Handle Mechanism XTPAXRHM (Approximate Dimensions in mm [in]) CA0800K

37 July 008 Combination Motor Controllers - Contents Description Page Standards and Certifications umber Selection Product Selection Accessories Technical Data and Specifications Dimensions Reference Data XT Combination Motor Controller and Manual Motor Controller Product Description The new Cutler-Hammer XT IEC Open on-reversing and Reversing Manual Motor Controllers from Eaton s electrical business combine a Manual Motor Protector with an IEC Contactor(s) to provide a complete motor protection solution by combining motor disconnect function, thermal overload protection, magnetic short circuit protection and remote control operation in one compact, assembled unit. These assembled Manual Motor Controllers cover motors with FLA ratings from 0.A to 6A. The UL 8 Type F labeled Combination Motor Controller (CMC) includes a Line Side Adapter (LSA). These assembled Combination Motor Controllers cover motors with FLA ratings from 0.A to A. Application Description The XT IEC on-reversing and Reversing Manual and Combination Motor Controllers can be used in the following applications: XTSC and XTSR Manual Motor Controller for Single and Multi Motor Panels The preassembled XT Manual Motor Controllers (MMC) combine a Manual Motor Protector, a Wiring Connector Link and IEC Contactor. MMCs can also be field installed with separate MMP, WCL and Contactor(s). An IEC magnetic contactor has been added to allow for remote operation of the motor circuit. XTFC and XTFR Combination Motor Controller (UL 8, Type F), for Single and Multi Motor Panels The preassembled IEC Combination Motor Controllers combine a Line Side Adapter, Manual Motor Protector, Wiring Connector Link and IEC Contactor. The XTPR are UL listed as UL 8, Type E Self- Protected Manual Combination Starters. This UL listing allows these devices to be used in motor circuits without having to add separate branch short circuit protection. An IEC magnetic contactor has been added to allow for remote operation of the motor circuit. Group Motor Installations Since the (Manual Combination Starters) are UL listed for Group Motor Installations, the IEC Manual Motor Controllers provide a compact, assembled package for Group Motor Installations up to V. For Group Installations (in-panel SCPD) applying the traditional / tap rule, the and Combination Motor Controllers July be used on 80V Delta systems along with 80Y/77V and Y/7V slash rated Wye systems. For Group Installations, applying the more recent / tap conductor rule, a maximum 0V Delta is permitted or 80Y/77V and Y/7V slash rated Wye systems. For actual UL 8 Type E/F applications (out-of-panel upstream feeder Short- Circuit Protective Device [SCPD] only), a maximum 0V Delta is permitted or 80Y/77V and Y/7V slash rated Wye systems. For Manual At Motor Disconnect applications, a maximum 0V Delta is permitted or 80Y/77V and Y/7V slash rated Wye systems. Features O/OFF rotary handle with lockout provision Visible trip indication Test trip function Motor applications from 0.A to 6A Class overload protection uilt-in heater and magnetic trip elements to protect the motor Phase loss sensitivity Type coordination Ambient compensated up to C [0 F] Control inputs located at front of starter for easy access and wiring Wide range of coils DI Rail mount XTSC _ Mounting plates XTSC C_, XTSC D motor controllers Adjustment dial for setting motor FLA Short circuit trip at times the maximum setting of the FLA adjustment dial UL 8 Type F CMC High Fault Short Circuit Ratings: Refer to Table -89. O-C Auxiliary Contact as standard on Manual Motor Controller and Combination Motor Controller CA0800K

38 -6 Combination Motor Controllers July 008 Standards and Certifications UL 8 Type F Combination Motor Controller IEC Type Approved per IEC UL Listed File o. E98 CE Mark Table -78. MMC and CMC Applications XT IEC Manual & Combination Motor Controllers Group Installation Using the in-panel Main SCPD and an MMC without a factory assembled LSA. UL 8 Type F Combination Motor Controller Only Upstream Feeder SCPD required with factory assembled LSA; no dedicated in-panel Main SCPD for CMC. ote: For Type Coordination of MMCs, see Tables -90 through -9 on Pages -6 and -6. Protection in Different Controller Types A UL 8 Type E Self-protected Manual Combination Starter/Motor Controller consists of a single device having integral short circuit protection, a main set of contacts, motor overload protection, and July also include a UL listed Line Side Adapter (See Table -78). This type of controller is a legitimate short circuit protective device and disconnect means for the downstream motor. It does require an upstream feeder short circuit protective device, but does not require a dedicated branch circuit protection or a disconnect means if used with a Line Side Adapter. A UL 8 Type E rating means that the unit clears a fault and does not experience any welding of the power poles. A UL 8 Type E self-protected manual motor controller will remain fully functional should a short circuit within its ratings occur. E.g. XTPR. An XT UL 8 Type F Self-protected Combination Motor Controller consists of a UL Listed Type E Self-protected Manual Combination Starter/Motor Controller, a UL Listed Contactor, and a UL Listed Line Side Adapter (See Table -78). While the UL 8 Type E self-protected manual motor protector of this combination motor controller device is a legitimate short circuit protective device and disconnect means for the downstream motor, the contactor is not self-protected. E.g. XTFC, XTFR. In addition, as a complete assembly or modular components, the device should have Type Coordination certification. Type Coordination means the Starter or the Controller must exhibit little or no damage following a major short circuit fault and should be able to be returned to proper service without replacing any parts. Line Side Adapter (LSA) ot required Manual Motor Controller XTSC / XTSR Line Side Adapter (LSA) Required Factory Assembled Combination Motor Controller XTFC / XTFR SCPD = Short Circuit Protective Device (Circuit reaker, Fuses). MMC = Manual Motor Controller Reference: Technical Paper AP0000E. ote: Line Side Adapters are not required for non-u.s. applications. Most countries outside of the U.S. classify the MMP as a thermal magnetic circuit breaker. CA0800K

39 July 008 Combination Motor Controllers -7 umber Selection Table -79. Combination Motor Controllers umbering System X T S C 0 A Design XT = Type SC = Manual Motor Controller FVR SR = Manual Motor Controller FVR FC = Combination Motor Controller, UL 8 Type F FVR FR = Combination Motor Controller, UL 8 Type F FVR Rated Current of MMP -Frame D-Frame P6 = 0.6A P = 0.A P0 = 0.0A P6 = 0.6A 00 = A P6 =.6A P =.A 00 = A 6P = 6.A 0 = A 0 = A 06 = 6A 00 = 0A 0 = A 0 = A 06 = 6A 0 = A 0 = A 00 = 0A 0 = A 08 = 8A 06 = 6A Frame Size MMP = mm, 0. to A D = mm, 6 to 6A Coil Voltage A = V Hz, 0V 60 Hz = 0V Hz, 0V 60 Hz C = V Hz, 80V 60 Hz D = V Hz, V 60 Hz E = 08V Hz F = 0V Hz G = 90V Hz, 0V 60 Hz H = 0V Hz, 77V 60 Hz L = 80V Hz, 0V 60 Hz = 00V Hz P = 80V 60 Hz R = V /60 Hz T = V /60 Hz U = V Hz W = V Hz, 8V 60 Hz Y = 8V Hz AD = 0V DC D = 0V DC RD = V DC TD = V DC WD = 8V DC Frame Size Contactor = mm, 7 to A C = mm, 8 to A D = mm, 0 to 6A XTSC FVR Frame MMP & Frame Contactor XTSC FVR Frame MMP & Frame C Contactor XTSC FVR Frame D MMP & Frame C Contactor XTSC FVR Frame D MMP & Frame D Contactor XTSR FVR Frame MMP & () Frame Contactors XTSR FVR Frame MMP & () Frame C Contactors XTSR FVR Frame D MMP & () Frame C Contactors XTSR FVR Frame D MMP & () Frame D Contactors CA0800K