EN/US INSTRUCTIONS FOR USE OF UBEFLEX KD CART - ISO 2. Version 2

Transcription

1 EN/US INSTRUCTIONS FOR USE OF UBEFLEX KD CART - ISO 2 Version 2 BELINTRA NV

2 CONTENTS Definitions... 3 General safety regulations... 3 Introduction... 4 Product and options... 5 Guidelines for assembly... 8 Guidelines for use...23 Maintenance and inspection...23 Spare parts...24 Warranty and service...24 Waste processing...24 REVISION HISTORY Version Date Code Remark 2 03/02/ This edition supersedes all previous editions. The specifications in this document may be updated without notice. Reproduction or disclosure of the contents of this document is not permitted without the specific consent of Belintra. 2

3 1. Definitions Danger Indicates an immediate hazardous situation that, if not prevented, will result in serious injury or death. Warning Indicates a possible hazardous situation that, if not prevented, could result in serious injury or death. Caution Indicates a possible hazardous situation that, if not prevented, could result in slight or moderate injury. This can also be used to point to unsafe use. 2. General safety regulations In the interest of your safety and to ensure correct use, it is important that you read these instructions carefully, including any tips and warnings, before using the product. Keep these instructions and ensure that users are properly informed as regards the use and safety of the product. Only use the cart in sound condition in accordance with the described purpose and in the environment for which it was produced in compliance with the instruction manual. Belintra is not responsible for: Damage caused by a failure to follow the instructions or by improper use. Consequences of modifications made to the product by the user. Damage caused by use other than the described purpose and the environment for which the cart was produced. Danger: Only pull out 1 basket at a time. If several baskets are tilted or pulled out at the same time, there is a real danger of the cart toppling over. The sill to be bridged is limited to a maximum height of 2 cm. With higher sills the risk of the cart toppling over and causing material damage and/or physical injury is too great. 3

4 Make sure you are in control of the cart at all times. This is to avoid third parties becoming crushed beneath the cart, for example, if it rolls down an inclined surface / stairs out of control. Warning: The maximum load is 25 kg / 55 lb per per of guides and 150 kg / 330 lb per column. Ensure the cart is loaded correctly. Heavy loads at bottom, light loads at top. This is out of ergonomic considerations, and to be able to guarantee the stability of the cart. Before and while moving the cart, check that no people or objects can become crushed by the cart. Adapt your speed to the circumstances at the time. To retain control over the cart in unexpected situations, it should never be moved at more than normal walking pace (4 to 5 km/h / 2 to 3 mph). Modifying the cart can be dangerous. For example, do not attach any extra weight to the side of the cart. This will affect the cart s stability. Assemble the cart as described in the instructions and make sure bolts are properly tightened (torque: 4Nm - advice). Caution: The UBeFlex KD is not suitable for the tunnel washer. The wheels and plastic parts are not resistant to the temperatures that may be encountered in the washer. White markings will also appear on the aluminium profiles. Before moving the cart, check that the wheel brakes have been disengaged. If not, this will cause premature wear on the wheels. When moving the cart, prevent objects from falling from it that could cause malfunctions and/or injury/damage. Avoid protruding parts during transport. Protect the assembly work surface (with card, film, etc.) in order to prevent damage. Wear gloves to prevent injury. 4

5 3. Introduction This manual describes how to use the UBeFlex KD. Because the cart comes in 2 boxes (and therefore requires assembly), you will be taken step by step through the assembly process. The UBeFlex KD is used in the medical sector (nursing homes, care centres, hospitals, etc.). There, this light and manoeuvrable cart can be used to transport ISO 600 x 400 mm / 16 x 24 inch modules, baskets, baskets and/or wire shelves with sterile and non-sterile material. The UBeFlex KD is made from anodised aluminium and comes with adjustable click guides fitted with U- and L-profiles. This makes it possible to transport different types of basket (including those with a high side). 4. Product and options The UBeFlex KD is available in 3 versions. 1. ISO1 D-type - in which the modules are slid into the cart in the deep (600 mm / 24 inch) direction. This is explained in the manual (UBKD1/HL/EN-US/0001). 2. ISO 2 D-type consisting of 2 D-type columns in which the modules are slid into the cart in the deep (600 mm / 24 inch) direction. 3. ISO1 W-type - in which the modules are slid into the cart in the wide (400 mm / 16 inch) direction. This is explained in the manual (UBKD1/HL/EN-US/0001). UBeFlex KD transport carts Item number Description Number of guides External dimensions ISO 1 - D-type 11 P ISO 2 - D-type 22 P ISO 1 - W-type 11 P ISO 1 - W-type 11 P Vertical handles ISO 2 D-type roof or bottom panel (screws inlcuded) 540 x 690 x 1900 mm 21 1/4 x 27 1/8 x 74 3/4 inch 990 x 690 x 1900 mm 38 15/16 x 27 1/8 x 74 3/4 inch 740 x 490 x 1900 mm 29 1/8 x 19 5/16 x 74 3/4 inch 740 x 490 x 1900 mm 29 1/8 x 19 5/16 x 74 3/4 inch 470 x 65 x 30 mm 18 11/16 x 2 9/16 x 1 3/16 inch 5

6 Dimensions ISO 2 D-type 6

7 Accessories Item number Description External dimensions Vertical handles 470 x 65 x 30 mm 18 11/16 x 2 9/16 x 1 3/16 inch Cover for ISO 1 D-type - 7

8 5. Guidelines for assembly Parts list description Quantity Number Part D-type ( ) 1 Vertical profile 4 2 Vertical profile center 2 3 D-type profile connection 9 4 Tap 12 5 Horizontal profile D-type 4 6 Bearing 4 7 Bumper 4 8 Levina castor 2 9 D-type guide (pair) ,5 x 40 mm M12 x Spring washer type S - M Profile cap Spring washer type S - M PVC sealing profile 6 16 M6 x Levina castor with brake 2 18 M12 washer 4 19 M6 x

9 Tools required 8 4 T20 Allen key Allen key Max. 18mm Torx Screwdriver (Torque: between 4-9 Nm) 9

10 1 Parts Quantity Tools 1 2 (2x) (2x) (2x) Torx DETAIL A A 2x DETAIL B 10

11 2 Parts Quantity Tools 2 2x - 3 3x x Torx DETAIL A A DETAIL B 11

12 3 Parts Quantity 5 4x 5 5 DETAIL A MID 12

13 4 Parts Quantity 4 4x 4 DETAIL B C DETAIL C 13

14 5 Parts Quantity Tools 16 4x Allen key x DETAIL C 14

15 6 DETAIL D DETAIL E 15

16 7 Parts Quantity 4 8x 4 DETAIL I DETAIL J J DETAIL J 16

17 8 Parts Quantity Tools 16 8x Torx x Torx DETAIL F F G DETAIL G 17

18 9 18

19 10 Parts Quantity 13 12x 13 DETAIL H H 19

20 11 Parts Quantity Tools 6 4x - 7 4x - 8 2x x x Allen key x x - 6 A C 7 B Optional 17 Max. 18mm Always fit wheels with brakes on the side of the push handles. 17 always fit 2x wheels with brakes on the same side. 20

21 12 Parts Quantity Tools 19 16x Allen key 4 Optional: this step only applies if no push handles are fitted. 21

22 13 Parts 9 Quantity 22x / paar I 9 DETAIL I Optional 1 Place the guide in the locations. Make sure both pins are in the locations. 2 Push the guide against the post and snap the tab in place. 3 Make sure the tab snaps into place over the edge of the post. 22

23 6. Guidelines for use The UBeFlex KD was developed for internal transport. Always begin loading the cart from the bottom. Make sure that the heaviest loads are at the bottom and lighter ones are at the top for optimum stability and ergonomics. Optimize the load according to the height of the baskets or shelves to be transported with the adjustable click guides. Slide modules, baskets or shelves with a low side into the guides (U-profile). Slide modules, baskets or shelves with a high side on top of the guides (L-profile). Unlock the wheels during transport. Lock the wheels when stationary. Respect the maximum load: 25 kg / 55 lb per pair of guides, 150 kg / 330 lb per column. 7. Maintenance and inspection The cart must be inspected by technical staff at least once a year. Important aspects include: inspect for wear, check tightness of screws and examination of welds. The cart can be cleaned with a damp cloth with non-aggressive detergents. CAUTION Aluminium in a tunnel washer leads to white marks. Never use aggressive solvents such as alcohol, thinners and salt solutions to clean the cart. 23

24 8. Spare parts The available spare parts for this item can be consulted in the service desk database at After registering and logging in, you can consult the necessary documentation. 9. Warranty and service The warranty covers material or manufacturing faults in the products from the date of manufacture. Please keep your proof of purchase. Misuse, improper handling, excessive force and repairs by unqualified persons will void the warranty. Contact Belintra for more information about the warranty terms. 10. Waste processing Dispose of all packaging material separately in an environmentally friendly manner. When taking the product out of service, we recommend that you observe the regulations in force at that time. Dispose of this product through an accredited waste processing company or your local waste disposal authority. 24

25 Notes 25

26 Notes 26

27 Notes 27

28 SAFE SMART H E A LT H C A R E S O L U T I O N S