Technical manual. Bure. Walker and Stand-aid with Power Rise Function Bure Rise & Go

Transcription

1 Technical manual Bure Walker and Stand-aid with Power Rise Function Bure Rise & Go

2

3 Replacement parts list L Arm rest, left L/R Support for arm rest, left, right Lock lever Arm rest plate, centre section Support for arm rest, centre Clamp, aluminium R Arm rest, right Telescopic internal tube incl. slide bearing Strap holder, green Handle, foam Vertical frame Plastic bushing, upper Control box 220 V Control box 110 V Actuator Hook (for knee support) Lower frame Bushing, PA Knob, hook adjustment, L= Knob, knee plate adjustment, L= Plastic bushing, lower L/R Hinged arm/knee support, left, right Adjuster plate, knee support Knee support Castor with brake, 125 mm Battery tray Battery Stirrup bar Plastic bushing, stirrup Aluminium cover, stirrup Accessories Part no. Description Handbrake kit, 2 handles Handbrake kit, 1 handle Footplate, aluminium, short Footplate, aluminium, long Chromium drip rod Drip rod holder Oxygen holder Side support Drip rod complete with holder S/M/L/XL Harness (S=95-150cm, M= cm, L= cm, XL= cm) S/M/L/XL Gait training harness (S=95-150cm, M= cm, L= cm, XL= cm) Castor with brake, 75 mm Castor with brake, 100 mm Castor with brake, 125 mm Battery Hand control, up/down (-1, -2, -3) Charge cable, EUR (-UK,-US,-AUS) (-1, -2, -3) Spiral cable, EUR (-UK,-US,-AUS) Heel strap 3

4 Electrical system Technical data Actuator Manufacturer Voltage Lifting power Traction Interlock on lift Amperage T-motion 24V 2000N 2000N 1000N 4.6 A Colour Black Stroke 400 mm Min installation dimensions 605 mm retracted length Protection class IP66 IEC issue 3 Control box + battery Manufacturer Voltage Capacity Protection class Colour Electrical safety T-Motion 24V 2,0 Ah IP66 Black Category II (double insulation) IEC issue 3 4

5 Control box wiring Remove the control box cover to make the connections described below. Use a screw-driver or similar; refer to the special labels on the control box. NOTE! Make sure that plugs are connected to the correct sockets otherwise the actuators can be damaged. 1. Socket for the raise/lower actuator. 2. Remote control socket. 3. Battery terminal socket. 4. Plug socket (NOTE! Plugs must ALWAYS be connected to the control box for IP classification to be valid. Battery charging Connect plug to 230V wall socket. Charging begins automatically and the battery LED flashes green. Make sure the battery is fully charged before using for the first time. It takes around 25 h to fully charge the battery. LEDs on control box and battery Control box green light when power is available from battery/mains socket. Battery: The LED flashes green during charging. The LED shows a constant green light when the battery is fully charged. When the battery is in normal state/in operation, the LED flashes green at regular intervals of 0.5 s ON, 4 s OFF. When the battery requires charging (remaining charge <25%) the LED flashes orange/red at regular intervals of 0.5 s ON, 4 s OFF.. NOTE! The battery always uses a small amount of power in standby mode. The battery has therefore a built-in function that automatically switches it off when remaining charge is < 20%. This situation can particularly happen when product has not been used for a longer period (> one month) - LED is then extinguished. The battery must now be fully charged before used again. 5

6 Maintenance (recommended at least once per year) Check that General The walker feels firm/free from play. The walker does not rattle during manoeuvres. The walker is level and all of its castors are in contact with the floor. The walker is not dirty. Arm rests Arm rests are intact and clean. Arm rest widening is functional. Handle Grips are not damaged/dirty. Handle adjustment is functional. Battery Check that the charging cable is connected to the control box. Check that the remote control is connected to the control box. Check that connections are made according to the wiring diagram. Check that the battery, actuators and control box are not loose. Height adjustment Raising and lowering are functional. The walker feels stable at maximum settings. There is no play between the vertical frame and bottom frame. Height adjustment clamps lock. The electric actuator fitting must be free from play. Height adjustment via remote control is functional. The electric actuator must run smoothly at a constant speed. Frame parts There is no mechanical damage. There are no scratches. End plugs/lower frame fitted. Castors/brakes Castors roll easily. Tread not damaged. The castors are tightly fastened to the lower frame. Castor brakes functional on all castors. Handbrake functional. Harness Belts, seams and Velcro fasteners are whole/ intact. The walker lock tabs (green) are intact. Action Clean with lukewarm soap solution (no petroleum products). Clean; replace if damaged. Replace lock knob. Clean with lukewarm soap solution (no petroleum products). Replace handle grips. Fit lock knobs/plates as required. Fit new cable; this must always be connected to the control box (IP65 classification). Connect or fit new remote control as required. Refer to the wiring diagram in the Technical manual. Tighten; replace with new fasteners as required. Fit new guide sleeves (in frame) or end plugs (in chrome tubes) as required. Tighten all lock bolts. Replace clamps. Tighten the attachment fitting concerned; replace bolts/ lock nuts as necessary. Check that the battery/remote control/actuator are connected in accordance with the wiring diagram. Charge the battery. Contact customer services. If damage is present, contact GATE s customer services. Touch up as necessary. Fit new end plugs. Clean or replace castors (NOTE! Castors are always fixed to the lower frame with thread locker or lock nuts. The castors are sealed and we do not recommend their dismantling; instead, replace the whole castor assembly. Tighten the castor bolt and fit locking nut or use thread locker (depends on model). Replace castor assembly. Adjust the brake or fit new castors. Replace harness. Available in four sizes (S, M, L, XL). Change lock tab. 6

7 General safety/maintenance advice The Bure Walker may only be used: as a WALKING AID / STAND-UP AID. INDOORS on HARD, LEVEL surfaces. Before use, always check that: the product feels firm, secure and stable harnesses, belts and attachments are intact and undamaged Wipe the walker and its armrests clean as necessary; use soap solution/surface disinfectant. Be aware of battery charge status (LED) charge as necessary. ID label Bure Rise & Go 5 1. Part number 2. Product name 3. Date of manufacture 4. Max user weight 5. Serial number 6. EAN code Warranty We provide two years warranty for manufacturing faults (does not apply to wear parts). For further information or enquiries please contact: Gate Rehab Development AB Industrigatan 2, SE Reftele, Sweden Tel: +46 (0) info@gaterd.com 7

8 Technical specifications cm cm 77 cm Dimensions apply to walkers with 125 mm castors. Part No. Product Width Max user weight 89 cm Length Height Weight Armrest/ internal dimension cm 150 kg 89 cm cm 25 kg cm CE marked according to MDD 93/42/EEC SE Patent No. SE Patent pending in other countries Would you like to know more? Contact us at: Tel: Gate Rehab Development AB Industrigatan 2 SE Reftele info@gaterd.se , 4 YOUR HEALTHCARE PARTNER 8