Axial piston pumps type PVPC variable displacement, by a full line of mechanical controls
|
|
- Herbert Tucker
- 5 years ago
- Views:
Transcription
1 Table A60/E Axial piston pumps type PVP variable displacement, by a full line of mechanical controls PVPL4046 PVP are variable displacement axial piston pumps for high pressure operation, with low noise level, suitable for hydraulic oils or synthetic fluids having symilar lubricating characteristics. The actual displacement is dependent on the lenght of stroke of the pumping pistons. This lenght of stroke is determined by the position of the swashing plate that is achieved by two servo pistons with differential areas, against a spring. The rotating barrel forces the pistons in a circular path in and out of the barrel and fluid displacement takes place. Typical section on side shows version L with manual pressure compensator and flow regulation. The available hydraulic controls are shown in sections. The wide range of electrohydraulic proportional controls is shown in tab. A70. SAE J744 mounting flange and shaft (see note ). Max displacement: cm 3 /rev. Max pressure: 280 bar working 350 bar peak. MODEL ODE PVP X2E / 3044 / D X 24D 0 /* Variable displacement axial piston pump Eventual suffix for double pumps X2E = with a fixed displacement pump type PFE (see tab. A005) Type of control (see section ): = manual pressure compensator H = manual pressure compensator, with venting R = remote pressure compensator L = load sensing (pressure & flow) LW= constant power (combined pressure & flow) For electrohydraulic proportional controls, see table A70 Size: 3 = for displacement = for displacement = for displacement 073 and 090 Max displacement of axial piston pump: 029 = 29 cm 3 /rev 046 = 46 cm 3 /rev 073 = 73 cm 3 /rev 090 = 88 cm 3 /rev Type of PFE (for double pumps), see tab. A005 ) pumps with ISO 309/2 mounting flange and shaft (option /M) are available on request 2 OPERATG HARATERISTIS Series number Supply voltage, see section (only for H version) X = without connector (only for H version) See section for available connectors, to be ordered separately Direction of rotation (viewed at the shaft end) D = clockwise S = counterclockwise Shaft (SAE Standard) (): = keyed (7/8 for 029 for 046 /4 for 073 and 090) 5 = splined (3 teeth for for for 073 and 090) Seals material: omit for NBR (mineral oil & water glycol) PE = FPM See notes in section Pump model PVP*3029 PVP*4046 PVP*5073 PVP*5090 External load position Displacement [cm 3 /rev] Theoretical max flow at 450 rpm [l/min] 42 66,7 05,8 27,6 Max working pressure / Peak pressure[bar] 280/ / / /35 Min/Max inlet pressure [bar abs.] 0,8 / 25 0,8 / 25 0,8 / 25 0,8 / 25 Max pressure on drain port [bar abs.],5,5,5,5 Power consumption at 450 rpm and at [kw] 9,9 3,6 50, 54, maximum pressure and displacement Type Type 5 Type Type 5 Type Type 5 Type Type 5 Max torque on the first shaft [Nm] Max permissible load Fax [N] on drive shaft Frad Speed rating [rpm] Fax = axial load Frad = radial load Notes: For speeds over 800 rpm the inlet port must be under oil level with adequate pipes. Maximum pressure for all models with water glycol fluid is 60 bar, with option /PE is 90 bar. Max speed with options /PE and for water glycol fluid is 2000/900/600/500 rpm respectively for the four sizes. A60
2 3 MA HARATERISTIS OF VARIABLE DISPLAEMENT AXIAL PISTON PUMP TYPE PVP Installation position Ambient temperature Fluid Recommended viscosity Any position. The drain port must be on the top of the pump. Drain line must be separated and unrestricted to the reservoir and extended below the oil level as far from the inlet as possible. Suggested maximum line lenght is 3 m. from 20 to +70 Hydraulic oil as per D ; for other fluids see section 5 00 mm 2 /sec at 40 (ISO VG 5 00). Maximum startup viscosity: 000 mm 2 /sec Fluid contamination class ISO 440 class 2/9/6 NAS 638 class 0 (filters at 25 µm value with ß25 75 recommended) Fluid temperature (water glycol) (seals /PE) 3. oils characteristics (for version H) Insulation class H onnector protection degree IP 65 Relative duty factor 00% Supply voltage and frequency See electric feature Supply voltage tolerance ± 0% 4 ELETRI ONNETORS AORDG TO D FOR VERSION H The connectors must be ordered separately ode of connector SP666 SP667 Function onnector IP65, suitable for direct connection to electric supply source As SP666 connector IP65 but with builtin signal led, suitable for direct connection to electric supply source 5 ELETRI FEATURES FOR VERSION H External supply nominal voltage ±0% Power consumption Nominal courrent oil characteristics DIRET URRENT 2 D 24 D 9,2 W,6 A 0,80 A Insulation lass: H ALTERNATE URRENT 24/50A 0/50 A 220/50 A 9 W 0,89 A 0,9 A 0,09 A Protection degree: IP65 Average values based ambient/coil temperature of STALLATION POSITION VERTIAL STALLATION D A B B B B The pump is supplyed whit drain open, and D plugged. Before installation fill the pump with hydraulic oil for at least 3/4 of its volume, keeping it in horizontal position. With exception of pump mounted below the oil level, we recomend to interpose a baffle plate between inlet and drain line. SIDE THE TANK Minimum oil level equal or above the pump mounting surface. A 200mm SIDE THE TANK Minimum oil level below the pump mounting surface. Minimum inlet pressure = 0,8 bar absolute B 800mm, = 200mm OUTSIDE THE TANK, above oil level Minimum inlet pressure = 0,8 bar absolute B 800mm, = 200mm HORIZONTAL STALLATION A SIDE THE TANK SIDE THE TANK OUTSIDE THE TANK, above oil level OUTSIDE THE TANK, below oil level Minimum oil level equal or above the pump mounting surface. A 200mm Minimum oil level below the pump mounting surface. Minimum inlet pressure = 0,8 bar (absolute) B 800mm, = 200mm Minimum inlet pressure = 0,8 bar (absolute) B 800mm, = 200mm = 200mm : inlet line D: drain line A: minimum distance between inlet and drain line B+: permissible suction height : inlet line immersion dept
3 7 DIAGRAMS at 450 rpm (based on mineral oil ISO VG 46 at 50 ) 7. Noise level curves Ambient noise levels measured in compliance with ISO 442 oleohydraulics Test procedure to define the ambient noise level Pumps Shaft speed: 450 rpm. = Qmax = Qmin PVP*3029 PVP*4046 PVP*5073 and PVP* Operating limits = Volumetric efficiency 4 = Power consumption with full flow 2 = Overall efficiency 5 = Power consumption at pressure compensation 3 = Flow versus pressure curve PVP*3029 PVP*4046 PVP*5073 Flow [l/min] Efficiency [%] Power consumption [kw] Flow [l/min] Efficiency [%] Power consumption [kw] Flow [l/min] Efficiency [%] Power consumption [kw] Noise level [db] Noise level [db] Noise level [db] Response times PVP* Response times and pressure peack due to variation 0% 00% 0% of the pump displacement, obtained with an istantaneously opening and shutoff of the delivery line. Pump type T (ms) T2 (ms) PVP* PVP* PVP* Swashing plate angle αmax αmin Flow [l/min] Efficiency [%] Power consumption [kw] PVP* Time [ms] Variation of inlet pressure and reduction of displacement with increasing speed rating Speed rating [rpm/rpmmax] Inlet pressure [rbar abs.] Displacement rating [cm 3 /cm 3 max] A60
4 8 HYDRAULI AND ELETROHYDRAULI ONTROLS Hysteresis and pressure increasing; max 4 bar Manual pressure compensator The pump displacement decreases when the line pressure approaches the setting pressure of the compensator. The pump supplies only the fluid required by the system. Pressure may be steplessly adjusted at the pilot valve. ompensator setting range: bar (35 bar for 090) ompensator standard setting: 280 bar (250 bar for 090) Flow [l/min] H Manual pressure compensator with venting As plus venting function, when a long unloading time is required and heat generation and noise have to be kept at lowest level. ompensator setting range: bar (35 bar for 090) ompensator standard setting: 280 bar (250 bar for 090) Flow [l/min] Hysteresis and pressure increasing; max 4 bar R Remote pressure compensator As, but with remote setting of the compensator by means of a pressure relief valve on the piloting line X. This version can be obtained from version L using a blind plug UNI 5923 M4x2 in pos.l and a restrictor M4 drilled ø 0,75 mm in pos.. ompensator setting range: bar (35 bar for 090) ompensator standard setting: 280 bar (250 bar for 090) Flow [l/min] Hysteresis and pressure increasing; max 4 bar not supplied L Load sensing The pump displacement is automatically adjusted to maintain a constant (load indipendent) pressure drop across an external throttle. hanging the throttle regulation, the pump flow is consequently adjusted. Load sensing control always incorporates an hydraulic compensator to limit the maximum pressure. ompensator setting range: bar (35 bar for 090) ompensator standard setting: 280 bar (250 bar for 090) Differential pressure setting range: 0 40 bar Differential pressure standard setting: 4 bar Flow [l/min] Hysteresis and pressure increasing; max 4 bar not supplied LW onstant power In order to achieve a constant drive torque with varying operating pressure. The swashing angle and therefore the outlet flow is varied so that the product of flow and pressure remains constant. For the best regulation, minimum working pressure is 80 bar. While selecting LW control, the required value of power must be communicated with the order (ex. 0 kw at 450 rpm). Flow [% of max] Minimum power curve 300 Maximum power curve Theoretical power curve
5 9 DIMENSIONS OF PVP*3029: BASI VERSION ONTROL PORTS DIMENSION = Flange SAE 3000 /4 OUT = Flange SAE /4 D, = /2 BSPP = Regulation screw for max displacement,5 cm 3 /rev per turn. Adjustable range 50% to 00% of max displacement. In case of double pump the regulation screw is not always available, please contact our technical office. LET PORT OUTLET PORT OUT DRA PORT DRA PORT Mass: 8 kg SHAFT TYPE SHAFT TYPE 5 SAE B SPLED 3 TEETH 6/32 PITH 30 VOLUTE SPLE TERMEDIATE FLANGE SAE A FOR PFE3 TERMEDIATE FLANGE SAE B FOR PFE4 SAE A SPLED 9 TEETH 6/32 PITH 00 Nm MAX SAE B SPLED 3 TEETH 6/32 PITH 35 Nm MAX OR2325 OR3400 Drawing shows pumps with clockwise rotation (option D): pumps with counterclockwise rotation (option S) will have inlet and outlet ports inverted A60
6 0 DIMENSIONS OF PVP*4046: BASI VERSION ONTROL PORTS DIMENSION = Flange SAE 3000 /2 OUT = Flange SAE 6000 D, = /2 BSPP = Regulation screw for max displacement 2,2 cm 3 /rev per turn. Adjustable range 50% to 00% of max displacement. In case of double pump the regulation screw is not always available, please contact our technical office. LET PORT OUTLET PORT OUT DRA PORT DRA PORT Mass: 24 kg SHAFT TYPE SHAFT TYPE 5 SAE BB SPLED 5 TEETH 6/32 PITH 30 VOLUTE SPLE TERMEDIATE FLANGE SAE A FOR PFE3 TERMEDIATE FLANGE SAE B FOR PFE4 SAE A SPLED 9 TEETH 6/32 PITH 35 Nm MAX SAE B SPLED 3 TEETH 6/32 PITH 250 Nm MAX OR2325 OR3400 Drawing shows pumps with clockwise rotation (option D): pumps with counterclockwise rotation (option S) will have inlet and outlet ports inverted
7 DIMENSIONS OF PVP*5073 and PVP*5090: BASI VERSION ONTROL LET PORT OUTLET PORT OUT DRA PORT PORTS DIMENSION = Flange SAE OUT = Flange SAE 6000 /4 D, = 3/4 BSPP = Regulation screw for max displacement 3,2 cm 3 /rev per turn. Adjustable range 50% to 00% of max displacement. In case of double pump the regulation screw is not always available, please contact our technical office. DRA PORT Mass: 33 kg SHAFT TYPE SHAFT TYPE 5 SAE SPLED 4 TEETH 2/24 PITH 30 VOLUTE SPLE TERMEDIATE FLANGE SAE A FOR PFE3 SAE A SPLED 9 TEETH 6/32 PITH 35 Nm MAX TERMEDIATE FLANGE SAE B FOR PFE4 SAE B SPLED 3 TEETH 6/32 PITH 330 Nm MAX OR2325 OR3400 TERMEDIATE FLANGE SAE FOR PFE5 SAE SPLED 4 TEETH 2/24 PITH 440 Nm MAX OR3400 Drawing show pumps with clockwise rotation (option D): pumps with counterclockwise rotation (option S) will have inlet and outlet ports inverted A60
8 2 DIMENSIONS OF PVP: OTHER ONTROLS VERSION H VERSIONS L, R E VERSION LW TIGHTENG TORQUE = 5 Nm max = Regulation screw for max displacement. Adjustable range 50% to 00% of max displacement). In case of double pump the regulation screw is not always available, please contact our technical office. Drawing shows pumps with clockwise rotation (option D): pumps with counterclockwise rotation (option S) will have inlet and outlet ports inverted and also the consequently position of the control groups Pump type PVP*3029 PVP*4046 PVP*5073 PVP*5090 Version A B D E Mass (kg) H L R LW H L R LW H L R LW , , ,9 34,2 35 /2
Axial piston pumps type PVPC variable displacement, by a full line of mechanical controls
www.atos.com Table A60/E Axial piston pumps type PVP variable displacement, by a full line of mechanical controls PVPH4046 PVP are variable displacement axial piston pumps for high pressure operation,
More informationAxial piston pumps type PVPC with ISO mounting flange variable displacement, hydraulic control
www.atos.com Table TA623/E Axial piston pumps type PVP with ISO mounting flange variable displacement, hydraulic control PVPH4046 PVP are variable displacement axial piston pumps for high pressure operation,
More informationAxial piston pumps type PVPC variable displacement, by a full line of mechanical controls
www.atos.com Table A600/E Axial piston pumps type PVPC variable displacement, by a full line of mechanical controls PVPCCH4046 PVPC are variable displacement axial piston pumps for high pressure operation,
More informationPump model PVPP-*-3023 PVPP-*-3033 PVPP-*-4048 PVPP-*-5060 PVPP-* Max flow at 1500 rpm and 7 bar [l/min]
900 Table A0obs/E Axial piston pumps type PVPP, variable displacement, high pressure operation Hydraulic and electrohydraulic control obsolete components - availability on request PVPP-SLER-08/D PVPP are
More informationVariable displacement axial piston pumps,
ariable displacement axial piston pumps, for open circuit DISPLACEMENTS From To 2.75 in 3 /rev (45 cm 3 /rev) 5.12 in 3 /rev (84 cm 3 /rev) MAX SPEED 3000 min -1 PRESSURE Max. continuous Max. intermittent
More informationHydraulics. Axial Piston Pumps Series PVP. Introduction. With thru shaft option for multiple pump options Swash plate type for open circuit
Introduction *not included Pump with standard compensator, code: "omit" With thru shaft option for multiple pump options Swash plate type for open circuit Pump with load sensing, code: "A" Mounting style
More information2.4 HEAVY DUTY SERIES
2 2.4 HEAVY DUTY SERIES CONTENTS PPV102 Ordering Code 2.4.1 Heavy Duty Series 2.4.2 Heavy Duty Series compensator 2.4.3 Standard gear pump models Technical Information 2.4.4 Specifications 2.4.5 Hydraulic
More informationVariable displacement axial piston pumps,
LVP 04 T E Variable displacement axial piston pumps, Edition: 04/04.2000 Replaces: 04/10.99 DISPLACEMENTS From To PRESSURE Max. continuous Max. intermittent Max. peak 29 cm 3 /rev 73 cm 3 /rev 280 bar
More informationVariable displacement axial piston pumps,
Variable displacement axial piston pumps, Edition: 04/04.2000 Replaces: 04/10.99 DISPLACEMENTS From To PRESSURE Max. continuous Max. intermittent Max. peak 29 cm 3 /rev 73 cm 3 /rev 280 bar 315 bar 350
More informationPUMP SIZE Flow rate at 1500 rpm lt/min Operating pressures bar
/7 ED VPPL VARIABLE DISPLACEMENT AXIAL-PISTON PUMPS FOR INTERMEDIATE PRESSURE SERIES OPERATING PRINCIPLE The VPPL are variable displacement axial-piston pumps with variable swash plate, suitable for applications
More informationVariable displacement axial piston pumps,
Variable displacement axial piston pumps, Edition: 04/04.2000 Replaces: 04/10.99 DISPLACEMENTS From To PRESSURE Max. continuous Max. intermittent Max. peak 29 cm 3 /rev 73 cm 3 /rev 280 bar 315 bar 350
More information2.3 MEDIUM HEAVY DUTY SERIES
2 2.3 MEDIUM HEAVY DUTY SERIES CONTENTS PPV11 Ordering Code 2.3.1 Medium Heavy Duty Series 2.3.2 Torque limiter settings Technical Information 2.3.3 Specifications 2.3.4 Hydraulic fluids 2.3.5 Viscosity
More informationPVE /117 ED VARIABLE DISPLACEMENT VANE PUMPS WITH DIRECT PRESSURE ADJUSTMENT SERIES 30 OPERATING PRINCIPLE TECHNICAL SPECIFICATIONS
14 110/117 ED PVE VARIABLE DISPLACEMENT VANE PUMPS WITH DIRECT PRESSURE ADJUSTMENT OPERATING PRINCIPLE The PVE pumps are variable displacement vane pumps with direct pressure regulator. The pump group
More informationRV1P /118 ED VARIABLE DISPLACEMENT VANE PUMPS SERIES 10 OPERATING PRINCIPLE TECHNICAL SPECIFICATIONS HYDRAULIC SYMBOL
14 201/118 ED RV1P VARIABLE DISPLACEMENT VANE PUMPS OPERATING PRINCIPLE TECHNICAL SPECIFICATIONS (measured with mineral oil with viscosity of 46 cst at 40 C) RV1P are variable displacement vane pumps with
More informationSeries PVP Variable Volume Piston Pumps
Series PVP Variable Volume Piston Pumps Catalog HY28-2661-CD/US zp2 hpm12-1.p65, lw, jk 1 Notes Series PVP hpm12-1.p65, lw, jk 2 Introduction Series PVP Series Sizes 6-14 Phased Out For Reference Only
More informationIGP /117 ED INTERNAL GEAR PUMPS SERIES 10 OPERATING PRINCIPLE TECHNICAL SPECIFICATIONS HYDRAULIC SYMBOL
00/7 ED IGP INTERNAL GEAR PUMPS OPERATING PRINCIPLE IGP pumps are volumetric displacement pumps with internal gears, available in five sizes, each divided into a range of different displacement. The pumps
More informationCatalog HY /NA. Catalog HY /NA. Parker Hannifin Corporation Hydraulic Pump Division Marysville, Ohio USA
Catalog HY28-6/NA PV, PVT Series Piston Pumps Variable Volume Catalog HY28-6/NA 1 Catalog HY28-6/NA Notes Series PV 2 Catalog HY28-6/NA Introduction Series PV Quick Reference Data Chart Pump Delivery Approx.
More informationVariable displacement axial piston pump type V30D
Variable displacement axial piston pump type V30D for open circuit Pressure p max Displacement V max = 420 bar (6000 psi) = 260 cm 3 /rev (16.16 cu in/rev) 1.2 1. General description The axial piston variable
More informationVPPM /110 ED VARIABLE DISPLACEMENT AXIAL-PISTON PUMPS OPERATING PRINCIPLE TECHNICAL SPECIFICATIONS HYDRAULIC SYMBOL
16 100/110 ED VPPM VARIABLE DISPLACEMENT AXIAL-PISTON PUMPS OPERATING PRINCIPLE The VPPM pumps are variable displacement axial-piston pumps with variable swash plate, suitable for applications with open
More informationRA / Internal Gear Pump Model GP3, Series 3X Fixed Displacement. Typical application:
Sizes 20 to 32 Internal Gear Pump Model GP3, Series 3X Fixed Displacement up to 5076 PSI 1.25 to 1.98 in 3 (350 bar) (20.6 to 32.5 cm 3 ) RA 10 234/07.97 Characteristics: Peak pressure of up to 5.076 PSI
More information5.2 MEDIUM HEAVY DUTY SERIES SIZE 3
.2 MEDIUM HEAVY DUTY SERIES SIZE 3 CONTENTS PGI101 Ordering Code.2.1 Medium Heavy Duty Series Technical Information.2.2 Specifications.2.3 Hydraulic fluids.2.4 Viscosity range.2. Temperature range.2.6
More informationTPV Variable Displacement Closed Loop System Axial Piston Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 852 / 0815 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Certified Company ISO 9001-14001 ISO 9001 Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415
More informationVariable Displacement Pump A4VG for closed circuits
RE 92 003/05.99 RE 92 003/05.99 replaces: 02.98 Variable Displacement Pump A4VG for closed circuits Sizes 28...250 Series 3 Nominal pressure 400 bar Peak pressure 450 bar A4VG...EP Index Features 1 Ordering
More informationOutput flow In l/min at 1500 min
Introduction With thru drive For single and multiple pumps Swash plate type for open circuit 1. New type of swash plate and large servo piston with strong bias spring achieves fast response, reduce the
More informationAxial Piston Pump Series PV Design 45 Variable Displacement. Catalogue HY /UK February 2007
Design 45 Variable Displacement February 2007 Introduction With thru drive for single and multiple pumps Swash plate type for open circuit Technical Features Low noise level Fast response (eg. PV046: upstroke
More informationP2060 P2075 P2105 P2145 P3105 P3145
Technical Information Technical Features P2 Series Compact design Low noise level Service friendly Reliable Long-lasting Flexible Easy to install High self-priming speed Technical Data P3 Series P2 Series
More informationRE 91808/ AA4VSE Plug-in dual displacement motor. High pressure range. Series 10 Axial piston swashplate design, SAE model
AA4VSE Plug-in dual displacement motor Series Axial piston swashplate design, SAE model RE 91808/09.90 RE 91808/09.90 Brueninghaus Hydromatik Size 250 Nominal pressure 350 bar Peak pressure 400 bar High
More informationTPV Variable Displacement Closed Loop System Axial Piston Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 851 / 0813 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES THE PRODUCTION LINE OF HANSA-TMP Variable Displacement Closed Loop System CONTENTS General Information... Order Code... Manual Control
More informationTPV Variable Displacement Closed Loop System Axial Piston Pump HY-TRANS THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 501 / 1009 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES HY-TRANS THE PRODUCTION LINE OF HANSA-TMP Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415
More informationVARIABLE DISPLACEMENT AXIAL PISTON PUMPS
VARIABLE DISPLACEMENT AXIAL PISTON PUMPS FEATURES Variable displacement axial piston pumps swash plate design ideally suited for medium and high pressure open circuit applications. The compact design allows
More informationPVD /117 ED VARIABLE DISPLACEMENT VANE PUMPS WITH DIRECT PRESSURE ADJUSTER OPERATING PRINCIPLE
14 100/117 ED PVD VARIABLE DISPLACEMENT VANE PUMPS WITH DIRECT PRESSURE ADJUSTER OPERATING PRINCIPLE The PVD pumps are variable displacement vane pumps with mechanical pressure compensator. The pressure
More informationVariable Displacement Open Loop Circuit Axial Piston Pumps AR Series
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Via M.L. King, 6-41122 MODENA (ITALY) Tel: +39 59 415 711 Fax: +39 59 415 729 / 59 415 73 INTERNET: http://www.hansatmp.it E-MAIL:
More informationAXIAL PISTON PUMPS SHPV SECTIONAL VIEW
AXIAL PISTON PUMPS SHPV SECTIONAL VIEW 2 SYSTEM CIRCUIT PUMP AND MOTOR CIRCUIT working loop (high pressure) working loop (low pressure) control fluid suction line case drain fluid Above figure shows schematically
More informationTHE PRODUCTION LINE OF PONAR WADOWICE
PONAR Wadowice S.A. ul. Wojska Polskiego 29 34-100 Wadowice Tel.: +48 33 488 21 00 Fax: +48 33 488 21 03 E-mail: ponar@ponar-wadowice.pl Web: www.ponar-wadowice.pl THE PRODUCTION LINE OF PONAR WADOWICE
More informationV Series AXIAL PISTON PUMP ORDER CODE
V Series AXIAL PISTON PUMP ORDER CODE V A 1 R B S - A D X A 1 Customers demand Pump Series V Links Type (only V -18): none - Standard A - SAE A bolts Ma. (cm 3 /n):, 18, 3,, 38, 4,, 7 Pump Control Type
More informationRA / Internal Gear Pump Model GP2, Series 2X Fixed Displacement. Typical application:
Sizes 6.3 to 16 Internal Gear Pump Model GP2, Series 2X Fixed Displacement up to 576 PSI.397 to.98 in 3 (35 bar) (6.5 to 16 cm 3 ) RA 1 23/6.97 RA 1 23/6.97 Characteristics: Peak pressure of up to 576
More informationMobile Hydraulic Pumps T6G, T67G, T6ZC. Denison Vane Technology, fixed displacement
Mobile Hydraulic Pumps T6G, T67G, T6ZC Denison Vane Technology, fixed displacement aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing
More informationTPV Variable Displacement Axial Piston Pumps CONTENTS. General Information. Installation Instructions. Technical Specifications 6-7
CONTENTS General Information Installation Instructions Technical Specifications Single Pump Installation Drawing Tandem Pump Installation Drawing Mounting Flanges and Shaft Details Rear Pump Mounting Flanges
More informationIPVP High-pressure Internal Gear Pumps for Variable Speed Drives
IPVP High-pressure Internal Gear Pumps for Variable Speed Drives Design and Function 7 6 5 9 2 5 6 7 8 2 9 4a 4b 3 Pinion shaft 2 Internal gear 3 Filler pin 4a Filler segment carrier 4b Filler sealing
More information3.3 VARIABLE DISPLACEMENT MECHANICAL COMPENSATION
. VRIBL ISPLMNT MHNIL OMPNSTION ONTNTS PVV101 Ordering ode..1 Mechanical compensation Technical Information..2 Specifications.. Hydraulic fluids..4 Viscosity range..5 Temperature range..6 Seals..7 Filtration..8
More informationAxial Piston Variable Double Pump A8VO
Axial Piston Variable Double Pump A8VO RE 93010/03.09 1/40 Replaces: 11.07 Data sheet Series 61 / 63 Sizes 55...200 Nominal pressure 350 bar Peak pressure 400 bar for open circuit Contents Ordering Code
More information5.1 MEDIUM HEAVY DUTY SERIES SIZE 2
.1 MEDIUM HEAVY DUTY SERIES SIZE 2 CONTENTS PGI100 Ordering Code.1.1 Medium Heavy Duty Series Technical Information.1.2 Specifications.1.3 Hydraulic fluids.1.4 Viscosity range.1. Temperature range.1.6
More informationSeries 20 Axial Piston Pumps. Technical Information
Series 20 Axial Piston Pumps Technical Information General Description INTRODUCTION Sauer-Danfoss a world leader in hydraulic power systems has developed a family of axial piston pumps. DESCRIPTION Sauer-Danfoss
More informationAXIAL PISTON PUMPS AND MOTORS
HPV-HMF SERIES SECTIONA VIEW AXIA PISTON VARIABE DISPACEMENT PUMP AXIA PISTON FIXED DISPACEMENT MOTOR Purge relief valve High pressure relief valves (adjustable) Cylinder block assembly Shaft seal Output
More informationAXIAL PISTON MOTORS SHMF
SECTIONAL VIEW Purge relief valve High pressure relief valves (adjustable) Cylinder block assembly Shaft seal Output shaft Valve block Shuttle valve Swashplate 2 SYSTEM CIRCUIT PUMP AND MOTOR CIRCUIT working
More informationSeries 20 Axial Piston Pumps. Technical Information
Series 20 Axial Piston Pumps Technical Information General Description INTRODUCTION Sauer-Danfoss a world leader in hydraulic power systems has developed a family of axial piston pumps. DESCRIPTION Sauer-Danfoss
More informationV Series AXIAL PISTON PUMP ORDER CODE
V Series AXIAL PISTON PUMP ORDER CODE V 15 A 1 R B S - A 1 D X A 11 Customers demand Pump Series V Links Type (only V 15-18): none - Standard A - SAE A 2 bolts Ma. Displacement (cm 3 /n): 15, 18, 23, 25,
More informationUŽSISAKYKITE internetu telefonu el. paštu
Features Axial piston pump MA10VO in swashplate design is used in open loop circuits. Flow is proportional to drive speed and displacement. By adjusting the position of the swashplate it is possible to
More informationVINCKE HYDRAULIC PUMPS
: VNK BA10VS 21 Variable displacement axial piston pump of swashplate design for hydraulic open circuit systems. Flow is proportional to drive speed and displacement. It can be infinitely varied by adjustment
More informationVickers. Piston Motors. Inline Piston Motors. Fixed and Variable Displacement. Revised 5/99 691
Vickers Piston Motors Inline Piston Motors Fixed and Variable Displacement Revised 5/99 691 Table of Contents Introduction........................................................................................
More informationPLP Pump (up to 16 cm 3 /r max. 120 bar) PHV Pump (up to 32 cm 3 /r max. 250 bar) PVS Pump (up to 100 cm 3 /r max. 100 bar)
General Catalogue MODEL PLP Pump (up to 16 cm 3 /r max. 120 bar) PHV Pump (up to 32 cm 3 /r max. 250 bar) PVS Pump (up to 100 cm 3 /r max. 100 bar) PSP Pump (up to 100 cm 3 /r max. 160 bar) PSPK Pump (up
More informationHYDRAULICS VINCKE HYDRAULIC PUMPS
VINCKE HYDRAULIC PUMPS TECH-VHP200.1 index 3 link to your page / link a su página Gear pumps Introduction 3 Group 0 3 Group 1 3 Group 2 3 Group 3 4 6 7 12 18 Variable displacement pumps 21 Hand pumps 3
More informationVariable Displacement Pumps
variable displacement pumps variable displacement pumps Variable Displacement Pump Prices Seal Kits Prices Application & Features A10VSO Pumps Dimensions Technical Information Sec:2 Sec:2 Sec:3 Sec:4 Sec:8
More informationIPVP High-pressure Internal Gear Pumps for Variable Speed Drives Technical Data Sheet
IPVP High-pressure Internal Gear Pumps for Variable Speed Drives Technical Data Sheet Design and Function 7 6 5 9 2 8 2 9 4a 4b 3 Pinion shaft 2 Internal gear 3 Filler pin 4a Filler segment carrier 4b
More informationVariable Displacement Open Loop Circuit Axial Piston Pumps. V Series
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 59 415 711 Fax: +39 59 415 729 / 59 415 73 INTERNET: http://www.hansatmp.it E-MAIL:
More informationTPV 1200 BTB. Variable Displacement Closed Loop System Axial Piston Compact Tandem Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 160 / 0516 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Certified Company ISO 9001-14001 ISO 9001 Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415
More informationPilot Operated Pressure Relief Valve Series R5V (Denison)
Characteristics Pilot operated pressure relief valves series R5V have a similar design to the subplate mounted R4V series. The SAE flanges allow to mount the valves directly on the outlet flanges of pumps
More informationAxial Piston Fixed Motor A2FM
Axial Piston Fixed Motor A2FM RE 91001/06.2012 1/46 Replaces: 09.07 Data sheet Series 6 Size Nominal pressure/maximum pressure 5 315/350 bar 10 to 200 400/450 bar 250 to 1000 350/400 bar Open and closed
More informationISO Certificate N 12-E TIC. ISO 9001 Certificate N 12-Q TIC
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Certified Company ISO 9001-14001 ISO 9001 Certificate N 12-Q-0200545-TIC ISO 14001 Certificate N 12-E-0200545-TIC Via M. L. King,
More informationTPV 4000 (EX 28-41) Variable Displacement Closed Loop System Axial Piston Pump HY-TRANS THE TRANSMISSION LINE OF HANSA-TMP HT 16 / M / 280 / 1008 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Via M.L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415 730 INTERNET: http://www.hansatmp.it E-MAIL:
More informationTPV Variable Displacement Closed Loop System Axial Piston Pump MANUFACTURING THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 403 / 1110 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415 730 INTERNET: http://www.hansatmp.it E-MAIL:
More informationGear Pumps / Motors. Series PGP / PGM Fixed Displacement Pumps, Cast-Iron and Aluminium Designs
Gear Pumps / Motors Series PGP / PGM Fixed Displacement Pumps, Cast-Iron and Aluminium Designs Table of contents Heavy-duty Pumps and Motors Series PGP, PGM Contents Page Series 500 Aluminium Table of
More informationAxial piston variable pump (A)A4VSO
Axial piston variable pump (A)A4VSO RA 92050-A/06.09 1/64 Replaces: 09.97 Data sheet Series 10, 11 and 30 Size 40...1000 Nominal pressure 5100 psi (350 bar) Peak pressure 5800 psi (400 bar) Open circuit
More informationAxial Piston Variable Pump AA4VG
Electric Drives and Controls Hydraulics Linear Motion and Assembly Technologies Pneumatics Service Axial Piston Variable Pump AA4VG RA 92003-A/06.09 1/64 Replaces: 03.09 Data sheet Series 32 Size 28...
More informationGenuine Metaris MA10VO/VSO Technical Catalog. Variable Displacement Piston Pump - A10V Series 31 & 52
Genuine Metaris MA10VO/VSO Technical Catalog www.metaris.com Contents General Series MA10VO/VSO Series 31 4 Page Features 4 Technical Data 5 Performance Information 6 Model Code Breakdown 9 Fluid Info
More informationVariable Axial Piston Pump A10V Series - 52/53
Variable Axial Piston Pump A10V eries - 52/53 eries 52/53 - Open Circuit Peak Pressure 315 bar (4,600 psi) Nominal Pressure 250 bar (3,600 psi) izes 10cm 3 /rev - 63cm 3 /rev (0.64in 3 /rev-3.8in 3 /rev)
More information1.3 HIGH PRESSURE SERIES
1.3 HIGH PRESSURE SERIES content Ordering Code 1.3.1 High Pressure Series Technical Information 1.3.2 Specifications 1.3.3 Hydraulic Fluids 1.3.4 Viscosity Range 1.3.5 Temperature Range 1.3.6 Seals 1.3.7
More information4.2 FIXED DISPLACEMENT DOUBLE PUMP
4.2 FIXED DISPLACEMENT DOUBLE PUMP CONTENTS PVF101 Ordering Code 4.2.1 Fixed Displacement Technical Information 4.2.2 Specifications 4.2.3 Hydraulic fluids 4.2.4 Viscosity range 4.2.5 Temperature range
More informationIPVS High-pressure Internal Gear Pumps Technical Data Sheet
IPVS High-pressure Internal Gear Pumps Technical Data Sheet Functional Drawing 5 9 2 8 2 9 4a 4b 3 Pinion shaft 2 Internal gear 3 Filler pin 4a Filler segment carrier 4b Filler sealing segment 5 Axial
More informationTPV 1200 BTB. Variable Displacement Closed Loop System Axial Piston Compact Tandem Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 154 / 0413 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Certified ISO 9001 and 14001 Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415 730 TERNET:
More informationAxial piston variable pump A4VG Series 32. Europe. RE-E Edition: Replaces:
Axial piston variable pump A4VG Series 32 Europe RE-E 92003 Edition: 04.2016 Replaces: 06.2012 High-pressure pump for applications in a closed circuit Size 28 to 125 Nominal pressure 400 bar Maximum pressure
More informationAxial piston variable displacement pump type V60N, Serie 03
Axial piston variable displacement pump type V60N, Serie 03 mainly for mobile applications, commercial trucks etc. Open circuit Nominal pressure Maximum pressure p max Geometric displacement V max = 350
More informationAXIAL PISTON PUMPS SHPV SECTIONAL VIEW
AXIAL PISTON PUMPS SHPV SECTIONAL VIEW 2 AXIAL PISTON PUMPS SHPV SYSTEM CIRCUIT PUMP AND MOTOR CIRCUIT working loop (high pressure) working loop (low pressure) control fluid suction line case drain fluid
More informationExternal Gear Pumps Series F
External Gear Pumps Series F RA 10089/08.11 Replaces: RA 10097 1/60 AZPF-... Fixed pumps Size 4.0...28 cm 3 /rev (.25-1.71 in 3 /rev) Overview of contents Contents Page General 2 Product overview 3 single
More informationProportional Pressure Relief Valve Series RE*T
Characteristics The pressure relief valve series RE*T have a proportional solenoid operated pilot stage with integrated electronics and a cartridge main stage. Features Pilot-operated pressure relief valve
More informationAxial piston variable pump A10VSO Series 31
Axial piston variable pump A10VO eries 31 RE 92711 Edition: 10.2016 Replaces: 01.2012 All-purpose medium pressure pump izes 18 to 140 Nominal pressure 280 bar Maximum pressure 350 bar Open circuit Features
More informationAxial Piston Variable Pump A4VG
Electric Drives and Controls Hydraulics Linear Motion and Assembly Technologies Pneumatics Service Axial Piston Variable Pump A4VG RE 92003/03.09 1/64 Replaces: 09.07 Data sheet Series 32 Sizes 28...250
More informationVariable Displacement Plug-In Motor A6VE
Electric Drives and Controls Hydraulics Linear Motion and Assembly echnologies Pneumatics Service Variable Displacement Plug-In Motor A6VE RE 91 606/06.05 1/16 Replaces: 05.99 echnical data sheet Series
More informationAxial Piston Fixed Displacement Pump KFA
Industrial Hydraulics Electric Drives and Controls Linear Motion and Assembly Technologies Pneumatics Service Automation Mobile Hydraulics Axial Piston Fixed Displacement Pump KFA RE 91 501/06.03 1/12
More informationFixed Displacement Pump A4FO Series 10 Axial Piston Unit, Swashplate Design
Fixed Displacement Pump A4FO Series 10 Axial Piston Unit, Swashplate Design Sizes 71 0 Nominal pressure 3 bar Peak pressure 400 bar RE 91455/01.94 RE 91455/01.94 Replaces 07.88 Other fixed displacement
More information» Feeding mechanism of robots and manipulators» Metal working machines» Textile machines» Machines for agriculture» Food industries
HYDRAULIC HW APPLICATION» Conveyors» Feeding mechanism of robots and manipulators» Metal working machines» Textile machines» Machines for agriculture» Food industries» Grass cutting machinery etc. CONTENTS
More informationFIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BQ
FIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BQ BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps.
More informationFIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BQ
FIXED DISPLACEMENT HYDRAULIC VANE PUMPS SERIE BQ BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps.
More informationExternal Gear Pumps Series F
External Gear Pumps Series F AZPF-... Fixed pumps V = 4.0...28 cm 3 /rev Overview of contents ontents Page General 2 Product overview 3 single pumps 4 multiple pumps 5 rive shaft 6 Front cover 7 Line ports
More informationExternal Gear Pumps Series F
External Gear Pumps Series F RE 10 089/02.07 Replaces: Series F Issue 04.04 AZPF-... Fixed pumps V = 4.0...28 cm 3 /rev Overview of contents ontents Page General 2 Product overview 3 single pumps 4 multiple
More informationAP212HP Cast Iron Gear Pumps
Cast Iron Gear Pumps Standard and Low Noise series Reference: 200-P-991236-EN-01 Issue: 09.2016 1/56 Contents Page 1 General information... 5 1.1 External gear pumps components... 6 1.2 Technical data...
More informationPM50 VARIABLE DISPLACEMENT PUMP CLOSED LOOP CIRCUIT T E C H N I C A L C A T A L O G
PM50 VARIABLE DISPLACEMENT PUMP CLOSED LOOP CIRCUIT T E C H N I C A L C A T A L O G PM50 - Variable displacement pump POCLAIN HYDRAULICS OVERVIEW PM50 is a variable displacement, axial piston pump, with
More informationSolenoid directional valves type DPHI and DPHE two stage, ISO 4401 size 10, 16, 25 and 32
www.atos.com Table E0857/E Solenoid directional valves type DPHI and DPHE two stage, ISO 4401 size 10, 16, 25 and 32 DPHE471*/H Spool type, two stage directional valves with solenoids certified according
More informationVariable displacement axial piston pumps
Variable displacement axial piston pumps SVP series GENERAL INFORMATIONS Variable displacement axial piston pump swash plate design for open circuit-flow sharing control valve. The pump has been designed
More informationAxial piston variable pump A10V(S)O Series 31
Axial piston variable pump A10V()O eries 31 RE 92701 Edition: 06.2016 Replaces: 01.2012 ize 18 (A10VO) izes 28 to 1 (A10VO) Nominal pressure 280 bar Maximum pressure 350 bar Open circuit Features Variable
More informationPVX-11 VANE PUMPS. See pages 12 thru 14 for PVX-11 dimensions. VARIABLE DISPLACEMENT, PRESSURE COMPENSATED PERFORMANCE SPECIFICATIONS
PVX-11 VANE PUMPS VARIABLE DISPLACEMENT, COMPENSATED NOTE: See pages thru 14 for PVX-11 dimensions. PERFORMANCE SPECIFICATIONS Displacement (Nominal) 1.5 in 3 /rev. (25 cm 3 /rev.) Displacement (Actual)
More informationPMV0 VARIABLE DISPLACEMENT PUMP CLOSED LOOP CIRCUIT T E C H N I C A L C A T A L O G
PMV0 VARIABLE DISPLACEMENT PUMP CLOSED LOOP CIRCUIT T E C H N I C A L C A T A L O G PMV0 - Variable displacement pump POCLAIN HYDRAULICS OVERVIEW PMV0 is a variable displacement, axial piston pump, with
More informationA Series Variable Displacement Piston Pumps
A Series Variable Displacement Piston Pumps A37 A56 A1637 A16 A10 A Series Variable Displacement Piston Pumps Pump Type Graphic Symbol Geometric Displacement cm 3 /rev 1 5 10 0 50 100 00 300 Maximum Operating
More informationAxial Piston Variable Pump A2VK
Axial Piston Variable Pump A2VK RE 94001/06.10 1/12 Replaces: 07.04 Data sheet Size 12 to 107 Series 1 and 4 Nominal pressure 250 bar Maximum pressure 315 bar Version for pumping plastic components Contents
More informationSeries TMM Axial Piston Motor. Technical Information
Series TMM Axial Piston Motor Technical Information General Description GENERAL DESCRIPTION These motors are designed primarily to be combined with other products in closed circuit systems to transfer
More informationRadial piston motor for compact drives MCR-C
Radial piston motor for compact drives MCR-C RE 15197 Edition: 12.2013 Frame size MCR20 Displacement 1750 cc to 3000 cc Differential pressure up to 450 bar Torque output up to 19099 Nm Speed up to 125
More informationPilot Operated Directional Control Valves Series D1VP, D3DP, D4P, D9P, D11P
Characteristics Series D1VP, D3DP, D4P, D9P, D11P The D1VP is a hydraulically controlled 4/3 or 4/ way directional control valve. The valve can be operated either by the pilot ports X and Y via the subplate
More informationRexroth Hydraulics. Fixed displacement vane pumps Types PVV and PVQ RE /11.97
RE 1 335/1.97 RE 1 335/11.97 Fixed displacement vane pumps Types and Nominal sizes 18 to 193 Series 1X Maximum operating pressure 21 bar Maximum displacement 18 to 193 cm 3 H/A/D 5769/97 Single pump type
More informationAxial piston variable displacement pump type V60N
Axial piston variable displacement pump type V60N For commercial veicles Open circuit Nominal pressure Maximum pressure p max Geometric displacement V max = 350 bar (5075 psi) = 400 bar (5800 psi) = 90
More informationGP PUMP SIZE GP1 GP2 GP3 Displacement range cm 3 /rev clockwise, anticlockwise or reversible (seen from the shaft side)
11 1/117 ED GP EXTERNA GEAR PUPS OPERATING PRINCIPE The GP pumps are fixed displacement external gear pumps with axial clearance compensation. They give high volumetric efficiency even with high operating
More information