Thermal Expansion Absorber For Potable Water TX SERIES TANKS
|
|
|
- Joel Harrison
- 5 years ago
- Views:
Transcription
1 Thermal Expansion Absorber For Potable Water TX SERIES TANKS PRODUCT DATA SPECIFICATIONS Maximum Pressure: 150 psi (1034 kpa). Maximum Temperature: 200 F (93 C). Standard Factory Air Charge: 40 psi (276 kpa). NOTE: Relief valve must be set to 150 psi (1034 kpa) maximum. Materials: Diaphragm: Butyl Rubber. Liner: Polypropylene. Connection: Brass. Approvals: SBCCI, NSF61, City of Los Angeles and others. IAPMO listed. GENERAL The Honeywell Thermal Expansion Absorber is a pre-pressurized Expansion tank with a butyl diaphragm designed to control excess pressure in potable hot water systems. It s use for household as well as small commercial hot water heaters will save energy and operating problems by preventing relief valve operation due to excessive system pressure. INSTALLATION Connect the Honeywell Thermal Expansion Absorber tank to the cold water inlet line to the water heater. The Honeywell tank connection must be between the water heater and any valve or backflow preventer. Adjust the Honeywell tank air pressure to the minimum cold water pressure by adding or releasing air from the tank. Fill tank and piping with cold water, open hot water faucet to allow a small trickle of water. Turn on water heater and allow it to reach normal operating temperature. Close hot water faucet. Contents General...1 Specifications...1 Installation...1 Ordering Information...2 Thermal Expansion Commercial & ASME Tanks...3 Product Information
2 QUICK SIZING CHART SUPPLY PRESSURE (PSIG) SYMBOLS AM SERIES CHECK VALVE MIXING VALVE C M H TO DISHWASHER IF PERMITTED BY CODES HEAT TRAP 8 MAX WATER HEATER ALLOWABLE SERVICE VALVE LOCATION EXPANSION TANK COLD WATER SUPPLY V = Any device which turns the domestic water system into a closed system such as: backflow preventers, check valves or pressure reducing valves. 6 M23700 WATER HEATER U.S. GALLONS TX 5 TX 12 TX 25 M23701 Based on: Heating water from 70 to 140 F (21 to 60 C). Maximum pressure maintained at least 10% below relief valve setting of 150 psi (1034 kpa). Factory pre-charge of 40 psi (276 kpa) - no need to change when selected according to this chart. V is optional depending on local codes. If a V type valve is used, it is mandatory that a thermal expansion tank be installed as shown. Otherwise dangerously high pressures could result or water heater safety relief valve will frequently expel water. If no V device is used, the thermal expansion tank is not required. Product Number Total Volume in gal. (L) Max. Acceptable volume in gal. (L) Dia. in inches (mm) Length in inches (mm) NPT System Conn. TX (7.6).09 (3.4) 8 (203) 12-5/8 (321) 3/4 in. male TX (16.7) 3.2 (12.1) 11 (279) 15 (381) 3/4 in. male TX-25V 10.3 (39) 10.3 (39) 15 3/8 (391) 19 1/4 (489) 1 in. female ORDERING INFORMATION When purchasing replacement and modernization products from your TRADELINE wholesaler or distributor, refer to the TRADELINE Catalog or price sheets for complete ordering number. If you have additional questions, need further information, or would like to comment on our products or services, please write or phone: 1. Your local Honeywell Automation and Control Products Sales Office (check white pages of your phone directory). 2. Honeywell Customer Care 1885 Douglas Drive North Minneapolis, Minnesota In Canada Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive, Toronto, Ontario M1V 4Z9. International Sales and Service Offices in all principal cities of the world. Manufacturing in Australia, Canada, Finland, France, Germany, Japan, Mexico, Netherlands, Spain, Taiwan, United Kingdom, U.S.A
3 THERMAL EXPANSION COMMERCIAL & ASME TANKS Sizing Procedure The procedure for sizing Thermal Expansion Tanks depends on four (4) vital pieces of information. 1. ASME or non-asme requirement. 2. Calculated thermally expanded water volume. 3. Minimum water pressure experienced at the tank location. 4. Maximum water pressure allowable at the tank location. The tank required for any application can be sized by the following equation: TV = Design Pressure Factor x expanded water, where TV is the total tank volume required in gallons. Sizing Example A 240 gallon (908.5 L) water heater with a 150 F (65.5 C) aquasat setting is installed with a 125 psi (862 kpa) maximum pressure requirement. For a static supply line pressure of 60 psi (414 kpa), what tank model is required for critical protection? Table 1. Expansion Factor (Water). Operating Temperature of Water Heater in F ( C) 100 (38) (49) (54) (60) (66) (71) (77) (82) Expansion Factor Based on initial temperature of 40 F (4 C). For glycol solution expansion factors contact factory. EXAMPLE 1. Total Water Heater Volume in gallons Water Expansion Factor (see Table 1) Calculate Expanded Water in gallons (Line 1 x Line 2 = 240 x ) Design Pressure Factor (see Table 2) Tank Volume Required in gallons (Line 3 x Line 4 = 4.3 x 2.1) Select Tank Model. TX-25V or TX30V-C Line pressure in psi (kpa) Table 2. Design Pressure Factor (DPF). Maximum Pressure in psi (kpa) 100 (689) 125 (862) 150 (1034) 40 (276) (345) (414) (483) (552) For conditions not shown in table, use equation: DPF = Maximum Allowable Pressure Maximum Allowable Pressure Line Pressure
4 PRODUCT INFORMATION Table 3. Non-ASME Construction Product Number Tank Volume in gal. (L) Maximum Acceptable Volume in gal. (L) Connection Size NPT Diameter in inches (mm) Dimensions Height in inches (mm) Shipping Weight in lbs (kg) TX (7.5) 0.9 (3.4) 3/4 in. M 8 (203) 15 5/8 (321) 5 (2.3) TX (16.7) 3.2 (12.1) 3/4 in. M 11 (279) 15 (381) 9 (4.1) TX-25V 10.3 (39) 10.3 (39) 3/4 in. F 15 3/8 (391) 19 1/4 (489) 23 (10.4) TX-30V 14.0 ( (42.8) 3/4 in. F 15 3/8 (391) 27 7/8 (606) 25 (11.3) TX-42V 20.0 (75.0) 11.4 (43.2) 3/4 in. F 15 3/8 (391) 31 5/8 (803) 33 (15.0) TX-60V 34.0 (128.7) 34.0 (128.7) 1 1/4 in. F 22 (559) 29 5/8 (752) 61 (27.7) TX-80V 44.0 (166.6) 33.9 (128.3) 1 1/4 in. F 22 (559) 36 (914) 69 (31.3) TX (234.7) 34.1(129.1) 1 1/4 in. F 22 (559) 46 5/8 (1184) 92 (41.7) TX (333.1) 46.4 (175.6) 1 1/4 in. F 26 (660) 47 1/4 (1200) 123 (55.8) Materials: Steel shell, polypropylene liner, butyl diaphragm. Connection: TX-5, TX-12: brass. TX25 - TX210 stainless steel. Max. operating temperature: 200 F (93 C). Max. operating pressure: 150 psi (1034 kpa). Precharge is 40 psi (276 kpa). TX (598.1) 103 (389.7) 2 in. F 30 (762) 74 1/2 (1892) 626 (283.9) TX (798.7) 107 (405.0) 2 in. F 30 (762) 92 1/2 (2350) 760 (344.7) TX (999.3) 172 (651.1) 3 in. F 36 (914) 85 5/8 (2175) 810 (267.4) TX (1200.0) 206 (779.8) 3 in. F 36 (914) 98 (2489) 914 (414.6) TX (1400.6) 241 (912) 3 in. F 36 (914) 110 3/8 (2804) 1018 (461.8) TX (1577.4) 275 (1041.0) 3 in. F 48 (1219) 81 7/8 (2680) 1655 (750.7) TX (1998.2) 344 (1302.2) 3 in. F 48 (1219) 95 3/4 (2432) 1925 (873.2) Materials: Steel shell, butyl bladder. Connection: Bronze. Max. operating temperature: 240 F (115 C). Max. operating pressure: 150 psi (1034 kpa). Precharge is 40 psi (276 kpa)
5 Table 4. ASME Construction Product Number Tank Volume in gal. (L) Maximum Acceptable Volume in gal. (L) Connection Size NPT Diameter in inches (mm) Dimensions Height in inches (mm) Shipping Weight in lbs (kg) TX-5-C 2.1 (7.9) 0.86 (3.3) 3/4 in. M 10 (254) 10 3/8 (264) 21 (9.8) TX-12-C 4.7 (17.8) 2.6 (9.8) 3/4 in. M 12 (305) 12 1/2 (318) 34 (15.4) TX-20V-C 7.6 (28.8) 2.6 (9.8) 3/4 in. F 12 (305) 20 3/4 (527) 49 (22.2) TX-30V-C 12.5 (47.3) 10.0 (37.9) 3/4 in. F 16 1/4 (413) 17 1/4 (438) 84 (38.1) TX-42V-C 17.5 (47.3) 11.4 (43.2) 3/4 in. F 16 1/4 (413) 24 1/4 (616) 98 (44.5) TX-60V-C 25.0 (94.6) 11.3 (42.8) 3/4 in. F 16 1/4 (413) 34 (864) 125 (56.7) TX-80V-C 53.0 (200.6) 34.5 (130.6) 1 1/4 in. F 24 (610) 40 1/2 (1029) 190 (86.2) TX-180-C 77.0 (291.5) 33.9 (128.3) 1 1/4 in. F 24 (610) 52 5/8 (1337) 255 (115.7) TX-210-C 88.0 (333.1) 34.3 (129.8) 1 1/4 in. F 24 (610) 60 (1524) 295 (133.8) Materials: Steel shell, polypropylene liner, butyl diaphragm. Connection: Stainless steel. Max. operating temperature: 200 F (93 C). Max. operating pressure: 150 psi (1034 kpa). Precharge is 40 psi (276 kpa). TX-451-C (598.1) 103 (389.7) 2 in. F 30 (762) 74 1/2 (1892) 626 (283.9) TX-452-C (798.7) 107 (405.0) 2 in. F 30 (762) 92 1/2 (2350) 760 (344.7) TX-453-C (999.3) 172 (651.1) 3 in. F 36 (914) 85 5/8 (2175) 810 (267.4) TX-454-C (1200.0) 206 (779.8) 3 in. F 36 (914) 98 (2489) 914 (414.6) TX-455-C (1400.6) 241 (912) 3 in. F 36 (914) 110 3/8 (2804) 1018 (461.8) TX-456-C (1577.4) 275 (1041.0) 3 in. F 48 (1219) 81 7/8 (2680) 1655 (750.7) TX-457-C (1998.2) 344 (1302.2) 3 in. F 48 (1219) 95 3/4 (2432) 1925 (873.2) Materials: Steel shell, butyl bladder. Connection: Bronze. Max. operating temperature: 240 F (115 C). Max. operating pressure: 150 psi (1034 kpa). Precharge is 40 psi (276 kpa)
6
7
8 Automation and Control Solutions Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN Toronto, Ontario M1V 4Z9 customer.honeywell.com U.S. Registered Trademark 2007 Honeywell International Inc J.I
L404F,T,V PressureTrol Controllers
L404F,T,V PressureTrol Controllers PRODUCT DATA FEATURES Models available in a series of control ranges, and pressure scales in kpa and psi. All models automatically reset and have an adjustable differential.
The ES /118 Explosion-Proof Housings
Explosion-Proof Housings The ES-650-117/118 Explosion-Proof Housings are used to enclose Modutrol Motors used in hazardous locations. NEMA 7 and NEMA 9 enclosures. Housing meets NEC requirements for Class
V5197A Firing Rate Gas Valve
V5197A Firing Rate Gas Valve FEATURES PRODUCT DATA APPLICATION The V5197A is a firing rate valve used to provide variable flow control of air, natural gas, liquefied petroleum (LP), and manufactured gases.
ML6425, ML7425 Spring Return Electric Linear Valve Actuators
ML645, ML745 Spring Return Electric Linear Valve Actuators PRODUCT DATA EATURES APPLICATION The ML645 Spring Return Electric Linear Valve Actuators are floating control actuators used with controllers
C7046A,B,C,D Air Temperature Sensors
C7046A,B,C,D Air Temperature Sensors FEATURES PRODUCT DATA APPLICATION The C7046 series of Air Temperature Sensors function as primary and/or secondary sensors in electronic control systems. C7046A,C Sensors
V51E Butterfly Valve. The valve mechanism is equipped with strain release springs.
Butterfly Valve The V51E Butterfly Valve is a firing rate valve used to provide variable flow control of natural, liquefied petroleum (LP), and manufactured gases. It is also applicable to controlling
Q5020A-D Globe Valve Linkages FOR DIRECT COUPLED ACTUATORS
Q5020A-D Globe Valve Linkages FOR DIRECT COUPLED ACTUATORS FEATURES PRODUCT DATA Used with 2- and 3- globe valves in modulating or two-position service. Used with 25, 50, and 142 lb-in. spring return and
V5011N Two-Way Threaded Globe Valve
VN Two-Way Threaded Globe Valve FEATURES PRODUCT DATA Red brass body with NPT-threaded end connections. Low seat leakage rate (. percent C v ). : rangeability per VDI/VDE 7. Spring-loaded, self-adjusting
D690 Round Damper LOW-LEAKAGE, SINGLE-BLADE FEATURES APPLICATION PRODUCT DATA. Contents
D690 Round Damper LOW-LEAKAGE, SINGLE-BLADE FEATURES PRODUCT DATA Neoprene and silicone seal for tight closing and low leakage. Oilite bearings for long life. 90-degree damper travel for a variety of applications.
Immersion Wells and Compression Fittings FOR TEMPERATURE CONTROLLERS
Immersion Wells and Compression Fittings FOR TEMPERATURE CONTROLLERS FEATURES PRODUCT DATA 107324A ELEMENT HOLDER APPLICATION 121371B IMMERSION WELL 112632AA IMMERSION WELL 104484A COMPRESSION FITTING
ML7421A,B Electric Linear Valve Actuator
ML7421A,B Electric Linear Valve Actuator FEATURES PRODUCT DATA Quick and easy installation. No separate linkage required. 3/4 in. (20 mm) stroke on ML7421A; 1-1/2 in. (38 mm) stroke on ML7421B. No adjustments
AT120A-E; AT140A-E; AT150A,B,D-F; AT160B; AT175A-D,F Transformers
AT0A-E; AT0A-E; AT50A,B,D-F; AT60B; AT75A-D,F Transformers FEATURES PRODUCT DATA AT0 is rated at 0 VA. AT0 is rated at 0 VA. AT50 is rated at 50 VA. AT60 is rated at 60 VA. AT75 is rated at 75 VA. All
Series 41 and 81 Modutrol IV Motors
Series 4 and 8 Modutrol IV Motors PRODUCT DATA FEATURES APPLICATION The Series 4 and Series 8 Modutrol IV Motors are 2-position (line- and low- voltage control, respectively) spring-return motors. They
ML6420, ML7420 Non-Spring Return Electric Linear Valve Actuators
ML640, ML740 Non-Spring Return Electric Linear Valve Actuators EATURES Quick and easy installation. No separate linkage required. Conduit connector is standard. No adjustments required. Low power consumption.
V9055A,D Modulating Fluid Power Gas Valve Actuator
V9055A,D Modulating Fluid Power Gas Valve Actuator PRODUCT DATA APPLICATION The V9055 Gas Valve Actuator in combination with a V5055, VE5000 a or V5097 Gas Valve provides modulating control of the gas
V5011N Two-Way Threaded Globe Valve
VN Two-Way Threaded Globe Valve FEATURES PRODUCT DATA Red brass body with NPT-threaded end connections. Low seat leakage rate (. percent of C v ). : rangeability per VDI/VDE 7. Spring-loaded, self-adjusting
Q5024A,B Globe Valve Linkages FOR DIRECT COUPLED ACTUATORS
Q5024A,B Globe Linkages FOR DIRECT COUPLED ACTUATORS PRODUCT DATA Heavy-duty steel rack pinion construction aluminum die-cast housing. Maintenance-free construction. Flexible actuator mounting orientation.
Q7800C Integrated Burner Control Subpanel
Q7800C Integrated Burner Control Subpanel PRODUCT DATA Q7800C1001: Single fuel, on/off control, RM7800/RM7840, RM7895/RM7896. Q7800C1019: Dual fuel, on/.off control, RM7800/RM7840, RM7895/RM7896. Q7800C107:
Commercial Thermal Expansion Tanks. For Closed Thermal Water Systems
Commercial Thermal Expansion s For Closed Thermal Water s mtrol thermal expansion tanks are engineered to control pressure build-up in closed, potable water systems. vailable in diaphragm, full acceptance
Immersion Wells and Compression Fittings FOR TEMPERATURE CONTROLLERS
Immersion Wells and Compression Fittings FOR TEMPERATURE CONTROLLERS FEATURES PRODUCT DATA 107324A ELEMENT HOLDER APPLICATION 121371B IMMERSION WELL 112632AA IMMERSION WELL 104484A COMPRESSION FITTING
V5055A-F Industrial Gas Valves
V5055A-F Industrial Gas Valves FEATURES PRODUCT DATA APPLICATION The V5055 Gas Valves are used with the V4055, V406, and V9055 Fluid Power Actuators to control gas flow to commercial and industrial burners.
V5013B,C,F Three-Way Mixing and Diverting Valves
V50,C,F Three-Way Mixing and Diverting Valves FETURES PRODUCT DT Mixing or diverting models. ronze body with threaded connections or cast iron body with flanged-end connections. Stainless steel stem and
ML6420, ML7420 Non-Spring Return Electric Linear Valve Actuators
ML640, ML740 Non-Spring Return Electric Linear Valve Actuators EATURES Quick and easy installation. No separate linkage required. Conduit connector is standard. No adjustments required. Low power consumption.
FEATURES APPLICATION PRODUCT DATA
M640,M740F,M6435,M7435F ctuators V5852, V5853, V5862, V5863 Valves 40.5 L (80N) NON-SPRING ND SPRING RETURN CTUTORS ND /2 INCH, 3/4 INCH CRTRIDGE GLOE VLVES FETURES PRODUCT DT Small size allows installation
MS4120F, MS4620F, MS8120F, S2024-F, S20230-F Fast-Acting, Two-Position Actuators
MS4120F, MS4620F, MS8120F, S2024-F, S20230-F Fast-Acting, Two-Position Actuators FEATURES PRODUCT DATA 175 lb-in. (20 N m) minimum driving torque at 350 F (176 C). Reversible mounting facilitates use in
UV100A Ultraviolet Systems UV100A1000 AND UV100A1018 AIR TREATMENT SYSTEMS UV100A1059 AND UV100A2008 SURFACE TREATMENT SYSTEMS
UV100A Ultraviolet Systems UV100A1000 AND UV100A1018 AIR TREATMENT SYSTEMS UV100A1059 AND UV100A2008 SURFACE TREATMENT SYSTEMS FEATURES PRODUCT DATA APPLICATION When installed in forced air heating and
35 and 70 lb-in. Non-Spring Return Direct Coupled Actuators ML6161, ML7161, ML6174, ML7174
35 and 70 lb-in. Non-Spring Return Direct Coupled Actuators ML66, ML76, ML674, ML774 PRODUCT DATA FEATURES Selectable 45,, or 90 stroke in both clockwise (cw) or counterclockwise (ccw) directions. 0 to
BCS Modutrol Motor M7484A
BCS 7700 Modutrol Motor M7484A The M7484A is a low voltage, reversing proportional modutrol motor used to drive a fuel valve and combustion air damper as commanded by the BCS 7700. Electronic, vibration
R182J, R482J, R845A, R847A, R882J, RA89A, RA832A Switching Relays
RJ, RJ, RA, RA, RJ, RA9A, RAA Switching Relays hese relays provide intermediate or heavy duty service in a wide variety of switching configurations. Relays with V control coils: RlJ, RJ, RA, RA9A, RAA,
Q345A, Q3451, Q3481, Q348A, Q348B, Q362A, Q373A, Q381A and Q3452 Intermittent Pilot Burner/Igniter-Sensors PRODUCT DATA
QA, Q, Q8, Q8A, Q8B, Q6A, QA, Q8A and Q Intermittent Pilot Burner/Igniter-Sensors PRODUCT DATA FEATURES QA, Q8A, Q8B and QA Intermittent Pilot Burner/Igniter-Sensors are compatible with all Honeywell intermittent
V4062A,B,D HI-LO-OFF Fluid Power Gas Valve Actuator
V4062A,B,D HI-LO-OFF Fluid Power Gas Valve Actuator PRODUT DATA APPLIATION The V4062 Gas Valve Actuator in combination with a V5055, VE5000 a or V5097 Gas Valve provides three-position control of the gas
MS4104, MS4109, MS4604, MS4609, MS8104, MS8109 Fast-Acting, Two-Position Actuators
MS4104, MS4109, MS4604, MS4609, MS8104, MS8109 Fast-Acting, Two-Position Actuators FOR FIRE/SMOKE CONTROL APPLICATIONS FEATURES PRODUCT DATA APPLICATION The MS4104, MS4109, MS4604, MS4609, MS8104 and MS8109
VB2, VB3 Ball Valve/Actuator Assemblies
V2, V all Valve/ctuator ssemblies TURS PROUT T V2 V V2 ll Models Sizes from 1/2 in. to 2 in. with internal nominal pipe thread (NPT) connections. qual Percentage flow characteristics. ield configurable
Selection Guide for P Series Pump Accessories & Options
Selection Guide for P Series Pump Accessories & Options Contents Page Calibration Cylinders...2 Back Pressure & Pressure Relief Valves...3 Pulsation Dampeners...6 Motors & Controllers...9 Calibration Cylinders
Q345A, Q3451, Q3481, Q348A, Q348B, Q362A, Q373A, Q381A and Q3452 Intermittent Pilot Burner/Igniter-Sensors
QA, Q, Q8, Q8A, Q8B, Q6A, QA, Q8A and Q Intermittent Pilot Burner/Igniter-Sensors FEATURES PRODUCT DATA QA Q,Q8 Q8A,B Q6A QA QA, Q8A, Q8B and QA Intermittent Pilot Burner/Igniter-Sensors are compatible
C7170A,B Encapsulated Temperature Sensor
C7170A,B Encapsulated Temperature Sensor The C7170A,B Temperature Sensors are for use with electronic controllers where linear PTC sensors are required (W7100, W7600, W7620, or Excel 500, for example),
WELL-X-TROL ASME WATER SYSTEM TANKS
WELL-X-TROL ASME WATER SYSTEM TANKS ASME Water Tanks for Commercial & Industrial Applications WELL-X-TROL ASME: The Professionals Choice Table of Contents The AMTROL Advantage... 2 A Wide Range of Applications...
Applications. residential. light commercial. pressure boosting
Applications residential light commercial Easier to install than steel, and over time, much tougher to beat. pressure boosting Our WM-Series offers features and benefits steel tanks just can t match. From
Series 71, 72, and 76 Modutrol IV Motors
Series 7, 7, and 76 Modutrol IV Motors PRODUCT DATA FEATURES APPLICATION The Series 7, 7 and 76 Modutrol IV Motors are spring return and nonspring return motors used to control dampers and valves. The
V4043 and V4044 Motorized Valves
V03 and V0 Motorized Valves INSTALLATION INSTRUCTIONS FEATURES V0 These valves consist of an actuator motor and valve assembly for controlling the flow of hot or cold water. The V03 provides 2-position,
Tanks. The Industry s Longest Warranty: 7 Years E-1
The Industry s Longest Warranty: 7 Years Dome Projection Welded Air Valve Eliminates threaded valve leak paths. Tamper-evident warning label for added safety. WARRANTY 7YEAR NEW High Strength Steel (HSS)
SPECIFICATION: OPERATION: (Dimensional drawing on following page)
Electronic Showers Hardwire Operated (86T) - Push button electronic shower system Model No: 86T7 COMPLIES WITH: SPECIFICATION: ASME A.8. / CSA B. Volume Control lever handle ADA compliant to ICC / ANSI
MV100 Electric Controllers T100, T200 Thermostatic Controllers and V2000 Radiator Valves
MV100 Electric Controllers T100, T200 Thermostatic Controllers and V2000 Radiator Valves PRODUCT DT THERMOSTTIC CONTROLS T100 T100M PPLICTION The MV100, T100, T200 Controllers, when paired with V2000 Radiator
V5013N Three-Way Threaded Globe Valve
VN Three-Way Threaded Globe Valve FETRES PRODCT DT Red brass body with NPT-threaded connections. Stainless steel stem and brass plug. ow seat leakage rate (. percent of C v ). Spring-loaded, self-adjusting
3-way 1/2-2 Globe Valves
Datasheet Overview Designed to work with either an electronic actuator with a 3/4-inch (20 mm) stroke, the three-way globe valves are available in ANSI Class 250 for normally closed or normally open action.
VBN2, VBN3 Control Ball Valves With Threaded Connections
N, N Control all alves With Threaded Connections FETURES PRODUCT DT PPLICTION N... N...D The N Two-Way and the N Three-Way Control all alves control hot and chilled water with glycol solutions up to 0%
AURORA ACCESSORIES EXPANSION TANKS (ASME)
UROR ESSORIES EXPNSION TNKS (SME) 1060 SERIES Section 1060 Page 201 ated MY 2010 1/2" F E H Furnish and install, as shown on the plans, a gal. (L), dia. x long urora 1060 Series plain steel expansion tank.
PRESSURE CONTROL VALVES SABS 198
PRESSURE CONTROL VALVES SABS 198 1 CALVALVE DOUBLE BLOCK Pressure control combined pressure reducing valve and expansion relief valve, copper by copper compression ends. DZR alloy body. Replaceable cartridge
M436A/M836A,B Damper Motors
M436A/M836A,B Damper Motors FEATURES INSTALLATION INSTRUCTIONS APPLICATION M436A/M836A,B Damper Motors are spring return (SR) motors used for residential and light commercial applications in Series 40
Installation Manual DIAPHRAGM WELL TANK
Installation Manual DIAPHRAGM WELL TANK IN-LINE SERIES: 2-5 & 7 GALLON VERTICAL SERIES: 14-20-25-32-36-52-65-86-96-119 GALLON HORIZONTAL SERIES: 7-14 & 20 GALLON NO LEAD NO LEAD: The weighted average of
VBN2, VBN3 Control Ball Valves With Threaded Connections
N, N Control all alves With Threaded Connections FETURES PRODUCT DT PPLICTION N... N...D The N Two-Way and the N Three-Way Control all alves control hot and chilled water with glycol solutions up to 0%
V4062A,B,D HI-LO-OFF Fluid Power Gas Valve Actuator
V406A,B,D HI-LO-OFF Fluid Power Gas Valve Actuator PRODUT DATA APPLIATION The V406 Gas Valve Actuator in combination with a V5055 or V5097 Gas Valve provides three-position control of the gas supply to
Model descriptions. Technical data. Pressure and Temperature Limits Models 19, 20, 20P: -60 to 406 F Models 19M, 20M, 20MP:
VALVES & CONTROLS KUNKLE SAFETY AND RELIEF PRODUCTS Non-code Bronze Liquid Relief Valves Model descriptions Model 20 Model 19: All bronze, equipped with handwheel for easy adjustment within spring ranges.
T&S BRASS AND BRONZE WORKS, INC.
Saddleback Cove / P.O. Box 088 Travelers Rest, SC 9690 B-0708 Travelers Rest, SC: 800-476-403 Simi Valley, CA: 800-43-050 Fax: 864-834-358 www.tsbrass.com 4 7/6" 3mm This Space for Architect/Engineer Approval
Drawdown Gal L Gal L Gal L. Horizontal Tanks
E36 Pressure Tanks Pressure Tanks - Steel For use wherever pressurized tanks are needed in water system applications Controlled water cell Heavy duty gauge steel construction Warranty: 5 year limited Total
LIQUIDYNAMICS 1:1, 3:1 and 5:1 RATIO AIR OPERATED OIL PUMPS
This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. LIQUIDYNAMICS 1:1, 3:1 and 5:1 RATIO AIR OPERATED OIL PUMPS Instruction & Parts Manual This manual covers the following
PASSAIC COUNTY TECHNICAL INSTITUTE CCA 1422 NEW S.T.E.M. BUILDING 2017
SECTION 221119 - DOMESTIC WATER PIPING SPECIALTIES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Vacuum breakers. 2. Backflow preventers. 3. Water pressure-reducing valves. 4. Balancing valves.
Date: Project #: Engineer: Prepared By: Bid Date:
NEOTHERM Hydronic Boiler NTH Hydronic Boiler Indoor Sizes 285-850 Date: Submittal Data Project #: Engineer: Project Name: Prepared By: Location: Bid Date: Contractor: Standard Equipment High condensing
AIR RIDE SUSPENSION SYSTEMS
AIR RIDE SUSPENSION SYSTEMS Solenoid Valves (Fast Valves) Valve Manifold Systems Pressure Switches Filters (Water Traps) Air Bellows & Fittings www.asconumatics.com 1 ASCO Numatics Air Ride Components
D I S T R I B U T E D V A L V E S. TBV Series 21/51 Cryogenic Diverter Ball Valve TBV
TM TBV Series 21/51 Cryogenic Diverter Ball Valve TBV Series 21/51 Cryogenic Diverter Ball Valve incorporates all features found in the 2100 and provides diverting capabilities for use where two or more
See Water Pressure Reducing Valves Catalog (PHBRWPRV) for more detailed information about the products in this section.
See Catalog (PHBRWPRV) for more detailed information about the products in this section. Water pressure reducing valves PR (36LF) Series Residential and commercial applications The Apollo 36LF pressure
TrueDRY DR65/DR90/DR120
TrueDRY DR65/DR90/DR120 Ventilating Dehumidification System DR65 Specifications Part Number: DR65A2000 Blower: Supply Voltage: Amps: 160 CFM @ 0.0 in. WG 100 CFM @ 0.6 in. WG 120 VAC; 60 Hz. 5.2 A Power
See Water Pressure Reducing Valves Catalog (PHBRWPRV) for more detailed information about the products in this section.
See Catalog (PHBRWPRV) for more detailed information about the products in this section. WATER PRESSURE REDUCING VALVES PR (36LF) SERIES RESIDENTIAL AND COMMERCIAL APPLICATIONS The Apollo 36LF pressure
SentronicPLUS IO-Link CLASS A Electronic Pressure Regulator. Installation Manual
SentronicPLUS IO-Link CLASS A Electronic Pressure Regulator Installation Manual Sentronic PLUS ASCO NUMATICS Sentronic PLUS Electronic Pressure Regulator Sentronic PLUS is a 3-way proportional valve with
Flowrite 599 Series Three-Way Valves 1/2 to 2-inch Bronze Body
Flowrite 599 Series Three-Way Valves 1/2 to 2-inch Bronze Body Document No. 155-185P25 VF 599-4 Description The Flowrite VF 599 Series ANSI Class 250 three-way valves are designed to work with either a
Masoneilan * Lo-dB Cartridges and Expansion Plates
GE Oil & Gas Technical Specifications 05/2013 Masoneilan * Lo-dB Cartridges and Expansion Plates Table of Contents Introduction...3 Application...3 Lo-dB Cartridges...4 Principle of Operation...4 Installation...4
FINISHED WALL. OPTIONAL TO FINISHED FLOOR USUALLY BETWEEN 1651 AND 1981mm (65 AND 78) OPTION 457 mm (18") 25mm (1) MIN.
PRESSURE BALANCE BATH/SHOWER FAUCET Volume and Temperature Control Valve Available Trim Kits Colony Soft Colony Soft FloWise Moments Reliant 3 Ceramix Princeton R120 Valve Body Shown Jasmine Copeland Green
A. This Section includes the following domestic water piping specialties:
SECTION 221119 - DOMESTIC WATER PIPING SPECIALTIES PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following domestic water piping specialties: 1. Backflow preventers. 2. Water pressure-reducing
W91/W94 Series TEMPERATURE REGULATORS. Self-Operated Temperature Regulators. Design & Operation W91 Non-Indicating W94 Dial Thermometer
Design & Operation W91 Non-Indicating W94 Dial Thermometer Watson McDaniel reserves the right to change the designs and/or materials of its products without notice. 2010 Watson McDaniel Company CAPILLARY
Paramax Series Control Ball Valve. Specification Data CM6004 7/97
Paramax Control Ball Valve Specification Data CM6004 7/97 Table of Contents Numbering System........................ 3 Specifications............................ 4 Seal Ring Limitations......................
Bladder Accumulators. Bladder Accumulators Introduction. Bladder IN THIS SECTION. Features. Models, Capacities & Dimensions. 10 cu in to 15 gallons
Overview ntroduction N TS SECTON Overview 51 Specifications 52, Capacities & Dimensions Bottom Repairable 54 Top Repairable 55 igh-flow 56 Transfer Barrier 57 Bottles 58 Options & Accessories 59 Replacement
Pulsation Dampeners (Chargeable-Adjustable)
ACCU-PULSE (Chargeable-Adjustable) Canadian 2018 List 01/18 Rev. 6 TABLE OF CONTENTS Page Page 2 Dampener Sizing Guide 7 ACCU-PULSE Series III (370cu in) 3 ACCU-PULSE Series I (10cu in) 8 ACCU-PULSE Series
HYDAC ACCUMULATORS DEVELOPMENT AND ENGINEERING
HYDAC ACCUMULATORS HYDAC accumulators - a name synonymous with advanced technology, design, manufacturing and application engineering for more than 35 years. As an essential element in modern hydraulics,
Series 61 and Series 62 Modutrol IV Motors
Series 6 and Series 6 Modutrol IV Motors PODUCT DATA APPLICATION The Series 6 and Series 6 Modutrol IV Motors are three-wire spring return and non-spring return floating control motors. Use these motors
Installation, Operation & Maintenance Instructions for MF-Solar Series Solution Feeders
INDUSTRIES LIMITED Installation, Operation & Maintenance Instructions for MF-Solar Series Solution Feeders Startup Procedure 1) Close isolation valve between feeder and system connection point 2) Fill
Electronic Faucet - 591T Series
Electronic Faucet - 591T Series 4" Cast Lavatory Specification: (example) (4") electronic faucet CAST one-piece body with integral waterproof sensor and connector Polished chrome plated trim Battery (4
Q7130A, Q7230A, Q7330A Modutrol IV Interface Modules
Q70A, Q70A, Q70A Modutrol IV Interface Modules EATURES INSTALLATION INSTRUCTIONS Q70A APPLICATION Q70A Q70A The Q70, Q70, and Q70 Modutrol IV Interface Modules are used with Series 90 Modutrol IV Motors
05 Water Pressure Systems INTRODUCTION
52 05 Water Pressure Systems INTRODUCTION Pressure Controlled Diaphragm Pumps Pressure controlled diaphragm pumps provide boat owners with a fresh water system that is as easy to use as their domestic
Penberthy Automatic Injectors
Hot water injectors used primarily as boiler feed pumps but also in numerous other applications for pumping liquids and discharging at high pressure and temperature Features Durable construction. Compact
Kerotest N-Series Needle Valves CRN Approved
K1514 K5534 Product Brief The N-Series is designed for processing plants, oil and gas production, hydraulic and pneumatic equipment, testing labs, and other minimally corrosive applications. Features/Benefits
SECTION Pressure & Temperature Control
16 Pressure & Temperature Control ARMSTRONG PRODUCT CATALOGUE 70 Pressure Reducing s Pressure Reducing s Armstrong pressure reducing valves (PRVs) and temperature regulators help you manage steam, air
DODGE COOL LUBE 2 for Sleevoil Pillow Blocks Part Numbers , , ,
DODGE COOL LUBE for Sleevoil Pillow Blocks Part s 063487, 063488, 07889, 07890 These instructions must be read thoroughly before installing or operating this product. WARNING: To ensure the drive is not
SECTION DOMESTIC-WATER PACKAGED BOOSTER PUMPS
SECTION 221123.13 - DOMESTIC-WATER PACKAGED BOOSTER PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
V5013N Three-Way Threaded Globe Valve
VN Three-Way Threaded Globe Valve FETRES PRODCT DT Red brass body with NPT-threaded connections. Stainless steel stem and brass plug. ow seat leakage rate (. percent C v ). Spring-loaded, self-adjusting
Includes electric operated valve Pressure gauge with siphon, vacuum breaker and air vent BOILER UNITS
STEAM / HOT WATER MODELS HWG FEATURES A. O. Smith hot water generators are available for operation with steam or boiler water as the energy source. They are completely assembled with components sized,
Flowrite 599 Series Three-Way Valves 1/2 to 2-inch Bronze Body
Flowrite 599 Series Three-Way s 1/2 to 2-inch Bronze Body Technical Instructions Document No. 155-185P25 VF 599-4 Description The Flowrite VF 599 Series ANSI Class 250 three-way valves are designed to
S Series Technical Data...7 How to Order...8 Dimensions...8 Manifold Dimensions and Part Numbers...9
Miniature Valve Series............................................................3-14 RB Series..................................................................................3-6 Technical Data...................................................................................3
Horizontal Pre-Piped Bladder Tanks with Proportioner
DATA SHEET Horizontal Pre-Piped Bladder Tanks with Proportioner Features Pre-piped configurations with a wide selection of proportioner sizes, including the ANSUL FLOWMAX CL for closed-head sprinkler systems
Flowrite VF 599 Series Three-Way Valves 1/2 to 2-inch Bronze Body
PRODUCT NO. MODEL LANDIS & STAEFA ASSEMBLED IN U.S.A. Flowrite VF 599 Series Three-Way Valves 1/2 to 2-inch Bronze Body Document No. 155-185P25 VF 599-4 Cv VF186R1 Description The Flowrite VF 599 Series
TECHNICAL DATA OBSOLETE
March 21, 2008 Foam 180a 1. DESCRIPTION The Viking bladder tank consists of an inner tank (bladder) fabricated of a flexible material (Buna-N over nylon) and an outer tank fabricated from carbon steel.
E8 Mini-Matic 3/8" Bolted Plastic Pumps Operating Instructions
E8 Mini-Matic 3/8" Bolted Plastic Pumps Operating Instructions Polypropylene SAFETY WARNINGS Read these instructions completely before installation and start-up. It is the responsibility of the purchaser
Powers Controls Powertop Two-Way Valves Normally Open
Powers Controls Powertop Two-Way s Normally Open VP 658-5 Description The VP 658 normally open valves are pneumatically operated valves designed to control the flow of both water and steam. Features Stainless
Vertical Pre-Piped Bladder Tanks with Proportioner
DATA SHEET Vertical Pre-Piped Bladder Tanks with Proportioner Features Pre-piped configurations with a wide selection of proportioner sizes, including the ANSUL FLOWMAX CL for closed-head sprinkler systems
Air Line Filtration Accessories. Bulletin /USA. Finite
Air Line Filtration Accessories Bulletin 1300-150/USA Finite Finite s Featured Air Line Filtration Accessories For a comprehensive list and to find out where these accessories are used, please see pages
Raptor 085HB-270HB & 155CB Submittal
Raptor 085HB-270HB & 155CB Submittal Residential High Efficiency Gas s RPTR085HB, 110HB, 155HB, 205HB, 270HB, 155CB RPTR Wall Mount and Floor Standing Heating s Wholesaler Job Name Mechanical Contractor
Flowrite 599 Series Two-Way Valves, 1/2 to 2- inch Bronze Body, ANSI 250
Flowrite 599 Series Two-Way Valves, 1/2 to 2- inch Bronze Body, ANSI 250 Technical Instructions Document No. 155-184P25 VF 599-3 Description The Flowrite 599 Series two-way valves are designed to work
STUDIO S BATH ACCESSORIES TOWEL BARS
STUDIO S BATH ACCESSORIES TOWEL BARS MODEL NUMBER: 7105.018-18" Towel Bar 7105.024-24" Towel Bar Available Finishes 002 Polished Chrome 295 PVD Brushed Nickel 2" 2" 3-7/8" (99 mm) 18" (457 mm) 2" 2" 3-7/8"
How to Specify NH-39
Index Application Product Recommendation Backwater Valves 4200, 4300 Trap Primers 4401, 4402 Bladder Type Trap Seal Device 4405 Water Control Valve & Box 4440 Deep Seal P-Traps 4450 Adapters 4455, 4456
Date: Project #: Engineer: Prepared By: Bid Date: 30 psi pressure relief valve 50 psi pressure relief valve 60 psi pressure relief valve
NEOTHERM Hydronic Boiler NTH Hydronic Boiler Date: Indoor Sizes 285-850 Submittal Data Project #: Engineer: Project Name: Prepared By: Location: Bid Date: Contractor: Standard Equipment Large LCD display
Dust Caps Plastic with wire harness
Screw-to-connect Couplings TLX Range COUPLINGS AND NIPPLE Body Size Connection Part No. Dimension locking Weight sleeve ex Coupling Nipple Zoll Dash Description Type Standards Coupling Nipple (mm) (inch)