Accreditation. a'1" ul. ( oar.hl,.n" Deutsche Akkreditieru ngsstelle G m bh. Y,/.,n" r,nn" Head of Division

Transcription

1 ( oar.hl,.n" Akkreditieru ngsstel le Deutsche Akkreditieru ngsstelle G m bh Entrusted according to Section 8 subsection 1 AkkStelleG in connection with Section 1 subsection 1 AkkStellecBV Signatory the Multilateral Agreements of EA, ILAC and IAF for Mutual Recognition Accreditation The Deutsche Akkreditierungsstelle GmbH attests that the testing laboratory HESSEL Ingenieu rtechnik GmbH Am Münsterwald 3,52L59 Roetgen is competent under the terms of DIN EN ISO/IEC L7025:2005 to carry out tests in the following fields: mechanical-technological testing and methods for the analysis of the long-term behaviour of thermoplastic products The accreditation certificate shall only apply in connection with the notice of accreditation of with the accreditation number D-PL and is valid until lt comprises the cover sheet, the reverse side of the cover sheet and the following annex with a total of 3 pages. Registration number of the certificate: D-PL Berlin, I,/ a'1" ul Y,/.,n" r,nn" Head of Division This document is a translation. The definitive version is the original German accreditation certificate See notes overleaf.

2 l Deutsche Akkreditierungsstelle GmbH German Accreditation Body Office Berlin Spittelmarkt Berlin Office Frankfurt am Main Gartenstraße Frankfurt am Main The publication of extracts of the accreditation certificate is subject to DAkkS Deutsche Akkreditierungsstelle GmbH. Exempted is the disseminations of the cover sheet by the conformity No impression shall be made that the accreditation attested by DAkkS. the scope of on the Accreditation Body (Federal Law Gazette I p. 2625) and the REGULATION (EC) No 765/2009 OF THE AND OF THE COUNCIL of 9 July 2008 setting out the requirements for surveillance relating to the marketing of products (Official Journal of 18 of 9 July 2008, p. 30). DAkkS is a signatory to the Multilateral Agreemen ofthe European co-operation for Accreditation (EA), International ational Laboratory Accreditation Co-operation (l LAC). The ise each others' accreditations. öh be retrieved from the following websites: EA: ILAC: IAF:

3 +,j";::;q:; (?ou*il=,*.",., " gsste,, e Deutsche Akkreditieru ngsstelle GmbH German Accreditation Body Annex to the Accreditation Certificate D-PL according to DIN EN ISO/IEC 17025:2005 Period of validity: to 08.L Holder of certificate: HESSEL Ingenieurtechnik GmbH Am Münsterwald 3,52159 Roetgen Tests in the fields: mechanical-technological testing and methods for the analysis of the long-term behaviour of thermoplastic products Abbreviations used: see last page DIN EN 128L4-3 Testing of welded joints of thermoplastics semi-finished products L0 Part 3: Tensile creep test Including: Annex A.l-: Full notch creep test (FNCT) Annex A.2: Two notch creep test (2NCT) Annex B: Minimum creep rupture time of the parent material for applicability of the long term welding factor Annex C: Testing of socket joints DIN EN ISO 1133 Plastics - Determination of the melt mass-flow rate (MFR)and the melt volume-flow rate (MVR) of thermoplastics DVS Testing of welded joints of thermoplastics plates and tubes - L997-O7 Tensile creep test DVS Testing of welded joints of thermoplastic sheets and pipes - Supplement 1 Tensile creep test - Testing of socket joints 200L-t2 This document is a translation. The definitive version is the original German annex to the accreditation certificate.

4 Annex to the accreditation certificate D-PL-l (=; kks Deutsche Akkreditieru ngsstel le DVS Supplement 2 200L-L2 PA 2NCT o4 PA FNCT PA ACT s-09 PAS PAPLP PAPLP PA PEN PA WA L-03 PA PEN PA PEN L-03 Testing of welded joints of thermoplastic sheets and pipes - Tensile creep test - Testing of the resistance to slow crack growth using the Full Notch Creep Test (FNCT) Two Notch Creep Test (2NCT) following DIN EN 128L4-3: , Annex A.2 Full Notch Creep Test (FNCT) following DIN EN t28l4-3: , Annex A.L Accelerated Creep Test (ACT) - Accelerated test method to verify the creep rupture strength of polyolefins (validation included) Pipes made from Polyethylene for alternative installation techniques - Dimensions, Technical Requirements and Testing lnternal pressure tests of thermoplastic pipes with additional locally concentrated external load (point load, linear load) according to PAS 1075, Annex 43 Accelerated internal pressure tests of thermoplastic pipes with additional locally concentrated external load (point load, linear load) following to PAS 1075, Annex A3 Penetration test according to PAS 1075, Annex A4 Thermal stability of pipes in terms of a required service life - Thermal aging test following to PAS 1075, Annex A5 Accelerated notch test on full walled pipes (Notch pipe testing) following DIN EN ISO External protective layer scratch test according to PAS 1075, Annex A6 each in connection with: VA MAC VA MSL Operating procedure for the definition of testing conditions according to Modified Arrhe ni u s Co nce pt ( MAC), va lidatio n included Operoting procedure to determine the minimum service life (MSL) of polyethylene components Period of validity: to Translation 213

5 Annex to the accreditation certificate D-Pt KS VlilH:["",""ssstere VACMP Operating procedure to manufacture specimen from compression moulded plotes following EIN EN ISO : and EN ISO 293: abbreviations used: ACT CMP NPT PA PAS PEN PLP SMR VA WA Accelerated creep test Compressed moulded plate Notch pipe test HESSEL test procedure Publicly available specification Penetration test Point load test External protective layer scratch test H ESSEL operating procedure Thermalaging Period of validity: to Translation 313