Wall/Slot -II 85N Recessed Perimeter

Size: px

Start display at page:

Download "Wall/Slot -II 85N Recessed Perimeter"

Jeffrey Harper
5 years ago
Views:

1 Type: Project: Wall/Slot -II 85N Recessed Perimeter Specifications 10 1/2 (267 ± 19) 9" (229) baffle shown in flush F/position 3 5/8" (92) FIXTURE SUPPORT RAIL. Extruded white aluminum, wall-mounted rail provides continuous support and true alignment of fixtures and components. Rail is designed to provide a reveal at the wall to compensate for irregularities in wall construction. Galvanized splines are included for continuous alignment. A hook-and-lock system provides quick installation and horizontal adjustment. FIXTURE HOUSING. Components are manufactured using computer-controlled dies to assure precise tolerance. Housing is with an 18-gauge steel integrated rear support channel having captive leveling screws to provide field adjustment. FIXTURE REFLECTOR SHIELDS. Die-formed 24-gauge steel having a continuous channel at ceiling juncture with locking and splining clips for attaching to ceiling trims. Shields are designed to provide 1 1/2" vertical adjustment. LAMPING. Available in one- and two-lamp T8. BALLAST. Electronic Ballast (ELB), high power factor, thermally protected Class P, Sound Rated A, less than 10% THD, manufactured by a UL Listed manufacturer, as available, determined by Litecontrol. Ballasts with a voltage range of 120 to 277 will be used when fixture configuration and ballast availability allow. The minimum number of ballasts will be used. CEILING TYPE. Compatible with most types of ceiling systems, including grid and plaster. Fixture system must be installed prior to installation of ceiling. Finish of wall should extend 11" above finished ceiling height. See Wall/Slot-II Pre-Installation Manual for specific ceiling type details. CERTIFICATION. Fixture and electrical components shall be UL and/or CUL Listed and shall bear the I.B.E.W., A.F. of L. label. Note: Litecontrol reserves the right to change specifications without notice for product development and improvement. Ordering guide Product, lamping, & length 85N T8 - Options S/ BW - CWM - G - ELB - EF Series Lamp Count Nominal Length(ft) Lamp Type Shielding Position Diffuser Finish Ceiling Type Ballast Other options Volts 85N 1, 2 1, 2 1, 2 2, 4 2, 4 notes Cross-section lamping T8 1-T8 1-T8 2-T8 Parabolic Reflector S/ R/ F/ Shielding position BW PBSS PAT.12(XA) FP Diffusers CWM (Matte White) is standard G CT CZ DP Ceiling type ELBis standard DA-ELB HEL/ELB ECO/ELB Ballast options EF F PR TW DS SDS Other options 85N14T8-S/BW-CWM-G-ELB-EF-120 is a typical catalog number for a 1-lamp (1 lamp in cross-section), 4-foot long T8 fixture with blade baffle shielding at top, Matte White finish, for mounting in a lay-in ceiling, electronic ballast, emergency fluorescent ballast,120 volts notes: Lamp Count = total number of lamps in the fixture Tandem Wiring not available for one-lamp cross-section fixtures For Ordering guide information in shaded areas, choose selection by reading ACROSS the shaded areas for correct specifications. Questions to Ask or 277 volt? 2. Row information, including desired fixture lengths? 3. Diffuser type? 4. Tandem wiring? 5. Ceiling type? 6. Other options? litecontrol.com

2 Shielding position / Open*. No shielding is used at the ceiling opening. S/ Shielding at Top. A baffle or lens diffuser may be used just below the lamp (S/position) to shield lamps from view while maintaining a clean, floating appearance. R/ Regressed. Baffle or lens diffuser is positioned above ceiling line, to shield the lamp and fixture from view. Baffle regressed 1"; lens 1 3/4". PR one-lamp version only. F/ Flush. Baffle is positioned flush with the ceiling to complete the ceiling plane. Len regressed 3/4". PR one-lamp version only. * There is no designation required for open shielding position. Diffusers BW Blade Baffle. S/position: White, 3/4" high x 3/4" OC, 20-gauge steel. Linear shielding is 45. R/ or F/positions: White, 1 1/2" high x 1 1/2" OC, 20-gauge steel. Linear shielding is 45. PBSS Parabolic Baffle. R/ or F/position: semi-specular anodized aluminum, 1.4" high x 2" OC. Linear shielding is 40. PAT. 12 (XA) Lens. Diagonal 3/16" conical prisms,.100" thick extruded acrylic. FP Lens. White acrylic diffuser,.100" thick. Note: Leave both Shielding position and Diffuser choice blank for OPEN - no shielding option. Ceiling type A. Photometric data B. G Lay-in CT Concealed Tee CZ Concealed Zee DP Drywall/Plaster Specify the applicable ceiling trim. Detailed fixture shield information is available from your sales representative. Ballast options Specify in place of ELB, contact factory for availability: DA/ELB Advance Mark VII Dimming Ballast. HEL/ELB Osram Sylvania Helios Dimming Ballast. ECO/ELB Lutron ECO-10 Dimming Ballast. EF F PR TW DS SDS Other options Emergency Fluorescent Ballast. Battery-powered ballast from a UL Listed manufacturer will operate one T8 lamp for 1 1/2 hours. Fuse. Slow or fast blow, determined by Litecontrol. Parabolic Reflector. Specular aluminum reflector for additional downward light projection. Only available with one-lamp fixtures. Tandem Wiring. For two-lamp cross-section fixtures wired to switch in-line lamps separately, providing two levels of light. Double Shields. Specify when a corridor intersects a row of Wall/Slot. Not intended for use as row fixtures in ceilings. Special Depth Shield. Standard fixture height is. A lower height shield is available for installations where obstructions occur. Contact factory for details. System connectors Catalog Number Series - Connector - Finish Description (Minimum-Maximum along wall in parenthesis) 85N EC CWM 85N SE CWM 85N IC CWM 85N OC CWM 85N ASE CWM 85N AIC CWM 85N AOC CWM 85N AEC CWM End Cap Straight Extension (2"-12") Inside Corner - 90 (11"-21") Outside Corner - 90 (2"-11") Angular Straight Extension (2"-11") Angular Inside Corner (6"-15") Angular Outside Corner (2"-11") Angular End Cap 85N-AOC-CWM is a typical catalog number for an angular outside corner connector. Corners, extensions, and end caps, when added to fixtures, permit continuous wall-to-wall installation. Finish: CWM (Matte White). Mitered baffles are supplied for corners when Regressed or Flush baffles are specified. Lengths are field cut. C. D. E. F. A. 85N14T8 50% wall reflectance Litecontrol Certified Test Report # B. 85N24T8 50% wall reflectance Litecontrol Certified Test Report # C. 85N14T8-F/BW 50% wall reflectance Litecontrol Certified Test Report # D. 85N24T8-F/BW 50% wall reflectance Litecontrol Certified Test Report # E. 85N14T8-S/BW 50% wall reflectance Litecontrol Certified Test Report # F. 85N24T8-S/BW 50% wall reflectance Litecontrol Certified Test Report # For complete photometric information, website. Click on Quick Find 85n litecontrol.com note: A technical sheet with additional... an details, employee illustrations, owned and photometric company data is available online for Wall/Slot-II. 100 Hawks Avenue Hanson MA FAX info@litecontrol.com litecontrol.com

3 SYSTEM CONNECTORS Catalog Number Series - Connector - Finish Description (Minimum/Maximum along wall in parenthesis) 85N EC CWM End Cap 85N SE CWM Straight Extension (2"-12") 85N IC CWM Inside Corner - 90 (11"-21") 85N OC CWM Outside Corner - 90 (2"-11") 85N ASE CWM Angular Straight Extension (2"-11") 85N AIC CWM Angular Inside Corner (6"-15") 85N AOC CWM Angular Outside Corner (2"-11") 85N AEC CWM Angular End Cap PLAN VIEW IC AOC AIC ASE 85N-AOC-CWM is a typical catalog number for an angular outside corner connector. Corners, extensions, and end caps, when added to fixtures, permit continuous wall-to-wall installation. Mitred baffles are supplied for corners when Regressed or Flush baffles are specified. Lengths are field cut. SE OC

4 SHIELDING POSITION Specify position S/, R/, or F/, followed by correct shielding type. Example: R/BW OPEN No shielding is used at the ceiling opening for maximum efficiency when the lamps cannot be viewed from below. -/ Position one-lamp only not available with shielding at lamp OPEN: No Shielding 85N14T8 - G - ELB OPEN: Parabolic Reflector 85N14T8 - G -ELB - PR SHIELDING AT TOP A baffle or lens diffuser may be used just below the lamp - S/ position - to shield lamps from view while maintaining a clean, floating appearance. S/ Position OPEN: Shielding At Top 85N14T8 - S/BW - G - ELB REGRESSED Baffle or lens diffusers are positioned above ceiling line, to shield the lamp and fixture from view. R/ Position regression of baffles 1", lenses 1 3/4" one-lamp only regression of baffles 1", lenses 1 3/4" Regressed Shielding 85N14T8 - R/BW - G - ELB Regressed Shielding - Parabolic Reflector 85N14T8 - R/BW - G - ELB - PR -120 FLUSH Baffles are positioned flush with the ceiling to complete the ceiling plane. F/ Position flush mounted baffles; regression of lenses 3/4" one-lamp only flush mounted baffles; regression of lenses 3/4" Flush Shielding 85N14T8 - F/BW - G -ELB Flush Shielding - Parabolic Reflector 85N14T8 - F/BW - G - ELB - PR - 120

5 SHIELDING TYPES BW Blade Baffle PBSS Parabolic Baffle BW Blade Baffles. S/ position: White, 3/4" high x 3/4" OC, 20-gauge steel. Linear shielding is 45. R/ or F/ positions: White, 1 1/2" high x 1 1/2" OC, 20-gauge steel. Linear shielding is 45. PBSS Parabolic Baffles. R/ or F/ position: semi-specular anodized aluminum, 1.4" high x 2" OC. Linear shielding is 40. PAT. 12 (XA) Lens. Diagonal 3/16" conical prisms,.100" thick extruded acrylic. FP Lens. White acrylic diffuser,.100" thick. Lens or Diffuser (various types available) BALLAST OPTIONS Specify in place of ELB, contact factory for availability: DA-ELB ELB10 Electronic ballast, same specification as "Ordering Guide", HEL/ELB except less than 10% THD. ECO/ELB MKV/ELB Advance Mark V electronic ballast. CEILING TYPE Advance Mark VII dimming ballast. Motorola Helios dimming ballast. Lutron ECO-10 dimming ballast. G Lay-in CT Concealed Tee CZ Concealed Zee DP Drywall/Plaster Specify the applicable ceiling trim. Detailed fixture shield information is available from your sales representative. OTHER OPTIONS DS Double Shields Specify when a corridor intersects a row of Wall/Slot. Specify DS in OTHER OPTIONS column. Not intended for use as row fixtures in ceilings. SDS Special Depth Shield Standard fixture height is. A lower height shield is available for installations where obstructions occur. Specify SDS in OTHER OPTIONS column and contact factory. EF F TW OTHER ELECTRICAL OPTIONS Emergency fluorescent ballast. Battery-powered ballast from a UL Listed manufacturer will operate one T8 lamp in a 3', 4' or 8' fixture for 1 1/2 hours. Fuse. Slow or fast blow, determined by Litecontrol. Tandem Wiring. For two-lamp cross-section fixtures wired to switch in-line lamps separately, providing two levels of light.

6 PLANNING FOR INSTALLATION PRE-INSTALLATION NOTES: Finish of wall should extend 11 above ceiling. Continuous Fixture Support Rail is provided for ease of installation. Locate bottom of rail X dimension from bottom of ceiling, table below. Ceiling construction must be supported independently of the lighting system. Straight Extension Inside Corner Fixture Support Rail furnished in 8-foot lengths, extruded aluminum for easy cutting T-bar clips Field-cut filler pieces, lay in Outside Corner Ceiling support wires, by others End Cap Ceiling X Dimension Lay-in Grid T-Bar Concealed T-bar 7 1/8" Concealed Z-bar Tegular Grid T-Bar 7 1/8" + Tile Regression Drywall/Plaster 7 1/8" + Ceiling Thickness Wall Angle. Furnished in 8-foot lengths, field cut to length. For use with F/ and R/ position baffles Ceiling system supplied by others, must be self-supporting and provide ceiling trim member for the fixture Reflector Shield Reflector Shield has 1 1/2" vertical adjustment Reflector Shield Extension Fixture interconnection by others x bottom of ceiling 1. Install Fixture Support Rails on walls. 2. Hook fixtures on rail and slide into position. 3. Install extensions and corners. 4. Attach Reflector Shields to fixtures and components. PHOTOMETRIC DATA: No Shielding N14T8 50% wall reflectance Litecontrol Certified Test Report # N24T8 50% wall reflectance Litecontrol Certified Test Report #

7 PHOTOMETRIC DATA: F/ Position Shielding (Flush) N14T8-F/BW 50% wall reflectance Litecontrol Certified Test Report # N14T8-F/PBSS 50% wall reflectance Litecontrol Certified Test Report # N24T8-F/BW 50% wall reflectance Litecontrol Certified Test Report # N24T8-F/PBSS 50% wall reflectance Litecontrol Certified Test Report #

8 PHOTOMETRIC DATA: S/ Position Shielding N14T8-S/BW 50% wall reflectance Litecontrol Certified Test Report # N14T8-S/XA 50% wall reflectance Litecontrol Certified Test Report # N24T8-S/BW 50% wall reflectance Litecontrol Certified Test Report # N24T8-S/XA 50% wall reflectance Litecontrol Certified Test Report #

Fixture Type: Project Name: Baffle or Diffuser. Lamp Type. BW FP PARSS (1-lamp D only) PBSS XA 6044 (ADW only) see Baffle and Diffusers Options

Fixture Type: Project Name: Baffle or Diffuser. Lamp Type. BW FP PARSS (1-lamp D only) PBSS XA 6044 (ADW only) see Baffle and Diffusers Options W-D-66N 1" (25) 6 1/2" (165) Fixture Type: Project Name: Mod 66 W-D-66N, W-ID-66N, W-ADW-66N (chalkboard) Wall-Mounted Product Description Linear modular luminaire which offers a variety of distributions