Phoenix Manufacturing, Inc E. Roeser Rd. Phoenix, AZ phoenixmanufacturing.com

Transcription

1 3655 E. Roeser Rd. Phoenix, AZ phoenixmanufacturing.com MODELS: SPECIFICATION DATA INDUSTRIAL AEROCOOL 12 & 8 MODELS ID/IS 500 w/ WS080 or WS100 or WS144 ID/IS 601 w/ WS080 or WS100 or WS144 IS/IS/IUP 701 w/ WS080 or WS100 or WS144 ID/IS/IUP 800 w/ WS880 or WS812 or WS844 (UL Models Use U as Prefix; ex.: UID500) Aerocool Industrial Evaporative Coolers Feature: Metal Skids under each dry module for roof mounting. Lift brackets are supplied for lifting to installation site. Each dry module comes with belt included. Models ID/IS 500 require 1 wet section, therefore 1 pump. Models ID/IS/IUP 601, 701, 800 require 2 pumps. Knockout for electrical service is 7/8. Bottom pan drain is 3/4 male hose thread Units are UL Listed to UL Standard 507 High quality architectural grade Peblar XT finish Galvanized sheet steel is zinc coated at weight rated G40 or G90 Multi-layer bottom pan finish Up to 25,000 CFM capacity Three Phase EISA motors are NEMA MG-1 table compliant Belt & float included Bearings have an L10 bearing life of 39,600 hours PERFORMANCE AIR DELIVERY - data published and derived from test conducted in accordance with A.M.C.A (Air Movement and Control Assoc.) standard 210. BEARING LIFE - L10 bearing life of 39,600 hours is based on ABMA standard 9/ISO standard 281. MOTORS - recognized under UL component standard #1004 for motor certification. SINGLE PHASE MOTORS - tested under UL standard 507 for locked rotor and heat rise protection. THREE PHASE MOTORS - EISA motors are NEMA MG-1 table construction. PUMPS - recognized under the UL standard #778 for operating water pumps with thermal overload and locked rotor protection. EVAPORATIVE MEDIA - specifically corrugated cellulose material, impregnated with insoluble anti-rot salts and rigidifying saturates. Media used in UL Listed cooler is rated to UL900, Class 2. SEALANT - water immersion per ASTM D870. FLEXIBILITY - per ASTM D756. HOT DIPPED GALVANIZED SHEET STEEL - is ASTM A653, type CS, with zinc coating weights rated G40 or G90. CORROSION RESISTANCE - per ASTM B117. POLYMERIC MATERIALS - listed in accordance with UL 94 and 746C. CONSTRUCTION PENCIL HARDNESS - per ASTM D3363. IMPACT RESISTANCE - per D2794. FLEXIBILITY - per ASTM D522. SURFACE BURNING CHARACTERISTICS- of building materials (best rating) per UL 723 and ASTM E-84. PEBLAR XT - is our one coat TGIC Polyester Powder Coating system that is applied over 5 stage zinc phosphate prepared sheet steel surfaces for protection against atmospheric corrosion. This coating system meets the requirement of UL organic coatings for steel enclosures of outdoor use electrical equipment. UL Listed models also available. To specify and order a U.L. Listed model add a U prefix to the front of the appropriate model number. UL Classified Models The Aerocool Trophy models are Classified by UL as Evaporative Air Coolers inaccordance with the Uniform mechanical Code. Phoenix Manufacturning certifies that the evaporative coolers shown are licensed to bear the AMCA seal. Cooler ratings are based on tests performed in accordance with AMCA publication 211 and comply with the requrements of the AMCA Certified Rating Program. All data, specifications and detail contained in this publication are intended as a general guide for using PHOENIX MANUFACTURING, INC. products. These products should not be used in design or construction without an independent evaluation by a qualified engineer or architect to verify the suitability of a particular product for use in a specific application. PHOENIX MANUFACTURING, INC. assumes no liability for failure resulting from the use or misapplication of computation, detail drawings and specifications contained herein. This publication contains the latest information available at the time of printing. PHOENIX MANUFACTURING, INC. reserves the right to make modifications and/or change materials of any of their products without prior notice or obligation. PHOENIX MANUFACTURING, INC. may not produce all of the products contained in this submittal. For product availability and the latest information regarding products contact PHOENIX MANUFACTURING, INC.

2 Performance shown is installation Type B - Free Inlet, duct outlet. Power Rating (B.H.P.) includes transmission losses. Performance ratings include the effects of evaporative media in the airstream. Standard 8 Wet Sections Certified Air Delivery at Various External Static Pressures - Blower RPM values based on motor RPM AMCA Licensed External Static Pressure - inches H2O ID CFM UP TO 9,875 3/4 6, , , , , , , , , , , , , , , , , , , , , , WS /2 8, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , IS CFM UP TO 9,875 3/4 6, , , , , , , , , , , , , , , , , , , , , , WS /2 8, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ID/IS CFM UP TO 17,100 WS , , , , , , , , , , , /2 10, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , /2 17, , , , , , , , , , , ID/IS/IUP CFM UP TO 19,750 WS , , , , , , , , , , , /2 12, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , /2 19, , , , , , , , , , , OPERATION NOT RECOMMENDED IN THIS AREA, WATER ENTRAINMENT WILL OCCUR. 19, , , , , , , ID/IS/IUP CFM UP TO 25, , , , , , , , , , , , , , , , , , , , , , , WS , , , , , , , , , , , /2 23, , , , , , , , , , , , , , , , , , , , , , Do not exceed listed rpm, motor current draw (FLA) will be less than nameplate. Water entrainment may occur if operated at higher rpm s than indicated. Operation in high static pressure - low CFM conditions can lead to motor RPM fluctuation

3 8 Standard Media Economical choice - Lower Replacement Cost ID500 w/ WS080 - Airflow Data IS500 w/ WS080 - Airflow Data ID/IS601 w/ WS080 - Airflow Data ID/IS/IUP701 w/ WS080 - Airflow Data CFM LIMIT ID/IS/IUP800 w/ WS880 - Airflow Data

4 Performance shown is installation Type B - Free Inlet, duct outlet. Power Rating (B.H.P.) includes transmission losses. Performance ratings include the effects of evaporative media in the airstream. Standard 12 Wet Sections Certified Air Delivery at Various External Static Pressures External Static Pressure - inches H2O - Blower RPM values based on motor RPM AMCA Licensed ID CFM UP TO 9,875 3/4 6, , , , , , , , , , , , , , , , , , , , , , WS /2 8, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , IS CFM UP TO 9,875 3/4 6, , , , , , , , , , , , , , , , , , , , , , WS /2 8, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ID/IS CFM UP TO 16, , , , , , , , , , , , /2 9, , , , , , , , , , , , , , , , , , , , , , WS , , , , , , , , , , , , , , , , , , , , , , /2 16, , , , , , , , , , , ID/IS/IUP CFM UP TO 19, , , , , , , , , , , , /2 11, , , , , , , , , , , , , , , , , , , , , , WS , , , , , , , , , , , , , , , , , , , , , , /2 19, , , , , , , , , , , , , , , , , , , , , , ID/IS/IUP CFM UP TO 25, , , , , , , , , , , , , , , , , , , , , , , WS , , , , , , , , , , , /2 23, , , , , , , , , , , , , , , , , , , , , , Do not exceed listed rpm, motor current draw (FLA) will be less than nameplate. Water entrainment may occur if operated at higher rpm s than indicated. Operation in high static pressure - low CFM conditions can lead to motor RPM fluctuation

5 12 Standard Media Ultra Efficient - More surface area for better cooling ID500 w/ WS100 - Airflow Data IS500 w/ WS100 - Airflow Data ID/IS601 w/ WS100 - Airflow Data ID/IS/IUP 701 w/ WS100 - Airflow Data STATIC PRESSURE - INCHES H 20 CFM LIMIT ID/IS/IUP800 w/ WS812 - Airflow Data

6 Specification of critical components is vital in obtaining the required discharge volume through the unit. Motor horsepower, voltage, motor shaft outside diameter, motor sheave outside and inside diameter all directly relate to the revolutions per minute (RPM) of the blower wheel. Equally important is the reduction in electrical usage and water required for operation. Performance data is for installation Type B - free inlet, ducted outlet. Power Rating (B.H.P.) for the ID/IS/IUP800 with Wet Section WS844 does not include transmission losses. Performance ratings include the effects of evaporative media. Power Rating (B.H.P.) DOES Include Transmission Losses Ultra-efficient 4x4 Wet Sections Air Delivery at Various External Static Pressures External Static Pressure - inches H2O - Blower RPM values based on motor RPM 1725 ID CFM UP TO 9,100 3/4 5, , , , , , , , , , , , , , , , , , , , , WS /2 7, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , IS CFM UP TO 9,750 3/4 6, , , , , , , , , , , , , , , , , , , , WS /2 7, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ID/IS CFM UP TO 15, , , , , , , , , , , , /2 8, , , , , , , , , , , , , , , , , , , , , , WS , , , , , , , , , , , , , , , , , , , , , , /2 15, , , , , , , , , , , ID/ISIUP CFM UP TO 19, , , , , , , , /2 10, , , , , , , , , , , , , , , , , , , , WS , , , , , , , , , , , , , , , , , , , , , , /2 18, , , , , , , , , , , , , , , , , , , , , , Power Rating (B.H.P.) DOES NOT Include Transmission Losses ID/IS/IUP CFM UP TO 24, , , , , , , , , , , , , , , , , , , , , , , WS , , , , , , , , , , , /2 22, , , , , , , , , , , , , , , , , , , , , , Operation in high static pressure - low CFM conditions can lead to motor RPM fluctuation

7 4 x 4 Hi-Density Media Highest efficiency provides for the most cooling ID500 w/ WS144 - Airflow Data IS500 w/ WS144 - Airflow Data ID/IS601 w/ WS144 - Airflow Data ID/IS/IUP701 w/ WS144 - Airflow Data ID/IS/IUP800 w/ WS844 - Airflow Data

8 Engineering Data Dimensional information for the Aerocool Industrial Coolers with 12 media, 8 media and the Ultra-Efficient 4x4 media. Single Inlet Discharge 500 Series Inlet Discharge 601, 701 & 800 Series 12 Standard Media Model Number Cabinet Dimensions (Inches) H W D Wet Duct Opening Drain Loc. Water Svc. Media Skid Location Belts Cab A B C X D E S F G H I J K L M N O P Q QTY SIDE DOWN UP Dia x Width Ship Weight Oper. Weight Blower Wheel Blower Pulley Pitch Diameter ID / /8 17 1/4 11 1/8 N/A / / /2 4 1/2 2 1/2 1 1/8 N/A 1 A80 A77 N/A X 24 IS / /8 N/A 11 1/8 16 3/ / / /2 4 1/2 2 1/2 1 1/8 N/A 1 A80 A77 N/A X 24 ID / /8 17 1/4 11 1/8 N/A / / /2 1 7/8 2 1/2 1 1/8 25 1/4 2 A98 A98 N/A x 24 IS / /8 N/A 11 1/8 19 3/ / / /2 1 7/8 2 1/2 1 1/8 25 1/4 2 A98 A98 N/A x 24 ID/IS / /4 31 3/4 14 7/8 8 5/8 17 3/ / / /2 1 7/8 2 1/2 1 5/8 22 7/8 2 A90 A85 N/A x 28 IUP / /4 31 3/4 13 3/4 8 5/8 N/A / / /2 1 7/8 2 1/2 1 5/8 22 7/8 2 N/A N/A A x 28 ID/IS/IUP / / / / / / /2 6 2 /12 1 5/8 26 5/8 2 A105 A90 A , x Single 13 Single 8 Standard Media & 4x4 Media Model Number Cabinet Dimensions (Inches) H W D Wet Cab Duct Opening Drain Loc. Water Svc. Media Skid Location Belts A B C X D E S F G H I J K L M N O P Q QTY SIDE DOWN UP Dia x Width Ship Weight Oper. Weight Blower Wheel Blower Pulley Pitch Diameter ID / /8 17 1/4 11 1/8 N/A / / /2 4 1/2 2 1/2 1 1/8 N/A 1 A80 A77 N/A X 24 IS / /8 N/A 11 1/8 16 3/ / / /2 4 1/2 2 1/2 1 1/8 N/A 1 A80 A77 N/A X 24 ID / /8 17 1/4 11 1/8 N/A / / /2 1 7/8 2 1/2 1 1/8 21 1/4 2 A98 A98 N/A x 24 IS / /8 N/A 11 1/8 19 3/ / / /2 1 7/8 2 1/2 1 1/8 21 1/4 2 A98 A98 N/A x 24 ID/IS / /4 31 3/4 14 7/8 8 5/8 17 3/ / / /2 1 7/8 2 1/2 1 5/8 18 7/8 2 A90 A85 N/A x 28 IUP / /4 31 3/4 13 3/4 8 5/8 N/A / / /2 1 7/8 2 1/2 1 5/8 18 7/8 2 N/A N/A A x 28 ID/IS/IUP / / / / / / /2 1 5/8 22 5/8 2 A105 A90 A , x Single 13 Single

9 Sheave Selection All sheaves listed are adjustable to meet the blower speed RPM requirements for your application. Using the model number combined with the motor horsepower and blower RPM, use this chart to locate the corresponding part number in the far right column. Motor Selection Motors of varying voltages and identical horsepower may have different motor shaft sizes. Be certain the motor shaft diameter and motor sheave bore size are the same size. All single phase motors are thermally protected and do not require starting devices. Motors which are 3 Phase 1 HP and greater, are high efficiency motors that meet or exceed U.S. E.I.S.A. (Energy Independence & Security Act) Technical Motor Specifications Model No. H.P. Therm. Pro Phase Volt Amperage Base Frame M180 3/4-2 spd. X Resilient 56 5/8 M161 3/4 X / / 5.3 Resilient 56 5/8 M163 3/ / / 1.4 Resilient 56 5/8 M spd. X Resilient 56 5/8 M165 1 X / / 7.0 Resilient 56 5/8 M * 240 / / 1.6 Rigid 143T 7/8 M Rigid 143T 7/8 M spd. X Resilient 56 5/8 M /2 X / / Resilient 56H 5/8 M /2 3 * 240 / / 2.4 Rigid 145T 7/8 M / Rigid 145T 7/8 *M172 2 X / / Resilient 56H 5/8 M * 240 / / 3.0 Rigid 145T 7/8 M Rigid 145T 7/8 Shaft Dia. M * 240 / / 4.0 Rigid 182T 1 1/8 M Rigid 182T 1 1/8 M / / 6.3 Rigid 184T 1 1/8 M Rigid 184T 1 1/8 M /2 3 * 240 / / 9.3 Rigid 213T 1 3/8 M * 240 / / 12.2 Rigid 215T 1 3/8 Sheave Selection Model Number Motor H.P. Bore Blower RPM - Sheave Turns Open ID/IS 500 3/4, 1, 1 1/2, 2 5/ S1 PMI Part ID/IS 500 1, 1 1/2, 2 7/ S1A ID/IS 500 3/4,1, 1 1/2, 2 5/ S2 ID/IS 500 1, 1 1/2, 2 7/ S2A ID/IS 500 3/4, 1, 1 1/2, 2 5/ S3 ID/IS 500 1, 1 1/2, 2 7/ S3A ID/IS 500 1, 1 1/2, 2 5/ S4A ID/IS 500 1, 1 1/2, 2 7/ S4 ID/IS / S3B ID/IS / S4B ID/IS 601 1, 1 1/2, 2 5/ S6A ID/IS 601 1, 1 1/2, 2 7/ S6 ID/IS 601 1, 1 1/2, 2 5/ S8A ID/IS 601 1, 1 1/2, 2 7/ S8B ID/IS 601 1, 1 1/2, 2 5/ S9A ID/IS 601 1, 1 1/2, 2 7/ S9B ID/IS / S8 ID/IS 601 3, 5 1 1/ S9 ID/IS / S10A ID/IS /2 1 3/ S10 ID/IS /2 1 3/ S12 ID/IS/IUP 701 1, 1 1/2, 2 5/ S5A ID/IS/IUP 701 1, 1 1/2, 2 7/ S5 ID/IS/IUP 701 1, 1 1/2, 2 5/ S6A ID/IS/IUP 701 1, 1 1/2, 2 7/ S6 ID/IS/IUP 701 1, 1 1/2, 2 5/ S8A ID/IS/IUP 701 1, 1 1/2, 2 7/ S8B ID/IS/IUP / S7 ID/IS/IUP 701 3, 5 1 1/ S8 ID/IS/IUP 701 3, 5 1 1/ S9 ID/IS/IUP /2 1 3/ S8C ID/IS/IUP /2, / S9C ID/IS/IUP / S10 ID/IS/IUP / S5A ID/IS/IUP / S5 ID/IS/IUP / S6A ID/IS/IUP / S6 ID/IS/IUP / S8A Pump Specifications Pump Model Volts Amps Watts GPM at 5 Head PK60LA PK62LA Alternative Belt Kits Unit Number Motor H.P. Kit Number IS Belt A83 ID Belt A79 Note: ID/IS static pressure and higher requires belt change to above ID/IS/IUP / S8B ID/IS/IUP 800 3, 5 1 1/ S7 ID/IS/IUP 800 3, 5 1 1/ S8 ID/IS/IUP /2, / S8C ID/IS/IUP / S9C! WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to

10 SUBMITTAL DATA Project: Location: Date: Architect: Engineer: Contractor: Submitted by: Ref. No. Cooler Model No. Quantity CFM Static Pressure HP Volts Phase Notes: All data, specifications and detail contained in this publication are intended as a general guide for using PHOENIX MANUFACTURING, INC. products. These products should not be used in design or construction without an independent evaluation by a qualified engineer or architect to verify the suitability of a particular product for use in a specific application. PHOENIX MANUFACTURING, INC. assumes no liability for failure resulting from the use or misapplication of computation, detail drawings and specifications contained herein. This publication contains the latest information available at the time of printing. PHOENIX MANUFACTURING, INC. reserves the right to make modifications and/or change materials of any of their products without prior notice or obligation. PHOENIX MANUFACTURING, INC. may not produce all of the products contained in this submittal. For product availability and the latest information regarding products contact PHOENIX MANUFACTURING, INC.