238in WIDE x 96in H. SINGLE-SIDED FRAME CONVERTS DOWN TO 10ft FRAME

Transcription

1 9 PLESE ER TO LST PGE OF MNUL FOR SEG INSTRUTIONS 0 NOTES: UNLESS OTHERWISE SPEIFIE. NUMERE LLOONS MTH THE NUMERE LELS ON EH PRT URING SSEMLY.. SSEMLY TIME: HOUR WITH PERSONS.. FEET MY VRY. in WIE x 9in H. SINGLE-SIE FRME ONVERTS OWN TO 0ft FRME WG. NO. SLE: : onvert 0ft to 0ft SSF SHEET OF

2 STEP STEP REMOVE REMOVE (TRNSFORMER ) (TRNSFORMER ) REMOVE REMOVE REMOVE ONVERTING STEPS FROM 0FT OWN TO 0FT SLE: : WG. NO. onvert 0ft to 0ft SSF SHEET OF

3 STEP STEP SLIE TOGETHER N RE-TTH FOR 0ft 0 ONVERTING STEPS FROM 0FT OWN TO 0FT SLE: : WG. NO. onvert 0ft to 0ft SSF WEIGHT: SHEET OF

4 STEP INSIE TOP VIEW TRNSFORMER TRNSFORMER TRNSFORMER TRNSFORMER INSIE OTTOM VIEW 0 FT LIGHT MOULES WITH TRNSFORMERS WG. NO. 0ft to 0ft Light Module iagram SLE: : SHEET OF

5 ETIL SLE : PLES STEP GOES K TO TRNSFORMER (TOP FRMES) GOES K TO TRNSFORMER (OTTOM FRMES) ISONNET MLE N FEMLE ONNETORS FROM OTH TOP N OTTOM FRMING INSIE TOP VIEW ISONNET MLE N FEMLE ONNETORS ISONNET MLE N FEMLE ONNETORS ISONNET - FROM TRNSFORMER ISONNET MLE N FEMLE ONNETORS ISONNET - FROM TRNSFORMER ISONNET MLE N FEMLE ONNETORS INSIE OTTOM VIEW WIRING RE-ONNET ONVERTING 0ft to 0ft WG. NO. 0ft to 0ft Light Module iagram SLE: : WEIGHT: SHEET OF

6 INSIE TOP VIEW 0 STEP ONNET MLE - FEMLE ONNETORS (TOP and OTTOM ENTER FRMES) TRNSFORMER ETIL SLE : TRNSFORMER INSIE OTTOM VIEW WIRING RE-ONNET ONVERTING to 0ft WG. NO. SLE: : WEIGHT: 0ft to 0ft Light Module iagram SHEET OF

7 ETIL SLE : ETIL SLE : TURN TO LOK N ERSE TO UNLOK ETIL SLE : ETIL SLE : WG. NO. SLE: :0 Universal -0 Ft SSF SHEET OF

8 E H G F TURN TO LOK N ERSE TO UNLOK ETIL G SLE : ETIL E SLE : TURN TO LOK N ERSE TO UNLOK TURN TO LOK N ERSE TO UNLOK ETIL F SLE : ETIL H SLE : WG. NO. SLE: :0 Universal -0 Ft SSF SHEET OF

9 J ETIL J SLE : WG. NO. SLE: :0 Universal -0 Ft SSF SHEET OF

10 Silicone Edge Graphics (SEG) Installation Instructions into hardware What are Silicone Edge Graphics (SEG)? SEG are dye-sublimation fabric graphics with silicone strips sewn along the underside of the fabrics edge. SEG frames have grooves along their perimeter designed to snugly hold the silicone strips so the fabric can be stretched across the frame for a drum-tight fit. Rubber beading sewn to fabrics edge ont d. : Working in enters again, Go back and press the silicone edge once again on each side previous center, on all sides. Repeat this process, (WORKING IN ENTERS) until the SEG fabric s edge is pressed aproximately every inches apart. EXMPLE: x frame (using this procedure) will have been pressed/tucked times (not including corners) on each side of the frame. PRESS We recommend laying the frame on the floor, then draping the fabric graphic on top. The following procedure ensures the silicone edge will be place evenly over the entire frame and NOT STRETH or GROW at the corners. Once all the edges have been secured, you should have a taut fit with a smooth flat finish. : With lean Hands, Press SEG silicone edge first, into the corners of the frame. INORRET WY PRESS : fter all has been pressed into your frame using this procedure, lightly tap your forefinger to smooth fabric between the tucks. TP INWRS ORRET WY RE INSTRUTIONS ue to the fine quality, smoothness and weave of the fabric, great care must be taken to extend the life of your SEG fabric graphics. Example: x frame We recommend very loosely folding your graphic, making sure there are no hard creases or folds or that the fabric doesn t catch on sharp obects. Store in a clean bag. plastic bag or pillow case is ideal. Graphics can also be spot cleaned with a damp cloth. To wash entire graphic, use a commercial size front loading washing machine on gentle cycle with cool water. o NOT dry clean. You can also gently iron the back side using the Polyester setting of your iron. : Working in enters. Go back and press the silicone edge into the center - on eachside of the frame. EXMPLE: 0 x0 fabric/frame would be pressed in locations. PRESS ISE 0/0 0/0 ISE 0/0