Copyright 2011, MTS Medication Technologies. All rights reserved. MTS USA MTS UK MTS GERMANY

Transcription

1

2 Copyright 2011, MTS Medication Technologies. All rights reserved. MTS USA MTS UK MTS GERMANY

3 Table of Contents INTRODUCTION... 3 THE ROLL OF AN OPERATOR... 3 LOCATING THE AUTOBOND... 3 SETTING UP THE AUTOBOND MACHINE... 4 SAFETY INSTRUCTIONS... 5 WHO SHOULD OPERATE THE AUTOBOND... 5 Precautions... 5 SAFETY AND INFORMATION SYMBOLS IN THIS MANUAL... 6 Machine Safety Labels... 6 Machine Safety... 7 System Safety - Devices... 7 Suggested Lockout Procedure... 8 SYSTEM COMPONENTS... 8 AUTOBOND CONTROLS... 9 Timer / Temperature Control... 9 Temperature Control... 9 Air Regulator Air Regulator Control OPERATING THE AUTOBOND Operating Parameters Operating the Seal Buttons Seal Area... 11

4 Paddle(S) and Paddle Guides SEALING CARD(S) MAINTENANCE Weekly Maintenance Air Regulator MONTHLY MAINTENANCE TROUBLESHOOTING Sealer Issues Blister or medication sealed directly to Seal Plate Cards not sealing adequately Loss of power Fuse Holder Paddle has jammed Air Cylinder CONTACTING MTS... 16

5 Introduction The Roll of an Operator Locating the Autobond

6 Setting Up the Autobond Machine Left (L) and Right (R) Paddle Guides Screws attached for shipping Attach screws from the underside

7 Safety Instructions Who Should Operate the Autobond Precautions Do not attempt to operate or perform any maintenance on this equipment until you have followed all safety precautions. If you have any question, contact your supervisor before doing any operation, work, or maintenance on this equipment. Only authorized and trained personnel should operate the machine.

8 Safety and Information Symbols in this manual Symbol Caution! Definition Important. Machine Safety Labels Symbols Definition

9 Machine Safety System Safety - Devices Lit when ON NOTE: In a sealer EMERGENCY turning the ON/OFF Control to OFF will cause the seal plate to immediately return to the UP position. NOTE: Disengaging the air supply will cause the seal plate to drift down to the seal the position.

10 Suggested Lockout Procedure System Components On/Off Control 5 Temperature Control 2 Sealer Dual Operating Buttons (Left) 6 Seal Time Selector 3 Air Regulator 7 Paddle Support Guides 4 Sealer Air Cylinder 8 MTS Cork Paddle with 6 Handle

11 Autobond Controls Autobond Control Panel Machine ON / OFF Control Punch Card Setting-8 Seconds Unit Dose Card Setting-3 Seconds Temperature Controller NOTE: In a sealer EMERGENCY turning the ON/OFF Control to OFF will cause the seal plate to immediately return to the UP position. Temperature Control Heating Indicator Light Set Temperature Current Temperature Temperature Up Level Key Mode Key Temperature Down NOTE: The Level Key and the Mode Key are factory set. DO NOT RESET. Deviating the temperature more than 20 + will result in an alarm status AL in the temperature display. Readjust setting within the correct parameters.

12 Air Regulator NOTE: The compressor must provide a minimum of 80psi at all times. Adjustment Knob Up to Unlock Down to Lock

13 Operating the Autobond Operating Parameters Left Side Right Side Dual Seal Buttons Caution! Any modification to the seal buttons could cause a potentially hazardous situation which, if not avoided, could result in minor to serious injury. Caution! Due to the temperature and pinch hazard of the seal area keep clear all hands or fingers.

14 Sealing Card(s) Warning: The paddle should be slid completely into the sealer. Failure to fully insert the paddle could cause the seal plate to jam at an uneven position resulting in damage to the sealer.

15 Maintenance Weekly Maintenance Air Regulator Nipple Monthly Maintenance

16 Troubleshooting NOTE: Before performing any Troubleshooting on the Autobond, follow Lock Out Procedure on page 8. Sealer Issues Cards not sealing adequately

17 Loss of power 0.75 AMP Fuse 8 AMP Fuse

18 Paddle has jammed Air Cylinder and Screws Contacting MTS