Type C Track Circuit Uninterruptable Power Supply
|
|
- Lee Hancock
- 5 years ago
- Views:
Transcription
1 Safetran Systems Instruction & Maintenance Model CXP-3 Type C Track Circuit Uninterruptable Power Supply
2 Instruction & Maintenance Type C Track Circuit Uninterruptable Power Supply Contents Introduction...2 Specifications...3 Installation...4 TroubleShooting...5 Replacement Parts...6 Schematic...7 Notes...8 I & M New 2/95
3 Model CXP-3 Type C Track Circuit Uninterruptable Power Supply The model CXP-3 Type C Track Circuit Uninterruptable Power Supply (UPS) employs a track feed transformer, power transfer relay, and standby inverter in a single housing. The CXP-3 acts as a track feed transformer when the circuit is operated with 115 VAC input power. In the event of AC power interruption, the CXP-3 converts standby battery power to an output voltage of the same RMS value as the output under normal operating conditions. The output voltage is proportional to the input voltage. The inverter runs in the standby mode. It is turned on by an internal power transfer relay in the event of the AC input power being lost. The inverter uses rugged MOSFET power transistors with the highest available current rating. The operating frequency is kept to within 1 Hz of nominal under any voltage, load, or temperature condition. Surge protection for the solid state circuitry consists of seven separate stages, including MOV's, Transorbs, Zeners, inductors and capacitors. All electronics are isolated from the chassis, giving a 3000 VAC breakdown voltage. The model CXP-3 is capable of operating up to 4 track circuits through 4 separate outputs of 6.3 VAC and 3.5 amperes each. Inputs are provided for both 115 VAC commercial power and 12 VDC standby battery power. The inverter unit is of a high efficiency design to maximize run time on the battery in the event of power failure. The model CXP-3 measures 8 inches in height, 5-1/4 inches in width, 9 inches in depth and weighs 15 pounds. It can be mounted on a standby relay rack, backboard, or shelf. 2
4 Specifications Electrical: Input Current: no load.25a half load 3.5A full load 6.5A Input Voltage: 12.8V Output Voltage: no load 7.3VAC half load 6.2VAC full load 5.6VAC Output Current: 3.5A Maximum Efficiency: 1/4 load 70% half load 89% Output Wave: Square Frequency: no load 60.0Hz half load 60.0Hz full load 60.0Hz Physical: Ambient Temperature: maximum F (71 C) Dimensions: height 9 inches width 5-1/4 inches Exclusive of mounting tabs or terminals depth 9 inches 3
5 Installation 1. The Model CXP-3 should be rack, wall or shelf mounted within a dry, well ventilated housing. Four #10 wood screws are provided. 2. Connect the battery to the input terminals being careful to observe the proper polarity. A buzzing sound should be audible indicating that the inverter is working properly. Leads between the battery and power supply should be No.9 AWG at minimum and should be as short as practicable. 3. Measure the AC output voltage across the output terminals. The value read should be in accordance with the no load specification value. Note that the output voltage will vary proportionally with the input voltage applied. 4. Connect the load to the output terminals and again measure the AC voltage to make certain that it is satisfactory. 5. With power off, connect commercial AC power to the CXP-3 unit between terminals BX and CX as labeled on the cover. Once the power is applied, the internal power transfer relay will pick up, removing power supplied to the inverter and therefore eliminating the buzzing sound created by the inverter. 6. Again measure the AC output voltage across the output terminals to make certain that it is satisfactory. 7. Surge protection for track circuits and AC line should be provided in accordance with Railroad Standard Practice. See application drawing below for recommended surge protection. MODEL CLEARVIEW LIGHTENING ARRESTER (# X) 1T 2T 3T MODEL HEAVY DUTY EQUALIZER (# X) 1TR 2TR 3TR DC MODEL CXP-3 POWER SUPPLY AC 115 VAC/12 VDC INPUT MODEL SP19-2A SURGE PROTECTION NETWORK (# AX) EQUIPPED WITH A MODEL HEAVY DUTY EQUALIZER (# X) MODEL SP20-2A SURGE PROTECTION NETWORK (# AX) EQUIPPED WITH A MODEL AC LINE PROTECTOR (# X) 4
6 Trouble Shooting Trouble encountered with the CXP-3 will generally be contained within the internal solid state inverter as a result of low or no output. The following causes may be responsible and steps are outlined to isolate the cause. 1. Low output or loss of output Check the input to see that it is close to its nominal value. The output AC voltage will vary directly with the input DC voltage. If a low input voltage is responsible, this condition must be corrected. Considerable drop in voltage may occur in the leads between the battery bus and inverter under heavy load conditions. It is for this reason that heavy gauge wire and short leads are recommended on the input. 2. Excessive or short circuited load If this cause is suspected, remove the load and measure the no load voltage of this output. Check to be sure the fuses have not blown. Always replace with fuses of the same type and rating. This reading should be consistent with the no load specification values. If the no load conditions are proper, connect the load through an AC ammeter to see if the drain is excessive. A load current greater than 3.5A per output indicates a faulty or excessive load. Note that at full load the input current requirement may be as much as 10.0A. The battery must be kept well charged to insure that input voltage will be maintained with this load. With a short circuit or very high current load, either fuse can be blown. 5
7 Model CXP-3 Type C Track Circuit Uninterruptable Power Supply Replacement Parts To Order: Specify Description and Part Number Description Part No. Qty. Req'd Schematic Power Supply CXP Side Wrap CXP-3 Power Supply Top Wrap Inverter Transformer 88 VA Choke Coil #11 Wire 10" Leads L 1 Insulating Shield 1-7/16 W/1 Slot Insulating Cap Fuse Holder Fuse 3AG 15 Amp Fuse 3AG 1.5 Amp Varistor 24 Volt Varistor 150 Volt PC Board Assembly CXP-3 w/lead X1 1 Wire Transorb Assembly Unidirectional X 1 Relay 120VAC P&B #PM17AY Screw Wood RD #10 x 3/4 Stl Zinc 5730-RSC 4 6
8 Schematic 7
9 Notes 8
10 Safetran Systems Safetran Systems Corporation 4650 Main Street N.E. Minneapolis, MN (612)
Maintenance Manual 13 AMPERE POWER SUPPLY 19A704647P1-P3. Mobile Communications LBI-31801C
C Mobile Communications 13 AMPERE POWER SUPPLY 19A704647P1-P3 CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALI- FIED PERSONNEL ONLY. TO AVOID ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER
More informationOWNER S MANUAL. Please read installation and operation instruction before using this Power inverter.
OWNER S MANUAL DP AUDIO Model No. DN350 12 Volt DC to 115 Volt AC 150 WATT 300WATT HIGH SURGE POWER INVERTER Please read installation and operation instruction before using this Power inverter. Contents
More informationA1P OPERATING MANUAL
A1P OPERATING MANUAL TABLE OF CONTENTS Introduction... p. 2 Features... p. 2 Description... p. 3 Theory of Operation... p. 3 Installation... p. 4 Electrical Connections... p. 5 Options... p. 6 Warranty...
More informationA6Z OPERATING MANUAL
A6Z OPERATING MANUAL TABLE OF CONTENTS Introduction... p. 2 Features... p. 2 Description... p. 3 Theory of Operation... p. 3 Installation... p. 4 Electrical Connections... p. 5 Options... p. 6 Warranty.p.
More informationMODEL ELC-12/40-CVM-D BATTERY CHARGER
NATIONAL RAILWAY SUPPLY MODEL ELC-12/40-CVM-D BATTERY CHARGER Installing, Operating and Service Instructions for the ELC-12/40-CVM-D Solid State Charger PLEASE SAVE THESE IMPORTANT SAFETY AND OPERATING
More informationTOWER MAXI T SINGLE CONVERSION ON LINE UPS SYSTEMS
INSTRUCTION MANUAL TOWER MAXI T SINGLE CONVERSION ON LINE UPS SYSTEMS September 2000 TOWER UPS DISTRIBUTION (PTY) LTD 1 1. INTRODUCTION T A B L E O F C O N T E N T S 1.1 General Description... 3 1.2 Features...
More informationSUBSTATION EQUIPMENT - Page 1 of 8
BATTERY BANKS 1. GENERAL: JEA utilizes a 125 volt DC system for the control and operation of its transmission and distribution substations. JEA has standardized on lead acid type battery banks to supply
More informationThe Z Series. SCR Power controllers for resistance heating applications. Zero-Fired SCR Power Controllers AMPS VAC
The Z Series Zero-Fired SCR Power Controllers 60-1200 AMPS 120-600 VAC SCR Power controllers for resistance heating applications. ROBICON 1996 Rev. 7/96 Applications Robicon s Z series power controls are
More informationMaxPak Plus Analog DC V S Drive
Three-Phase 3-600 HP non-regenerative and 5-150 HP regenerative drives Designed to accommodate a wide range of industrial requirements, the DC V S Drive has been widely applied worldwide. Selected ratings
More informationInstallation and Operations Manual
Installation and Operations Manual SEI 150/48-SEL-XXX DC-UPS SEI Incorporated 5115 Pegasus Court, Suite Q Frederick, Md 21704 Phone 301-694-9601 Fax 301-694-9608 Email Info@seipower.com Web http://www.seipower.com
More informationA3Z OPERATING MANUAL
A3Z OPERATING MANUAL TABLE OF CONTENTS Introduction... p. 2 Features... p. 2 Description... p. 3 Theory of Operation... p. 3 Installation... p. 4 Electrical Connections... p. 5 Options... p. 6 Warranty...
More information12VDC TO 230VAC INVERTERS
12VDC TO 230VAC INVERTERS 12VDC TO 230VAC INVERTERS MODEL Nos: CI-200 CI-400 CI-600 CI-800 CI-1000 CI-1500 OPERATION & MAINTENANCE INSTRUCTIONS 0706 Thank you for purchasing this CLARKE Power Inverter.
More informationINSTALLATION, OPERATION & MAINTENANCE SERIES ABC11B-120-XX BATTERY CHARGERS
MANUAL NUMBER: 64073 REV: 2 DATE: October 3, 2006 INSTALLATION, OPERATION & MAINTENANCE SERIES ABC11B-120-XX BATTERY CHARGERS AMERICAN BATTERY CHARGING, INC. P.O. BOX 17040 28 MAPLE AVENUE SMITHFIELD,
More informationSDC,Inc. SCR-Regenerative Ac Drive
SDC,Inc WWW.STEVENSDRIVES.COM APPLICATION NOTE #: AN_REG_GEN000 EFFECTIVE DATE: 12 MAR 02 SUPERSEDES DATE: Original NO. OF PAGES: 10 SCR-Regenerative Ac Drive Using a regeneration controller with adjustable-frequency
More informationSALDET SALES & SERVICE, INC. CLINTON TOWNSHIP, MICHIGAN
Form 1254 BRAKETRON Electronic Motor Brake Instructions SALDET SALES & SERVICE, INC. CLINTON TOWNSHIP, MICHIGAN TABLE OF CONTENTS SECTION TITLE PAGE I. Introduction 1 II. Specifications 1 III. Principles
More informationHQST 500W (12V) HQST 1000W (12V) Modified Sine Wave Inverter. User Manual
HQST 500W (12V) HQST 1000W (12V) Modified Sine Wave Inverter User Manual Important Safety Instructions Please read the installation and operating instructions in this manual carefully before using your
More informationWestell FUSE PANEL. Technical Practice N Position Type VDC Floating
530-101760 REV C 0808-03C December 7, 2012 Westell FUSE PANEL Technical Practice 180108-N-0808 8 Position Type 70 130 VDC Floating FEATURES Single floating input distributing power via Type-70 fuses each
More informationREFERENCE MANUAL FORM: MX-TRM-E REL REV MTE
Matrix APAX 380V-415V 50Hz TECHNICAL REFERENCE MANUAL FORM: MX-TRM-E REL. September 2014 REV. 002 2014 MTE Corporation WARNING High Voltage! Only a qualified electrician can carry out the electrical installation
More informationINSTALLATION INSTRUCTIONS FOR Owner's Copy FILTERED AND REGULATED POWER SUPPLY VOLTS DC INPUT: Hz.
103158 March 9, 2011 FOR INDOOR USE ONLY Detex Corporation, 302 Detex Drive, New Braunfels, Texas 78130-3045 (830)629-2900 / 1-800-729-3839 / Fax (830)620-6711 E-MAIL: detex@detex.com INTERNET: www.detex.com
More informationSECTION DC POWER SUPPLY/BATTERY CHARGER
SECTION 26 33 05 PART 1 - GENERAL 1.1 THE REQUIREMENT A. The CONTRACTOR shall provide the single-phase heavy-duty industrial battery charger and all accessories required, complete and operable, in accordance
More informationO W N E R ' S M A N U A L
1500 Watt DC to AC Power Inverter C o n v e r t s 1 2 V D C B a t t e r y P o w e r t o 1 1 0 V A C H o m e P o w e r O W N E R ' S M A N U A L SAVE THESE INSTRUCTIONS The recommended source of power is
More informationDENVER PUBLIC SCHOOLS DESIGN AND CONSTRUCTION STANDARDS This Standard is for guidance only. SECTION MOTORS, STARTERS & DRIVES
PART 0 DESIGN STANDARDS 0.01 GENERAL DESIGN GUIDELINES A. Coordinate starter needs for mechanical equipment prior to 50% CD and confirm again for 100% CD submittal. B. Coordinate temperature controls requirements
More informationDART Charger Product Description, Information and Specification
g Digital Energy DART Charger Product Description, Information and Specification Document Number : PRPI-029 Version : 1.00 Revision : 2 Date : 03.02.11 Classification: NOTICE OF COPYRIGHT & PROPRIETARY
More informationMatrix APAX. 380V-415V 50Hz TECHNICAL REFERENCE MANUAL
Matrix APAX 380V-415V 50Hz TECHNICAL REFERENCE MANUAL WARNING High Voltage! Only a qualified electrician can carry out the electrical installation of this filter. Quick Reference ❶ Performance Data Pages
More informationArt. No. EC-315. Art. No. EC-330. Art. No. EC-340 SWITCH-MODE BATTTERY CHARGER CONTENTS IMPORTANT SAFETY PRECAUTIONS... 2
SWITCH-MODE BATTTERY CHARGER CONTENTS IMPORTANT SAFETY PRECAUTIONS... 2 DESCRIPTION AND FEATURES... 3 CHARGING STAGES... 4 Art. No. EC-315 Art. No. EC-330 Art. No. EC-340 PROTECTIONS... 5 INSTALLATION...
More informationPS24/AC Volt AC 16 Amp
ALTERNATING CURRENT POWER SUPPLY PS24/AC-6 24 Volt AC 6 Amp FEATURES: Mains Fail Relay Output and Indicator. Fuse blow indication and relay output. 6 fused outlets DESCRIPTION: SPECIFICATIONS: Inputs Voltage-
More informationCENTROIDTM. AC Brushless Drive. Product Spec Sheet
4 Axis, up to 2 KW motors Brake Output for each axis Overtemp and Overcurrent Protection All-software Configuration Self-cooled Fiber Optic Control CENTROIDTM AC Brushless Drive Product Spec Sheet AC Brushless
More informationMASTR II/III 12/24V Power Supply 19A149979P1-120 VOLT/60 Hz 19A149979P2-230 VOLT/50 Hz 19A149979P3 220VOLT/60 Hz
Maintenance Manual LBI-38551 Rev. D, May-04 MASTR II/III 12/24V Power Supply 19A149979P1-120 VOLT/60 Hz 19A149979P2-230 VOLT/50 Hz 19A149979P3 220VOLT/60 Hz M/A-COM Technical Publications would particularly
More informationmodel ps600 Address all communications and shipments to: FEDERAL SIGNAL CORPORATION
MODEL: PS600 HZ: 60 A model ps600 installation and service manual for federal model ps600 FEDERAL SIGNAL CORPORATION POWER SUPPLY VOLTS: SERIES: 120VAC FEDERAL SIGNAL CORPORATION UNIVERSITY PARK, IL. U.S.A.
More informationApplications DC Motors Stepping and Servos Solenoid Valves Relays Lamps and Signal Systems Input to On-Board Regulators Some Floppy Disc Drives.
Applications DC Motors Stepping and Servos Solenoid Valves Relays Lamps and Signal Systems Input to On-Board Regulators Some Floppy Disc Drives a c d b e Selection Guide (partial) Part No. Case Size Output
More informationTPM Fuse Panel Installation Guide. Document INS-727XXXXXXX This manual covers the following part numbers- Trimm 727XXXXXXX Family
TPM Fuse Panel Installation Guide Document INS-727XXXXXXX This manual covers the following part numbers- Trimm 727XXXXXXX Family Table of Contents Section 1- General Information... 3 1.1 - Product Description...
More information2.0 CONSTRUCTION 3.0 OPERATION. SA-1 Generator Differential Relay - Class 1E 2.5 TRIP CIRCUIT
41-348.11C SA-1 Generator Differential Relay - Class 1E 2.0 CONSTRUCTION The type SA-1 relay consists of: Restraint Circuit Sensing Circuit Trip Circuit Surge Protection Circuit Operating Circuit Amplifier
More informationATD WATT INVERTER
ATD-5954 1500 WATT INVERTER Welcome. This ATD product has been carefully engineered and manufactured to give you dependable operation. Please read this manual thoroughly before operating your new ATD product,
More informationA Caspian Technology Company all materials presented are trade mark and copyright protected by C.M.TECHNOLOGY Pty Ltd
PPS12 230v AC to 12 VDC POWER SUPPLY WITH BATTERY MANAGER OPTION 2 Table of Contents Introduction:... 3 1.0: Input Voltage:... 4 1.1: Mains Hold Up (missing mains cycles):... 4 1.2: Mains Input:... 4 1.3:
More informationTPM/GMT Panel Installation Guide
TPM/GMT Panel Installation Guide Document INS-837xxxxxxx This manual covers the following part numbers- Trimm 837xxxxxxx Family Table of Contents Table of Contents... 2 Section 1- General Information...
More informationGeneral safety and installation information.
Read these instructions before connecting and using your PowerBright Pure Sine Power Inverters. Failure in observing this warning may result in injury to persons and damage to equipment. General safety
More informationXP800i POWER INVERTER OWNER S MANUAL
XP800i POWER INVERTER OWNER S MANUAL INTRODUCTION Dear Whistler Customer, For many of us, a vehicle is more than just transportation. It can be a mobile office, communications or entertainment center,
More informationXENON POWER SUPPLY 4000 Watt Gladiator IV
XENON POWER SUPPLY 4000 Watt Gladiator IV 220 Volt Equipment Type 62-00049 Rev. February 2003 STRONG INTERNATIONAL a division of Ballantyne of Omaha, Inc. 4350 McKinley Street Omaha, Nebraska 68112 USA
More informationPOWER AMPLIFIER SERVICE MANUAL CONTENTS
POWER AMPLIFIER CONTENTS Performance Specifications... 2 Notes... 2 Rear Panel... 3 Section Location... 3 Block Diagram... 4 Interconnection Diagram... 5-8 Multi-channel Schematic and PCB... 9 Heatsink
More information5001TCP SPEED CONTROLLER
VARIABLE SPEED DRIVE CONTROLLER INSTALLATION AND SETTING UP MANUAL 5001TCP SPEED CONTROLLER With PC101 Torque Limit Control WARNING Disconnect all incoming power before working on this equipment. Follow
More informationMATRIX FILTER USER MANUAL. SERIES D 600 Volts, 60HZ PART NO. INSTR 026 REL MTE Corporation
MATRIX FILTER SERIES D 600 Volts, 60HZ USER MANUAL PART NO. INSTR 026 REL. 080920 2008 MTE Corporation IMPORTANT USER INFORMATION NOTICE The MTE Corporation Matrix Filter is designed for harmonic mitigation
More informationPure Sine Wave Power Inverter SSW A SSW A SSW A SSW A SSW A
Pure Sine Wave Power Inverter SSW-350-12A SSW-600-12A SSW-1000-12A SSW-1500-12A SSW-2000-12A Owner's Manual Please read this manual before installing your inverter 1 IMPORTANT SAFETY INSTRUCTIONS THIS
More informationDP140e. Installation & Operations Manual
Installation & Operations Manual DP140e System Engineering International SEI Incorporated 5115 Pegasus Court, Suite Q Frederick, MD 21704 Phone 301-694-9601 / 800-765-4SEI Fax 301-694-9608 Web http//www.seipower.com
More informationUninterruptible Power Systems
Sola 4K Industrial On-Line Uninterruptible Power Systems (UPS) The true on-line (double conversion) protection offered by the S4K Industrial UPS series eliminates a wider range of potential power problems
More informationM T E C o r p o r a t i o n MATRIX FILTER. SERIES B Volts, 50HZ USER MANUAL PART NO. INSTR REL MTE Corporation
M T E C o r p o r a t i o n MATRIX FILTER SERIES B 380-415 Volts, 50HZ USER MANUAL PART NO. INSTR - 015 REL. 060628 2006 MTE Corporation IMPORTANT USER INFORMATION NOTICE The MTE Corporation Matrix Filter
More informationM T E C o r p o r a t i o n. dv/dt Filter. Series A VAC USER MANUAL PART NO. INSTR REL MTE Corporation
M T E C o r p o r a t i o n dv/dt Filter Series A 440-600 VAC USER MANUAL PART NO. INSTR - 019 REL. 041119 2004 MTE Corporation IMPORTANT USER INFORMATION NOTICE The MTE Corporation dv/dt Filter is designed
More informationMatrix AP 400V 690V INSTALLATION GUIDE. Quick Reference. ❶ How to Install Pages 6 20 ❷ Startup/Troubleshooting Pages WARNING
Matrix AP 400V 690V INSTALLATION GUIDE FORM: MAP-IG-E REL. May 2017 REV. 002 2017 MTE Corporation WARNING High Voltage! Only a qualified electrician can carry out the electrical installation of this filter.
More information3. OPERATION 2.1. RESTRAINT CIRCUIT 2.6. INDICATING CIRCUIT 2.2. OPERATING CIRCUIT 2.7. SURGE PROTECTION CIRCUIT 2.3.
41-348.1H Type SA-1 2.1. RESTRAINT CIRCUIT The restraint circuit of each phase consists of a center-tapped transformer, a resistor, and a full wave rectifier bridge. The outputs of all the rectifiers are
More informationEclipse Plus VA UPS and Surge Suppressor User s Manual
Eclipse Plus 250 250VA UPS and Surge Suppressor User s Manual Compact UPS/Surge Suppressor for Home Office or Small Office Use www.mgeups.com Notes Contents Thank You!.....................................................
More informationParts Manual. Transfer Switch. OTPCB (Spec A) 150/225/260 Amps. English Original Instructions (Issue 4)
Parts Manual Transfer Switch 50/225/260 Amps OTPCB (Spec A) English Original Instructions -203 962 0228 (Issue ) This catalog covers models produced under the Cummins /Onan and Cummins Power Generation
More information55 Series - Miniature General Purpose Relays 5-10 A
Series - Miniature General Purpose Relays -0 A - Plug-in or P.C.B. versions - AC or DC coils - Lockable test button and mechanical flag indicator as standard on and CO relays types - Sockets and accessories:
More informationENGINE GOVERNING SYSTEMS LSM672 LOAD SHARING MODULE. GOVERNORS AMERICA CORP. 720 Silver Street Agawam, MA , USA MEMBER
ENGINE GOVERNING SYSTEMS LSM672 LOAD SHARING MODULE MEMBER GOVERNORS AMERICA CORP. 720 Silver Street Agawam, MA 01001-2907, USA LSM672 LOAD SHARING MODULE PRODUCT TECHNICAL INFORMATION PTI 4000 AUGUST
More informationACSI MODEL 1440 POWER SUPPLY INSTALLATION INSTRUCTIONS
II 1400-8 Features: ACSI MODEL 1440 POWER SUPPLY INSTALLATION INSTRUCTIONS Filtered/Regulated 24 Volts DC Up to Full 2 Amps Load Capacity Class 2 Rated Outputs Overload, Over Voltage, and Short Circuit
More informationParts Manual. Transfer Switch. OTPCC (Spec A) 300/400/600 Amps. English Original Instructions (Issue 4)
Parts Manual Transfer Switch 00/00/600 Amps OTPCC (Spec A) English Original Instructions -20 962 0229 (Issue ) This catalog covers models produced under the Cummins /Onan and Cummins Power Generation brand
More informationIQS300 Series Quasi-Sine Inverter. Installation & Operation Manual
IQS300 Series Quasi-Sine Inverter Installation & Operation Manual INTRODUCTION State of the Art MOSFET technology coupled with unique Soft-Start circuitry guarantees reliable operation. The ON-OFF switch
More informationAT10.1 SERIES FLOAT BATTERY CHARGERS. Advanced technology microprocessor control
Motive Power Systems Reserve Power Systems Special Power Systems Service AT10.1 SERIES LOAT BATTERY CHARGERS UL-1564 CSA-C22.2 Seismic Zone 4 Qualification Advanced technology microprocessor control Constant
More informationdv Sentry TM 208V 600V INSTALLATION GUIDE Quick Reference ❶ How to Install Pages 6 14 ❷ Startup/Troubleshooting Pages WARNING
dv Sentry TM 208V 600V INSTALLATION GUIDE FORM: DVS-IG-E REL. January 2018 REV. 003 2018 MTE Corporation High Voltage! Only a qualified electrician can carry out the electrical installation of this filter.
More informationTECH XP250 INSTALLATION AND OPERATION MANUAL. Manufacturer of UL Listed Products.
http://wwwwholesalesolarcom/invertershtml TECH 7317 Jack Newell Blvd North Fort Worth, Texas 76118-7100 8175954969 voice, 8175951290 fax 8008864683 toll free website wwwexeltechcom R Manufacturer of UL
More informationData Bulletin. Ground-Censor Ground-Fault Protection System Type GC Class 931
Data Bulletin 0931DB0101 July 2001 Cedar Rapids, IA, USA Ground-Censor Ground-Fault Protection System Type GC Class 931 09313063 GT Sensor Shunt Trip of Circuit Interrupter Window Area for Conductors GC
More informationCBC-300 Series & CBC-300C Series Dual Channel Adjust Clutch/Brake Controls
CBC-300 Series & CBC-300C Series Dual Channel Adjust Clutch/Brake Controls P-269-89-0408 Installation Installation & Operating Instructions Contents Introduction........................... 2 Specifications.........................
More informationHigh Frequency SineWave Guardian TM
High Frequency SineWave Guardian TM 380V 480V INSTALLATION GUIDE FORM: SHF-IG-E REL. January 2018 REV. 002 2018 MTE Corporation High Voltage! Only a qualified electrician can carry out the electrical installation
More informationPCB Relay. Contact form Terminals Coil terminals Rated voltage Model SPST-NO #250 tab terminals PCB terminals 5, 12, 24 VDC G4A-1A
PCB Relay Miniature Single-pole Relay with 80-A Surge Current and 20-A Switching Current Ideal for motor switching. Miniature, relay with high switching capacity built-in applications. Creepage distance
More informationCONTROL FEATURES AVAILABLE OPTIONS
Vari Speed A2000 TABLE OF CONTENTS Control Features Options Application Data Operating Condition s Control Ratings Chart Mounting Dimensions Installation and Wiring Typical Wiring Diagram Schematic (Block
More informationThe Power of Reliability INSTRUCTION MANUAL
The Power of Reliability INSTRUCTION MANUAL SAFETY & WARNINGS Read this manual carefully and understand all Warnings and Cautions before connections are made to the Inverter. If unsure about any aspects
More informationATD WATT INVERTER
ATD-5955 2000 WATT INVERTER Welcome. This ATD product has been carefully engineered and manufactured to give you dependable operation. Please read this manual thoroughly before operating your new ATD product,
More informationXP600/1100/2000 INSTALLATION AND OPERATION MANUAL
7317 Jack Newell Blvd North Fort Worth, Texas 76118-71 817-595-4969 voice, 817-595-129 fax 8-886-4683 toll free website wwwexeltechcom Manufacturer of UL Listed Products Copyright 21 Exeltech Inc All rights
More informationBattery Control Center - Diesel
Service Manual CAUTION: All servicing of the Battery Control Center should be done only by a qualified Service Technician. Inadvertent shorts inside the Battery Control Center could result in severe damage
More information5001TCP SPEED CONTROLLER
INSTALLATION AND SETTING UP MANUAL 5001TCP SPEED CONTROLLER WARNING Disconnect all incoming power before working on this equipment. Follow power lockout procedures. Use extreme caution around electrical
More informationKinetics Industries, Inc. 140 Stokes Ave. Trenton, NJ 08638 Tel: 609-883-9700 sales ext 122, Fax: 609-883-0025 e-mail: info@kinetics-industries.com www.kinetics-industries.com Kinetics manufacturer of:
More informationA system fault contribution of 750 mva shall be used when determining the required interrupting rating for unit substation equipment.
General Unit substations shall be 500 kva minimum, 1500 kva maximum unless approved otherwise by the University. For the required configuration of University substations see Standard Electrical Detail
More informationDNH INDUSTRIES ***** COMPACT ***** EASY TO INSTALL ***** STATUS INDICATORS ***** DUAL LINE FUSING ***** INSULATED FRONT COVER ***** ADJUSTABLE OUTPUT
DNH INDUSTRIES ***** COMPACT 24100 FRAMPTON AVE., BLDG B, HARBOR CITY, CALIFORNIA 90710 TEL: 310.517.1769 FAX: 310.517.0875 E'MAIL: dnhind@aol.com WEB: dnhindustries.com DIGI-FIRE SOLID STATE MOTOR WINDING
More information3 Uninterruptible Power Systems
S4K2U and S4K2U-5 Industrial On-Line UPS The true on-line (double conversion) protection offered by the S4K2U Industrial UPS series eliminates a wider range of potential power problems (spikes, surges
More information2. AC SERVICE AND MOTOR REQUIRED 1. ENCLOSURE REQUIRED
1. ENCLOSURE REQUIRED If the OC1 control is furnished as an open-chassis unit (standard), mount control in an enclosure 12 x 10 x 5 or larger and mount enclosure where room temperature does not exceed
More informationMedium Voltage Standby non-paralleling Control GUIDE FORM SPECIFICATION
Medium Voltage Standby non-paralleling Control 1. GENERAL GUIDE FORM SPECIFICATION A. The requirements of the contract, Division 1, and part 16 apply to work in this section. 1.01 SECTIONS INCLUDE A. Medium
More informationM T E C o r p o r a t i o n MATRIX FILTER. SERIES B Volts, 50HZ USER MANUAL PART NO. INSTR REL MTE Corporation
M T E C o r p o r a t i o n MATRIX FILTER SERIES B 380-415 Volts, 50HZ USER MANUAL PART NO. INSTR - 015 REL. 040709 2003 MTE Corporation IMPORTANT USER INFORMATION NOTICE The MTE Corporation Matrix Filter
More informationSAFETY WARNINGS AND GUIDELINES
SAFETY WARNINGS AND GUIDELINES Place the inverter in a well-ventilated environment. Ensure that the cooling fan is not blocked and that it operates as intended. Do not use the inverter if the fan fails
More informationFilm-Tech. The information contained in this Adobe Acrobat pdf file is provided at your own risk and good judgment.
Film-Tech The information contained in this Adobe Acrobat pdf file is provided at your own risk and good judgment. These manuals are designed to facilitate the exchange of information related to cinema
More information1/4HP - 7.5HP 120/240/277 VOLTS 50/60HZ
Installation & Operating Procedures DG2 Series SINGLE PHASE CONVERTERS 1/4HP - 7.5HP 120/240/277 VOLTS 50/60HZ TABLE OF CONTENTS 1.0 DESCRIPTION... Pg. 1 2.0 INSTALLATION AND START-UP... Pg. 3 3.0 DRAWING
More informationACA-20PC Series Digital, LED-Display AC Ammeters with Built-in Current Transformers
www.murata-ps.com Now Available with Wire Lead CTs FEATURES for direct measurement of 0 to 2/20/50/100 Amps Functionally complete: On-board current transformers Scaling/interface circuitry Precision A/D
More informationVLT SERIES. True Sine Wave AC Power Inverter. Owner s Manual. Owner s Manual D Rev.B
Owner s Manual VLT SERIES True Sine Wave AC Power Inverter 60Hz Models VLT12-600 VLT12-1000 VLT12-1500 VLT24-600 VLT24-1000 VLT24-1500 VLT48-1000 VLT48-1500 50Hz Models VLTE12-600 VLTE12-1000 VLTE12-1500
More informationESD5500E Series Speed Control Unit
ESD5500E Series Speed Control Unit 1 SPECIFICATIONS INTRODUCTION PERFORMANCE Isochronous Operation ± 0.25% or better Speed Range / Governor 1-7.5 KHz Continuous Speed Drift with Temperature ±1% Maximum
More informationTECH XP600/1100 INSTALLATION AND OPERATION MANUAL. Manufacturer of UL Listed Products.
http://wwwwholesalesolarcom/invertershtml TECH 7317 Jack Newell Blvd North Fort Worth, Texas 76118-71 8175954969 voice, 817595129 fax 88864683 toll free website wwwexeltechcom R Manufacturer of UL Listed
More informationEuclid Full Voltage Magnet Controller
Hubbell Industrial Controls, Inc. Euclid Full Voltage Magnet Controller Instruction & Renewal Parts Manual Instructions/Parts Manual Publication No. 180 Replaces Sept. 1991 4291 & 4295/ 96 Type 4291 Type
More informationXENON POWER SUPPLY Watt
XENON POWER SUPPLY 3000-5000 Watt 220 Volt Equipment Type 62-00016 62-00017 62-00004 (Export) Rev. February 2006 STRONG INTERNATIONAL a division of Ballantyne of Omaha, Inc. 4350 McKinley Street Omaha,
More informationOWNERS MANUAL JANUARY 2007 ISO
Manufacturer of Dimensions TM Inverters 4467 White Bear Parkway St. Paul, MN 55110 Phone: 651-653-7000 Fax: 651-653-7600 E-mail: inverterinfo@sensata.com Web: www.dimensions.sensata.com 121231B OWNERS
More informationADI-125/750 ADI-125/1500 ADI-125/2500
Manufacturer of Dimensions TM Inverters 4467 White Bear Parkway St. Paul, MN 55110 Phone: 651-653-7000 Fax: 651-653-7600 E-mail: inverterinfo@sensata.com Web: www.dimensions.sensata.com 121094B OWNERS
More informationUser Manual. NetGuard IMPORTANT. PSD 650/1200/1600 Line Interactive UPS Uninterruptible Power Supply System. UPS Monitoring Software
User Manual Thank you for purchasing the Defender 650/1200/1600. It is designed to provide safe and reliable power protection to your precious electronics equipment. Before you start using the product,
More informationCONTENTS 1. INTRODUCTION SAFTY INSTRUCTION CABLE CONNECTION SYSTEM DESCRIPTION OPERATION... 9
USER MANUAL 1 CONTENTS 1. INTRODUCTION... 1 2. SAFTY INSTRUCTION... 3 3. CABLE CONNECTION... 4 4. SYSTEM DESCRIPTION... 5 5. OPERATION... 9 6. TROUBLE SHOOTING GUIDE... 25 7. OPERATION MODES..... 27 8.
More informationUser Manual 4KVA/ 5KVA INVERTER / CHARGER. With MPPT Controller
User Manual 4KVA/ 5KVA INVERTER / CHARGER With MPPT Controller CONTENTS ABOUT THIS MANUAL... 1 Purpose... 1 Scope... 1 SAFETY INSTRUCTIONS... 1 INTRODUCTION... 2 Features... 2 Basic System Architecture...
More informationKinetics Industries Inc. 140 Stokes Ave. Trenton, NJ Fax
Kinetics Industries Inc. 140 Stokes Ave. Trenton, NJ 08638 609-883-9700 609-883-0025 Fax Common optional features include: AC main line contactor, DC undervoltage and / or undercurrent relay, regenerative
More informationUser Manual 1KVA/ 2KVA/ 3KVA INVERTER / CHARGER
User Manual 1KVA/ 2KVA/ 3KVA INVERTER / CHARGER CONTENTS ABOUT THIS MANUAL... 1 Purpose... 1 Scope... 1 SAFETY INSTRUCTIONS... 1 INTRODUCTION... 2 Features... 2 Basic System Architecture... 2 Product Overview...
More informationCONTENTS 1. INTRODUCTION SAFTY INSTRUCTION CABLE CONNECTION SYSTEM DESCRIPTION INVERTER OPERATION...
CONTENTS 1. INTRODUCTION...... 1 2. SAFTY INSTRUCTION.......... 2 3. CABLE CONNECTION.......... 4 4. SYSTEM DESCRIPTION............ 5 5. INVERTER OPERATION... 11 6. TROUBLE SHOOTING GUIDE....... 16 7.
More informationSolar Hybrid Inverter SP Efecto Series
User Manual Solar Hybrid Inverter SP Efecto Series Version 1.2 Table Of Contents ABOUT THIS MANUAL... 1 Purpose... 1 Scope... 1 SAFETY INSTRUCTIONS... 1 INTRODUCTION... 2 Features... 2 Basic System Architecture...
More informationPowermite 599 MT Series SQS Electronic Valve Actuator, 24 Vac, Floating Control (3-position)
Powermite 599 MT Series SQS Electronic Valve Actuator, 24 Vac, Floating Control (3-position) Document No. 155-308P25 EA 599-14 Description Features Application The Powermite 599 MT Series SQS85.53U Electronic
More informationTECH XP600/1100 INSTALLATION AND OPERATION MANUAL
TECH 7317 Jack Newell Blvd North Fort Worth, Texas 76118-71 8175954969 voice, 817595129 fax 88864683 toll free e-mail address info@exeltechcom e-mail address sales@exeltechcom website wwwexeltechcom Copyright
More informationSeries 5 Inverter OPEN CHASSIS MOUNT - SINGLE PHASE INPUT. For Catalog Nos. ID56F50-CO, ID5601-CO & ID5602-CO
Series 5 Inverter OPEN CHASSIS MOUNT - SINGLE PHASE INPUT For Catalog Nos. ID56F50-CO, ID5601-CO & ID5602-CO 1/17 Installation & Operating Manual MN781 Table of Contents Chapter 1 Introduction Introduction...
More informationMODEL 8002SW (1996 MSRP $ )
F O R T H E L O V E O F M U S I C MODEL 8002SW (1996 MSRP $1549.00) INSTALLATION AND OPERATION MANUAL INTRODUCTION Congratulations, with all the auto sound equipment available on the market today, decisions
More information********SERVICE MANUAL********* MODELS:
********SERVICE MANUAL********* MODELS: -------------- 7553-70 Variable Speed Drive/Controller System, 600 rpm, 115v 7553-71 Variable Speed Controller only, 600 rpm,115v 7553-80 Variable Speed Drive/Controller
More informationSineWave Guardian TM 380V 600V INSTALLATION GUIDE. Quick Reference. ❶ How to Install Pages 6 17 ❷ Startup/Troubleshooting Pages WARNING
SineWave Guardian TM 380V 600V INSTALLATION GUIDE FORM: SWG-IG-E REL. October 2018 REV. 003 2018 MTE Corporation High Voltage! Only a qualified electrician can carry out the electrical installation of
More informationInstallation Sheet January, 2016 Supersedes February, 2013
s Installation Sheet January, 016 Supersedes February, 013 E87010-A0104-T003-A6-CLM0 Lighting and Heating Contactor 30 Amp, 3, 4, 5 Pole Magnetically Latched Description Magnetically latched CLM lighting
More information