Thermistor Temperature Sensor Range

Transcription

1 smart Main Features ontrols Temperature Sensors for all common applications Data Sheet S1 Temperature Sensors with Thermistor Elements Close tolerance Thermistor Elements (+/- 0.2 accuracy within range of 0 to 70 ) Thermistor Temperature Sensor Range Immersion Temperature Clamp-On Temperature Outside Air Temperature Duct Temperature Pocket Accessories Room Temperature Room Temperature with Setpoint Adjustment Room Temperature with Setpoint Adjustment and Fan Speed Switch Room Temperature with Setpoint Adjustment and Occupancy Override Switch Black Bulb Temperature Bead Sensor Thimble Sensor smartkontrols Data Sheet S1 Part No LIT / DAT / SEN / 001 Iss 1 Jan 2002 Page1 1 of 8

2 S1 SEN / PR / IMM / 001 Plant Room Sensors Immersion Temperature Sensor IP65 rated Measures the temperature of liquids in pipework and vessels. Direct mounting into a brass or stainless steel pocket (separately available as an accessory). Dimensions: 57mm x 90mm diameter IP rated 67 Ambient: -10 to 60 Connection: 2 way terminal block, Houses sensor Dimensions: 150mm x 6mm diameter Material: Brass If the sensor is to be mounted outside, it is recommended that the unit be mounted with the cable entry at the bottom. In addition, if the cable is fed from above the sensor we also recommend that a rain loop is placed in the cable before entry into the sensor. Remove the front cover by twisting the lid and separating from the main body to make the electrical connections. Fix the sensor in to the pocket and secure with the grub screw provided with the pocket. Feed the cable through the waterproof gland and terminate the cores at the terminal block. Leave some slack inside the unit, tighten the cable gland onto the cable to ensure watertightness. Replace the lid after the electrical connections have been made. SEN / PR / CLP / 001 Measures pipe surface temperature. Includes steel band strap for clamping onto pipes (may require longer strap for larger vessels). Clamp-On Temperature Sensor IP65 Dimensions: 57mm x 90mm diameter IP rated 67 Ambient: -10 to 60 Connection: 2 way terminal block, Houses sensor Material: Brass Cable: 1.5m of PTFE 2 core screened cable If the sensor is to be mounted outside, it is recommended that the unit be mounted with the two cable entries at the sides. In addition, if the cables are fed from above the IP65 housing we also recommend that a rain loop is placed in the cable before entry into the sensor. Remove the front cover by twisting the lid and separating from the main body. Using the base of the housing as a template mark the hole centres. Drill two pilot holes at 85mm centres in the surface on which the sensor is to be mounted, and fix the sensor with appropriate screws. The housing is designed to make it easy for an electric screwdriver to be used if desired. Feed the cables through the waterproof glands and terminate the cores at the terminal blocks. Leaving some slack inside the units, tighten the cable glands onto the cables to ensure watertightness. Replace the lid after the electrical connections have been made. smartkontrols Data Sheet S1 Part No LIT / DAT / SEN / 001 Iss 1 Jan 2002 Page1 2 of 8

3 Plant Room Sensors S1 SEN / PR / OAT / 001 Measures outside air temperature. Sensing is contained within 10mm diameter brass cap, located externally in the shadow of the lid to avoid solar gain in most applications. Outside Air Temperature Sensor IP65 Dimensions: 57mm x 90mm diameter IP rated 67 Ambient: -10 to 60 10mm diameter brass cap houses sensor Connection: 2 way terminal block, Cable: 1.5m of PTFE 2 core screened cable Outside air sensors should always be situated in a sheltered position on a north facing wall. Avoid mounting the sensor in direct sunlight. It is recommended that the unit be mounted with the cable entry at the bottom. In addition, if the cable is fed from above the sensor we also recommend that a rain loop is placed in the cable before entry into the sensor. Remove the front cover by twisting the lid and separating from the main body. Using the base of the housing as a template mark the hole centres. Drill two pilot holes at 85mm centres in the surface on which the sensor is to be mounted, and fix the sensor with appropriate screws. The housing is designed to make it easy for an electric screwdriver to be used if desired. Feed the cable through the waterproof gland and terminate the cores at the terminal block. Leaving some slack inside the units, tighten the cable gland onto the cable to ensure watertightness. Replace the lid after the electrical connections have been made. SEN / PR / DCT / 001 Duct Temperature Sensor Measures air temperature in ducts. Sensing is contained within 150mm long brass probe with holes to allow air to flow directly over the. A neoprene gasket is supplied to ensure a good seal onto the duct. Dimensions: 57mm x 90mm diameter IP rated 67 Ambient: -10 to 80 Connection: 2 way terminal block, Houses sensor Dimensions: 150mm x 6mm diameter Material: Brass If the sensor enclosure is to be mounted outside, it is recommended that the unit be mounted with the cable entry at the bottom. In addition, if the cable is fed from above the sensor we also recommend that a rain loop is placed in the cable before entry into the sensor. Remove the front cover by twisting the lid and separating from the main body. Using the base of the housing as a template mark the hole centres. Drill two pilot holes at 85mm centres in the surface on which the sensor is to be mounted. Apply the gasket provided to the base of the housing. Align the holes in the probe so that they point into the airflow, not at right-angles to it. Press onto the side of the ductwork to form a seal between the sensor and the duct. Fix the sensor with appropriate screws. The housing is designed to make it easy for an electric screwdriver to be used if desired. Feed the cable through the waterproof gland and terminate the cores at the terminal block. Leaving some slack inside the units, tighten the cable gland onto the cable to ensure watertightness. Replace the lid after the electrical connections have been made. smartkontrols Data Sheet S1 Part No LIT / DAT / SEN / 001 Iss 1 Jan 2002 Page1 3 of 8

4 S1 SEN / BP and SEN / SS Accessories Pocket for Immersion Temperature Sensor SEN / BP Brass Pocket for Immersion Temperature Sensor SEN / SS Stainless Steel Pocket for Immersion Temperature Sensor Pockets are designed to accept 150mm x 6mm diameter probes, which are locked in position by a grub screw. Brass Pocket Material: Brass Range: -20 to 110 Max Pressure: 10 bar (out to in) Stainless Steel Pocket Material: Stainless Steel 316 Range: -20 to 400 Max Pressure: 16bar (out to in) Pattress Mount Sensors Pockets can be installed in any system that is constructed from compatible materials whose operating pressures are within the specified ranges and fit into a 1/2" BSPT boss using a thread-seal compound. In pipework systems, fit into an elbow such that the pocket runs down the centre of the pipe, against the direction of flow SEN / PTR / ROM / 001 Room Temperature Sensor Dimensions: 83mm x 83mm x 27mm. Ambient Range -10 to 60 Connections are made via a terminal block, polarity independant. Measures air temperature in indoor spaces. Sensing is mounted in a white moulded enclosure for surface mounting on a wall or SEN / PTR / ROM / 002 Room Temperature Sensor with Setpoint Adjust As standard room sensor Setpoint Adjustment: 1 to 11k ohm pot Connections TB1: Terminals 3 and 4: Setpoint resistance TB1: Terminals 5 and 6: Temperature sensor Room Temperature Sensor with Setpoint Adjustment Potentiometer smartkontrols Data Sheet S1 Part No LIT / DAT / SEN / 001 Iss 1 Jan 2002 Page1 4 of 8

5 Pattress Mount Sensors S1 SEN / PTR / ROM / 003 Room Temperature Sensor with Setpoint Adjust and Fan Switch As standard room sensor Setpoint Adjustment: 1 to 11k ohm pot Fanspeed Adjustment: 5 position slide switch setting resistance Connections TB1: Terminals 1 and 2: Fan Speed resistance TB1: Terminals 3 and 4: Setpoint resistance TB1: Terminals 5 and 6: Temperature sensor SEN / PTR / ROM / 003 Room Temperature Sensor with Setpoint Adjust and Fanspeed Adjust Switch SEN / PTR / ROM / 004 SEN / PTR / ROM / 004 Room Temperature Sensor with Setpoint Adjust and Occupation Switch SEN / PTR / BLK / 001 Room Temperature Sensor with Setpoint Adjust and Override Switch As standard room sensor Setpoint Adjustment: 1 to 11k ohm pot Occupation Switch: Rocker switch for on/off operation NB Option switches MUST NOT be used to switch 230Vac Indoor Black Bulb Sensor Connections TB1: Terminals 3 and 4: Setpoint resistance TB1: Terminals 5 and 6: Temperature sensor TB2: Terminal 14: Occupation switch NO TB2: Terminal 15: Occupation switch Common TB2: Terminal 16: Occupation switch NC Dimensions: 83mm x 83mm x 27mm. Ambient Range -10 to 60 Connections are made via a terminal block, polarity independant. Black Bulb Sensor Measures black bulb air temperature in indoor spaces. Sensing is mounted in a white moulded enclosure for surface mounting on a wall or smartkontrols Data Sheet S1 Part No LIT / DAT / SEN / 001 Iss 1 Jan 2002 Page1 5 of 8

6 S1 SEN / FL / [option] / 001 Flying Lead Sensors Bead Sensor Houses sensor Dimensions: 35mm x 6mm diameter Material: 316 Stainless Steel Connection: 2 core flying lead 1m or 3m, Ambient -40 to 60 SEN / FL / 1M / 001 Bead Temperature Sensor with 1M Flying Lead SEN / FL / 3M / 001 Bead Temperature Sensor with 3M Flying Lead Measures air temperature, especially in fan coil units etc. SEN / THM / [option] SEN / THM / P Thimble Temperature Sensor with White Plastic Finish SEN / THM / BR Thimble Temperature Sensor with Brass Finish SEN / THM / ALP Thimble Temperature Sensor with Polished Aluminium Finish SEN / THM / ALB Thimble Temperature Sensor with Brushed Aluminium Finish SEN / THM / SS Thimble Temperature Sensor with Stainless Steel Finish Measures air temperature in indoor spaces. Thimble Sensor Houses sensor Drill a suitable hole in the mounting surface. Pass the flying lead and threaded part of the body through the Dimensions: 45mm x hole. Secure with the fixing nut provided. 22mm diameter Thread: M16 x 1.5mm x 25mm (internal 11mm x 20mm) Material (/P): Flame Material (/BR): Brass Material (/ALP): Polished Aliminium Material (/ALB): Brushed Aluminium Material (/SS): 316 Stainless Steel Connection: 2 core flying lead 1m, Ambient -10 to 60 smartkontrols Data Sheet S1 Part No LIT / DAT / SEN / 001 Iss 1 Jan 2002 Page1 6 of 8

7 Sensor Installation S1 Wiring Guidelines Sensor cabling should be to the same specification as per the SeaChange Network - Unscreened, Twisted pair Belden Use twisted pair, unscreened cable for all sensor wiring (and input wiring - e.g. from contactor auxiliaries, flow switches etc). Use this cable for the entire run from the SeaChange input terminals to the sensor. Recommended maximum cable length 100m. Do not use single conductors, even for short runs in the panel; an electrical panel is often a noisy electrical environment. If already installed, Screened twisted pair cables can sometimes be re-used for sensors without detriment provided the screen is continuous and properly earthed at one point only. Do not use screened cables on new installations. New installations should always use the correct Unscreened, Twisted pair cable. Sensors should be of the insulated type and not earthed. There is no particular requirement to segregate from Mains wiring, but prudent installers will always avoid long, parallel runs. Inputs All inputs to SeaChange modules are Non-Isolated; this means that you must not connect inputs from different controllers together, or connect inputs to 0V or earth, or any other potential. Sensor Resistance Tables (+/- 0.2 accuracy within range of 0 to 70 ) Resistance Tables Ohms Ohms Ohms Ohms smartkontrols Data Sheet S1 Part No LIT / DAT / SEN / 001 Iss 1 Jan 2002 Page1 7 of 8

8 S1 Options and Product s Specification Thermistor Sensors Plant Room Sensors SEN / PR / IMM / 001 SEN / PR / CLP / 001 SEN / PR / OAT / 001 SEN / PR / DCT / 001 Accessories SEN / BP SEN / SS Pattress Mount Sensors SEN / PTR / ROM / 001 SEN / PTR / ROM / 002 SEN / PTR / ROM / 003 SEN / PTR / ROM / 004 SEN / PTR / BLK / 001 Bead Sensors SEN / FL / 1M / 001 SEN / FL / 3M / 001 Thimble Sensors SEN / THM / P SEN / THM / BR SEN / THM / ALP SEN / THM / ALB SEN / THM / SS Immersion Temperature Sensor IP65 Clamp-On Temperature Sensor IP65 Outside Air Temperature Sensor IP65 Duct Temperature Sensor Brass Pocket for Immersion Temperature Sensor Stainless Steel Pocket for Immersion Temperature Sensor Room Temperature Sensor Room Temperature Sensor with Setpoint Adjust Room Temperature Sensor with Setpoint Adjust and Fanspeed Adjust Switch Room Temperature Sensor with Setpoint Adjust and Occupation Switch Black Bulb Sensor Bead Temperature Sensor with 1M Flying Lead Bead Temperature Sensor with 3M Flying Lead Thimble Temperature Sensor with White Plastic Finish Thimble Temperature Sensor with Brass Finish Thimble Temperature Sensor with Polished Aluminium Finish Thimble Temperature Sensor with Brushed Aluminium Finish Thimble Temperature Sensor with Stainless Steel Finish smart ontrols 8 Horsted Square Bell Lane Business Park Uckfield East Sussex TN22 1QG phone fax sales@smartkontrols.co.uk smartkontrols Data Sheet S1 Part No LIT / DAT / SEN / 001 Iss 1 Jan 2002 Page1 8 of 8