USA CANADA.

Transcription

1

2 CANADA Motion Concepts 84 Citation Dr., Unit 1-7 Concord, ON L4K 3C1 Toll Free Tel: Tel: Fax: USA Motion Concepts 700 Ensminger Rd., Suite 112 Tonawanda, NY Toll Free Tel: Toll Free Fax:

3 PRODUCT REFERENCE: Our modular UltraLow CG system is designed to provide dealers and therapists with the ultimate in versatility, flexibility and adjustability. The modular system can be readily adapted from base to base. Modules can be added and subtracted with minimal time and effort.* LOW SEAT-TO-FLOOR HEIGHT (STF) Whether it s at a desk or behind the steering wheel, lower seat-to-floor heights can significantly improve accessibility for people in wheelchairs. Seat-to-floor (STF) is measured from the floor to the front edge of the seat pan. STF is dependent on the characteristics of the power base. TILT The tilt function enables wheelchair users to infinitely change their position by tilting a fixed seat frame around an axis of rotation of up to 55. Most modules are available with a tilt system. RECLINE The recline function enables users to infinitely change the seat to back angle of their system within a set range. An open hip angle distributes weight more evenly and can reduce pressure while increasing comfort. Most recline systems extend up to 174. HPMSR HPMSR (high pivot mechanical shear reduction) is synchronized with recline to effectively reduce shear through optimal, physiological positioning of recline pivot points. This mounting geometry eliminates the need to slide the backrest on the backposts as the back reclines. ESR ESR (extended shear reduction) is synchronized with recline to reduce the amount of shear between the client and the backrest. This is accomplished using a linkage that slides the backrest on the backposts as the back reclines. PSB PSB (power sliding back) allows the back pan to be adjusted vertically (up and down) as a separate seating function, independent of recline and/or in synchronization with recline. This feature is effective for individuals that sit for extended periods of time as it allows for simple repositioning of the back and head. PRECLINE An option available with recline systems, precline adjusts the back angle of the seating system into a forward position, closing seat to back angle to less then 90. This can assist in transfers and other functional tasks, while also working to accommodate certain types of skeletal deformities. ELEVATE The elevate module allows users to raise their entire power positioning system 5", 6", 7" or 8" (dependent on weight capacities) above the lowest seat-to-floor height of their system. ULTRALIFT The ultralift module allows users to raise their entire power positioning system 10" above the lowest seat-to-floor height of their system. ANTERIOR ASSIST Anterior assist is available on our tilt and tilt/recline UltraLow CG system and offers limited anterior (forward) tilt about a fixed axis. The rear position of the seat remains constant while the front lowers This system design provides effective pressure reduction and transfer assistance. ANTERIOR TILT A separate power module designed to allow up to 30 of anterior tilt, while maintaining full posterior tilt capabilities. The rear of the entire system (ie: tilt or tilt/recline) is raised. This module is intended for use with our UltraLow system, and is particularly effective with our elevating module to aid in day-to-day activities including self or assisted standing transfers and visual field orientation. *Available modules and modular combinations are based on many factors including power base, client weight and client dimensions. Please call customer service with specific questions and applications.

4 PRODUCT REFERENCE: UPLIFT Designed to assist clients with forward transfers, this system can achieve a near standing position by mechanically opening the back angle and extending the platform while the seat is lifted forward. Not modular, not available with posterior tilt. Also see anterior tilt. HORIZONTAL TILT The horizontal tilt system is an innovative, highly adjustable power positioning system that can be configured for a client to operate in a prone, supine or side lying position. It features a unique, adjustable center section with telescoping, angle-adjustable supports on both ends to assist with visibility, repositioning and transfers. LATERAL TILT Our lateral tilt module enables a tilt or tilt/recline system to tilt laterally (side to side) in either direction. The system can also tilt or tilt/recline when laterally tilted. This feature is effective for pressure reduction, as well as aiding in client transfers, and can also help alleviate digestive pressure and respiratory issues. SEATING The Invacare Matrx seating line provides expert seating solutions for a wide range of client needs, from cushions and bases, to backs and other accessories. These amazing products can help maximize comfort, give support and stability for a wide range of clients pediatric to geriatric, from those with limited mobility to more active individuals. ACCESSORIES Our selection of unique accessories has been created to enhance your clients comfort, positioning, stability, and quality of life. VENTILATOR SUPPORT OPTIONS A variety of vent trays and battery trays are available to suit many clients needs. Vent battery trays are ideally mounted onto the power base rather than on the back of the seating system, to ensure that the additional weight is distributed properly for stability. Our vent trays and battery trays are typically designed to maintain a short profile, so as not to compromise the drive characteristics of the power base. O2 HOLDER We offer a variety of both fixed and articulating O2 holders. Whether your clients use a portable liquid unit or a compressed gas cylinder, our sturdy, durable steel O2 holders accommodate most sizes and shapes of O2 cylinders from the most popular portable unit manufacturers. FRONT RIGGING Our wide range of power and manual front riggings are available in an array of styles and sizes to help secure and position clients legs. In addition, we carry a multitude of legrest hangers to accommodate your front rigging choice. ARMREST Our sturdy and durable armrests help support the arm with minimal play, and can be flipped back for easy, obstruction-free side transfers. We offer an extensive variety of easily adjustable and removable armrests for virtually all client needs, from pediatric to bariatric. SPECIALIZED SEATING Our talented team of product designers and engineers quickly adapt or create customized, market-driven, and often groundbreaking solutions to meet individual clients needs. These systems are uniquely built and customized, and many become part of our standard product offering, as market demands dictate. ELECTRONICS Our state-of-the-art electronics allow users to operate their power positioning system in a simple and safe manner. Our electronics range from programmable motor control relay boxes, power cables and actuator harnesses, to a wide range of operating switches, toggles and specialized controls. System electronics will vary with the complexity of the seating system to which they apply and the type of power base on which they are installed. Designed to interface with all power base electronics platforms and specialty drive controls including Q-Logic, MK6, RNet & DX2.

5 POSITIONING OPTIONS: ULTRALOW MODULAR SYSTEM F-SERIES TILT SYSTEM BARIATRIC SYSTEM PEDIATRIC SYSTEM ELEVATE ONLY SYSTEM ULTRALIFT SYSTEM RECLINE WITH POWER SLIDING BACK SYSTEM INTERFACE SYSTEM PRECLINE SYSTEM 3

6 POSITIONING OPTIONS: ANTERIOR TILT & ASSIST SYSTEM UPLIFT SYSTEM LATERAL TILT SYSTEM HORIZONTAL TILT SYSTEM LATITUDE SYSTEM ATTITUDE SYSTEM HIGH PIVOT MECHANICAL SHEAR REDUCTION MODULE SLING SEAT SYSTEM ADJUSTABLE HI-PIVOT PRECLINE SYSTEM 4

7 INVACARE MATRX CUSHION & BACK OPTIONS: MATRX PS CUSHION KID*AB*RA CUSHION MATRX VI CUSHION MATRX VI FABRIC OPTIONS MATRX FLO-TECH CUSHION Onyx Fabric Option Fusion Fabric Option Pediatric: 12", 14" W x 12", 14" & 16" D; 150 lb weight capacity Standard: 16", 18" & 20" W x 16", 18" & 20" D; 300 lb weight capacity Bariatric: 21"-30" W x 16"-30" D; 600 lb weight capacity Pediatric: 12", 14" W x 12", 14" D; 150 lb weight capacity Standard: 14", 16", 18", 20", 22" & 22" W x 15", 16", 17", 18" & 20" D; 300 lb weight capacity Bariatric: 18"-30" W x 18"-26" D; 600 lb weight capacity Onyx Cover Option: leatherette outer cover >Offered on Invacare Matrx Vi, Kid*ab*ra and PS cushions Fusion Cover Option: A combination of Onyx and Matrx outer cover >Offered on Invacare Matrx Vi, Kid*ab*ra and PS cushions Standard: 14"-20" W x 14"-21" D; 300 lb weight capacity Bariatric: 20"-24" W x 18", 20" & 22" D; 500 lb weight capacity MATRX ELITE BACK MATRX ELITE DEEP BACK MATRX ELITE FULL BACK MATRX GENERA BACK Standard: 12"-20" W x 10", 12", 14", 16", 18" & 20" H; 300 lb weight capacity >3" contour depth Standard: 14"-20" W x 12", 16", 18" & 20" H; 300 lb weight capacity >6" contour depth Standard: 16"-20" W x 20" H; 300 lb weight capacity >3" contour depth >No scapular cut-outs Standard: 16", 18" & 20" W x 16" & 20" H; 300 lb weight capacity >3" contour depth MATRX PB BACK MATRX PB DEEP BACK MATRX PB HEAVY DUTY BACK MATRX PB DEEP HEAVY DUTY BACK Standard: 14", 16", 17", 18" & 20" W x 12", 16" & 20" H; 300 lb weight capacity >5" contour depth Standard Deep: 14"-20" W x 12", 16" & 20" H; 300 lb weight capacity >7" contour depth Heavy Duty: 20", 22" & 24" W x 16" & 20" H; 500 lb weight capacity Extra Wide: 24"-30" W x 16" & 20" H; 500 lb weight capacity >5" contour depth Deep Heavy Duty: 20", 22" & 24" W x 16" & 20" H; 500 lb weight capacity Deep Extra Wide: 24"-30" W x 16" & 20" H; 500 lb weight capacity >7" contour depth 5

8 BACK OPTIONS: STANDARD REHAB BACK RECESSED PLANAR INTERFACE PLATE 7 One part construction: 12"-21" wide Two part construction: 16"-20" wide Two part construction: 21"-26" wide >Curved, rigid design >Comes with 1" foam padding wrapped over top of pan to prevent Three part construction: 27"-34" wide sliding and to protect client >Made of sturdy steel Pediatric: 12"-14" W x 12"-14" H; 150 lb weight capacity Standard: 15"-21" W x 12"-20" H; 300 lb weight capacity Bariatric: 21"-34" W x 12"-20" H; 500 lb weight capacity I BACK INTERFACE PLATE >Adjustable width interface for mounting after-market backs to Recline or Tilt/Recline ESR or PSB systems >Recessed 0.5" between back posts Standard: 16"-20" W x 12" heigh; 300 lb weight capacity Bariatric: 21"-32" W x 12" heigh; 500 lb weight capacity CONTOUR BACK HIGH BACK Three part construction: 21"-32" wide SINGLE POST BACK >Multi-adjustable interface for mounting I shaped, after-market backs on ESR and PSB systems >I Back is 3" narrower than the width of the back canes Standard: 16"-21" W x 21" H and up; 300 lb weight capacity Standard: 15"-21" W x 12", 15", 17" & 21" H; 22" W x 15", 17" & 21" H; 300 lb weight capacity Standard: 16"-21" W x 20", 22" & 25" H ; 300 lb weight capacity MESOMORPH & ENDOMORPH BACK CANES RECLINE BODY FIT POWER SLIDING BACK (PSB) >Eliminates dual back canes; folds forward for transport >Back angle adjusts in 6 increments from 91 to 127º >No charge option with UltraLow CG tilt systems >Optional with F-series tilt systems >Fits most standard tilt and/or elevate systems and requires Dual Post arm rest; accepts swing-away laterals Standard: 16"-20" W x 21"-24" H; 250 lb weight capacity EXTENDED SHEAR REDUCTION (ESR) MESOMORPH ENDOMORPH >Designed to suit clients who are wider at their trunks than at their hips or reversed >Clearance for redundant tissue at hips/lower back >Available in 1", 2" or 4" seat variances (6" total with armrest spacers) >Back canes available in 22" or 24" heights >Not available with recline >Comes in two standard width reductions of 2" or 4" >May be used with armrest spacers to provide a 6" difference >Recline canes are mounted in towards center to maintain a smaller profile >Reclining armrests are offset to help keep clients arms in a more neutral position >Available on back widths 16" or greater >Allows independent back movement up to 3" while still in synchronization with recline >Can be used with most standard Motion Concepts backs greater than 20" in height >Requires enhanced electronics for independent operation >ESR is synchronized with recline to reduce the amount of shear >Employs a linkage that slides the backrest on the backposts through the recline cycle >Adjustable shear compensation from 3" - 5" 6

9 HEAD SUPPORT OPTIONS: FIXED MOUNTING HARDWARE STANDARD HARDWARE MULTI-AXIS HARDWARE STEALTH WORLD S BEST HARDWARE >Dual pivot ball for pad orientation >Limited adjustability recommended for Contour or High backs only >Height adjustable >Includes fixed mounting clamp >Offered with Motion Concepts Standard, Stealth All Positioning and Comfort Plus as well as Onyx Auto Style headrests >Comes standard with Otto Bock, Motion Concepts Standard & Stealth Comfort Plus Pads >Height adjustable >Depth adjustable >Single point multi-axis adjustability >Upgrade option for Otto Bock, Motion Concepts Standard & Stealth Comfort Plus pads >Dual pivot balls for pad orientation >Depth adjustable through horizontal slide bar >Height adjustable >Includes mounting clamp for attachment to back with knob style release for headrest removal >Upgrade option for Otto Bock, Motion Concepts Standard & Stealth Comfort Plus Pads >Dual pivot balls for pad orientation >Depth and height adjustable through dual link system >Includes mounting clamp for attachment to back with latch style release for headrest removal MOTION CONCEPTS STANDARD HEADREST STEALTH ALL POSITIONING HEADREST STEALTH NINO COMFORT PLUS HEADREST STEALTH COMFORT PLUS HEADREST ONYX AUTO STYLE HEADREST >Easy to clean self-skinning polyurethane foam >Gentle lateral contouring >Available in 1 pad size: Size: 6.5" W x 7" H >Soft, comfortable layered foam on coated metal shell >Removable, washable cover >Available in 2 pad sizes: Large: 9.75" W x 1.75" D x 5.25" H X-Large: 12" W x 3" D x 6" H >Soft, comfortable layered foam on coated metal shell >Removable, washable cover >Available in 1 pad size: Size: 6" W x 3.75" H >Soft, comfortable layered foam on coated metal shell >Removable, washable cover >Available in 4 pad sizes: X-Small: 6" W x 6" H Small: 8" W x 6" H Medium: 10" W x 6" H Large: 14" W x 6" H >Onyx leatherette cover >Auto-style contouring >Available in 1 pad size: Size: 8" W x 4" D x 8" H 7

10 VENTILATOR, O2 HOLDER & IV POLE OPTIONS: BACKPACK LTV COMPACT STYLE VENT TRAY ARTICULATING VENT TRAY GIMBAL VENT TRAY >Designed to carry the latest, most compact vent systems >Allows use of the "TBS" system (self contained vent and battery in carrying case), which includes the Lithium Ion battery >Adds 4" to overall length of the system >Articulating or clamp mount >Allows for easier transfers with ventilator still attached >Holds units up to 11" W x 8" D x 13" H >Designed for use with the latest, most compact vent systems >Fits standard Motion Concepts backs >Held firmly in place with removable, quick release protective front or one piece, easy access cover >Clear acrylic view window to monitor vent activity >Battery options: M40, U1, 22NF or Lithium Ion, depending on base >Articulating or clamp mount >Holds units up to 11" W x 4" D x 13" H >Available with Tilt and Recline systems >Maximum 45 of Tilt and 174 Recline travel >Vent tray stays level through travel range >Holds units up to: Vertical: " W x " D x 13" H Horozontal: 14" W x 15" D x 10" H >Pivots freely through movement during Tilt and Recline >Fits virtually all available vent types >Rubber stopper helps cushion vent movement >Available with or without battery tray >Holds units up to 14" W x 15" D x 10" H LIQUID O2 HOLDER O2 GAS CYLINDER HOLDER ARTICULATING COMPACT OR LAPTOP VENT TRAY WITH O2 GAS CYLINDER HOLDER IV POLE >Specifically sized to accommodate many of the more popular portable unit manufacturers >Articulates to keep cylinders vertical during Tilt and Recline, ensuring liquid does not drip out >Holds units up to 6.5" W x 4.5" D >Accommodates steel and aluminum D & E size cylinders, and others in the 16"-24" range with a maximum diameter of 4.875" >Optional articulation helps keep cylinders upright and prevents interference with the base >Maximum 45 of Tilt travel >Designed for use with the latest, most compact vent systems >O2 gas cylinder holder can mount along with any of the vent trays >Accommodates steel and aluminum D & E size cylinders, and others in the 16" - 24" range with a maximum diameter of 4.875" >Holds units up to 11" W x 4" D x 13" H >Telescoping 6 positions >Chrome finish >Articulating or non-articulating 8

11 FRONT RIGGING OPTIONS: FIXED STANDARD PLATFORM ADJUSTABLE 70º - 90º CENTER MOUNT FOOT PLATFORM WITH CALF PADS INDEPENDENT ELEVATING & ARTICULATING LEGRESTS (CENTER MOUNTED) 70 HEAVY DUTY SWING-AWAY FOOTRESTS WITH CAMLOCK >Standard, durable foot platform >Included with most standard front rigging orders >Three extension ranges from 9" - 21" >Leg angle can be set to 4 different angle settings 90, ±7 or +12 >Made of steel >Foot platform Size: 12" W x 10.75" D; 0.125" thick with built-in heel wells >Additional sizes, heel straps and calf pads are available >Leg angle can be set to 4 different angle settings 90, ±7 or +12 >Fits seat widths 11" - 22" >Foot platform is adjustable from 90 to -15 >Height adjustable from 9" - 21" >Comes standard with individual flat calf pads; heel loops are optional >Foot platform Size: 12" W x 10.75" D; 0.25" thick >Made of durable aluminum >Can be installed at multiple positions across the front of the chair >Independent angle adjustable foot plates >75 range of motion, from 90 resting to 165 extended >Extended articulation of 6", depending on extension length >Footplates flip back for transfers >Allows front rigging to swing in or out, and lock into position securely each time >Eliminates the need to lift the footrest, just unlock and swing to the side >Camlock receivers interface with Motion Concepts Pivot Plus Elevating Legrests or Heavy Duty Swing-Away Footrests >Available in straight or offset receiver style >Optional Lock Open feature LNX - POWER CENTER MOUNT FOOT PLATFORM >The slotted extension bracket yields a knee-to-heel range of 13" -19" (measured from seat pan to top of footplate). Adjustments are unlimited within the slotted channel length >Pivot point sits below the seat pan and has 4 fixed settings: 90, ±7 or +12 >External, adjustable microswitches allow easy setting of both home and final elevation positions >Comes standard with malleable one-piece calf panel and angle adjustable single foot platform >Optional, independently height and angle adjustable, individual pivoting calf pads >Optional split foot plates >Split foot plates are independently height and angle adjustable. Foot plate height disparity of up to 4" between right and left sides possible POWER FLIP-UP FOOT PLATFORM OPTION ON LNX >The NEW Power Flip-up Foot Platform option on the LNX uses a power mechanism to quickly flip-up the foot platform for easy forward transfers >Auto release feature protects mechanism against impact and allows manual flip-up of the foot platform >Integrates seamlessly with all one-piece foot platforms available on the LNX including extra large sizes 9

12 FRONT RIGGING OPTIONS: SWING-AWAY POWER ELEVATING PIVOT PLUS LEGRESTS WITH CAMLOCK RECEIVERS CMX - CENTER MOUNT ARTICULATING FOOT PLATFORM CMB - BELT ADJUSTABLE CENTER MOUNT ARTICULATING FOOT PLATFORM MANUAL POWER >This center mount articulating foot platform has a quiet, powerful direct drive actuator and 75 of elevation from starting position >Pivot point sits below the seat pan, leg angle can be set to 3 different angle settings 90, ±7 >Up to 7" of foot platform articulation depending on lower leg length with adjustable plantar flexion at the beginning of range which can help reduce stretching of hamstring and calf muscles >Dynamic calf pads that support lower legs through elevation >Our design allows the amount of foot platform articulation to be tightly controlled, with the added benefit being a non-fixed legrest extension tube that retracts when contact is made with a hard surface (i.e. the floor, curbs, etc.) >Pivot point sits at the seat pan and like LNX & CMX the CMB, leg angle can be set to 3 different angle settings 90, ±7 >Accommodates short leg lengths and the articulation of the foot plate can be adjusted from 3" to 7.25" >Standard one-piece calf panel or optional individual calf pads are available >Integrated power actuator allows the legrest to easily swing-away without unhooking the actuator >Leg has free movement around the front of the chair to aid in positioning and transfers >The Swing-Away Calf Pad mechanism allows calf pads to drop or flip back behind the client s calves for convenience >Straight or flared outward receivers available >Rollers on footplates assist in opening doors >Rollers on down tubes also prevent legrests from digging into ground >Extension lengths: Short: 12" - 16" Medium: 15" - 19" Long: 18" - 21" BARIATRIC ELEVATING AND ARTICULATING CALF PANEL TAPERED MANUAL ELEVATING FOOT CAGE VERTICAL LIFTING PLATFORM >Width and depth adjustable >Velcro adjustable calf strap >Manual lever for elevation adjustment can be mounted on either left or right side Footplate size: 8.5" W x 7.25" D >Platform has 11" of available vertical travel >Weight capacity of up to 200 lbs. >Chair must be driven in 5 of pre-tilt >Available on UltraLow Tilt, Tilt/Recline and Elevate systems >Designed to address the unique positioning, transfer and weight distribution needs of bariatric clients >Elevating Calf Panel articulates to reduce calf shearing >Available on systems up to 36" wide; 600 lb weight capacity >Available with Power Sliding Seat Systems 10

13 FOOT PLATE & FOOT PLATFORM OPTIONS: INDIVIDUAL FOOT PLATE OPTIONS FOR INDEPENDENT ELEVATING & ARTICULATING LEGRESTS (CENTER MOUNTED) MULTI-AXIS FOOTPLATE MOUNT >Foot shaped with heel loop Size: 6" W x 11" D (each) >Solid clamping mechanism securely locks footplate in virtually any position >Low-profile clamp is adjusted with one tool >Able to capture complex positions of foot and ankle >Interfaces with all Motion Concepts footrests FLIP-UP FOOT PLATFORM OPTIONS FOR POWER & MANUAL CENTER MOUNT FRONT RIGGING Small: 12" W x 8.5" D Medium: 12" W x 10.75" D Large: 17" W x 14.75" D Extra Large: 21" W x 14.75" D INDIVIDUAL, CAST ALUMINUM FOOT PLATE OPTIONS FOR CMB, CMX, LNX AND FIXED & ADJUSTABLE CENTERMOUNT PLATFORMS > Built in heel cups & rubber mat Small: 5" W x 7.5" D (each) FOOT PLATE OPTIONS FOR ELEVATING AND TILT FRONT RIGGING > Built in heel cups & rubber mat Medium: 5.5" W x 9.5" D (each) > Built in heel cups & rubber mat Large: 6" W x 11.5" D (each) Small: 4.25" W x 8" D (each) Medium: 5.25" W x 8" D (each) Large: 6.25" W x 8" D (each) Extra Large: 9" W x 11" D (each) Small: 7.25" W x 9" D (each) Medium: 7.5" W x 11" D (each) Large: 10" W x 14" D (each) 11

14 ARMPAD & ARMPAD ACCESSORY OPTIONS: 1. STANDARD ARM PADS 2. WATERFALL ARM PADS GEL ARM PADS MULTI-POSITION FLAT ARM PAD WITH BUMPER GUARDS ERGONOMIC ARM TROUGH FLAT HAND PAD 1 2 STANDARD ARM PADS >Standard on all Motion Concepts systems >Sold as a pair or individual >Available in 2 sizes: Full: 2.25" W x 14" L Desk: 2.25" W x 10" L WATERFALL ARM PADS >Pad is shaped to 'fall' over armrest bar >May be mounted inward or outward >Sold as a pair or individual >Available in 2 sizes: Full: 2.25" W x 14" L Desk: 2.25"W x 10" L >Fabric covered polymer gel arm pads >Provides extra protection for highly sensitive arms >Available in 3 sizes: Narrow: 2" W x 12" L Wide: 3.5" W x 12" L Long: 3.5" W x 14" L >Soft, gel-like feel provides extra comfort and protection for arms >Highly durable skinned polyurethane with bumper guards protect against cracking and peeling >Triple track extrusion allows adjustability of mounting position and attachment location for other accessories >Available in 2 sizes: Full: 3" W x 14" L Desk: 3" W x 10" L ERGONOMIC ARM TROUGH >Molded, skinned polyurethane >Ergonomic shape fits the natural arm curvature >Unique cut-out at elbow provides users with flexibility of various arm positions >Triple track extrusion allows a variety of mounting positions >Modular hand pads from other manufacturers may be interfaced using special adapter (see below) >Available for left or right side Size: 4.5" W x 13" L FLAT HAND PAD >Hand pad is an optional add-on and available for left or right side Pad Size: 4.5" W x 5" L ELBOW BLOCK STEALTH SWING-AWAY ELBOW STOP ARMPAD ACCESSORIES ARMREST ADJUSTMENTS A C D B B A >Prevents arms from falling back while tilted >Can be positioned to provide comfortable support to upper arms >Easily removable, multi-adjustable mounting available in 3" or 5" of vertical extension and 5" or 7" of horizontal extension >Rotational pad adjustment >Available in 4 pad sizes: X-Small: 4.25" W x 3.25" H Small: 5.25" W x 3.5" H Medium: 7.75" W x 3.75" H Large: 6.5" W x 4.25" H >Uses Stealth adjustable swing-away system to comfortably support client s elbows and upper arm >Available in 3 sizes: Small: 3" W x 3" H Medium: 4" W x 4" H Large: 10" W x 3" H (U shaped) A- Otto Bock FLAT HAND PAD B - Otto Bock ACCESSORY ADAPTER >For adding Otto Bock modular hand pads to Motion Concepts Ergonomic Arm Trough (see above) C - ARMREST EXTENSION TUBE >Extends arm pads 3.5" D - ARMREST EXTENSION TUBE >Extends arm pads 7" A - ARMREST SPACERS >Allows 0.5" or 1" space in armrest mounting >May use one or two spacers >Beneficial in growing seat widths B - ARM PAD OFFSET EXTENSION >Moves arm pad 0.75" out or in >Stability for mounting flat accessories and arms to round tubes 12

15 ARMREST OPTIONS: HEIGHT AND ANGLE ADJUSTABLE CANTILEVER FLIP BACK TILT ARM WITH CAMLOCK RECLINING ADJUSTABLE HEIGHT ARMREST HEIGHT AND ANGLE ADJUSTABLE CANTILEVER FLIP BACK RECLINE ARM WITH QUICK LOCK MECHANISM HEIGHT AND ANGLE ADJUSTABLE CANTILEVER FLIP BACK RECLINE ARMREST >Latch Plate permits the attendant to release the armrest to be flipped back >12 of angle adjustment >In the upright position armrest can be adjusted to the desired angle >Flip back and removable for easier transfers >Height adjustable in 2 ranges: Standard: 9.5" H- 18.5" H Pediatric: 7.75"H - 10" H >Adjustment range is 3" >Locks armrest in down position for stable transfer/re-positioning surface >Optional for Tilt or Recline Cantilever arms >Easy access release mechanism >Arm retains ability to flip back completely >Designed for Recline and Tilt/Recline Systems >Armrest can be configured to be parallel or perpendicular to the seat frame when fully reclined >Arm retains ability to flip back completely >Independent height and angle adjustment DUAL RELEASE LOCKING ARM - Single hand release ATTENDANT MODE CLIENT MODE OPTIONAL FOR RECLINE SYSTEMS RECLINE CANTILEVER ARMREST >Designed to pivot around its mounting point for easy side transfers >Trigger Switch and Latch Plate permits the user and/or attendant to release the armrest with one hand >Armrest can be configured to be parallel or perpendicular to the seat frame when fully reclined >In the upright position armrest can be adjusted to the desired angle >Can accommodate arm heights as low as 8.25" 13

16 ARMREST OPTIONS: ADULT DUAL POST ADJUSTABLE HEIGHT ARMREST PEDIATRIC ADJUSTABLE HEIGHT ARMREST GLOVE BOX CUP HOLDER/STORAGE ARMREST >Durable, precision machined rear pivot for long-term stability and tolerance >Flip back and removable for easy transfers >Height adjustable in 3 ranges: Small: 9.75" H " H Medium: 12.75" H " H Large: 15.75" H " H >Optional quick height adjustment lever available at nominal upcharge >Specially created and scaled down for kids >Durable, precision machined rear pivot for long-term stability and tolerance >Flip back and removable for easy transfers >Height adjustable in 3 ranges: Small: 6" H - 7.5" H Medium: 6.75" H " H Large: 8.25" H - 9" H >Sleek and modern automotive look >Quad release and closure for clients with limited dexterity >Made of sturdy, durable material >Available on Motion Concepts dual post arms only >No charge option with UltraLow systems >Retractable cup holder fits most standard cans or bottles >Arm pad flips open to store items >Comfortable, padded armrest >Available for left or right side Size: 4" W x 14" L POWER FLIP BACK DUAL POST ARM OUTBACK ARM POWER OR MANUAL FLIP DOWN TRANSFER ARM >Arm is powered to flip back 90 >Available on UltraLow CG tilt systems and elevate-only systems which utilize a dual post, height adjustable armrest >Height adjustment is not compromised with the power flip back feature >May be used with dual post height adjustable arms with quick height adjustment lever >All arm pad options are still available >Elbow blocks may be added >Available for left or right side >Available for the Motion Concept s dual post tilt armrest or the recline armrest >OutBack Arm pivots 30 outward to allow clearance for Arm Troughs, lateral supports and other positioning components MULTI-AXIS UPPER EXTREMITY SUPPORT >Single locking bolt or ratchet allows infinite adjustment of angle and rotation of armpad or arm trough >Ability to capture complex positions of client s arm/hand >Universal 0.875" clamp which allows it to fit on any wheelchair armrest, manual or power >Low profile bracket easily interfaces with the Motion Concepts gel armpad, Arm Trough or Multi-Position Flat Armpad >Transfer arm available with power or manual drop down function >Power version operates through a separate switch or through the joystick control >The manual version uses a small manual linkage located at the bottom of the armrest >Client can slide/shuffle along seat pan onto armrest for easy transfer >Weight capacity: up to 200 lbs >Available left or right 14

17 LATERAL HIP AND TRUNK SUPPORT OPTIONS: LATERAL HIP/KNEE SUPPORT WITH SWING-AWAY REMOVABLE HARDWARE LATERAL HIP SUPPORT WITH FIXED OR REMOVABLE MOUNTING HARDWARE >Flexible mounting locations at hip, knee or both >Height and depth adjustable >Rotational adjustment at pad and clamping bar for maximum abduction and adduction adjustment >4 pad sizes available: (see below) >2.5" of height adjustment in 0.625" increments. >Low profile hardware does not interfere with armrests >Each hip support pad can be moved forward and back on bracket in 1" increments >Lateral hip pad standard with fixed hardware >Optional removable hardware upgrade >4 pad sizes available: (see below) HIP PAD SIZES XS: 5.5" W x 4" H S: 7.5" W x 6" H M: 9" W x 4" H L: 13" W x 4" H LATERAL TRUNK SUPPORTS WITH STEALTH PUSH BUTTON TELESCOPING SWING-AWAY MOUNTING HARDWARE LATERAL TRUNK SUPPORTS WITH FIXED HARDWARE LATERAL TRUNK SUPPORTS WITH SWING-AWAY HARDWARE >Easy to access, push button release >Low profile design does not interfere with flip back armrests >180 swing-away mechanism prevents damage to lateral hardware >2 Stealth lateral pad sizes: (see below) >Designed especially for Contour or High backs providing infinite/easy adjustability up and down >4 pad sizes available: (see below) >Designed especially for Contour or High backs providing infinite/easy adjustability and obstruction-free transfers >4 pad sizes available: (see below) STEALTH LATERAL PADS LATERAL PAD SIZES S: 5" W x 3" H L: 6" H x 4" W XS: 3.25" H x 4.25" W S: 3.5" H x 5.25" W M: 3.75" H x 5.75" W L: 4.25" H x 6.5" W 15

18 INVACARE MATRX ELITE LATERAL SUPPORT OPTIONS: SWING-AWAY LATERALS OFFSET SWING-AWAY LATERALS FIXED LATERALS OFFSET FIXED LATERALS RANGE OF ADJUSTMENT (VIEW OF HARDWARE MOUNTED INSIDE THE BACK SHELL ) >Designed especially for Invacare Matrx Elite backs > 2.5" of vertical adjustment on back pan > Mount inside back shell without interfering with depth/angle adjustment > Easy push button release >Available for left or right side >4 pad sizes available: (see below) >Designed especially for Invacare Matrx Elite backs >Provides an additional 3" of vertical position (higher or lower) relative to mounting slots > Mount inside back shell without interfering with depth/angle adjustment > Easy push button release >Available for left or right side >4 pad sizes available: (see below) >Designed especially for Invacare Matrx Elite backs > 2.5" of vertical adjustment on back pan > Mount inside back shell without interfering with depth/angle adjustment >Available for left or right side >Available in 2 sizes: Standard: 7.5" L - 5" H Pediatric: 5.5" L - 3" H >Designed especially for Invacare Matrx Elite backs > Provides an additional 3" of vertical position (higher or lower) relative to mounting slots >Available for left or right side >Available in 1 size: Standard: 7.5" L - 5" H LATERAL PAD SIZES XS: 3.25" x 4.25" S: 3.5" x 5.25" M: 3.75" x 5.75" L: 4.25" x 6.5" 16

19 POSITIONING OPTIONS: POWER HEADREST POWER SWING-AWAY CHIN AND/OR CENTER LINE MOUNTING SYSTEM POWER SWING-AWAY JOYSTICK >Headrest can retract backward up to 4" and lower out of the way up to 3" >Fits any standard Motion Concepts back >Can be controlled with separate switch or as an additional switch on a multi-function system >Must be ordered through request for quotation (RFQ) >Call customer service for details MEMORY SEATING >Can be used for mounting of drive controls and/or power positioning controls >Uses a switch boom, swings away to free client s face from obstruction >Can be used on all standard Motion Concepts backs >May be mounted on left or right side >Allows client to adjust height of chin control in 1.5" range before it swings away >Power Swing-Away feature allows Joystick to be repositioned for client comfort, transfers and/or environmental access FLIP AND FOLD AWAY LAP TRAY ATTENDANT SWITCH FOR MEMORY SEATING M99 & SENSOR MODULE 17 >One command can control the position of up to four independent actuators >Ability to program up to four different memory positions >Available in single or multiple power function configurations >Seamless integration with drive controls from Invacare, Quantum Rehab and Quickie using Motion Concepts enhanced electronics >May also be controlled through separate switch or toggle >Able to control tilt, recline, and power front rigging, including independent elevating leg rests >Can either read the function position from the built-in feedback of the actuators or use simple 1" x 1" add-on sensors attached at each moveable axis on the chair >Flip and Fold Away Lap Tray is an angle adjustable lap tray that flips up and rotates back out of the way or removes completely when not in use >Can be attached to most wheelchair armrests >Hardware also available to mount communication board or laptop computers

20 POSITIONING OPTIONS: PUSH AND TRANSFER HANDLES POWER SWING-AWAY BACKPACK SAFETY LIGHT KIT A B C D E A- HEIGHT ADJUSTABLE TRANSFER HANDLES > Height adjustable from 3.5" - 6" > Mounted to seat frame > Foam rubber grips > Increments of 3.625" " B- BENT ANGLED PUSH HANDLES > 5" rise, 5 out angle, mount to angled section of Motion Concepts pushbar C - ANGLED PUSH HANDLES > 5" rise, 5 out angle, mounts to flat section of Motion Concepts pushbar D - STRAIGHT PUSH HANDLES >5.5" from center of Motion Concepts pushbar E- STRAIGHT ANGLED PUSH HANDLES > 5.5" offset and 5 angle from center of Motion Concepts pushbar >Backpack swings around 270 from home position to side of chair in order to provide users with access to stored items >Available in right and left versions >Operated through separate switch and motor control box or wheelchair drive controls >Available on tilt only systems. Recline and Tilt/Recline via request for quotation (RFQ) >50 lbs pack storage capacity >Front or Rear lights are available as a set of 2 with any UltraLow system >Provides extra visibility and illumination in dark or low light areas >Lightweight and visually pleasing >Uses low voltage LED lighting with power from base >Cool to the touch LED for client safety MULTI-MOUNT HARDWARE KIT POWER SLIDING SEAT >Power sliding seat provides up to 6" of fore and aft movement for transfers and optimal balancing of client weight >When system is in its most forward position the elevating and articulating calf panel remains tucked under the front of the seat for unrestricted transfer >The seat then slides back to the home position effectively balancing the system for clients with a disproportionate amount of weight forward >Multi-mount kit offers unlimited combinations for mounting push buttons and toggle switches >Provides mounting solutions for Multi-position Flat arm pads, Ergonomic Arm Troughs, armrest tubes and multi rails >Standard with all Motion Concepts systems 18

21 ELECTRONICS OPTIONS: All Motion Concepts electronics are designed to ensure the smooth and seamless operation of every power positioning system we manufacture. From the UltraLow tilt to our most customized power positioning solution, each electronic component is designed with the flexibility and modularity needed to provide years of safe and reliable service. MOTOR CONTROLLER STANDARD FEATURES INCLUDE: >A standard, accessible attendant switch to control the power seating functions or the ability to add one > Soft start and soft stop provide a smooth, easy transition and eliminate quick, jerky tilts or hard stops at the beginning and end of any command >Drive lockout with SMARTS to eliminate mercury splash > Standard, independent, variable speed actuator control of up to six controls > Designed to interface with all power base electronics platforms and specialty drive controls including Q-Logic, MK6, RNet & DX2. MOTOR CONTROLLERS: SINGLE FUNCTION CONTROL BOX NEW SINGLE FUNCTION CONTROL BOX ENHANCED CONTROL BOXES HELIX SIGMA MULTI FUNCTION CONTROL BOX M130 M33 M27 HELIX 1.0 The single function control box controls one seating function through a separate switch, toggle, or through the wheelchair drive controls. >Adjustable speed control M130 SINGLE FUNCTION This new single function control box controls one seating function through a separate switch, toggle, or through the wheelchair drive controls: >Less than half the size of the Helix 1.0, with the same power output >Utilizes new Molex connector harness for actuator power >New, compact, integrated moulded limit switch cables for cleaner installation and mounting M27 ENHANCED SINGLE FUNCTION M33 ENHANCED DUAL FUNCTION Single and dual function enhanced motor control boxes provide the same function as our standard motor control boxes with several additional functional benefits. These control boxes are designed to operate power positioning functions through a separate switch or toggle box, or can be interfaced to allow operation of the power positioning system through the wheelchair drive controls. Enhanced motor control boxes offer additional functions, such as: >Accessible attendant control toggle switch standard on top of box >LED on top of box provides visual confirmation when chair is in home position, reduced drive or drive lockout (DLO) >Variable speed dials are accessible on outside of box for independent control of actuator speeds without programmer HELIX SIGMA Our enhanced multiple function control box provides maximum modularity, programmability and function to meet virtually any application. This control box is able to control from one to seven power positioning functions while also offering the following features: >Standard tipsy angle sensor and reduced drive speed >Ability to drive while elevated >LEDs on top of box provide visual confirmation of drive lockout, reduced drive and home functions >Variable speed control and attendant control for up to six motors 19

22 HARNESS AND CABLE OPTIONS: M73 INTERFACE CABLE M91 INTERFACE CABLE SPECIALTY CONTROL ECU CABLES M11 TIPSY MULTI-POSITION ANGLE SENSOR PROGRAMMER C64 SENSOR C39 TWO SIGNAL FUNCTION CABLE >Allows interface to Motion Concepts seating with PG, Q-Logic, MK6, RNet & NE drive controls >Female DB9 connector MULTI FUNCTION SIGNAL FUNCTION CABLE >Controls up to five functions >Allows interface to Motion Concepts seating with Q-Logic drive controls >Female DB9 connector >Specialty control ECU cables are used to interface alternative controls and ECU boxes to Motion Concepts systems motor controllers (Helix Sigma) >Male/Female DB9 connectors C64 PROGRAMMABLE CABLE >Enables changing of pin outputs >Sleek, sealed, single plug design replaces multiple mercury switches and plugs >Easy, push button with drive lockout, reduced speed and tilt limit settings >In hand programming >Works in conjunction with Helix Sigma C39 FIXED PIN CABLE >Connects ECU cables to Motion Concepts control boxes M25 PG REDEL SPLITTER BOX M80 PG ADAPTER HERCULES POWER BOOSTER DIRECTIONAL LIMIT CONTROL > For use with PG drive control systems (Quickie or Quantum) >Allows two extra Redel ports to be added to PG system for additional interfacing of attendant drive controls, etc. >Provides seamless interface between Helix Sigma, M27 or M33 allowing user to control one or two functions through PG drive controls (Quickie or Quantum) >User still retains all functions provided in Helix control boxes including operations of system >Female DB9 connector >Enhances power for heavily loaded systems, up to 500 lbs >Designed with a down limit shut-off >M59Bi Programs independent limits to any single motor >Can program the beginning and ending ranges of any single motor using adjustable limit switches C53 ACTUATOR POWER BY-PASS CABLE MACH-C MULTIPLE ACTION CUSTOM HARDWARE CONTROL SEAT FUNCTION DISPLAY S-06 ATTENDANT POWER SWITCH >Standard on all systems where battery access can be hindered when batteries have been depleted beyond charging and require replacement >Connects between the existing actuator cable and the elevating actuator >By-passes system batteries to operate elevator and service power base >Works with 12 Volt or 24 Volt power source >Used to configure industry standard 2 and 4 way inputs to multiple chair control options >Provides the ability to program what each switch or toggle command controls in the power positioning system. Maximum 12 switches, 2 DB9 ports >Maximizes the functional control of each user and their system >Programming specialty controls and joystick operations of Power Positioning Systems >New serial seat function display with single moulded cable that plugs directly into the seat controller box >Scrolls /scans functions enabled in the controller box to allow for direct mode or toggle mode operation >Bright blue backlit display with bold white lettering >Single switch instantly shuts down all power to the entire wheelchair seating system (attendant or client use) >Overrides unintentional and unauthorized control of power positioning functions >Power on status is indicated with red LED light >Places power base in drive lockout 20

23 HARNESS AND CABLE OPTIONS: C366 EXTENSION CABLE C366-F (FUSED) EXTENSION CABLE C61 EXTENSION CABLE C201 Q-LOGIC BUS CABLE >Available in 4 lengths: 15", 18", 22" & 36" >Used for standard actuators >Cables used to connect actuator to C365 cable on UltraLowII >Fused for MBL actuators >Used to extend a cable length >Used to connect AAM to controller on Q-Logic C365 CABLE C300 PS24 POWER OUTLET >Breakout box for connecting Helix box to actuator harness (C365) >Small, high-current molex extension cables with black pvc conductor covering >Sized perfectly for each individual function >Smaller connector profile makes for easier and cleaner wire routing and service >Used to connect Helix Sigma HSE to MK6 controller >Allows control through joystick and OFF setting at the same time >Provides ability to charge any device with 12 Volt power source (auto power plug) from power base batteries >In-line power harness is compatible with all Motion Concepts controller harnesses >Durable case with weather resistant rubber cap >Output Volts DC, maximum output 3 AMPS 21

24 MECHANICAL SWITCH OPTIONS: S-19 SINGLE TOGGLE BOX STEALTH EGG SWITCH M07 LAZARUS JUMP STARTER TOGGLE BOXES S-37D S-38 S-26 Allows control of one function in direct mode or two functions in auto reversing mode >Includes drive lockout (DLO) indicator >Female DB9 connector M16 SPLITTER BOX >A large 3" x 1.5" egg shaped push button with a 52" long cable and a 0.125" mono phono connector >Available in green or black >Mono connector >Sleek, compact box accommodates up to five mechanical switches >Converts five separate mechanical switch inputs into one industry standard female 9 pin connector >Useful when multiple mechanical switches are located in several different locations on chair >For use with 0.125" plugs >Battery charger booster >When the battery voltage levels drop too low for the automatic charger to start charging, the Lazarus sends the required signal to begin charging >Durable push button start switch >Charging status indicated with green LED light >Must be used in conjunction with off-board charger S-37 & S-37D SINGLE (stereo connector) Allows control of one function in direct mode or two functions in auto reversing mode >Low voltage toggle S-38 DUAL (female DB9 connector) Allows control of one function in direct mode or two functions in auto reversing mode >Includes drive lockout (DLO) indicator S-26 FOUR WAY (female DB9 connector) Allows control of two functions in direct mode or four functions in auto reversing mode >Includes drive lockout (DLO) indicator FEATHER TOUCH SWITCHES PUSH BUTTON SWITCHES A B C D A B C D >Limited force capacitive touch switch >Available in single, dual and quad button configurations A - S01 "QUARTER SIZE" SINGLE FUNCTION SWITCH (mono connector) B - S02 SMALL "DIME SIZE" SINGLE FUNCTION SWITCH (mono connector) C - S32T "DIME SIZE" DUAL FUNCTION SWITCHES (female DB9 connector) D - S34T "DIME SIZE" QUAD FUNCTION SWITCH (female DB9 connector) A- S31 SINGLE PUSH BUTTON SWITCH (mono connector) >Allows control of one seating function in auto reversing mode B - S32P DUAL PUSH BUTTON SWITCH (stereo connector) >Allows control of two functions in auto reversing mode or one function in direct mode C - S32D DUAL PUSH BUTTON SWITCH (female DB9 connector) >Allows control of two functions in auto reversing mode or one function in direct mode D - S34 Quad PUSH BUTTON SWITCH (female DB9 connector) >Allows control of two functions in direct mode or up to four functions in auto reversing mode 22