MODEL 3700 FRONT FOLDING PLANTER OPERATOR MANUAL. M Rev. 10/11

Transcription

1 MODEL 3700 FRONT FOLDING PLANTER OPERATOR MANUAL M0330 Rev. 0/ This manual is applicable to: Forward Folding Planters Record the model number and serial number of your planter along with date purchased: Model Number 3700 Serial Number Date Purchased Monitor Serial Number Measured Pulses Per Mile/Km (Radar Distance Sensor) Measured Pulses Per Mile/ Km (Magnetic Distance Sensor) SERIAL NUMBER The serial number plate is located on the planter frame as shown below. The serial number provides important information about your planter and is needed to obtain correct replacement parts. Always provide model number and serial number to your Kinze Dealer when ordering parts or when contacting Kinze Manufacturing, Inc. Serial number plate location Kinze, the Kinze logo, TwinLine, Interplant and EdgeVac are registered trademarks of Kinze Manufacturing, Inc.

2 This page intentionally left blank.

3 M0330 To The Owner Kinze Manufacturing, Inc. thanks you for your patronage. We appreciate your confidence in Kinze farm machinery. Your Kinze planter has been carefully designed to provide dependable operation in return for your investment. This manual has been prepared to aid you in the operation and maintenance of the planter. It should be considered a permanent part of the machine and remain with the machine when you sell it. It is the responsibility of the user to read and understand the Operator Manual in regards to safety, operation, lubrication and maintenance before operation of this equipment. It is the user s responsibility to inspect and service the machine routinely as directed in the Operator Manual. We have attempted to cover all areas of safety, operation, lubrication and maintenance; however, there may be times when special care must be taken to fit your conditions. Throughout this manual the symbol and the words DANGER, WARNING, and CAUTION are used to call attention to safety information that if not followed, will or could result in death or injury. NOTICE and NOTE are used to call your attention to important information. The definition of each of these terms follows: DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE is used to address practices not related to personal injury. NOTE: Special point of information or machine adjustment instructions. WARNING Improperly operating or working on this equipment could result in death or serious injury. Read and follow all instructions in Operator Manual before operating or working on this equipment. WARNING Some photos in this manual may show safety covers, shields, or lockup devices removed for visual clarity. NEVER OPERATE OR WORK ON machine without all safety covers, shields, and lockup devices in place as required. NOTE: Photos in this manual may be of prototype machines. Production machines may vary in appearance. NOTE: Some photos and illustrations in this manual show optional attachments installed. Contact your Kinze Dealer for purchase of optional attachments. Rev. 0/

4 This page left blank intentionally.

5 M0330 Specifications Specifications Specification Conventional Hoppers Air Seed Delivery (ASD) Number of Rows R 0 R N 30 R N 30 36R N 0 Row Spacing 0" 30" 30" 0" Weight Empty (Mechanical) 8,300 lb 0,38 lb 5,80 lb 6,87 lb Weight Empty (EdgeVac),73 Transport Height 0'9" '7" 3'0" '0" Planting Length 7'" 30'" 30'" 30'" Transport Length 3'0" 36'" 0' " 0' " Planting Width 3' " 6'9" 6' 9" 63' 9" Transport Width ('0" with granular chemical option) 3'3" 3'0" 3'8" 3'8" Seed Capacity.90 bu. / hopper.75 bu. 0 bu. ASD Fill Dimensions (planting position) 8' 7" Transport Tire Size Transport Tire Pressure Wing/Lift Tires Field Tire Pressure () 36 x 67.5 rib duplex ply tubeless 75 psi ( R, 6 36R) 7.5" x 0", 8ply, Tubeless Rib Implement 0 psi Contact Drive Tires ().80 x 8" Piston Pump Drive Tires (Optional) () 7.60" x 5" Field Lift Four Master/Two Slave Hydraulics Row Markers Independently controlled, three stage, low profile equipped disk blade depth bands. Tractor Hydraulic Requirements Configuration Requirements Description Base machine with mechanical meters SCV 5 gpm # SCV: planter lift # SCV: markers / fold (with v control console) Base machine with mechanical meters Air seed delivery (ASD) system 3 SCV 5 gpm # SCV: planter lift # SCV: markers / fold (with v control console) #3 SCV: ASD system Base machine with EdgeVac meters Tractor mounted PTO hydraulic pump SCV 5 gpm # SCV: planter lift # SCV: markers / fold (with v control console) NOTE: Tractormounted PTO hydraulic pump supplies oil flow for EdgeVac hydraulic circuit. Rev. 0/ 3

6 General Safety Rules M0330. Read and understand instructions provided in this manual and warning labels. Review these instructions frequently!. This machine is designed and built with your safety in mind. Do not make any alterations or changes to this machine. Any alteration to design or construction may create safety hazards. 3. A large portion of farm accidents happen from fatigue or carelessness. Safe and careful operation of tractor and planter will help prevent accidents.. Never allow planter to be operated by anyone unfamiliar with operation of all functions of the unit. Operators must read and thoroughly understand all instructions given in this manual before operating or working on equipment. 5. Be aware of bystanders, particularly children! Always look around to make sure it is safe to start tow vehicle engine or move planter. This is particularly important with higher noise levels and quiet cabs, as you may not hear people shouting. 6. Make sure planter weight does not exceed towing capacity of tractor, or bridge and road limits. This is critical to maintain safe control and prevent death or injury, or property and equipment damage. 7. Never ride or allow others to ride on planter. 8. Store planter in an area away from human activity. DO NOT permit children to play on or around the stored unit. 9. Keep hands, feet, and clothing away from moving parts. Do not wear loosefitting clothing which may catch in moving parts. 0. Always wear protective clothing, shoes, gloves, and hearing and eye protection applicable for the situation.. Do not allow anyone to stand between tongue or hitch and towing vehicle when backing up to planter. 3. Prevent electrocution, other injuries, or property and equipment damage. Watch for obstructions such as wires, tree limbs, etc. when operating machine. Be aware of clearances during turns and when folding/unfolding planter.. Reinstall all guards removed for maintenance activities. Never leave guards off during operation. 5. Use of aftermarket hydraulic, electric, or PTO drives may create serious safety hazards to you and people nearby. If you install such drives, follow all appropriate safety standards and practices to protect you and others near this planter from injury. 6. Follow all federal, state/provincial and local regulations when towing farm equipment on a public highway. Use safety chain (not an elastic or nylon/ plastic tow strap) to retain connection between towing and towed machines in the event of primary attaching system separation. 7. Make sure all safety/warning lights, SMV sign, and reflective decals are in place and working properly before transporting the machine on public roads. 8. Limit towing speed to 5 MPH. Tow only with farm tractor of a minimum 90 HP. Allow for unit length when making turns. 9. Reduce speed prior to turns to avoid the risk of overturning. Always drive at a safe speed relative to local conditions and ensure your speed is slow enough for a safe emergency stop. 0. Chemical application is often an integral part of planting. Follow label instructions for proper chemical mixing, handling and container disposal methods.. Be familiar with safety procedures for immediate first aid should you accidentally contact chemical substances.. Use the proper protective clothing and safety equipment when handling chemicals. 3. Chemicals are supplied with Material Safety Data Sheets (MSDS) that provide full information about the chemical, its effects on exposure, and first aid needs in the event of an emergency. Keep your MSDS file uptodate and available for first responders in case of emergency.. When servicing ground engaging components such as opening disks and firming points, use special care to avoid points and edges worn sharp during use. 5. Use professional help if you are unfamiliar with working on hydraulic systems. Pressurized hydraulic fluid can penetrate body tissue and result in death, serious infection, or other injuries. Rev. 0/

7 M0330 Safety Precautions Following are some common hazard warnings associated with this equipment. Pay close attention to all safety, operating, and maintenance information in this manual and decals applied to your equipment. DANGER! Contacting or coming close to power lines or other high energy sources will cause death or serious injury. Keep away from power lines or high energy sources at all times. WARNING Improperly operating or working on this equipment could result in death or serious injury. Read and follow all instructions in Operator Manual before operating or working on this equipment. WARNING Falling equipment can cause death or serious injury. Install all lockup devices or lower planter to ground before working on equipment. WARNING Explosive separation of rim and tire parts can cause death or serious injury. Overinflation. rim and tire servicing, improper use of rims and tires, or worn or improperly maintained tires could result in a tire explosion. Safety Signs And Decals WARNING All safety/warning lights, reflective decals, and SMV sign must be in place and visible before transporting machine on public roads or death, serious injury, and damage to property and equipment may result. Check federal, state/provincial, and local regulations before transporting equipment on public roads. Safety signs and decals are placed on the machine to warn of hazards and provide important operating and maintenance instructions. Information on these signs are for your personal safety and the safety of those around you. FOLLOW ALL SAFETY INSTRUCTIONS! Keep signs clean so they can be easily seen. Wash with soap and water or cleaning solution as required. Replace safety signs if damaged, painted over, or missing. Check reflective decals and SMV sign periodically. Replace if they show any loss of of reflective properties. Clean machine surface thoroughly with soap and water or cleaning solution to remove all dirt and grease when replacing decals. NOTE: Safety sign and decal locations are shown in the Parts Manual for this machine. NOTE: Style and locations of SMV sign, reflective decals, and safety/warning lights conform to ANSI/ASABE S79. JUL 008 and ANSI/ASABE S76.6 JAN 005. Rev. 0/ 5

8 This page intentionally left blank.

9 M0330 Machine Operation Planter Lift Safety Lockup WARNING Uncontrolled machine movement can crush or cause loss of control resulting in death, serious injury, or damage to property and equipment. Install all safety lockup devices before working under or transporting this equipment. Safety lockup in storage position Safety lockup in transport/maintenance position Planter lift safety lockup is installed between lift cylinder and wheel lift arm. It is held in place by a pin and lynch pin. Remove safety lockup and store on hose takeup for field operation. Row Marker Safety Lockup WARNING Row marker can lower at any time and could cause death or serious injury. Stay away from row markers! Install safety lockup device when not in use. Row marker safety lockup stored Row marker safety lockup installed Always install row marker lockups when working on, storing, or transporting planter. Hold in place with two clevis pins. Rev. 0/

10 Machine Operation M0330 WARNING Planter hitch may raise uncontrollably during folding/unfolding and can cause death, serious injury, or damage property and equipment. DO NOT fold or unfold planter without planter attached to a tractor. DO NOT unhitch planter from tractor unless fully folded for transport or fully unfolded with planting units lowered to ground. WARNING Uncontrolled movement of equipment can cause loss of control and could result in death, serious injury, or damage to property and equipment. Install all safety pins before transporting equipment. Hitch Parallel Linkage Lockup Hitch parallel linkage pin stored Hitch parallel linkage pin installed A hitch parallel linkage lock pin locks hitch parallel linkage in raised (transport) position. Speed Jack Assembly Slow Fast Jack handle stored Jack handle installed Store jack on L.H. side of hitch. Secure in place with spring pin. Install jack on hitch post and secure in place with spring pin. Pull out on handle for high speed or push in on handle for low speed operation. Rev. 0/

11 M0330 Machine Operation WARNING Improperly operating or working on this equipment could result in death or serious injury. Read and follow all instructions in Operator Manual before operating or working on this equipment. Initial Planter Preparation Following information is general in nature to aid in preparation of tractor and planter for use, and to provide general operating procedures. Operator experience, familiarity with the machine, and the following information should combine for efficient planter operation and good working habits. WARNING Explosive separation of rim and tire can cause death or serious injury. Overinflation, rim and tire servicing, improper use of rims and tires, worn, or improperly maintained tires could result in a tire explosion. WARNING Wheel separation can cause loss of control resulting in death, serious injury, or damage to property and equipment. Check lug nuts on transport wheels are tight before operating planter for first time and periodically after. Row marker Contact drive Transport Ground drive. Torque transport wheel ¾" 6 lug nuts to 00 ftlb ( Nm).. Inflate tires to the following specifications: Tire locations Ground drive (wings) 5 x 70R.5 75 psi (57. kpa) Transport 36" x 6" x 7.5" 75 psi (57. kpa) Contact drive.80" x 8" 50 psi (3.7 kpa) Row marker 6" x 6.5" x 8" psi (96.5 kpa) Liquid fertilizer piston pump (not shown).0" x 6" 50 psi (3.7 kpa) 3. Lubricate planter and row units per lubrication information in this manual.. Check all drive chains for proper tension, alignment, and lubrication. Rev. 0/ 3

12 Machine Operation M0330 Tractor Requirements WARNING Loss of control of equipment during transport can result in death, serious injury, or damage to property and equipment. Tractor gross weight must be greater than planter gross weight with attachments and options. Consult your dealer for information on horsepower requirements and tractor compatibility. Requirements vary with planter options, tillage, and terrain. Two dual remote hydraulic outlets (SCV) are required on all sizes of conventional planters equipped with row markers. Four dual remote hydraulic outlets (SCV) are required on all sizes of ASD planters equipped with row markers. A volt DC electrical system is required on all sizes. EdgeVac Tractor Mounted PTO Pump and Planter Mounted Hydraulics Twosection PTO hydraulic pump 8 gal (30.3 L) reservoir Edgevac equipped planters require a ¾"0 spline 000 RPM PTO to operate PTOdriven two section hydraulic pump capable of supplying 5 gpm (56.8 Lpm) to two hydraulic motors/vacuum fans. EdgeVac Seed Metering System operates from an 8 gal (30.3 L) capacity oil reservoir. Oil cooler Flow control Fan block Hydraulic motor Filter Vacuum fan assembly with oil cooler Vacuum fan block and filter Other dual fan system components include two oil coolers, two replaceable cartridgetype filters, two motorized flow controls, pressure compensating valves, solenoid valves, and relief valves. Rev. 0/

13 M0330 Machine Operation Tractor Preparation and Hookup Planter control console Digital vacuum gauge control console. Install planter control console (all) and digital vacuum gauge (EdgeVac only) control consoles on tractor in convenient locations within operator reach and close to hydraulic controls. Mount control consoles securely and route power cables to power source. A power lead adapter may be required. See Lubrication and Maintenance section for wiring schematics. NOTE: Control console operates on volt DC only. If two 6 volt batteries are connected in series, make sure power connection provides volt DC across positive terminal on one battery and negative terminal of second battery. ALWAYS make power connection on battery grounded to tractor chassis.. Adjust tractor drawbar 37 inches above ground with hitch pin hole directly below PTO shaft center line. Make sure drawbar is in a stationary position. WARNING Planter hitch may raise uncontrollably during folding/unfolding and can cause death, serious injury, or damage property and equipment. DO NOT fold or unfold planter without planter attached to a tractor. DO NOT unhitch planter from tractor unless fully folded for transport or fully unfolded with planting units lowered to ground. 3. Back tractor to planter and connect with minimum ¼" diameter hitch pin. Make sure hitch pin is secured with a locking pin or cotter pin If tractor is not equipped with a hitch pin locking device. NOTE: DO NOT install safety chain using clevis mounting hardware. Safety chain MUST be installed separately.. Safety chain must be used to keep planter and tractor connected in case of a hitch pin/drawbar failure. Attach safety chain at an unused clevis mounting hole on the planter hitch. Torque hardware to 80 ftlb (38.8 Nm). Tractor and safety chain hookup Rev. 0/ 5

14 Machine Operation M0330 WARNING Pressurized hydraulic fluid can penetrate body tissue and result in death, serious infection, or other injuries. Fluid injected under skin must be IMMEDIATELY removed by a surgeon familiar with this type of injury. Make sure connections are tight and hoses and fittings are not damaged before applying system pressure. Leaks can be invisible. Keep away from suspected leaks. Relieve pressure before connecting or disconnecting tractor, searching for leaks, or performing any system maintenance. NOTICE Wipe hose ends to remove any dirt before connecting couplers to tractor ports or contamination may cause equipment failure. NOTICE Connect hydraulic motor case drain to a case drain return line with zero PSI on tractor. Failure to connect to a return with zero PSI will cause hydraulic motor shaft seal damage. DO NOT connect hydraulic motor case drain to a SCV outlet or motor return circuit connection. Contact tractor manufacturer for specific details on zero pressure return. NOTICE Always connect hydraulic motor return hose to tractor motor return port. Do not connect to tractor SCV unless through a motor spool or hydraulic motor failure can occur. If a motor return port is not available on the tractor, the SCV controlling the ASD system MUST be in the float position before planter is moved in planting or field raised position when ASD system is not in use. 5. Connect hydraulic hoses to tractor ports in a sequence familiar and comfortable to the operator. Color and Label Machine Function Hose Size Hose Function Red AA Field Lift ½" Pressure Red BB ½" Return Blue AA Planter Fold & Row Marker ⅜" Return Blue BB ⅜" Pressure Green RR EdgeVac Vacuum Fan ¾" Return Green PP ½" Pressure Orange CD ⅜" Case Drain Yellow RR ASD System Pressure Fan ¾" Return Yellow PP ½" Pressure Orange CD ⅜" Case Drain 6 Rev. 0/

15 M0330 Machine Operation NOTICE Clean and grease PTO shaft coupling with highpressure industrial coupling grease (Chevron coupling grease or equivalent) meeting AGMA CG and CG Standards each time driveshaft is installed or premature wear and equipment failure can occur. NOTE: A tractor modelspecific PTO mount kit is required and available from GnL Engineering (3977 or gnlengineering.net) and Rowe Manufacturing (80053 or rowemfg.com). 6. (If applicable) Install PTO pump onto tractor PTO shaft. Make sure shaft rotation matches direction indicated on pump housing. 7. Connect ASABE Standards 7 terminal connector for safety/warning lights on planter to ASABE Standards receptacle on tractor. If your tractor is not equipped with an ASABE Standards receptacle, check with your tractor manufacturer for availability. Check warning lights on planter work in conjunction with warning lights on tractor. NOTE: A volt battery connection is required to power the vacuum fan digital gauge. Connect red wire to positive (+) battery terminal and black wire to negative () battery terminal. Completely raise parking jack to prevent damage to jack assembly and equipment when moving planter. Transporting Planter WARNING Uncontrolled movement of equipment can cause loss of control and could result in death, serious injury, or damage to property and equipment. Install all safety pins before transporting equipment. WARNING Uncontrolled machine movement can crush or cause loss of control resulting in death, serious injury, or damage to property and equipment. Install all safety lockup devices before working under or transporting this equipment. WARNING Transporting planter with hoppers over half full or unevenly loaded can cause loss of control and could result in death, serious injury, or damage to property and equipment. Properly load planter when transporting. Be aware of extra transport weight, and road conditions and limits. Make sure safety/warning lights, reflective decals, and SMV sign are in place and visible before transporting machine on public roads. It is your responsibility to check and comply with all federal, state/provincial, and local regulations. Be aware of road and bridge weight limits. Allow for additional weight of added options and any additional material or substances that have been added to the machine. Rev. 0/ 7

16 Machine Operation M0330 Level Planter Approximately parallel with planting surface Clevis adjustment holes Level row units Toolbar should operate at 0"" height from planting surface. Tire pressures must be maintained at pressures specified for planter to operate level laterally. Check toolbar and row unit parallel arms are level front to back with planter lowered to proper operating height. Five holes in the hitch bracket allow clevis to be raised or lowered. Clevis may be turned over for a finer adjustment between mounting holes. Torque hardware to 80 ftlb (38.8 Nm). Field and actual planting conditions determine which wheel settings to use to ensure row unit parallel arms are approximately parallel with planting surface. If planting in extremely soft soil conditions it may be necessary to move ground drive tires to lower sets of mounting holes. To allow adequate drive force after lowering the ground drive tires, it may be necessary to lower contact drive arms to lower set of holes in wheel module and relocate down pressure springs to lower mounting rod on wheel module. If planter center is higher or lower than wings after rephasing, contact your Kinze Dealer for valve adjustment or maintenance. Contact Wheel Spring Adjustment 8" Spring length measurement (Factory setting) Contact drive springs There are two down pressure springs on each contact drive wheel. Spring tension is factory set to approximately 00 lb (90.7 kg) of down force at tire contact point and should require no further adjustment. NOTE: Measurement must be taken in planting position with proper tire pressure. 8 Rev. 0/

17 M0330 Machine Operation Contact Wheel Drive Sprockets Contact drive wheel sprocket Sprocket idler Contact wheel drive Optional halfrate drive sprocket Contact wheel drive works the same for mechanical or EdgeVac planters except for sprocket size. Chain tension is controlled by a springloaded sprocket idler. Planting rate charts in Rate Chart section help you select correct sprockets. NOTE: Make a field test after each sprocket combination change to be sure you are planting at desired rate. tooth, 8 tooth or tooth sprockets at each contact drive wheel can be exchanged with sprockets on storage rod bolted to wheel module on each side of planter chains. tooth sprockets require 8 pitch No. 0 chains. 8 tooth sprockets require 50 pitch chains. tooth sprockets require use 58 pitch chains. NOTE:, 8 and tooth drive sprockets do NOT apply to all rate charts. Check chart titles to make sure proper rate chart is selected. NOTE: 5 cell sunflower disc uses 5 tooth drive sprocket at contact wheels and 8 tooth drive sprocket at wheel module reverser plates with 9 tooth sprocket. 5 tooth sprockets require pitch No. 0 chains. Applicable sprockets, chains and instructions supplied in GK69 Sunflower Rate Reduction Kit. Seed planting rate charts are based on standard rate drive. Standard rate drive uses a 30 tooth sprocket and No. 0 8 pitch chain on each contact wheel. Optional halfrate ( to ) drive is recommended only when population falls below planting rate charts. Replace 30 tooth sprocket on each contact wheel with a 5 tooth sprocket and shorter No. 0 0 pitch chain. This reduces planter transmission speed and planting and application rates by approximately 50%. Rev. 0/ 9

18 Machine Operation M0330 Seed Rate Transmission Adjustment Planting population rate changes are made using seed rate transmissions at end of each planter wing. Seed rate transmissions allow simple, rapid changes of sprockets by removing lynch pins on hexagon shafts and changing sprockets with those from the sprocket storage rod bolted to transmissions. Chain tension is controlled by a springloaded dual sprocket idler. Idler assembly is adjusted with a easyrelease idler arm with a release position to adjust spring tension for planting or remove spring tension for replacing sprockets. See Wrap Spring Wrench Operation. Drive Driven Seed rate transmission A decal on the transmission (behind chain idler) shows proper chain routing. "Rate Charts" section of this manual will help you select correct sprocket combinations. Wrap Spring Wrench Operation Chain idlers are equipped with wrap spring wrenches. L.H. rotation wrap spring wrenches have a blue release collar and R.H. rotation wrap spring wrenches have a grey or black release collar. Collar Wrap spring wrench (L.H. rotation shown) Chain idler tensioning Rotate collar on wrap spring wrench and pull handle to release chain tension. Rotate chain idler into chain and pull handle to tension idler spring. 0 Rev. 0/

19 M0330 Machine Operation Shear Protection Transmission shaft shear pin Spare shear pin storage Planter driveline and seed and granular chemical drivelines are protected from damage by shear pins. NOTICE Misalignment of drill shaft/transmission coupler alignment will cause equipment damage. Determine where binding has occurred if excessive load causes a pin to shear before replacing pin. Replace shear pins with same size and type. Additional shear pins are in the storage area located at end of each planter wing on inboard side of transport hook. Sliding Hitch Linkage Axle link Draft link Axle link slide (L.H. shown) Row 30" and 36 Row 0" planters are equipped with sliding axle links which connect R.H. and L.H. draft links to transport axle. Axle links move in a slide on inner side of each draft link when planter folds or unfolds. When axle links reach end of slides, main transport axle is telescoped forward into transport position or rearward into field position. NOTICE DO NOT GREASE axle link slides or excess dirt accumulation may cause equipment failure. Inspect daily to ensure free movement of axle links in slides. Keep axle link slides clean. Use only powdered graphite if lubrication is desired. Stops at either end of slides are designed to allow dirt to escape In normal operating conditions. Under extremely dusty conditions it may be necessary to clean slides. Rev. 0/

20 Machine Operation M0330 Hydraulic/Electric Operation Control console switches and tractor s hydraulic system are used to raise planter to transport position, operate rotate and tongue extension functions, lock and release planter wings, and raise and lower row markers. NOTE: Turn console backlighting OFF during extended periods of nonuse using push button switch on back of console. Single point row clutch control box Twospeed point row clutch control box Two dual remote hydraulic outlets (SCV) are required on all sizes of conventional planters equipped with row markers. Three dual remote hydraulic outlets (SCV) are required on all sizes of ASD planters equipped with row markers. One set of outlets is used to operate lift function, one set is used to operate markers, tongue and fold/unfold functions and the third set is used to operate ASD functions (If Applicable). Marker and point row selector switches are an ONOFFON type. If planter is equipped with optional TwoSpeed Point Row Clutch Package, point row switch and reduced rate switch operate independently from rest of control console. Power to marker switch is fed through auxiliary switch and two transport function switches. Operating any lower row switch disables markers and turns off marker indicator light. Raise/wing lock and rotate/tongue (fold function) switches are MOMENTARY ONOFFMOMENTARY ON type and must be held in position while operating tractor hydraulic SCV control. Activating a fold function switch disables marker circuit. WARNING Marker selector switch must be OFF (center position) when not in use to prevent accidental extension which could result in death or serious injury, or damage to property and equipment. An indicator light on control box panel is ON whenever marker circuits or point row clutch circuits are energized. Auxiliary switch is not used. Keep switch OFF at all times. NOTE: Activating auxiliary switch disables all other control console switches except point row clutch switch. Rev. 0/

21 M0330 Machine Operation DIGITAL VACUUM GAUGE Digital vacuum gauge control console is equipped with a power toggle switch, run/stop (fans) toggle switch, and two fan speed control toggle switches for the vacuum fans. Power switch applies power to control console. Run/stop toggle switch turns both fans on when power switch is ON. Fan speed control switches adjusts each fan (left or right). PTO PUMP INITIAL STARTUP Digital vacuum gauge control console. Fill reservoir with SAE 0W0 multigrade wide temperature range transmission hydraulic fluid or equivalent.. Start system. Allow to run with tractor at idle and fans turned off for minutes. 3. Allow to run with tractor at idle and fans at full speed for minutes.. Check fluid level in reservoir and fill as required. NOTE: Fluid level in each tank should be within "" from top of the tank after pump has run and hydraulic hoses are primed to allow fluid to expand when heated. 5. Bring tractor to PTO speed and adjust flow control to desired vacuum level using switches on vacuum fan control console. Row Unit Air Clutches Set Air clutch system pressure to 50 psi. Hall Effect Sensor Set Hall Effect sensor within ⅛" of pickup disc. Air clutch pressure setting Hall effect sensor Pickup disc Hall effect sensor and pickup disc Rev. 0/ 3

22 Machine Operation M0330 Transport to Field Sequence Position planter in a relatively flat open area without furrows, etc. SUMMARIZED TRANSPORT TO FIELD SEQUENCE. Remove hitch parallel linkage lock pin or lockup.. Lower hitch parallel linkage to release wing hooks. NOTICE Unfolding planter without using tractor to assist may cause equipment damage especially in soft conditions or when loaded with seed or fertilizer. Use tractor to reduce stress on frame, drive, and transport components. 3. Place tractor in reverse and hold in clutch. Start unfolding planter and slowly back up tractor as planter unfolds.. Raise planter to remove weight from center (slave) lift cylinder lockups and remove lockups. 5. Lower planter. 6. Remove row marker lockups. 7. Lower catwalk ladder (36 row 0" ASD only) NOTE: Read following information for detailed instructions. WARNING Planter hitch may raise uncontrollably during folding/unfolding and can cause death, serious injury, or damage property and equipment. DO NOT fold or unfold planter without planter attached to a tractor. DO NOT unhitch planter from tractor unless fully folded for transport or fully unfolded with planting units lowered to ground. NOTICE DO NOT LOWER planter frame onto transport axle in folded transport position or transport tires and row units will be damaged. Hitch parallel linkage pin installed Hitch parallel linkage pin stored. Fully extend hitch parallel linkage cylinder located on hitch. Remove hitch parallel linkage lock pin from hitch parallel linkage or cylinder lockup from cylinder rod. Store in location provided. Rev. 0/

23 M0330 Machine Operation Hitch release from wing hook. Hold ROTATE/TONGUE switch in TONGUE position while operating proper tractor hydraulic control to completely retract hitch parallel linkage cylinder and lower hitch until wing wheels are on ground and hitch has released from hooks on ends of wings. Planter unfolding NOTICE Unfolding planter without using tractor to assist may cause equipment damage especially in soft conditions or when loaded with seed or fertilizer. Use tractor to reduce stress on frame, drive, and transport components. 3. Hold control console ROTATE/TONGUE switch in ROTATE and operate hydraulic control to unfold planter. Tongue begins to retract and wings (supported by wing wheels) begin to unfold. Place tractor transmission in a low reverse gear and slowly back up as planter unfolds. Center axle tires should remain stationary and wing tires should roll in a continuous arc with minimal side loading on tires or their mounting structures. Hold switch in ROTATE position until tongue cylinder is fully retracted. Rev. 0/ 5

24 Machine Operation M0330 Safety lockups in transport position Safety lockups in storage position NOTE: Automatic safety lock will release when planter is raised to remove weight from center lift cylinder lockups. Raising planter too high will reset the mechanism. If this happens, lower machine until hydraulic system stalls against the automatic safety, raise machine slightly to release automatic safety lock and then lower planter.. Raise planter to remove weight from center lift (slave) cylinder safety lockups. Remove pins and safety lockups and place in storage location. 5. Lower machine to ground. Center drops until toolbar is level and then entire planter lowers evenly. Hold tractor s hydraulic lever 5 to 0 seconds to rephase system when all lift cylinders are fully retracted. Lowering planter Row marker safety lockup installed Row marker safety lockup stored 6. Remove and store marker lockups. 6 Rev. 0/

25 M0330 Machine Operation Catwalk release lever Catwalk and ladder folded Catwalk and ladder unfolded 7. (36 Row 0" only) Pull on catwalk release lever and swing catwalk extension out until it locks into position. Lift and swing over ladder. Field Operation Planters are designed to operate within a speed range of 8 mph (3 3 kph). Higher ground speeds can cause more variation in seed spacing. Speeds above 5.5 mph (8.8 kph) are typically not recommended. NOTICE: Always raise planter out of ground when making sharp turns or backing up. Normal field planting operation requires use of tractor s hydraulic control to raise and lower planter frame when making field turn arounds. Place hydraulic lever in float position during normal field operation. NOTICE: Operate row markers in float position to prevent damage to row markers. Operate row markers with control console switch for that marker in ON (LEFT or RIGHT) position and tractor s hydraulic control. After markers are lowered to ground, move hydraulic control to operate markers in float position. Marker speed is controlled with flow control valves located in planter hitch valve block. One valve controls raise speed and other valve controls lower speed of both markers. See Row Marker Speed Adjustment and Row Marker Operation. Rev. 0/ 7

26 Machine Operation M0330 Field to Transport Sequence Position planter in a relatively flat open area without furrows, etc. SUMMARIZED TRANSPORT TO FIELD SEQUENCE. Raise and stow catwalk ladder (36 Row 0" ASD only).. Install marker lockups. 3. Raise planter to fully extend master/slave cylinders.. Install center (slave) lift cylinder lockups. 5. Lower planter onto center lift cylinder lockups. NOTICE Folding planter without using tractor to assist may cause equipment damage especially in soft conditions or when loaded with seed or fertilizer. Use tractor to reduce stress on frame, drive, and transport components. 6. Place tractor in low forward gear and hold in clutch. Start folding planter and move tractor slowly forward as planter folds to keep wing wheel side pressure to a minimum. 7. Raise hitch parallel linkage to engage wing hooks. 8. Install hitch parallel linkage lock pin or lockup bracket. 9. Lower hitch parallel linkage cylinder. NOTE: Read following information for detailed instructions. WARNING Planter hitch may raise uncontrollably during folding/unfolding and can cause death, serious injury, or damage property and equipment. DO NOT fold or unfold planter without planter attached to a tractor. DO NOT unhitch planter from tractor unless fully folded for transport or fully unfolded with planting units lowered to ground. Catwalk release lever Catwalk and ladder unfolded Catwalk and ladder folded. (36 Row 0" only) Lift and swing over ladder onto top of catwalk extension. Pull on catwalk release lever and swing extension to stored position until it locks into position. 8 Rev. 0/

27 M0330 Machine Operation Row marker safety lockup stored Row marker safety lockup installed. Install cylinder lockups on marker cylinders to prevent markers from unfolding when not in use or planter is in transport position. Raising planter 3. Hold RAISE/WING LOCK switch on control console in RAISE while operating proper tractor hydraulic control to raise planter. Planter frame should raise level until lift (master) cylinders at ends of wings are fully extended. Center lift (slave) cylinders will continue to extend (at a somewhat slower rate) until they are fully extended. Rev. 0/ 9

28 Machine Operation M0330 Safety lockups in storage position Safety lockups in transport position NOTICE DO NOT fold planter into transport position without lift cylinder lockups installed or uncontrolled planter settling can damage equipment.. Install center (slave) lift cylinder lockups. Install pin assembly to lock each in place. 5. Lower planter onto center lift (slave) cylinder lockups. Planter folding 6. Hold ROTATE/TONGUE switch in ROTATE and operate hydraulic control to fold planter. Slowly idle tractor forward as you fold planter, allowing center axle tires to remain stationary and wing tires to roll in a continuous arc with minimal side loading on tires or their mounting structure. Hooks on wing ends should pass over planter hitch and contact stops on draft links. 0 Rev. 0/

29 M0330 Machine Operation Wing end hook NOTICE DO NOT LOWER planter frame onto transport axle in folded transport position or transport tires and row units will be damaged. 7. Raise hitch parallel linkage to completely engage wing hooks and completely lift wing wheels off ground. Hitch parallel linkage pin stored Hitch parallel linkage pin installed 8. Install parallel linkage lock pin. 9. Lower parallel link cylinder onto lock pin. Rev. 0/

30 Machine Operation M0330 Row Marker Operation DANGER! Contacting or coming close to power lines or other high energy sources will cause death or serious injury. Keep away from power lines or high energy sources at all times. Marker switch Row marker solenoid valves Two solenoid valves on valve block at rear R.H. side of center frame, and a three position selector switch on control console permit operator to lower or raise desired row marker. NOTICE Marker position switch must be OFF when planter is not in use or tractor battery will drain. NOTE: See row marker adjustments on following pages.. Select which row marker to lower on control console.. Operate hydraulic control to lower row marker. 3. Move control switch to other side to operate opposite row marker.. Raise row marker at end of field using hydraulic control. 5. After turn, using the hydraulic control, lower the preselected row marker. 6. Continue to follow this procedure. NOTE: Both row markers can be lowered by operating switch in each position and hydraulic control twice. Row markers raise simultaneously with hydraulic control in raise position. If electrical system does not operate properly: Check fuse. Check wiring connections. Check control switch. Check solenoid. SOLENOID HOUSING IS MAGNETIZED WHEN ENERGIZED. Rev. 0/

31 M0330 Machine Operation Row Marker Speed Adjustment NOTICE Excessive row marker travel speed can damage row markers. Adjust flow controls before row markers are first used. Marker hydraulic system includes two flow control valves. One flow control valve sets lowering speed and one sets raising speed of both markers. Flow controls determine amount of oil flow restriction through valves, varying marker travel speed. Loosen jam nut and turn control clockwise, or IN to slow travel speed. Turn counterclockwise, or OUT to increase travel speed. Tighten jam nut after adjustments are complete. Raise Lower NOTE: Tractors with flow control valves. Make row marker speed adjustment with tractor flow controls in maximum position. After row marker speed is set, adjust tractor flow controls to allow hydraulic control to stay in detent during marker raise or lower cycle. Row marker speed control adjustment NOTE: Hydraulics operate slowly when oil is cold. Make all adjustments with oil warm. NOTE: On a tractor where oil flow cannot be controlled, tractor flow rate may be greater than rate marker cylinder can accept. Hold tractor hydraulic control lever until cylinder reaches end of its stroke. This occurs most often on tractors with an open center hydraulic system. Row Marker Chain Adjustment WARNING Uncontrolled marker movement can cause death or serious injury. set marker switch OFF and shut off tractor prior to adjustment. Chain adjustment is critical. Adjust chain with second stage of marker in vertical position and first stage in horizontal position. Chain must be adjusted so third stage of marker is pulled out as soon as second stage begins outward travel. Chain stretches with use and needs routine adjustment. It may be necessary to twist chain for a finer adjustment. Marker chain is PROPERLY ADJUSTED if marker blade pushes dirt " or less as marker completes fold into field operating position. Chain should have some slack when marker is in field operating position. Marker chain is TOO LOOSE and should be adjusted if marker blade pushes dirt more than " as it completes the fold into field operating position. Marker chain is TOO TIGHT if it will not allow marker blade to follow ground contour and chain is tight when marker is in field operating position. Third stage Second stage Adjust chain First stage Rev. 0/ 3

32 Machine Operation M0330 Row Marker Length And Disc Blade Adjustment. Multiply number of rows by the average row spacing in inches to determine total planting width. Row Marker Lengths Row 0" 80" (,9. cm) Row 30" 70" (,88.8 cm) 36 Row 0" 70" (,88.8 cm). Lower planter and row marker assembly to ground. 3. Measure from planter center line to a point where blade contacts ground.. Adjust row marker extension so distance from marker disc blade to center line of planter is equal to total planting width. Adjust right and left row marker assemblies equally and securely tighten clamping bolts. Loosen hardware to adjust marker length. Loosen hardware to adjust blade angle. Depth band Concave side faces towards planter. Row marker disc blade angle adjustment NOTICE Setting marker disc blade assembly at a sharper angle than needed adds stress to row marker assembly and shortens bearing and blade life. Set blade angle only as needed to leave a clear mark. Marker disc blade is installed with concave side facing inward. Spindle assembly is slotted so hub and blade can be angled to throw more or less dirt. 5. Loosen hardware and move assembly as required. 6. Tighten bolts to specified torque. 7. Do a field test to ensure markers are properly adjusted. NOTE: A notched marker blade is available from Kinze through your Kinze Dealer for use in more severe no till conditions. Rev. 0/

33 M0330 Machine Operation EdgeVac System Kinze EdgeVac seed metering system includes seed meters, seed discs, and an air system consisting of a hydraulic driven vacuum fan which draws air through manifolds, hoses, and seed meters on each row unit. WARNING Moving fan blades can cause amputation or severe injury. Never operate vacuum fan with cover removed. Vacuum Fan Valve Block Assembly A pressure relief valve prevents build up of oil pressure over 35 PSI in case drain line when vacuum fan motor is operating. This valve vent oils outside through a drain hole in aluminum valve block. This can occur whenever case drain is improperly connected or pressure in motor circuit builds. Valve block contains a check valve that prevents vacuum fan from operating in wrong direction if pressure is applied to return side of motor and allows fan to coast to a stop when tractor hydraulic control is returned to neutral position. Vacuum fan valve block See Hydraulic Schematic (Vacuum Fan System)" in Lubrication and Maintenance section. NOTE: Fan turns at a reduced speed If reverse pressure is applied. Analog Vacuum or Pressure Gauge Analog vacuum or pressure gauge connects directly to EdgeVac (vacuum) or ASD (pressure) manifold and is teed into digital sending units. Only adjustment is to zero needle with no vacuum or pressure present. If there is a significant difference between gauge and a reading taken at meters, a different manifold location should be found to connect hose to gauge and digital sending unit. Analog gauge NOTE: Analog gauges are identical EXCEPT for plug and hose barb locations in side of gauge housing. DO NOT connect EdgeVac or ASD hose to wrong gauge. Check plug and hose barb installation if readout is erratic or appears inaccurate. Rev. 0/ 5

34 Machine Operation M0330 Kinze Cobalt System The Cobalt electronic seed monitor system consists of a tractormounted console, seed tubes with computerized sensors installed in each planter row unit, a primary harness connecting console to planter harness, and a planter harness (junction Yharness and/or harness extension where applicable), connected to each seed tube sensor. Cobalt monitor is built to withstand harsh environments associated with today s agricultural industry. The weathertight enclosure seals out dirt and moisture encountered during normal operating conditions This system is compatible with all Kinze planters, and can be transferred between multiple vehicles to maximize return on investment. Kinze Cobalt display The Cobalt system allows manual control of air clutches and variable population control when planter is equipped with these options. It is not GPS compatible. NOTE: See Kinze Cobalt Operator Manual for installation and programming. Ag Leader Integra Display Integra is a fullfeatured hub of any precision farming operation. A large, fullcolor." HD touchscreen display is easy to read and offers powerful, yearround precision farming tools. Mapping, planter and application control, yield monitoring, realtime data logging, and more are all controlled from the cab using the Integra display. Four video camera inputs provide operators a better view of equipment operation and safety by allowing them to view live video on the display. NOTE: See Integra Operator Manual for installation and programming. Ag Leader Integra display Planter Monitor Module (PMM) PMM Magnetic Distance Sensor Package includes a plantermounted module enclosure with cover and mounting hardware, seed tubes w/sensors, planter harness, planter monitor cable, shaft rotation sensors and magnetic distance sensor components. PMM Ag Leader Integra display and associated cab harnesses are also required. Cover (removed) Planter Monitor Module (PMM) 30 Rev. 0/

35 M0330 Machine Operation Point Row Clutches L.H. point row clutch switch 0 amp time delay fuse R.H. point row clutch switch 0 amp time delay fuse Point row clutch switch Single point row clutch control box Point row clutch Electricactivated clutches disengage drive on either half of planter for finishing up fields or for long point row situations. Clutch selector switch is located on tractor control box. NOTICE Switch must be OFF when planter is not in use or tractor battery will be drained. NOTE: Liquid fertilizer piston pump has its own drive wheel and is not affected by point row clutch. Stop collar Output hub Wrap spring Input hub Control tang Clutch consists of a wrap spring riding on an input and output hub. Wrap spring is wrapped tightly over hubs during operation locking them together. Higher speeds create a tighter grip of spring on hubs. Input end of spring is bent outward and is called the control tang. Control tang fits into a slot in stop collar located between input and output hubs over wrap spring. If stop collar is allowed to rotate with input hub, clutch is engaged. If stop collar is stopped from rotating, control tang connected to it is forced back and spring opens. This allows input hub to continue rotating without transmitting torque to output hub, stopping planter drive. Stop collar is controlled by an electric solenoid and an actuator arm. When selector switch on tractor control box is OFF, solenoid coil is NOT ENERGIZED and actuator arm will not contact stop on stop collar, allowing it to rotate with hubs and drive planter. When operational switch is in DISENGAGE (right or left) solenoid coil IS ENERGIZED and plunger in solenoid coil pulls actuator arm against stop on stop collar, disengaging wrap spring and stopping planter drive. Rev. 0/ 3

36 Machine Operation M0330 TwoSpeed Point Row Clutches Drive sprocket Twospeed clutch Decal Input from contact drive wheel Twospeed point row clutch Driven sprocket (30 tooth overunning) Twospeed point row clutch driven sprockets Optional TwoSpeed Point Row Clutch Package allows onthego population rate adjustment and capability to shut off either half of planter for finishing up fields or for long point row situations. Population reduction ratio is determined by sprocket ratio between wheel module extension drive and driven sprockets. A rate reduction decal is located on wheel module extension. Reduced rate indicator L.H point row clutch indicator R.H point row clutch indicator Point row clutch rate switch Point row clutch selector switch Twospeed point row clutch control box Point row clutches are controlled by control console point row clutch switches. The point row switch shuts off left or right half of planter. Activating reduced rate switch engages one solenoid on each clutch assembly and reduces planting rate for entire planter. NOTICE Point row switch must be OFF and rate switch left in FULL RATE when planter is not in use or tractor battery will be drained. NOTE: Liquid fertilizer piston pump has its own drive wheel and is not affected by point row clutch. 3 Rev. 0/

37 M0330 Machine Operation Piston Pump NOTE: Keep manuals shipped with pump and flow divider with this manual. Piston pump Adjusting delivery rate NOTE: Delivery rate chart in Rate Chart section of this manual provides approximate application rate only. Delivery varies with temperature and fertilizer. Loosen ⅜" lock nut that secures arm with pointer and rotate scale flange with adjustment wrench until pointer is over desired scale setting. Tighten ⅜" lock nut. DO NOT OVERTIGHTEN. NOTE: Periodically check flow to all rows. Set rate is delivered to remaining rows if one or more lines are plugged. Spring tension adjustment Contact tire bracket Contact tire Mounting bracket stop Transport tire Set piston pump drive spring tension so there is no slack in springs when contact tire bracket is resting on mounting bracket stop. Contact tire and transport tire should not be touching. CLEANING Clean tanks, hoses, and metering pump thoroughly with water at end of planting season or prior to an extended period of nonuse. Do not allow fertilizer to crystallize from cold temperature or evaporation. Screen On machines equipped with piston pump, take apart and clean strainer located between piston pump and ball valve daily. Remove the end cap to clean the screen. See Piston Pump Storage in Maintenance Section of this manual. End cap Rev. 0/ 33

38 Machine Operation M0330 Check Valves Old style nonreparable check valve New style reparable check valve Optional low rate check valves are available for inline installation between liquid fertilizer piston pump and openers to ensure equal distribution of product at low rates. Check valves eliminate antisiphon loops. Rear Trailer Hitch ( Row 30" Only) Trailer hitch Hitch position during lift Rear trailer hitch is used to tow a 3 or wheel wagon behind planter. Hitch height during field operation and transport is 5". Hitch height will raise to approximately " when planter is lifted. NOTICE Rear trailer hitch is designed for use with piston pump only. Maximum allowable hitch weight is 00 lb (90.7 kg). Do not exceed 6,000 lb (,7.55 kg) gross towing weight or the equivalent of a loaded 500 gal (,89.7 L) tank and running gear or equipment can be damaged. NOTE: Periodically check feed hose for kinks to prevent restricted delivery rate. Adjust rear trailer hitch length by loosening the ⅝" set screws at rear of outer tube, removing " x 8 ½" bolt at center of hitch, and sliding hitch in or out to one of sets of adjustment holes. Reinstall and tighten hardware. 3 Rev. 0/

39 M0330 Machine Operation Field Test Perform a field test with any change of field and/or planting conditions, seed size or planter adjustment to ensure proper seed placement and operation of row units. Check planter for front to rear and lateral level operation. See Level Planter. Check all row units to be certain they are running level. Row unit parallel arms should be approximately parallel to the ground when planting. Check row markers for proper operation and adjustment. See Row Marker Speed Adjustment, "Row Marker Chain Adjustment", and Row Marker Length and Disc Blade Adjustment. Check for proper application rates and placement of granular chemicals on all rows. See Field Check Granular Chemical Application. Check for desired depth placement and seed population on all rows. See Field Check Seed Population. Check for proper application rates of fertilizer on all rows. See Fertilizer Application Rate Chart. Reinspect machine after field testing. Hoses And Fittings Bolts And Nuts Cotter Pins And Spring Pins Drive Chain Alignment Field Check Seed Population Chain, rubber tarp strap, or similar.. Tie up one or more sets of closing wheels by running a chain or rubber tarp strap between the hopper support panel and closing wheels. It may be necessary to decrease closing wheel arm spring tension. Planting depth adjustment handle. Plant a short distance and check to see if seed is visible in the seed trench. Adjust planting depth to a shallower setting if seed is not visible and recheck. Deeper Shallower Planting depth adjustment Rev. 0/ 35

40 Machine Operation M Measure 000 of an acre. See chart for correct distance for row width being planted. For example, if planting 30" rows 000 of an acre would be 7' 5". NOTE: Seeds may bounce or roll when planting with closing wheels raised and planting depth set shallow affecting seed spacing accuracy.. Count seeds in measured distance. 000 Acre Seed Population Count Row Width/Distance Row Width 0" 30" Distance 6'" 7'5" 5. Multiply number of seeds placed in 000 of an acre by 000. This gives total population. EXAMPLE: 30" row spacing 7' 5" equals 000 acre. 6 seeds counted x 000 = 6,000 seeds per acre Seed count can be affected by drive wheel and seed meter drive ratio, tire pressure, and/or seed meter malfunction.. If seed check shows average distance between seeds in inches is significantly different than seed rate chart indicates, first check drive ratio between drive wheel and seed meter. Check drive wheel air pressure, check for incorrect sprocket(s) in driveline and check drive and driven sprockets on transmission(s) for proper selection.. Check for seed meter malfunction. For example, if spacing between kernels of corn at the transmission setting being used is 8" and a gap of 6" is observed, a finger has lost its seed and not functioned properly. If two seeds are found within a short distance of each other, finger has metered two seeds instead of one. 3. See Seed Meter (Finger Pickup) Troubleshooting or Seed Meter (BrushType) Troubleshooting in Troubleshooting Section of this manual. Determining Pounds Per Acre (BrushType Meter) Seeds per acre Seeds per pound (from label) = Pounds per acre If seeds per pound information is not available use the following averages:,600 seeds per pound for medium size soybeans 5,000 seeds per pound for medium size milo/grain sorghum,500 seeds per pound for medium size cotton Determining Bushels Per Acre Pounds per acre Seed unit weight = Bushels per acre Average Unit Weight of: Bushel Soybeans = 60 Pounds Bushel Milo/Grain Sorghum = 56 Pounds Bushel Cotton = 3 Pounds If seed population check shows planting rate is significantly different than seed rate chart shows or if a particular meter is not planting accurately, see BrushType Seed Meter Maintenance and Seed Meter (BrushType) Troubleshooting. 36 Rev. 0/

41 M0330 Machine Operation Field Check Granular Chemical Application Temperature, humidity, speed, ground conditions, flowability of different material, or meter obstructions can affect granular chemical rate of delivery. WARNING Agricultural chemicals can cause death or serious injury to persons, animals, and plants or seriously damage soil, equipment, or property. Read and follow all chemical and equipment manufacturers labels and instructions. Perform a field check to determine application rates. Calibrated vial Granular chemical field check. Fill insecticide and/or herbicide hoppers.. Attach a calibrated vial to each granular chemical meter. NOTE: Disengage clutch to avoid dropping seed during test. 3. Lower planter and drive 30 feet at planting speed.. Weigh chemical in ounces caught in one vial. 5. Multiply that amount by factor shown to determine pounds per acre. EXAMPLE: You are planting 30" rows. You have planted for 30 feet at desired planting speed. You caught.0 ounces of chemical in one vial..0 ounces times 0.83 equals 9.96 pounds per acre. NOTE: Check calibration of all rows. METERING GATE Pounds Per Acre Row Width Factor 0".5 30".83 Use metering gate setting as a starting point for distributing insecticide or herbicide. Charts are based on 5 mph (8 kph) planting speed. Use a higher gate setting for speeds faster than 5 mph (8 kph) and a lower setting for speeds slower than 5 mph (8 kph). Rev. 0/ 37

42 This page intentionally left blank.

43 M0330 Rate Charts General Planting Rate Information These planting rate charts apply to KINZE planters. NOTICE Sprocket combinations in these charts are for average conditions. Changes in sprocket combinations may be required for desired planting population. ALWAYS MAKE FIELD CHECKS to BE SURE YOU ARE PLANTING AT DESIRED RATE. NOTICE Seed additives added in the hopper may affect finger pickup seed meter performance and accelerate wear. NOTE: Seed size and shape may affect planting rate. note: Not all row spacings listed apply to all size planters. note: Speeds above 5.5 MPH (8.8 KPH) can adversely affect seed spacing. Mechanical Finger Pickup Corn Meter Larger grades generally plant more accurately at the high end of the ground speed range than smaller grades. Higher than optimum speeds may result in population rate increase or higher incidence of doubles, particularly with small seed. Medium round corn seed is most desirable for planting accuracy at optimum speed. Finger Pickup Oil Sunflower Meter Larger grades generally plant more accurately at the high end of the ground speed range than smaller grades. Higher than optimum speeds may result in population rate increase or higher incidence of doubles, particularly with small seed. No. 3 and/or No. size oil sunflower seeds are recommended for use in finger pickup seed meters equipped with oil sunflower fingers. No. and/or No. size confectionery sunflower seeds are recommended for use in finger pickup seed meters equipped with corn fingers. BrushType Seed Meter (Soybean, Milo/Grain Sorghum, AcidDelinted Cotton) Rate charts are given in seeds per acre as well as seed spacing in inches rounded to nearest tenth of an inch. Because of large range in seed size, pounds per acre is not a suggested method of selecting transmission settings. Smaller size seed pounds per acre may be below what was expected and large seed pounds per acre may appear above expectations. To determine pounds per acre, use formula given in Determining Pounds Per Acre (BrushType Seed Meter) in Check Seed Population in Machine Operation section of this manual. NOTE: Planting speed can affect actual seeding rate. Make a field check and adjust transmission setting to obtain desired seed drop. note: Seed population per acre with 5" rows double rate for 30" rows, as well as 8" rows versus 36" rows and 9" rows versus 38" rows, at listed sprocket combination. See following pages. note: Half Rate ( to ) Drive Reduction Package may be required to obtain desired population and seed spacing when planting 5" row soybeans or other crops. Half Rate Drive with brushtype seed meters reduces planter transmission speed. Seeding rate will be approximately 50% of chart reading when using Half Rate ( To ) Drive Reduction Package. EdgeVac EXAMPLE: 30" row spacing using 60 cell seed discs in brushtype seed meters. 80,98 = 0,6 Population (.6" Seed Spacing x = 5." Seed Spacing) note:, 8 and tooth drive sprockets are NOT applicable to all rate charts. Check chart titles to ensure proper rate chart is selected. tooth sprockets require use of 8 pitch No. 0 chains, 8 tooth sprockets require use of 50 pitch No. 0 chains and tooth sprockets require use of 58 pitch No. 0 chains. note: When using 5 cell sunflower disc, use 5 tooth drive sprocket at contact wheels and replace 8 tooth drive sprocket at wheel module reverser plates with 9 tooth sprocket. 5 tooth sprockets require use of pitch No. 0 chains. Applicable sprockets, chains, and instructions supplied in GK69 Sunflower Rate Reduction Kit. Rev. 0/

44 Rate Charts M0330 PLANTING RATES FOR FINGER PICKUP SEED METERS (STANDARD DRIVE) APPROXIMATE SEEDS/ACRE FOR VARIOUS ROW WIDTHS 0" 30" Transmission Sprockets Recommended Rows Rows Drive Driven Speed Range (MPH),79 6, to 6.9 5,78 6, to 6.5 6,7 7,3 7 6 to 6.0 7,35 8, to 6.6 7,9 8,8 7 5 to 6.5 8,0 8, to 6. 8,35 8,883 7 to 6. 9, 9,8 9 6 to ,556 9, to ,39 0,6 9 5 to ,656,0 9 to ,87, to ,033,0 9 3 to ,06, to ,75,850 8 to ,375 3, to ,56 3,697 7 to ,703 3, to ,780 3, to ,789, to ,9,608 6 to ,06, to ,33, to ,3 5,58 3 to ,388 5,59 5 to ,50 5, to ,507 5, to ,56 5, to ,989 6, to 6 7.8,69 7, to 6 7.6,56 7, to 6 7.6,655 7,770 5 to 6 7.5,77 7,88 3 to ,06 8, to ,87 8, to ,66 8, to 6 7.,693 9, to 6 7.0,787 9, to 6 7.0,987 9,99 7 to ,0 30, to ,653 3,0 8 3 to ,93 3, to ,07 3, to ,68 3, to ,5 33, to ,66 35, to ,0 36, to ,70 36, to ,5 37, to ,85 37, to ,806 39, to ,93 39, to ,58 0, to ,50, to ,86 3, to.5.8 NOTE: See General Planting Rate Information and Check Seed Population pages for more information. Always field check seed population to verify planting rates. Average Seed Spacing In Inches Rev. 0/

45 M0330 Rate Charts Transmission Sprockets Drive PLANTING RATES FOR BRUSHTYPE SEED METERS (STANDARD DRIVE) APPROXIMATE SEEDS/ACRE FOR VARIOUS ROW WIDTHS 60 Cell Soybean Or Average 8 Cell Specialty Average HighRate Milo/Grain Seed Soybean Or HighRate Seed Sorghum Spacing In AcidDelinted Cotton Spacing In Driven Inches Inches Speed Range (MPH) 0" Rows 30" Rows 0" Rows 30" Rows 7 8,39 80, ,3 6,7 3. to ,889 83, ,7 67, 3. to ,73 87,5. 0,7 69, to ,67 90,9.3 08,539 7,359.9 to ,699 93,799.,559 75,039.8 to 8 7,6 9,6. 3,300 75,533.8 to ,78 98,5. 8,6 78,87.7 to ,955 0,303.,563 8,0.6 to ,86 05,5.0 6,69 8,9.5 to ,37 09,9.9 3,390 87,593. to ,68 0,.9 3,35 88,090. to 8 8 7,379,5.8 37,03 9,0.3 to ,75 8,83.8,79 9,786. to ,895 9,63.8 3,5 95,0. to 8 6 8,560 3,00.7 7,68 98,3. to ,660 3, ,57 99,08. to 8 5 9,93 7, ,555.0 to ,536 8, ,09.0 to ,9 33,9.6 59,953.0 to ,630 38,0.5 66,0.9 to ,63 39, ,907.9 to ,36,88. 73,86.8 to ,63 8, ,770.8 to 8 7,933 9, ,96.7 to ,6 55, ,66.7 to 8 3 9,033 6, ,66.6 to ,05 6,70.3 9,7.6 to 8 9 5,557 68,37. 0,0.6 to ,079 75,386. 0,6.5 to ,507 80,338. 6,05.5 to ,603 8,0. 8,883. to ,6 89,7. 7,30. to ,650 96,33. 35,79.3 to ,79 03,86.0,63.3 to ,553, ,03. to ,33 9, ,5. to 7 note: See General Planting Rate Information and Check Seed Population pages for additional information. note: When using Half Rate ( To ) Drive Reduction Package, rates are approximately 50% of given numbers. note: Always field check seed population to ensure planting rates are correct. Rev. 0/ 3

46 Rate Charts M0330 PLANTING RATES FOR BRUSHTYPE SEED METERS (STANDARD DRIVE) APPROXIMATE SEEDS/ACRE FOR VARIOUS ROW WIDTHS 36 Cell AcidDelinted 30 Cell Milo/Grain Large Cotton Sorghum Or Acid Transmission Sprockets Average Seed Spacing In Inches Average Seed Spacing In Inches Speed Range (MPH) Drive Driven Delinted Cotton 0" Rows 30" Rows 0" Rows 30" Rows 7 8 7,836 8, ,696 0,6 5. to ,53 50,356. 6,95, to ,38 5,9.0 65,366 3,577.8 to ,0 5, ,838 5,5.6 to ,9 56, ,350 6,900.5 to 8 7 8,975 56, ,8 7,08. to ,670 59, ,89 9,6. to ,73 60, ,978 50,65. to 8 9 9,97 63, ,3 5,76.0 to ,53 65, ,9 5, to ,0 66, ,58 55, to 8 8 0,87 68, ,689 57,6 3.7 to ,635 7, ,863 59, 3.5 to ,337 7, ,7 59, to 8 6 0,736 73,8.8 9,80 6,50 3. to 8 6 8,396 7,6.8 9,89 6, to 8 5 5,58 76, ,97 63, to ,5 77,0.7 96,67 6, to ,96 79, ,97 66,67 3. to 8 7 6,578 83, ,85 69,0 3.0 to 8 3 5,80 83,53.5 0,36 69,5 3.0 to ,395 86, ,663 7,.9 to ,078 89,385.3,73 7,88.8 to 8 7 3,960 89,973.3,67 7,978.8 to ,958 93,305. 6,633 77,755.7 to ,0 96,83.,07 80,678.6 to ,03 97,36.,703 8,35.6 to 8 9 5,535 0,03. 6,78 8,85.5 to ,88 05,3.0 3,50 87,693. to ,350 08, ,5 90,69.3 to ,6 09,.9 36,80 9,0.3 to ,75 3,650.8,06 9,709. to ,790 7, ,3 98,6. to ,76,37.7 5,895 0,930. to ,53 7,0.6 58,777 05,85.0 to ,588 3,75.6 6,657 09,77.9 to 7 note: See General Planting Rate Information and Check Seed Population pages for additional information. note: When using Half Rate ( To ) Drive Reduction Package, rates are approximately 50% of given numbers. note: Always field check seed population to ensure planting rates are correct. Rev. 0/

47 M0330 Rate Charts PLANTING RATES FOR BRUSHTYPE SEED METERS (STANDARD DRIVE) APPROXIMATE HILLS/ACRE FOR VARIOUS ROW WIDTHS Due to variations in cotton seed size, meters equipped with the cell aciddelinted hilldrop cotton discs will plant from 3 to 6 seeds per cell. Select proper disc for seed size range to be planted. To determine planter transmission setting, determine desired hill spacing and select the transmission ratio closest to the hill spacing in inches on the chart. To decrease population increase spacing. To increase population decrease spacing. To determine population per acre, determine average seeds per hill and hills per acre by doing a field check. Measure 000 of an acre ( 000 acre = Length of row 7' 5" for 30" row width, 3' 9" for " row width and 6' " for 0" row width). Multiply average seeds per hill by hills per acre. EXAMPLE: seeds per hill x (3 hills x 000) = 5,000 Transmission Sprockets NUMBER OF HILLS PER ACRE Cell HillDrop Cotton, AcidDelinted Average Hill Spacing In Inches Speed Range (MPH) Drive Drive 0" Rows 30" Rows 7 8,79 6,86.9 to ,78 6,785.5 to ,7 7,3.0 to ,35 8,090.6 to ,0 8,760. to 8 7 8,35 8,883. to ,556 9, to ,39 0,6 0.3 to 8 9 3,658, to ,87, to ,033,0 9.5 to 8 8 3,75, to ,56 3, to ,780 3, to ,9, to ,33, to ,388 5,59 8. to ,507 5,67 8. to ,989 6, to 8 7 6,56 7, to 8 3,77 7, to ,66 8, to 8 9 7,693 9, to 8 7,987 9, to 8 8 6,653 3,0 6.7 to ,07 3,7 6.5 to ,68 3,5 6.5 to ,5 33,67 6. to ,66 35, to ,0 36, to ,70 36, to ,85 37, to ,93 39, to ,58 0,77 5. to ,50,30.9 to ,86 3,908.8 to 7 note: See General Planting Rate Information and Check Seed Population pages for additional information. note: When using Half Rate ( To ) Drive Reduction Package, rates are approximately 50% of given numbers. note: Always field check seed population to ensure planting rates are correct. Rev. 0/ 5

48 Rate Charts M0330 Edgevac Planting Rates for Corn / Popcorn 39 Cell Disc tooth CONTACT WHEEL DRIVE SPROCKET APPROXIMATE SEEDS / ACRE FOR VARIOUS ROW WIDTHS 30" Rows Transmission Sprockets Recomm. Speed Average Seed Spacing Drive Driven Range (MPH) In Inches 3, to 6 9.0, to 6 8.7, to , to , to ,077 5 to , to ,5 5 3 to , to , to , to , to ,687 7 to , to ,0 7 3 to , to ,0 5 9 to ,97 9 to , to , to , to ,3 8 to ,6 5 7 to ,509 7 to , to , to ,8 6 8 to 6 5.,58 3 to 6 5.0,590 5 to 6 5.0, to , to 6.8, to 6.7, to 6.6 5,06 3 to 6.6 6, to 6.5 6, to 6.5 7, to 6. 8,0 9 7 to 6.3 8,738 7 to 6.3 8, to ,53 8 to 6. 50, to 6. 5,3 3 9 to 6.0 5,7 8 3 to 6.0 5,7 9 to , to , to ,8 6 9 to ,6 7 to , to , to ,8 8 9 to , to ,8 3 5 to , to NOTE: See General Planting Rate Information and Check Seed Population pages for more information. Always field check seed population to verify planting rates. 6 Rev. 0/

49 M0330 Rate Charts Edgevac PLANTING RATES FOR CORN / POPCORN 39 CELL DISC 8 tooth CONTACT WHEEL DRIVE SPROCKET APPROXIMATE SEEDS / ACRE FOR VARIOUS ROW WIDTHS 30" Rows Transmission Sprockets Drive Driven Recomm. Speed Range (MPH) Average Seed Spacing In Inches 9, to , to , to , to , to ,6 5 to , to , to , to ,5 9 8 to ,9 7 5 to , to ,056 7 to , to , to 6 5., to , to 6.8 3,65 9 to 6.8 5,9 3 8 to 6.6 5, to 6.6 6, to 6.5 7,6 8 to 6. 8, to 6.3 9,0 7 to 6.3 9, to 6. 50, to 6. 5, to 6. 5,8 3 to 6.0 5,933 5 to , to , to , to , to ,535 3 to , to , to , to , to ,030 7 to , to ,38 8 to , to , to ,5 8 3 to ,68 9 to , to 6.9 7, to ,5 6 9 to ,8 7 to , to 6.7 8, to 6.6 8, to 6.6 8, to 6.5 8, to , to 6. NOTE: See General Planting Rate Information and Check Seed Population pages for more information. Always field check seed population to verify planting rates. Rev. 0/ 7

50 Rate Charts M0330 Edgevac Planting Rates for LowRate Corn / Popcorn Cell Disc tooth CONTACT WHEEL DRIVE SPROCKET APPROXIMATE SEEDS / ACRE FOR VARIOUS ROW WIDTHS 30" Rows Transmission Sprockets Drive Driven Recomm. Speed Range (MPH) Average Seed Spacing In Inches,8 5 8 to 6.6,8 5 7 to 6. 5, to , to , to 6.9 6,663 5 to 6.5 6, to 6.5 7, to 6.0 7,3 7 6 to 6.0 8, to 6.6 8,9 7 5 to 6.5 8, to 6. 8,88 7 to 6. 9,8 9 6 to , to ,6 9 5 to 6 0.3, to 6 9.9,06 9 to 6 9.9, to 6 9.5,0 9 3 to 6 9.5,7 3 7 to 6 9.,85 8 to ,5 5 7 to ,698 7 to , to 6 8.8, to 6 8.5, to ,59 3 to ,59 5 to , to , to , to , to ,89 3 to ,7 8 6 to , to , to , to ,993 7 to , to ,0 8 to , to , to , to ,676 9 to , to , to ,8 6 9 to ,638 7 to , to , to , to , to , to 6 5., to 6.9 NOTE: See General Planting Rate Information and Check Seed Population pages for more information. Always field check seed population to verify planting rates. 8 Rev. 0/

51 M0330 Rate Charts Edgevac PLANTING RATES FOR LOWRATE CORN / POPCORN CELL DISC 8 tooth CONTACT WHEEL DRIVE SPROCKET APPROXIMATE HILLS / ACRE FOR VARIOUS ROW WIDTHS 30" Rows Transmission Sprockets Recomm. Speed Average Seed Spacing Drive Driven Range (MPH) In Inches 8, to 6.6 8, to 6. 9,8 5 6 to , to , to 6 0.,0 5 to 6 9.9,6 7 7 to 6 9.8,0 5 3 to 6 9.5, to 6 9.5, to 6 9., to , to ,98 7 to 6 8.7, to 6 8.5, to , to , to ,73 9 to , to , to , to ,93 8 to , to ,05 7 to , 7 9 to , to , to ,360 3 to ,6 5 to , to , to , to , to ,35 3 to , to , to , to , to ,988 7 to ,7 6 3 to ,39 8 to , to , to 6 5., to 6 5.,653 9 to 6.9, to 6.7 5, to 6.6 6, to 6.5 7,67 7 to 6. 7, to 6. 9, to 6. 9, to 6. 5, to 6.0 5, to , to NOTE: See General Planting Rate Information and Check Seed Population pages for more information. Always field check seed population to verify planting rates. Rev. 0/ 9

52 Rate Charts M0330 Edgevac Planting Rates for Soybean and Milo / Grain Sorghum 60 Cell Discs tooth CONTACT WHEEL DRIVE SPROCKET APPROXIMATE SEEDS / ACRE FOR VARIOUS ROW WIDTHS 30" Rows Transmission Sprockets Recomm. Speed Average Seed Spacing Drive Driven Range (MPH) In Inches 35, to , to ,5 5 6 to , to , to 6 5.,657 5 to 6 5.0, to , to 6.8 3, to 6.8 5,7 9 8 to 6.6 5,3 7 5 to 6.6 6, to 6.5 7, 7 to 6. 8, to 6.3 9, to 6. 50, to 6. 5, to 6.0 5,765 9 to 6.0 5, to , to , to ,9 8 to , to ,5 7 to , to , to , to ,873 3 to ,985 5 to , to , to ,9 8 7 to , 7 6 to ,58 3 to , to 6.9 7, to 6.9 7,6 5 3 to 6.9 7,9 9 7 to 6.8 7,98 7 to ,3 6 3 to ,759 8 to , 7 3 to , to 6.6 8,0 8 3 to 6.6 8,90 9 to , to 6. 90,7 3 7 to 6.3 9, to 6.3 9,095 7 to 6. 9,7 7 9 to 6. 98, to 6. 98, 8 9 to 6. 0, to 6. 0, to , to 6.0 NOTE: See General Planting Rate Information and Check Seed Population pages for more information. Always field check seed population to verify planting rates. 0 Rev. 0/

53 M0330 Rate Charts Edgevac PLANTING RATES FOR SOYBEAN AND MILO / GRAIN SORGHUM 60 CELL DISCS 8 tooth CONTACT WHEEL DRIVE SPROCKET APPROXIMATE SEEDS / ACRE FOR VARIOUS ROW WIDTHS 30" Rows Transmission Sprockets Recomm. Speed Average Seed Spacing Drive Driven Range (MPH) In Inches 5, 5 8 to 6.6 7,7 5 7 to 6. 8, to , to 6. 5, to 6. 53,07 5 to ,0 7 7 to , to ,6 7 6 to , to , to , to ,086 7 to , to , to , to , to ,55 9 to , to , to ,6 3 7 to 6.9 7,70 8 to 6.9 7, to ,03 7 to , to ,0 3 5 to , to 6.7 8,93 3 to 6.6 8,35 5 to 6.6 8, to 6.6 8, to , to 6. 88, to 6. 88,56 3 to 6. 9, to 6.3 9,6 7 5 to 6.3 9,0 5 3 to 6.3 9, to 6. 95,3 7 to 6. 95, to 6. 98,966 8 to 6. 99, to 6. 0, to , to ,5 9 to 6.0, to 6.9, to 6.8 6, to 6.8 9,757 7 to 6.7 0, to 6.7, to 6.7 5, to 6.7 9, to , to 6.6 3, to 6.6 NOTE: See General Planting Rate Information and Check Seed Population pages for more information. Always field check seed population to verify planting rates. Rev. 0/

54 Rate Charts M0330 Edgevac Planting Rates for Soybean 60 Cell Disc tooth CONTACT WHEEL DRIVE SPROCKET APPROXIMATE SEEDS / ACRE FOR VARIOUS ROW WIDTHS 30" Rows Transmission Sprockets Recomm. Speed Average Seed Spacing Drive Driven Range (MPH) In Inches 7, to 6.9 7, to , to , to , to ,308 5 to , to , to 6. 87, to 6. 90,8 9 8 to , to , to 6. 9,5 7 to 6. 97, to 6. 98, to 6. 0, to 6. 05,3 5 9 to ,53 9 to , to 6.9 0, 9 3 to 6.9 3, to 6.8,50 8 to 6.8 7,6 5 7 to 6.8 8,8 7 to 6.8 9,6 7 9 to 6.8, to 6.7 3, to 6.7 7,738 3 to 6.6 7,960 5 to 6.6 8, to ,9 3 3 to ,9 8 7 to ,9 7 6 to ,087 3 to 6.5 3, to 6.5 3, to 6.5, to 6. 8, to 6. 9,95 7 to 6. 50, to 6. 55,507 8 to , to 6.3 6, to 6.3 6, to ,369 9 to 6. 75, to 6. 80, to 6. 8, to 6. 88,77 7 to 6. 89,5 7 9 to 6. 96, to 6. 96, to 6. 03, to 6.0 0, to 6.0, to 6.0 NOTE: See General Planting Rate Information and Check Seed Population pages for more information. Always field check seed population to verify planting rates. Rev. 0/

55 M0330 Rate Charts Edgevac Planting Rates for HighRate Soybean 0 Cell Disc tooth CONTACT WHEEL DRIVE SPROCKET APPROXIMATE SEEDS / ACRE FOR VARIOUS ROW WIDTHS 30" Rows Transmission Sprockets Recomm. Speed Average Seed Spacing Drive Driven Range (MPH) In Inches 7, 5 8 to 6.9 7, to , to , to , to ,33 5 to , to , to 6. 87, to 6. 90,5 9 8 to , to , to 6. 9, 7 to 6. 97, 9 6 to 6. 98, to 6. 0, to 6. 05, to ,530 9 to , to 6.9 0,8 9 3 to 6.9 3, to 6.8,58 8 to 6.8 7, to 6.8 8,90 7 to 6.8 9, to 6.8, to 6.7 3, to 6.7 7,77 3 to 6.6 7,969 5 to 6.6 8, to , to , to ,8 7 6 to ,097 3 to 6.5 3, to 6.5 3, to 6.5, to 6. 8, to 6. 9,96 7 to 6. 50, to 6. 55,58 8 to ,8 7 3 to 6.3 6, to 6.3 6, to ,380 9 to 6. 75, to 6. 80, to 6. 8, 6 9 to 6. 88,90 7 to 6. 89,8 7 9 to 6. 96, to 6. 96, 8 9 to 6. 03, to 6.0 0, to 6.0, to 6.0 NOTE: See General Planting Rate Information and Check Seed Population pages for more information. Always field check seed population to verify planting rates. Rev. 0/ 3

56 Rate Charts M " Rows Transmission Sprockets Recomm. Speed Average Seed Spacing Drive Driven Range (MPH) In Inches 90, to 6.3 9, to 6. 97, to 6. 0, to 6. 03, to ,035 5 to , to 6.0 0, to 6.9 0, to 6.9 5, 9 8 to 6.8 5, to 6.8 9, to 6.8 0,73 7 to 6.7 3, to 6.7 5, to 6.7 8, to , to 6.6 3,3 9 to , to 6.5 0,5 9 3 to 6.5,5 3 7 to 6. 5,9 8 to 6. 9, to 6. 50,805 7 to 6. 5, to 6. 56, to , to 6.3 6,587 3 to 6.3 6,870 5 to , to , to 6. 75, to 6. 76,8 7 6 to 6. 77,03 3 to 6. 8, to 6. 83,8 7 5 to 6. 8, to 6. 89, to 6. 90,863 7 to 6. 9, to 6. 97,93 8 to 6. 99,6 7 3 to , to , to 6.0,30 9 to 6.0 3,3 5 9 to , to ,6 6 9 to ,5 7 to 6 0.9, to ,9 5 7 to NOTE: Planting rates over 50,000 seeds/acre are not recommended with subject seed disc and/or drive ratio. Edgevac PLANTING RATES FOR HIGHRATE SOYBEAN 0 CELL DISC 8 tooth CONTACT WHEEL DRIVE SPROCKET APPROXIMATE SEEDS / ACRE FOR VARIOUS ROW WIDTHS 8 9 to to to to NOTE: See General Planting Rate Information and Check Seed Population pages for more information. Always field check seed population to verify planting rates. Rev. 0/

57 M0330 Rate Charts Edgevac Planting Rates for HillDrop Cotton (3 Seeds per Cell), 0 Cell Disc tooth CONTACT WHEEL DRIVE SPROCKET APPROXIMATE HILLS / ACRE FOR VARIOUS ROW WIDTHS 30" Rows Transmission Sprockets Recomm. Speed Average Seed Spacing Drive Driven Range (MPH) In Inches, to 6 7.6, to 6 6.9, to , to , to ,886 5 to , to 6.9, to 6., to 6. 5, to , to , to ,737 7 to , to 6.9 6, 7 3 to 6.7 6, to 6. 7, to 6.9 7,588 9 to 6.9 8, to 6.5 8, to 6. 8, to 6.0 9,03 8 to 6.0 9, to , to ,78 7 to , to , to , to ,508 6 to , to , to 6 0.,9 3 to 6 9.8,38 5 to 6 9.8, to 6 9.8, to 6 9.8,3 7 8 to 6 9.8,7 3 3 to , to , to ,3 5 to ,83 3 to , to , to 6 8.7,9 5 3 to 6 8.7, to 6 8., to 6 8.,99 7 to ,5 6 3 to ,90 8 to , to , to , to ,063 9 to , to , to NOTE: See General Planting Rate Information and Check Seed Population pages for more information. Always field check seed population to verify planting rates. Rev. 0/ 5

58 Rate Charts M0330 Edgevac PLANTING RATES FOR HILLDROP COTTON (3 SEEDS PER CELL), 0 CELL DISC 8 tooth CONTACT WHEEL DRIVE SPROCKET APPROXIMATE HILLS / ACRE FOR VARIOUS ROW WIDTHS 30" Rows Transmission Sprockets Recomm. Speed Average Seed Spacing Drive Driven Range (MPH) In Inches 5,8 5 8 to , to , to 6.8 6, to 6.3 7, to 6. 7,67 5 to 6.8 7, to 6.7 8, 5 3 to 6.3 8, to 6.3 9, to ,8 7 5 to , to ,09 7 to , to , to 6 0.0, to 6 9.7, to 6 9.,385 9 to ,7 3 8 to , to 6 9.0, to 6 8.7,37 8 to 6 8.6, to , to ,3 7 to ,6 5 8 to , to ,0 3 5 to ,0 6 to ,8 5 7 to , to ,098 3 to ,5 5 to , to ,9 6 7 to , to , to , to , to ,5 5 to ,505 3 to ,5 8 6 to , to , to , to , to ,80 7 to , to ,989 8 to ,9 7 3 to ,9 3 9 to ,3 8 3 to ,77 9 to , to , to NOTE: See General Planting Rate Information and Check Seed Population pages for more information. Always field check seed population to verify planting rates. 6 Rev. 0/

59 M0330 Rate Charts Edgevac Planting Rates for Cotton / Small Dry Edible Bean/Sunflower, 5 Cell Disc tooth CONTACT WHEEL DRIVE SPROCKET APPROXIMATE SEEDS / ACRE FOR VARIOUS ROW WIDTHS 30" Rows Transmission Sprockets Recomm. Speed Average Seed Spacing Drive Driven Range (MPH) In Inches 3, to , to , to , to ,0 7 8 to ,9 5 to , to , 5 3 to , 7 6 to , to , to 6 5., 9 7 to 6 5.0,90 7 to 6.9 3, to 6.8, to 6.7 5, to 6.6 7, to 6. 7,89 9 to 6. 9,7 3 8 to 6. 9, to 6. 5, to 6. 5,6 8 to 6. 5, to ,30 7 to , to , to , to ,86 3 to ,586 5 to , to , to , to , to ,59 3 to , to , to ,0 5 3 to , to ,8 7 to , to ,983 8 to ,8 7 3 to ,6 3 9 to , to ,77 9 to , to 6.6 8, to 6.6 8, to 6.5 8,685 7 to ,3 7 9 to , 5 7 to 6. 88, to 6. 9, to 6.3 9, to ,7 7 7 to 6. NOTE: See General Planting Rate Information and Check Seed Population pages for more information. Always field check seed population to verify planting rates. Rev. 0/ 7

60 Rate Charts M0330 Edgevac PLANTING RATES FOR COTTON / SMALL DRY EDIBLE BEAN / SUNFLOWER, 5 CELL DISC 8 tooth CONTACT WHEEL DRIVE SPROCKET APPROXIMATE SEEDS / ACRE FOR VARIOUS ROW WIDTHS 30" Rows Transmission Sprockets Drive Driven Recomm. Speed Range (MPH) Average Seed Spacing In Inches 0, to 6 5., 5 7 to 6.9, to 6.7 5, to 6.6 6, to 6.5 7,76 5 to 6. 8, to 6.3 9, to 6. 9, to 6. 5, to 6.0 5, to ,7 9 7 to ,078 7 to , to ,9 7 3 to ,0 9 5 to ,7 5 9 to ,0 9 to ,7 3 8 to , to , to ,39 8 to , to ,86 7 to , to , to , to ,6 3 to ,9 5 to , to , to , to ,8 7 6 to ,665 3 to 6.6 8,8 8 6 to 6.5 8, to 6.5 8, to , to ,888 7 to 6. 86, to 6. 89,069 8 to , to 6.3 9,8 3 9 to 6.3 9,9 8 3 to 6. 96,36 9 to 6. 00,5 5 9 to 6. 03,9 3 7 to 6.0 0,7 6 9 to ,78 7 to , to 6.9,7 5 7 to 6.9, to 6.9 6, to 6.8 7, to 6.8,5 7 7 to 6.7 NOTE: See General Planting Rate Information and Check Seed Population pages for more information. Always field check seed population to verify planting rates. 8 Rev. 0/

61 M0330 Rate Charts Edgevac Planting Rates for Sunflower, 5 Cell Disc 5 tooth CONTACT WHEEL DRIVE SPROCKET / 9 tooth REVERSER DRIVE SPROCKET APPROXIMATE SEEDS / ACRE FOR VARIOUS ROW WIDTHS 30" Rows Transmission Sprockets Recomm. Speed Average Seed Spacing Drive Driven Range (MPH) In Inches, to 6. 5,0 5 7 to , to , to 6.6 6, to 6. 7,330 5 to 6. 7, to 6.0 8, to 6.6 8, to 6.5 8, to 6. 8, to 6. 9,5 9 7 to ,60 7 to ,6 9 6 to ,9 7 3 to 6 0., to 6 9.9, to 6 9.6,95 9 to 6 9.5, to 6 9., to , to ,767 8 to 6 8.8, to 6 8.5,67 7 to 6 8.5, to ,57 3 to , to ,57 3 to ,69 5 to , to , to , to , to ,933 3 to , to , to , to , to ,9 7 to ,3 6 3 to ,39 8 to , to , to , to ,0 9 to ,8 5 9 to ,5 3 7 to , to ,5 7 to ,0 7 9 to , to , to 6 5., to 6.9, to 6.9, to 6.7 NOTE: See General Planting Rate Information and Check Seed Population pages for more information. Always field check seed population to verify planting rates. Rev. 0/ 9

62 Rate Charts M0330 Edgevac Planting Rates for Large Dry Edible Bean, 5 Cell Disc tooth CONTACT WHEEL DRIVE SPROCKET APPROXIMATE SEEDS / ACRE FOR VARIOUS ROW WIDTHS 30" Rows Transmission Sprockets Drive Driven Recomm. Speed Range (MPH) Average Seed Spacing In Inches 3, to , to , to , to ,0 7 8 to ,9 5 to , to , 5 3 to , 7 6 to , to , to 6 5., 9 7 to 6 5.0,90 7 to 6.9 3, to 6.8, to 6.7 5, to 6.6 7, to 6. 7,89 9 to 6. 9,7 3 8 to 6. 9, to 6. 5, to 6. 5,6 8 to 6. 5, to ,30 7 to , to , to , to ,86 3 to ,586 5 to , to , to , to , to ,59 3 to , to , to ,0 5 3 to , to ,8 7 to , to ,983 8 to ,8 7 3 to ,6 3 9 to , to ,77 9 to , to 6.6 8, to 6.6 8, to 6.5 8,685 7 to ,3 7 9 to , 5 7 to 6. 88, to 6. 9, to 6.3 9, to ,7 7 7 to 6. NOTE: See General Planting Rate Information and Check Seed Population pages for more information. Always field check seed population to verify planting rates. 0 Rev. 0/

63 M0330 Rate Charts Edgevac PLANTING RATES FOR LARGE DRY EDIBLE BEAN 5 CELL DISC 8 tooth CONTACT WHEEL DRIVE SPROCKET APPROXIMATE SEEDS / ACRE FOR VARIOUS ROW WIDTHS 30" Rows Transmission Sprockets Drive Driven Recomm. Speed Range (MPH) Average Seed Spacing In Inches 0, to 6 5., 5 7 to 6.9, to 6.7 5, to 6.6 6, to 6.5 7,76 5 to 6. 8, to 6.3 9, to 6. 9, to 6. 5, to 6.0 5, to ,7 9 7 to ,078 7 to , to ,9 7 3 to ,0 9 5 to ,7 5 9 to ,0 9 to ,7 3 8 to , to , to ,39 8 to , to ,86 7 to , to , to , to ,6 3 to ,9 5 to , to , to , to ,8 7 6 to ,665 3 to 6.6 8,8 8 6 to 6.5 8, to 6.5 8, to , to ,888 7 to 6. 86, to 6. 89,069 8 to , to 6.3 9,8 3 9 to 6.3 9,9 8 3 to 6. 96,36 9 to 6. 00,5 5 9 to 6. 03,9 3 7 to 6.0 0,7 6 9 to ,78 7 to , to 6.9,7 5 7 to 6.9, to 6.9 6, to 6.8 7, to 6.8,5 7 7 to 6.7 NOTE: See General Planting Rate Information and Check Seed Population pages for more information. Always field check seed population to verify planting rates. Rev. 0/

64 Rate Charts M0330 Liquid Fertilizer Piston Pump Application Rates GALLONS PER ACRE Model NGP6055 Pumps With 8 Tooth Sprocket (Planter equipped with two piston pumps.) Pump Setting Row 30" Model NGP7055 Pumps With 8 Tooth Sprocket (Planter equipped with two piston pumps.) Pump Setting Row 30" Charts are for planters equipped with contact drive. Check tires for correct operating pressure. Charts calculated based on a solution weighing ten pounds per gallon. note: Fertilizer application rates can vary from weights calculated in above chart. Make field checks to be sure you are applying fertilizer at desired rate. To check the exact number of gallons your fertilizer attachment will actually deliver on a 30" row spacing:. Remove hose from one fertilizer opener and insert it into a collection container secured planter frame.. Engage fertilizer attachment and drive forward for 7'. 3. Measure fluid ounces caught in container and multiply by 00. Divide that amount by 8. Result is gallons fertilizer delivered per acre when planting in 30" rows. To convert this delivery rate for other row widths, multiply by the following conversion factors: 0" x.50 " x.36 38" x Rinse collection container and repeat test on other rows if necessary. Rev. 0/

65 M0330 Rate Charts Dry Insecticide Application Rates APPROXIMATE POUNDS/ACRE AT 5 MPH (8 KPH) Meter Setting 30" Rows CLAY GRANULES SAND GRANULES NOTE: Chart represents average values and should be used only as a starting point. Granular chemical flows through meter opening at a nearly uniform rate regardless of roller speed. Your actual rate will vary depending on insecticide, planting speed, and plant population. Planting speed/ground speed has the greatest effect on application rate. Field check your actual rate with insecticide you are using at speed and population you will be planting. See Checking Granular Chemical Application Rate in Machine Operation section for more information.. Rev. 0/ 3

66 Rate Charts M0330 Dry Herbicide Application Rates APPROXIMATE POUNDS/ACRE AT 5 MPH (8 KPH) CLAY GRANULES Meter Setting 30" Rows note: Chart represents average values and should be used only as a starting point. Granular chemical flows through given meter opening at a nearly uniform rate regardless of roller speed. Your actual rate will vary depending on specific herbicide, planting speed, and plant population. Planting speed/ground speed has the greatest effect on application rate. Field check your actual rate with herbicide you are using at speed and population you will be planting. See Checking Granular Chemical Application Rate in Machine Operation section for more information. Rev. 0/

67 M0330 Lubrication and Maintenance Lubrication Following pages show locations of all lubrication points. Proper lubrication of moving parts helps ensure efficient operation of your Kinze planter and prolongs the life of friction producing parts. Lubrication Symbols Lubricate at frequency indicated with SAE multipurpose grease. Lubricate at frequency indicated with high quality SAE 0 weight oil or spray lubricant. Sealed Bearings Sealed bearings are used on your Kinze planter to provide trouble free operation. These are located on drive shafts, row units, and transmission bearings. Sealed bearings are lubricated for life and are not serviceable. Air Clutch Lubrication Sealed bearing (Typical) Lubricate air clutches every 7500 hours. Remove Phillips head screw and spray a second burst of silicone spray into each clutch. Reinstall screw. Wheel Bearings Air clutch lubrication All drive, transport, and marker hub wheel bearings should be repacked annually and checked for wear.. Raise wheel off ground.. Check for bearing endplay by moving wheel side to side. 3. Rotate wheel to check for bearing roughness. If bearings sound rough, remove hub and inspect bearings. NOTE: To repack wheel hubs, follow procedure outlined for wheel bearing replacement in this section except bearings and bearing cups are reused. Rev. 0/ 6

68 Lubrication and Maintenance M0330 Drive Chains Lubricate all transmission and drive chains daily with a high quality chain lubricant. Extreme operating conditions such as dirt, temperature, or speed may require more frequent lubrication. If a chain becomes stiff, it should be removed, soaked, and washed in solvent to loosen and remove dirt from joints. Soak chain in oil so lubricant can penetrate between rollers and bushings. Row unit granular chemical drive chains Row unit drive chains Contact wheel drive chains Transmission chains Optional piston pump drive chain Inner module (point row clutch) drive chains 6 Rev. 0/

69 M0330 Lubrication and Maintenance Bushings Lubricate bushings at frequency indicated. Check each bolt for proper torque. If bolt is loose, removed it and inspect bushing for cracks and wear. Replace bushing if necessary. Use only hardened flat washers. Replace damaged flat washers with proper part. Torque hardware to 30 ftlb (76. Nm). Contact wheel arm ( per assembly) Row unit parallel linkages (8 per row) Row unit mounted disc furrower parallel linkages (6 per row) Row unit v closing wheel, covering discs/ single press wheel and/or drag closing wheel eccentric bushings ( per row) Sliding Hitch Linkage Inspect linkage daily to ensure free movement of axle links in slides. Keep axle link slides clean. DO NOT GREASE the axle link slides. Powdered graphite may be used if lubrication is desired. Rev. 0/ 63

70 Lubrication and Maintenance M0330 PTO Shaft Coupling Clean and grease PTO shaft coupling each time pump is installed. Apply coating of highspeed industrial coupling grease, such as Chevron Coupling Grease meeting AGMA CG and CG Standards to extend shaft spline life. PTO pump installed Wrap Spring Wrench Assembly Wrap spring wrench components may require occasional lubrication to operate correctly. Disassembly is required to lubricate.. Remove ¼"0 x ½" cap screw securing idler with sprockets to wrench tightener shaft and remove wrap spring wrench from planter.. Tip wrap spring wrench on its side and lubricate using a high quality spray lubricant. Lubricant must be absorbed into wrap spring area. 3. Reinstall wrap spring wrench on planter. Wrap spring wrench lubrication Liquid Fertilizer Piston Pump Crankcase Oil Level Check crankcase oil daily and maintain at oil level check plug. Fill as needed with EP 90 weight gear oil. Total oil capacity is approximately ¾ pint. Refer to operator and instruction manual supplied with pump and flow divider for more information. Fill plug Check plug Piston pump oil fill and check plug locations 6 Rev. 0/

71 M0330 Lubrication and Maintenance Grease Fittings WARNING Uncontrolled machine movement can crush or cause loss of control resulting in death, serious injury, or damage to property and equipment. Install all safety lockup devices before working under or transporting this equipment. Parts equipped with grease fittings should be lubricated at frequency indicated with an SAE multipurpose grease. Clean fitting thoroughly before using grease gun. Frequency of lubrication recommended is based on normal operating conditions. Severe or unusual conditions may require more frequent attention. Axle and automatic safety lock pivots (7) Ground drive wheel pivot ( per wheel module) Upper and lower hitch linkage ( per link) Row Marker Assemblies ( per side) Seed rate transmission assembly idler pivot ( per assembly) Wing pivot knuckle (3 per knuckle on horizontal shaft) Rev. 0/ 65

72 Lubrication and Maintenance M0330 Link assemblies ( per assembly) Front wear pads () Axle link assemblies ( per assembly) Rear wear pads ( sets 6) Wheel module lift cylinder mount ( per wheel module) Wing pivot knuckle per knuckle on shaft Helper cylinders ( per cylinder) Annually Annually Transport wheel bearing ( per wheel hub) Swivel block () 66 Rev. 0/

73 M0330 Lubrication and Maintenance Piston pump L.H. side () Fill until grease seeps out of bottom drain hole. Piston pump R.H. side (3) Frame Mounted Coulter ( per arm) Notched single disc opener ( per arm) Gauge wheel arms () Seals in gauge wheel arm are installed with lip facing out to allow grease to purge dirt away from seal. Pump grease into arm until fresh grease appears between washers and arm. Rear trailer hitch pivot () Rev. 0/ 67

74 Lubrication and Maintenance M0330 Mounting Bolts and Hardware Before operating planter for the first time, check all hardware is tight. Check all hardware again after first 50 hours of operation and beginning of each planting season. All hardware used on the Kinze planter is Grade 5 (high strength) unless otherwise noted. Grade 5 cap screws are marked with three radial lines on the head. Hardware must be replaced with equal size, strength, and thread type. WARNING Loose transport wheel lug nuts can result in wheel separation from planter and can result in death, serious injury, and damage to property and equipment. Check transport wheel lug nut torque before operating planter for the first time and periodically thereafter. NOTICE Overtightening hardware can reduce its shock load capacity and cause equipment failure. GRADE No Marks GRADE 5 3 Marks TORQUE VALUES CHART PLATED HARDWARE GRADE 8 6 Marks Grade Grade 5 Grade 8 Diameter Coarse Fine Coarse Fine Coarse Fine ¼" 50 inlb 56 inlb 76 inlb 87 inlb 9 ftlb 0 ftlb 5 6" 8 ftlb 9 ftlb 3 ftlb ftlb 8 ftlb 0 ftlb ⅜" 5 ftlb 7 ftlb 3 ftlb 6 ftlb 33 ftlb 37 ftlb 7 6" 5 ftlb 7 ftlb 37 ftlb ftlb 5 ftlb 58 ftlb ½" 35 ftlb 0 ftlb 57 ftlb 6 ftlb 80 ftlb 90 ftlb 9 6" 50 ftlb 60 ftlb 80 ftlb 90 ftlb 5 ftlb 30 ftlb ⅝" 70 ftlb 80 ftlb 0 ftlb 5 ftlb 60 ftlb 80 ftlb ¾" 30 ftlb 5 ftlb 00 ftlb 0 ftlb 80 ftlb 35 ftlb ⅞" 5 ftlb 0 ftlb 30 ftlb 350 ftlb 50 ftlb 500 ftlb " 90 ftlb 05 ftlb 80 ftlb 530 ftlb 675 ftlb 750 ftlb ⅛" 65 ftlb 300 ftlb 600 ftlb 670 ftlb 960 ftlb 075 ftlb ¼" 375 ftlb 5 ftlb 80 ftlb 930 ftlb 360 ftlb 500 ftlb ⅜" 90 ftlb 560 ftlb 00 ftlb 50 ftlb 780 ftlb 030 ftlb ½" 650 ftlb 730 ftlb 50 ftlb 650 ftlb 307 ftlb 670 ftlb NOTE: Torque unplated hardware and bolts with lock nuts approximately ⅓ higher than above values. Torque bolts lubricated prior to installation to 70% of value shown in chart. TORQUE VALUES ALUMINUM Diameter Torque Value ⅛" 800 inlb ⅜" inlb ½" inlb ¾" inlb NOTE: Use these torque values with pneumatic down pressure components. NOTE: Torque EdgeVac fan impeller assembly to motor shaft ⅝"8 hex jam nut 50 ftlb (67.8 Nm). 68 Rev. 0/

75 M0330 Lubrication and Maintenance Tire Pressure WARNING Explosive separation of rim and tire can cause death or serious injury. Overinflation, rim and tire servicing, improper use of rims and tires, worn, or improperly maintained tires could result in a tire explosion. Maintain proper tire pressure. Inflating a tire above or below the recommended pressure can cause tire damage. Mount tires only by properly trained personnel using proper equipment. Replace tires with cuts or bubbles. Replace damaged rims. Replace missing lug bolts and nuts. Do not weld or heat wheel assembly. Heating increases tire pressure. Transport Tires WARNING Overinflation of tires can result in explosive separation of rim and tire and cause death or serious injury. Different size rims are designed for different tire pressures. Inflate to correct pressure for specific rim size. Do not exceed following maximum pressures: Rims stamped with : 75 psi (57. kpa) maximum pressure. Rims stamped with 76 : 00 psi (689. kpa) maximum pressure. Inflation Specifications Row marker Transport Center section lift/gauge Wing lift/gauge Tire locations Ground drive (wings) 5570R psi (57. kpa) Transport 36" x 6" x 7.5" psi (57. kpa) Contact drive.80" x 8" psi (3.7 kpa) Row marker 6" x 6.5" x 8" psi (96.5 kpa) Liquid fertilizer piston pump.0" x 6" psi (3.7 kpa) Rev. 0/ 69

76 This page left blank intentionally.

77 M0330 Lubrication and Maintenance Single and TwoSpeed Point Row Clutch Maintenance Point row clutch is permanently lubricated and sealed and requires no periodic maintenance. Twospeed point row clutch is similar in design and operation to standard point row clutch except for twospeed function. Solenoid Plunger Spring Wrap spring Output hub Stop collar Actuator arm Input hub Single point row clutch main parts Output hub Stop collar Input hub Wrap spring Actuator arm Spring Stop collar Plunger Wrap spring Solenoid Twospeed point row clutch main parts Rev. 0/ 6

78 Lubrication and Maintenance M0330 TESTING AND FUSE REPLACEMENT Control box main fuse L.H. point row clutch R.H. point row clutch L.H. reduced rate Control box main fuse L.H. point row clutch R.H. reduced rate R.H. point row clutch Single speed point row clutch control box (Front View) Two speed point row clutch control box (Rear view) NOTE: Replace all point row fuses with MDL 0 amp slow blow fuses. If the clutch or clutches fail to operate, first determine if problem is electrical or mechanical. Place operation switch in RIGHT or LEFT position. Solenoid plunger will retract causing a clicking sound if it is operating properly. Touch plunger with a metal object to check if it is electrically magnetized. Check clutch and wiring harness for power with a test light or volt meter. NOTE: R.H. clutch operates clockwise and L.H. clutch operates counterclockwise. Clutch parts such as the wrap spring are side specific. Use correct repair part if a clutch must be repaired. Also see Point Row Clutch Troubleshooting in Troubleshooting section. ACTUATOR ARM ADJUSTMENT ⅛"(±/3") gap Gap between actuator arm and stop on stop collar should be ⅛"(±/3") when solenoid is NOT engaged. Loosen nut on mounting pin and move pin in slot until there is a ⅛"(±/3") gap between arm and stop on stop collar. Retighten nut. 6 Rev. 0/

79 M0330 Lubrication and Maintenance Planter Mounted Pump Drive and Oil Cooler Oil filter location Oil cooler location NOTICE Clean and grease PTO shaft coupling with highpressure industrial coupling grease (Chevron coupling grease or equivalent) meeting AGMA CG and CG Standards each time driveshaft is installed or premature wear and equipment failure can occur. NOTE: Periodically check and clean oil coolers.. Replace 0micron spinon filters on each wing annually.. Fill system with SAE 0W0 multigrade wide temperature range transmission hydraulic fluid. Reservoir capacity is approximately 0 gal (37.8L). 3. Start system and run with tractor at idle and fans turned off for minutes. Switch fans to full speed and run with tractor at idle for minutes.. Check reservoir fluid level and fill as required. Hydraulic fluid level should be within "" from top of reservoir after pump has run and hydraulic hoses have been primed to allow fluid to expand when heated. Digital Vacuum Gauge Adjustment Digital vacuum gauge is factory calibrated. However, vacuum varies throughout manifold system and it may be necessary to adjust digital readout to match actual vacuum at meter. Load seed discs with seed and compare digital vacuum gauge readouts to reading taken from analog gauges or a hand held gauge at several meters along length of planter. Elbow connections located on covers of seed meters allow testing of meter vacuum levels without removing vacuum hoses. EdgeVac digital vacuum gauge If there is more than " or " (H O) difference, adjust digital gauge by inserting a small flat bladed screwdriver into opening on back of digital gauge housing and turning potentiometer until digital gauge displays vacuum present at meter. Compare readings at 0" and 0" of vacuum. Rev. 0/ 63

80 Lubrication and Maintenance M0330 Check Valve A check valve is located in each vacuum fan motor block assembly and operates as a return line check to prevent vacuum fan motor reverse operation. Check valves are also located in valve block on left wing and trap oil flow in planter s lift system to keep toolbar level during field operation. Another check valve is located in junction block on left wing of planter on Row 30" and 36 Row 0" sizes. Remove and inspect valve If it does not operate properly. Check for foreign material and if Oring is leaking internally. Replace if defective. Dentent Lever Valve Detent lever valve, located near tower assembly on R.H. side of machine, blocks oil flow from master cylinders until slave cylinders are at same height as master cylinders when planter is being lowered from transport into field position. Contact your Kinze Dealer for service. Flow Control Valves Two flow control valves are located in valve block on right wing of planter. Flow control valves should be adjusted for row marker raise and lower speed as part of assembly procedure or upon initial operation. If valve fails to function properly or requires frequent adjustment, it should be removed for inspection. Check for foreign material and contamination on valve and seating areas of valve body. Replace defective components. Pressure Relief Valves Pressure relief valve in valve block on left wing of planter functions during lowering out of raised transport sequence. Valve is factory set and should require no additional adjustment. Pressure relief valve located in valve block on tongue functions during tongue extend cycle. This pressure relief valve ensures latch cylinder extends and releases prior to tongue extending. Valve is factory set and should require no additional adjustment. Contact your Kinze Dealer for service. NOTICE Connect hydraulic motor case drain to a case drain return line with zero pressure on tractor or hydraulic motor will be damaged. DO NOT connect hydraulic motor case drain to SCV outlet. Contact tractor manufacturer for specific details on zero pressure return. Relief Valve Cartridge Pressure relief valve located in vacuum fan motor block assembly helps prevent damage to vacuum fan motor by limiting pressure in the motor case drain line. It is set to open at 35 PSI. If valve fails to function properly, it should be removed for inspection. Check for foreign material and contamination on valve and the seating area of valve body. Replace if defective. 6 Rev. 0/

81 M0330 Lubrication and Maintenance Solenoid Valve Coil Solenoid valve consists of a chambered body with an electric coil actuated cartridge valve. If solenoid or solenoids fail to operate, first determine if problem is electrical or hydraulic. If valve is working properly, a click will be heard when solenoid coil is energized and valve stem opens. If no sound is heard, check solenoid coil by touching top of coil housing with a metallic object such as a pliers or screwdriver. If coil is working properly, coil housing will be strongly magnetized when energized. If voltage to coil is low it will be weakly magnetized when energized and no click will be heard. Cartridge Stroke Limiter Valve Stroke limiter valve, located near tower assembly on L.H. side of machine, limits height planter will raise during turn around when planter is in field operation. Contact your Kinze Dealer for service. Chain Tension Adjustment ¼" or less Chain link storage location (each wing) Most drive chains have a spring loaded idler and are selfadjusting. The only adjustment needed is to shorten chain if wear stretches chain and reduces spring tension. Check idler pivot point periodically to ensure they rotate freely. On chains with slotted idlers for adjustment, adjust so chain has ¼" or less sag at longest span. See Wrap Spring Wrench Assembly for additional information. Additional chain links can be found in the storage area located at end of planter frame on inboard side of transport hook. Rev. 0/ 65

82 Lubrication and Maintenance M0330 Stroke Limiter (Height Stop) Valve Adjustment Field turn around height of toolbar should measure 39"" from ground if stroke limiter valve is correctly adjusted.. Lower planter to ground and hold hydraulic lever for 50 seconds to purge air and rephase system. Detent arm Pivot shaft Rod assembly 5½" Stroke limiter valve Front. Check rod assembly adjustment bolt is set at 5¾" pin to pin when planter is fully lowered. Adjust as needed. Line from valve plunger to pivot shaft Valve plunger Cam activator Stroke limiter valve 3. Check stroke limiter (height stop) valve plunger is depressed and pointing in a straight line to center of pivot shaft on cam activator.. Loosen detent arm (height stop assembly) clamping bolt and rotate detent arm over depressed stroke limiter valve plunger. Valve plunger should be fully depressed when detent arm is rotated over plunger arm, but must not bind. If binding occurs, move valve assembly away from detent arm while keeping valve plunger aligned with pivot shaft. Slide stroke limiter valve up or down in slotted mounting holes as needed to adjust. Tighten stroke limiter valve mounting bolts and recheck adjustment. Be sure detent arm is positioned as shown and tighten detent arm clamping bolt. 5. Raise planter until stroke limiter valve (height stop assembly) halts lift cylinder. Toolbar should measure 39"" from ground. If adjustment is needed, loosen detent arm clamping bolt and rotate detent arm counterclockwise to reduce and clockwise to increase lift height. Tighten clamping bolt and mark a line on detent arm and cam activator shaft for easier alignment later. NOTE: When lowering from transport position, planter toolbar should level out to a height of 39" from ground at field turn around. If it doesn t, rephase and/or remove air from the hydraulic lines and recheck toolbar height. Repeat above adjustments as needed. 66 Rev. 0/

83 M0330 Lubrication and Maintenance Detent Lever (Lowering Control) Valve Adjustment Center of planter should drop until toolbar is level and then entire planter should lower evenly when lowering planter for field operation from transport position if detent lever valve is correctly adjusted. Cam Pivot shaft Front Detent lever valve. Lower planter to field turn around position and check toolbar height is 39"". Adjust following procedure for stroke limiter valve adjustment. Stroke limiter (height stop) valve must be correctly adjusted prior to adjusting detent lever (lowering control) valve. Stainless bushing Cam Plunger Cam /6" gap Detent lever valve Planter fully raised Planter lowering toolbars level. Raise planter to fully raised position. With cam positioned as shown, adjust detent lever (lowering control) valve in its mounting slots so there is /6" gap between stainless bushing and cam. Lower edge of cam must be above pivot point of stainless bushing. NOTE: While lowering planter, center cylinders should begin to retract while wing cylinders stay extended. When toolbar becomes level, large radius of cam should cause arm to depress plunger on detent lever valve allowing wing cylinders to start retracting. 3. Lower planter. If center of planter drops lower than wings, loosen set screws and rotate cam clockwise. If wing cylinder begins to retract too early and wings drop lower than center of planter, rotate cam counterclockwise. Adjust cam with planter in raised position.. After final adjustment, remove one set screw and drill a depression in cam activator shaft with a ¼" drill bit. Replace set screw and repeat with second set screw. Rev. 0/ 67

84 Lubrication and Maintenance M0330 Row Marker Bearing Lubrication or Replacement Outer cup Flat washer Slotted hex nut Hub Grease seal Bearing Spindle Marker blade Dust cap Inner cup Hub shield Bearing Retainer Cotter pin. Remove retainer and marker blade.. Remove dust cap from hub.. Remove hub shield. Note direction of installation. 3. Remove cotter pin, slotted hex nut, and washer.. Slide hub from spindle. 5. Remove bearings and cups and discard if bearings are being replaced. Clean hub and dry. Remove bearings only and not cups if repacking. 6. Press in new bearing cups with thickest edge facing in. (Bearing replacement procedure only.) 7. Pack bearings with heavy duty wheel bearing grease thoroughly forcing grease between roller cone and bearing cage. Fill the space between the bearing cups in the hub with grease. 8. Install rubber seal into grease seal. Place inner bearing in place and press in new rubber seal/grease seal. 9. Clean spindle and install hub. 0. Install outer bearing, washer and slotted hex nut. Tighten slotted hex nut while rotating hub until there is some drag. This ensures all bearing surfaces are in contact. Back off slotted nut to nearest locking slot and install cotter pin.. Fill dust caps approximately ¾ full of wheel bearing grease and install on hub.. Install hub shield. 3. Install marker blade and retainer on hub. Tighten hardware evenly. 68 Rev. 0/

85 This page left blank intentionally.

86 Lubrication and Maintenance M0330 WARNING Uncontrolled machine movement can crush or cause loss of control resulting in death, serious injury, or damage to property and equipment. Install all safety lockup devices before working under or transporting this equipment. Lift/Ground Drive Wheel Bearing Repack or Replacement Hub Jam nuts Bearing cup Spindle Inner bearing Outer bearing Bearing cup. Raise tire clear of ground and remove wheel.. Remove double jam nuts and slide hub from spindle. 3. Remove bearings and cups and discard if bearings are being replaced. Clean hub and dry. Remove bearings only and not cups if repacking.. Press in new bearing cups with thickest edge facing in. (Bearing replacement procedure only.) 5. Pack bearings with heavy duty wheel bearing grease thoroughly forcing grease between roller cone and bearing cage. Fill space between bearing cups and hub with grease. 6. Place inner bearing in place. 7. Clean spindle and install hub. 8. Install outer bearing and jam nut. Tighten jam nut while rotating hub until there is some drag. This ensures all bearing surfaces are in contact. Back off jam nut ¼ turn or until there is only slight drag when rotating hub. Install second jam nut to lock against first. 9. Install wheel on hub. Tighten hardware evenly. 630 Rev. 0/

87 M0330 Lubrication and Maintenance WARNING Uncontrolled machine movement can crush or cause loss of control resulting in death, serious injury, or damage to property and equipment. Install all safety lockup devices before working under or transporting this equipment. Transport Wheel Bearing Replacement Spindle Inner bearing ¾"6 flange nut Bearing cup Outer bearing Bearing cup Seal Dust cap Hex head cap screw Cotter pin Seal " washer " slotted nut Hub. Raise tires clear of ground and support with jack stand. Remove wheels.. Remove dust cap attachment hardware and cap from wheel hub. 3. Remove cotter pin, slotted nut, and " washer.. Slide hub from axle spindle. Use a hub puller if necessary. 5. Remove bearings and cups from hub and discard. Thoroughly clean and dry wheel hub. 6. Press in new bearing cups with thickest edges facing in. 7. Pack bearing with heavyduty wheel bearing grease. Thoroughly force grease between roller cone and bearing cage. Fill space between bearing cups and hub with grease. 8. Place inner bearing in hub and press in new grease seal with lip pointing towards bearing. 9. Clean axle spindle and install hub. 0. Install outer bearing, " washer, and slotted nut. Tighten slotted nut while rotating hub until there is some drag. This ensures all bearing surfaces are in contact. Back off slotted nut to nearest locking slot and install cotter pin. Check bearing endplay.. Fill dust cap half full of wheel bearing grease and install on hub with four hex head cap screws.. Install wheels and remove jack stand. Torque ¾" flange nuts to 80 ftlb (379.6 Nm). Rev. 0/ 63

88 Lubrication and Maintenance M0330 Fertilizer Check Valve Cleaning and Repair Oring Spring Guide Valve ball Valve seat Direction of flow. Unscrew valve body and separate halves. Note direction and location of parts.. Clean and inspect parts. Flush with clean water. Replace damaged parts. 3. Reassemble exactly as shown. Oring and valve seat must be firmly in place inside each half of valve body. Piston Pump Storage NOTICE Entrance of air into pump will cause rapid and severe corrosion. KEEP AIR OUT OF PUMP! NOTE: SUSPENSION FERTILIZER must be flushed from pump for ANY storage period.. Flush pump with 5 to 0 gallons of fresh water and circulate until all corrosive salts are dissolved in pump.. Set pump on 0. Draw in a mixture of half diesel fuel and 0 weight oil until discharge is clean. Plug inlet and outlet. 63 Rev. 0/

89 M0330 Lubrication and Maintenance Preparation for Storage Store planter in a dry sheltered area if possible. Remove all trash wrapped on sprockets or shafts and remove dirt that can draw and hold moisture. Clean all drive chains and coat with a rust preventative spray, or remove chains and submerge in oil. Lubricate planter and row units at all lubrication points. Inspect planter for parts that in need of replacement and order during off season. Make sure all seed and granular chemical hoppers are empty and clean. Remove seed discs from seed meters, clean and store meters in a rodentfree, dry area with discs removed. Store seed discs vertically on a dowel or pipe. Remove vacuum hose from each seed meter. Operate vacuum fan at full hydraulic flow from tractor for two minutes to clear manifolds, hoses and fittings of dust and debris. Clean breather on analog vacuum and pressure gauges. Disassemble, clean and grease all Ujoint slides. Grease or paint disc openers/blades and row marker disc blades to prevent rust. Flush liquid fertilizer tanks, hoses and metering pump with clean water. See Piston Pump Storage if applicable. Empty dry fertilizer hoppers. Clean hoppers. Disassemble and clean metering augers. Reassemble, coating all metal parts with rust preventative. ASD System: Clean out ASD hopper, entrainment assembly, and delivery hoses. Disconnect delivery hoses from entrainer ports. Install small orange caps onto ports. Attach hoses to caps. Disconnect delivery hoses from air dissipator at each row unit. Install large orange caps. Attach hoses to caps. Check all bolts and fasteners used to assemble and attach entrainment device are tight (if applicable). Loosen knobs on entrainer cleanout doors to remove pressure from door gaskets. Inspect all seed delivery hoses and replace any that are worn, cut, or cracked. Entrainer cap Air dissipator cap Rev. 0/ 633

90 This page intentionally left blank.

91 M0330 Lubrication and Maintenance Electrical Wiring Diagram for Light Package Light packages supplied on Front Folding Planters meet ASABE Standards. Check with tractor manufacturer for correct wiring harness to be wired into lights on your tractor,. *Optional customersupplied auxiliary lights and wires may be wired into existing plug terminals. Rev. 0/ 635

92 Lubrication and Maintenance M0330 Electrical Control Console Schematic NOTICE Disconnect control console from tractor battery before doing any electrical work or shorting will damage equipment. Keep wiring harnesses away from high temperature areas or sharp edges. DO NOT route wiring harnesses along battery cables. Use cable ties to keep wire harness away from moving parts on tractor and planter. Ground connections to tractor frame must be clean to provide good electrical contact. LEFT MARKER OFF RAISE MAIN FUSE 5A RIGHT OFF ROTATE LEFT USE 0 AMP DELAY ACTION ONLY POINT ROW OFF WING LOCK TONGUE OFF AUXILIARY MARKERS WILL NOT FUNCTION WITH AUXILIARY SWITCH ON ON RIGHT fi Pin C Black/Red (Ground) Pin T Black (Ground) Black ( VDC) Pin R Brown (Left point row clutch) Pin G Orange (Right point row clutch) Delay Action Fuse (0A SlowBlow) Red (+ VDC) Pin H Blue (Left marker) Pin O Red (Right marker) Indicator light Main fuse (5A) Point row clutch switch Marker switch Auxiliary switch Rotate/Tongue switch Pin W Orange/Black (Auxiliary) Pin B Blue/Red (Rotate) Raise/Wing Lock switch Pin F Yellow/Red (Not used) Pin V Blue/Black (Raise) Pin A Orange/Red (Tongue) NOTE:. Operating row marker or point row switch in either direction lights panel light.. Point row clutch switch operates independently from rest of control box. 3. Power to row marker switch is fed through auxiliary switch and two transport function switches. Operating any switch in lower row disables row marker function and turns off panel light. (If point row clutch switch is OFF.). See page 6 for twospeed point row clutch electrical control console and wiring harness schematics. 636 Rev. 0/

93 M0330 Lubrication and Maintenance Electrical Wiring Harness Schematic (on tractor) Pin F YELLOW/RED (Not Used) Pin R BROWN (Not Used) Pin G ORANGE (Not Used) Pin H BLUE (L.H. Marker) Pin B BLUE/RED (Fold) Pin U RED/BLACK (Not Used) Pin S YELLOW (Not Used) Pin O RED (R.H. Marker) Pin V Blue/Black (Raise) Pin T Black (Ground)( Gauge) Pin C Black/Red (Ground) Pin W Orange/Black (Auxiliary) Red (+ VDC) Black ( VDC)( Gauge) Pin A ORANGE/RED (Slide) Brown Orange Red Pin L GREEN ( C MONITOR DATA) Pin M BLACK ( B MONITOR GROUND) Pin K WHITE ( A MONITOR +V) To battery 3 socket capacity Rev. 0/ 637

94 Lubrication and Maintenance M0330 Electrical Wiring Harness Schematic (on planter) Pin A (Tongue Retract/Extend) ORANGE/RED Ports V9 & V0 Pin C (Ground) BLACK/RED 3 Pin Capacity VALVE BLOCK Located On Hitch VALVE BLOCK Located On R.H. Wing Pin F YELLOW/RED (NOT USED) Pin L GREEN ( C MONITOR DATA) Pin M BLACK ( B MONITOR GROUND) Pin K WHITE ( A MONITOR +V) ( Gauge) Pin R BROWN (L.H. Point Row Clutch) RED Clutch Solenoid Terminals On L.H. Side Of Planter Pin G ORANGE (R.H. Point Row Clutch) Pin H BLUE (L.H. Marker) Port V BLACK To Ground Clamp BLUE NOT USED Pin B BLUE/RED (Rotate) Ports V3 & V BLUE Pin S YELLOW (L.H. TwoSpeed Clutch)* Pin U RED/BLACK (R.H. TwoSpeed Clutch)* Clutch Solenoid Terminals On R.H. Side Of Planter Pin O RED (R.H. Marker) Port V Pin V BLUE/BLACK (Raise)** Pin T BLACK (Ground)** ( Gauge) Pin W ORANGE/BLACK (Auxiliary) ** NOTE: Harness To Port V On Valve Block Located On Tower * See page 6 if equipped with optional TwoSpeed Point Row Clutch Package. 638 Rev. 0/

95 M0330 Lubrication and Maintenance Valve Block Located on Hitch Terminal Strip.ORANGE/RED.ORANGE/RED 3. BLACK/RED 3. BLACK/RED V9 V0 To Valve Block On R.H. Wing. ORANGE/RED Pin A (Tongue Retract/Extend) Port V9. ORANGE/RED Pin A (Tongue Retract/Extend) Port V0 3. BLACK/RED Pin C (Ground) Rev. 0/ 639

96 Lubrication and Maintenance M0330 Valve Blocks Located on Tower and R.H. Wing.GREEN ( C ).BLACK ( B ) 3.WHITE ( A ) D3 D7 VALVE BLOCK Located On Tower V D5 Terminal Strip RED BLACK (GROUND).YELLOW/RED 5.ORANGE/BLK 5.ORANGE/BLK 6.BROWN 7.YELLOW 8.ORANGE 9.RED/BLK 0.BLUE/BLK.BLUE.BLUE/RED 3.RED GROUND RED BLUE RED BLUE RED VALVE BLOCK Located On R.H. Wing Terminal Strip Ground Clamp GROUND GROUND V3 V V V GROUND GROUND GROUND. GREEN Pin L ( C MONITOR DATA). BLACK Pin M ( B MONITOR GROUND) 3. WHITE Pin K ( A MONITOR +V). YELLOW/RED Pin F (NOT USED) 5. ORANGE/BLACK Pin W (Auxiliary) 6. BROWN Pin R (L.H. Point Row Clutch) 7. YELLOW Pin S (L.H. TwoSpeed Clutch)* 8. ORANGE Pin G (R.H. Point Row Clutch) 9. RED/BLACK Pin U (R.H. TwoSpeed Clutch)* 0. BLUE/BLACK Pin V (Raise). BLUE Pin H (L.H. Marker) Port V. BLUE/RED Pin B (Rotate) Ports V3 And V 3. RED Pin O (R.H. Marker) Port V. BLACK Pin T (Ground) GROUND.BLACK (GROUND) * See page 6 if equipped with optional TwoSpeed Point Row Clutch Package. 60 Rev. 0/

97 M0330 Lubrication and Maintenance Control Console Schematic (Optional TwoSpeed Point Row Clutches) Pin C BLACK/RED (Ground) B L A C K ( VDC) RED (+ VDC) Pin R BROWN (L.H. Point Row Clutch) Pin G ORANGE (R.H. Point Row Clutch) Pin W ORANGE/ BLACK (Auxiliary) Pin T BLACK (Ground) Pin S YELLOW (L.H. TwoSpeed Clutch) Pin U RED/BLACK (R.H. TwoSpeed Clutch) Pin H BLUE (L.H. Marker) Pin O RED (R.H. Marker) Pin F YELLOW/RED (NOT USED) Pin V BLUE/BLACK (Raise) Pin A ORANGE/ RED (Tongue) Pin B BLUE/RED (Rotate) RED L.H. To Brown R.H. To Orange NOTE: STYLE A With Fork Terminals And Contact Connectors Shown STYLE B Will Have Fork Terminals Only BLUE Reduced Rate Clutch Solenoid BLACK To Ground Clamp BLUE L.H. To Yellow R.H. To Red/Black RED Point Row Clutch Solenoid BLACK Ground Wire Connects To One Terminal Jumper Wire Input Output Point Row Clutch Switch Auxiliary Switch Raise/Wing Lock Switch Marker Switch Rotate/Tongue Switch Reduced Rate Clutch Switch NOTE:. Point row and reduced rate clutch switches operate independently from rest of control console.. Power to marker switch is fed through auxiliary switch and two transport function switches. Operating any switch in lower row disables marker function and turns off panel light for markers. NOTICE Disconnect control console from tractor battery before doing any electrical work or shorting will damage equipment. Keep wiring harnesses away from high temperature areas or sharp edges. DO NOT route wiring harnesses along battery cables. Use cable ties to keep wire harness away from moving parts on tractor and planter. Ground connections to tractor frame must be clean to provide good electrical contact. Rev. 0/ 6

98 Lubrication and Maintenance M0330 Electrical Wiring Harness Schematic (Vacuum Fan Control) White (Motor Up) Blue (Motor Down) Brown (Motor Up) Green (Motor Down) Yellow (Coil Power) Black (Ground) Black (Ground) Yellow (Coil Power) Red (Power) Black (Ground) Orange/Black (Vacuum Signal) Red (Power) Black (Ground) Orange (Vacuum Signal) To digital vacuum gauge. 6 Rev. 0/

99 M0330 Lubrication and Maintenance Hydraulic schematic (ASD System) Case drain (⅜" hose) Pressure (⅝" hose) P P ASD fan block R Return (¾" hose) R ASD fan block NOTICE Failure to connect to a return with zero pressure will damage hydraulic motor. Connect hydraulic motor case drain to a case drain return line with zero pressure on tractor. DO NOT connect hydraulic motor case drain to SCV outlet. Contact tractor manufacturer for specific details on zero pressure return. Rev. 0/ 63

100 Lubrication and Maintenance M0330 Hydraulic Schematic (Vacuum Fan System) Vacuum fan valve block Oil cooler Vacuum fan Oil reservoir NOTICE Failure to connect to a return with zero pressure will damage hydraulic motor. Connect hydraulic motor case drain to a case drain return line with zero pressure on tractor. DO NOT connect hydraulic motor case drain to SCV outlet. Contact tractor manufacturer for specific details on zero pressure return. PTO pump 6 Rev. 0/

101 M0330 Lubrication and Maintenance Case drain (⅜" hose) Pressure (⅝" hose) Vacuum fan valve block Return (¾" hose) Oil Cooler Pressure (⅝" hose) Vacuum fan Return (¾" hose) Case drain (⅜" hose) Pressure (⅝" hose) Oil reservoir Return (¼" hose) Return (¾" hose) Case drain (⅜" hose) Rev. 0/ 65

102 Lubrication and Maintenance M0330 Hydraulic System Schematic ( Row 0"/30") Pilot Operated Check Valve Pressure Relief Valve Row Marker Flow Control Valve Solenoid Valve Holds Load In One Direction Solenoid Valve Holds Load In Both Directions Check Valve Valve block on R.H. wing A B A8 B8 A9 B9 V6 V5 V Marker speed raise B6 V3 A6 B V7 A Marker speed lower V V8 V B7 A7 B5 A5 R.H. marker cylinder L.H. marker cylinder 66 Rev. 0/

103 M0330 Lubrication and Maintenance Pilot Pressure Booster Valve Block Pilot Operated Check Valve Check Valve VALVE BLOCK ON L.H. WING C9 Check Valve V DETENT LEVER VALVE C7 D5 D E B D C A Front B D C A Blue BB (Pressure) Red BB (Pressure) Blue AA (Return) Red AA (Return) HITCH PARALLEL PARALLEL LINKAGE LINKAGE CYLINDER CYLINDER Rev. 0/ 67

104 Lubrication and Maintenance M0330 Hydraulic System Schematic (36 Row 0") Pilot Operated Check Valve Pressure Relief Valve Row Marker Flow Control Valve Solenoid Valve Holds Load In One Direction ASSIST CYLINDER VALVE BLOCK ON R.H. WHEEL MODULE Solenoid Valve Holds Load In Both Directions Check Valve A B VALVE BLOCK ON R.H. WING A8 B8 V6 V5 V A9 B9 Marker Speed Raise R.H. MARKER CYLINDER B6 A6 B A V7 V3 V8 V Marker Speed Lower V B7 A7 B5 A5 L.H. MARKER CYLINDER 68 Rev. 0/

105 M0330 Lubrication and Maintenance Pilot Pressure Booster Valve Block Pilot Operated Check Valve Check Valve V C9 Check Valve VALVE BLOCK ON L.H. WHEEL MODULE ASSIST CYLINDER C7 D5 D DETENT LEVER VALVE E B D C A B D C A Direction of Travel Blue BB (Pressure) Red BB (Pressure) Blue AA (Return) Red AA (Return) HITCH PARALLEL PARALLEL LINKAGE LINKAGE CYLINDER CYLINDER Rev. 0/ 69

106 Lubrication and Maintenance M0330 A68 A80 WING WHEEL CYLINDERS (MASTER) Row A80 A3 WING WHEEL CYLINDERS 36 Row (L.H. mirrors R.H.) Hydraulic Valve Block Locations A036 A8 A673 A678 A67 LIFT CYLINDER (SLAVE) LIFT CYLINDER (SLAVE) A05 A67 Raise Lower A670 A80 WING WHEEL CYLINDERS (MASTER) Same as row Same as row To D7 (R.H.) or D6 (L.H.) tee Same as row 650 Rev. 0/

107 M0330 Lubrication and Maintenance Hydraulic Valve Block Functions A670 Valve Block On L.H. Wing A68 Valve Block on R.H. Wing 500 psi relief valve. Allows lower from transport. Controls markers and marker speed. Routes hydraulic flow to tongue and fold cylinders. A67 Valve Block On Tower Oil enters D3 and flows past V to rod end of slave cylinders when lowering planter. Oil from rod side of slave cylinders goes in D6 and D7 when raising planter. V is closed so oil goes out D5 to height stop plunger and comes back in on D to tractor. A80 Pilot Operated Check Valve Traps oil in butt ends of wing cylinders until pilot pressure from A8 opens check valves and allows cylinders to retract. If L.H. side raises slowly or is erratic, check P to ensure Oring and backups are removed. Oil flows directly to tractor when V is energized and allows planter to raise to transport height. A8 A67 Valve Block On Front Hitch Controls tongue lift cylinder and routes hydraulic hoses to left and right side drag links. Opens pilot operated check valves in A80 when lowering. A05 Stroke Limiter Valve Shuts off hydraulic flow to limit field turn height. A673 Junction Block On Hose TakeUp Planter lift circuit juction block. Routes hydraulic flow to all planter lift related valves. A678 Detent Lever Valve Blocks oil from exiting wing cylinders when lowering until center of planter reaches a predetermined height (level toolbars) and then is mechanically opened. A3 (36 row 0 only) Valve Block on L.H. and R.H. Wheel Module Blocks flow from port to until pressure exceeds valve set pressure (000 psi). Allows free reverse flow from to if pressure at is at least 0 psi greater than pressure at. A036 Pilot Pressure Booster Valve Block Located on inboard side of A8 to create 000 psi pressure on pilot lines to make wing wheels lower togther. Rev. 0/ 65

108 Lubrication and Maintenance M0330 Air Clutch Airline Schematic A B C C B A P/N: A86 High Pressure Sensor (00 p.s.i.) A B C Clutch valve assembly Clutch valve assembly V V V V V V 6 7 V V Row 0"/30" A B C C B A P/N: A86 High Pressure Sensor (00 p.s.i.) A B C Clutch valve assembly Clutch valve assembly V V 7 8 V3 V V V V3 V Row 0" 65 Rev. 0/ TM

109 This page left blank intentionally.

110 Troubleshooting M0330 KPM III Electronic Seed Monitor PROBLEM POSSIBLE CAUSE SOLUTION Faulty seed tube sensor. Replace sensor. Single sensor communication alarm comes on. Sensor communication alarms come on for all sensors. Sensor communication alarms come on for some sensors. Faulty monitor values (such as speed, area, etc.) being displayed. Underplanting or no planting alarm on a single sensor when planting (alarm on with a single bargraph segment on and a flashing row number on a single row. Seed tube sensor dirty or blocked warning comes on. LED on seed tube sensor will not come on. Erroneous MPH readings at idle. (Radar Distance Sensor Only) Break in the harness just before the seed tube sensor. Dirty or corroded connector. Faulty monitor. Break in the harness just after the monitor. Dirty or corroded connector. Break in the harness. Dirty or corroded connector. Incorrect monitor settings. Faulty radar/magnetic distance sensor. Improperly mounted radar sensor. Seed tube sensor is blocked. Faulty seed tube sensor. Meter not planting or underplanting. Chain broken or off sprocket. Seed tube sensor is dirty. Faulty seed tube sensor. Faulty seed tube sensor. Dirty or corroded connector. Break in the harness just before the sensor. Radar sensor not located in a stable location. Inspect for break in harness and repair. If break can't be found, replace harness section. Clean connector. Repair/Replace monitor. Inspect for break in harness and repair. If break can't be found, replace harness section. Clean connector. Inspect for break in harness and repair. If break can't be found, replace harness section corresponding with alarming sensors. Clean connector. Change settings to properly correspond to the system. Replace sensor. Properly mount sensor. Clean sensor. Replace sensor. Repair/replace meter. Repair as necessary. Clean sensor. Replace sensor. Replace sensor. Clean connector. Repair harness. Relocate to a more stable location. Lift Circuit PROBLEM POSSIBLE CAUSE SOLUTION Field turn around toolbar Stroke limiter valve is out of adjustment. Consult your Kinze Dealer for height is not 39. service. Planter not leveling out when lowering from transport. Detent lever valve out of adjustment. Consult your Kinze Dealer for service. Planter settles. Lift cylinder leaking. Repair or replace cylinder. 7 Rev. 0/

111 M0330 Troubleshooting Piston Pump PROBLEM POSSIBLE CAUSE SOLUTION Pump hard or impossible to Valves fouled or in wrong place. Inspect and clean valves. prime. Air leak in suction line. Repair leak. Pump set too low. Adjust pump setting. Packing washers worn out. Replace. Low metering. Valves fouled or in wrong place. Inspect and clean valves. Air leak in suction line. Repair leak. Pump set too low. Adjust pump setting. Broken valve spring. Replace spring. Over meters. Broken discharge valve spring. Replace spring. Trash under valves. Inspect and clean valves. Improper rate setting. Adjust pump setting. Leaks through when stopped. Broken discharge valve spring. Replace spring. Trash under valves. Inspect and clean valves. Fertilizer solution leaking Packing washers worn out. Replace. under stuffing box. Pump using excessive oil. Oil seals or Oring worn and leaking. Replace. Pump operates noisily. Crankcase components worn excessively. Inspect and replace if necessary. Rev. 0/ 73

112 Troubleshooting M0330 Point Row Clutch PROBLEM POSSIBLE CAUSE SOLUTION No clutches disengage. Main fuse blown in control console. Replace defective fuse. Poor terminal connection in wiring harness. Repair or replace. Wiring damage in wiring harness. Repair or replace. Low voltage at coil. ( volts required) Check battery connections. One section of planter will not reengage. Shear pin at seed drive transmission(s) sheared. Replace pin with one of equal size and grade. One clutch will not engage. Fuses blown. Replace defective fuses. Actuator arm and plunger stuck in Remove, free up, and reinstall. disengaged position. Actuator arm out of adjustment. Adjust actuator arm mounting pin in slot so that actuator arm clears stop on stop collar by approximately ⅛" when clutch is rotated. Wrap spring broken or stretched. Disassemble clutch and replace spring. Something touching the stop collar. Check to ensure collar is free to turn with clutch. Clutch assembled incorrectly. Check clutch and diagram for correct assembly. Clutch slipping. Wrap spring stretched. Lock clutch output shaft from turning. Place torque wrench on input shaft and rotate in direction of drive. After input shaft has rotated a short distance the wrap spring should tighten onto the input hub. If slippage occurs at less than 00 ft. lbs. replace spring. If spring still slipsafter installing new spring, replace input hub. Planter section does not reengage while planter is moving forward. Spring in actuator arm not strong enough to push arm operational switch is turned to the ON position. Remove spring from inside solenoid and stretch spring slightly or replace. Reinstall spring. If that fails, file the away from stop collar when stop on the stop collar slightly so that the stop is not as aggressive. Frequent solenoid burnout. Fuses too large. Replace fuses on front panel with 0 amp slow blow fuses. Frequent fuse burnout. Low voltage ( volts required). Check power source voltage for partially discharged battery, etc. Damage to wiring harness. Repair or replace harness. Clutch or clutches will not disengage. Input and output shafts out of alignment. Input or output shaft is pushed in too far creating a coupler. Align input and output shafts to prevent drag. Reposition input and output shafts. 7 Rev. 0/

113 M0330 Troubleshooting PTO Pump Drive and Oil Cooler Option PROBLEM POSSIBLE CAUSE SOLUTION Pump is squealing. Lack of oil to pump. Check for plugged suction strainer. Check oil level. Oil temperature high. Low oil level. Check oil level and add as required. Desired fan speed cannot be Low oil level. Check oil level and add as required. achieved. Plugged filter. Check and change as required. Vacuum level not displayed. Digital vacuum gauge console power Turn ON. OFF. Cable not plugged in. Check connection. Digital vacuum gauge console has no power. Check fuse. Rev. 0/ 75

114 Troubleshooting M0330 Row Marker Operation PROBLEM POSSIBLE CAUSE SOLUTION Right marker lowering slower than left marker. Left marker lowering slower than right marker. Both markers lowering. Solenoid valve cartridge in port V not opening completely. Hose pinched or collapsed. Solenoid valve cartridge in port V not opening completely. Hose pinched or collapsed. Solenoid valve cartridge stuck open. If left marker switch is selected, right cartridge (V) is defective. If right marker switch is selected, left cartridge (V) is defective. Switch with cartridge in port V. If problem repeats, replace cartridge. Inspect hose routing. Replace or repair hoses as required. Switch with cartridge in port V. If problem repeats, replace cartridge. Inspect hose routing. Replace or repair hoses as required. Replace solenoid valve cartridge. Neither marker lowers. Blown fuse. Check red light on control console. It should be on if switch is on. If light is not on, switch to opposite marker position. If light comes on, switch may be defective. Replace switch. Otherwise replace fuse. Coils at V and V not energized. Marker flow control valve closed too far. Poor ground on wire, bad wire connection or damaged wire. Repair as required. See Row Marker Speed Adjustment. Neither marker will raise. Marker flow control valve closed too far. See Row Marker Speed Adjustment. Right marker will not lower. Solenoid coil in port V not energized. Check switch on control console. Replace if defective. Check coil ground wire. Check for poor connection or damaged wire. Solenoid cartridge in port V stuck closed. Switch cartridge with one on the planter you know is operating properly. If right marker lowers, replace defective cartridge. Left marker will not lower. Solenoid coil in port V not energized. Check switch on control console. Replace if defective. Check coil ground wire. Check for poor connection or damaged wire. Markers traveling too fast and damaging rubber stop on transport stands and/or damaging pivot at rod end of marker cylinders. Solenoid cartridge in port V stuck closed. Marker transport stand not adjusted correctly to allow marker cushion cylinders to operate as designed. Adjust row marker flow control valve. Switch cartridge with one on the planter you know is operating properly. If left marker lowers, replace defective cartridge. See Row Marker Transport Stand Adjustment. See Row Marker Speed Adjustment. 76 Rev. 0/

115 M0330 Troubleshooting Solenoid Valve PROBLEM POSSIBLE CAUSE SOLUTION No solenoids operate. Low voltage. Must be connected to volt DC only. Negative ground. One solenoid valve will not operate. Valve operating when not energized. Blown fuse. Battery connection. Wiring harness damaged. Bad switch. Cut wire in harness. Bad coil. Poor connection at coil. Valve stem stuck open. Oring leaking. Foreign material under poppet. Replace control console fuse with AGC5 amp. Clean and tighten. Repair or replace. Replace on control panel. Locate and repair. Replace. Check. Replace cartridge. Install new Oring kit. Remove and clean cartridge. Stroke Limiter Valve PROBLEM POSSIBLE CAUSE SOLUTION Planter will not raise. Planter will not stop at the raised field position. Poppet not moving freely in adapter and mechanical stop has poppet pushed completely in with no air gap. Mechanical stop arm not adjusted correctly. External leak. Worn or damaged Orings. Install seal kit. Remove adapter from valve block. Check movement of poppet in adapter. It should move freely. If not, remove poppet from adapter and clean seal area. Inspect poppet stem for damage. Adjust mechanical stop arm. Rev. 0/ 7

116 This page intentionally left blank.

117 MODEL 3700 FRONT FOLDING PLANTER PARTS MANUAL M0330 Rev. 9/ This manual applies to: Model: 3700 and 3700 ASD Front Folding Planters 00 Production and on Record the model number and serial number of your planter along with date purchased: Serial Number Date Purchased Information in this manual was current at time of printing. However, due to Kinze s ongoing product improvement, production changes may cause your machine to appear slightly different in detail. Kinze Manufacturing, Inc. reserves the right to change specifications or design without notice and without incurring obligation to install the same on machines previously manufactured. Right hand (R.H.) and left hand (L.H.), as used throughout this manual, are determined by facing in the direction the machine will travel when in use, unless otherwise stated. Kinze, the Kinze logo, TwinLine, Interplant, and EdgeVac are registered trademarks of Kinze Manufacturing, Inc.

118 Table Of Contents M0330 Row Unit Shank Assembly, Seed Tube, and Depth Adjustment... P Pneumatic Down Pressure Package Option...P3 Air Clutch, Pull Row Unit...P5 Parallel Arms, Mounting Support Plate, and Quick Adjustable Down Forces Springs Option P7 5" Seed Opener Disc Blade/Bearing Assembly and Scrapers...P9 Gauge Wheels P V Closing Wheels...P3 Hopper Support and Meter Drive...P5 Seed Hopper and Lid P7 Finger Pickup Seed Meter P9 BrushType Seed Meter P EdgeVac Seed Meter P3 Granular Chemical Hopper and Hopper Panel Extension...P5 Granular Chemical Meter and Meter Drive...P7 Granular Chemical Banding Options P9 Spring Tooth Incorporator...P3 Row Unit Mounted No Till Coulter...P3 Row Unit Mounted Disc Furrower...P33 Row Unit Mounted Residue Wheel...P35 Coulter Mounted Residue Wheels P37 Frame Mounted Coulter W/Residue Wheels...P39 EdgeVac System Vacuum System P Vacuum Fan Hydraulic Components...P3 Vacuum Fan Reservoir Assembly...P Reservoir Hose Supports/Clamps on Hitch...P5 Vacuum Fan Hydraulic Motor Assembly...P6 Vacuum Fan Motor Valve Block Assembly P7 Manifolds and Distribution Hoses, Row 30"... P9 Manifolds and Distribution Hoses, 36 Row 0"... P5 Vacuum Fan/Manifold Mounting Supports and Hardware...P53 PTO Pump Assembly P55 Air Seed Delivery System (ASD) ASD Fan System...P57 ASD Hydraulic Schematic...P59 ASD Hoses, Row 30"...P6 ASD Hoses, 36 Row 0"...P63 ASD Manifolds and Distribution Hoses...P65 ASD Entrainer Assembly, Row 30"... P67 ASD Entrainer Assembly, 36 Row 0"... P69 ASD Tank Assembly P7 ASD Scale Package P73 ASD Mechanical Row Unit P75 ASD Catwalk, Row 30" P77 ASD Catwalk, 36 Row 0" P79 ASD Stair, Row 30"...P8 Base Machine Front Hitch Assembly/Safety Chain P83 Hitch and Linkage Assembly, Row 0" P86 Hitch and Linkage Assembly, Row 30" and 36 Row 0"...P87 Front Hitch Assembly (Rear Section) P89 Front Wear Pads...P90 Tower Assembly, Row 0" P9 Tower Assembly, Row 30" and 36 Row 0"...P93 Stroke Limiter/Detent Valve Assembly and Linkage..... P95 Hinge and Wing Assemblies...P97 Hinge and Wing Assemblies...P98 Wing Frame, Row 30" P99 Wing Frame, 36 Row 0" P0 Hose TakeUp...P03 Axle and Transport Lockup...P05 Transport Wheel and Hub Assembly...P06 Wheel Module Assembly P07 Ground Drive Tire Assembly...P0 Contact Wheel Assembly P Point Row Clutch...P3 TwoSpeed Point Row Clutch P5 TwoSpeed Point Row Clutch Wheel Module Extensions P7 Airline Fittings and Hoses, Row 30"... P9 Airline Fittings and Hoses, 36 Row 0"... P0 Air Compressor and Dual Solenoid Assembly P3 Accumulator Assembly...P5 Seed Rate Transmission and Driveline...P7 Ratchet/Sprocket Assembly...P9 Row Marker Assembly...P30 Row Marker Spindle/Hub/Blade P33 Hydraulics Slave Cylinders...P35 Master Cylinder...P35 Hitch Paralled Linkage Cylinder P36 Assist Cylinder, 36 Row 0"... P37 Row Marker (Cushion) Cylinder P38 Helper Cylinder, All Sizes P39 Tongue Cylinder, Row 0" P0 i Rev. 9/

119 M0330 Table Of Contents Tongue Cylinder, Row 30" and 36 Row 0"...P Valve Block on Front Hitch P3 Valve Block on Tower Assembly P Valve Block on R.H. Wing... P5 Valve Block on L.H. Wing P7 Pilot Pressure Booster Valve Block...P8 Valve Block on L.H. and R.H. Wheel Module P8 Junction Block on Hose TakeUp...P9 Detent Lever Valve P50 Junction Block Located on L.H. Wing... P50 Stroke Limiter Valve P5 Pilot Operated Check Valve...P5 Solenoid Valve (GK76) P5 Solenoid Valve (GK75) P5 Pressure Relief Valves...P53 Check Valve...P53 Flow Control Valve P53 Clutch Valve Assembly...P5 ASD Valve Block...P55 Hydraulic System, Row 0" P57 Hydraulic System, Row 30" P59 Hydraulic System, 36 Row 0" P6 Electronics Electrical Components...P63 Light/Reflective Decal Brackets and Extensions...P66 KPM III Electronic Seed Monitor...P67 Planter Monitor Module (PMM)... P7 Kinze Cobalt Display...P73 Kinze Vision Display P75 Integra Display P77 Fertilizer Liquid Fertilizer Piston Pump Drive...P79 Liquid Fertilizer Piston Pump Mount and Ground Drive Wheel...P8 Liquid Fertilizer Hoses and Fittings...P83 Liquid Fertilizer Piston Pump, NGP P85 Liquid Fertilizer Piston Pump, NGP P87 Liquid Fertilizer Piston Pump Flow Divider...P89 Rear Trailer Hitch...P9 Decals, Paint, and Miscellaneous...P93 Numerical Index P06 Rev. 9/ ii

120 Vacuum System M0330 (A69/A56/GR736/A0765/A58/A699/A7856/A55/A839/A757) Vacuum Fan Assembly NOTE: Torque specifications in Maintenance Section. ITEM PART NO. QTY. DESCRIPTION G808X GD60 GA6975 GD89 GA56 GD630 GA996 Sending Unit W/¼" Tubing And Harness Tubing, ¼" x 5" Strain Relief 3 GR736 Hose Barb, ⅛" Male NPT To Barb GD5890 Clear Tube, 5 6" O.D. x 3 6" I.D. x 0" 5 GA0765 GR777 Analog Vacuum Gauge W/Hose Barb Hose Barb, ⅛" Male NPT To 3/6" Barb 6 GA0799 Breather, ⅛" Male NPT 7 G000 G387 G008 Hex Head Cap Screw, ⅜"6 x " Flat Washer, ⅜" SAE Lock Nut, ⅜"6 Backlite Control Console Assembly W/Mounting Brackets, Harness W/Dust Cap And Power Cable Mounting Bracket Knob Fuse, 5 Amp, Type AGC 8 G5 3 Hex Socket Head Cap Screw, No. 63 x ⅜", Grade 8 9 GD580 Mount 0 GD5803 Support GK3 Pin Female Connector Kit (Black), Includes: (3) Pin Female Housings, (6) Pin Contacts, (6) Seals GK30 Pin Male Connector Kit (Black), Includes: (3) Pin Male Housings, (6) Socket Contacts, (6) Seals 3 GD6608 Bracket GA69 Harness, 59", Row 30" And 36 Row 0" 5 GA838 Pin Female Connector Kit, Includes: () Pin Female Housing, () Seals, () Pin Contacts 6 GA839 Pin Male Connector Kit, Includes: () Pin Male Housing, () Seals, () Sockets P Rev. 9/

121 M0330 Vacuum System Digital Vacuum Gauge (Control Console) Sending Unit Analog Vacuum Gauge ITEM PART NO. QTY. DESCRIPTION 7 G66 6 Whiz Lock Bolt, ¼"0 x ¾" 8 GD680 Cover 9 GD699 Cover Gasket, ⅛" x 8⅜" (6½" I.D.) 0 G 7 Whiz Lock Bolt, ⅜"8 x " GA075 Cover G0063 G387 G008 Hex Head Cap Screw, ⅜"6 x " Flat Washer, ⅜" SAE Lock Nut, ⅜"6 3 GA097 Oil Cooler GA987 Screen 5 GD5790 Hub 6 GA0635 Impeller 7 GD5789 Backing Plate 8 G33 6 Hex Socket Head Cap Screw, 5 6"8 x ¾", Grade 8 9 G0599 G09 G00 Carriage Bolt, ⅜"6 x ¼" Lock Washer, ⅜" Hex Nut, ⅜"6 30 See Vacuum Fan Hydraulic Motor Assembly on page P6 3 GA08 Shroud 3 G009 G386 G009 Hex Head Cap Screw, 5 6"8 x " Flat Washer, 5 6" SAE Lock Nut, 5 6"8, Grade B 33 G39 G099 3 GD699 Gasket, ⅛" x ⅞" 35 GA65 Outlet, 3 6" GA57 Outlet, 35 6" 36 GD960 Stud, ⅜"6 G090 Lock Nut, ⅜"6 G387 Flat Washer, ⅜" SAE Flat Washer, ⅝" SAE Hex Jam Nut, ⅝"8, Grade 37 G600 GR67 Connector W/ORing, 6" Male JIC To ORing ORing 38 G650 Swivel Elbow, 5, 6" Male JIC To Female 39 GD6839 Spacer, ½" x " A GA757 Vacuum Fan Assembly (Items 3, 0, 3, and 33) Rev. 9/ P

122 Vacuum Fan Hydraulic Components M0330 (IP69) ITEM PART NO. QTY. DESCRIPTION See PTO Pump Assembly on page P55 See Vacuum Fan Reservoir Assembly on page P 3 See Vacuum Fan Motor Valve Block Assembly on page P7 See Vacuum Fan Motor Valve Block Assembly on page P7 5 *A800 Hose Assembly, ¼" x 3" 6 *A33 Hose Assembly, ⅝" x " 7 *A3 Hose Assembly, ⅝" x " 8 *A90 Hose Assembly, ¾" x 330" 9 *A05 Hose Assembly, ⅜" x 30" 0 *A338 Hose Assembly, ¾" x 6" *A39 Hose Assembly, ⅜" x " *A3 Hose Assembly, ⅝" x 3" 3 *A05 Hose Assembly, ⅜" x 36" * Hydraulic hose is not stocked by Kinze Repair Parts, but can be made available on a special order basis. Call for quote. P3 Rev. 9/

123 M0330 Vacuum Fan Reservoir Assembly (FF05a) ITEM PART NO. QTY. DESCRIPTION See Front Hitch Assembly (Rear Section) on page P89 GA3696 Reservoir 3 GD709 Liquid Level Sight GR83 Breather 5 G506 Elbow, 90, 6" Male JIC To " NPT 6 G50608 Plug, ¾" NPT Hex Head 7 G Elbow, 90, 9 6"8 Male JIC To ½" NPT 8 G5006 Elbow, 90, ⅝" Male JIC To " NPT 9 GA695 Mount 0 G007 G0 G0003 G GA697 Hose Guide Hex Head Cap Screw, ½"3 x ½" Lock Nut, ½"3 Hex Head Cap Screw, ⅜"6 x ½" Lock Nut, ⅜"6 Rev. 9/ P

124 Reservoir Hose Supports/Clamps on Hitch M0330 (FF05c) ITEM PART NO. QTY. DESCRIPTION G0980 G0 Hex Head Cap Screw, ½3 x 5½" Lock Nut, ½"3 GD070 Hose Clamp, ¾" x " x 3½" 3 GD70 Hose Clamp, " x 3" x ¾" GD888 Hose Clamp, ⅞" x 3" x 5⅜" 5 GD69 Support 6 G0006 G030 G39 G00 Hex Head Cap Screw, ⅝" x ¼" Lock Washer, ⅝" Flat Washer, ⅝" SAE Hex Nut, ⅝" 7 See Front Hitch Assembly/Safety Chain on page P83 P5 Rev. 9/

125 M0330 Vacuum Fan Hydraulic Motor Assembly (METRb) ITEM PART NO. QTY. DESCRIPTION GA09 Hydraulic Motor GR73 Seal Kit G6800 GR67 3 G600 GR67 Elbow W/ORing, 90, ⅞" Male JIC To 6" ORing ORing Connector W/ORing, 6" Male JIC To ORing ORing G Swivel Elbow, 90, 9 6"8 Male JIC To Female 5 G60006 GR05 Connector W/ORing, 9 6"8 Male JIC To ORing ORing Rev. 9/ P6

126 Vacuum Fan Motor Valve Block Assembly M0330 (FF07A907) L.H. Side Shown P7 Rev. 9/

127 M0330 Vacuum Fan Motor Valve Block Assembly ITEM PART NO. QTY. DESCRIPTION GD6873 Valve Block G6080 GR66 3 G6000 GR66 G608H060 GR05 5 G600 GR67 6 GA93 Relief Valve Cartridge 7 G60006 GR05 8 G68006 GR05 9 G6800 GR66 Plug W/ORing, ⅞" ORing ORing Connector W/ORing, ⅞" Male JIC To ORing ORing Hex Socket Head Plug W/ORing, 9 6"8 ORing ORing Connector W/ORing, 6" Male JIC To ORing ORing Connector W/ORing, 9 6"8 Male JIC To ORing ORing Elbow W/ORing, 90, 9 6"8 Male JIC To ORing ORing Elbow W/ORing, 90, ⅞" Male JIC To ORing ORing 0 G6500 Swivel Elbow, 5, ⅞" Male JIC To Female (L.H. Side Only) G65006 Swivel Elbow, 5, 9 6"8 Male JIC To Female (L.H. Side Only) G650 Swivel Elbow, 5, 6" Male JIC To Female (L.H. Side Only) 3 GA68 Pressure Compensating Element GD700 Adapter, ¼" NPT To ⅜" Barb 5 GA680 Cartridge 6 GA900 Coil W/Terminals 7 GA679 Relief Valve 8 GA0986 Motorized Flow Control 9 G680LL XLong Elbow W/ORing, 90, 6" Male JIC x 6" 0 G60 Connector W/ORing, 6" Female JIC x 6" GD6037 Oil Filter, 0 Micron GD6038 Filter Head 3 G600 GR67 Connector, W/ORing, 6" Male JIC To ORing ORing Rev. 9/ P8

128 Manifolds and Distribution Hoses, Row 30" M0330 (FF/IP6) Center Line of Planter Row Row Row 3 Row 5 Row 7 Row 9 Row Row 3 Row Row 6 Row 8 Row 0 Row Row L.H. Side of Planter P9 Rev. 9/

129 M0330 Manifolds and Distribution Hoses, Row 30" 6 Center Line of Planter w Row 3 Row 5 Row 7 Row 9 Row Row Row 6 Row 8 Row 0 Row Row 3 Row Row R.H. Side of Planter ITEM PART NO. QTY. DESCRIPTION G0676 Hose Clamp, No. 36, Stainless Steel GD66 3 Elbow, 90, " 3 See items 69 GD67 6 Coupler, " 5 G7 Cap, " 6 GD Pipe, 6" x 57½" 7 GD Pipe, 6" x " 8 GD Pipe, 6" x 7½" 9 GD58368 Pipe, 6" x 53½" 0 GD58363 Pipe, 6" x ½" GD58366 Pipe, 6" x 7" GA39 Manifold Flange, 9" 3 GA395 Manifold Flange, " GA39 Manifold Flange, " 5 GA393 Manifold Flange, 39¼" 6 GD Hose, " x 3" 7 GD Hose, " x 3" 8 GD5790 Hose, " x 36" 9 GD579 Hose, " x 0" 0 GD579 3 Hose, " x 6" GD705 Vacuum Plug Rev. 9/ P50

130 Manifolds and Distribution Hoses, 36 Row 0" M0330 (FF/IP6) Center Line of Planter Row Row Row 3 Row 5 Row 7 Row 9 Row Row 3 Row 5 Row 7 Row 9 Ro Row Row 6 Row 8 Row 0 Row Row Row 6 Row 8 Row 0 L.H. Side of Planter P5 Rev. 9/

131 M0330 Manifolds and Distribution Hoses, 36 Row 0" Center Line of Planter Row 9 Row Row 8 Row 0 Row Row 3 Row Row 5 Row 6 Row 7 Row 9 Row 3 Row 33 Row 35 Row 8 Row 30 Row 3 Row 3 Row 36 R.H. Side of Planter ITEM PART NO. QTY. DESCRIPTION G0676 Hose Clamp, No. 36, Stainless Steel GD66 3 Elbow, 90, " 3 See items 8 GD67 6 Coupler, " 5 G7 Cap, " 6 GD Hose, " x 3" 7 GD5856 Hose, " x 6" 8 GD5856 Pipe, 6" x ½" 9 GD5856 Hose, " x 58" 0 GD58565 Pipe, 6" x 3" GD5856 Pipe, 6" x 5½" GD58560 Pipe, 6" x ¼" 3 GD58560 Pipe, 6" x " GA00 Manifold Flange, 9¼" 5 GA0 Manifold Flange, 0" 6 GA999 Manifold Flange, 9" 7 GA998 Manifold Flange, 9¾" 8 GD Hose, " x 3" 9 GD Hose, " x 3" 0 GD Hose, " x 36" GD579 Hose, " x 0" GD579 Hose, " x 6" 3 GD705 Vacuum Plug Rev. 9/ P5

132 Vacuum Fan/Manifold Mounting Supports and Hardware M0330 (FF08bb) P53 Rev. 9/

133 M0330 Vacuum Fan/Manifold Mounting Supports and Hardware ITEM PART NO. QTY. DESCRIPTION See Vacuum System on page P See Manifolds and Distribution Hoses, Row 30" on page P9 See Manifolds and Distribution Hoses, 36 Row 0" on page P5 3 G003 G00 Hex Head Cap Screw, ¼"0 x ¾" Lock Nut, ¼"0, Grade B GD68 Manifold Gasket, ⅛" x 8 ⅜" (6⅝" I.D.) 5 G99 GD GA38 Support 7 G03 G05 8 G057 G007 Whiz Lock Bolt, ⅜"6 x " Sleeve, " Long 9 GD868 Tap Plate, Short 0 GD866 Support GD585 Clamp G0338 G060 Hex Head Cap Screw, ⅝" x 8" Hex Head Cap Screw, ⅝" x 9" Carriage Bolt, ½"3 x ¼" Serrated Flange Nut, ½"3 Carriage Bolt, 5 6"8 x ¼" Serrated Flange Nut, 5 6"8 3 G5 TBolt Clamp, 7" G033 G03 G006 Hex Head Cap Screw, 5 6"8 x ½" Lock Washer, 5 6" Hex Nut, 5 6"8 5 GA6 Mount 6 GD86 Tap Block 7 GA303 Offset Support 8 GD865 Offset Support 9 GD867 Tap Block, Long 0 GD86 Block Support Plate GD88930 Sleeve, 93 6" Long G0980 GD863 3 G57 G008 G0063 G0753 G09 G00 5 G000 G008 Hex Head Cap Screw, ½"3 x 5½" Cap Screw, ½"3 x 7" Hex Head Cap Screw, ⅜"6 x ½" Lock Nut, ⅜"6 Hex Head Cap Screw, ⅜"6 x " Hex Head Cap Screw, ⅜"6 x ½" Lock Washer, ⅜" Hex Nut, ⅜"6 Hex Head Cap Screw, ⅜"6 x " Lock Nut, ⅜"6 Rev. 9/ P5

134 PTO Pump Assembly M0330 (IP06/FF05c) ITEM PART NO. QTY. DESCRIPTION GA3793 PTO Pump G6800 Elbow W/ORing, 90, ⅝" Male JIC To ORing GR787 ORing 3 G680 Elbow W/ORing, 90, 6" Male JIC To ORing GR67 ORing G6 Hex Head Cap Screw, ½3, Grade 8 5 A397 Pump Storage 6 G0003 Hex Head Cap Screw, ⅜"6 x ½" 7 G008 Lock Nut, ⅜"6 8 See Front Hitch Assembly/Safety Chain on page P83 9 See Front Hitch Assembly/Safety Chain on page P83 A GR96 Seal Kit P55 Rev. 9/

135 This page left blank intentionally.

136 ASD Fan System M0330 (IP30) 6 ASD Fan Assembly Sending Unit Analog Pressure Gauge P57 Rev. 9/

137 M0330 ASD Fan System ITEM PART NO. QTY. DESCRIPTION GR97 Flanged Inner Case GR970 Flanged Outer Case 3 GR967 Screen GR976 Hex Flange Self Tapping Screw, ¼ x ¾ 5 GR977 6 Fender Washer, ¼ 6 GR978 Plastic Plug, ¼ 7 GR979 Plastic Plug, GR96 Bushing, ⅝ 9 G09 5 Hex Serrated Flanged Cap Screw, ¼ 0 x 0 G06 5 Serrated Flange Nut, ¼ 0 GR969 Backing Plate GR968 Cover Plate 3 G3 Hex Serrated Flange Cap Screw, ⅜ 6 x ¾ GA575 Overhung Load Adapter 5 G Hex Serrated Flange Cap Screw, ⅜ 6 x 6 G680 Elbow W/ORing, 90, 6 Male JIC To ORing 7 G6800 Elbow W/ORing, 90, ⅞ Male JIC To 6 ORing 8 G60006 Connector W/ORing, Male JIC To ORing 9 GA57 Hydraulic Motor 0 GD300 Key Stock, 3/6" x ¾" GD5890 Clear Plastic Tubing, 5 6" O.D. x 3 6" I.D. x 0" GA0765 GR777 Analog Vacuum Gauge W/Hose Barb Hose Barb, ⅛" Male NPT To 3 6" Barb 3 GA0799 Breather, ⅛" Male NPT G000 G008 Hex Head Cap Screw, ⅜"6 x " Lock Nut, ⅜"6 5 G5 3 Hex Socket Head Cap Screw, No. 63 x ⅜", Grade 8 6 GD580 Mount 7 GD595 Support 8 GA87 GD750 GA996 Low Pressure Sensor (00 IN H0) Tubing, ¼" x 0' Strain Relief 9 GR736 Hose Barb, ⅛" Male NPT To Barb 30 GA8 Hall Effect Adapter 3 GR000 Hydraulic Motor Key A GR960 ASD Fan Motor Seal Kit B GA573 ASD Fan Assembly (Flanged) (Items 7 and 9) Rev. 9/ P58

138 ASD Hydraulic Schematic M0330 (IP30) P59 Rev. 9/

139 M0330 ASD Hydraulic Schematic ITEM PART NO. QTY. DESCRIPTION See ASD Fan System on page P57 See ASD Fan System on page P57 3 *A500 Hose Assembly, ⅜" x 0" *A3368 Hose Assembly, ¾" x 86" 5 *A87 Hose Assembly, ½" x 86" 6 *A3353 Hose Assembly, ¾" x 33" 7 *A Hose Assembly, ½" x 30" *Hydraulic hose is not stocked by Kinze Repair Parts, but can be made available on a special order basis. Call for quote. Rev. 9/ P60

140 ASD Hoses, Row 30" M0330 (IP) R.H. Rear of Machine Air in R.H. Entrainment 5 ITEM PART NO. QTY. DESCRIPTION GA3800 Seed Hose Assembly, ¼" x 8" GA380 Seed Hose Assembly, ¼" x 9" 3 GA380 Seed Hose Assembly, ¼" x 6" GA3803 Seed Hose Assembly, ¼" x 33" 5 GA380 Seed Hose Assembly, ¼" x 0" 6 GA380 Seed Hose Assembly, ¼" x 5" 7 GA387 Seed Hose Assembly, ¼" x 6" 8 GA388 Seed Hose Assembly, ¼" x 80" 9 GA389 Seed Hose Assembly, ¼" x 33" 0 GA380 Seed Hose Assembly, ¼" x 30" GA38 Seed Hose Assembly, ¼" x 37" GA38 Seed Hose Assembly, ¼" x 03" 3 GA383 Seed Hose Assembly, ¼" x 8" GB05 Dissipator Quick Coupler 5 GB09 Seed Entrainer Quick Coupler P6 Rev. 9/

141 M0330 ASD Hoses, Row 30" L.H. Rear of Machine Air in L.H. Entrainment Rev. 9/ P6

142 ASD Hoses, 36 Row 0" M0330 (IP53) R.H. Rear of Machine Air In R.H. Entrainment 3 ITEM PART NO. QTY. DESCRIPTION GA3800 Seed Hose Assembly, ¼" x 8" GA380 Seed Hose Assembly, ¼" x 9" 3 GA380 Seed Hose Assembly, ¼" x 6" GA3803 Seed Hose Assembly, ¼" x 33" 5 GA380 Seed Hose Assembly, ¼" x 0" 6 GA38 Seed Hose Assembly, ¼" x 03" 7 GA385 Seed Hose Assembly, ¼" x 6" 8 GA388 Seed Hose Assembly, ¼" x 80" 9 GA389 Seed Hose Assembly, ¼" x 33" 0 GA380 Seed Hose Assembly, ¼" x 30" GA38 Seed Hose Assembly, ¼" x 37" GA38 Seed Hose Assembly, ¼" x 03" 3 GA383 Seed Hose Assembly, ¼" x 8" GA386 Seed Hose Assembly, ¼" x 76" 5 GA387 Seed Hose Assembly, ¼" x 35" 6 GA388 Seed Hose Assembly, ¼" x 6" 7 GA389 Seed Hose Assembly, ¼" x 30" 8 GA3830 Seed Hose Assembly, ¼" x 30" 9 GA383 Seed Hose Assembly, ¼" x 380" 0 GA383 Seed Hose Assembly, ¼" x 38" GA3833 Seed Hose Assembly, ¼" x 50" GB05 Dissipator Quick Coupler 3 GB09 Seed Entrainer Quick Coupler P63 Rev. 9/

143 M0330 ASD Hoses, 36 Row 0" L.H. Rear of Machine Air In L.H. Entrainment Rev. 9/ P6

144 ASD Manifolds and Distribution Hoses M0330 (IP70) P65 Rev. 9/

145 M0330 ASD Manifolds and Distribution Hoses ITEM PART NO. QTY. DESCRIPTION GA08 GD8306 G007 Fan Mount UBolt, 7" x 5" x ½"3 Serrated Flange Nut, ½"3 GA337 G09 G000 GR777 3 GA3 G0 G GA08 Tank Frame 5 GA05 G000 G09 6 GA6700 G06 G006 7 GA670 G06 G006 8 GD095 G0686 G09 9 GD096 G0305 G09 0 GD09 G0305 G09 GA6699 G06 G006 G05 GD69 G0 3 GD075 G39 G08 GA078 GA8 8 8 See ASD Fan System on page P57 Serrated Flange Nut, ⅜"6 Hex Head Cap Screw, ⅜"6 x " Hose Barb, ⅛" Male NPT To 3 6" Barb ASD Fan Block Washer, ¼" SAE Hex Head Cap Screw, ¼"0 x 3¼" Light Bracket Hex Head Cap Screw, ⅜"6 x ¼" Serrated Flange Nut, ⅜"6 See Electrical Components on page P63 Serrated Flange Nut, ¼"0 Hex Head Cap Screw, ¼"0 x " See Electrical Components on page P63 Serrated Flange Nut, ¼"0 Hex Head Cap Screw, ¼"0 x " Mounting Bracket Hex Head Cap Screw, ⅜"6 x 8" Serrated Flange Nut, ⅜"6 Clean Out Chute Clip Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 Clean Out Chute Plate Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 See Electrical Components on page P63 Serrated Flange Nut, ¼"0 Hex Head Cap Screw, ¼"0 x " Hex Head Cap Screw, ¾"0 x " Special Washer, 5 3" I.D. x ¼" O.D., Hardened Lock Nut, ¾"0 Eye Bolt, " x " Flat Washer, " SAE Lock Nut, " Cleanout Chute, Row Cleanout Chute, 36 Row 5 GD Hose, ½" x 9" 6 G360 TBolt Hose Clamp, ½" Rev. 9/ P66

146 ASD Entrainer Assembly, Row 30" M0330 (IP) R.H. Shown P67 Rev. 9/

147 M0330 ASD Entrainer Assembly, Row 30" ITEM PART NO. QTY. DESCRIPTION GB033 3 ASD Seed Entrainer Door Section GD985 G055 3 GB03 GD ASD Cleanout Door Hinge Rod, Row Cotter Pin, 6" x ½" ASD Small Cap (If Applicable) Small ORing GD9698 ASD Chute Hanger, R.H. 5 GA9 ASD Shutoff Door 6 GB050 GD Latch Handle Eye Bolt, ¼"0 x.83" 7 GD080 6 Cam Nut, ¼"0 8 GB050 3 ASD Cleanout Door 9 GD9863 ASD Cleanout Door Gasket, Row 0 GD9699 ASD Chute Hanger, L.H. GD985 G38 G003 GB036 GB035 0 Hex Head Cap Screw, ¼"0 x " Washer, ¼" Lock Nut, ¼"0, Grade B ASD Seed Entrainer Air Inlet, R.H. (Shown) ASD Seed Entrainer Air Inlet, L.H. 3 GD9635 ASD Retainment Ring G036 G053 5 G099 G33 G30 6 GB0 ASD Shutoff Door Plug 7 GD9695 ASD Slide Latch 8 GD9665 ASD Spacer Plate 9 GB07 9 ASD Seed Entrainer 0 GD9865 G Carriage Bolt, ¼"0 x " Wing Nut W/Nylon Insert, ¼"0 Serrated Flange Nut, No. 0 Hex Socket Head Set Screw, ¼" x No. 0 x ⅜" Hex Nut, ¼"0 Eye Bolt, ¼"0 x.7" Serrated Flange Nut, ¼"0 GB03 ASD Seed Entrainer End Cap GD9808 G000 G06 3 GA8 Cleanout Chute GB030 ASD Large Cap 3 3 Cleanout Chute Storage Bracket Hex Head Cap Screw, ⅜"6 x " Serrated Flange Nut, ⅜"6 A GA00 ASD Entrainer Assembly, R.H. (Shown) (Items ) B GA005 ASD Entrainer Assembly, L.H. (Items ) Rev. 9/ P68

148 ASD Entrainer Assembly, 36 Row 0" M0330 (IP7) P69 Rev. 9/

149 M0330 ASD Entrainer Assembly, 36 Row 0" ITEM PART NO. QTY. DESCRIPTION GB033 ASD Seed Entrainer Door Section GD9855 G055 ASD Cleanout Door Hinge Rod, 8 Row Cotter Pin, 6 x ½ 3 GD9698 ASD Chute Hanger, R.H. GD05 ASD Shutoff Door 5 GB050 GD Latch Handle Eye Bolt, ¼ 0 x.83 6 GD080 9 Cam Nut, ¼ 0 7 GD86 ASD Cleanout Door, Half 8 GD00 ASD Cleanout Door Gasket, 8 Row 9 GD9699 ASD Chute Hanger, L.H. 0 GD9853 G38 G003 GB036 GB035 0 Hex Head Cap Screw, ¼ 0 x 3 ½ Washer, ¼ Hex Nut, ¼ 0 ASD Seed Entrainer Air Inlet, R.H. (Shown) ASD Seed Entrainer Air Inlet, L.H. GD9635 ASD Retainment Ring 3 GB07 ASD Seed Entrainer GD9665 ASD Spacer Plate 5 G053 G036 6 G099 G33 7 GB0 ASD Shutoff Door Plug 8 GD9695 ASD Slide Latch 9 G06 GD Wing Nut W/Nylon Insert, ¼ 0 Carriage Bolt, ¼ 0 x Serrated Flange Nut, No. 0 Hex Socket Head Set Screw, ¼ x No. 0 x ⅜ Serrated Flange Nut, ¼ 0 Eye Bolt, ¼ 0 x.7 0 GB03 ASD Seed Entrainer End Cap GB050 ASD Cleanout Door A GA08 ASD Entrainer Assembly, R.H. (Shown) (Items ) B GA09 ASD Entrainer Assembly, L.H. (Items ) Rev. 9/ P70

150 ASD Tank Assembly M0330 (IP5) P7 Rev. 9/

151 M0330 ASD Tank Assembly ITEM PART NO. QTY. DESCRIPTION GD989 ASD Tank GD08 GD0 3 GA09 G059 G0053 G0 GA707 GA089 GD00 GD0030 G038 G387 ASD Tank Lid Seal Foam Seal Connector ASD Lid Rim Hair Pin Clip, No. Hex Head Cap Screw, ½ 3 x ½ Lock Nut, ½ 3 ASD Lid Assembly (also includes item no. ) Latch Handle Latch Mount Bracket Pivot Bail Bracket Hex Head Cap Screw, ⅜ 6 x ⅝ Flat Washer, ⅜ SAE 5 GA037 ASD Rear Tank Frame 6 GD09 Entrainer Mount Tap Block, Long 7 GD093 Entrainer Mount Tap Block, Short 8 GA038 ASD Front Tank Frame 9 GA00 GD0037 G00 G000 0 GD9956 GD9958 GD9893 GD000 GD GD96900 G0 G007 G39 ASD Rear Tank Mount Pin, x 5⅜ Special Washer, ⅜ x ½ O.D. Hex Head Cap Screw, ⅜ 6 x ASD Entrainment Mounting Plate, Row (Shown) ASD Entrainment Mounting Plate, 8 Row ASD Tank Mount Gasket, Row ASD Tank Mount Gasket, 8 Row Ribbon Sealer, 6½ Ribbon Sealer, 7 Flanged Whiz Lock Screw, ⅜ 6 x ¼, Serrated Hex Head Cap Screw, ¾ 0 x ½ Flat Washer, ¾ SAE See ASD Entrainer Assembly, Row 30 on page P68 See ASD Entrainer Assembly, 36 Row 0 on page P69 3 G035 G008 GA50 3 ASD Tank Mount 5 GD0035 Pin, ½ x ¼ 6 GD0036 Pin, ½ x 7 7 GD08 G000 G09 3 Hex Head Cap Screw, ⅜ 6 x ¾ Lock Nut, ⅜ 6 Seed Hose Strap Bracket Hex Head Cap Screw, ⅜ 6 x Serrated Flange Nut, ⅜ 6 8 G030 Carriage Bolt, ⅜ 6 x ½ 9 GA839 Clamp Ring 0 GD7 Outer Clamp Ring G 8 Hex Serrated Flange Cap Screw, ⅜ 6 x ¾ GD308 Bolt Holder 3 GA5 Seed Hose Strap A GA003 ASD Tank Assembly, Row (Items and 9) B GA36 ASD Tank Assembly, 8 Row (Items and 9) Rev. 9/ P7

152 ASD Scale Package M0330 (IP9) P73 Rev. 9/

153 M0330 ASD Scale Package ITEM PART NO. QTY. DESCRIPTION GA35 6 Load Cell GA36 Scale Module 3 GA9 Power Cable GA33 ASD Scale Display 5 GD08 Scale Module Mounting 6 G0857 Hex Head Cap Screw, ¼"0 x ¼" 7 G003 Hex Head Cap Screw, ¼"0 x ¾" 8 G06 Serrated Flange Nut, ¼"0 9 GA03 Mounting Bracket Assembly, Includes: () Mounting Brackets, () Connector Halves, () Compression Spring, () Tension Knob, () ¼"0 x ¾" Hex Head Cap Screw, () ¼" Plastic Washer, () ¼" Steel Washer 0 GD08 G8 UBolt, #03 Serrated Flange Nut, #03 G6 Phillips Pan Head Machine Screw, No. 03 x ½", Stainless Steel Rev. 9/ P7

154 ASD Mechanical Row Unit M0330 (IP56) P75 Rev. 9/

155 M0330 ASD Mechanical Row Unit ITEM PART NO. QTY. DESCRIPTION See Shank Assembly, Seed Tube, and Depth Adjustment on page P See Parallel Arms, Mounting Support Plate, and Quick Adjustable Down Forces Springs Option on page P7 See Hopper Support and Meter Drive on page P5 GA05 Meter Drive Assembly Complete, /9 Tooth 3 G0338 Carriage Bolt, 5 6"8 x ¼" G060 Serrated Flange Nut, 5 6"8 5 GA957 Mini Hopper 6 GB033 GA03 Clutch Adapter Plate ASD Mechanical Meter Cover 7 GB06 ASD MechanicalMeter Cover Seal 8 GB05 ASD Mechanical Meter Cover 9 GB055 ASD Air Pressure Dissipator 0 GB057 Air Dissipator Screen G000 Hex Head Cap Screw, ⅜"6 x ¼" GD003 Knob, 5 6"8 x ¼" 3 GB030 ASD Large Cap GD9509 ORing, Large Rev. 9/ P76

156 ASD Catwalk, Row 30" M0330 (IP7) P77 Rev. 9/

157 M0330 ASD Catwalk, Row 30" ITEM PART NO. QTY. DESCRIPTION See ASD Tank Assembly on page P7 G030 G09 3 GA0 G000 G09 G0306 G09 5 GD997 G0305 G09 G0636 G GA07 Catwalk 7 GA080 G0305 G09 8 GA079 G0305 G09 9 GA097 G0305 G09 0 GD997 G0037 G007 G0305 G Carriage Bolt, ⅜"6 x ½" Serrated Flange Nut, ⅜"6 Hose Hanger Hex Head Cap Screw, ⅜"6 x " Serrated Flange Nut, ⅜"6 Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 Rear Catwalk Mount Plate Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 Carriage Bolt, ½"3 x ½" Serrated Flange Nut, ½"3 R.H. Handrail Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 L.H. Handrail Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 Front Handrail Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 Front Catwalk Mount Plate Hex Head Cap Screw, ½"3 X ¼" Serrated Flange Nut, ½"3 Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 Rev. 9/ P78

158 ASD Catwalk, 36 Row 0" M0330 (IP80) P79 Rev. 9/

159 M0330 ASD Catwalk, 36 Row 0" ITEM PART NO. QTY. DESCRIPTION GA097 G0305 G09 Front Handrail Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 See ASD Tank Assembly on page P7 3 G030 Carriage Bolt, ⅜"6 x ½" G09 GD997 G0037 G007 G0305 G09 5 GD997 G0636 G007 G0305 G09 6 GA3 G0305 G Serrated Flange Nut, ⅜"6 Front Catwalk Mount Plate Hex Head Cap Screw, ½"3 X ¼" Serrated Flange Nut, ½"3 Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 Rear Catwalk Mount Plate Carriage Bolt, ½"3 x ½" Serrated Flange Nut, ½"3 Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 Rear L.H. Handrail Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 7 GA Rear Catwalk 8 GA3 G0005 GB08 G007 Lock Nut, ⅝" 9 GA G387 G0305 G09 G05 GA0 0 GD05 G05 GA GD5857 G078 G39 G006 G007 GD3803 GA G0305 G09 3 GD0356 G0305 G Ladder Hex Head Cap Screw, ⅝ x ¾" Bushing, 3" I.D. x ⅞" O.D. x 9 3" Long Latch Handle Flat Washer, ⅜" SAE Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 Cotter Pin, ⅛" x " Latch Mount Latch Stabilizer Cotter Pin, ⅛" x " Latch Spring Clevis Pin, 5 6" x " Flat Washer, ⅝" SAE Hex Head Cap Screw, ⅝" x 5" Lock Nut, ⅝" Sleeve, ⅞ O.D. x ½" Front R.H. Handrail Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 Ladder Latch Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 GA6 Front Catwalk 5 GD070 G0305 G09 6 GD9505 G060 7 GA5 G0305 G09 8 GA G0305 G09 9 GA0 G000 G Latch Plate Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 Pin, ¼" x ¾" Cotter Pin, ¼" x " Front L.H. Handrail Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 Rear R.H. Handrail Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 Hose Hanger Hex Head Cap Screw, ⅜"6 x " Serrated Flange Nut, ⅜"6 Rev. 9/ P80

160 ASD Stair, Row 30" M0330 (IP73) 3 ITEM PART NO. QTY. DESCRIPTION GA07 Step Bracket GD086 G00 G030 3 GB035 3 Step GD7 G0 G389 6 UBolt, 7" x 7" x ⅝" Hex Nut, ⅝" Lock Washer, ⅝" UBolt, " x " x ½"3 Lock Nut, ½"3 Flat Washer, ½" SAE P8 Rev. 9/

161 This page left blank intentionally.

162 Front Hitch Assembly/Safety Chain M0330 (WGN7a/FF90a/A966/A966/FF93/FF) P83 Rev. 9/

163 M0330 Front Hitch Assembly/Safety Chain ITEM PART NO. QTY. DESCRIPTION GA9856 GK3 Safety Chain, ⅝" Safety Chain Repair Kit, Includes: () Hook, () Flat Washer, () Latch Pin, () Safety Latch, () Spring, () Retaining Ring G00 G057 Hex Head Cap Screw, ¼"7 x 6½" Lock Nut, ¼"7 3 GB036 Single Clevis, Swivel Hitch GA956 G063 5 GD939 Hose Holder 6 G0006 G030 G39 G00 7 G05 G GD3377 Spindle 9 GA959 Hitch Cap 0 GA989 G060 GA003 G060 G68008 GR037 3 G075 G03 G006 Swivel Block W/Grease Fitting Grease Fitting, 5, ¼"8 Hex Head Cap Screw, ⅝" x ¼" Lock Washer, ⅝" Flat Washer, ⅝" SAE (If Applicable) Hex Nut, ⅝" Hex Head Cap Screw, "8 x 6" Lock Nut, "8 Upper Hitch Link W/Grease Fittings Grease Fitting, ¼"8 Lower Hitch Link W/Grease Fittings Grease Fitting, ¼"8 Elbow W/ORing, 90, ¾"6 Male JIC To ORing ORing Hex Head Cap Screw, 5 6"8 x 8" Lock Washer, 5 6" Hex Nut, 5 6"8 See Valve Block on Front Hitch on page P3 5 See Front Hitch Assembly (Rear Section) on page P89 6 GD0705 Locking Clip Pin, ¼" x ½" 7 G009 G03 G006 8 GA965 Handle Mount 9 GD960 G075 0 GD067 G060 GD0 G060 GR077 GR093 8 Hex Head Cap Screw, 5 6"8 x " Lock Washer, 5 6" Hex Nut, 5 6"8 Pin, ½" x ¼" Spring Pin, ¼" x ¼" Pin, ¼" x 0¾" Cotter Pin, ¼" x " Pin, ¼" x " Cotter Pin, ¼" x " Pin W/Clip Hair Pin Clip 3 See Hitch Paralled Linkage Cylinder on page P36 GA683 GD7 Parallel Linkage Lock Pin Tab Lock Pin, 7 6" x ½" 5 G03 Shim 6 GD3605 Output Spur Gear 7 G09 GD307 G057 Hex Head Cap Screw, ¼"7 x 3½" Washer, 3¾" Lock Nut, ¼"7 8 G0 Cover 9 GA9655 Handle 30 GA966 Speed Jack Assembly, Less Handle And Foot Assembly Rev. 9/ P8

164 Front Hitch Assembly/Safety Chain M0330 ITEM PART NO. QTY. DESCRIPTION 3 G076 Spring Pin, M0 x 50 (Metric) 3 G0006 G030 G00 33 GA966 G03 G0 Hex Head Cap Screw, ⅝" x ¼" Lock Washer, ⅝" Hex Nut, ⅝" Jack Foot Assembly W/Hardware Hex Head Cap Screw, ½"3 x 7" Lock Nut, ½"3 3 GA9663 Lower Leg Assembly 35 GD3598 Collar 36 GA9665 Thrust Bearing 37 G080 Dowel Pin, ⅜" x ¾" 38 GD3600 Thrust Washer 39 GD360 Bevel Gear 0 GD360 Output Cluster Gear G030 Spring Pin, ⅜" x ¾" GD3603 Output Shaft 3 G03 Spring Pin, 5 6" x ½" G0960 Flanged WhizLock Screw, ¼"0 x ⅝", No Serration 5 GD3607 Cover 6 GD3606 Input Spur Gear 7 GD3608 Output Shaft 8 GA99 Shaft Housing Assembly 9 G009 G009 Hex Head Cap Screw, 5 6"8 x " Lock Nut, 5 6"8, Grade 8 50 G06 Grease Fitting, ⅛" NPT 5 GD360 3 Bushing 5 G007 G08 Hex Head Cap Screw, ½"3 x ½" Lock Washer, ½" 53 GD5785 Mount, ½" x 5½" 5 GD5787 Stop Block, ½" x 8" 55 GD36 Input Shaft 56 GD3609 Detent Ball 57 GD360 Detent Spring A GA950 Speed Jack/Mount SubAssembly (Items 9, 30, 3 And 33) B G7786x Safety Chain Package (Items: and 7) P85 Rev. 9/

165 M0330 Hitch and Linkage Assembly, Row 0" (FF6) ITEM PART NO. QTY. DESCRIPTION See Front Hitch Assembly/Safety Chain on page P83 See Tongue Cylinder, Row 0" on page P0 3 See Front Wear Pads on page P90 GA776 GD030 G083 GA GA775 GD030 G083 GA GA790 Stop 7 GD3 G030 G00 8 GD3 G060 8 R.H. Draft Link W/Split Locking Nut, Socket Head Screw And Joint, Row 0 Split Locking Nut, ", Grade Socket Head Screw, ¼"0 x ⅝" Joint L.H. Draft Link W/Split Locking Nut, Socket Head Screw And Joint, Row 0 Split Locking Nut, ", Grade Socket Head Screw, ¼"0 x ⅝" Joint UBolt, 5" x 7" x ⅝" Lock Washer, ⅝" Hex Nut, ⅝" Pin, ¼" x 8¾" Cotter Pin, ¼" x " 9 See Hinge and Wing Assemblies on page P98 0 GD5506 G060 Pin, ¼" x 6" Cotter Pin, ¼" x " A773 Rear Hitch (NonStock Item) Rev. 9/ P86

166 Hitch and Linkage Assembly, Row 30" and 36 Row 0" M0330 (TP06) P87 Rev. 9/

167 M0330 Hitch and Linkage Assembly, Row 30" and 36 Row 0" ITEM PART NO. QTY. DESCRIPTION See Front Wear Pads on page P90 See Hinge and Wing Assemblies on page P97 3 See Tongue Cylinder, Row 30" and 36 Row 0" on page P GA753 GD030 G083 GA GD9503 G060 6 GA665 Axle Link 7 GD3 G060 L.H. Draft Link W/Split Locking Nut, Socket Head Screw And Joint Split Locking Nut, ", Grade Hex Socket Head Screw, ¼"0 x ⅝" Joint Pin, ¼" x 6⅛" Cotter Pin, ¼" x " Pin, ¼" x 8¾" Cotter Pin, ¼" x " 8 See Tower Assembly, Row 30" and 36 Row 0" on page P93 9 GD950 G060 Pin, ¼" x 5" Cotter Pin, ¼" x " 0 See Tower Assembly, Row 30" and 36 Row 0" on page P93 A70 Rear Hitch (NonStock Item) GD5506 G060 3 GA75 GD030 G083 GA6660 G060 Cotter Pin, ¼" x " Pin, ¼" x 6" Cotter Pin, ¼" x " R.H. Draft Link W/Split Locking Nut, Socket Head Screw And Joint Split Locking Nut, ", Grade Hex Socket Head Screw, ¼"0 x ⅝" Joint Rev. 9/ P88

168 Front Hitch Assembly (Rear Section) M0330 (IP306) ITEM PART NO. QTY. DESCRIPTION A700 A8973 Front Hitch, 99 ⅝" (NonStock Item), Row 30" Front Hitch, 66 ⅝" (NonStock Item), Row 0" GD9366 Roller 3 GD9367 Sleeve GD000 Bronze Adjusting Plug 5 GD936 Mounting Pin 6 G0769 Spring Pin, ⅜" x ¾" 7 G0760 Hex Socket Set Screw, ⅜"6 x ½" P89 Rev. 9/

169 M0330 Front Wear Pads (IP305) ITEM PART NO. QTY. DESCRIPTION GD967 Cap GD968 Bearing Pad 3 GD965 Shim, ⅜" GD998 Shim, Gauge 5 GD098 Shim, ¼" (As Required) 6 GA6655 Retainer Pad 7 G0007 Hex Head Cap Screw, ⅝" x ½" 8 G030 Lock Washer, ⅝" 9 G0763 Grease Fitting, Extended, ⅛"7 Rev. 9/ P90

170 This page left blank intentionally.

171 M0330 Tower Assembly, Row 0" (FF63b) ITEM PART NO. QTY. DESCRIPTION G036 G09 G00 Hex Head Cap Screw, ⅜"6 x 3¾" Lock Washer, ⅜" Hex Nut, ⅜"6 See Valve Block on Tower Assembly on page P 3 See Hitch and Linkage Assembly, Row 0" on page P86 G68008 GR037 Elbow W/ORing, 90, ¾"6 Male JIC To ORing ORing 5 See Slave Cylinders on page P35 6 GD55 GD535 G098 7 GA897 GA83 8 GD585 G060 Pin, ¼" x 5 ½" Special Bushing, " O.D. x " I.D. x ¾" Long HD External Retaining Ring, " Cylinder Lockup Bracket W/Pin Assembly Pin W/Lynch Pin, 5½" Pin, ¼" x ½" Cotter Pin, ¼" x " Rev. 9/ P9

172 Tower Assembly, Row 30" and 36 Row 0" M0330 (IP58) P93 Rev. 9/

173 M0330 Tower Assembly ITEM PART NO. QTY. DESCRIPTION See Slave Cylinders on page P35 GD585 G060 GA897 Pin, ¼" x ½" Cotter Pin, ¼" x " Cylinder Lockup Bracket W/Pin Assembly 3 GA8963 Cylinder Lockup GA83 Pin W/Lynch Pin, 5½" 5 GD55 G098 Pin, ¼" x 5½" HD External Retaining Ring, " 6 GD535 Special Bushing, " O.D. x " I.D. x ¾" Long 7 GA0 Axle Mount 8 G03 9 GD968 8 Bearing Pad 0 GD998 3 Shim, Gauge GA595 G03 G05 G005 GD965 8 Shim, ⅜" 3 GD098 8 Shim, ¼" GA Retainer Pad 5 GD838 G0763 G005 G008 G03 G See Valve Block on Tower Assembly on page P Hex Head Cap Screw, ⅜"6 x 3¾" Retainer Lock Washer, ¾" Machine Bushing, ¾", Gauge Hex Head Cap Screw, ¾"0 x ½" Retainer, 8" x 8¾" Grease Fitting, Extended, ⅛"7 Hex Nut, ¾"0 Hex Head Cap Screw, ¾"0 x 3" Lock Washer, ¾" Hex Head Cap Screw, ¾"0 x ½" Rev. 9/ P9

174 Stroke Limiter/Detent Valve Assembly and Linkage M0330 PHA03(FF8e) P95 Rev. 9/

175 M0330 Stroke Limiter/Detent Valve Assembly and Linkage ITEM PART NO. QTY. DESCRIPTION GA666 GD88 GD999 G00 Rod Assembly Yoke Stud Hex Nut, ⅝" G08 G05 Clevis Pin, ½" x ½" Cotter Pin, ⅛" x " 3 GA6685 Cam Activator G0606 Spring Pin, ¼" x " 5 GA6687 Housing 6 GA6686 Cam 7 G00 Hex Socket Set Screw, ⅜"6 x ½" 8 GD95 Detent Arm 9 G008 G008 0 G GR037 Hex Head Cap Screw, ⅜"6 x " Lock Nut, ⅜"6 Elbow W/ORing, 90, ⅞" Male JIC To ¾"6 ORing ORing G65000 Swivel Elbow, 90, ⅞" Male JIC To Female G0009 G007 3 GA0 Bearing GD07 Spacer 5 G008 G00 Hex Head Cap Screw, ⅝" x ½" Lock Nut, ⅝" Hex Head Cap Screw, ⅜"6 x " Hex Nut, ⅜"6 6 See Detent Lever Valve on page P50 7 G60808 GR037 Plug W/ORing, ¾"6 ORing ORing 8 GA753 Stroke Limiter Arm (If Applicable) 9 G000 G09 G00 Hex Head Cap Screw, ⅜"6 x ¼" Lock Washer, ⅜" Hex Nut, ⅜"6 0 See Stroke Limiter Valve on page P5 G0069 G009 G386 G GR037 Hex Head Cap Screw, 5 6"8 x ¼" Lock Nut, 5 6"8 Flat Washer, 5 6" SAE Connector W/ORing, ⅞" Male JIC To ¾"6 ORing ORing Rev. 9/ P96

176 Hinge and Wing Assemblies M0330 PFA06/PFA05(FF9c) P97 Rev. 9/

177 M0330 Hinge and Wing Assemblies ITEM PART NO. QTY. DESCRIPTION G0 Lock Nut, ½"3 GD070 GD Hose Clamp, ¾" x " x 3½" Hose Clamp, ¾" x " x ½" 3 See Helper Cylinder, All Sizes on page P39 GD977 Spacer 5 GD936 Hose Guide 6 GD3803 Sleeve, ⅝" I.D. x ⅞" O.D. x " Long 7 GA660 Bracket 8 G00 G030 G00 9 G GR037 0 G006 G03 GD956 Pivot Washer G007 G08 G00 Hex Head Cap Screw, ⅝" x 5½" Lock Washer, ⅝" Hex Nut, ⅝" Elbow W/ORing, 90, 9 6"8 Male JIC To ¾"6 ORing ORing Hex Head Cap Screw, ¾"0 x " Lock Washer, ¾" Hex Head Cap Screw, ½"3 x ½" Lock Washer, ½" Hex Nut, ½"3 3 GA676 Pin GD38006 Sleeve, ⅝" I.D. x ⅞" O.D. x ¾" Long 5 G003 G0036 G030 G00 6 GA903 G759 7 GD99 SMV Sign 8 G00 G07 G003 Hex Head Cap Screw, ⅝" x 3½" Hex Head Cap Screw, ⅝" x " Lock Washer, ⅝" Hex Nut, ⅝" See Wing Frame, Row 30" on page P99 See Wing Frame, 36 Row 0" on page P0 L.H. Wing, 6⅜", Row 0" Hex Head Cap Screw, ¼"0 x ½" Lock Washer, ¼" Hex Nut, ¼"0 9 G0360 Machine Bushing, ½", 0 Gauge 0 GD96 6 Washer GA837 G060 GD963 Washer 3 G0057 G03 G005 GA899 G0360 G0359 GD69 5 GD976 G06 6 GA903 GA76 3 Knuckle Less Grease Fittings Grease Fitting, ¼"8 Hex Head Cap Screw, ¾"0 x 7" Lock Washer, ¾" Hex Nut, ¾"0 Vertical Pin Machine Bushing, ½", 0 Gauge (As Required) Machine Bushing, ½", 8 Gauge (As Required) Pin, ⅜" x 3½" Pin, ½" x 3⅛" Cotter Pin, ⅜" x 3" See Wing Frame, Row 30" on page P99 See Wing Frame, 36 Row 0" on page P0 R.H. Wing, 3⅜", Row 0" Rev. 9/ P98

178 Wing Frame, Row 30" M0330 (IP65) P99 Rev. 9/

179 M0330 Wing Frame, Row 30" ITEM PART NO. QTY. DESCRIPTION GA903 L.H. Wing (Shown) GA903 R.H. Wing * GD03 G000 G09 *3 GD05 G0305 G09 Center Seed Hose Bracket Hex Head Cap Screw, ⅜"6 x " Serrated Flange Nut, ⅜"6 Center Bracket Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 * GD006 Manifold Support *5 GD009 G0686 G09 *6 GD09 G000 G09 *7 GD0063 G0305 G09 *8 GD07 G0305 G09 *9 GD0069 G G060 G0670 G055 G078 GD558 G Front Mount Plate Hex Head Cap Screw, ⅜"6 x 8" Serrated Flange Nut, ⅜"6 Hose Tray Support Bracket Hex Head Cap Screw, ⅜"6 x " Serrated Flange Nut, ⅜"6 Front Hose Tray Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 End Hose Tray Carriage Bolt, ⅜"6 x " Serrated Flange Nut, ⅜"6 Pin, ¼" x 7" Hair Pin Clip, No. Cotter Pin, ¼" x " (Toolbox) Hair Pin Clip, No. 3 (Toolbox) Cotter Pin, 6" x ½" (Toolbox) Clevis Pin, 5 6" x " (Toolbox) Lynch Pin, ¼" (Toolbox) Clevis Pin, 3 6" x " (Toolbox) 3 GD5857 Spring (Toolbox) GR00 Offset Link, No. (Toolbox) 5 GR096 Connector Link, No. (Toolbox) 6 GR09 Connector Link, No. 0 (Toolbox) 7 GR09 Offset Link, No. 0 (Toolbox) *Items 9 are for ASD models only. Rev. 9/ P00

180 Wing Frame, 36 Row 0" M0330 (IP8) P0 Rev. 9/

181 M0330 Wing Frame, 36 Row 0" ITEM PART NO. QTY. DESCRIPTION GA903 L.H. Wing (Shown) GA903 R.H. Wing * GD03 Center Seed Hose Bracket G000 Hex Head Cap Screw, ⅜"6 x " G09 Serrated Flange Nut, ⅜"6 *3 GD05 Center Bracket G0305 Carriage Bolt, ⅜"6 x " G09 Serrated Flange Nut, ⅜"6 * GD006 9 Manifold Support *5 GD009 9 Front Mount Plate G Hex Head Cap Screw, ⅜"6 x 8" G09 8 Serrated Flange Nut, ⅜"6 *6 GD09 8 Hose Tray Support Bracket G000 6 Hex Head Cap Screw, ⅜"6 x " G09 6 Serrated Flange Nut, ⅜"6 *7 GD0063 Front Hose Tray G0305 Carriage Bolt, ⅜"6 x " G09 Serrated Flange Nut, ⅜"6 *8 GD07 End Hose Tray G Carriage Bolt, ⅜"6 x " G09 8 Serrated Flange Nut, ⅜"6 *9 GD Pin, ¼" x 7" G Hair Pin Clip, No. 0 GD073 Middle Hose Tray G0305 Carriage Bolt, ⅜"6 x " G09 Serrated Flange Nut, ⅜"6 G060 Cotter Pin, ¼" x " (Toolbox) G Hair Pin Clip, No. 3 (Toolbox) G055 3 Cotter Pin, 6" x ½" (Toolbox) G078 Clevis Pin, 5 6" x " (Toolbox) 3 GD558 Lynch Pin, ¼" (Toolbox) G08 3 Clevis Pin, 3 6" x " (Toolbox) GD5857 Spring (Toolbox) 5 GR00 Offset Link, No. (Toolbox) 6 GR096 Connector Link, No. (Toolbox) 7 GR09 Connector Link, No. 0 (Toolbox) 8 GR09 Offset Link, No. 0 (Toolbox) *Items 9 are for ASD models only. Rev. 9/ P0

182 Hose TakeUp M0330 (IP55) P03 Rev. 9/

183 M0330 Hose TakeUp ITEM PART NO. QTY. DESCRIPTION GA06 Front Hose TakeUp GA07 Rear Hose TakeUp 3 G0756 G09 GD89 G0038 G0 5 GD895 G0038 G0 6 GB08 G39 G0689 G See Junction Block on Hose TakeUp on page P9 Hex Head Cap Screw, ⅜"6 x 6" Serrated Flange Nut, ⅜"6 Spacer, " x 5½" Hex Head Cap Screw, ½"3 x 3" Lock Nut, ½"3 Spacer, " x 8¼" Hex Head Cap Screw, ½"3 x 3" Lock Nut, ½"3 Bushing, 3" I.D. x ⅞" O.D. x 9 3" Long Flat Washer, ⅝" SAE Carriage Bolt, ⅝" x " Lock Nut, ⅝" Rev. 9/ P0

184 Axle and Transport Lockup M0330 (IP60) ITEM PART NO. QTY. DESCRIPTION GA90 GA905 G060 Axle W/Grease Fittings, 86¾", Row 30" (NonStock Item) Axle W/Grease Fittings, 96 ¾", 36 Row 0" (NonStock Item) Grease Fitting, ¼"8 GD783 Transport Rod, ½" x ¾" 3 GD380 Sleeve, ⅝" I.D. x ⅞" O.D. x ⅜" Long G39 Flat Washer, ⅝" SAE 5 GA068 Spring W/Plug 6 GA675 Mechanical Trip Actuator 7 GA086 Transport Lockup 8 G0055 Hex Head Cap Screw, ⅝" x ¼" 9 G00 Hex Nut, ½"3 0 G038 Hex Head Cap Screw, ½"3 x 5" GD95660 Pin, ⅛" x 3⅜" G06 Cotter Pin, ⅜" x 3" 3 G03 Machine Bushing, ⅛", 0 Gauge GD75 Steel Bushing, " Wide P05 Rev. 9/

185 M0330 Transport Wheel and Hub Assembly (FFd/A73) ITEM PART NO. QTY. DESCRIPTION (Per Assy.) G0376 Hex Head Cap Screw, 5 6"8 x ¾" GD59 Dust Cap 3 GD536 Seal G060 Cotter Pin, ¼" x " 5 G0070 Slotted Hex Nut, ¼" 6 G396 Flat Washer, ¼" 7 GA0705 Outer Bearing 8 GA5965 GR03 GD853 G0373 GR057 Hub W/Cups, Grease Fitting And Stud Bolts (0 Bolt) Outer Cup Inner Cup Grease Fitting, 5, ⅛"7 Stud Bolt, ¾"6 x ½" 9 GA5987 Inner Bearing 0 GA5988 Seal GD335 Tire, 36" x 6" x 7.5", Ply, Tubeless (Specify Brand*) GD Outer Budd Nut 3 GA6738 Rim, 8½" Deep GD9508 GD567 0 Inner Budd Nut, ¼" Long Inner Budd Nut, ⅝" Long 5 GA73 Valve Stem * Specific brand requests will be supplied only as available from current Kinze Repair Parts stock. If a specific brand requested is not in stock, the brand available will be supplied. Rev. 9/ P06

186 Wheel Module Assembly M0330 PFA056(FF83d/FF3) R.H. Side Shown Long Wheel Arm Short Wheel Arm P07 Rev. 9/

187 M0330 Wheel Module Assembly ITEM PART NO. QTY. DESCRIPTION (Per Machine) G Swivel Elbow, 5, ¾"6 Male JIC To Female G68008 GR037 8 Elbow W/ORing, 90, ¾"6 Male JIC To ORing ORing 3 See Master Cylinder on page P35 G0397 G389 G0 Hex Head Cap Screw, ½"3 x ¾" Flat Washer, ½" SAE Lock Nut, ½"3 5 See Contact Wheel Assembly on page P 6 G0036 G098 G00 G007 8 Hex Head Cap Screw, ⅝" x " Machine Bushing, ⅝", Gauge (If Applicable) Hex Nut, ⅝" Lock Nut, ⅝" 7 GA75 8 Sprocket W/Bearing, 8 Tooth 8 GB058 Stepped Spacer, ⅞" 9 GD5857 Spring 0 G0860 Retaining Ring, ⅜" G066 Clevis Pin, ⅜" x ½" A733 Wheel Tower (NonStock Item) See Point Row Clutch on page P3 See TwoSpeed Point Row Clutch on page P5 3 GD Stepped Spacer, ½" G0053 G035 G08 G Hex Head Cap Screw, ½"3 x ½" Machine Bushing, ⅞", Gauge Lock Washer, ½" Hex Nut, ½"3 5 GD98 Plate 6 G0003 Bearing, ⅞" Hex Bore, Spherical 7 G3000 Flangette 8 GA53 GA507 Sprocket, 8 Tooth Sprocket, 9 Tooth 9 GD05 Lock Clamp 0 G030 G093 Square Head Machine Bolt, 5 6"8 x ¾" Flange Nut, 5 6"8, No Serration GD09 GD0963 Hex Shaft, ⅞" x " (No Holes) Hex Shaft, ⅞" x 63" (No Holes) See Seed Rate Transmission and Driveline on page P7 3 G033 Machine Bushing, ", 0 Gauge (As Required) G3308 GR09 Chain, No. 0, 8 Pitch Including Connector Link Connector Link, No. 0 5 See Ratchet/Sprocket Assembly on page P9 6 GA955 Idler W/Sprocket And Hardware, R.H. GA75 Sprocket W/Bearing, 8 Tooth G007 Hex Head Cap Screw, ½"3 x ½" G08 Machine Bushing, ½", Gauge G050 Hex Jam Nut, ½"3, Grade 7 G0595 G0875 G387 G008 Hex Head Cap Screw, ⅜"6 x 0" Hex Head Cap Screw, ⅜"6 x " Flat Washer, ⅜" SAE Lock Nut, ⅜"6 Rev. 9/ P08

188 Wheel Module Assembly M0330 ITEM PART NO. QTY. (Per Machine) 8 G0338 G0303 G03 G DESCRIPTION Carriage Bolt, 5 6"8 x ¼" Carriage Bolt, 5 6"8 x " Lock Washer, 5 6" Hex Nut, 5 6"8 9 G Spring Pin, ¼" x " 30 GD95 6 Cylinder Pivot Mount 3 GD955 6 Cylinder Anchor Pin, " x 6" 3 GA59 Sprocket, 50 Tooth 33 See Ground Drive Tire Assembly on page P0 3 GA875 G GA87 G G0006 G39 G030 G00 37 GA73 G GD695 G GD0686 G05 0 G0035 G GD036 Plate, Special Row Spacing Only G007 G08 Long Wheel Arm W/Grease Fitting (Inner) Grease Fitting, ¼"8 Short Wheel Arm W/Grease Fitting (Outer) (Lift Assist For 36 Row 0" Only) Grease Fitting, ¼"8 Hex Head Cap Screw, ⅝" x ¼" Flat Washer, ⅝" SAE Lock Washer, ⅝" Hex Nut, ⅝" Bracket W/Grease Fittings Grease Fitting, ¼"8 Pin, ¼" x 3¼" Spring Pin, ⅜" x " Special Lock Collar, Less Set Screws Square Head Set Screw, 5 6"8 x ½" Hex Head Cap Screw, ½"3 x " Lock Washer, ½" Hex Head Cap Screw, ½"3 x ½" Lock Washer, ½" 3 GD037 Shaft, Special Row Spacing Only GD585 G Pin, ¼" x ½" Cotter Pin, ¼" x " 5 A070 Wheel Tower (Center Wheel Module On 36 Row 0" Only) (NonStock Item) 6 G0599 G06 Carriage Bolt, ⅜"6 x ¼" Serrated Flange Nut, ⅜"6 7 GD703 Plate 8 GD5 Catch 9 G078 Hose Clamp, No GD3650 Pipe, " x 50" A GK69 Lock Clamp Kit (Items 9 And 0) P09 Rev. 9/

189 M0330 Ground Drive Tire Assembly PFA056/PTD057(FF3e/A73) ITEM PART NO. QTY. DESCRIPTION (Per Assy.) GD309 Tire, 5570R.5" W/O Center Rib, Tubeless (Specify Brand*) GA969 Rim, 5.5" x.5" 3 GA376 GD90 GD58 GA8 GR03 Spindle W/Round External Retaining Ring, 0" Round External Retaining Ring Spindle (Sub GA376) Hub W/Cups, 6 Bolt Cup 5 GA0895 Bearing 6 G08 Hex Jam Nut, ½", Grade 7 See Wheel Module Assembly on page P07 8 G006 G03 9 GR070 6 Lug Bolt, 9 6"8 0 GA73 Valve Stem Hex Head Cap Screw, ¾"0 x " Lock Washer, ¾" A GA960 Tire And Rim Assembly W/O Center Rib (Items, And 0) (Specify Brand*) B GA377 Hub And Spindle Assembly (Items 36) *Specific brand requests will be supplied only as available from current Kinze Repair Parts stock. If a specific brand requested is not in stock, the brand available will be supplied. Rev. 9/ P0

190 Contact Wheel Assembly M0330 (FF3e) P Rev. 9/

191 M0330 Contact Wheel Assembly ITEM PART NO. QTY. (Per Assy.) GA9 GA53 GA9 GA505 G0303 G DESCRIPTION Sprocket, Tooth Sprocket, 8 Tooth Sprocket, Tooth Sprocket, 5 Tooth Carriage Bolt, 5 6"8 x " Serrated Flange Nut, 5 6"8 3 G033 Machine Bushing, ", 0 Gauge (As Required) GA3553 GD GD700 GD70 Rim, 3.75" x 8" Sleeve Tire,.80" x 8", Ply, Rib Implement (Specify Brand*) Valve Stem 6 GD558 Lynch Pin, ¼" 7 GA986 Flanged Bearing, ⅞" Hex Bore 8 G060 Spring Pin, ¼" x ½" 9 G3308 G33050 G33058 G330 GR09 Chain, No. 0, 8 Pitch Including Connector Link (Used With Tooth Sprocket) Chain, No. 0, 50 Pitch Including Connector Link (Used With 8 Tooth Sprocket) Chain, No. 0, 58 Pitch Including Connector Link (Used With Tooth Sprocket) Chain, No. 0, Pitch Including Connector Link (Used With 5 Tooth Sprocket) Connector Link, No. 0 0 G0890 Hex Head Adjusting Bolt, ½"3 x ", Grade G050 Hex Jam Nut, ½"3, Grade G0008 G035 G39 G007 Hex Head Cap Screw, ⅝" x " Machine Bushing, ⅞", Gauge Flat Washer, ⅝" SAE Lock Nut, ⅝" 3 GA068 Spring W/Plug GB08 Bushing, 3" I.D. x ⅞" O.D. x 9 3" Long 5 GA737 Wheel Arm 6 GD6775 Hex Shaft, ⅞" x ¾" ( Holes) A GA355 Tire And Rim Assembly (Items And 5) (Specify Brand*) * Specific brand requests will be supplied only as available from current Kinze Repair Parts stock. If a specific brand requested is not in stock, the brand available will be supplied. Different brand tires may have different diameters. Change in tire brand may affect rates. Field checks are recommended after any change in contact tires. Rev. 9/ P

192 Point Row Clutch M0330 PRC08/ECP03(TWL70g/TWL7d/TWL8/A005) Output Shaft Input Shaft Harness Between Clutch Solenoid And Valve Block On R.H. Wing On Point Row Clutch P3 Rev. 9/

193 M0330 Point Row Clutch ITEM PART NO. QTY. DESCRIPTION (Per Assy.) G060 Cotter Pin, ¼" x " G037 G07 3 GD5 VRing Seal GD53 Felt Washer 5 G009 G00 G387 G09 G097 6 G003 G07 G003 7 GA8393 GR306 GR303 GR30 GR305 8 G0900 G07 G Hex Socket Head Cap Screw, ¼"0 x " Lock Washer, ¼" Hex Head Cap Screw, ⅜"6 x ½" Hex Nut, ⅜"6 Flat Washer, ⅜" SAE Lock Washer, ⅜" Hex Jam Nut, ⅜"6, Grade Hex Head Cap Screw, ¼"0 x ¾" Lock Washer, ¼" Hex Nut, ¼"0 Solenoid Complete Snap Ring Spring Boot Plunger Hex Socket Head Cap Screw, ¼"0 x ¾", Grade 8 Lock Washer, ¼" Hex Nut, ¼"0 9 GD03 Spring 0 GD003 Mounting Plate GD9667 Bushing GD090 Hex Shaft, ⅞" x 0" (No Holes) 3 GD093 Hex Shaft, ⅞" x 3" (No Holes) GD7867 Coupler, 3" 5 GD0068 Input Shaft, R.H. Threads 6 GD0070 Coupler W/R.H. Threads 7 G096 External Inverted Snap Ring, ½" 8 GD00 Input Hub 9 GA737 G0765 G080 Hub/Sleeve Assembly W/Spring Pins Spring Pin, ¼" x " Spring Pin, 5 3" x ⅞" 0 GD967 Spring, L.H. GD00 Stop Collar GD0 Rue Ring Cotter, 5 6" 3 GD050 Actuator Arm G0859 Spring Pin, 3 6" x ¼" 5 G053 G Hex Socket Head Screw, No. 03 x ½" Lock Washer, No. 0 6 G056 Spring Pin, 3 6" x ¼" 7 GD350 Lock Wire, 0", Stainless Steel 8 GA979 GA95 Wiring Harness, 8", R.H. Side Of Machine Wiring Harness, 56", L.H. Side Of Machine 9 G0996 Fork Terminal 30 GA005 Ground Cable, Green A GA7 Point Row Clutch Assembly, L.H. (Items, 57, and 30) Rev. 9/ P

194 TwoSpeed Point Row Clutch M0330 PRC03(FF7c/A77/A005) Output Shaft Input Shaft Jumper Wire Between Point Row Clutch Solenoids Harness Between Clutch Solenoid And Valve Block On R.H. Wing P5 Rev. 9/

195 M0330 TwoSpeed Point Row Clutch ITEM PART NO. QTY. (Per Assy.) GD0635 G003 G07 GD08 G003 G07 G003 DESCRIPTION Threaded Rod, ¼"0 x 3½" Hex Nut, ¼"0 Lock Washer, ¼" Allen Nut, ¼"0 Hex Head Cap Screw, ¼"0 x ¾" Lock Washer, ¼" Hex Nut, ¼"0 3 GD03 Spring GD0636 G008 G09 G00 Threaded Rod, ⅜"6 x ¼" Lock Nut, ⅜"6 Lock Washer, ⅜" Hex Nut, ⅜"6 5 GA763 GD00 GD058 G0873 G087 G080 G GA8393 GR306 GR303 GR30 GR305 Hub/Sleeve Assembly W/Seals, Sleeve, Pins And Screws Seal Sleeve Hex Socket Set Screw, 5 6"8 x ¾" Hex Socket Set Screw, 5 6"8 x ¼" Spring Pin, 5 3" x ⅞" Spring Pin, ¼" x " Solenoid Complete Snap Ring Spring Boot Plunger 7 GD050 Actuator Arm 8 GD0586 Bushing 9 GD003 Mounting Plate 0 G0859 Spring Pin, 3 6" x ¼" G Hex Socket Head Screw, No. 03 x ¼" GD967 Spring, L.H. 3 GD0585 Stop Collar GA957 GD00 Hub W/Seal Seal 5 G096 External Inverted Snap Ring, ½" 6 GD0579 Output Sprocket, 8 Tooth 7 GD090 Hex Shaft, ⅞" x 0" (No Holes) 8 GD0 Rue Ring Cotter, 5 6" 9 GA957 GD00 Hub W/Seal Seal 0 G060 Cotter Pin, ¼" x " G037 GD Hex Socket Head Cap Screw, ¼"0 x " Key GD093 Hex Shaft, ⅞" x 3" (No Holes) 3 GD7867 Coupler, 3" GD0068 Input Shaft, R.H. Threads 5 GD0578 Input Sprocket, 8 Tooth 6 GD0638 Coupler W/R.H. Threads 7 G0996 Fork Terminal 8 GA77 Jumper Wire W/Ring Terminals, 3 6" 9 GD53 Felt Washer 30 GA979 GA95 Wiring Harness, 8", R.H. Side Of Machine Wiring Harness, 56", L.H. Side Of Machine 3 GD967 Spring, R.H. Rev. 9/ P6

196 TwoSpeed Point Row Clutch Wheel Module Extensions M0330 (FF8c) To Transmission ITEM PART NO. QTY. DESCRIPTION (Per Assy.) See Wheel Module Assembly on page P07 GD037 Extension Plate 3 GA53 Sprocket, 8 Tooth G033 Machine Bushing, ", 0 Gauge 5 G030 G093 Square Head Machine Bolt, 5 6"8 x ¾" Flange Nut, 5 6"8, No Serration 6 GA75 Sprocket W/Bearing, 8 Tooth 7 G0053 G068 G389 G08 G00 3 Hex Head Cap Screw, ½"3 x ½" Machine Bushing, ½", 7 Gauge Flat Washer, ½" SAE Lock Washer, ½" Hex Nut, ½"3 8 G033 Machine Bushing, ", 0 Gauge (As Required) 9 GD057 Jack Shaft, ⅞" x 3" 0 GA733 Sprocket Storage Rod GD558 Lynch Pin, ¼" G0037 G389 G08 G00 Hex Head Cap Screw, ½"3 x ¼" Flat Washer, ½" SAE Lock Washer, ½" Hex Nut, ½"3 P7 Rev. 9/

197 M0330 TwoSpeed Point Row Clutch Wheel Module Extensions ITEM PART NO. QTY. (Per Assy.) 3 G33068 GR09 GR09 GA505 GA506 GA509 GA5 GA508 GA50 GA5 DESCRIPTION Chain, No. 0, 68 Pitch Including Connector Link Connector Link, No. 0 Offset Link, No. 0 Sprocket, 5 Tooth Sprocket, 7 Tooth Sprocket, Tooth Sprocket, 7 Tooth Sprocket, 3 Tooth (From Transmission) Sprocket, 5 Tooth (From Transmission) Sprocket, 6 Tooth (From Transmission) 5 G3000 Flangette 6 G0003 Bearing, ⅞" Hex Bore, Spherical 7 G0338 G03 G Carriage Bolt, 5 6"8 x ¼" Lock Washer, 5 6" Hex Nut, 5 6"8 8 GD05 Lock Clamp 9 GD0637 Stepped Spacer, ½" 0 G060 Spring Pin, ¼" x ½" GA59 Sprocket, 50 Tooth G008 G009 3 G030 G03 G386 G006 G0595 G008 5 GA73 G030 GD55 G056 G070 GD0366 GA737 GA Clevis Pin, 5 6" x ¾" Retaining Ring, 5 6" Carriage Bolt, 5 6"8 x ⅞" Lock Washer, 5 6" Flat Washer, 5 6" SAE Hex Nut, 5 6"8 Hex Head Cap Screw, ⅜"6 x 0" Lock Nut, ⅜"6 Overrunning Sprocket Assembly, L.H. External Retaining Ring, ¼" LPin Spring Pin, 3 6" x ¼" Cotter Pin, 5 3" x " Spring Block Sprocket W/Bushing, 30 Tooth 6 See TwoSpeed Point Row Clutch on page P5 7 G3308 GR09 GR09 8 GD058 Output Shaft, ⅞" x " 9 GA999 GA75 G007 G08 G GD5857 Spring 3 G0036 G39 G007 G00 Chain, No. 0, 8 Pitch Including Connector Link Connector Link, No. 0 Offset Link, No. 0 Idler W/Sprocket And Hardware, R.H. Sprocket W/Bearing, 8 Tooth Hex Head Cap Screw, ½"3 x ½" Machine Bushing, ½", Gauge Hex Jam Nut, ½"3, Grade Hex Head Cap Screw, ⅝" x " Flat Washer, ⅝" SAE Lock Nut, ⅝" Hex Nut, ⅝" A GK69 Lock Clamp Kit (Items 5 And 8) Rev. 9/ P8

198 C B A A B C A B C Airline Fittings and Hoses, Row 30" M0330 IP75 7 Row One High Pressure Sensor (00 p.s.i.) P/N: A86 9 To Main Planter Harness 3 ITEM PART NO. QTY. DESCRIPTION See Air Compressor and Dual Solenoid Assembly on page P3 See Accumulator Assembly on page P5 3 See Clutch Valve Assembly on page P5 GD750 3 Nylon Tubing, ¼" O.D. x 5', Row 5 GD750 3 Nylon Tubing, ¼" O.D. x 5', Row 6 GD805 Tee, ¼" Press On 7 See Air Clutch, Pull Row Unit on page P5 8 GD800 Tee, ⅜" Tube Union 9 GD7506 Nylon Tubing, ¼" O.D. x ½' 0 GD8796 Reducer, ⅜" To ¼" GA86 High Pressure Sensor (00 PSI) GA8 Hall Effect Adapter 3 GA369 GR83 Tube Cutter W/Blade Blade P9 Rev. 9/

199 C B A A B C A B C M0330 Airline Fittings and Hoses, 36 Row 0" (IP76) 7 Row One High Pressure Sensor (00 p.s.i.) P/N: A86 0 To Main Planter Harness 3 ITEM PART NO. QTY. DESCRIPTION See Air Compressor and Dual Solenoid Assembly on page P3 See Accumulator Assembly on page P5 3 See Clutch Valve Assembly on page P5 GD750 Nylon Tubing, ¼" O.D. x 5' 5 GD750 Nylon Tubing, ¼" O.D. x 5' 6 GD805 9 Tee, ¼" Press On (Air Clutch) 7 See Air Clutch, Pull Row Unit on page P5 8 GD800 Tee, ⅜" Tube Union 9 GD7506 Nylon Tubing, ¼" O.D. x ½' 0 GD8796 Reducer, ⅜" To ¼" GA86 High Pressure Sensor (00 PSI) GA8 Hall Effect Adapter 3 GA369 GR83 Tube Cutter W/Blade Blade Rev. 9/ P0

200 Pneumatic Down Pressure Control Console, Sending Unit, and Harnesses M0330 (PNE0i/MTR7a/ELC7b/MTR5/MTR7t) P Rev. 9/

201 M0330 Pneumatic Down Pressure Control Console, Sending Unit, and Harnesses ITEM PART NO. QTY. DESCRIPTION GA7856 Power Lead Adapter GA6 Control Console Assembly 3 GA86 High Pressure Sensor (00 PSI) GA65 GD58 GD660 Wiring Harness W/Fuse Holder And Fuse, 06" Fuse Holder Fuse, Amp Delay Action 5 GK68 Console Cable Connector Kit, Includes: () 3Pin Connector, () Cable Clamp, () Lock Ring, (3) Female Terminal Pins 6 GK67 Console Cable Connector Kit, Includes: () 3Pin Connector, () Cable Clamp, (3) Male Terminal Pins 7 GA9963 Strain Relief 8 GR9 Pan Head Screw, No. 83 x ½" 9 GR363 Hex Face Nut, 5 3"3 0 GA6978 Switch, 3 Position Toggle, ONOFFON GK8 3Pin Female Connector Kit (Black), Includes: (3) 3Pin Female Housings, (9) Pin Contacts, (9) Seals GK5 3Pin Male Connector Kit (Black), Includes: (3) 3Pin Male Housings, (9) Socket Contacts, (9) Seals 3 GA838 Pin Female Connector Kit, Includes: () Pin Female Housing, () Pin Contacts, () Seals GA839 Pin Male Connector Kit, Includes: () Pin Male Housing, () Socket Contacts, () Seals 5 GK396 6Pin Female Connector Kit (Black), Includes: (3) 6Pin Female Housings,(8) Pin Contacts, (8) Seals 6 GK395 6Pin Male Connector Kit (Black), Includes: (3) 6Pin Male Housings, (8) Socket Contacts, (8) Seals 7 GK3 Pin Female Connector Kit (Black), Includes: (3) Pin Female Housings, (6) Pin Contacts, (6) Seals 8 GK30 Pin Male Connector Kit (Black), Includes: (3) Pin Male Housings, (6) Socket Contacts, (6) Seals 9 GA996 Strain Relief 0 GA68 GD58 GD875 Wiring Harness W/Fuse Holder And Fuse, 0' Fuse Holder Fuse, 0 Amp GA669 Wiring Harness, 0' See Air Compressor and Dual Solenoid Assembly on page P3 3 GD7506 Nylon Tubing, ¼" O. D. x ½' GD8796 Reducer, ⅜" To ¼" 5 GD800 Tee, ⅜" Tube Union Rev. 9/ P

202 Air Compressor and Dual Solenoid Assembly M0330 (IP8) ITEM PART NO. QTY. DESCRIPTION GD8 G066 G099 Cover Phillips Pan Head Machine Screw, No. 0 x ¾", Stainless Steel Serrated Flange Nut, No. 0 GA7 GR93 3 GA0 G066 G099 GA358 G009 G03 G09 G006 5 GD38033 Sleeve, 7" 6 GD890 Tap Block, Long Filter Assembly Filter Air Compressor Phillips Pan Head Machine Screw, No. 0 x ¾", Stainless Steel Serrated Flange Nut, No. 0 Mount Hex Head Cap Screw, 5 6"8 x " Lock Washer, 5 6" Washer, 5 6" USS Hex Nut, 5 6"8 P3 Rev. 9/

203 M0330 Air Compressor and Dual Solenoid Assembly ITEM PART NO. QTY. DESCRIPTION 7 GD00 Bracket G03 3 Hex Head Cap Screw, ⅝" x 8" 8 G006 G03 G386 G07 Hex Nut, 5 6"8 Lock Washer, 5 6" Flat Washer, 5 6" SAE Hex Head Cap Screw, 5 6"8 x ¼" 9 GA988 Tank, 3 Gallon 0 GA35 Valve Stem, ¼" NPT GD937 Tee, ¼" NPT GD756 3 Plug, ¼" NPT 3 GD938 Close Nipple, ¼" NPT GR778 Pressure Switch 5 GA99 Drain, ¼" NPT 6 GR95 Leader Hose without Check Valve 7 GR9 Check Valve 8 GD808 G003 G07 G003 9 GA69 GD9080 Regulator Bracket Hex Head Cap Screw, ¼"0 x ¾" Lock Washer, ¼" Hex Nut, ¼"0 Mini Regulator W/Gauge Elbow, ¼" x ⅛" NPT Swivel 0 GA0 Pressure Gauge, ¼" NPT GD8078 Female Cross, ¼" NPT GD75 Connector, ¼" Male NPT 3 GD756 Plug, ¼" NPT G000 G07 Hex Head Cap Screw, ¼"0 x ¾" Lock Washer, ¼" 5 GA993 Block 6 GD73 Swivel Elbow, ¼" NPT x ⅜" 7 GA997 Breather, ¼" NPT 8 GR95 GR953 G056 9 GA99 G3 Socket Head Cap Screw, #83 x " ORing Lock Washer, No. 8 Solenoid Phillips Pan Head Machine Screw 30 GD7 Connector, ¼" Male NPT 3 GA99 Shutoff Valve, ¼" NPT A GA66 Air Compresor Assembly (Items, and 95) B GA995 Dual Solenoid Assembly (Items 03) (only applicable with pneumatic down pressure option) C GR783 Valve Seal Repair Kit Rev. 9/ P

204 Accumulator Assembly M0330 (IP00a) ITEM PART NO. QTY. DESCRIPTION GA358 Compressor Mount GA988 Tank, 3 Gallon 3 GD78 Male Connector, ¼" GD756 Plug, ¼" NPT 5 GD9079 Plug, ⅛" NPT 6 G060 G003 Serrated Flange Nut, 5 6"8 Hex Head Cap Screw, 5 6"8 x ¾" 7 GA99 Drain, ¼" NPT 8 G03 3 Hex Head Cap Screw, ⅝" x 8" 9 GD00 Bracket 0 GD38033 Sleeve, 7" GD890 Tap Block, Long G07 G03 G09 G006 Hex Head Cap Screw, 5 6"8 x ¼" Lock Washer, 5 6" Washer, 5 6" USS Hex Nut, 5 6"8 P5 Rev. 9/

205 This page left blank intentionally.

206 Seed Rate Transmission and Driveline M0330 (FFg) R.H. Side Shown ITEM PART NO. QTY. DESCRIPTION (Per Assy.) G0008 G030 G00 Hex Head Cap Screw, ⅝" x " Lock Washer, ⅝" Hex Nut, ⅝" G008 G03 G39 G005 Hex Head Cap Screw, ¾"0 x 3" Lock Washer, ¾" Flat Washer, ¾" SAE Hex Nut, ¾"0 3 G033 Machine Bushing, ", 0 Gauge See Wheel Module Assembly on page P07 5 G060 Cotter Pin, ¼" x " 6 GD UBolt, 7" x 7" x ⅝" G007 Lock Nut, ⅝" 7 G030 G093 8 GD7867 Coupler, 3" 9 GA569 GA56 3 GA56 GD655 G060 0 GD77 Shear Coupler Square Head Machine Bolt, 5 6"8 x ¾" Flange Nut, 5 6"8, No Serration Transmission Plate W/Bearings, Grease Fittings And Retaining Rings Bearing, ⅞" Hex Bore, Cylindrical Special Bearing, ⅞" Hex Bore x.6" Ring Grease Fitting, ¼"8 P7 Rev. 9/

207 M0330 Seed Rate Transmission and Driveline ITEM PART NO. QTY. DESCRIPTION (Per Assy.) GD5857 Spring G078 Clevis Pin, 5 6" x " G009 3 GA7336 GD76 GD06 G387 G09 G007 Retaining Ring, 5 6" Idler W/BoltOn Sprockets Sprocket, Tooth Sleeve, 3 6" Long Flat Washer, ⅜" SAE Lock Washer, ⅜" Hex Head Cap Screw, ⅜"6 x ¾" GD5835 Shaft, ⅞" x 7" 5 G060 3 Spring Pin, ¼" x ½" 6 GD558 3 Lynch Pin, ¼" 7 GA56 Sprocket Storage Rod 8 G007 G08 G00 9 GA506 GA507 GA508 GA509 GA50 GA5 GA5 GA53 Hex Head Cap Screw, ½"3 x ½" Lock Washer, ½" Hex Nut, ½"3 Sprocket, 7 Tooth Sprocket, 9 Tooth Sprocket, 3 Tooth Sprocket, Tooth Sprocket, 5 Tooth Sprocket, 6 Tooth Sprocket, 7 Tooth Sprocket, 8 Tooth 0 G33080 GR09 GD78 Shaft, ⅞" x 7" G08 Clevis Pin, 3 6" x " G055 Cotter Pin, 6" x ½" 3 GB087 Coupler G03 Square Head Set Screw, 5 6"8 x ¾" 5 G000 Hex Head Cap Screw, ⅜"6 x ¼" G09 Lock Washer, ⅜" G00 Hex Nut, ⅜"6 Chain, No. 0, 80 Pitch Including Connector Link Connector Link, No. 0 6 GA80 Hanger Bearing, ⅞" Hex Bore, 36 Row 0" Only 7 GD095 Hex Shaft, ⅞" x 5" (No Holes) 8 GD05 Lock Clamp 9 GD79 Coupler, ", Row 30" 30 G033 Machine Bushing, ", 0 Gauge 3 GD0998 GD0908 GD G00 G07 G385 Hex Shaft, ⅞" x 98" (No Holes), R.H. And L.H. Sides, Row 30" Hex Shaft, ⅞" x 08" (No Holes), R.H. Side, 36 Row 0" Hex Shaft, ⅞" x 98" (No Holes), L.H. Side, 36 Row 0" Hex Socket Button Head Cap Screw, ¼"0 x ½", Grade 8 Lock Washer, ¼" Flat Washer, ¼" SAE 33 G078 Vinyl Cap 3 G096 External Inverted Snap Ring, ½" 35 G075 3 External Inverted Snap Ring, ⅞" 36 GD3 Sleeve, ¼" 37 GD3 GD Torsion Spring, L.H. (Shown) Torsion Spring, R.H. 38 GD933 GD93 Release Collar, R.H.(Shown) Release Collar, L.H. 39 GD7 Tightener Shaft, ⅞" 0 GD3 Handle GA95 Mount, 36 Row 0" Only (Shown) A GK69 Lock Clamp Kit (Items 7 And 8) B GK378 Wrap Spring Wrench Replacement Kit, Gold Collar, R.H. (Items 30) GK379 Wrap Spring Wrench Replacement Kit, Silver Collar, L.H. (Items 30) Rev. 9/ P8

208 Ratchet/Sprocket Assembly M0330 PTD06(TWL) ITEM PART NO. QTY. DESCRIPTION (Per Assy.) GD56 Spring G053 Cotter Pin, 3 6" x " 3 GA0378 Block And Hub Assembly GD55 LPin 5 GA565 Sprocket, 30 Tooth 6 G030 External Retaining Ring, ¼" A GA56 Ratchet/Sprocket Assembly (Items 6) P9 Rev. 9/

209 M0330 Row Marker Assembly (IP5/IP77/A05/A058) L.H. Side Shown D597 D D38 7 A A057 5 A05 A03 3 R05 R050 0 B065 A067 ITEM PART NUMBER IP J Rev. 9/ P30

210 Row Marker Assembly M0330 ITEM PART NO. QTY. DESCRIPTION (Per Assy.) See Row Marker Spindle/Hub/Blade on page P33 GD05307 Extension Tube, 5" 3 GA903 GA690 G060 GA6860 GA385 G058 G0 G GD070 G060 6 GA060R GA060L 7 GA90 GA803 8 GD7 G08 G00 9 GA87 G GD996 G059 G060 GD0677 G06 GA90 GA69 G060 3 GD9 G387 G Arm W/Grease Fittings, Third Stage, 7", Row 30" and 36 Row 0" Arm W/Grease Fittings, Third Stage, 57", Row 0" Grease Fitting, ¼"8 Control Arm, Row 30" and 36 Row 0" Control Arm, Row 0" Hex Head Cap Screw, ½"3 x ¼" Lock Nut, ½"3 Hex Head Cap Screw, ½"3 x 3½" Pin, ¼" x " Cotter Pin, ¼" x " Support, R.H. Support, L.H. (Shown) Stop Weld, Row 30" and 36 Row 0" Stop Weld, Row 0" UBolt, " x " x ½"3 Lock Washer, ½" Hex Nut, ½"3 Safety Lockup W/Detent Pins, 0" Detent Pin, ½" x ½" Grip Pin, ¼" x 0½" Washer, ⅞" Cotter Pin, ¼" x " Pin, ⅛" x 5¾" Cotter Pin, ⅜" x 3" Arm W/Grease Fittings, Second Stage, 85", Row 30" and 36 Row 0" Arm W/Grease Fittings, Second Stage, 0", Row 0" Grease Fitting, ¼"8 UBolt, ½" x ⅜"6 Lock Washer, ⅜" Hex Nut, ⅜"6 See Row Marker (Cushion) Cylinder on page P38 5 G68008 G60008 GR037 G30C8 6 GA6870 G G007 G03 G005 8 GA03 G060 GD5875 G008 G007 9 GD086 G060 0 GA3 Marker Tire Support GD96 Plate G05 G00 G Elbow W/ORing, 90, ¾"6 Male JIC To ORing Connecter W/ORing, ¾"6 Male JIC To ORing ORing Cap Nut, ¾"6 Arm, First Stage Hex Head Cap Screw, ½"3 x 3" Hex Head Cap Screw, ¾"0 x ½" Lock Washer, ¾" Hex Nut, ¾"0 Mount W/Grease Fittings Grease Fitting, ¼"8 Hose Clamp, 9 6" x ½" x " Lock Nut, ⅜"6 Hex Head Cap Screw, ⅜"6 x ¾" Pin, ¼" x 9½" Cotter Pin, ¼" x " Hex Head Cap Screw, ⅝" x 9" Hex Nut, ⅝" Lock Washer, ⅝" P3 Rev. 9/

211 M0330 Row Marker Assembly ITEM PART NO. QTY. (Per Assy.) 3 GD08 GD36 GA06 DESCRIPTION GA058 Valve Stem 5 GD080 Dust Cap 6 G05 Cotter Pin, 5 3" x " 7 GD38 Lug Bolt, ½"0 x ¼" 8 GA05 Bearing 9 GD50 Grease Seal 30 G33005 G330 GD0670 GD GA067 GR05 GR050 GB065 Tube Type Tire, 6" x 6.5" x 8" (Specify Brand*) Tube (Not Shown) Rim, T8 x 5.38" x 3 GA057 Bearing 33 G39 Flat Washer, ⅝" SAE 3 G075 Slotted Hex Nut, ⅝"8 35 GD597 Retainer Coil Chain, No. 9/0, 79 Links, Row 30" and 36 Row 0" Coil Chian, No. 9/0, 5 Links, Row 0" Nylon Cover, ", Row 30" and 36 Row 0" Nylon Cover, 00", Row 0" Hub W/Cups, Bolt Outer Cup Inner Cup Hub, Bolt A GA05 Tire And Rim Assembly (Item 3) *Specific brand requests will be supplied only as available from current Kinze Repair Parts stock. If a specific brand requested is not in stock, the brand available will be supplied. Rev. 9/ P3

212 Row Marker Spindle/Hub/Blade M0330 (IP035a) P33 Rev. 9/

213 M0330 Row Marker Spindle/Hub/Blade ITEM PART NO. QTY. DESCRIPTION (Per Assy.) GA5853 Depth Band GD076 GD083 3 G009 G009 Disc Blade, Solid, 6" (Shown) Disc Blade, Notched, 6" (Optional) Hex Head Cap Screw, 5 6"8 x " Lock Nut, 5 6"8, Grade 8 GA067 Hub W/Cups, Bolt (Includes Items 6 and 7) 5 G39 Flat Washer, ⅝" SAE 6 GR05 Outer Cup 7 GD50 Grease Seal 8 G00 Lock Nut, ¼"0, Grade B 9 GA057 Bearing 0 G8 Hex Socket Head Cap Screw, ¼"0 x ½" GB055 Hub Shield GD597 Retainer 3 GD080 Dust Cap G07 G08 Hex Head Cap Screw, ½"0 x " Lock Washer, ½" 5 G05 Cotter Pin, 5 3" x " 6 G075 Slotted Hex Nut, ⅝"8 7 GR050 Inner Cup 8 GA05 Bearing 9 GA55 Spindle 0 G08 G068 G08 G00 G005 G068 G08 G00 Carriage Bolt, ½"3 x 3½" Machine Bushing, ½", 7 Gauge Lock Washer, ½" Hex Nut, ½"3 Hex Head Cap Screw, ½"3 x ½" Machine Bushing, ½", 7 Gauge Lock Washer, ½" Hex Nut, ½"3 A GA379 Hub And Spindle Assembly, (Items 7, 9, and 9) Rev. 9/ P3

214 Master Cylinder M0330 (CYL33d) ITEM PART NO. QTY. DESCRIPTION GA830 GD75 G0939 G00 Clevis W/Bushings, Hex Head Cap Screw And Hex Nut Steel Bushing, " Wide Hex Head Cap Screw, ⅜"6 x ¼" Hex Nut, ⅜"6 GD5 Rod 3 GD5 Gland GD55 Piston 5 G0958 Lock Nut, " 6 A897 Barrel (NonStock Item) A GA898 Cylinder Complete, ½" x 0" (Part Number Stamped On Barrel) B GR530 Seal Kit, Includes: () Wiper, () UCup, () ORings, () BU Ring, () Cast Iron Rings, () Seal, () Energizer Slave Cylinders CYL055(CYL5d) ITEM PART NO. QTY. DESCRIPTION GA830 GD75 G0939 G00 Clevis W/Bushings, Hex Head Cap Screw And Hex Nut Steel Bushing, " Wide Hex Head Cap Screw, ⅜"6 x ¼" Hex Nut, ⅜"6 GD56 Rod 3 GD57 Gland GA896 GR69 5 G0958 Lock Nut, " 6 A8960 Barrel (NonStock Item) Piston W/Rephasing Valve Rephasing Valve Replacement Kit (Set Screw, Guide, Springs And Ball) A GA896 Cylinder Complete, ¾" x 0" (Part Number Stamped On Barrel) B GR56 Seal Kit, Includes: () Wiper, () UCup, () ORings, () BU Ring, () Cast Iron Rings, () Seal, () Energizer P35 Rev. 9/

215 M0330 Hitch Paralled Linkage Cylinder (IP30) ITEM PART NO. QTY. DESCRIPTION A8969 Barrel (NonStock Item) G60808 Plug W/ORing, ¾"6 ORing 3 G0987 Hollow Lock Screw, ¾"6 x ⅜" GD589 Orifice Plate 5 G0087 Hex Jam Nut, ½", Grade 6 *D80 TSeal 7 GD099 Piston 8 *D0990 ORing 9 GD0989 Rod 0 *D3 ORing *D3 Backup Ring *D37 Wear Ring 3 *D6 UCup GD0988 Gland 5 *D63 Wiper 6 *D Ring 7 G0939 Hex Head Cap Screw, ⅜"6 x ¼" 8 G008 Lock Nut, ⅜"6 9 GD95 Clevis A GA697 Cylinder Complete, 3½" x 0" (Part Number Stamped On Barrel) B GR96 Seal Kit, Includes: () Wiper, () UCup, () ORings, () Backup Ring, () TSeal, () Wear Ring, () Ring *Item is part of seal kit, item can not be purchased individually. Rev. 9/ P36

216 Assist Cylinder, 36 Row 0" M0330 (CYL33d) ITEM PART NO. QTY. DESCRIPTION GA830 GD75 G0939 G00 Clevis W/Bushings, Hex Head Cap Screw And Hex Nut Steel Bushing, " Wide Hex Head Cap Screw, ⅜"6 x ¼" Hex Nut, ⅜"6 GD60 Rod 3 GD98 Gland GD600 Piston 5 G0958 Lock Nut, " 6 A07 Barrel (NonStock Item) A GA073 Cylinder Complete, 3" x 0" (Part Number Stamped On Barrel) B GR70 Seal Kit, Includes: () Wiper, () UCup, () ORings, () BU Ring, () Cast Iron Rings, () Seal, () Energizer P37 Rev. 9/

217 M0330 Row Marker (Cushion) Cylinder (IP67) ITEM PART NO. QTY. DESCRIPTION A8950 Barrel (NonStock Item) GD550 Piston, 3½" 3 *D088 Piston Ring GD58 Gland 5 GD3 ORing, No *D5 UCup 7 *D06 Wiper 8 GD03 Ring 9 *D3 Backup Ring 0 GA898 Rod Assembly G0983 Slotted Hex Nut, ⅛" G098 Cotter Pin, 3 6" x ½" 3 G60808 Plug W/ORing, ¾"6 ORing GR037 ORing *D5 ORing, # 5 *D80 TSeal 0 A GA895 Cylinder Complete, 3½" x 0" (Part Number Stamped On Barrel) B GR53 Seal Kit, Includes: () ORings, () UCup, () Wiper, () TSeal, () BU Ring, () Cast Iron Ring *Item is part of seal kit, item can not be purchased individually. Rev. 9/ P38

218 Helper Cylinder, All Sizes M0330 (CYL7a) R.H. Side Only ITEM PART NO. QTY. DESCRIPTION GA890 G060 Rod Assembly W/Grease Fitting Grease Fitting, ¼"8 GD988 Gland 3 GD997 Piston G0958 Lock Nut, " 5 A8300 Barrel (NonStock Item) A GA8906 Cylinder Complete, " x 3⅝" (Part Number Stamped On Barrel) B GR55 Seal Kit, Includes: () ORings, () BU Ring, () UCup, () Wiper, () TSeal Helper Cylinder, All Sizes CYL055(CYL7a) L.H. Side Only ITEM PART NO. QTY. DESCRIPTION GA8907 G060 Rod Assembly W/Grease Fitting Grease Fitting, ¼"8 GD988 Gland 3 GD997 Piston G0958 Lock Nut, " 5 A685 Barrel (NonStock Item) A GA8905 Cylinder Complete, " x 55 3" (Part Number Stamped On Barrel) B GR55 Seal Kit, Includes: () ORings, () BU Ring, () UCup, () Wiper, () TSeal P39 Rev. 9/

219 M0330 Tongue Cylinder, Row 0" (CYL8b) ITEM PART NO. QTY. DESCRIPTION GA9576 Rod Assembly GD38 Gland 3 GD353 Spacer GD39 Piston 5 G097 Lock Nut, ¼" 6 G GR65 Connector W/ORing, ¾"6 Male JIC To 7/6"0 ORing ORing 7 GA05 Steel Hydraulic Line, 55/6" 8 G70008 Bulkhead Tube Union, ¾"6 Male JIC 9 GD363 Bracket 0 G30608 Lock Nut, ¾"6 G038 G09 Hex Head Cap Screw, ⅜"6 x ⅝" Lock Washer, ⅜" G089 Hose Clamp 3 GA9578 Barrel A GA9579 Cylinder Complete, " x 3½" (Part Number Stamped On Barrel) B GR599 Seal Kit, Includes: () ORings, () BU Ring, (3) Wear Rings, () Piston Seal, () UCup, () Wiper, () Expander Rev. 9/ P0

220 Tongue Cylinder, Row 30" and 36 Row 0" M0330 (IP66) P Rev. 9/

221 M0330 Tongue Cylinder, Row 30" and 36 Row 0" ITEM PART NO. QTY. DESCRIPTION A958 Barrel (NonStock Item) GA9580 Rod Assembly 3 G GR65 GA06 G089 5 GD Ring, ½" 6 *D63 Wiper Rod 7 GD38 GD37 Connector W/ORing, ¾"6 Male JIC To 7 6"0 ORing ORing Steel Hydraulic Line, 78¼" Hose Clamp Gland Wear Ring 8 *D6 UCup 9 *D BackUp Ring No. 3 0 *D ORing, No. 3 *D0 ORing, No. 8 GD39 *D65 *D0 *D9 Piston Expander Wear Ring Piston Seal 3 G097 Lock Nut, ¼" GD356 Spacer 5 G70008 G30608 G30C8 6 GD363 G038 G09 7 G60808 GR037 Bulkhead Tube Union, ¾"6 Male JIC Lock Nut, ¾"6 Cap Nut, ¾6 Bracket Hex Head Cap Screw, ⅜"6 x ⅝" Lock Washer, ⅜" Plug W/ORing, ¾"6 ORing ORing A GA9583 Cylinder Complete, " x 6" (Part Number Stamped On Barrel) B GR599 Seal Kit, Includes: () ORings, () BU Ring, (3) Wear Rings, () Piston Seal, () UCup, () Wiper, () Expander *Item is part of seal kit, item can not be purchased individually. Rev. 9/ P

222 Valve Block on Front Hitch M0330 (FF9c) A B C D B3 A3 V9 V0 A C B D B3 ITEM PART NO. QTY. DESCRIPTION GD953 Block G68008 GR037 3 G GR037 6 Elbow W/ORing, 90, ¾"6 Male JIC To ORing ORing Connector W/ORing, ⅞" Male JIC To ¾"6 ORing ORing See Solenoid Valve (GK76) on page P5 5 G033 G03 6 GD3365 Cover 7 G005 G03 G006 Hex Head Cap Screw, 5 6"8 x ½" Lock Washer, 5 6" Hex Head Cap Screw, 5 6"8 x ½" Lock Washer, 5 6" Hex Nut, 5 6"8 8 GD80660 Sleeve, " Long 9 G0977 Phillips Pan Head Machine Screw, No. 0 x ½", Stainless Steel 0 GD338 Insulated Clamp, 6" G067 Phillips Pan Head Machine Screw, No. 83 x ¾", Stainless Steel GA950 GR635 Terminal Strip W/Screws, No. 6, Terminal Screw, No. 63 x ¼" 3 GA958 Terminal Strip Mount G066 Phillips Pan Head Machine Screw, No. 0 x ¾", Stainless Steel 5 G GR037 Elbow W/ORing, 90, ⅞" Male JIC To ¾"6 ORing ORing 6 G65000 Swivel Elbow, 90, ⅞" Male JIC To Female P3 Rev. 9/

223 M0330 Valve Block on Tower Assembly (FF0a) D5 D7 V D6 D3 D ITEM PART NO. QTY. DESCRIPTION GD9536 Block G GR037 3 G68008 GR037 GD338 Insulated Clamp, 6" 5 GD3366 Cover 6 G005 G03 G006 7 G0583 G03 3 Elbow W/ORing, 90, ⅞" Male JIC To ¾"6 ORing ORing Elbow W/ORing, 90, ¾"6 Male JIC To ORing ORing Hex Head Cap Screw, 5 6"8 x ½" Lock Washer, 5 6" Hex Nut, 5 6"8 Hex Head Cap Screw, 5 6"8 x ¾" Lock Washer, 5 6" 8 GD Sleeve, 5 6" Long 9 G067 Phillips Pan Head Machine Screw, No. 83 x ¾", Stainless Steel 0 GA95 GR635 Terminal Strip W/Screws, No. 6, Terminal Screw, No. 63 x ¼" G066 Phillips Pan Head Machine Screw, No. 0 x ¾", Stainless Steel GA959 Terminal Strip Mount 3 See Solenoid Valve (GK75) on page P5 G0977 Phillips Pan Head Machine Screw, No. 0 x ½", Stainless Steel Rev. 9/ P

224 Valve Block on R.H. Wing M0330 (FFa) V V V8 V7 V3 B V P V6 A B5 A7 B7 A5 B9 P3 A9 B V5 A P5 Rev. 9/

225 M0330 Valve Block on R.H. Wing ITEM PART NO. QTY. DESCRIPTION G60008 GR037 6 Connector W/ORing, ¾"6 Male JIC To ORing ORing See Flow Control Valve on page P53 3 See Solenoid Valve (GK75) on page P5 See Solenoid Valve (GK76) on page P5 5 G608H06O GR05 6 G6080 GR66 7 G0003 G09 8 G000 G09 5 Hex Sock et Head Plug W/ORing, 9 6"8 ORing ORing Plug W/ORing, ⅞" ORing ORing Hex Head Cap Screw, ⅜"6 x ½" Lock Washer, ⅜" Hex Head Cap Screw, ⅜"6 x ¼" Serrated Flange Nut, ⅜"6 9 GD36 Cover 0 G0977 Phillips Pan Head Machine Screw, No. 0 x ½", Stainless Steel GD738 Sleeve, " Long GD338 Insulated Clamp, 6" 3 GD330 Jumper, 7 6" G067 Phillips Pan Head Machine Screw, No. 83 x ¾", Stainless Steel 5 GA9097 GR635 Terminal Strip W/Screws, No. 6, Terminal Screw, No. 63 x ¼" 6 GA37 Terminal Strip, Mount 7 G066 Phillips Pan Head Machine Screw, No. 0 x ¾", Stainless Steel 8 G6800 GR66 9 G60808 GR037 0 G009 G003 G03 G386 6 GA358 Ground Clamp GD9533 Block Elbow W/ORing, 90, ⅞" Male JIC To ORing ORing Plug W/ORing, ¾"6 ORing ORing Hex Head Cap Screw, 5 6"8 x " Hex Head Cap Screw, 5 6"8 x ¾" Lock Washer, 5 6" Flat Washer, 5 6" SAE Rev. 9/ P6

226 Valve Block on L.H. Wing M0330 VVB030(FFc) C C V C3 P V V3 ITEM PART NO. QTY. DESCRIPTION GD9535 Block See Check Valve on page P53 3 See Pressure Relief Valves on page P53 G68008 GR037 5 G60806 GR05 6 G GR037 7 G66000 Swivel Tee, ⅞" JIC 8 G076 G07 G003 Elbow W/ORing, 90, ¾"6 Male JIC To ORing ORing Plug W/ORing, 9 6"8 ORing ORing Elbow W/ORing, 90, ⅞" Male JIC To ¾"6 ORing ORing Hex Head Cap Screw, ¼"0 x ¾" Lock Washer, ¼" Hex Nut, ¼"0 9 G Swivel Tee, ¾"6 JIC P7 Rev. 9/

227 M0330 Valve Block on L.H. and R.H. Wheel Module (FF03) 36 Row 0" Only ITEM PART NO. QTY. DESCRIPTION GA3 Block See Pressure Relief Valves on page P53 3 G60008 Connector W/ORing, ¾"6 Male JIC To ORing G0939 G09 G00 Hex Head Cap Screw, ⅜"6 x ¼" Lock Washer, ⅜" Hex Nut, ⅜"6 Pilot Pressure Booster Valve Block (IP85) 3 ITEM PART NO. QTY. DESCRIPTION GD58 Valve Block G GR037 Connector W/ORing, ⅞" Male JIC To ¾"6 ORing ORing 3 GA307 Pressure Relief Valve, 000 PSI G60080 Connector W/ORing, ⅞" Female JIC to ¾"6 ORing Rev. 9/ P8

228 Junction Block on Hose TakeUp M0330 (IP57) ITEM PART NO. QTY. DESCRIPTION GD9537 Junction Block G60008 GR037 3 G GR Connector W/ORing, ¾"6 Male JIC To ORing ORing Connector W/ORing, ⅞" Male JIC To ¾"6 ORing ORing G608H060 Hex Socket ORing Plug, 9 6" P9 Rev. 9/

229 M0330 Junction Block Located on L.H. Wing VVB038(HYD3a) ITEM PART NO. QTY. DESCRIPTION See Check Valve on page P53 G6000 GR65 3 G6000 GR66 GD37 Block Connector W/ORing, 7 6"0 Male JIC To ORing ORing Connector W/ORing, ⅞" Male JIC To ORing ORing Detent Lever Valve VVB033(FF) ITEM PART NO. QTY. DESCRIPTION GR5 Valve GR59 Bar 3 GR55 Bar G0060 G387 G006 Hex Head Cap Screw, 5 6"8 x ½" Flat Washer, ⅜" SAE Hex Nut, 5 6"8 5 GR56 Arm 6 GR58 Socket Shoulder Screw, ½" 7 GR57 Stainless Steel Bushing A GA678 Detent Lever Valve Complete B GR60 Seal Kit (For GR5 Valve), Includes: () BU Rings, (3) ORings Rev. 9/ P50

230 Pilot Operated Check Valve M0330 VVB039(HYD30) Not Used On L.H. Side Of Planter ITEM PART NO. QTY. DESCRIPTION G G Swivel Elbow, 90, ¾"6 Male JIC To Female Swivel Elbow, 5, ¾"6 Male JIC To Female G60008 GR037 3 Connector W/ORing, ¾"6 Male JIC To ORing ORing 3 GR55 Block (NonStock Item) GR07 GR037 3 Hex Socket Plug W/ORing ORing 5 G6000 GR65 Connector W/ORing, 7 6"0 Male JIC To ORing ORing 6 GR03 GR035 Hex Socket Plug W/ORing ORing 7 G006 G09 G00 Hex Head Cap Screw, ⅜"6 x 3" Lock Washer, ⅜" Hex Nut, ⅜"6 8 GR57 Pilot Piston (NonStock Item) 9 GR56 Cartridge (NonStock Item) A GA809 Pilot Operated Check Valve (Items 3,, 6, 8 And 9) B GR58 Seal Kit, Includes: () Cartridge Seal Kits, (5) ORings, () BU Rings Stroke Limiter Valve (FF3b) ITEM PART NO. QTY. DESCRIPTION A GA05 Stroke Limiter Valve Complete (Part Number Stamped On Valve Block) B GK55 Repair Kit, Includes: () Adapter, () Poppet, () Seal Kit W/ORings And BU Ring P5 Rev. 9/

231 M0330 Solenoid Valve (GK75) VVB09(TWL7c/TWL8/PLTR75c/A98) ITEM PART NO. QTY. DESCRIPTION GR076 Special Hex Nut, ½"0 GK7 GD959 GD9530 G GR0763 Cartridge Coil Kit W/Contacts, Housings And Fork Terminals Housing, Black Contact Fork Terminal Solenoid Valve Holds Load In One Direction A GK75 GD959 GD9530 G0996 Solenoid Valve Kit W/Solenoid Valve, Contacts, Housings And Fork Terminals Housing, Black Contact Fork Terminal B GR076 Seal Kit, Includes: () ORings, () BU Ring Fork Terminal Contact Housing Solenoid Valve (GK76) VVB09(FF5/TWL8/PLTR75c) Solenoid Valve Holds Load In Both Directions ITEM PART NO. QTY. DESCRIPTION GR3 Special Hex Nut, ½"0 GK7 GD959 GD9530 G GR3 Cartridge Coil Kit W/Contacts,Housings And Fork Terminals Housing, Black Contact Fork Terminal A GK76 GD959 GD9530 G0996 B GR0 Seal Kit Solenoid Valve Kit W/Housings, Contacts, And Forked Terminals Housing, Black Contact Fork Terminal Fork Terminal Contact Housing Rev. 9/ P5

232 Flow Control Valve M0330 VVB00(TWL8) ITEM PART NO. QTY. DESCRIPTION A GA33 Flow Control Valve B GR076 Seal Kit, Includes: () ORings, () BU Ring Pressure Relief Valves VVB00(FF6/FF6a/FF0) ITEM PART NO. QTY. DESCRIPTION GA88 Pressure Relief Valve, 500 PSI GR55 Seal Kit, Includes: () ORings, () BU Ring GA00 GR076 3 GA307 GR076 Pressure Relief Valve, 550 PSI Seal Kit, Includes: () ORings, () BU Ring Pressure Relief Valve, 000 PSI Seal Kit, Includes: () ORings, () BU Ring Check Valve VVB00(TWL30) ITEM PART NO. QTY. DESCRIPTION A GA93 Check Valve B GR076 Seal Kit, Includes: () ORings, () BU Ring P53 Rev. 9/

233 M0330 Clutch Valve Assembly (IP075) ITEM PART NO. QTY. DESCRIPTION GA357 G06 G00 Clutch Valve Bracket Serrated Flange Nut, ¼"0 Hex Head Cap Screw, ¼"0 x ½" GD990 G0960 Clutch Valve Cover Flanged Whiz Lock Screw, ¼"0 x ⅝", No Serration 3 G76 Hex Socket Head Cap Screw, ¼"0 X ¼" GR9 Solenoid Valve End Plate Kit 5 GD Pin Connector 6 GR93 Solenoid Clutch Valve 7 GD9080 Elbow, ¼" x ⅛" NPT Swivel 8 GD998 Elbow, ¼" Male Swivel Extended 9 GD756 Plug, ¼" NPT 0 GD78 Male Connector, ¼" A GA359 Clutch Valve Assembly (Items 8) Rev. 9/ P5

234 ASD Valve Block M0330 (IP09) ITEM PART NO. QTY. DESCRIPTION GD93 Block G GR037 3 GA93 Check Valve G GR037 Connector W/ORing, ⅞" Male JIC To ¾"6 ORing ORing Elbow W/ORing, 90, ⅞" Male JIC To ¾"6 ORing ORing 5 G6000 Connector W/ORing, 6" Male JIC To ⅞" ORIng 6 G6500 Swivel Elbow, 90, 6" Male JIC To Female 7 G60806 GR05 Plug W/ORing, 9 6"8 ORing ORing P55 Rev. 9/

235 This page left blank intentionally.

236 Hydraulic System, Row 0" M0330 (FF97a) Row Marker Cylinder Valve Block On R.H. Wing Valve Block On L.H. Wing Row Marker Cylinder Slave Cylinders Stroke Limiter Valve Master Cylinders Helper Cylinders Detent Lever Valve Master Cylinders Valve Block On Tower Assembly Valve Block On Front Hitch Tongue Cylinder Hitch Parallel Linkage Cylinder P57 Rev. 9/

237 M0330 Hydraulic System, Row 0" ITEM PART NO. QTY. DESCRIPTION *A0 Hose Assembly, ⅜" x 3" *A Hose Assembly, ½" x 30" 3 *A99 3 Hose Assembly, ½" x 80" *A98 Hose Assembly, ½" x 5" 5 *A089 Hose Assembly, ⅜" x 0" 6 *A87 Hose Assembly, ½" x 50" 7 *A396 Hose Assembly, ⅜" x 0" 8 *A0 Hose Assembly, ½" x " 9 *A07 Hose Assembly, ⅜" x 8" 0 G Tee, ¾"6 Male JIC *A09 Hose Assembly, ⅜" x 60" G65006 Cross, 9/6"8 Male JIC 3 *A39 8 Hose Assembly, ⅜" x 36" *A00 Hose Assembly, ⅜" x 8" 5 G Swivel Elbow, 90, ¾"6 Male JIC To Female 6 *A00 Hose Assembly, ⅜" x 0" 7 *A37 Hose Assembly, ⅜" x 0 8 *A6 Hose Assembly, ¼" x " 9 *A89 Hose Assembly, ¼" x 36" 0 *A06 Hose Assembly, ⅜" x 8" *A Hose Assembly, ½" x 30" GD086 ISO Coupler 3 G GR037 Connector W/ORing, 9/6"8 Male JIC To ¾"6 ORing ORing G65006 Swivel Elbow, 5, 9/6"8 Male JIC To Female 5 G6030 Tee, ⅞" Male JIC 6 G65000 Swivel Elbow, 90, ⅞" Male JIC To Female 7 *A05 Hose Assembly, ⅜" x 8 8 *A39 Hose Assembly, ⅜" x 36" 9 *A00 Hose Assembly, ⅜" x 0" 30 *G Swivel Elbow, 90, 9/6"8 Male JIC To Female 3 G Reducer, ¾"6 Female JIC To 9/6"8 Male JIC *Hydraulic hose is not stocked by Kinze Repair Parts, but can be made available on a special order basis. Call for quote. Rev. 9/ P58

238 Hydraulic System, Row 30" M0330 (IPa) 9 9 Marker Cylinder 6 Pilot Operated Check Valve on R.H. Wing 3 Marker Cylinder Helper Cylinders Tongue Cylinder Pilot Pressure Booster Valve Block Junction Block on L.H. Wing Detent Lever Valve Slave Cylinders Valve Block on L.H. Wing Stroke Limiter Valve Valve Block on Front Hitch Tongue Lift Cylinder Master Cylinders Pilot Operated Check Valve on L.H. Wing Master Cylinders Valve Block on R.H. Wing Valve Block on Tower Assembly P59 Rev. 9/

239 M0330 Hydraulic System, Row 30" ITEM PART NO. QTY. DESCRIPTION G Connector W/ORing, 9 6"8 Male JIC To ¾"6 ORing GR037 ORing G Elbow W/ORing, 90, ¾"6 Male JIC To ORing GR037 ORing 3 *A073 Hose Assembly, ⅜" x 8" G Swivel Elbow, 5, ¾"6 Male JIC To Female 5 G65006 Cross, 9 6"8 Male JIC 6 G60308 Tee, ¾"6 Male JIC 7 *A8500 Hose Assembly, 3 6" x 60" 8 *A89 Hose Assembly, ¼" x 36" 9 *A6 Hose Assembly, ¼" x " 0 G GR037 Connector W/ORing, 9 6"8 Male JIC To ¾"6 ORing ORing G65006 Swivel Elbow, 5, 9 6"8 Male JIC To Female *A0 Hose Assembly, ⅜" x 3" 3 *A30 Hose Assembly, ⅜" x 9" *A39 8 Hose Assembly, ⅜" x 36" 5 *A3 Hose Assembly, ⅜" x 00" 6 *A03 Hose Assembly, ⅜" x 3" 7 *A36 Hose Assembly, ⅜" x 0" 8 *A399 Hose Assembly, ⅜" x 6" 9 *A80 Hose Assembly, ½" x 90" 0 *A000 Hose Assembly, ⅜" x 58" G Swivel Elbow, 90, ¾"6 Male JIC To 9 6"8 Female *A Hose Assembly, ½" x 30" 3 *A85 3 Hose Assembly, ½" x 330" *A808 Hose Assembly, ½" x 37" 5 *A873 Hose Assembly, ½" x " 6 *A79 Hose Assembly, ½" x 98" 7 *A65 Hose Assembly, ½" x 8" 8 G Reducer, ¾"6 Female JIC To 9 6"8 Male JIC 9 *A07 Hose Assembly, ⅜" x 8" 30 *A850 Hose Assembly, 3 6" x 6" 3 *A08 3 Hose Assembly, ⅜" x 8" 3 G Swivel Elbow, 90, 9 6"8 Male JIC To Female 33 GD086 ISO Coupler 3 *A883 Hose Assembly, ½ x 58" *Hydraulic hose is not stocked by Kinze Repair Parts, but can be made available on a special order basis. Call for quote. Rev. 9/ P60

240 Hydraulic System, 36 Row 0" M0330 (IP79) To Marker Cylinder 30 6 Pilot Operated Check Valve on R.H. Wing 9 Master Cylinder Valve Block on R.H. Wing 36 Valve Block on R.H. Wheel Module Master Cylinder Assist Cylinder Helper Cylinders Tongue Cylinder 5 8 Valve Block on Tower Assembly 7 7 Detent Lever Valve Valve Block on Front Hitch Slave Cylinders 5 3 Pilot Pressure Booster Valve Block 3 Junction Block on L.H. Wing 0 Valve Block on L.H. Wing 7 6 Stroke Limiter Valve 3 Hitch Paralled Linkage Cylinder Master Cylinder 6 3 Assist Cylinder 8 Master Cylinder 30 To Marker Cylinder 30 P6 Rev. 9/

241 M0330 Hydraulic System, 36 Row 0" ITEM PART NO. QTY. DESCRIPTION 8 G GR037 G68008 GR037 Connector W/ORing, 9 6"8 Male JIC To ¾"6 ORing ORing Elbow W/ORing, 90, ¾"6 Male JIC To ORing ORing 3 *A098 Hose Assembly, ⅜" x 6" G Swivel Elbow, 5, ¾"6 Male JIC To Female 5 G65006 Cross, 9 6"8 Male JIC 6 G60308 Tee, ¾"6 Male JIC 7 *A08 Hose Assembly, ⅜" x 8" 8 *A89 Hose Assembly, ¼" x 36" 9 *A6 Hose Assembly, ¼" x " 0 G GR037 Connector W/ORing, 9 6"8 Male JIC To ¾"6 ORing ORing G65006 Swivel Elbow, 5, 9 6"8 Male JIC To Female *A0 Hose Assembly, ⅜" x 3" 3 *A30 Hose Assembly, ⅜" x 9" *A39 6 Hose Assembly, ⅜" x 36" 5 *A3 Hose Assembly, ⅜" x 00" 6 *A03 Hose Assembly, ⅜" x 3" 7 *A057 Hose Assembly, ⅜" x 6" 8 *A399 Hose Assembly, ⅜" x 6" 9 *A80 Hose Assembly, ½" x 90" 0 *A000 Hose Assembly, ⅜" x 58" G Swivel Elbow, 90, ¾"6 Male JIC To Female *A Hose Assembly, ½" x 30" 3 *A85 3 Hose Assembly, ½" x 330" *A808 Hose Assembly, ½" x 37" 5 *A873 Hose Assembly, ½" x " 6 *A79 Hose Assembly, ½" x 98" 7 *A65 Hose Assembly, ½" x 8" 8 G66008 Swivel Tee, ¾"6 JIC 9 *A09 Hose Assembly, ⅜" x " 30 G0808 Plug, ¾"6 JIC 3 *A378 Hose Assembly, ⅜" x 536" 3 *A8503 Hose Assembly, 3 6" x 36" 33 *A850 Hose Assembly, 3 6" x 70" 3 G Reducer, ¾"6 Female JIC To 9 6"8 Male JIC 35 *A083 Hose Assembly, ⅜" x 36" 36 *A3 Hose Assembly, ⅜" x 0½" 37 *A883 Hose Assembly, ½ x 58" 38 G Swivel Elbow, 90, 9 6"8 Male JIC To Female *Hydraulic hose is not stocked by Kinze Repair Parts, but can be made available on a special order basis. Call for quote. Rev. 9/ P6

242 Electrical Components M0330 Amber Red See Light/Reflective Decal Brackets and Extensions on page P66 Socket Contact Pin Contact Sealing (Tractor) (Planter) Plug Amber For Planter Harness For Tractor Harness Harness Between Solenoid Valve And Valve Block On R.H. Wing Planter Harness A B C WHT BLK GRN GRN BLK WHT C B A Harness Extension Tractor Harness P63 Rev. 9/

243 M0330 Electrical Components ITEM PART NO. QTY. DESCRIPTION GA98 G0996 Jumper Wire W/Fork Terminal, 3" Fork Terminal GD330 Jumper, 7 6" 3 GD870 Socket Contact, No. GD87 Pin Contact, No. 5 GD8739 Sealing Plug, No. 6 GA609 Connector W/Cable Clamp, 3 Pin Capacity 7 GA786 Dust Cap W/Chain 8 GA7863 Dust Cap W/Chain 9 GA608 Connector W/Cable Clamp, 3 Socket Capacity 0 GK8 3Pin Female Connector Kit (Black), Includes: (3) 3Pin Female Housings, (9) Pin Contacts, (9) Seals GK5 3Pin Male Connector Kit (Black), Includes: (3) 3Pin Male Housings, (9) Socket Contacts, (9) Seals GD089 Sealing Plug 3 GA807 Dust Plug (Black) GA953 Wiring Harness, 3", From Valve Block On R.H. Wing To Tower Assembly 5 GA996 Wiring Harness W/Dust Cap, 68" 6 GA736 Harness Extension W/Dust Caps, 80" 7 GA670 GR0 GR06 GR07 GR08 8 GA6699 GA6700 GR03 GR0 GR05 GR06 GR07 GR08 9 G006 G0857 G00 0 GA950 GA5385 G7633X G7639X Single Amber Light Assembly Amber Lens Rubber Grommet () Lamp Unit Bulb Double Light Assembly Double Light Assembly (Shown) Red Lens Amber Lens Cover Rubber Grommet () Lamp Unit Bulb Hex Head Cap Screw, ¼"0 x " Hex Head Cap Screw, ¼"0 x ¼" Lock Nut, ¼"0, Grade B Wiring Harness W/7 Terminal Female Connector, 659" ( Light Connections) 7 Terminal Female Connector Backlit Control Console Assembly W/Mounting Brackets, Short Harness W/Dust Cap And Power Cable (Shown) Backlit Control Console Assembly W/Mounting Brackets, Short Harness W/Dust Cap And Power Cable, Planters Equipped With TwoSpeed Point Row Clutches GA6 35 Fuse Holder W/Spade, 33 50" 3 GA7077 Indicator Light GD89 Fuse, 5 Amp, Type AGC 5 GD03 6 Fuse, MDL 0 Amp Delay Action 6 GR363 5 Hex Face Nut, 5 3"3 GR36 5 Internal Tooth Lock Washer, 5 3" 7 GA873 Cover Plate (Shown) GA8735 Cover Plate, Planters Equipped With TwoSpeed Point Row Clutches 8 GR9 Pan Head Screw, No. 83 x ½" 9 GD3860 ORing (If Applicable) 30 GA58 Switch, 3 Position Toggle, OnOffOn 3 GA6978 Switch, 3 Position Toggle, Momentary OnOffMomentary On Rev. 9/ P6

244 Electrical Components M0330 ITEM PART NO. QTY. DESCRIPTION 3 GA6977 Switch, Position Toggle, OnOff 33 GA873 Switch, Push Button W/Transformer 3 GD9896 Mounting Bracket 35 G385 Flat Washer, ¼" SAE 36 GA6975 Knob 37 GR90 Cage Nut, ¼"0 38 GK67 Power Lead Adapter Connector Kit, Includes: () 3Pin Connector, () Cable Clamp, (3) Male Terminal Pins 39 GK68 Console Cable Connector Kit, Includes: () 3Pin Connector, () Cable Clamp, () Lock Ring, (3) Female Terminal Pins 0 GA7856 Power Lead Adapter GA879 Wiring Harness W/Dust Cap And Power Cable GA7855 Extension, 30' NOTE: See Point Row Clutch on page P3 or See TwoSpeed Point Row Clutch on page P5 for R.H. and L.H. Wiring Harnesses for the point row clutches. See display unit for those components. P65 Rev. 9/

245 M0330 Light/Reflective Decal Brackets and Extensions (RU30b/RU9/RU33/RU3/RU30a/RU3/RU9a/RU3a ITEM PART NO. QTY. DESCRIPTION G03 Carriage Bolt, 5 6"8 x ¾" G060 Serrated Flange Nut, 5 6"8 G006 G00 Hex Head Cap Screw, ¼"0 x " Hex Nut, ¼"0 3 GD5968 Light Mount Extension GD75 GD7 Bracket (L.H. Wing) Bracket (R.H. Wing) (Shown) 5 GD5967 Reflective Decal Bracket 6 GD3358 Light Bracket 7 GD7039 G030 G00 UBolt, 7" x 7" x ⅝" Lock Washer, ⅝" Hex Nut, ⅝" 8 GD73 Light Mount Extension 9 GD70 Reflective Decal Bracket Rev. 9/ P66

246 KPM III Electronic Seed Monitor M0330 (MTR3w) Radar Distance Sensor Magnetic Distance Sensor (MDS) Shaft Rotation Sensor Power Lead Adapter Radar YCable Adapter Harness Blue Extension Harness Junction YHarness Planter Harness Acre Counter Switch Kit Blue Blue Magnetic Distance Sensor (MDS) Adapter P67 Rev. 9/

247 M0330 KPM III Electronic Seed Monitor ITEM PART NO. QTY. DESCRIPTION GA7858 Radar Distance Sensor W/0' Cable GA806 Radar Sensor Pipe/Mounting Bracket Package 3 GK33 Pin Connector Kit W/Female Housing, Includes: () Pins, () Cable Clamp GA5600 Magnetic Distance Sensor 5 GD875 Magnetic Distance Sensor Pulse Wheel 6 GD69 Insulated Clamp, ⅜" 7 GD8770 Bracket 8 G000 G09 G00 Hex Head Cap Screw, ⅜"6 x " Lock Washer, ⅜" Hex Nut, ⅜"6 9 GD877 Spring Wave Washer 0 GA7856 Power Lead Adapter GA9 Monitor/Radar Adapter Cable, 0" GK67 Power Lead Adapter Connector Kit, Includes: () Cable Clamp, () 3Pin Connector, (3) Male Terminal Pins 3 GK68 Console Cable Connector Kit, Includes: () Cable Clamp, () 3Pin Connector, () Lock Ring, (3) Female Terminal Pins GA039 GA03 GR76 KPM III Backlit Console W/Brush (Item 3), Dust Plug (Item 3), Mounting Bracket Assembly, Console Mounting Bracket Hardware And Power Harness Mounting Bracket Assembly, Includes: () Mounting Brackets, () Connector Halves, () Compression Spring, () Tension Knob, () ¼"0 x ¾" Hex Head Cap Screw, () ¼" Plastic Washer, () ¼" Steel Washer Console Mounting Bracket Hardware Package, Includes: (3) No. 03 x ⅝" Hex GR76 Socket Pan Head Screws, (3) No. 0 Lock Washers Power Harness 5 GK3 Pin Connector Kit W/Male Housing, () Female Socket Contacts and () Cable Clamp 6 Included In Tractor/Planter Wiring Harness, See Electrical Components on page P63 7 GA785 GA8050 GD993 8 GA66 GR785 GA636 Planter Harness W/Dust Caps, 6 Row (0 Connectors) Planter Harness W/Dust Caps, 8 Row ( Connectors) Dust Cap Seed Tube W/Computerized Sensor (EdgeVac) Sensor Only, EdgeVac Seed Tube (With Holes For Sensor Installation)(EdgeVac) 9 GA7859 Magnetic Distance Sensor Adapter (Analog To Digital) 0 GR059 Brush GR0586 Radar YCable (Used To Connect Radar Distance Sensor For Multiple Functions) GA7857 Adapter Harness, ' 3 GA785 GA7855 GD993 GA7853 GD993 Extension Harness W/Dust Cap, 5' Extension Harness W/Dust Cap, 30' Dust Cap Junction YHarness W/Dust Cap Dust Cap 5 GK3 Pin Female Connector Kit (Black), Includes: (3) Pin Female Housings, (6) Pin Contacts, (6) Seals 6 GK30 Pin Male Connector Kit (Black), Includes: (3) Pin Male Housings, (6) Socket Contacts, (6) Seals Rev. 9/ P68

248 KPM III Electronic Seed Monitor M0330 ITEM PART NO. QTY. DESCRIPTION 7 GK8 GK36 3Pin Female Connector Kit (Black), Includes: (3) 3Pin Female Housings, (9) Pin Contacts, (9) Seals 3Pin Female Connector Kit (Blue), Includes: (3) 3Pin Female Housings, (9) Pin Contacts, (9) Seals 8 GK5 GK363 3Pin Male Connector Kit (Black), Includes: (3) 3Pin Male Housings, (9) Socket Contacts, (9) Seals 3Pin Male Connector Kit (Blue), Includes: (3) 3Pin Male Housings, (9) Socket Contacts, (9) Seals 9 GD089 Sealing Plug 30 GK9 Acre Counter Switch Kit 3 GA806 GA GA807 GA9979 Dust Plug (Black) Dust Plug (Blue) Dust Plug (Black) Dust Plug (Blue) 33 GR5 Rotation Sensor 3 GR Actuator 35 GD7 Cover 36 G097 G093 G GD868 Mount 38 G0686 G09 G00 Pan Head Machine Screw, No. 83 x ¼", Stainless Steel Lock Washer, No. 8, Internal/External, Stainless Steel Hex Nut, No. 83, Stainless Steel Hex Head Cap Screw, ⅜"6 x 8" Lock Washer, ⅜" Hex Nut, ⅜"6 39 GD88 Shaft Sensor Mount 0 G88 G03 G0758 GA GR99 GA090 Pan Head Screw, No. 03 x ½" Washer, No. 0 SAE Hex Nut, No. 03 Seed Tube W/Computerized Sensor (Mechanical) Sensor Only (Mechanical) Seed Tube (W/Holes for Sensor Installation)(Mechanical) A GA67 Magnetic Distance Sensor And Mounting Package (Items 9) B GA35 Shaft Sensor Mounting Package (Items 350) C GA835 Shaft Rotation Kit, Includes: () Actuators () Rotation Sensors P69 Rev. 9/

249 This page left blank intentionally.

250 Planter Monitor Module (PMM) M0330 (MTR60/MTR63/PMM0/MTR65/MTR6/MTR6/MTR6/PMM0) Shaft Rotation Sensor 0 Magnetic Distance Sensor (MDS) 3 5 Planter Harness Blue Blue Magnetic Distance Sensor (MDS) Adapter P7 Rev. 9/

251 M0330 Planter Monitor Module (PMM) ITEM PART NO. QTY. DESCRIPTION G0686 G09 G00 Hex Head Cap Screw, ⅜"6 x 8" Lock Washer, ⅜" Hex Nut, ⅜"6 GD88 Shaft Sensor Mount 3 GR5 Rotation Sensor GR Actuator 5 GD868 Mount 6 G0757 G03 G GD7 Cover 8 G097 G093 G098 Pan Head Screw, No. 03 x ¼" Washer, No. 0 SAE Hex Nut, No. 03 Pan Head Machine Screw, No. 83 x ¼", Stainless Steel Lock Washer, No. 8, Internal/External, Stainless Steel Hex Nut, No. 83, Stainless Steel 9 GA5600 Magnetic Distance Sensor 0 GD875 Magnetic Distance Sensor Pulse Wheel GD69 Insulated Clamp, ⅜" G000 G09 G00 Hex Head Cap Screw, ⅜"6 x " Lock Washer, ⅜" Hex Nut, ⅜"6 3 GD8770 Bracket GD877 Spring Wave Washer 5 GA806 GA9978 Dust Plug (Black) Dust Plug (Blue) 6 GA807 GA9979 Dust Plug (Black) Dust Plug (Blue) 7 GK8 GK36 8 GK5 GK363 9 GD089 Sealing Plug 0 GD803 G003 GD9630 G Pin Female Connector Kit (Black), Includes: (3) 3Pin Female Housings, (9) Pin Contacts, (9) Seals 3Pin Female Connector Kit (Blue), Includes: (3) 3Pin Female Housings, (9) Pin Contacts, (9) Seals 3Pin Male Connector Kit (Black), Includes: (3) 3Pin Male Housings, (9) Socket Contacts, (9) Seals 3Pin Male Connector Kit (Blue), Includes: (3) 3Pin Male Housings, (9) Socket Contacts, (9) Seals Bracket Hex Head Cap Screw, 5 6"8 x ¾" Spacer, 6" Serrated Flange Nut, 5 6"8 GA538 G099 Planter Monitor Module Hex Head Cap Screw, 5 6"8 x ⅞" GD9759 Module Bracket Mount 3 GD890 Tap Block, Long GA563 Module Cover Assembly W/Lock Clamps 5 G05 Hex Head Cap Screw, ⅝" x 9" 6 GA655 Implement Cable (6 Row) 7 GR059 Brush 8 GA785 GA8050 GD993 Planter Harness W/Dust Caps, Row (6 Connectors) Planter Harness W/Dust Caps, 36 Row (8 Connectors) Dust Cap 9 GA66 GR785 GA636 Seed Tube W/Computerized Sensor (EdgeVac) Sensor Only (EdgeVac) Seed Tube (With Holes For Sensor Installation) (EdgeVac) 30 GA7859 Magnetic Distance Sensor Adapter (Analog To Digital) 3 GA557 Planter Monitor Cable 3 GA GR99 GA090 Seed Tube W/Computerized Sensor (Mechanical) Sensor Only (Mechanical) Seed Tube (W/Holes for Sensor Installation)(Mechanical) A GA67 Magnetic Distance Sensor And Mounting Package (Items 9) Rev. 9/ P7

252 Kinze Cobalt Display M0330 (COa/VI8/VI/A553/GR96/GR839/A85/A853) P73 Rev. 9/

253 M0330 Kinze Cobalt Display ITEM PART NO. QTY. DESCRIPTION GA355 Cobalt Display GA85 Power Supply 3 GA365 Adapter Cable GR835 Flash Card 5 GR836 SMS CD 6 GA55 Display Cable 7 GA56 Power Cable 8 GA50 Power Control Relay 9 GA598 Seed Rate Power Cable 0 GA596 Radar Adapter Cable GA539 Switch Box Module GR838 Dust Plug 3 GR839 Dust Plug GA868 Ram Double Socket Arm 5 GA537 Clutch Control Module 6 GA555 GA655 Implement Cable ( Row) Implement Cable (6 Row) 7 GA3530 Clutch Control Cable 8 GA558 Can Stub Cable, 8'' 9 GA559 Can Extension, 5'' 0 GA353 Implement Switch Extension Cable GD877 Terminator GR96 Switch Box Bracket GA538 Planter Monitor Module 5 GA557 Planter Monitor Cable 6 GD876 YSplice Connector 7 See Shank Assembly, Seed Tube, and Depth Adjustment on page P 8 See Clutch Valve Assembly on page P5 9 See Airline Fittings and Hoses, Row 30" on page P9 See Airline Fittings and Hoses, 36 Row 0" on page P0 30 GD808 Ram Vesa Base 3 GD807 Ram Base Rev. 9/ P7

254 Kinze Vision Display M0330 (VI50b/VI8/VI/A553/GR96/GR839/A85/A853) P75 Rev. 9/

255 M0330 Kinze Vision Display ITEM PART NO. QTY. DESCRIPTION GA536 Vision Loaner (Display Only) GA85 Power Supply 3 GA853 Null Modem Cable GR835 Flash Card 5 GR836 SMS CD 6 GA55 Display Cable 7 GA56 Power Cable 8 GA50 Power Control Relay 9 GA598 Seed Rate Power Cable 0 GA596 Radar Adapter Cable GA539 Switch Box Module GR838 Dust Plug 3 GR839 Dust Plug GA868 Ram Double Socket Arm Assembly 5 GA537 Clutch Control Module 6 GA555 GA655 Implement Cable ( Row) Implement Cable (6 Row) 7 GA3530 Clutch Control Cable 8 GA558 Can Stub Cable, 8'' 9 GA559 Can Extension, 5'' 0 GA353 Implement Switch Extension Cable See Airline Fittings and Hoses, Row 30" on page P9 See Airline Fittings and Hoses, 36 Row 0" on page P0 GR96 Switch Box Bracket GA538 Planter Monitor Module 5 GA557 Planter Monitor Cable 6 See Clutch Valve Assembly on page P5 7 See Shank Assembly, Seed Tube, and Depth Adjustment on page P 8 GA553 GPS Cable 9 GA55 GPS Antenna 30 GD876 YSplice Connector 3 GD877 Terminator 3 GD808 Ram Vesa Base 33 GD807 Ram Base A G866X Vision Display Package (Items 5) Rev. 9/ P76

256 B A C B A C TM Integra Display M0330 (IP96) CABLES 3 AIR LINES Air Valves Sections 0 5 Air Valves Sections Section Section Section 3 Section Section 5 Section 6 Section 7 Section P77 Rev. 9/

257 M0330 Integra Display ITEM PART NO. QTY. DESCRIPTION GA7 Integra Display GA539 Switch Box Module 3 GR96 Switch Box Bracket GA868 Ram Double Socket Arm Assembly 5 GA85 Power Supply 6 GA9 Flash Drive 7 GR836 SMS CD 8 GA5 Integra Display Cable 9 GA5 Power Cable 0 GA598 Seed Rate Power Cable GD876 3 YSplice Connector GA50 Can Adapter Cable 3 GA596 Radar Adapter Cable GA50 Power Control Relay 5 GA30 Implement Cable, 6 Row 6 GA538 Planter Monitor Module 7 GA557 Planter Monitor Cable 8 GA567 Can Extension Cable, " 9 GA566 Can Stub Cable, 6" 0 GA537 Clutch Control Module GA556 Seed Command Cable GA307 Implement Switch Extension Cable 3 See Shank Assembly, Seed Tube, and Depth Adjustment on page P GA30 Hall Effect Sensor 5 See Clutch Valve Assembly on page P5 6 GR838 Dust Plug 7 GR839 Dust Plug 8 GA55 GPS Antenna 9 GA553 GPS Cable 30 GA853 Null Modem Cable 3 GA356 Cable Extension, 80" 3 See Airline Fittings and Hoses, Row 30" on page P9 See Airline Fittings and Hoses, 36 Row 0" on page P0 33 GD808 Ram Vesa Base 3 GD807 Ram Base Rev. 9/ P78

258 Liquid Fertilizer Piston Pump Drive M0330 (FFa) 0 Tooth Drive Sprocket And 8 Tooth Driven Sprocket Model NGP6055 Piston Pump ITEM PART NO. QTY. (Per Assy.) GA597 GA75 GD7889 G058 G389 G08 G00 G00 G39 G030 G00 GD05 GA78 G0779 DESCRIPTION Idler W/Sprocket, Bushing, Spacer And Hardware Sprocket W/Bearing, 8 Tooth Bushing, " O.D. x 9 6" I.D x 7 6" Long Hex Head Cap Screw, ½"3 x ¼" Flat Washer, ½" SAE Lock Washer, ½" Hex Nut, ½"3 Hex Head Cap Screw, ⅝" x 5½" Flat Washer, ⅝" SAE Lock Washer, ⅝" Hex Nut, ⅝" Spacer, ¾" Idler Arm Grease Fitting, 90, ¼"8 G060 Spring Pin, ¼" x ½" 3 G033 5 Machine Bushing, ", 0 Gauge G3309 GR09 GR09 Chain, No. 0, 9 Pitch Including Connector Link And Offset Link Connector Link, No. 0 Offset Link, No. 0 P79 Rev. 9/

259 M0330 Liquid Fertilizer Piston Pump Drive ITEM PART NO. QTY. DESCRIPTION (Per Assy.) 5 GA780 Sprocket, 0 Tooth 6 GD685.5 Hex Shaft, ⅞" x ¼" ( Holes) 7 GD5857 Spring 8 G0093 G030 G00 9 G030 G386 G03 G Hex Head Cap Screw, ⅝" x 8½" Lock Washer, ⅝" Hex Nut, ⅝" Carriage Bolt, 5 6"8 x ⅞" Flat Washer, 5 6" SAE Lock Washer, 5 6" Hex Nut, 5 6"8 0 G0003 Bearing, ⅞" Hex Bore, Spherical G3000 Flangette G000 G387 G09 G00 Hex Head Cap Screw, ⅜"6 x ¼" Flat Washer, ⅜" SAE Lock Washer, ⅜" Hex Nut, ⅜"6 3 GD556 Scraper G0053 G389 G00 Hex Head Cap Screw, ½"3 x ½" Flat Washer, ½" SAE Hex Nut, ½"3 5 GD000 Sleeve, ¾" Long 6 GA5090 GD5753 GD575 Tire And Rim Assembly (Specify Brand*) Tire,.0" x 6" (Specify Brand*) Inner Tube 7 See Liquid Fertilizer Piston Pump, NGP6055 on page P85 8 GA76 Base Mount 9 GD558 Lynch Pin, ¼" 0 GA068 Spring W/Plug GA75 G06 Pump Mount W/Grease Fitting Grease Fitting, ⅛" NPT GD89 G030 G00 UBolt, 7" x " x ⅝" Lock Washer, ⅝" Hex Nut, ⅝" 3 GD00 Sleeve, 7 6" G006 G09 G00 Hex Head Cap Screw, ⅜"6 x 3" Lock Washer, ⅜" Hex Nut, ⅜"6 5 G0003 G387 GR G09 G00 Hex Head Cap Screw, ⅜"6 x ½" Flat Washer, ⅜" SAE Mounting Pad Lock Washer, ⅜" Hex Nut, ⅜"6 6 GD55 Pump Mount 7 G078 G009 Clevis Pin, 5 6" x " Retaining Ring, 5 6" 8 See Liquid Fertilizer Piston Pump, NGP6055 on page P85 9 GA66 Idler Mounting Bracket 30 G00 Hex Head Cap Screw, 5 6"8 x " 3 G009 Hex Head Cap Screw, 5 6"8 x " 3 GD8065 Guide 33 GD977 Sleeve, ⅞" Long * Specific brand requests will be supplied only as available from current Kinze Repair Parts stock. If a specific brand requested is not in stock, the brand available will be supplied. Different brand tires may have different diameters. Change in tire brand may affect rates. Field checks are recommended after any change in contact tires Rev. 9/ P80

260 Liquid Fertilizer Piston Pump Mount and Ground Drive Wheel M0330 (TWL37a) 8 Tooth Sprocket 8 Tooth Sprocket ITEM PART NO. QTY. DESCRIPTION G05 G030 G Hex Head Cap Screw, ⅝" x 9" Lock Washer, ⅝" Hex Nut, ⅝" GA0355 Wheel Arm Mount 3 GB08 Bushing, 3" I.D. x ⅞" O.D. x 9 3" Long G0005 G39 G007 5 GA97 Spring Mount 6 GD68 G060 7 GA06 G06 Hex Head Cap Screw, ⅝" x ¾" Flat Washer, ⅝" SAE Lock Nut, ⅝" Pin, ¼" x 3 ½" Cotter Pin, ¼" x " Arm W/Grease Fittings Grease Fitting, ⅛" NPT P8 Rev. 9/

261 M0330 Liquid Fertilizer Piston Pump Mount and Ground Drive Wheel ITEM PART NO. QTY. DESCRIPTION 8 GA0 Wheel, 5" x 5" 9 GD66 Valve Stem 0 G00 G39 Hex Head Cap Screw, ⅝" x 6½" Flat Washer, ⅝" SAE GA0908 Spring Mount GB096 Washer 3 GD783 Compression Spring GA0907 Spring Guide 5 G G007 6 G006 G03 7 G0 G03 G005 Hex Head Cap Screw, ⅝" x " Lock Nut, ⅝" Hex Head Cap Screw, ¾"0 x " Lock Washer, ¾" Hex Head Cap Screw, ¾"0 x ¾" Lock Washer, ¾" Hex Nut, ¾"0 8 GD37 Hose Holder 9 GR6 Sprocket, 8 Tooth 0 See Liquid Fertilizer Piston Pump, NGP7055 on page P87 GD558 Lynch Pin, ¼" G0007 G39 G030 G00 3 GA089 Pump Mount G007 G389 G08 G00 5 GD338 Scraper 6 G003 G39 G030 G00 Hex Head Cap Screw, ⅝" x ½" Flat Washer, ⅝" SAE Lock Washer, ⅝" Hex Nut, ⅝" Hex Head Cap Screw, ½"3 x ½" Flat Washer, ½" SAE Lock Washer, ½" Hex Nut, ½"3 Hex Head Cap Screw, ⅝" x 3½" Flat Washer, ⅝" SAE Lock Washer, ⅝" Hex Nut, ⅝" 7 GA06 Idler Sprocket W/Bearing, 5 Tooth 8 GD78705 Spacer, 6" I.D. x ¼" Long 9 GD08 Tire, 7.60" x 5", 8 Ply (Specify Brand*) 30 GA559 Spindle 3 GA05 Seal 3 GA05 Bearing 33 GR067 5 Lug Nut, ½"0 3 G5008 Sprocket, 8 Tooth 35 G009 G03 Hex Head Cap Screw, 5 6"8 x " Lock Washer, 5 6" 36 GD083 Shoulder Nut, ¼" UNFA 37 GA057 GR090 GR00 38 G30063 GR095 GR000 5 Hub W/Cups And Studs, 5 Bolt Cup Stud Chain, No. 050, 63 Pitch Including Connector Link Connector Link, No. 050 Offset Link, No. 050 *Specific brand requests will be supplied only as available from current Kinze Repair Parts stock. If a specific brand requested is not in stock, the brand available will be supplied. Different brand tires may have different diameters. Change in tire brand may affect rates. Field checks are recommended after any change in tires. Rev. 9/ P8

262 Liquid Fertilizer Hoses and Fittings M0330 (FF8c/FF8cc) P83 Rev. 9/

263 M0330 Liquid Fertilizer Hoses and Fittings ITEM PART NO. QTY. DESCRIPTION G3008 Hose, ⅜" x 50', And 36 Row G068 Hose Clamp, No. 6 3 GD700 8 Adapter, ¼" NPT To ⅜" Barb See Liquid Fertilizer Piston Pump Flow Divider on page P89 5 G09 Pipe Plug, ¼" NPT 6 GA657 Mount, ¾" NPT 7 GD08 Bar 8 G05 G030 G00 Hex Head Cap Screw, ⅝" x 9" Lock Washer, ⅝" Hex Nut, ⅝" 9 G0733 Elbow, 90, ¾" Female NPT 0 G073 Adapter, ¾" NPT To Barb G050 Hose, ¾" x 00" G37 Reducing Bushing, ½" Male NPT To ¾" Female 3 GA3893 GR0880 GR088 GR088 GR0883 Strainer Complete Screen, No. 0 Mesh Gasket YBody End Cap G078 Hose Clamp, No. 6 5 See Liquid Fertilizer Piston Pump, NGP6055 on page P85 See Liquid Fertilizer Piston Pump, NGP7055 on page P87 6 G065 Reducing Bushing, ½" Male NPT To ¼" Female 7 G0887 Elbow, 90, ¼" Male NPT To Female 8 G069 Close Nipple, ¼" NPT 9 GA976 GR05 GR06 GR07 GR08 GR09 Shutoff Valve, ¼" NPT Body ORing Stem ORing Teflon Seat Ball Handle 0 G066 Adapter, ¼" NPT To Barb G067 Hose Clamp, No. G000 Hose, ¼" x ' 3 G0633 Tee, ¼" Barb G097 Elbow, 90, ¾" NPT To Barb Rev. 9/ P8

264 Liquid Fertilizer Piston Pump, NGP6055 M0330 (A335a/GR808) P85 Rev. 9/

265 M0330 Liquid Fertilizer Piston Pump, NGP6055 ITEM PART NO. QTY. DESCRIPTION GR80 G099 Flange Cover Assembly Hex Head Cap Screw, 5 6"8 x ⅞" GR80 Connecting Rod Assembly 3 GR80 G Spacer Assembly Hex Socket Head Set Screw, 5 6"8 x ⅜" GR3 Plug 5 GR53 Vent Plug 6 GR Woodruff Key 7 GR0 Eccentric Pin 8 GR Pin 9 GR0 Bearing 0. GR805 Setting Hub Assembly GR3 Stuffing Box Insert GR389 Sprocket, 8 Tooth 3 GR808 Adjustment Wrench GR806 Setting Pointer Assembly 5 GR795 Repair Kit, Includes: (6) Gaskets, (9) ORings, () Washers, () Retaining Ring, () Oil Seals, () Snap Ring, () Thrust Washer, () Rod Bushing, () Flange Plunger Packings, () Packing Springs, () Rod Vee Packing Sets 6 GR799 Discharge Valve Assembly 7 GR797 Suction Valve Assembly 8 GR8 3 Setting Arm Key 9 GR6 Bearing 0 G0306 G008 G0003 G387 G09 G00 GR003 Valve Cover Carriage Bolt, ⅜"6 x " Lock Nut, ⅜"6 Hex Head Cap Screw, ⅜"6 x ½" Flat Washer, ⅜" SAE Lock Washer, ⅜" Hex Nut, ⅜"6 A GA330 Piston Pump Complete W/8 Tooth Sprocket (Model NGP6055) Rev. 9/ P86

266 Liquid Fertilizer Piston Pump, NGP7055 M0330 (A335a/GR808) P87 Rev. 9/

267 M0330 Liquid Fertilizer Piston Pump, NGP7055 ITEM PART NO. QTY. DESCRIPTION GR80 G099 Flange Cover Assembly Hex Head Cap Screw, 5 6"8 x ⅞" GR803 Connecting Rod Assembly 3 GR80 G Spacer Assembly Hex Socket Head Set Screw, 5 6"8 x ⅜" GR3 Plug 5 GR53 Vent Plug 6 GR Woodruff Key 7 GR0 Eccentric Pin 8 GR Pin 9 GR0 Bearing 0 GR805 Setting Hub Assembly GR3 Stuffing Box Insert GR6 Sprocket, 8 Tooth 3 GR808 Adjustment Wrench GR806 Setting Pointer Assembly 5 GR796 Repair Kit, Includes: (6) Gaskets, (9) ORings, () Washers, () Retaining Ring, () Oil Seals, () Snap Ring, () Thrust Washer, () Rod Bushing, () Flange Plunger Packings, () Packing Springs, () Rod Vee Packing Sets 6 GR800 Discharge Valve Assembly 7 GR798 Suction Valve Assembly 8 GR8 3 Setting Arm Key 9 GR6 Bearing 0 G0306 G008 G0003 G387 G09 G00 Carriage Bolt, ⅜"6 x " Lock Nut, ⅜"6 Hex Head Cap Screw, ⅜"6 x ½" Flat Washer, ⅜" SAE Lock Washer, ⅜" Hex Nut, ⅜"6 GR0 Valve Cover, NPG7055 A GA335 Piston Pump Complete W/8 Tooth Sprocket (Model NGP7055) Rev. 9/ P88

268 Liquid Fertilizer Piston Pump Flow Divider M0330 (FRTZ0c) Model FD00 Flow Divider, Outlet ¾" NPT ITEM PART NO. QTY. DESCRIPTION GR53 Vent Plug GR5 GR5 Hex Socket Head Screw, ¼"0 x ¾", Stainless Steel Lock Washer, ¼", Stainless Steel 3 GR50 Cap GR5 Needle Assembly W/Seal Kit (Item 5) 5 GR55 Seal Kit, Includes: (3) ORings, () Seal, () Spring, () Stainless Steel Sleeve 6 GR535 Sleeve 7 GR533 Body ( Outlets) A GA893 Liquid Fertilizer Piston Pump Flow Divider Complete, Outlet (Model FD00) P89 Rev. 9/

269 This page left blank intentionally.

270 Rear Trailer Hitch M0330 (IP5) P9 Rev. 9/

271 M0330 Rear Trailer Hitch ITEM PART NO. QTY. DESCRIPTION GA75 G0055 G030 Front Hitch Hex Head Cap Screw, ⅝" x ¼" (Stop Bolt) Lock Washer, ⅝" GA908 Top Link W/Grease Fitting 3 GA758 Side Link W/Grease Fitting GD096 Pin, ¼" x 5½" 5 GD073 Compression Spring 6 GB03 Spring Seat 7 GD7907 Special Bolt 8 GD097 G0 G GD357 G060 0 GD70 G060 GA756 Rear Hitch GD8839 G060 Bushing, ¾" Hex Head Cap Screw, ⅞"9 x 3", Grade 8 Lock Washer, ⅞" Pin, ¼" x ¾" Cotter Pin, ¼" x " Pin, ¼" x 0¼" Cotter Pin, ¼" x " Pin, ¼" x 6¼" Cotter Pin, ¼" x " 3 GA677 Clevis W/Grease Fitting Rev. 9/ P9

272 Decals, Paint, and Miscellaneous M0330 Part No.: GD99 Description: SMV Sign Quantity: 9 Part No.: G70089 Description: Decal, Danger Quantity: Part No.: G70068 Description: Decal, Warning (Prior to 0 Production) Quantity: WARNING Uncontrolled machine movement can crush resulting in death, serious injury, or damage to property and equipment. Install safety lockup devices before working under or transporting this equipment. Part No.: G Description: Decal, Warning (0 Production and On) Quantity: P93 Rev. 9/

273 M0330 Decals, Paint, and Miscellaneous Part No.: G7007 Description: Decal, Danger Quantity: G7007 G7006 G70090 Part No.: G7006 Description: Decal, Warning Quantity: Part No.: G70090 Description: Decal, Warning Quantity: G70030 G70097 Part No.: G70030 Description: Decal, Warning Quantity: Part No.: G70097 Description: Decal, Warning Quantity: Rev. 9/ P9

274 Decals, Paint, and Miscellaneous M0330 G7007 or G Part No.: G7007 Description: Decal, Warning (Prior to 0 Production) Quantity: WARNING Uncontrolled machine movement can crush resulting in death, serious injury, or damage to property and equipment. Install safety lockup devices before working under or transporting this equipment. Part No.: G Description: Decal, Warning (0 Production and on) Quantity: G7000 Part No.: G7000 Description: Decal, Warning Quantity: G7003 G70059 Part No.: G70059 Description: Reflective Decal, Amber, ½" x 9", Rectangular Quantity: (one located on each side of hitch) Part No.: G7003 Description: Decal, Warning Quantity: P95 Rev. 9/

275 M0330 Decals, Paint, and Miscellaneous Part No.: G70083 Description: Decal, Warning (Prior to 0 Production) Quantity: (One Per Marker) G70083 or G WARNING Uncontrolled machine movement can crush resulting in death, serious injury, or damage to property and equipment. Install safety lockup devices before working under or transporting this equipment. Part No.: G Description: Decal, Warning (0 Production and on) Quantity: Part No.: G700 Description: Decal, Warning (Prior to 0 Production) Quantity: ( Per Row Marker) G700 or G WARNING CAUTION Row marker can lower at any time and could cause death or serious injury. Stay away from row markers! Install safety lockup device when not in use. Part No.: G Description: Decal, Warning (0 Production and on) Quantity: ( Per Row Marker) Rev. 9/ P96

276 Decals, Paint, and Miscellaneous M0330 Part No.: G70030 Description: Decal, Warning (Prior to 0 Production) Quantity: (One On Each Side Of Fan) CAUTION Fan can start at any time. Operating fan can blow debris and has a high noise level. Always wear eye and hearing protection when working around fan. Part No.: G70039 Description: Decal, Caution (0 Production and on) Quantity: (One On Each Side Of Fan) Part No.: G70066 Description: Decal, Danger (Prior to 0 Production) Quantity: (Located on each stair) WARNING Row 30" Falling from equipment can cause death or serious injury. Use three points of contact when working on equipment. Never ride on equipment! Part No.: G Description: Decal, Warning (0 Production and On) Quantity: (Located on each stair) 36 Row 0" P97 Rev. 9/

277 M0330 Decals, Paint, and Miscellaneous Part No.: G70059 Description: Reflective Decal, Amber, ½" x 9", Rectangular Quantity: (Per Row Unit Located On The Granular Chemical Hopper Panel Extension on Every Other Row Unit Beginning On The nd row unit in on the L.H. end of the Planter) (With Optional Granular Chemical) Part No.: G7006 Description: Reflective Decal, Amber, ¾" x 9", DieCut Quantity: (Per Row Unit Located On The Hopper Support on Every Other Row Unit Beginning on the nd row unit in on the L.H. end of the Planter) (Standard) Note: decals are used on Row 30" and 8 on 36 Row 0" Part No.: G70058 Description: Reflective Decal, Red, ½" x 9" Rectangular Quantity: (Located On The Two Center Row Units Rear Facing In Transport Position) Part No.: G70060 Description: Reflective Decal, Orange, ½" x 9" Rectangular Quantity: (Located On The Two Center Row Units Rear Facing In Transport Position) G70058 G70060 Standard G70058 G70060 With Optional Granular Chemical Rev. 9/ P98

278 Decals, Paint, and Miscellaneous M0330 Part No.: G70059 Description: Reflective Decal, Amber, ½" x 9", Rectangular Quantity: Optional Rear Trailer Hitch ( Row 30" only) Part No.: G70059 Description: Reflective Decal, Amber, ½" x 9", Rectangular Quantity: (Located On The Outside Row Unit On Each End Of The Planter ForwardFacing In Transport Position) G70059 Standard G70059 With Optional Granular Chemical P99 Rev. 9/

279 M0330 Decals, Paint, and Miscellaneous Part No.: G7005 Description: Decal, Warning Quantity: ( Per Row Unit Located On Underside Of Granular Chemical Hopper Lid) Part No.: G7007 Description: Decal, Warning (Prior to 0 Production) Quantity: (Two Per Center Lift Cylinder Lockup) WARNING Uncontrolled machine movement can crush resulting in death, serious injury, or damage to property and equipment. Install safety lockup devices before working under or transporting this equipment. Part No.: G Description: Decal, Warning (0 Production and on) Quantity: (Two Per Center Lift Cylinder Lockup) Part No.: G7009 Description: Decal, Warning Quantity: (Per Tire Ground Drive Tires) Rev. 9/ P00

280 Decals, Paint, and Miscellaneous M0330 Part No.: G Description: Decal, Warning Entrapment Quantity: (on each ASD Tank Lid) Part No.: G Description: Decal, Notice ASD Pressure Quantity: (on each ASD Tank Lid) Part No.: GD6 Description: Tie Strap, 8" Part No.: GD5 Description: Tie Strap, 7½" Part No.: GD7 Description: Tie Strap, ½" Part No.: GD98 Description: Tie Strap, 3" Part No.: G70095 Description: Decal, Spring Tension Release Quantity: Part No.: G7007 Description: Decal, Logo, ⅜" x ½" Quantity: (Per Row Unit) Part No.: G7005 Description: Decal, Logo, 3½" x 3⅝" (Hopper Panel Extension) Quantity: P0 Rev. 9/

281 M0330 Decals, Paint, and Miscellaneous Part No.: GD00570 Description: Hose Identification Sleeve, Red AA Part No.: GD00570 Description: Hose Identification Sleeve, Red BB Part No.: GD Description: Hose Identification Sleeve, Blue AA Part No.: GD00570 Description: Hose Identification Sleeve, Blue BB Part No.: GD Description: Hose Identification Sleeve, Yellow AA Part No.: GD Description: Hose Identification Sleeve, Yellow BB A A Part No.: GD0057 Description: Hose Identification Sleeve, Green PP Part No.: GD0057 Description: Hose Identification Sleeve, Green RR Part No.: GD0057 Description: Hose Identification Sleeve, Yellow PP Part No.: GD00575 Description: Hose Identification Sleeve, Yellow RR Part No.: GD00577 Description: Hose Identification Sleeve, Black PP Part No.: GD00578 Description: Hose Identification Sleeve, Black RR Part No.: GD00579 Description: Hose Identification Sleeve, Orange CD DIGITAL SENDING UNIT PDP Part No.: G7003 Description: Decal, Sending Unit Quantity: A DIGITAL SENDING UNIT EV Part No.: G70030 Description: Decal, Sending Unit Quantity: A Part No.: G7007 Description: Decal, Note Quantity: Rev. 9/ P0

282 Decals, Paint, and Miscellaneous M0330 Part No.: G700 Description: Decal, TwoSpeed Point Row Clutch Rate Reduction Part No.: G7009 Description: Decal, Point Row Clutch Rotation Part No.: G7003 Description: Decal, Bolt Torque Quantity: Part No.: G700 Description: Decal, Transmission, R.H. Quantity: Part No.: G700 Description: Decal, Transmission, L.H. Quantity: Part No.: G70053 Description: Decal, Information Quantity: Per BrushType Seed Meter Part No.: G70060 Description: Decal, Flow Control Part No.: G7003 Description: Decal, EdgeVac P03 Rev. 9/

283 M0330 Decals, Paint, and Miscellaneous NOTICE FAN MOTOR CASE DRAIN ALWAYS CONNECT THE FAN MOTOR CASE DRAIN HOSE TO THE TRACTOR ZERO PRESSURE RETURN. DO NOT CONNECT TO THE TRACTOR SCV OR MOTOR RETURN PORTS AS FAN HYDRAULIC MOTOR FAILURE WILL OCCUR NOTICE HYD MOTOR RETURN LINE ALWAYS CONNECT HYD MOTOR RETURN HOSE TO TRACTOR MOTOR RETURN PORT. DO NOT CONNECT TO THE TRACTOR SCV UNLESS THROUGH A MOTOR SPOOL. HYDRAULIC MOTOR FAILURE CAN OCCUR. Part No.: G70039 Description: Tag, Fan Motor Case Drain Part No.: G Description: Tag, Hydraulic Motor Return Line Part No.: G Description: Decal, Kinze Vision R EQUIPPED DRAIN MOISTURE FROM AIR TANK DAILY. DRAIN TANK COMPLETELY FOR STORAGE. Part No.: G70035 Description: Decal, Tank Drain Part No.: G700 Description: Decal, Oil Daily Part No.: G7006 Description: Decal, Grease Daily Part No.: G7000 Description: Decal, Grease Weekly Part No.: GR055 Description: Blue Paint, Aerosol Can Part No.: GR055MPP Description: Blue Paint, Twelve Aerosol Cans Rev. 9/ P0

284 Decals, Paint, and Miscellaneous M0330 Part No.: GR06 Description: Powdered Graphite, Pound Container Part No.: GR06MPP Description: Powdered Graphite, TwentyFour Pound Containers Part No.: GR570MPP Description: Talc Lubricant, Four 8 Pound Containers Part No.: GR88 Description: Talc Lubricant, 30 Pound Container Part No.: GR8MPP Description: Graphite Lubricant, Four 5 Pound Containers fi Part No.: G7005 Description: Decal, Kinze, 3 6" x 73 6" (Prior to 0 Production) Part No.: G7006 Description: Decal, Kinze 3700 Quantity: ( on each side of hitch) Part No.: G Description: Decal, Kinze 3700 Quantity: ( on each side of hitch) Part No.: GM0330 Description: Operator Manual, Part No.: GM0330 Description: Parts Manual, Part No.: GA5 Description: Operator s Manual Canister Quantity: Part No.: G356 Description: Hex Socket Flange Cap Screw, ¼"0 x ½" Quantity: 3 P05 Rev. 9/