ATE brake hose assemblies Highest mechanical stability under load, highest compressive strength and resistance
|
|
- Patience Rich
- 5 years ago
- Views:
Transcription
1 ATE brake hose assemblies Highest mechanical stability under load, highest compressive strength and resistance 1
2 ATE brake hose assemblies History Hydraulically actuated brakes, and consequently brake hose assemblies, too, similar to today's designs, have been available from Alfred Teves (ATE) since the 1920s. The first production car with a hydraulic brake from ATE was the 1927 ADLER Standard 6 and Favorit. This vehicle already featured brake hose assemblies on the front and rear axles. The demands on the "connecting hose" in the Adler were similar to those raised today, aside from the temperature level and certain other things. Owing to the growing demands, e.g., high temperatures, the testing of brake hose assemblies has acquired considerable scope. 2
3 Brake hose assemblies Definition Brake hose assemblies are used at the transitions to parts which are subject to heavy dynamic stresses steering knuckles or brake calipers, for instance. They ensure the proper transfer of brake fluid pressure to the brakes even under extreme conditions. Along with mechanical durability and pressure resistance, chemical resistance, e.g., to oil, fuels and other environmental influences, as well as good thermal resistance are essential requirements. To the high demands made on the system of brake lines, new ones have been added by ESP or TCS. The brake hose assembly plays an important role as damper and solves the problems raised by cramped installation positions. 3
4 Influences on brake hose assemblies All weather factors Operating pressure > 120 bar and brief peak overpressure of 160 bar (max. about 10 min.) Flying stones Mechanical stresses caused, e.g., by improper laying of the brake hose Damage like chafing Other influences Road salt Temperature loads caused by drier or heat radiator temperatures > 100 C during refinishing of a vehicle 4
5 Effects of defective brake hose assemblies Cracks owing to excessive mechanical stress or environmental influences If cracks are visible in the outer rubber layer of the brake hose, the car will fail to pass the next official inspection. In the initial stage (shortly after their formation) cracks have no negative influence on the operation of the brake hose, however. But if the cracks in the outer rubber layer go undiscovered over a lengthy period, environmental influences (e.g., moisture, cleaning agents or lubricants) may damage the pressure-resisting braiding beneath the rubber layer, and that can substantially impair proper functioning. The garage will have to examine the brake hoses carefully and replace them if necessary. 5
6 Present-day demands on efficient brake hoses Use over a large temperature range must be possible Low volumetric expansion of brake fluid High flexibility in the cold Negligible moisture absorption by inner and outer rubber layers High chemical resistance to the additives in high-grade brake fluids Great resistance to weathering and ozone These demands too go to define the characteristics of our ATE brake hose assemblies. 6
7 Design of ATE brake hose assemblies Outer rubber layer Double braiding Inner rubber layer The brake hose assembly structure features an inner tube, double-layer braiding as pressure resistor, and an outer rubber layer to protect the pressure-resisting braiding from external influences. Normally, at both ends of the hose threaded fittings are attached for making the connections with the brake pipe and caliper. But it is also possible to permanently connect the brake pipe with the brake hose assembly by means of a special connector (and to save effort for installation in the vehicle this way). 7
8 ATE brake hose assemblies - Types Mold-heated brake hose (vulcanized in a mold) TYPE 6/7 Freely heated brake hose (vulcanized in a water vapor atmosphere) TYPE 9 CR/EPDM EPDM RAYON PVA RAYON PVA CR/EPDM EPDM Rubber material CR EPDM = Chloroprene Rubber = Ethylene-propylene-diene copolymer Braiding Rayon PVA = Kunstseide = Polyvinyl alcohol 8
9 ATE brake hoses Characteristics of Type 9 Improved properties of material and product Vulcanized in a water vapor atmosphere Improved EPDM EPDM Double braided layer of PVAL yarn Service temperature range: -40 C to +120 C, briefly +160 C (max. about 10 min.) Very little elasticity under compressive stress, for well-modulated brake application EPDM PVAL PVAL Outstanding resistance to dynamic loading -40 C to +120 C, briefly +160 C (max. about 10 min.) Very good resistance to ozone Minimal volumetric expansion under pressure and minimal water absorption 9
10 Advantages & properties of ATE brake hose assemblies Branded product ATE utilizes the technology of OEM Continental. Use of the most up-to-date technology Mostly extruded connectors used, more than 70 braiding machines for producing the braid, autoclaves or vulcanizing presses and automatic surface control for the production of the inner and outer rubber layers Quality & safety guaranteed Test stands and laboratories are amply available for testing to customer specifications. Extraordinary quality standard owing to certification ATE brake hose assemblies comply with FMVSS106, and production is certified to ISO In addition, with the in-house ATE N standard they exceed the legal requirements. Hose marking The DOT symbol (DOT = US Department of Transportation) confirms the agreement of the hose with the most common motor vehicle safety regulations. High level of quality Continental uses only high-grade, long-lived materials to manufacture the brake hose assemblies. The surface protection of the connectors of the ATE brake hose assemblies is free of Cr-6, complying with the EU end-of-life-vehicle directive. 10
11 ATE brake hose assemblies Fittings / extras To the high demands made on the system of brake lines, new ones have been added by ESP or TCS. The brake hose assembly plays an important role as damper and solves the problems raised by cramped installation positions. To simplify fitting, preassembled brake hose assemblies are used to reduce the number of unchecked screwing operations and enabled simplified fastening in the vehicle. ATE brake hose assemblies are available in OE quality together with fittings of, e.g., the following types: Internal thread External thread Spacer Protective spring Floating attachment by means of clip-in rubber fasteners 11
12 ATE brake hose assemblies Notes on installation Fit brake hose assemblies in exact sizes and do not twist. Do not bend too short to fit. It's better to use an additional banjo union with banjo bolt. Lay brake hose assemblies so that chafing is impossible. Where there is danger of contact, make the brake hose assembly safe with a protective hose or by means of an additional hose clamp and tension spring. Should a brake hose assembly additionally be provided with a protective hose, this hose must neither be displaced nor removed. Do not lay near the exhaust system. Brake hose assemblies also must not come near the exhaust system when the vehicle springs deflect or the wheels are turned. If necessary, fit additional heat insulation. Do not lay in the immediate vicinity of lubrication points so as to avoid contact with excess oil or grease. Further details are contained in the instructions for use included with every ATE brake hose assembly! 12
Original ATE master brake cylinders OEM quality since the 1920s
Original ATE master brake cylinders OEM quality since the 1920s Expansion port TMC Central valve TMC Plunger TMC 1 Original ATE master brake cylinders Since the mid-1920s Continental has been supplying
More informationTips & Technology For Bosch business partners
Tips & Technology For Bosch business partners Current topics for successful workshops No. 73/2013 Gasoline injection Ignition cables technical information In gasoline engines, the high voltage required
More informationPTV TECHNICAL PRESCRIPTIONS. ELASTOMERIC SEALS: Part 1: Vulcanized Rubber FOR. Impartial institute for the monitoring of construction products
PTV 8681-1 TECHNICAL PRESCRIPTIONS TECHNICAL PRESCRIPTIONS FOR ELASTOMERIC SEALS: Part 1: Vulcanized Rubber COPRO vzw Version 1.0 dated 2017-10-17 Impartial institute for the monitoring of construction
More informationENERGY. TECWATER EMV-FC S1BC4N8-F 0,6/1 kv. Screened Cable for Water Application
ENERGY TECWATER EMV-FC S1BC4N8-F 0,6/1 kv Screened Cable for Water Application Technical Data Trademark Type designation Specification Application TECWATER EMV-FC S1BC4N8-F Design and tests according to
More informationSponge rubber products are manufactured in many different processes either by vulcanization in moulds or by extrusion.
Introduction Sponge rubber profiles from EPDM, CR, NBR, NR in various colours Sponge rubber is a cellular, softly elastic material made of caoutchouc. During vulcanization the material inflates forming
More informationSAFET Y PRODUCTS. TT-Series Safety Edge Product Manual
SAFET Y PRODUCTS TT-Series Safety Edge Product Manual 2TLC010046M0201_B ORIGINAL INSTRUCTION S Read and understand this document Please read and understand this document before using the products. Please
More informationfor Brake Hoses and Industrial Hoses Performance Rayon Reinforcement
for Brake Hoses and Industrial Hoses Performance Rayon Reinforcement Safety is key Among the many challenging demands placed by consumers on today s automobiles, safety is definitely a core topic. When
More informationSAFE USE AND HANDLING OF HOSES AND FLEXIBLE CONNECTIONS IN THE SOLVENTS INDUSTRY
GUIDANCE NOTE No. 60 SAFE USE AND HANDLING OF HOSES AND FLEXIBLE CONNECTIONS IN THE SOLVENTS INDUSTRY 1. Introduction The Solvents Industry Association has issued this Guidance Note because of the specific
More informationSUBJECT: EB e-stroke Disc Actuator & Harness Installation Guide
Actuator Mounting Instructions: 1. Remove Shipping Dust Cover from Actuator. 2. Reference Page 2: Ensure Mounting and Sealing Surfaces are Clean. 3. Reference Page 3: Lubricate Lever Arm Socket per Caliper
More informationMAXX TM 22T MECHANICAL SLIDING CALIPER DISC BRAKE INSTALLATION AND MAINTENANCE INSTRUCTIONS
MAXX TM 22T MECHANICAL SLIDING CALIPER DISC BRAKE INSTALLATION AND MAINTENANCE INSTRUCTIONS MAXX TM 22T Mechanical Sliding Caliper Disc Brake Installation and Maintenance Instructions Edition 1 This publication
More informationDRB Power Transmission Belts
DRB DRB power transmission belts, essential for transferring power of all automotive, industrial and agricultural machines all over the world, have been accepted by customers as a pronoun for quality and
More information20 HUBER+SUHNER RADOX SOLAR
All our cables fully comply with the European directives 76/769/EWG, 2003/11/EG, 2000/53/EG, 2003/53/EG and 2002/95/EG (RoHS) and the requirements of REACH Nr. EC1907/2006. 20 RADOX SOLAR cables RADOX
More informationPolymeric membrane for roof waterproofing. Uses Roof waterproofing membrane for exposed flat roofs: Loose laid and mechanically fastened
Roofing Product Data Sheet Edition 06.2013 Version no. 01 Sikaplan -20 G Polymeric membrane for roof waterproofing Product Description Sikaplan -20 G (thickness 2.0(- 5 % / + 10 %)mm) is a polyester reinforced
More informationG5 Stainless Steel Brakes Owners Manual
G5 Stainless Steel Brakes Owners Manual Important: Read all of this Stainless Steel Disc Brake Manual before starting installation or removal of any part on the disc brakes. TIE DOWN ENGINEERING 255 Villanova
More information2003 CR-V - A/T Shift Cable Replacement-Print Preview
Page 1 of 7 2003 CR-V - A/T Shift Cable Replacement 1. Raise the front of the vehicle, or lift the vehicle up, and make sure it is securely supported. 2. Remove the driver's dashboard lower cover, and
More informationMAIN SHAFT SUPPORT FOR WIND TURBINE WITH A FIXED AND FLOATING BEARING CONFIGURATION
Technical Paper MAIN SHAFT SUPPORT FOR WIND TURBINE WITH A FIXED AND FLOATING BEARING CONFIGURATION Tapered Double Inner Row Bearing Vs. Spherical Roller Bearing On The Fixed Position Laurentiu Ionescu,
More informationOverhead transmission lines Spacers
= SVENSKA KRAFTNÄT SWEDISH NATIONAL GRID UNIT, BUSINESS AREA AEL, Asset Management Lines OUR REFERENCE TR05-08E DATE 2016-06-09 CONSU12TATIONS TECHNICAL GUIDELINE REVISION 3 APPROVED Overhead transmission
More informationHYDRAULICS THE BASICS
HYDRAULICS THE BASICS WHAT IS HYDRAULICS? COMPONENTS OF A BASIC HYDRAULIC CIRCUIT HOSE ASSEMBLIES RUBBER HOSE STRUCTURE 6 WHAT IS HYDRAULICS? At its most basic level, hydraulics is the generation, control
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A136-1 1976-86 AMC 20 AXLES WITH WARN FULL FLOATING AXLE CONVERSION Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.
More informationSFI SPECIFICATION 35.2 EFFECTIVE: DECEMBER 29, 2014 *
SFI SPECIFICATION 35.2 EFFECTIVE: DECEMBER 29, 2014 * PRODUCT: Heavy Duty Stock Car Steel Wheels 1.0 GENERAL INFORMATION 1.1 This SFI Specification establishes uniform test procedures and minimum standards
More informationSarnafil TS E. Polymeric membrane for roof waterproofing. Product Description
Roofing Product Data Sheet Edition 06.2013 Version no. 01 Sarnafil TS 77-18 E Polymeric membrane for roof waterproofing Product Description Sarnafil TS 77-18 E8 E (thickness 1.8 mm) is a Polyester reinforced,
More informationENERGY. HYDROFIRM(T) EMV-FC S1BC4B-F 0,6/1 kv. Screened Cable for Drinking Water Application KTW/ACS
ENERGY HYDROFIRM(T) EMV-FC S1BC4B-F 0,6/1 kv Screened Cable for Drinking Water Application KTW/ACS Technical Data Trademark Type designation Specification Application HYDROFIRM(T) EMV-FC S1BC4B-F Design
More informationSKN_N0106AnnexJ_R2. Annex J - Specific requirements for PVT collector Certification. 1. Introduction and definition
Annex J - Specific requirements for PVT collector Certification 1. Introduction and definition PVT collectors (named hybrid collectors in ISO 9806) generate heat and electric power at the same time. They
More information1) Scheduled maintenance checks
1) Scheduled maintenance checks Definition This section lists the periodic inspections which must be carried out after a specified periods of operation. Intervals Periodic inspections are those which must
More information1. introduction 3 2. Wheel bearing special features 4 3. Wheel bearing units from an economical point of view 5
Motor chassis Service Technical BROCHuRE Wheel Bearing Repair Solutions for Light Commercial Vehicles CONTENT 1. introduction 3 2. Wheel bearing special features 4 3. Wheel bearing units from an economical
More informationIMPORTANT READ ME FIRST
IMPORTANT READ ME FIRST Thank you for purchasing your Kushlan Mixer. We hope that you will enjoy using it for many years to come. SHOULD YOU REQUIRE ANY SET-UP OR OPERATING ASSISTANCE WITH YOUR PRODUCT,
More informationTo determine if an A/C clutch should be returned for Warranty Consideration:
Warranty is a growing concern for all partners in the distribution of A/C Components. Because of the growing number of warranty questions, please study the following pictures to familiarize yourself with
More informationPoly-V-Belts February Description and Operation of the Poly-V- Belts. Removal of the Poly-V- Belts. Inspection of the Poly-V- Belts
1 02 13-18 SUBJECT DATE Poly-V-Belts February 2018 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change Description and Operation of the Poly-V- Belts DDC-SVC-MAN-0190
More informationAmendment 69 FR (20 December 2004) Section 5 Hydraulic brake hose, brake hose assemblies, and brake hose end fittings ESN270529
Vehicle Certification Agency 1 The Eastgate Office Centre Eastgate Road Bristol BS5 6XX United Kingdom Telephone: +44 (0) 117 951 5151 Fax: +44 (0) 117 952 4103 Email: enquiries@vca.gov.uk www.dft.gov.uk/vca/
More informationPURPOSE To show the correct procedures for the mounting and use of BREMBO braking systems for racing cars, with cast-iron brake discs.
PURPOSE To show the correct procedures for the mounting and use of BREMBO braking systems for racing cars, with cast-iron brake discs. RESERVOIR CHOICE OF THE RESERVOIR The capacity of the reservoir must
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A157 1991-2004 Dodge Dakota 2WD 1991-2002 Dodge Dakota 4WD 1998-2002 Dodge Durango Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for
More informationPUR c-track cables For highest requirements
2. C-track cables PUR c-track cables For highest requirements LÜTZE SUPERFLEX PLUS N PUR UL 300 V Machine and device construction, transport and conveyor technology Through full PUR jacket and TPE conductor
More informationPTV TECHNICAL PRESCRIPTIONS. ELASTOMERIC SEALS: Part 2: Thermoplastic Elastomers FOR
PTV 8681-2 TECHNICAL PRESCRIPTIONS TECHNICAL PRESCRIPTIONS FOR ELASTOMERIC SEALS: Part 2: Thermoplastic Elastomers COPRO vzw Version 1.0 dated 2017-10-20 Impartial institute for the monitoring of construction
More informationIDENTIFYING DISC COUPLING FAILURES COUPLING FUNDAMENTALS
IDENTIFYING DISC COUPLING FAILURES While couplings are designed for infinite life, they must be operated within their intended design limits in order to achieve optimal performance. Due to installation
More informationMATERIAL FOR FIBRE OPTIC LINES. General C-bracket HSU trunnion type, forged, for aluminium based OPGW conductors...
153 Contents General.................................................................................................. 154 C-bracket.................................................................................................
More informationIntroduction Elastomeric Bearing Expansion Joints Construction Profiles Projects
Table of contents Introduction Introduction Product Quality Elastomeric Bearing What Is Elastomeric Bearing? Types of Bearings & Usage Aspects and Architecture Constraining Movement Material Specifications
More informationAssembly and Maintenance Manual Type RSBW
Assembly and Maintenance Manual Type RSBW Hatschekstr. 36 69126 Heidelberg Germany Tel +49(0)6221 30470 Tel +49(0)6221 304731 info@stieber.de www.stieber.de Stieber Clutch Date of issue: 16/03/2017 GB
More informationModified polyolefin (-CR) or fluoropolymer (-CT) outer jacket
SELF-REGULATING HEATING CABLE For pipe freeze protection and flow maintenance Heating cable construction Tinned-copper braid Modified polyolefin (-CR) or fluoropolymer (-CT) outer jacket Modified polyolefin
More informationVulcatec your partner for hot vulcanized gaskets
Vulcatec your partner for hot vulcanized gaskets About us Vulcatec has been delivering know-how and high quality products for over 30 years. As a specialist in the field of made-to-measured gaskets, we
More informationATS metal clutch (twin / triple) instruction manual for Nissan 350Z w/ HR motor 12 pages
ATS metal clutch (twin / triple) instruction manual for Nissan 350Z w/ HR motor 12 pages This instruction is provided by Performance Partners Intl 1 ATS Clutch operating instructions Thank you very much
More informationSummer Inspections, Maintenance And Repair
Summer 2014 Summer Inspections, Maintenance And Repair The difficult winter is in the rear view mirror, you have taken a quick breath in the spring and it is time now to take a real rest. Right? Not so
More informationTECHNICAL BULLETIN Coolant Types and their Purpose Issue: April 2015
TECHNICAL BULLETIN Coolant Types and their Purpose Issue: April 2015 WHAT IS COOLANT? Automotive coolant is a solution mixed with water to improve heat transfer and control the operating temperature of
More informationISO 3996 INTERNATIONAL STANDARD. Road vehicles - Brake hose assemblies for hydraulic braking Systems used with non-petroleum-base brake fluid
INTERNATIONAL STANDARD ISO 3996 Third edition 1995-02-01 Road vehicles - Brake hose assemblies for hydraulic braking Systems used with non-petroleum-base brake fluid Vkhicules routiers - Flexibles pour
More informationCougar DC Truck Vibrators
Cougar DC Truck Vibrators Go to Cougar DC Truck Vibrators web page Operator s Manual M3952 Important MARTIN ENGINEERING HEREBY DISCLAIMS ANY LIABILITY FOR: DAMAGE DUE TO CONTAMINATION OF THE MATERIAL;
More informationAutomotive Vibration Control Technology
TrelleborgVibracoustic (Ed) Automotive Vibration Control Technology Fundamentals, Materials, Construction, Simulation, and Applications Vogel Business Media isoprene natural isobuteneisoprene styrenebutadiene
More informationSIDE-WIND, A-FRAME TRAILER JACK. Model Due to continuing improvements, actual product may differ slightly from the product described herein.
SIDE-WIND, A-FRAME TRAILER JACK Model 95157 Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd.,
More informationRailway Engineering: Track and Train Interaction COURSE SYLLABUS
COURSE SYLLABUS Week 1: Vehicle-Track Interaction When a railway vehicle passes over a track, the interaction between the two yields forces on both vehicle and track. What is the nature of these forces,
More informationFAG Wheel Bearing Repair Solution for Light Commercial Vehicles
FAG Wheel Bearing Repair Solution for Light Commercial Vehicles Mercedes-Benz Sprinter, Viano, Vito and Volkswagen Crafter Front Axle The content of this brochure shall not be legally binding and is for
More informationOperating Instruction and. Parts Manual for
Operating Instruction and 350DD Epoxy Parts Manual for WARNING DO NOT ATTEMPT TO START OR OPERATE THE MACHINE UNTIL ALL THE INSTRUCTIONS HAVE BEEN READ AND UNDERSTOOD BY THE OPERATOR. FAILURE TO DO SO
More informationHEBEI QIANLI RUBBER PRODUCTS CO., LTD. AIR HOSE. Air hose for air tools or compressor equipment. Technical Data
AIR HOSE Air hose for air tools or compressor equipment Technical Data Company Profile is a technical company, which focus on researching, developing, manufacturing and exporting rubber hose and related
More informationPumps and pumping units SL i & Micro C
INSTRUCTIONS 1071 e Section Effective October 2016 Replaces April 2016 Original instructions Additional instructions for ATEX certified equipment Pumps and pumping units SL i & Micro C Дистрибутор: България,
More informationBuffer elements 1109
Buffer elements 1109 Technical information for rubber-metal buffers Our rubber-metal buffers are simple and cost-efficient standard units for elastic mounting. They are ideally suited for compressive and
More informationTHE INFLUENCE OF VISIBILITY CONDITIONS IN HORIZONTAL ROAD CURVES ON THE EFFICIENCY OF NOISE PROTECTION BARRIERS
DOI: 10.1515/rjti-2015-0016 ROMANIAN JOURNAL THE INFLUENCE OF VISIBILITY CONDITIONS IN HORIZONTAL ROAD CURVES ON THE EFFICIENCY OF NOISE PROTECTION BARRIERS Tamara Džambas, Assistant, MCE, University of
More information2015 TYRE RANGE 2016
TYRE RANGE 2015 2016 TABLE OF CONTENTS PRODUCT OVERVIEW D500S... 4 D600D... 5 D400T... 6 GENERAL INFORMATION Tyre sidewall information.... 8 Variation in load carrying capacity with speed and inflation
More informationNEW: RAUFILAM -E COLOUR ALWAYS THE RIGHT CHOICE. Industrial hoses, with and without fabric lining
NEW: RAUFILAM -E COLOUR ALWAYS THE RIGHT CHOICE Industrial hoses, with and without fabric lining PRESSURE-RESISTANT HOSES IN FOOD-GRADE QUALITY RAUFILAM -E fibre reinforced, design and KTW approved Proven
More information1250 LB. CAPACITY MECHANICAL WHEEL DOLLY
1250 LB. CAPACITY MECHANICAL WHEEL DOLLY 67287 SET-UP AND OPERATING INSTRUCTIONS Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result
More informationPart 7 DO IT YOURSELF MAINTENANCE
Part 7 DO IT YOURSELF MAINTENANCE Chapter 7 2 Engine and Chassis Checking the engine oil level Checking the engine coolant level Checking brake fluid Checking power steering fluid Checking tire pressure
More informationPLEASE READ BEFORE CALLING OR RETURNING PRODUCT. EXTREMELY IMPORTANT!!!
Thank you for your purchase of WeaponX Smart Direct Fire Ignition Coil System for your vehicle. The following are the instruction manuals for your ignition system kit. Please read carefully and enjoy your
More informationLoad Cell for Manually Operated Presses Model 8451
w Technical Product Information Load Cell for Manually Operated Presses 1. Introduction... 2 2. Preparing for use... 2 2.1 Unpacking... 2 2.2 Using the instrument for the first time... 2 2.3 Grounding
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR CONVERSION KIT A111-2 (FORD 8" & 9" SMALL BEARING) & REAR CONVERSION KIT A111-3 (FORD 9 TORINO) Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking
More informationShock Absorbers What is Ride Control Vehicle Dynamics Suspension System Shock Absorbers Struts Terminology
Home Tech Support Shock Absorbers Shock Absorbers What is Ride Control Vehicle Dynamics Suspension System Shock Absorbers Struts Terminology A BRIEF HISTORY These first shock absorbers were simply two
More informationMechanism and Countermeasures for Abnormal Noise Produced by Idler Pulley Bearings under Low Temperature Conditions
Mechanism and Countermeasures for Abnormal Noise Produced by Idler Pulley Bearings under Low Temperature Conditions M. UEDA Idler bearings are used for automobile engine accessories. This bearing sometimes
More informationIndustrial flue gas probes. Instruction manual
Industrial flue gas probes Instruction manual 2 1 Contents 1 Contents 1 Contents... 3 2 Safety and the environment... 4 2.1. About this document... 4 2.2. Ensure safety... 4 2.3. Protecting the environment...
More informationStandard Elastomeric Bearings
Standard Elastomeric s Elastic support of structural members subject to static loading Scope and dimensioning guidelines planmäßig elastisch lagern Standard Elastomeric s type bi-trapez Permissible compressive
More informationDIN EN : (E)
DIN EN 13480-3:2017-12 (E) Metallic industrial piping - Part 3: Design and calculation Contents Page European foreword... 10 1 Scope... 12 2 Normative references... 12 3 Terms, definitions, symbols and
More informationAtlas ESR and ESR + Equivalent Series Resistance and Capacitance Meter. Model ESR60/ESR70. Designed and manufactured with pride in the UK.
GB60/70-9 Atlas ESR and ESR + Equivalent Series Resistance and Capacitance Meter Model ESR60/ESR70 Designed and manufactured with pride in the UK User Guide Peak Electronic Design Limited 2004/2016 In
More informationZ32 Solid Rear Subframe Bushing Installation
Z32 Solid Rear Subframe Bushing Installation Thank you for purchasing a set of Sonic Motorsport (NZ) designed and 300 Degree produced solid subframe bushings! Over time the OEM subframe bushings will fail.
More informationRELIABILITY IMPROVEMENT OF ACCESSORY GEARBOX BEVEL DRIVES Kozharinov Egor* *CIAM
RELIABILITY IMPROVEMENT OF ACCESSORY GEARBOX BEVEL DRIVES Kozharinov Egor* *CIAM egor@ciam.ru Keywords: Bevel gears, accessory drives, resonance oscillations, Coulomb friction damping Abstract Bevel gear
More informationSTART HERE GRILLE REMOVAL. 1) Turn off engine and chalk tires with stop block. Open Hood. 1. Disconnect negative battery terminal.
GRILLE REMOVAL & Grille Installation Guide Parts included (1) LASER TORCH - Main Part #7315711 (1) LASER TORCH STEALTH - Main Part #7315711-BR (1) 30 LED Light Bar (1) Power Cable Wiring Harness Hardware
More informationAPCO CRF-100A RUBBER FLAPPER SWING CHECK VALVES
APCO CRF-100A RUBBER FLAPPER SWING CHECK VALVES Instruction D12043 June 2016 DeZURIK Instructions These instructions provide installation, operation and maintenance information for APCO CRF-100A Rubber
More informationAUTOMOTIVE HOSE G611 FUEL LINE. Tube: Smooth, black, oil and gasoline resistant nitrile rubber.
& Truck HOSE 8 AUTOMOTIVE HOSE Gasoline & diesel hose for fuel tanks & filler necks can be found in Marine Section Fuel Line hose is specially compounded to withstand the high under-the-hood temperatures
More informationKeystone Butterfly valves ParaSeal Installation and maintenance instructions
Before installation these instructions must be fully read and understood Please read these instructions carefully Hazard potentials: disregarding of instructions improper use of product insufficiently
More informationSUSPENSION 04 CLAMPS
SUSPENSION CLAMPS 04 4 SUSPENSION CLAMPS 57 Contents General... 58 Suspension clamp trunnion type, forged,... 63 Suspension clamp trunnion type, forged, with bigger angle of deflection, for aluminium based
More informationh Technical Product Data CC Pressure Pipe Systems
h Technical Product Data CC Pressure Pipe Systems Amiblu Holding GmbH All rights reserved. Publication: 09/2018 This version replaces all previous versions. For all current data please visit our website
More informationMonarch #5032. Product W L T W L T
AUTOMOTIVE Monarch #5032 UL94 HF-1 listed for flame UL50E (periodic and continuous compression), UL508 and UL48 listed for gaskets and seals (recent upgrade) Widely used general purpose EPDM / CR / SBR
More informationPE-HDXc pipes (physically cross-linked polyethylene pipes)
pipes (physically cross-linked polyethylene pipes) Applications: Domestic drinking water installations, radiator connections and surface regulation Special properties high chemical resistance (according
More informationViper Parts Catalog. January 2011 Innovative Peripheral Solutions (IPS),
Viper Parts Catalog Innovative Peripheral Solutions (IPS) has been a manufacturer of parts for the Dodge Viper since 1997, and has produced many products for Vipers including brake systems, cosmetic parts,
More informationENERGY. Solar Cables
ENERGY Solar Cables Contents TECSUN(PV) PV1-F Cables for Photovoltaics 3 Technical Data 4 Design Features 6 Selection and Ordering Data 6 TECSUN DUO (PV) Cables for Photovoltaics 7 Technical Data 8 Design
More informationElastomer Products for Energy Control
TUBUS Bumpers Elastomer Products for Energy Control Outperform Rubber, Urethane and Coiled Steel ACE Controls Inc. Innovation in Deceleration and Motion Control ISO 9001 Certified 01/09(R) Revised 12/10
More information1940 Hudson SERVICING THE FRONT SUSPENSION SYSTEM
1940 Hudson SERVICING THE FRONT SUSPENSION SYSTEM Source of this material is from 1940 Series, Issue 3, November-December Hudson Service Magazine SERVICING THE FRONT SUSPENSION SYSTEM No set rule can be
More informationAssembly and Maintenance Manual Type ASNU
Assembly and Maintenance Manual Type ASNU Hatschekstr.36 69126 Heidelberg Germany Tel +49(0)6221 30470 Fax +49(0)6221 304731 info@stieber.de www.stieber.de Date of issue: 30.05.2018 GB Revision: 0 U:\EngUsers\!ProduktDoku\1AAA_Einbauerklaerung_Wartungsanleitung_Konformitaetserklaerung\1AAA_Wartungsanleitungen\Orginal_Worddatei\_ASNU.docx
More informationMonarch. Monarch #5013. General Info
AUTOMOTIVE Monarch #5013 UL94 HF-1 and HBF listed for flame UL50E (periodic and continuous compression), UL508 and UL48 listed for gaskets and seals (recent upgrade) Widely used general purpose blend ASTM
More informationInstallation Procedures
For the precision ball and roller bearings supplied by MRC Bearings, skill and cleanliness while handling, mounting and dismounting are necessary to ensure satisfactory bearing performance. As precision
More informationJames Barone Racing Aftermarket Parts and Accessories
Page1 James Barone Racing Aftermarket Parts and Accessories What you will need: 2014+ Mazda 3, 6 and CX-5 Adjustable Rear Camber Arm Installation Instructions. Jack, jack stands Socket wrench Socket wrench
More information79-93 MUSTANG 2 PISTON FLOATER FRONT BRAKE KIT INSTRUCTIONS
79-93 MUSTANG 2 PISTON FLOATER FRONT BRAKE KIT INSTRUCTIONS Preparing the Spindle FOR ANY QUESTIONS PLEASE CALL US @(727) 347-9915 M-F 8:00 AM -8:00 PM EST YOU WILL NEED TO MODIFY YOUR SPINDLE. Note: Some
More information6 Options and Accessories
Torque arm Options and Accessories.1 Torque arm A torque arm is available to support the reaction torque of hollow shaft gear units in the shaft-mounted version. The torque arm can bear tensile stress
More informationSTART HERE GRILLE REMOVAL. 1) Turn off engine and chalk tires with stop block. Open Hood. 1. Disconnect negative battery terminal.
Parts included (1) X-Metal - Main Part #6715791 (1) Stealth X-Metal - Main Part #6715791-BR (1) Laser X-Metal - Main Part #7715891 (1) Laser Stealth X-Metal - Main Part #7715891-BR (1) Universal X-Metal
More informationPerformance-Gewindefahrwerke Performance Coilover Kits
Performance-Gewindefahrwerke Performance Coilover Kits Kit-Nr.: 84 1500 118 454 Für folgende Fahrzeuge / For the following vehicles: BMW 1er-Reihe (E81, E82, E87) BMW 3er-Reihe (E90, E91, E92, E93) Inhalt:
More informationPower Transmission. Installation and Operating Instructions for Integrated Freewheels FXRV and FXRT. E e.
Power Transmission Installation and Operating Instructions for Schaberweg 30-34 Telephone +49 6172 275-0 61348 Bad Homburg Telefax +49 6172 275-275 Germany www.ringspann.com mailbox@ringspann.com Issue:
More informationBM kv Digital Insulation Tester USER MANUAL
M BM5200 5 kv Digital Insulation Tester USER MANUAL CONTENTS Safety warnings...3 Symbols used on instrument...4 Cleaning...4 General description...5 Insulation resistance test modes...5 Automatic discharge...5
More informationAssembly Instructions
Assembly Instructions Revision 4: 2016 TABLE OF CONTENTS Important Information 5 Warranty 5 Limit of Liability 5 For Your Records 5 Operation 5 Maintenance 6 When Your Shipment Arrives 6 Tools & Personnel
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A158 1994-97 Dodge Ram 1500 (2WD & 4WD) and REAR DISC BRAKE CONVERSION KIT A158-1 1998-01 Dodge Ram 1500 (2WD & 4WD) Thank you for choosing STAINLESS
More informationJUMO plastosens T. Temperature probes made of high-performance plastic
JUMO plastosens T Temperature probes made of high-performance plastic JUMO plastosens T01 Voltage-resistant plastic temperature probe In dry or cast resin transformers the use of temperature probes made
More informationSince 1995, Power Stop has earned an outstanding reputation for providing high quality brake parts at a great value. Our products are specially formulated for the demanding auto enthusiast. We are the
More informationAEROFLEX. Closed Cell Elastomeric Thermal Insulation (made from E.P.D.M. - Ethylene Propylene Diene Monomer)
Closed Cell Elastomeric Thermal Insulation (made from E.P.D.M. - Ethylene Propylene Diene Monomer) Aeroflex Tube and Sheet Insulation is a flexible, closed cell and lightweight elastomeric material designed
More informationProduct information. Water cooled high current cables preferably for electric arc- and ladle furnaces
Flexible connectors Solderless terminals Contact-systems Product information Water cooled high current cables preferably for electric arc- and ladle furnaces Water cooled high current cables 2014 Paul
More informationDatasheets - General Purpose Elastomers
Datasheets - General Purpose Elastomers Natural Rubber (NR) Market introduction 1840 Price indication, volume index compound 1,0 Service temperature, min C -50 Service temperature, max C +80 Mechanical
More information2014 Private Use Application Guide Issue Century Series
2014 Private Use Application Guide Issue 1 5-8-14 Century Series Century Series Features The Century Series is an extremely versatile lift, designed to fit a variety of personal-use applications. The unique
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS COMP. R AND COMP. S QUICK CHANGE KITS A200, A200-1 Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read and carefully
More informationTable of Contents. Safety... 2 Specifications... 3 Setup Parts List and Diagram Warranty Operation Maintenance
Table of Contents Safety Setup Operation Maintenance Safety... 2 Specifications... 3 Setup... 4 Operation... 5 WARNING SYMBOLS AND DEFINITIONS Maintenance... 9 Parts List and Diagram... 10 Warranty...
More information