Pre-made Self Regulating Trace Heating Cable Kit with Built-in Thermostat & Cold Lead INSTALLATION AND TECHNICAL MANUAL
|
|
|
- Emma Benson
- 5 years ago
- Views:
Transcription
1 Pre-made Self Regulating Trace Heating Cable Kit with Built-in Thermostat & Cold Lead INSTALLATION AND TECHNICAL MANUAL
2 Technical Data Power supply 230 VAC Power C) 12 W/m Min. fuse (type C) 10 A Max. exposure temperature (energised) 65 C Max. exposure temperature (de-energised) 85 C Outer jacket Polyolefin Cold lead length 2m Min. bend radius 25mm IP rating IP 67 Min. installation temperature -30 C Min. switch on temperature -45 C 2
3 Installation Important Notes The existence of the trace heating cable has to be made evident by on-site warning notices, e.g. in the fuse box. Furthermore they have to be part of the electrical documentation alongside the installation. Please ensure that during normal operation the temperature of the pipes does not exceed 60 C. Please avoid sharp edges as well as high drag forces when installing and drawing the heating tapes. Cover the trace heating cable with an aluminium adhesive tape when installing onto plastic pipes and plastic components. You must not go below the minimum bending radius. It is recommended to have the installation done by a qualified electrician. The installation must be fitted in accordance with the latest local & international regulations and standards. Frost protection for pipes up to 54mm diameter. Important Step Follow our simple step by step instructions to install your frost protection trace heating system. 1 1 Roll out the trace heating cable. Avoid bending the heatng cable beyond the minimum bend radius. 2 2 Cable Install the trace heating cable (depending on the thickness of the pipe and the required heating power) alongside the pipe in single or multiple runs, and fix it to the pipe at approximately 300mm intervals using the cable ties provided. 1 3 Aluminium adhesive tape For plastic pipe and plastic components the trace heating cable must be wrapped with an 2 aluminium adhesive tape. 4 Lagging Cable After installation of the trace heating cable, the pipes must be insulated with a minimum of 20mm lagging (Armaflex/PU Foam/Mineral Wool). Recommended Installation Positions 3 4 Install the trace heating cable in the recommended positions for single, double and triple runs as required (see illustrations, right). 3 4 Aluminium adhesive tape Cable Single Double Triple Lagging 3
4 Test Report Purchase Date... Address Postcode... Installation Date... Signature Starting Up Date... Signature Test Protocol Record the insulation resistances of your installation in the format below. Before Installation After Installation Start Up MΩ MΩ MΩ 4
5 Heating Power Selection Power Output Curve The characteristic feature of the heating tape used in trace heating cable is that they are self-limiting. This means that the heating cable emits a high heating power with low ambient temperatures and a low heating power with high ambient temperatures. This means an overheating of the heating tape is eliminated. The trace heating cable has a standard power of 12W/m. The standard power is measured at +10 C. Power Output(W/m) Workpiece temperature ( C) 5
6 Heating Power Selection Heatloss Tables Heat losses occur if the ambient temperature around the pipe is lower than the temperature of the pipe. Though a permanent heat transmission takes place (from warm to cold) which may lead to the freezing of the pipe in the worst case. The trace heating cable is suitable for keeping insulated pipes frost-free at an ambient temperature of lower than -30 C. The tables on the following page are intended to make it easier for you to choose the right insulation thickness. The heating losses shown in these tables were established for an ambient temperature of -20 C. Please install the heating cables only alongside the pipe. In case the power of the heating cable is not sufficient to offset the heat loss, we kindly ask you to increase the number of insulation layers or thickness. Please pay attention to the fact that the shown values are approximate values only and are intended as a selection help only. The insulation values are average values only which may differ with different suppliers/manufacturers. The measuring unit for the heat loss is W/m. Armaflex Insulation (0.042W/m K) Insulation Thickness Pipe Ø 5mm 10mm 15mm 20mm 30mm 6mm 8 W/m 6 W/m 5 W/m 4 W/m 3 W/m 8mm 10 W/m 6 W/m 5 W/m 4 W/m 4 W/m 10mm 11 W/m 7 W/m 6 W/m 5 W/m 4 W/m 15mm 15 W/m 8 W/m 7 W/m 6 W/m 5 W/m 22mm 21 W/m 10 W/m 8 W/m 7 W/m 5 W/m 28mm 26 W/m 12 W/m 9 W/m 8 W/m 6 W/m 35mm 32 W/m 14 W/m 10 W/m 9 W/m 7 W/m 42mm 37 W/m 16 W/m 12 W/m 10 W/m 7 W/m 54mm 47 W/m 19 W/m 14 W/m 11 W/m 8 W/m 6
7 Heating Power Selection PU Foam Insulation (0.025W/m K) Insulation Thickness Pipe Ø 5mm 10mm 15mm 20mm 30mm 6mm 5 W/m 4 W/m 3 W/m 3 W/m 2 W/m 8mm 6 W/m 4 W/m 3 W/m 3 W/m 2 W/m 10mm 7 W/m 5 W/m 4 W/m 3 W/m 3 W/m 15mm 9 W/m 6 W/m 4 W/m 4 W/m 3 W/m 22mm 13 W/m 7 W/m 5 W/m 4 W/m 4 W/m 28mm 15 W/m 8 W/m 6 W/m 5 W/m 4 W/m 35mm 19 W/m 10 W/m 7 W/m 6 W/m 4 W/m 42mm 22 W/m 11 W/m 8 W/m 6 W/m 5 W/m 54mm 28 W/m 13 W/m 9 W/m 8 W/m 6 W/m Mineralwool Insulation (0.035W/m K) Insulation Thickness Pipe Ø 5mm 10mm 15mm 20mm 30mm 6mm 7 W/m 4 W/m 4 W/m 3 W/m 3 W/m 8mm 8 W/m 5 W/m 4 W/m 4 W/m 3 W/m 10mm 10 W/m 6 W/m 5 W/m 4 W/m 3 W/m 15mm 13 W/m 8 W/m 6 W/m 5 W/m 4 W/m 22mm 18 W/m 10 W/m 8 W/m 6 W/m 5 W/m 28mm 22 W/m 12 W/m 9 W/m 7 W/m 6 W/m 35mm 26 W/m 15 W/m 11 W/m 9 W/m 7 W/m 42mm 31 W/m 17 W/m 12 W/m 10 W/m 7 W/m 54mm 39 W/m 21 W/m 15 W/m 12 W/m 9 W/m 7
8
Pre-made Self Regulating Trace Heating Cable Kit with Built-in Thermostat & Cold Lead INSTALLATION AND TECHNICAL MANUAL
Pre-made Self Regulating Trace Heating Cable Kit with Built-in Thermostat & Cold Lead INSTALLATION AND TECHNICAL MANUAL Technical Data Power supply 230 VAC Power (@+10 C) 12 W/m Min. fuse (type C) 10 A
FREEZSTOP MICRO SYSTEM. Freeze Protection of Pipework
FREEZSTOP MICRO SYSTEM Freeze Protection of Pipework Prevent Burst or Blocked Pipes The Problem Thermal insulation alone will not prevent freezing of pipes. For example, a 3/4 pipe having 25mm thick insulation
The advantages of the pipe tracing systems are: Sensor. Insulation Heating cable Aluminium tape. Fig. 1 Fig. 2
28 3 Pipe tracing 3.1 General information DEVI s pipe tracing systems consist of deviflex heating cables, devireg thermostats and installation accessories. The devireg thermostats with sensors ensure that
HTSB system System overview
HTSB system System overview Easy planning of heating circuits Simple installation on site Wide operating temperature range The BARTEC HTSB heating system covers a wide range of applications in trace heating.
Frost protection for pipes. 16 Technical handbook. Thermostat with line or ambient temperature sensor
Frozen pipes can be a costly problem. When pipes are exposed to subzero temperatures they can burst, leading to considerable damage and disruption. The Raychem frost protection system provides an efficient
Frost protection for pipes. 16 Technical handbook. Thermostat with line or ambient temperature sensor
Frozen pipes can be a costly problem. When pipes are exposed to subzero temperatures they can burst, leading to considerable damage and disruption. The Raychem frost protection system provides an efficient
Self-regulating frost protection system for pipes
AT-TS-13 60 30 90 0 C 120 Self-regulating frost protection system for pipes eliability: protects your pipes from frost damage Maintenance-free Efficient energy use FS-A-2X: 10 W/m at 5 C FS-B-2X: 26 W/m
DOMESTIC USE. Anti-freeze for Piping CONSTANT POWER. Anti-freeze for Ramps. Stop Ice Constant power anti-freeze kit complete with thermostat and plug
DOMESTIC USE Anti-freeze for Piping CONSTANT POWER page 190 Stop Ice Constant power anti-freeze kit complete with thermostat and plug Linus Self-adhesive thermal insulating tape Stop Ice Plus Constant
Ecoflex potable PEX plus pre-insulated pipe system Installation guide
Ecoflex potable PEX plus pre-insulated pipe system Installation guide Ecoflex potable PEX plus pre-insulated pipe system installation guide l 1 Uponor Ecoflex potable PEX plus pre-insulated pipe system
Heating Cable. Cut to Length in Field. Description
Self-Regulating Freeze Protection D E C B A Self-Regulating, Energy Efficient Designed for Freeze Protection Max. Exposure Temp. 185 F Temperature Cost Effective for Commercial Construction Freeze Protection
FREEZSTOP MICRO SYSTEM
FREEZSTOP MICRO SYSTEM Freeze Protection of Pipework Prevent Burst or Blocked Pipes The Problem Thermal insulation alone will not prevent freezing of pipes. For example, a 25mm diameter water pipe at +5
120/240 Volts 3 Watt Floor Heating Cable System
WA-3CWC 120/240 Volts 3 Watt Floor Heating Cable System Warm Cable floor heating system combines the highest comfort levels with maximum energy efficiency. It is a proven technology that is safe, reliable
Self-regulating heating cables with a non-heating service cable
N144/R02(22.08.18) Self-regulating heating cables with a non-heating service cable ELSR-M-15-2-BO ELSR-N--2-AO ELSR-N-30-2-AO GENERAL CONDITIONS The connector which connects the cold end and the heating
Nuheat WEATHER-READY HEAT TRACE PIPE FREEZE PROTECTION SYSTEM. Self-Regulating Heating Cable Installation Guide. UV Resistant Polyolefin Outer Jacket
Nuheat WEATHER-READY HEAT TRACE PIPE FREEZE PROTECTION SYSTEM Self-Regulating Heating Cable Installation Guide Tinned Copper Braid UV Resistant Polyolefin Outer Jacket 16 AWG Bus Wire Polyolefin Inner
Kompensator External Low Voltage Heating Cable System
External Low Voltage Heating Cable System LOW VOLTAGE Installation Instructions General Information Kit Contents Qty Description 1 heating cable at pre-determined length Table of Contents General Information........................
Segurança. Segurança. PSB Heating System Cold applied connection technology. Compulsório. Compulsório. Operation Manual and Installation Instructions
Segurança TC RU C-DE.ГБ06.B.00230 OCP 0004 Compulsório INMETRO Operation Manual and Installation Instructions Segurança PSB Heating System Cold applied connection technology Compulsório Type 27-1680-...0/...
PIPE FREEZE PROTECTION AND FLOW MAINTENANCE XL-TRACE SYSTEM
PIPE FREEZE PROTECTION AND FLOW MAINTENANCE XL-TRACE SYSTEM This step-by-step design guide provides the tools necessary to design a Raychem XL-Trace pipe freeze protection or flow maintenance system. For
frost protection Constant wattage heating cables Self-regulating heating cables Temperature controllers
frost protection Constant wattage heating cables Self-regulating heating cables Temperature controllers Heating systems protect pipes, valves, actuators and other elements vulnerable to harmful influence
STRAIGHT PERFORATED TRAY
STRAIGHT PERFORATED TRAY RETURNED EDGE TYPE RETURNED FLANGE TYPE NOTE: Other sizes are available upon request WIDTH (W) HEIGHT (H) 50 15 15 150 15 15 15 400 15 500 15 600 15 STRAIGHT CABLE TRAY STANDARD
Instruction Manual. for Heating Cables and Cold Leads Type and Catalogue no and Hemstedt GmbH.
Instruction Manual for Heating Cables and Cold Leads Type 68994- and 68997- Catalogue no. 68994- and 68997- Hemstedt GmbH Schleicherweg 19 D-74336 Brackenheim-Botenheim Phone +49 (7135) 9898-0 Fax +49
HEATING TECHNOLOGY HEATING TAPES/HEATING CABLE SYSTEMS CLOSED- AND OPEN-LOOP CONTROL SYSTEMS HEATERS WATER LEAKAGE DETECTION SYSTEMS
HEATING TECHNOLOGY HEATING TECHNOLOGY HEATING TAPES/HEATING CABLE SYSTEMS 1 CLOSED- AND OPEN-LOOP CONTROL SYSTEMS 2 HEATERS 3 WATER LEAKAGE DETECTION SYSTEMS 4 PROJECT PLANNING INFORMATION 5 CONTENT
Modified polyolefin (-CR) or fluoropolymer (-CT) outer jacket
SELF-REGULATING HEATING CABLE For pipe freeze protection and flow maintenance Heating cable construction Tinned-copper braid Modified polyolefin (-CR) or fluoropolymer (-CT) outer jacket Modified polyolefin
SLIMFLEX LED Tape Lighting
1 SLIMFLEX LED Tape Lighting Installation Guide BEFORE YOU BEGIN, READ INSTALLATION INSTRUCTIONS THOROUGHLY Install in accordance with the National Electric Code and local regulations This product is intended
EHeating Cables. ELEKTRA FreezeTec. Application. with integrated thermostat
ELEKTRA FreezeTec EHeating Cables with integrated thermostat Application ELEKTRA FreezeTec is intended for protection of pipes and valves susceptible to damage caused by low temperatures. The system may
XL-Trace System. Installation and Operation manual for pipe freeze protection and flow maintenance
XL-Trace System Installation and Operation manual for pipe freeze protection and flow maintenance Thermal building solutions WWW.PENTAIRTHERMAL.COM Important Safeguards and Warnings WARNING: FIRE AND SHOCK
Heating Cables. For Industry Tracing
Heating Cables For Industry Tracing FATI-FFHT-X 1/2 FFHT-X Features Energy efficient, automatically varies its power output in response to pipe temperature changes. Easy to install, can be cut to any length
Power Connection Kit installation instructions
Operating instructions & Parts Manual ET00 Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and
FLEXTRACE. FSG - FSG/T - FSG/TP - FSG/TF Self-regulating cables for refrigeration. Applications. Characteristics
FSG.GB/07/05.07 FLEXTRACE TEMPERATURE MAINTENANCE SYSTEMS www.flexelec.com FSG - FSG/T - FSG/TP - FSG/TF Self-regulating cables for refrigeration Characteristics Can be cut to length on site. Will not
Emergency De-Icer (HSTAT-R Series) Instruction Manual
Emergency De-Icer (HSTAT-R Series) Instruction Manual Read and understand this material before operating or servicing this heater. Failure to understand how to safely operate these heaters could result
ELEKTRA SelfTec Antifrost System
E ELEKTRA SelfTec Antifrost System ELEKTRA selfregulating heating cables: Have the Certificate of the Association of Polish Electrical Engineers entitling to mark the product with the safety mark "B";
TRACEADO eléctrico AKO-TRACE Installation, testing and maintenance of Electrical Heat Tracing with constant wattage parallel heating cables
7210H051 Ed.07 GB TRACEADO eléctrico AKO-TRACE Installation, testing and maintenance of Electrical Heat Tracing with constant wattage parallel heating s 0- Introduction 1- Material reception and testing
Segurança. Segurança. MSB/HSB Heating System. Compulsório. Compulsório. Operation Manual/Installation Instructions. Cold applied connection technology
Segurança TC RU C-DE.ГБ06.B.00230 OCP 0004 Compulsório INMETRO Operation Manual/Installation Instructions Segurança MSB/HSB Heating System Cold applied connection technology Compulsório Type 27-1.80-...0/...
EXT5R & EXT3T Series External Heating Cable System for Pipe Freeze Protection
EXT5R & EXT3T Series External Heating Cable System for Pipe Freeze Protection Installation Instructions General Information EXT systems are designed for use on all metal and non-metal pipe materials including
channel damage the internal components and the weight may break the internal wiring or flexible strip.
YOU MAY NEED End cap Power adaptor Connector pin Splicing pin Connector Silicone glue Pliers Power converter Converter + surge protector Heat shrink Aluminium channel Heat gun NT cutter IMPORTANT NOTES
FLX TM Self-Regulating Winterization/Freeze Protection INSTALLATION PROCEDURES
FLX TM Self-Regulating Winterization/Freeze Protection INSTALLATION PROCEDURES FLX TM Self-Regulating Refer to the FLX Cable Testing Report for required recording of test data and circuit information.
RockLap H&V Pipe Sections
CONSTRUCTION TYPE: HVAC PIPEWORK JANUARY 2017 RockLap H&V Pipe Sections For rapid, efficient pipework insulation are strong lengths of pre-formed insulation with a one piece, factory applied foil facing
QAA 132 Operating Manual for Heat Tracing System ELSR-MA and ELSR-WA
QAA 132 Operating Manual for Heat Tracing System ELSR-MA and ELSR-WA eltherm Canada Inc. 1440 Graham s Lane, Unit 5 Burlington Ontario L7S 1W3 Canada Phone: +1 (289) 812-6631 Fax: +1 (844) 325-6750 E-Mail:
Introduction to Heat Trace Cable Systems
Introduction Introduction to Heat Trace Cable Systems Tempco s Heat Trace Cables are used to counteract the effects of heat dissipation from process pipe and equipment through its insulation (if any).
PRO-Tect Pipe Freeze Protection Self-Regulating Heating Cable Install Manual (PT-Series)
PRO-Tect Pipe Freeze Protection Self-Regulating Heating Cable Install Manual () Free Design Service 24/7 Installation Support (800) 875-5285 www.warmlyyours.com Assembly Tools Needed Utility knife Wire
TubeTrace Tubing Bundles
for Custom CEMS and Analytical Umbilicals English Units Receiving, Storing and Handling... 1. Inspect materials for damage incurred during shipping. Report damages to carrier for settlement. 2. Identify
DS Series Solar System
DS Series Solar System Permit information Consol 30-58-1800 Collector Flat mount on Colorsteel Plumdeck roofing Valve vent, Open loop http:// www.consolsolar.co.nz 21 Page 1 of This system is an evacuated
y, [ S Technical Symbols r = mm Radius Weight (total) new
Technical Symbols 0 y, [ S Weight (total) Length (total) Diameter (also dia. of head, of shaft, of points) Diameter Conformity with EU guidelines r = mm Radius new Catalogue page 576 Pipe Bending Systems
3M Self Regulating Heating Cables
2 Construction & Function 3M Self Regulating Heating Cables Introduction: 3M Canada and Thermon Manufacturing Company have entered into a strategic alliance to market the commercial line of heat tracing
NORTH AMERICAN APPLICATION MANUAL PIPES AND FITTINGS
NORTH AMERICAN APPLICATION MANUAL PIPES AND FITTINGS Tel.: 919.304.3846 info.us@armacell.com www.armacell.us 1 Armaflex Application Manual Content Pipes and Fittings...16 Insulating pipes using Armaflex
CARAPACE Job-Ready Freeze Protected Polyethylene Pipe System
CARAPACE Job-Ready Freeze Protected Polyethylene Pipe System CARAPACE GFC shown Cord-Set Version Must be protected with GFCI (Ground Fault Circuit Interrupter) Unpack carefully. Do not use sharp knives
THERMAL MANAGEMENT
DESIGN GUIDELINES XL-TRACE LSZH SELF-REGULATING HEATING CABLES FOR PIPE FREEZE PROTECTION SYSTEMS THERMAL MANAGEMENT WWW.PENTAIRTHERMAL.COM PIPE FREEZE PROTECTION SYSTEM OVERVIEW SBS Control Panel T-Connection
Manual Electronic Identification Systems BIS Read/Write Heads C3-slk_716464_E_1110.p65 Deutsch bitte wenden!
C3-slk_716464_E_1110.p65 1 Manual Electronic Identification Systems BIS s Deutsch bitte wenden! 2 No. 716 464 D/E Edition 1110 Subject to modification. Replaces edition 1104. Balluff GmbH Schurwaldstrasse
Electric Heat Tracing INSTALLATION PROCEDURES
Electric Heat Tracing INSTALLATION PROCEDURES Electric Heat Tracing Complete Electric Heat Tracing System... Illustration A: Typical Heat Tracing Installation A complete electric heat tracing system will
ft. ft Signature Balsam Fir Tree ITEM Item 68607
7.5 7.5 ft. ft Signature Balsam Fir Tree ITEM Item 68607 PARTS LIST A. BOTTOM B. MIDDLE C. TOP D. TREE STAND NUMBER OF PERSONS RECOMMENDED FOR ASSEMBLY: 2 SKU 68607 7.5 Signature Balsam Fir 2114 TIPS STANDARD
Table of Contents 2.0 EIGERFLEX CPE. 2.0 Table of Contents
Table of Contents 2.0 2.0 Table of Contents 2.1 System description 2.100 System description (general) 2.105 System description (data) 2.115 DN 20 - DN 40 with frost protection strip, Ø carrier pipe 25-50
COOLING SYSTEM - V8. Cooling system component layout DESCRIPTION AND OPERATION
Cooling system component layout 26-2-2 DESCRIPTION AND OPERATION 1 Heater matrix 2 Heater return hose 3 Heater inlet hose 4 Heater inlet pipe 5 Throttle housing 6 Connecting hose 7 Throttle housing inlet
Specification for Heated Instrument Tubing in Process Applications* (March 29, 2007)
Specification for Heated Instrument Tubing in Process Applications* (March 29, 2007) 1.0 SCOPE This specification outlines the minimum requirements for electrically traced or steam/fluid traced instrument
HOTLINE Insulated Tubing for Steam Supply & Condensate Returns Lines
HOTLINE Insulated Tubing for Steam Supply & Condensate Returns Lines PVC jacket - Deg C (optionally PUR material) Glass fibre thermal insulation Process tube(s) Heat reflective tape Electrical heating
Type LT Self-Regulating Heater Cable For use in Ordinary and Hazardous (Classified) Locations
A, I, A, Operating Principle The parallel bus wires apply voltage along the entire length of the heater cable. The conductive core provides an infinite number of parallel conductive paths permitting the
Product Overview. Application
Self-Regulating SC, SC/H Series-resistance heating cables for longline systems Electrical freeze protection for long pipelines in both nonhazardous and hazardous locations Power-Limiting Mineral Insulated
ET-PWR-END-KIT Installation Instructions (part #JSR00)
(part #JSR00) Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety
Segurança. Segurança. PSB Heating System Heat shrink technology. Compulsório. Compulsório. Operation Manual/Installation Instructions
Segurança TC RU C-DE.ГБ06.B.00230 OCP 0004 Compulsório INMETRO Operation Manual/Installation Instructions Segurança PSB Heating System Heat shrink technology Compulsório Type 27-1680-...0/... OCP 0004
PSI Anti-Corrosion Tape
General information Technical specifications Requirement evaluation Application instructions Certificates PSI Anti-Corrosion Tape 8 Pipeline Accessories 85 The Systems PSI anti-corrosion tapes have been
Solutions in Rail Heating Systems. Rail Heating Proposal. Innovations in heat tracing
Solutions in Rail Heating Systems Rail Heating Proposal Innovations in heat tracing Innovations in heat tracing eltherm our company How can we protect antennas from ice in frosty weather? How can we transport
liniled Side liniled Side
lini Side lini Side lini Side is a flexible Led strip with a special co-extrusion technology. Light will be emitted at the side through the built-in reflection. Therefore it is ideal for applications where
Power-Limiting Cables
Power-Limiting Cables This section provides general design guidelines for power-limiting heat-tracing systems installed on insulated metal pipes. For other applications or design assistance, contact your
Technical data. Standards: IEC/EN EN 574 EN 418. powder-coated Protection class: IP 65. Cable section: max. 1.5 mm V I the :
55 Two-hand control panels SEP System components 460 240 190 30 Standards: IEC/EN 60947-5-5 EN 574 EN 418 cast aluminium, powder-coated Protection class: IP 65 Cable section: max. 1.5 mm 2 U i : 440 V
FIST-GSS2. Fist Generic Splicing Shelf MK2. Contents. 1 Introduction. 2 General. 3 Installation of the shelf. 5 Termination of the pigtails
FIST-GSS2 I N S T A L L A T I O N I N S T R U C T I O N Fist Generic Splicing Shelf MK2 Contents 1 Introduction 2 General 2.1 Kit content 2.2 Tools 2.3 Optional extra s 3 Installation of the shelf 3.1
COOLEDGE LINE INSTALLATION INSTRUCTIONS
5 YEAR SYSTEM WARRANTY 5 YEAR SYSTEM WARRANTY COOLEDGE LINE INSTALLATION INSTRUCTIONS Please read these instructions PRIOR to installation. Installation must be completed by a qualified electrician in
INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063
INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063 PARTS LIST: 1 Grille Guard 2 10-1.5mm Nylon Lock Nuts 1 Driver/Left Frame Mounting Bracket 4 12mm Plastic Washers 1
IP65 COOLEDGE TILE EXTERIOR R2 INSTALLATION MANUAL. Exterior TILE Jumper Cable. Exterior Cutout TILE. Cable Clamp. T-Cable.
5 YEAR SYSTEM WARRANTY 5 YEAR SYSTEM WARRANTY COOLEDGE TILE EXTERIOR R2 INSTALLATION MANUAL Exterior Cutout TILE Exterior TILE Jumper Cable T-Cable End Cap Cable Clamp Power Supply Control Module Waterproof
RT FlexiPanel TM Tank and Vessel Heating Panel
RT FlexiPanel TM Tank and Vessel ing Panel Application... Metallic Tank and Vessel ing The RT FlexiPanel is a self-contained, high performance flexible heating panel designed specifically for use on metallic
Installation Instructions
K-Series Constant-Wattage Heating Cable Installation Instructions Read and understand this material before installing this heater. Failure to understand how to safely install the heater could result in
VERTICAL MULTI-STAGE CENTRIFUGAL PUMPS
Installation and Operating Instructions VERTICAL MULTI-STAGE CENTRIFUGAL PUMPS Models 1, 3, 5, 10, 15, 20, 32, 45, 64, 90 1. Model numbering and nameplate format 1.1 Model numbering Example: SBI / SBN
C Power Connection Kit
1548-4000C Power Connection Kit For use with Dekoron 2700 Family of Heating Cables Installation Instructions Kit Description The Dekoron 1548-4000C electrical connection kit distirbuted by Heat-Line is
Installation Instructions CONSTANT WATT (CW) AND SELF-REGULATING (SR) PIPE TRACING CABLES
Installation Instructions CONSTANT WATT (CW) AND SELF-REGULATING (SR) TRACING S CONTENTS page Constant Watt Cable Self-Regulating Cable SECTION 1. OVERVIEW 1.1 Precautions... 2 1.2 Cable and components...
Type LT Self-Regulating Heater Cable For use in Ordinary (Unclassified) and Hazardous (Classified) Locations
F, G ;, Class I, Class Groups F, G; Operating Principle The parallel bus wires apply voltage along the entire length of the heater cable. The conductive core provides an infinite number of parallel conductive
Bending Systems. Pipe bending pliers no How do I find the right bending tool 615. Manual pipe bender - Manual bending tool
612 613 Bending Systems How do I find the right bending tool 615 Pipe bending pliers no. 2415 618 Manual pipe bender - Draw bending operation 619 Manual bending tool sets no. 243 619 Manual bending tool
IU0U automatic charger Read these instructions carefully before the installation and commissioning and keep them in a safe place. Pass it on to the buyer in case of the further sale of the system. Contents
Technical data sheet LÜTZE SUPERFLEX PLUS M (C) PUR SERVO 0.6/1 kv Supply line for Bosch Rexroth and other systems For highest requirements
PVC servo cables C-track compatible shielded Subject to technical modification 111270 Identification Type SU+M(C)P SE(4G1,0+2 (2 0,75))UL 1KV OR INK Description* INK 0653 Use/Application/Properties Application
Cable pulling technology
Cable pulling technology Fish tapes/pulling rods 556 Polyester 556 Perlon 556 Nylon 556 Steel 557 Flex-O-Twist speed flex leader 557 Fibreglass cable pulling rods 557 Cable pulling systems 55 With Polyester
BEECHJET 400A TOWING AND TAXIING
TOWING AND TAXIING DESCRIPTION AND OPERATION Towing involves ground movement of the airplane without engine operation and is the preferred method of airplane positioning since it provides more safety and
Installation Guide The RSi brief overview:
Electronic Rust Protection Installation Guide The RSi brief overview: The RustStop RSi Industrial uses a 6 channel output system to drive up to 18 anodes (Rust Magnets ) Each channel has its own output
Installation, Maintenance and Operation manual 4 Submersible sand fighter pump. Type: SSFP - Series
Installation, Maintenance and Operation manual 4 Submersible sand fighter pump Type: SSFP - Series Prakash Pump Warranty We guarantee our products, for the period of 24 months from the date of purchase.
Revision THERMO TECHNOLOGIES. USDT 2001 Differential Controller. Installation and User s Guide
Revision 8 THERMO TECHNOLOGIES USDT 2001 Differential Controller Installation and User s Guide USDT 2001 DIFFERENTIAL CONTROLLER Installation and User s Guide Table of Contents Introduction General Information
Limitor -G General Purpose Fuses
Limitor -G General Purpose Fuses HIGH VOLTAGE IEC FUSES DIN HV GENERAL PURPOSE FUSES FOR TRANSFORMERS FEATURES & BENEFITS Mersen HV fuse-links have been used for reliable protection in high-voltage switchgear
FIST-GSS2 FIST-GSS3. Fist Generic Splicing Shelf. Contents. 1 Introduction. 2 General. 3 Installation of the shelf. 5 Termination of the pigtails
FIST-GSS2 FIST-GSS3 I N S T A L L A T I O N I N S T R U C T I O N Fist Generic Splicing Shelf Contents 1 Introduction 2 General 2.1 Kit content 2.2 Tools 3 Installation of the shelf 3.1 Mounting the shelf
High Power Low Ohm Chip Resistors. Size W, W, /2W
WW25P, WW20P, WW12P ±1%, ±5% 47mΩ~976mΩ High Power Low Ohm Chip Resistors Size 2512 2W, 2010 1W, 1206 1/2W *Contents in this sheet are subject to change without prior notice. Page 1 of 7 ASC_WW25P-20P-12P_V08
Index 2. Content 2. Technical 3. Specifications 3. Installation 4
Clip HP Floor Wall Ceiling 180º 150 cm Driver excl. 50.000 h 14º 16º 30º 42º 120º 16x40º Luxeon/Cree IP40 3000K 4000K 500 ma 8W / 25cm 1-10V Phase CRI>80 dimmable dimmable 2700K INDEX Manual Version 2.0
Supplementary instructions. Air cooling - FIBERTRAC 31. Active air cooling system for radiation-based sensors. Document ID: 50339
Supplementary instructions Air cooling - FIBERTRAC 31 Active air cooling system for radiation-based sensors Document ID: 50339 Contents Contents 1 Product description 1.1 Configuration... 3 2 Mounting
Installation handbook
Installation handbook INDEX SAFETY INSTRUCTIONS 4 5 GENERAL INSTALLATION DETAILS 6 10 Installation Information 6 Planning 7 10 Tools 10 PIPE INSTALLATION 11 16 Working with PVC 11 12 Important Pipe Installation
Flexible insulation to prevent condensation and energy losses
Flexible insulation to prevent condensation and energy losses Powered by TCPDF (www.tcpdf.org) Reliable condensation control Effective reduction of thermal losses Built-in Microban antimicrobial protection
REFRIGERATION PARTS SOLUTION
REFRIGERATION PARTS SOLUTION Do It Yourself Kit Assembly and Installation Manual Full Gauge Digital Thermostat Retrofit Kit Digital Thermostat Upgrade for Danfoss BD Series of DC Compressor Systems with
Table of Contents COOLMANT. 2.0 Table of Contents
CLM 2.0 Table of Contents 2.0 Table of Contents 2.1 System description 2.100 System description (general) 2.105 System description (data) 2.115 COOLMANT range, Ø 125 - Ø 315 / SDR 11/SDR 17 (bars) 2.2
Self-Regulating Cables
Self-Regulating 1. Self- Regulating 2. Power- Limiting This step-by-step design guide provides the tools necessary to design a self-regulating heat-tracing system for insulated pipes and tubing. For other
WK25S WK20S WK10S WK12S WK08S WK06S. Thick Film Power Surge Chip Resistors AEC Q-200 Qualified Size 2512, 2010, 1210, 1206, 0805, 0603
WK25S WK20S WK10S WK12S WK08S WK06S ±5% 5%, ±10 10%, ±20 20% Thick Film Power Surge Chip Resistors AEC Q-200 Qualified Size 2512, 2010, 1210, 1206, 0805, 0603 *Contents in this sheet are subject to change
SELF-REGULATING CABLES
Self-Regulating SELF-REGULATING CABLES This step-by-step design guide provides the tools necessary to design a selfregulating heat-tracing system for insulated pipes and tubing. For other applications
FLEXTRACE. Power (W/m) Dimensions
FST.GB/07/05.07 FLEXTRACE TEMPERATURE MAINTENANCE SYSTEMS www.flexelec.com FST - FST/T - FST/I - FST/TP - FST/TF Self-regulating cables Characteristics Can be cut to length on site. Will not self-destruct
POWERHEAT TYPE AHT TERMINATION INSTRUCTIONS. Ref TK/AHT Issue C Date 16 August 1999
STOCKPORT, ENGLAND, TEL: 0161-430 8333 POWERHEAT TYPE AHT TERMINATION INSTRUCTIONS PLEASE READ THE INSTRUCTIONS BEFORE PROCEEDING Recommended Tools ANNEX B Ref TK/AHT Issue C Date 16 August 1999 Heavy
HWAT -System. Installation and Maintenance Manual. Hot water temperature maintenance system-hwat for pipes with thermal insulation
Installation and Maintenance Manual HWAT -System Hot water temperature maintenance system-hwat for pipes with thermal insulation Thermal management solutions EN-RaychemHWATsystem-IM-INST293 R1 Important
Self-regulating cables
Self-Regulating Self-regulating cables This step-by-step design guide provides the tools necessary to design a selfregulating heat-tracing system for insulated pipes and tubing. For other applications
Installation: 4.b. Using Armaflex sheet insulation on pipes. Application to pipes. Application to fittings
4.b. Using Armaflex sheet insulation on pipes Application to pipes 1. Apply Armaflex Sheet Insulation on pipes larger than 5 IPS. Cut the sheet insulation to proper width, permitting it to fit loosely
Handyman Motor Capacitor Meter PART NO
Handyman Motor Capacitor Meter PART NO. 2225174 To test a motor-run capacitor in the field with no capacitance meter at hand, you had to hook up the capacitor through an extension cable to a 120V wall
The Separator arrangements depend on the application (see order example or separator options).
SLE Energy chains individual solutions large dimensions simple handling The order for a steel chain SLE should contain the following data: Type / Radius x Length / Width - Connector Arrangement ; Separator