Tranquilizer. Surge Suppressors for Air-Driven Diaphragm Pumps. Metallic Construction. Table of Contents

Transcription

1 SERICE & OPERTI MUL Original Instructions Quality System ISO900 Certified Environmental Management System ISO400 Certified Tranquilizer Surge Suppressors for ir-driven Diaphragm Pumps Metallic Construction See pages 5 and 6 for TEX ratings Table of Contents Tranquilizer General Information... Product Model omenclature..., 3 Materials and Operating Temperatures... 3 Dimensions... 4, 5 Installation Guide... 6 Tranquilizer Options... 7 Grounding the Tranquilizer... 8 Service & Operating Instructions... 9 Safety Information... 9 Materials Codes... 0 Repair Parts List... Parts Drawing... 3 CE Declaration of Conformity - Machinery... 4 CE Declaration of Conformity - TEX... 5 Explanation of TEX Certification... 6 CE Declaration of Conformity - Regulation EC 935/ Warren Rupp, Inc. Unit of IDEX Corporation 800. Main St., P.O. Box 568, Mansfield, Ohio US Telephone (49) Fax (49) Models T, T5, T½, T40, T, T50, T3 & T80 tranqmsm-rev084

2

3 Tranquilizer WITHOUT SUPPREOR WITH SUPPREOR Quality System ISO900 Certified Environmental Management System ISO400 Certified DISCHRGE PREURE PUMP CYCLI RTE early surge-free flow. Steadier pressures. Less shock to pipes. ir-operated diaphragm pumps offer a wide range of benefits not available in any other type of pump. However, in some applications, pulsations in the discharge flow may be undesirable. Pulsation can be virtually eliminated by installing a Warren Rupp Tranquilizer. t initial and subsequent start-ups... air cushion is quickly established by liquid pressure pushing diaphragm upward, permitting entrance of air into air chamber, until the balancing air cushion causes the diaphragm to center at its mid-stroke normal operating position. During normal continuous operation thereafter... the diaphragm always flexes at its mid-range position to absorb discharge pulsations against the adjoining air cushion already established. In event of change in pumped liquid pressure... the air cushion pressure is automatically increased or decreased as required to compensate for the change... always maintaining constant volume of air cushion, and the diaphragm always operating at its mid-position. When liquid flow stops and liquid pressure is released... the air in air chamber is also exhausted to atmosphere. Tranquilizer utomatically maintains a constant volume of air cushion for most effective surge suppression, regardless of pump pressure. utomatically self-charging and self-venting to maintain most efficient air cushion pressure... no more precharge pressure calculations or guesswork, no manual pressurizing, no periodic pressure checking. ir cushion separated from product by flexible diaphragm... prevents product aeration. External visual indication provides constant evidence of performance. Simple to install. ttention-free. Models T and T5 -inch Tranquilizer for use with -inch pumps ir supply connection is ¼" PT external pipe thread. Maximum Operating Pressure 5 psi. Models T½ and T40 ½-inch Tranquilizer for use with ½-inch pumps ir supply connection is ¼" PT external pipe thread. Maximum Operating Pressure 5 psi. Models T and T50 Design Level -inch Tranquilizer for use with ½, -inch pumps ir supply connection is ¼" PT external pipe thread. Maximum Operating Pressure 5 psi. Models T3 and T80 Design Level 3-inch Tranquilizer for use with 3-inch pumps ir supply connection is ¼" PT external pipe thread. Maximum Operating Pressure 5 psi. Models T, T5, T½, T40, T, T50, T3 & T80 tranqmsm-rev084 Page

4 Materials of Construction: Type Code Diaphragm Design Level Wetted Parts Porting (Internal Tapered Threads) Type Code Diaphragm Design Level Wetted Parts Porting (Internal Tapered Threads) Porting Flange Style Shipping Weight lbs./kg Tranquilizer Model T Tranquilizer Model T5 B-- B " PT B-- B " BSPT 4 / 6.35 H-- H " PT H-- H " BSPT 4 / " PT -- " BSPT 4 / " PT -- " BSPT 4 / 6.35 S-- S " PT S-- S " BSPT 4 / " PT -- " BSPT 4 / 6.35 B-- B " PT B-- B " BSPT 8 / 8.6 F-- F " PT F-- F " BSPT 8 / 8.6 * H-- H " PT -- " PT -- " PT * H H " BSPT " BSPT " BSPT 8 / / / 8.6 S-- S " PT -- " PT S-- -- S " BSPT " BSPT 8 / / 8.6 Tranquilizer Model T½ Tranquilizer Model T40 B-- B ½" PT B-- B ½" BSPT 8 /.7 -- ½" PT -- ½" BSPT 8 /.7 -- ½" PT -- ½" BSPT 8 /.7 -- ½" PT -- ½" BSPT 8 /.7 B-- B ½" PT B-- B ½" BSPT 35 / 5.9 F-- F ½" PT F-- F ½" BSPT 35 / 5.9 * -- ½" PT * -- ½" BSPT 35 / ½" PT -- ½" BSPT 35 / ½" PT -- ½" BSPT 35 / 5.9 Tranquilizer Model T Design level Tranquilizer Model T50 Design level B-- B " PT B-- B " BSPT 8 /.7 I-- I " PT I-- I " BSPT 8 /.7 -- " PT -- " BSPT 8 /.7 -- " PT -- " BSPT 8 /.7 S-- S " PT S-- S " BSPT 8 /.7 -- " PT -- " BSPT 8 /.7 B-- B " PT B-- B " BSPT 35 / 5.9 I-- I " PT I-- I " BSPT 35 / " PT -- " BSPT 35 / " PT S-- S " PT -- " PT B-- B " PT F-- F " PT -- S-- -- B-- F-- " BSPT 35 / 5.9 S " BSPT 35 / 5.9 " BSPT 35 / 5.9 B " BSPT 35 / 5.9 F " BSPT 35 / 5.9 tranqmsm-rev084 Page Models T, T5, T½, T40, T, T50, T3 & T80

5 Materials of Construction continued: Tranquilizer Model T Design level, continued Type Diaphragm Design Wetted Porting Porting Code Level Parts (Internal Tapered Flange Style Threads) Tranquilizer Model T50 Design level, continued Type Diaphragm Design Wetted Porting Porting Code Level Parts (Internal Tapered Flange Style Threads) Shipping Weight lbs./kg * " PT " PT * " BSPT " BSPT 35 / / " PT -- " BSPT 35 / 5.9 I--HC I HC " PT I--HC I HC " BSPT 35 / HC --HC HC HC " PT " PT --HC --HC HC ½" BSPT ½" BSPT 35 / / HC HC " PT --HC HC ½" BSPT 35 / 5.9 Tranquilizer Model T3 Design level Tranquilizer Model T80 Design level B-- B 3" SI Style B-- B P0 80 mm DI 89 / 40.4 I-- I 3" SI Style I-- I P0 80mm DI 89 / " SI Style -- P0 80mm DI 89 / " SI Style -- P0 80mm DI 89 / " SI Style -- P0 80mm DI 89 / 40.4 B-- B 3" SI Style B-- B P0 80mm DI 09 / 49.4 I-- I 3" SI Style I-- I P0 80mm DI 09 / " SI Style -- P0 80mm DI 09 / " SI Style -- P0 80mm DI 09 / " SI Style -- P0 80mm DI 09 / 49.4 B-- B 3" SI Style B-- B P0 80mm DI 05 / 47.6 * -- 3" SI Style * -- P0 80mm DI 05 / " SI Style -- P0 80mm DI 05 / " SI Style -- P0 80mm DI 05 / 47.6 Meaning of bbreviations: Kit available to convert to top porting = luminum B = itrile = Cast Iron F = FD White itrile H = Hytrel I = EPDM = eoprene * = eoprene Backup/PTFE Overlay S = Santoprene = FKM (Fluorocarbon) = Stainless Steel HC = lloy C *Models equipped with stainless steel and PTFE wet end components are compliant with EC 935/004 - Materials in food contact. Hytrel are registered tradenames of E.I. du Pont. Santoprene is a registered tradename of Exxon Mobil Corp. Tranquilizer is a registered tradename of Warren Rupp, Inc. MTERILS ITRILE: General purpose, oil-resistant. Shows good solvent, oil, water and hydraulic fluid resistance. Should not be used with highly polar solvents like acetone and MEK, ozone, chlorinated hydrocarbons and nitro hydrocarbons. EOPREE: ll purpose. Resistant to vegetable oils. Generally not affected by moderate chemicals, fats, greases and many oils and solvents. Generally attacked by strong oxidizing acids, ketones, esters, nitro hydrocarbons and chlorinated aromatic hydrocarbons. HYTREL : Good on acids, bases, amines, and glycols at room temperature. IRGI PTFE: Chemically inert, virtually impervious. ery few chemicals are know to chemically react with Teflon, molten alkali metals, turbulent liquid or gases, fluorine and a few fluoro-chemicals such as chlorine trifluoride or oxygen difluoride which readily liberate free fluorine at elevated temperatures. FKM: Shows good resistance to a wide range of oils and solvents; especially all alipphatic, aromatic and halogenated hydrocarbons, acids, animal and vegetables oils. Hot water or hot aqueous solutions (over 70 F) will attack FKM. EPDM: Shows very good water and chemical resistance. Has poor resistance to oil and solvents, but is fair in ketones and alcohols. STOPREE : Injection molded thermoplastic elastomer with no fabric layer. Long mechanical flex life. Excellent abrasion resistance. STILE STEEL: CF-8M equal to or exceeding STM specification 743 for corrosion resistant iron chromium, iron chromium nickel, and nickel based alloy castings for general applications. Commonly referred to as 36 Stainless Steel in the pump industry. LLOY C: CW-MW equal to or exceeding STM 494 specification for nickel and nickel alloy castings. Operating Temperatures Maximum Minimum 90 F 88 C 00 F 93 C 0 F 04 C 0 F 04 C 350 F 77 C 80 F 38 C 75 F 35 C - 0 F - 3 C -0 F -3 C -0 F -9 C -35 F -37 C -40 F -40 C -40 F -40 C -40 F -40 C For specific applications, always consult the Warren Rupp "Chemical Resistance Chart". II G c T5 II 3/ G c T5 II D c T00 o C See page 6 for TEX Explanation of Type Examination Certificate. Models T, T5, T½, T40, T, T50, T3 & T80 tranqmsm-rev084 Page 3

6 Model T ir Inlet ¼" PT (external) fitting FLUID Port - " PT FULLY EXTEDED Model T5 ir Inlet ¼" PT (external) fitting FLUID Port - " BSP tapered thread FLUID PORT " PT " BSP CETERED FULLY CLOSED /4" PT DRI PORT Model T½ ir Inlet ¼" PT (external) fitting FLUID Port - ½" PT FULLY EXTEDED FULLY CLOSED Model T40 ir Inlet ¼" PT (external) fitting FLUID Port - ½" BSP tapered thread FLUID PORT /" PT /" BSP CETERED ll Dimensions ±.3" (3mm) tranqmsm-rev084 Page 4 Models T, T5, T½, T40, T, T50, T3 & T80

7 Model T Design Level ir Inlet ¼" PT (external) fitting " PT Fluid Port FULLY EXTEDED FULLY CLOSED Model T50 Design Level ir Inlet ¼" PT (external) fitting " BSP(Tapered) Fluid Port FLUID PORT " PT " BSP CETERED Model T3 Design Level ir Inlet ¼" PT (external) fitting FLUID Port Model T80 Design Level ir Inlet ¼" PT (external) fitting FLUID Port FULLY CLOSED FULLY EXTEDED (Tapered) SI P0 80mm DI Flange M6x 8 holes on a 60mm diameter Bolt Circle FLUID PORT 3" BSP CETERED ll Dimensions ±.3" (3mm) Models T, T5, T½, T40, T, T50, T3 & T80 tranqmsm-rev084 Page 5

8 ISTLLTIO GUIDE Top Discharge Ball or Flap alve Unit 3 4 vailable from Warren Rupp Tranquilizer Filter/Regulator Lubricator ir Dryer CUTIO The air exhaust should be piped to an area for safe disposition of the product being pumped, in the event of a diaphragm failure. 3 4 tranqmsm-rev084 Page 6 Models T, T5, T½, T40, T, T50, T3 & T80

9 Tranquilizer Options HC T Designed for " pumps. 5 psi 8.6 bar Selfcharging. Selfventing. ¼" PT (external " PT 3 5/8" to 5 /8" height (346mm to 384mm) 9" diameter (9mm) PT(F) T5 Designed for " pumps. 5 psi 8.6 bar Selfcharging. Selfventing. ¼" PT (external " BSPT (tapered internal 3 5/8" to 5 /8" height (346mm to 384mm) 9" diameter (9mm) PT(F) T½ Designed for " and ½" pumps. 5 psi 8.6 bar Selfcharging. Selfventing. ¼" PT (external ½" PT (internal 9 7/8" to. 3/8" height (505mm to 543mm) 0½" diameter (67mm) PT(F) T40 Designed for " and ½" pumps. 5 psi 8.6 bar Selfcharging. Selfventing. ¼" PT (external ½" BSPT (tapered internal 9 7/8" to. 3/8" height (505mm to 543mm) 0½" diameter (67mm) PT(F) T Design Level Designed for ½ and " pumps. 5 psi 8.6 bar Selfcharging. Selfventing. ¼" PT (external " PT (internal 0¼" to 3 3/6" height (54mm to 589mm) ½" diameter (37mm) PT(F) T50 Design Level Designed for ½ and " pumps. 5 psi 8.6 bar Selfcharging. Selfventing. ¼" PT " BSPT (tapered internal 0¼" to 3 3/6" height (54mm to 589mm) ½" diameter (37mm) PT(F) T3 Design Level Designed for 3" and 4" pumps. 5 psi 8.6 bar Self- Charging. Selfventing. ¼" PT 3" 50# nsistyle flange or 3" PT internal thread 0 /8" to 3 /8"m height (5mm to 587mm) 6 3/6" diameter (4mm) PT(F) T80 Design Level Designed for 3" and 4" pumps. 5 psi 8.6 bar Self- Charging. Selfventing. ¼" PT 3" BSPT (tapered internal or 80mm DI-style Flange 0 /8" to 3 /8"m height (5mm to 587mm) 6 3/6" diameter (4mm) PT(F) L = luminum B = itrile = Cast iron E = EPDM = eoprene T = Overlay, eoprene with irgin PTFE T = irgin PTFE = FKM (Fluorocarbon) S = Santoprene HC= lloy C = lloy 36 stainless steel Models T, T5, T½, T40, T, T50, T3 & T80 tranqmsm-rev084 Page 7

10 Grounding The Tranquilizer One eyelet end is fastened to the surge suppressor hardware. The other end is installed to a true earth ground. WRI Take action to prevent static sparking. Fire or explosion can result, especially when handling flammable liquids. The pump, piping, valves, containers or other miscellaneous equipment must be grounded. This optional 8 foot long (44 centimeters) Ground Strap ( ) is available for easy ground connection. To reduce the risk of static electrical sparking, this surge suppressor must be grounded. Check the local electrical code for detailed grounding instruction and the type of equipment required. tranqmsm-rev084 Page 8 Models T, T5, T½, T40, T, T50, T3 & T80

11 Tranquilizers Model T Metallic Construction SERICE D OPERTI ISTRUCTIOS This Warren Rupp Tranquilizer is a completely automatic diaphragm fitted surge suppressor to reduce the flow and pressure pulsations in a pumping system characteristic of reciprocating type pumps. Principle of Operation: The Tranquilizer uses a flexible diaphragm to separate a liquid chamber from compressed air chambers. rod connected to the center of one diaphragm activates the air inlet and exhaust valves, which automatically admit or exhaust air in the air chambers. This maintains the diaphragms in mid-range of stroke for maximum surge suppression. Installation: Locate the Tranquilizer in discharge piping as close as possible to the pump. The unit will operate in any position. Connect air inlet connection to full plant air supply line before the air regulator to pump. ot to exceed 5PSI. Service Instructions: When service is required, it is important to MKE CERTI THT ILET IR PREURE IS DISCOECTED. The diaphragms are serviced by simply removing the hex nuts or v-band, and removing the center spool casting. When irgin PTFE diaphragms are used in conjunction with the elastomeric diaphragms they are placed over the wetted sides of each elastomeric diaphragm. Inlet and exhaust air valves are located externally for easy access and service. Warranty: This unit is guaranteed for a period of five years against defective material and workmanship. IMPORTT Read these safety warnings and instructions in this manual completely, before installation and start-up of the pulsation dampener. It is the responsibility of the purchaser to retain this manual for reference. Failure to comply with the recommendations stated in this manual will damage the pulsation dampener, and void factory warranty. CUTIO Before surge suppressor operation, inspect all gasketed fasteners for looseness caused by gasket creep. Re-torque loose fasteners to prevent leakage. Follow recommended torques stated in this manual. WRI Before doing any maintenance on the pulsation dampener, be certain all pressure is completely vented from the pump, suction, discharge, piping, and all other openings and connections. Be certain the air supply is locked out or made non operational, so that it cannot be started while work is being done on the pump. Be certain that approved eye protection and protective clothing are worn all times in the vicinity of the pump. Failure to follow these recommendations may result in serious injury or death. WRI Take action to prevent static sparking. Fire or explosion can result, especially when handling flammable liquids. The pump, piping, valves, containers or other miscellaneous equipment must be grounded. See page 8. HZRD WRI POIBLE EXPLOSIO HZRD can result if,,, -Trichloroethance, Methylene Chloride or other Halogenated Hydrocarbon solvents are used in pressurized fluid systems having luminum or Galvanized wetted parts. Death, serious bodily injury and/or property damage could result. Consult with the factory if you have questions concerning Halogenated Hydrocarbon solvents. tamdlsm-rev084 Model T Page 9

12 MTERIL CODES THE LST 3 DIGITS OF PRT UMBER 000 ssembly, sub-assembly; and some purchased items 00 Cast Iron 0 Powered Metal 05 Ductile Iron 00 Ferritic Malleable Iron 05 Music Wire 080 Carbon Steel, ISI B- 00 lloy 0 0 lloy Type 36 Stainless Steel lloy Type 36 Stainless Steel (Electro Polished) lloy C 3 lloy Type 36 Stainless Steel (Hand Polished) Stainless Steel 5 30/304 Stainless Steel C Stainless Steel (Martensitic) 0 46 Stainless Steel (Wrought Martensitic) 3 40 Stainless Steel (Wrought Martensitic) 48 Hardcoat nodized luminum T4 luminum T6 luminum T6 luminum 5 04-T4 luminum (03-T35) 54 lmag 35 luminum T6 luminum T6 luminum 57 Die Cast luminum lloy # luminum lloy SR nodized luminum 6 Brass, Yellow, Screw Machine Stock 65 Cast Bronze, Bronze, SE Bronze, Bearing Type, Oil Impregnated 75 Die Cast Zinc 80 Copper lloy 305 Carbon Steel, Black Epoxy Coated 306 Carbon Steel, Black PTFE Coated 307 luminum, Black Epoxy Coated 308 Stainless Steel, Black PTFE Coated 309 luminum, Black PTFE Coated 30 PDF Coated 33 luminum, White Epoxy Coated 330 Zinc Plated Steel 33 Chrome Plated Steel 33 luminum, Electroless ickel Plated 333 Carbon Steel, Electroless ickel Plated 335 Galvanized Steel 336 Zinc Plated Yellow Brass 337 Silver Plated Steel 340 ickel Plated 34 Filled ylon 35 Food Grade Santoprene 353 Geolast; Color: Black 354 Injection Molded #03-40 Santoprene- Duro 40D +/-5; Color: RED 355 Thermal Plastic 356 Hytrel 357 Injection Molded Polyurethane 358 Urethane Rubber (Some pplications) (Compression Mold) 359 Urethane Rubber 360 itrile Rubber Color coded: RED 36 itrile 363 FKM (Fluorocarbon). Color coded: YELLOW 364 E.P.D.M. Rubber. Color coded: BLUE 365 eoprene Rubber. Color coded: GREE 366 Food Grade itrile 368 Food Grade EPDM 370 Butyl Rubber Color coded: BROW 37 Philthane (Tuftane) 374 Carboxylated itrile 375 Fluorinated itrile 378 High Density Polypropylene 379 Conductive itrile 405 Cellulose Fibre 408 Cork and eoprene 45 Compressed Fibre 46 Blue Gard 440 egetable Fibre 465 Fibre 500 Delrin Delrin Conductive cetal, ESD Conductive cetal, Glass-Filled 505 crylic Resin Plastic 506 Delrin Injection Molded PDF atural color 540 ylon 54 ylon 54 ylon 544 ylon Injection Molded 550 Polyethylene 55 Glass Filled Polypropylene 55 Unfilled Polypropylene 553 Unfilled Polypropylene 555 Polyvinyl Chloride 556 Black inyl 558 Conductive HDPE 570 Rulon II 580 Ryton 590 alox 59 ylatron G-S 59 ylatron SB 600 PTFE (virgin material) Tetrafluorocarbon (TFE) 60 PTFE (Bronze and moly filled) 60 Filled PTFE 603 Blue Gylon 604 PTFE 606 PTFE 607 Envelon 608 Conductive PTFE 60 PTFE Encapsulated Silicon 6 PTFE Encapsulated FKM 63 eoprene/hytrel 633 FKM/PTFE 634 EPDM/PTFE 635 eoprene/ptfe 637 PTFE, FKM/PTFE 638 PTFE, Hytrel/PTFE 639 itrile/tfe 643 Santoprene /EPDM 644 Santoprene /PTFE 656 Santoprene Diaphragm and Check Balls/EPDM Seats 66 EPDM/Santoprene 666 FD itrile Diaphragm, PTFE Overlay, Balls, and Seals 668 PTFE, FD Santoprene/PTFE Delrin and Hytrel are registered tradenames of E.I. DuPont. Gylon is a registered tradename of Garlock, Inc. ylatron is a registered tradename of Polymer Corp. Santoprene is a registered tradename of Exxon Mobil Corp. Rulon II is a registered tradename of Dixion Industries Corp. Ryton is a registered tradename of Phillips Chemical Co. alox is a registered tradename of General Electric Co. PortaPump, Tranquilizer and SludgeMaster are registered tradenames of Warren Rupp, Inc. tamdlsm-rev084 Model T Page 0

13 tamdlsm-rev084 Model T Page

14 ITEM O. PRT UMBER DESCRIPTIO QTY Bearing, Sleeve Body Cap Capscrew, Hex Hd 5/6-8 X 7/ Capscrew, Hex Hd 3/8-6 x / Capscrew, Hex Hd 5/6-8 x / Capscrew, Hx Hd 5/6-8 x 3/ Outer Chamber (Stainless Units) Outer Chamber Chamber Diaphragm Diaphragm Diaphragm Diaphragm Diaphragm Diaphragm Diaphragm Diaphragm, Overlay Flange, Threaded (Stainless and PTFE Units) Flange, Threaded Gasket, Flange Gasket, Flange (PTFE and FKM Units) Tube Fitting ut, Hex 5/ ut, Hex 3/8-6 (Stainless Units) ut, Hex / O-Ring Plate, Inner Diaphragm Plate, ctivator Plate, ctivator Plate, Outer Diaphragm Plate, Outer Diaphragm Plug, /4 Pipe (Stainless Units) Plug, /4 Pipe Rod, Diaphragm Rod, ctivator Seal, Shaft alve ssembly Body, alve O-Ring Poppet Spring, Retainer Spring, Compression alve ssembly Body, alve Poppet Spring, Compression O-Ring Elbow, Male Washer, Lock 5/ Washer, Flat 5/ Washer, Sealing Washer, Sealing 4 REPIR PRTS LIST and DRWI Tranquilizer Model T Metallic Construction tamdlsm-rev084 Model T Page

15 Model T * 3 6 ** 8 * Used only on PTFE fitted units ** Used only on Stainless Steel fitted units Warren Rupp, Inc. ll rights reserved. Tranquilizer is a registered tradename of Warren Rupp, Inc. Printed in U.S.. tamdlsm-rev084 Model T Page 3

16 Declaration of Conformity Manufacturer: Warren Rupp, Inc., 800. Main Street Mansfield, Ohio, 4490 US certifies that ir-operated Double Diaphragm Pump Series: HDB, HDF, M on-metallic, S on-metallic, M Metallic, S Metallic, T Series, G Series, RS Series U Series, EH and SH High Pressure, W Series, SM and SP Submersibles, and Tranquilizer Surge Suppressors comply with the European Community Directive 006/4/EC on Machinery, according to nnex III. This product has used Harmonized Standard E809:998+:009, Pumps and Pump Units for Liquids - Common Safety Requirements, to verify conformance. Signature of authorized person David Roseberry Printed name of authorized person Revision Level: F October 0, 005 Date of issue Engineering Manager Title pril 9, 0 Date of revision

17 EC Declaration of Conformity In accordance with TEX Directive 94/9/EC, Equipment intended for use in potentially explosive environments. Manufacturer: Warren Rupp, Inc. Unit of IDEX Corportion 800 orth Main Street P.O. Box 568 Mansfield, OH 4490 US pplicable Standard: E3463-: 009 E3463-5: 0 E : 0 For pumps equipped with Pulse Output TEX Option Quality B.. (0344) ODD Pumps and Surge Suppressors For Type Examination Designations, see page (back) ODD (ir-operated Double Diaphragm) Pumps EC Type Examination Certificate o. Pumps: KEM 09TEX007 X DEKR Certification B.. (0344) Meander MJ rnhem The etherlands DTE/PPROL/TITLE: 4 MY 04 David Roseberry, Engineering Manager

18 EC Declaration of Conformity TEX Summary of Markings Type Marking Listed In Pump types, SF, S5, S0, and S30 provided with the pulse output option II G Ex ia c IIC T5 II 3/ G Ex ia c IIC T5 II D Ex c iad 0 IP67 T00 o C KEM 09TEX007 X CE 0344 KEM 09TEX007 X KEM 09TEX007 X KEM 09TEX007 X on-conductive Fluids o Pump types, SF, S5, S0, and S30 provided with the integral solenoid option II G EEx m c II T5 II 3/ G EEx m c II T5 II D c IP65 T00 o C KEM 09TEX007 X CE 0344 KEM 09TEX007 X KEM 09TEX007 X KEM 09TEX007 X o Pump types, HDB½, HDB40, HDB, HDB50, HDB3, HDF, HDF5, HDF, HDF3M, PB¼, S05, SF, S5, S0, S30, SB, SB5, ST½, ST40, G5, G0, and G30, without the above listed options, no aluminum parts II G c T5 II 3/ G c T5 II D c T00 o C I M c I M c KEM 09TEX007 X KEM 09TEX007 X CE 0344 KEM 09TEX007 X KEM 09TEX007 X KEM 09TEX007 X KEM 09TEX007 X KEM 09TEX007 X o o Pump types, DMF, DMF3, HDB½, HDB40, HDB, HDB50, HDB3, HDF, HDF5, HDF, HDF3M, PB¼, S05, SF, S5, S0, S30, SB, SB5, SE½, ST, ST5, ST½, ST40, UF, G05, GF, G5, G0, and G30 II G c T5 II 3/ G c T5 II D c T00 o C KEM 09TEX007 X CE KEM 09TEX007 X KEM 09TEX007 X KEM 09TEX007 X o Surge Suppressors all types II G T5 II 3/ G T5 II D T00 o C KEM 09TEX0073 CE KEM 09TEX0073 KEM 09TEX0073 KEM 09TEX0073 o EC Type Certificate o. Pumps: KEM 09TEX007 X Type Certificate o. Pumps: KEM 09TEX007 X Type Certificate o. Suppressors: KEM 09TEX0073 Pumps marked with equipment Category II 3/ G (internal 3 G / eternal G), D, M and M when used for non-conductive fluids. The pumps are Category II G when used for conductive fluids. Pumps and surge suppressors marked with equipment Category II 3/ (internal 3 G / external G), D when used for non-conductive fluids. The pumps are Category II G when used for conductive fluids.

19 Declaration of Conformity Manufacturer: Warren Rupp, Inc., 800. Main Street, Mansfield, Ohio, 4490 US certifies that SDPIPER ir-operated Double Diaphragm Food Processing Pump Models and Tranquilizer Surge Suppressor Models comply with the European Community Regulation 935/004/EC for Food Contact Materials. TFBSSWTS600. TFBS9SWTS600. TFBSDSWTS600. TFBSLSWTS600. TFBS9TWTS600. T5BSDSWTS600. T5BSWTS600. T5BSDTS600. T5BTS600. T5BTWTS600. T5BTSTS600. Food Processing Pump Models: T0BSSWTS600. T0BSDSWTS600. T0BSTS600. T0BSDTS600. Tranquilizer Surge Suppressors: T, T5, T-/, T40, T, T50, T3, T80, T30BSSWTS600. T30BSDSWTS600. T30BSTS600. T30BSDTS600. B, TD3. Signature of authorized person David Roseberry Printed name of authorized person Revision Level: February 8, 03 Date of issue Engineering Manager Title May, 03 Date of revision