Tranquilizer. Surge Suppression for Air-Driven Diaphragm Pumps. Visit our website!
|
|
- Gavin McCormick
- 5 years ago
- Views:
Transcription
1 Quality System ISO9001 Certified Environmental Management Systems ISO14001 Certified Tranquilizer Surge Suppression for Air-Driven Diaphragm Pumps Virtually surge-free flows Steadier pressures Less vibration and noise Simple installation Variety of sizes and materials Automatically self-charging and self-venting An air cushion is established by liquid pressure pushing the diaphragm upward. This allows air to enter the chamber. The balancing air cushion keeps the diaphragm centered at mid stroke. During operation, the diaphragm(s) flex within the mid-range position, absorbing and equalizing discharge surge. If pressure changes in the system, the air cushion pressure compensates, automatically increasing or decreasing. If liquid pressure is released, air in the suppressor chamber exhausts into the atmosphere. Properly sized and installed, Tranquilizer provides virtually surge-free discharge flow. Visit our website! Without Suppression With Suppression
2 fluid port drain port ¼' Flexible hose ) fitting. Fluid Port - 1" ¼' Flexible hose ) fitting. Fluid Port - 1" BSP tapered thread fluid port Flexible hose ) fitting. Fluid Port - 2" TA50 Flexible hose ) fitting. Fluid Port - 2" BSP tapered thread fluid port fluid port ½ Flexible hose ) fitting. Fluid Port - 1½" TD40 Flexible hose ) fitting. Fluid Port - 1½" BSP tapered thread
3 Flexible hose ) fitting. Flexible hose ) fitting. 3" (Tapered) ANSI-style flange PN10 80mm DIN Flange M16x2 8 holes on a 160mm diameter Bolt Circle Installation Guidelines For best results, the factory recommends installing the surge suppressor on the discharge side of the pump. Though the more common top-ported pump is shown here, this recommendation also applies to bottom, side and dual-ported diaphragm The compressed air supply line to the surge suppressor should connect before a filter/ regulator unit limited to inlet air of 125 PSI. Flexible connections are strongly recommended. Items shown in blue are available from your local Warren Rupp Distributor. Surge Suppressor Limited to 125 PSI CAUTION The air exhaust should be piped to an area for safe disposition of the product being pumped, in the event of a diaphragm failure. TOP DISCHARGE DIAPHRAGM PUMP Available from Warren Rupp
4 Tranquilizer Options TA1 1" 13 air inlet 1" 13 5/8" to 15 1/8" height (346mm to 384mm) 9" diameter (229mm) (F) TA25 1" 13 air inlet 1" 13 5/8" to 15 1/8" height (346mm to 384mm) 9" diameter (229mm) (F) TD1½ 1" and 1½" 11 air inlet 1½" ( 19 7/8" to 21 3/8" height (505mm to 543mm) 10½" diameter (267mm) (F) TD40 1" and 1½" 11 air inlet 1½" 19 7/8" to 21 3/8" height (505mm to 543mm) 10½" diameter (267mm) (F) CE TA2 1½ and 2" 13 air inlet hose 2" ( 20 to 23 3/16" height (514mm to 589mm) 12½" diameter (317mm) (F) CE TA50 1½ and 2" 13 air inlet hose 2" 20 to 23 3/16" height (514mm to 589mm) 12½" diameter (317mm) (F) CE TA3 3" and 4" 13 air inlet hose Self- Charging. 3" 150# Ansistyle flange or 3" thread 20 1/8" to 23 1/8" height (511mm to 587mm) 16 3/16" diameter (411mm) (F) CE TA80 3" and 4" 13 air inlet hose Self- Charging. 3" or 80mm DIN-style Flange 20 1/8" to 23 1/8" height (511mm to 587mm) 16 3/16" diameter (411mm) (F) Also available from Warren Rupp : Non-metallic surge dampeners for smaller See the DA Series of surge dampeners. Now available in polypropylene, PVDF and PFA/TFE. AL = Aluminum B = Buna N C = Cast iron E = EPDM N = Neoprene T# = Overlay, Neoprene with Virgin PTFE T = Virgin PTFE V = Viton C = Alloy C (Hastelloy-C) S = Alloy 316 stainless steel Viton is a registered tradename of E.I. dupont. Tranquilizer and Warren Rupp are registered tradenames of Warren Rupp, Inc Warren Rupp, Inc. All rights reserved.
5 Quality System ISO9001 Certified Environmental Management System ISO14001 Certified Model DA05, DA07 & DA10 Metallic and Non-Metallic Surge Dampeners Use with SANDPIPER Models S05, S07, S10 and Marathon Models M05, M07, M10 pumps WITHOUT DAMPENER WITH DAMPENER Provides nearly surge-free flows. Maintains steadier pressures. Minimizes shocks in piping. Air-operated diaphragm pumps offer a wide range of benefits not available in any other type of pump. However, in some applications, pulsations in the discharge flow may be undesirable. Pulsation can be virtually eliminated by installing a Warren Rupp Surge Dampener. Designed specifically for use with the ½" and ¾" pumps, these units can provide nearly surge-free flow. Here s how it works: The Surge Dampener is manually charged with air. Once this is done, the unit s diaphragm will stroke at the same rate as the pump. This movement effectively dampens flow and pressure fluctuations. No air is consumed by the Dampener, once it is charged. PUMP CYCLING RATE Virgin PTFE diaphragms are standard. Wetted parts in polypropylene, PVDF and nylon. Minimal diaphragm movement results in long service life. Non-wetted parts are polypropylene and stainless steel. Small and modular in design, to fit the tightest installations. (See back for dimensions.) Maximum operating pressure is 100 psi (7 bar). Model & Type Code Series Size Design Wetted Non-Wetted Diaphragm Porting Hardware Options Shipping Level Material Material Material Wt. lbs./kg DAMPENER Model DA05 DA051PPTNS00. DA 05 1 P P T N S 00. 6/2.72 kg DA051PPTNT00. DA 05 1 P P T N T 00. 6/2.72 kg DA051KPTNS00. DA 05 1 K P T N S 00. 6/2.72 kg DA051KPTNT00. DA 05 1 K P T N T 00. 6/2.72 kg DA051NS00. DA 05 1 N P T N S 00. 6/2.72 kg DA051NT00. DA 05 1 N P T N T 00. 6/2.72 kg DA051APTNZ00. DA 05 1 A P T N Z 00. 6/2.72 kg DA051SPTNZ00. DA 05 1 S P T N Z 00. 6/2.72 kg DAMPENER Model DA07 DA071PPTNS00. DA 07 1 P P T N S 00. 6/2.72 kg DA071PPTNT00. DA 07 1 P P T N T 00. 6/2.72 kg DA071KPTNS00. DA 07 1 K P T N S 00. 6/2.72 kg DA071KPTNT00. DA 07 1 K P T N T 00. 6/2.72 kg DA071NS00. DA 07 1 N P T N S 00. 6/2.72 kg DA071NT00. DA 07 1 N P T N T 00. 6/2.72 kg DAMPENER Model DA10 DA101PPTAS00. DA 10 1 P P T A S / 3.25 kg DA101PPTAT00. DA 10 1 P P T A T / 3.25 kg SIZE 05 = ½" 07 = ¾" 10 = 1" WET END MATERIALS N = Nylon P = Polypropyleen K = PVDF A = Aluminum S = Stainless Steel AIR END MATERIALS P = Polypropylene DIAPHRAGM MATERIALS T = Virgin PTFE B = Buna PORTING N = (F) Inlet &Outlet A = ANSI Flange HARDWARE S = Stainless Steel T = PTFE Coated Z = Zinc Plated Steel OPTION BLOCK 0 = Standard Unit 00. = None Buna-N is a registered tradename of E.I. du Pont. Santoprene is a registered tradename of Monsanto Corp.
6 DA05 Metallic and Non-Metallic DA07 DA10 Copyright 2005 Warren Rupp, Inc. All rights reserved. Specifications are subject to improvement without notice. Printed in U.S.A. WARREN RUPP, Inc. A Unit of IDEX Corporation P.O. Box 1568 Mansfield, OH (419) Fax (419)
Model DA05 Model DA07 Model DA10
SERVICE & OPERATING MANUAL Original Instructions Quality System ISO9001 Certified Environmental Management System ISO14001 Certified Model DA05 Model DA07 Model DA10 Metallic and Non-Metallic Surge Dampeners
More informationTranquilizer Surge Suppressors for Air-Driven Diaphragm Pumps
SERVI & OPERATING MANUAL Tranquilizer Surge Suppressors for Air-Driven Diaphragm Pumps Metallic Construction Table of Contents Product and Operating Principle... Page 1 Materials and Operating Temperatures...
More informationUltra-Matic Air Valve System
Ultra-Matic Air Valve System Efficient Pumps, Competitive Upgrades and Accessories U2 Plastic Pumps Metallic Pumps Specialty Pumps Upgrade Kits Accessories Diaphragms Ultra-Matic Air Valve Technology Simple.
More informationHDF3-A Type 7 HDF4-A Type 3
Quality System ISO 9001 Certified Environmental Management System ISO 14001 Certified See pages 16 for ATEX ratings Heavy Duty Flap Valve HDF3-A Type 7 HDF4-A Type 3 Air-Operated Double Pump ENGINEERING,
More information3" Elima-Matic Pumps. Air-Operated Double Diaphragm Pumps
3" Elima-Matic Pumps Air-Operated Double Diaphragm Pumps Bulk Chemical Transfer Resins Transfer Wastewater Treatment Food Processing Filter Press Applications Tanker Car Unloading 3" Elima-Matic Pumps
More informationNDP-25 Specifications
NDP-25 Specifications Port Dimensions (46.2 GPM Max.) Intake & discharge connection: Polypropylene (PPG) Kynar (PVDF) Aluminum (ADC-12) Stainless Steel (316) Cast Iron Air inlet (incl. ball valve): Air
More informationNDP-50 Specifications
NDP-50 Specifications Port Dimensions Intake & discharge connection: (164 GPM Max.) Polypropylene (PPG) 2" ANSI B16.5 #150 Kynar (PVDF) 2" ANSI B16.5 #150 Aluminum (ADC-12) 2" ANSI B16.5 #150 (with tapped
More informationVersa-Matic. Operating Manual. 3/8" Bolted Plastic Pumps. Polypropylene Kynar
Versa-Matic Operating Manual 3/8" Bolted Plastic Pumps Polypropylene Kynar E8 SAFETY WARNINGS Read these instructions completely before installation and start-up. It is the responsibility of the purchaser
More informationModel T15. DATA SHEET Specifications & Performance. Food Processing Metallic Design Level 1. Certified Quality
DATA SHEET Specifications & Performance Certified Quality Model T15 Food Processing Metallic Design Level 1 Quality System ISO91 Certified Environmental Management System ISO141 Certified Warren Rupp,
More informationModel G20. DATA SHEET Specifications & Performance. Metallic Design Level 1. Natural Gas-Operated Diaphragm Pumps.
DATA SHEET Specifications & Performance Certified Quality Model G20 Metallic Design Level 1 Natural Gas-Operated Diaphragm Pumps Quality System ISO9001 Certified Environmental Management System ISO14001
More informationModel HD20F. DATA SHEET Specifications & Performance. Non-Metallic Flap Valve Design Level 1. Certified Quality
DATA SHEET Specifications & Performance Certified Quality Model HD20F Non-Metallic Flap Valve Design Level 1 Quality System ISO 9001 Certified Environmental Management System ISO 14001 Certified Warren
More informationModel G1F. DATA SHEET Specifications & Performance. Metallic Design Level 1 Natural Gas-Operated Diaphragm Pumps.
DATA SHEET Specifications & Performance Certified Quality Model G1F Metallic Design Level 1 Natural Gas-Operated Diaphragm Pumps Quality System ISO9001 Certified Environmental Management System ISO14001
More information...your single dedicated resource for cost-effective mine pumping solutions. For Rugged Mining Duty
...your single dedicated resource for cost-effective mine pumping solutions For Rugged Mining Duty Mine Face Dewatering Fuel Transfer Sump Transfer Muck/Slimes/Slurry Drift Dewatering Drillers Mud Dewater
More informationModel W09 2" Non-Clog Wastewater Air-Operated Double Diaphragm Pump
SERVICE AND OPERATING MANUAL Model W09 2" Non-Clog Wastewater Air-Operated Double Diaphragm Pump CE Flap Valve Type 1 PLEASE NOTE! The photos shown in this manual are for general instruction only. Your
More informationSee pages 5 & 6 for ATEX ratings II 2GD T5. AIR VALVE No-lube, no-stall design 50(85) 60(101.9) 70(118.9) 80(135.9) 90(152.9) 100(169.
Quality System ISO9001 Certified Environmental Management System ISO14001 Certified II 2GD T5 See pages 5 & 6 for ATEX ratings Heavy Duty Flap Valve HDF2 Type 6 Air-Operated Double Diaphragm Pump ENGINEERING,
More informationHEAVY DUTY FLAP VALVE PUMPS For Fluids Containing up to Line Size Solids
HEAVY DUTY FLAP VALVE PUMPS For Fluids Containing up to Line Size Solids A WARREN RUPP, INC. BRAND SANDPIPERPUMP.COM KEY ADVANTAGES OF SANDPIPER FLAP VALVE PUMPS AN IDEAL SOLUTION FOR ABRASIVE SLURRIES,
More informationModels PB1 1 /2-A & PB2-A Type 3
SERVICE AND OPERATING MANUAL Models PB1 1 /2-A & PB2-A Type 3 PLEASE NOTE! The photos shown in this manual are for general instruction only. YOUR SPECIFIC MODEL MAY NOT BE SHOWN. Always refer to the parts
More informationWARREN RUPP, INC. A Unit of IDEX Corporation P.O. Box 1568 Mansfield, Ohio USA (419) Fax (419)
SERVICE AND OPERATING MANUAL Models EB1½ -SM Type 1 PLEASE NOTE! The photos shown in this manual are for general instruction only. Your specific model may not be shown. Always refer to the parts list and
More informationModel EB1-SM. Type 3 SERVICE AND OPERATING MANUAL
SERVICE AND OPERATING MANUAL Model EB1-SM Type 3 PRINCIPLE OF OPERATION This ball check valve pump is powered by compressed air and is a 1:1 pressure ratio design. It alternately pressurizes the inner
More informationModel SB1-A Model SB25A
SERVICE AND OPERATING MANUAL AL II 2GD b T5 CE Model SB1-A Model SB25A Type 4 PLEASE NOTE! The photos shown in this manual are for general instruction only. Your specific model may not be shown. Always
More informationU.S. Patent # 400,210; 5,996,627; 6,241,487
SERVICE & OPERATING MANUAL Model S15 Non-Metallic Design Level 2 Table of Contents Engineering Data and Temperature Limitations... 1 Explanation of Pump Nomenclature... 2 Performance Curve, Model S15 Non-Metallic
More informationModel S20 Non-Metallic Design Level 2
SERVICE & OPERATING MANUAL CE Model S20 Non-Metallic Design Level 2 Engineering Data and Temperature Limitations... 1 Explanation of Pump Nomenclature... 2 Performance Curve, Model S20 Non-Metallic Design
More informationWR10 3/8" Bolted Plastic Pumps Operating Instructions Polypropylene Kynar
WR10 3/8" Bolted Plastic Pumps Operating Instructions Polypropylene Kynar Warren Rupp, Inc. A Unit of IDEX Corporation 800 N. Main St., Mansfield, Ohio 44902 USA Telephone (419) 524-8388 Fax (419) 522-7867
More informationET Model Pumps Spill Containment Type 3
SERVICE AND OPERATING MANUAL ET Model Pumps Spill Containment Type 3 PLEASE NOTE! The photos shown in this manual are for general instruction only. Your specific model may not be shown. Always refer to
More informationModel PB 1 /2-A Type 3
SERVICE AND OPERATING MANUAL Model PB 1 /2-A Type 3 PLEASE NOTE! The photos in this manual are for general instruction only. Your specific model may not be shown. Always refer to the parts list and exploded
More informationSee pages 2, 7 and 8 for ATEX ratings. AIR VALVE No-lube, no-stall design 30(51) 35(00) U.S. Gallons per minute
Quality System ISO9001 Certified Environmental Management System ISO14001 Certified U1F Metallic Ball Valve Design Level 1 Air-Operated Double Diaphragm Pump See pages 2, 7 and 8 for ATEX ratings. ENGINEERING,
More informationWARREN RUPP, INC. A Unit of IDEX Corporation P.O. Box 1568 Mansfield, Ohio USA (419) Fax (419)
SERVICE AND OPERATING MANUAL Model PB¾ - A Type 3 PLEASE NOTE! The photos in this manual are for general instruction only. Your specific model may not be shown. Always refer to the parts list and exploded
More informationAODD PUMPS FOR YOUR MOST SEVERE APPLICATIONS
AODD PUMPS FOR YOUR MOST SEVERE APPLICATIONS HEAVY DUTY FLAP VALVE PUMP HEAVY DUTY BALL VALVE PUMP CONTAINMENT DUTY BALL VALVE PUMP ENSURES YOUR SUCCESS SANDPIPER Signature Series AODD pumps are engineered
More informationA200-2 INCH AIR OPERATED DOUBLE DIAPHRAGM PUMP
A200-2 INCH AIR OPERATED DOUBLE DIAPHRAGM PUMP A200 2 PUMP 2 ALUMINUM NPT or BSP Connections Zinc Plated Hardware Non-Metallic Muffler Suction Center Front / Discharge Center Rear Standard Porting SPECIFICATIONS
More informationSee pages 2, 7 and 8 for ATEX ratings. AIR VALVE No-lube, no-stall design
Quality System ISO9001 Certified Environmental Management System ISO14001 Certified S30 Metallic Design Level 1 Ball Valve Air-Operated Double Diaphragm Pump See pages 2, 7 and 8 for ATEX ratings. ENGINEERING,
More informationE8 Mini-Matic 3/8" Bolted Plastic Pumps Operating Instructions
E8 Mini-Matic 3/8" Bolted Plastic Pumps Operating Instructions Polypropylene SAFETY WARNINGS Read these instructions completely before installation and start-up. It is the responsibility of the purchaser
More informationSERVICE AND OPERATING MANUAL Model ST1-A Model ST25A. Type 4
II 2GD T5 CE SERVICE AND OPERATING MANUAL Model ST1-A Model ST25A Type 4 Principle of Operation This ball check valve pump is powered by compressed air and is a 1:1 pressure ratio design. It alternately
More informationA200-2 INCH AIR OPERATED DOUBLE DIAPHRAGM PUMP
A200-2 INCH AIR OPERATED DOUBLE DIAPHRAGM PUMP A200 2 PUMP 2 ALUMINUM NPT or BSP Connections Zinc Plated Hardware Non-Metallic Muffler Suction Center Front / Discharge Center Rear Standard Porting 2 STAINLESS
More informationModel SB1 1 /2-H Type 1
SERVICE AND OPERATING MANUAL Model SB1 1 /2-H Type 1 PLEASE NOTE! The photos shown in this manual are for general instruction only. Your specific model may not be shown. Always refer to the parts list
More informationAIR VALVE No-lube, no-stall design. SOLIDS-HANDLING Up to 1 / 32" (1mm) 6(10.2) U.S. Gallons per minute
Quality System ISO9001 Certified Environmental Management System ISO14001 Certified See pages 2, 13 and 14 for ATEX ratings. Model PB¼ Type 3 Air-Operated Double Diaphragm Pump Engineering, Performance
More informationSANDPIPER. Model S07 Non-Metallic. Design Level 1. Table of Contents SERVICE & OPERATING MANUAL. U.S. Patent # 400,210 5,996,627; 6,241,487
SERVICE & OPERATING MANUAL SANDPIPER A WARREN RUPP PUMP BRAND Model S07 Non-Metallic Design Level 1 U.S. Patent # 400,210 5,996,627; 6,241,487 CE Table of Contents Engineering Data and Temperature Limitations...
More informationE1 1" Bolted Plastic Pumps With Metallic Center Sections Operating Instructions
E1 1" Bolted Plastic Pumps With Metallic Center Sections Operating Instructions E1 Polypropylene E1 Kynar E1 1" Bolted Plastic Pump Optional Side Ports 8.06 [204.7] 1" ANSI 150# / DIN Fluid Discharge
More informationSANDPIPER. Model S05 Non-Metallic Design Level 2. Table of Contents SERVICE & OPERATING MANUAL
SERVICE & OPERATING MANUAL SANDPIPER A WARREN RUPP PUMP BRAND Model S05 Non-Metallic Design Level 2 Table of Contents U.S. Patent # 400,210; 5,996,627; 6,241,487 CE Engineering Data and Temperature Limitations...
More informationWarren Rupp, Inc. A Unit of IDEX Corporation P.O. Box 1568, Mansfield, Ohio USA Tel: (419) Fax (419)
SERVICE & OPERATING MANUAL Model S1F Non-Metallic Design Level 3 Table of Contents Engineering Data and Temperature Limitations... 1 Explanation of Pump Nomenclature... 2 Performance Curve, Model S1F Non-Metallic
More informationRedefining Performance
SAVE Energy SAVE Compressor Cost SAVE Operator Cost Redefining Performance Reduces air consumption up to 5% Adapts to process conditions Powered only by compressed air Saves energy while maintaining flow
More informationModel S05 Non-Metallic Design Level 1
SERVICE & OPERATING MANUAL Model S05 Non-Metallic Design Level 1 Table of Contents Engineering Data and Temperature Limitations... 1 Explanation of Pump Nomenclature... 2 Performance Curve... 3 Dimensions...
More informationModel SA1-A Model SA25A
SERVICE AND OPERATING MANUAL AL II 2GD b T5 CE Model SA1-A Model SA25A Type 4 PLEASE NOTE! The photos shown in this manual are for general instruction only. Your specific model may not be shown. Always
More informationSee pages 2, 6 & 7 II 2GD T5. for ATEX ratings. AIR VALVE No-lube, no-stall design 50(85) 60(101.9) 70(118.9) 80(135.9) 90(152.9) 100(169.
DRILLER S MUD SERIES Quality System ISO9001 Certified Environmental Management System ISO14001 Certified See pages 2, 6 & 7 II 2GD T5 for ATEX ratings 2" Flap Valve DMF2R & DMF2S Type 5 Air-Operated Double
More informationWARREN RUPP, INC. A Unit of IDEX Corporation P.O. Box 1568 Mansfield, Ohio USA (419) Fax (419)
A WARREN RUPP PUMP BRAND REPAIR PARTS LIST and DRAWING Model MP05D Design Level 1 ITEM NO. PART NUMBER DESCRIPTION TOTAL RQD. 1 095-051-551 Body, Spool Valve 1 2 031-083-000 Sleeve & Spool Set w/pins 1
More informationH/G-25 Series. Up to 20 gpm (75.7/min) H/G-25 Specialized Designs
H/G-25 Series Up to 2 gpm (75.7/min) H/G-25 Specialized Designs Hydra-Cell Slurry Duty pumps are specifically designed for abrasive slurry applications. See page 8 for complete specifications. The H-25
More informationPulsation Dampeners NEW! Wanner Engineering Inc
Pulsation Dampeners NEW! Wanner Engineering Inc Pulsation Dampeners Positive Displacement (PD) pumps create pulsation and hydraulic shock due to the reciprocating nature of their stroking action, potentially
More informationAIR VALVE No-lube, no-stall design 16 (27) 18 (30) U.S. Gallons per minute Liters per minute CAPACITY
Quality System ISO9001 Certified Environmental Management System ISO14001 Certified S05 Metallic Design Level 1 Ball Valve Air-Operated Double Diaphragm Pump For See ATEX page ratings 2 see for pages ATEX
More informationModel S30 Non-Metallic Design Level 2 Table of Contents
SERVICE & OPERATING MANUAL Original Instructions Model S30 Non-Metallic Design Level 2 Table of Contents Engineering Data and Temperature Limitations... 1 Explanation of Pump Nomenclature... 2 Performance
More informationAir Powered Double Diaphragm Pumps
Air Powered Double Diaphragm Pumps Notes. TC-X 030 Series Standard Diaphragm Pumps with 1/4" Connections Liquid Flow Rate: Maximum Air Inlet Pressure: Wetted Body Material Options; 1 to 8 L/min. (2.14
More informationST1 Type 5 ST25 Type 5
Quality System ISO9001 Certified Environmental Management System ISO14001 Certified Containment Duty ST1 Type 5 ST25 Type 5 Air-Operated Double Pump See pages 17 & 18 for ATEX ratings. ENGINEERING, PERFORMANCE
More informationModel HDB2-A Type 3. Table of Contents SERVICE AND OPERATING MANUAL
Table of Contents SERVICE AND OPERATING MANUAL I M2 c T5 II 2GD T5 CE Model HDB2-A Type 3 Principle of Operation... 1 Installation and Start-Up... 1 Air Supply... 1 Installation Guide... 2 Air Inlet &
More informationOUR SIGNATURE ENSURES YOUR SUCCESS A WARREN RUPP, INC. BRAND SANDPIPERPUMP.COM
CONTAINMENT DUTY BALL VALVE PUMPS The only complete line of AODD pumps featuring superior fluid containment; protecting your people, environment, and pump. OUR SIGNATURE ENSURES YOUR SUCCESS A WARREN RUPP,
More informationModel S1F Non-Metallic Design Level 3
SERVICE & OPERATING MANUAL Model S1F Non-Metallic Design Level 3 Table of Contents CE U.S. Patent # 400,210 5,996,627 6,241,487 Engineering Data and Temperature Limitations... 1 Explanation of Pump Nomenclature...
More informationDP Series Specifications
DP Series Specifications DP-10 Port Dimensions Intake & discharge connection: Polypropylene (PPG) Aluminum (ADC-12) Stainless Steel (316) (6 GPM Max.) 3/8" Female NPT 3/8" Female NPT 3/8" Female NPT DP-15
More informationD 40 ALUMINIUM (CLAMPED)
www.tablapump.com A COMPLETE RANGE OF AIR DIAPHRAGM PUMPS CONGRATULATIONS ON PURCHASING YOUR NEW TABLA PUMP! IMPORTANT: Please read all the installation and safety information carefully before you start
More informationAluminum Dimensions: 7.32" W 9.49"H Net Wt.: 7.9 lbs. (3.6 kg) Shipping Wt.: 9.9 lbs. Stainless Steel
DP Series Specifications DP-10 Port Dimensions (6 GPM Max.) Intake & discharge connection: Polypropylene (PPG) 3/8" Female NPT Aluminum (ADC-12) 3/8" Female NPT Stainless Steel (316) 3/8" Female NPT DP-15
More informationModel SET1-A Sanitary Type 3
SERVICE AND OPERATING MANUAL Model SET1-A Sanitary Type 3 PLEASE NOTE! The photos shown in this manual are for general instruction only. Your specific model may not be shown. Always refer to the parts
More informationModel S15. DATA SHEET Specifications & Performance. Non-Metallic Design Level 3. Certified Quality
DATA SHEET Specifications & Performance Certified Quality Model S15 n-metallic Design Level 3 Quality System ISO91 Certified Environmental Management System ISO141 Certified Warren Rupp, Inc. A Unit of
More informationProduct Engineering Guide
PRIMARY FLUID SYSTEMS INC. 1050 Cooke Blvd., Burlington, ON. Canada, L7T 4A8 Tel: (905)333-8743 Fax: (905)333-8746 Toll-Free: 1-800-776-6580 www.primaryfluid.com primary@primaryfluid.com Product Engineering
More informationModel SLUDGEMASTER SMA3-A
SERVICE AND OPERATING MANUAL Model SLUDGEMASTER SMA3-A OPERATING INSTRUCTIONS This pump has been tested prior to shipment from factory. The oil reservoir has been partially filled at testing with air motor
More information**Air Valve w/stroke Indicator Drawing and Parts List **Air Valve w/stroke Indicator Servicing **Solenoid Shifted Air Valve Drawing...
SERVICE & OPERATING MANUAL I M2 c/b T5 II 2GD b T5 Model S15 Metallic Design Level 1 Including T15 FDA A Compliant Models Table of Contents Engineering Data and Temperature Limitations... 1 Explanation
More informationG10 Series API bar (350 psi) for Non-metallic Pump Heads. G10 with Cast Iron pump head
G1 Series Maximum Flow Rate: Maximum Pressure: 33.4 l/min (8.8 gpm) 13 bar (15 psi) for Metallic Pump Heads 24 bar (35 psi) for Non-metallic Pump Heads API 674 ATEX G1 with Cast Iron pump head G1 with
More informationH/G-25 Series. Up to 20 gpm (75.7/min) H/g-25 hydra-cell diaphragm pump. H/G-25 Specialized Designs
H/g-25 hydra-cell diaphragm pump H/G-25 Series Up to 2 gpm (75.7/min) H/G-25 Specialized Designs Hydra-Cell Slurry Duty pumps are specifically designed for abrasive slurry applications. See page 8 for
More informationModel S1F Metallic Design Level 1 Including T1F FDA Compliant Models Table of Contents
SERVICE & OPERATING MANUAL Model S1F Metallic Design Level 1 Including T1F FDA Compliant Models Table of Contents Engineering Data and Temperature Limitations... 1 Explanation of Pump Nomenclature... 2
More information**Air Valve Drawing, Parts List, Service Instructions (Aluminum Centers Only) 16
SERVICE & OPERATING MANUAL SANDPIPER A WARREN RUPP PUMP BRAND Model S15 Metallic Design Level 1 Including T15 FDA Compliant Models Table of Contents Engineering Data and Temperature Limitations... 1 Explanation
More informationModel SMA3-A SLUDGEMASTER
SERVICE AND OPERATING MANUAL Model SMA3-A SLUDGEMASTER PLEASE NOTE! The photos shown in this manual are for general instruction only. YOUR SPECIFIC MODEL MAY NOT BE SHOWN. Always refer to the parts list
More informationModel HDB1½-A Type 7 Model HDB40-A Type 7. Table of Contents SERVICE AND OPERATING MANUAL
Table of Contents SERVICE AND OPERATING MANUAL CE I M2 c T5 II 2GD T5 Model HDB1½-A Type 7 Model HDB40-A Type 7 Principle of Operation... 1 Installation and Start-Up... 1 Air Supply... 1 Installation Guide...
More informationModel SB1-A/SB25A. Table of Contents SERVICE AND OPERATING MANUAL
Table of Contents SERVICE AND OPERATING MANUAL Model SB1-A/SB25A II 2GD T5 CE Type 4 Principle of Operation... 1 Installation and Start-Up... 1 Air Supply... 1 Installation Guide... 2 Air Inlet & Priming...
More informationModel S30 Non-Metallic Design Level 2 Table of Contents
SERVICE & OPERATING MANUAL Original Instructions Model S30 Non-Metallic Design Level 2 Table of Contents Engineering Data and Temperature Limitations... 1 Explanation of Pump Nomenclature... 2 Performance
More informationModel ST1½-A Type 4 Model ST40-A Type 4
I M2 c T5 II 2GD T5 SERVICE AND OPERATING MANUAL CE Model ST1½-A Type 4 Model ST40-A Type 4 PLEASE NOTE! The photos shown in this manual are for general instruction only. Your specific model may not be
More informationD/G-10 Series. Up to 8 gpm (30.3 l/min) D/g-10 hydra-cell diaphragm pump. D/G-10 Specialized Designs
D/g-1 hydra-cell diaphragm pump D/G-1 Series Up to 8 gpm (3.3 l/min) D/G-1 Specialized Designs Hydra-Cell Slurry Duty pumps are specifically designed for abrasive slurry applications. See page 8 for complete
More informationAIR VALVE No-lube, no-stall design. SOLIDS-HANDLING Up to.71 in. (18mm)
B75 Non-Metallic Design Level 2 Ball Valve Air-Powered Double-Diaphragm Pump Air Exhaust Side View Air Inlet Side View ENGINEERING, PERFORMANCE & CONSTRUCTION DATA INTAKE/DISCHARGE PIPE SIZE 3" ANSI Flange
More informationVersa-Matic SOLUTIONS. Experience Superior Performance. Multiple Porting Options. Shoe Valve Technology. Adaptable Footprint
Versa-Matic SOLUTIONS /2 (.mm) metallic and non-metallic bolted Experience Superior Multiple Porting Options Top, side and end porting for both inlet and discharge Shoe Valve Technology On / Off / On reliability,
More informationModels HDF3-A Type 7 HDF4-A Type 3. Table of Contents SERVICE AND OPERATING MANUAL
SERVICE AND OPERATING MANUAL II 2GD T5 CE Models HDF3-A Type 7 HDF4-A Type 3 Table of Contents Principle of Operation... 1 Installation and Start-Up... 1 Air Supply... 1 Air Inlet & Priming... 1 ESADS+Plus
More informationModel MSA3, MSA3-C Type 7 Mine/Construction-Duty. Table of Contents SERVICE AND OPERATING MANUAL
Table of Contents SERVICE AND OPERATING MANUAL II 2GD T5 CE Model MSA3, MSA3-C Type 7 Mine/Construction-Duty Principle of Operation... 1 Installation and Start-Up... 1 Air Supply... 1 Air Inlet & Priming...
More informationINSTRUCTION MANUAL AD SERIES PULSATION DAMPENERS
Form No. MAD021 INSTRUCTION MANUAL AD SERIES PULSATION DAMPENERS To insure safety, be sure to carefully read instruction manual prior to operation. Keep instruction manual in a easily accessible location.
More informationModel S10 Non-Metallic Design Level 1
SERVICE & OPERATING MANUAL Model S10 Non-Metallic Design Level 1 Table of Contents Engineering Data and Temperature Limitations...1 Explanation of Pump Nomenclature...2 Performance Curve...3 Dimensions:
More informationD 25 POLYPROPYLENE (BOLTED)
www.tablapump.com A COMPLETE RANGE OF AIR DIAPHRAGM PUMPS CONGRATULATIONS ON PURCHASING YOUR NEW TABLA PUMP! IMPORTANT: Please read all the installation and safety information carefully before you start
More informationModel S30 Non-Metallic Design Level 2 Table of Contents
SERVICE & OPERATING MANUAL Original Instructions Model S30 Non-Metallic Design Level 2 Table of Contents Engineering Data and Temperature Limitations... 1 Explanation of Pump Nomenclature... 2 Performance
More informationHusky 515 / 716 Air-Operated Diaphragm Pumps
First choice when quality counts. Husky 515 / 716 Air-Operated Diaphragm Pumps 515 1/2 in. non-metallic pumps in acetal, polypropylene, and kynar 716 3/4 in. metal pumps in SST, aluminum No seals to leak
More informationModel S05 Metallic Design Level 1
SERVICE & OPERATING MANUAL Model S05 Metallic Design Level 1 U.S. Patent # 5,996,627 & 6,241,487 Other U.S. Patents Applied for CE II 2GD b T5 Table of Contents Engineering Data and Temperature Limitations...
More informationAIR OPERATED DIAPHRAGM PUMPS
AIR OPERATED DIAPHRAGM PUMPS BULLETIN P-605 R JAN. 05 PUMP ANYTHING THAT CAN POUR SAFELY AND RELIABLY Wide selection of materials: SS - 36 stainless steel AL - Aluminum NSS - Conductive nylon ¼" - 2" sizes
More informationG25 Series API bar (350 psi) for Non-metallic Pump Heads. G25 with Cast Iron pump head
G25 Series Maximum Flow Rate: Maximum Pressure: 76 l/min (20.0 gpm) 69 bar (1000 psi) for Metallic Pump Heads 24 bar (350 psi) for Non-metallic Pump Heads API 674 ATEX G25 with Cast Iron pump head G25
More informationEPC DATA SUBMITTAL PACK. Customizable Pump Data Sheet for RFQ (with limited scope of supply) Specifications and Performance Data Sheet
EPC DATA SUBMITTAL PACK Customizable Pump Data Sheet for RFQ (with limited scope of supply) Specifications and Performance Data Sheet GODD_EPC_Pump_Data_Sheet (v2.3).xlsx Page 1 Requester's LOGO NATURAL
More informationModels HDB3-A/HDB4-A. Table of Contents. Type 3 SERVICE AND OPERATING MANUAL
SERVICE AND OPERATING MANUAL I M2 c T5 II 2GD T5 Models HDB3-A/HDB4-A CE Type 3 Table of Contents Installation Guide... 1 Principle of Operation... 2 Installation and Start-Up... 2 Air Supply... 2 Air
More informationPUMPS Bulk Chemical Transfer Resins Transfer Wastewater Treatment Food Processing Filter Press Applications Tanker Car Unloading
olted Plastic olted Metallic lamped Metallic E3 TREE IN PUMPS ulk hemical Transfer Resins Transfer Wastewater Treatment Food Processing Filter Press Applications Tanker ar Unloading When you need to pump
More informationD/G-35 Series. Up to 37gpm (140 l/min) D/g-35 hydra-cell diaphragm pump. D/G-35 Specialized Designs
D/g-35 hydra-cell diaphragm pump D/G-35 Series Up to 37gpm (14 l/min) D/G-35 Specialized Designs Hydra-Cell Slurry Duty pumps are specifically designed for abrasive slurry applications. See page 8 for
More informationAir Powered Double Diaphragm Pumps. Polypropylene Pumps. Made In Japan
Air Powered Double Diaphragm Pumps Polypropylene Pumps Made In Japan Presenting YTS Double Diaphragm Pumps Made In Japan Fully Non-Lubricated Design High Flow Rates Efficient Air Consumption Easy & Fast
More informationII 2G c T5 II 2 D c T100 C
SERVICE AND OPERATING MANUAL II 2G c T5 II 2 D c T100 C Model EH2-M & SH2-M HIGH PRESSURE DUTY Type 4 PRINCIPLE OF OPERATION This pump is a 2:1 pressure ratio single acting pump powered by compressed air.
More informationII 2GD T5. U.S. Patent #5,996,627 & 6,241,487 Other U.S. Patents Applied for. AIR VALVE No-lube, no-stall design
Quality System ISO91 Certified Environmental Management System ISO141 Certified CE II 2GD T5 S2 Non-Metallic Design Level 3 Ball Valve Air-Operated Double Diaphragm Pump U.S. Patent #5,996,627 & 6,241,487
More informationOPERATION MANUAL. ALUMINUM Models. 316 S.S. Models NTG40 NOMAD TRANS-FLO AIR-OPERATED DOUBLE DIAPHRAGM PUMPS. A JDA Global Company. 1/14, Rev.
OPERATION MANUAL NTG40 NOMAD TRANS-FLO AIR-OPERATED DOUBLE DIAPHRAGM PUMPS ALUMINUM Models 316 S.S. Models A JDA Global Company 1/14, Rev. 3 CAUTION SAFETY POINTS TEMPERATURE LIMITS: Neoprene -17.8 C to
More informationG10 Series API bar (350 psi) for Non-metallic Pump Heads. G10 with Cast Iron pump head
G10 Series Maximum Flow Rate: Maximum Pressure: 33.4 l/min (8.8 gpm) 103 bar (1500 psi) for Metallic Pump Heads 24 bar (350 psi) for Non-metallic Pump Heads API 674 ATEX G10 with Cast Iron pump head G10
More informationModel S05 Non-Metallic Design Level 2
SERVICE & OPERATING MANUAL Model S05 Non-Metallic Design Level 2 Table of Contents Engineering Data and Temperature Limitations...1 Explanation of Pump Nomenclature...2 Performance Curve...3 Dimensions...4
More informationSHOCK BLOCKER FLUID PULSATION DAMPENERS
SHOCK BLOCKER FLUID PULSATION DAMPENERS The Automatic Shock Blockers For over 85 years, the ARO Fluid Products business of Ingersoll Rand has developed partnerships with more than 200 original equipment
More informationD/G-12 Series. Up to 8 gpm (30.3 l/min)
D/G-12 Series Up to 8 gpm (3.3 l/min) D/G-12 Vertical Applications The D/G-12 is specifically designed for vertical pumping installations such as machine tool cooling applications. D/G-12 shown with Hydra-Cell
More information103 bar (1500 psi) for Metallic Pump Heads
G35 Series Maximum Flow Rate: Maximum Pressure: 138 l/min (36.5 gpm) 13 bar (15 psi) for Metallic Pump Heads API 674 ATEX G35 with Stainless Steel pump head and SAE flanges G35 with Brass pump head G35
More informationModel S20 Metallic Design Level 1
SERVICE & OPERATING MANUAL Model S20 Metallic Design Level 1 Table of Contents Engineering Data and Temperature Limitations... 1 Explanation of Pump Nomenclature... 2 Performance Curve... 3 Dimensions...
More informationHydracel High Pressure Pump
Hydracel High Pressure Pump Mfg: Hydracell Model: D10 SL SE SHEHC Stock No. HDPH038.5a Serial No. 99260 Hydracell High pressure Pump. Model D10 SL SE SHEHC, S/N 99260. Inlet (1) 1-1/2 in., Outlet (1) 1
More informationModel S30. SERVICE & OPERATING MANUAL Original Instructions. Metallic Design Level 1. Certified Quality 1: PUMP SPECS 2: INSTAL & OP 3: EXP VIEW
SERVICE & OPERATING MANUAL Original Instructions Certified Quality Model S30 Metallic Design Level 1 1: PUMP SPECS OPTIMIZED PERFORMANCE ISO 9001 Certified ISO 14001 Certified 5: WET END 4: AIR END 2:
More informationA measured step forward
A measured step forward Operations & Maintenance Manual TM AODD 1/2 Air Operated Double Diaphragm Pump 2 Phone: (585) 426-0990 www.lutzjescoamerica.com Fax: (585) 426-4025 Contents Cautions Read First!...4
More information