Wiring Accessories. Selection of Styles

Transcription

1 Wiring Accessories Courtesy of Steven Engineering, Inc. 230 Ryan Way, South San Francisco, CA, Main Office: (650) Outside Local Area: (800) Wiring Accessories are an integral part of Panduit s comprehensive selection of wire management products. These accessories help provide you with the lowest installed solution to controlling, mounting and protecting wire and cable. These products are manufactured in an environment committed to design innovation, high quality and knowledgeable service to our customers. The key benefits of this commitment are: The highest quality manufacturing environment, including statistical process control to meet applicable international and domestic standards Contact the factory for registrar and product scope information. Selection of Styles PANDUIT teams up with a national network of Distributors to provide you with Just In Time shipping to eliminate your need for large inventories Fully staffed engineering and tool & die departments to assist in designing solutions to specific industry applications Continuous research on materials, adhesives and new technologies to provide you the latest product innovations Tie Accessories These products are used with PANDUIT Ties to speed and simplify the mounting of wires, cables and tubing. Installation methods include self-adhesive-backed, user applied adhesive, screws, rivets or through-panel mount designs. Wiring Accessories These productsincluding fixed and adjustable diameter accessoriesare used without cable ties. methods include self-adhesive-backed, user applied adhesive, screws, rivets or through-panel designs. Harness Board Accessories Panduit s unique selection of harness board accessories speeds the routing and forming of wire in harness fabrication. They hold wires at a uniform height above the board and are ideal for use with PANDUIT manual and automatic cable tie tooling. Abrasion Protection Products Spiral wrapping, braided expandable sleeving and corrugated tubing enclose wires, hoses and tubing to protect them from abrasion. They are available in a variety of sizes and materials to meet a broad range of indoor and outdoor applications. Grommet edging provides abrasion protection on outside edges and holes cut through metal or plastic surfaces. 79

2 Tie Accessories Courtesy of Steven Engineering, Inc. 230 Ryan Way, South San Francisco, CA, Main Office: (650) Outside Local Area: (800) Combination Adhesive Mount/ Tie Locking PLA2S-A-Q Releasable PRA2S-A-Q Length A In. (mm) 7.3 (185) 7.3 (185) Adhesive mount and cable tie molded as one piece help reduce inventory costs. Mount portion features ramp to guide tip into tie head and holes to install two (2) optional #6 screws for added mounting strength. Available with locking or releasable tie. Extended adhesive liner release tab on mount for fast liner removal. Tie Specifications Width B In. (mm).19 (4.8).19 (4.8) ABM1M-A-C M ABM1M-AT-C M ABMM-A-C M,I ABMM-AT-C M,I ABMM-AT-C0 M,I Max. Bundle Dia. In. (mm) 1.85 (47) 1.85 (47) 4-Way Adhesive Backed Mounts Min. Loop Tensile Strength Lbs. (N) 50 lbs. (222N) 50 lbs. (222N) Recommended PANDUIT Installation Tool GS2B, GS4H, PPTS, STS2 or STH2 Hand Installed Only Mount Static Load.45 lbs. (204g).45 lbs. (204g) Lower your installed costs with fast, easy-to-install PANDUIT adhesive-backed cable tie mounts. Four-way tie entry for easy orientation of wires or cables. For specific information on adhesive properties and technical data on mount selection, see Pages 115 to 120. ABMM-A ABMM-AT PANDUIT mounts are produced either 2-up or 4-up for fast and easy liner removal to speed installation. ABM1M-A and ABM1M-AT mounts are supplied on a dispenser strip of four mounts. ABMM-A and ABMM-AT mounts are supplied on a dispenser strip of two mounts..16 (4.0).16 (4.0).18 (4.6).18 (4.6).18 (4.6) ABM1M-A ABM1M-AT Adhesive Type/Static Load lbs. (g) White Rubber.13 (59) White / Acrylic.13 (59) ABS White Rubber.30 (136) ABS White / ABS Outdoors/ Acrylic.30 (136) Acrylic.30 (136) 80 Part Numbers listed are for Standard s in Standard Package Quantity. For Package Part Numbers, see Pages 128 & ** Tie Cross Section Sizes: M = Miniature, I = Intermediate, S = Standard, LH = Light Heavy and H = Heavy.

3 4-Way Adhesive Backed Mounts ABM2S-A-C M, I, S ABM2S-A-C14 M, I, S ABM2S-A-C15 M, I, S ABM2S-AT-C M, I, S ABM2S-AT-C0 M, I, S ABM3H-A-L M, I, S, ABM3H-AT-L M, I, S, ABM4H-A-L M, I, S, ABM4H-AT-L M, I, S, ABM100-A-C M, I, S ABM100-A-C14 M, I, S ABM100-A-C15 M, I, S ABM100-AT-C0 M, I, S 4-Way Mounts out Adhesive ABMM-D M, I ABM2S-S6-D M, I, S ABM3H-S6-T M, I, S, ABM4H-S6-T M, I, S, ABM2S For greater support use two (2) screws in mounting holes. Supplied two mounts on a dispenser strip (6.1).24 (6.1).24 (6.1).24 (6.1) 2.00 ABM100-S6-C M, I, S ABM100-S6-C69 M, I, S Adhesive Backed Tie Mounts (3.6).16 (4.0).21 (5.3).21 (5.3) Adhesive Type/Static Load lbs. (g) ABS White Rubber (227) ABS Gray Rubber (227) ABS Ivory Rubber (227) ABS White / ABS Outdoors/ Acrylic (227) Acrylic (227) White Rubber 1.12 (508) White / Acrylic 1.12 (508) White Rubber 2.0 (907) White / Acrylic 2.0 (907) White Rubber (227) Gray Rubber (227) Ivory Rubber (227) Outdoors/ Acrylic (227) ABS White User supplied adhesive ABS White User supplied White adhesive and/or (2) #S6 s White White User supplied adhesive and/or Flame Retard. ABM3H ABM4H For greater support use two (2) screws in mounting holes. ABM100 For greater support use one (1) screw in mounting hole. Supplied two mounts on a dispenser strip. Except ABM100-S6-C Cream (1) #S Part Numbers listed are for Standard s in Standard Package Quantity. For Package Part Numbers, see Pages 128 & ** Tie Cross Section Sizes: M = Miniature, I = Intermediate, S = Standard, LH = Light Heavy and H = Heavy. 81

4 2-Way Mounts Adhesive-Backed ABMS-A-C M, I, S 1.13 (28.7) ABMS-AT-C M, I, S 1.13 (28.7) Mounted ABMS-S6-D M, I, S 1.13 (28.7) ties may be inserted from either of two sides. Choose adhesive backed or screw installed mounts (28.7) 1.13 (28.7) 1.13 (28.7) Snap-In Tie Mount Adhesive Backed SMS-A-C S 2.00 SMS-A-C14 SMS-A-C15 S 2.00 Mounted SMS-S6-D S 2.00 SMS-S6-D15 S 2.00 Adhesive Backed Tie Mounts Recommended cable ties: PLT1S, PLT1.5S, PLT2S, PPRT1.5S, PRT2S. Tie colors available to match SMS mounts..25 (6.1).25 (6.1).21 (5.3).35 (8.9).35 (8.9).31 (7.9).31 (7.9) Use one (1) #6 screw with ABMS-S6. For added support with adhesive backed mounts, use one (1) screw or 1/4" flat head rivets. ABMS-A mounts are supplied two mounts to a dispenser strip. Rubber Tape / high. Temp. Acrylic Tape Size Mount Integral retaining notch holds cable tie head in place below bundle; eliminates protruding tie head and facilitates one hand tie threading. SMS-A Adhesive backed SMS-S applied ABS White Rubber Based ABS Gray Foam Ivory Tape Size ABS White (2) S (M3) ABS Ivory Part Numbers listed are for Standard s in Standard Package Quantity. For Package Part Numbers, see Pages 128 & ** Tie Cross Section Sizes: M = Miniature, I = Intermediate, S = Standard, LH = Light Heavy and H = Heavy.

5 Epoxy Applied Mounts These mounts are designed for application with PANDUIT EMA Epoxy. Provides fast, strong, economical method to secure wire or cable to steel, aluminum, glass, wood and most other surfaces. Especially well suited to construction and maintenance applications where they eliminate the need to drill into surfaces. EMS-A-C M, I, S EMS-A-C0 M, I, S Max. Static Load lbs. (g) (4540) (6.6) EMA.26 Weather Outdoors Epoxy (6.6) 10 (4540) Blk. Max. static load rating, following full cure period, when applied with PANDUIT EMA Epoxy Adhesive according to installation instructions. Epoxy Applied Swivel Mount ASMS-A-X M, I, S (28.6) Mount swivels 360 to assure proper orientation with harness. Four inspection holes to check adhesive coverage. Base and Rivet: Aluminum; Mount: (28.6).35 (8.9) Aluminum Base / Outdoors EMA Epoxy Epoxy Adhesive and Mount Kits EMA Epoxy supplied in convenient two-compartment mixer cup with a mixer stick for each cup. Each cup contains adhesive for three (3) EMA or ASMS mounts. Epoxy hardens in about five (5) minutes. Supports about 5 lbs. after first 15 minutes. After full 24 hour EMSK3-1-X0 Epoxy Kit with mounts. Packed in sturdy foil pouch EMSK X0 Epoxy Kit with mounts and cable ties Epoxy Applied Mounts curing time, bonding strength will exceed 50 lbs. on clean, grease-free surface. Part Number Epoxy Adhesive only EMA-X Indoor/ Outdoor Epoxy Kit with EMA Mounts EMSK3-1-X0 M, I, S Indoor/ Outdoor Epoxy Cups 10 (4540) Contents of Each Kit Mixer Sticks EMS Mounts EMA EPOXY Ties None None 10 Kits None 10 Kits Epoxy Kit with EMA Mounts and Ties EMSK M, I, S ea. EMSK X0 M, I, S Indoor/ Outdoor PLT2S-0 12 ea. PLT2S-0 Part Numbers listed are for Standard s in Standard Package Quantity. For Package Part Numbers, see Pages 128 & 129. ** Tie Cross Section Sizes: M = Miniature, I = Intermediate, S = Standard, LH = Light Heavy and H = Heavy. 1 Kit 10 Kits 100 Kits 10 Kits 100 Kits 83

6 Tie Mounts Mechanically Applied Unique cradle design provides maximum stability and rigidity to the wire bundle. or rivet installed. TM1S4-C M.513 (13.0) TM1S6-C M.513 (13.0) TM1S4-M30 M.513 (13.0) TM1S4-M69 M.513 (13.0) TM2S6-C M, I, S.630 (16.0) TM2S8-C M, I, S.630 (16.0) TM2R-C M, I, S.630 (16.0) TM2R6-M0 M, I, S.630 (16.0) TM2S8-C100 M, I, S.585 (14.9) TM2S8-M120 M, I, S.630 (16.0) TM3S8-C M, I, S, LH.875 (22.2) TM3S10-C M, I, S, LH.875 (22.2) TM3S25-C M, I, S, LH.875 (22.2) TM3R6-C M, I, S, LH.875 (2.2) TM3S8-C69 M, I, S, LH.875 (22.2) TM3S8-C76 M, I, S, LH.875 (22.2) TM3S10-C76 M, I, S, LH.875 (22.2) TM3S8-C100 M, I, S, LH.875 (22.2) TM3S8-C702 M, I, S, LH.875 (22.2) Part Number TM1S4 TM1S6 TM2S6 TM2S8 TM2R6 TM3S8 TM3S10 TM3S25 TM3R6 Hole Diameter Inches (mm) Hole Dia..120 (3.0).150 (3.8).150 (3.8).180 (4.6).190 (4.8).180 (4.6) (6.6).190 (4.8) Tie Mounts Counterbore Dia..230 (5.8).280 (7.1).280 (7.1).320 (8.1) Countersunk.320 (8.1).390 (9.9).510 (12.9) Countersunk.316 (8.0).316 (8.0).316 (8.0).316 (8.0).425 (10.8).425 (10.8).425 (10.8).425 (10.8).425 (10.8).620 (15.8).620 (15.8).620 (15.8).620 (15.8).620 (15.8).620 (15.8).620 (15.8).620 (15.8).620 (15.8).230 (5.8).230 (5.8).230 (5.8) Heat.230 (5.8).275 (7.0).275 (7.0).275 (7.0).275 (7.0).275 (7.0).275 (7.0) Heat Stabilized TM1S6-M30 TMSR6-M30 TM2S6-M30 TM2S8-M30 TM3R6-M30 TM3S8-M30 TM3S10-M30 TM3S25-M30 Stabilized Weather- Weather Polypropylene #4 (M2.5) #4 (M2.5) Ivory #4 (M2.5) #8 (M4) Rivet Countersunk Outdoors Rivet Countersunk Except TM1S4-M69 TM2S8-C100 TM2S8-M120 TM3S8-C69 TM3S8-C100 TM3S8-C Outdoors #8 (M4) 12 Outdoors #8 (M4) 1000 #8 (M4) Flame Retardant 1/4" (M6) Rivet Countersunk Ivory #8 (M4) TEFZEL Aqua #8 (M4) TEFZEL Aqua Weather Polypropylene Outdoors #8 (M4) HALAR Maroon / Outdoors #8 (M4) Additional Tie Mount Part Numbers Available in specified materials. All are available as standard PANDUIT parts Flame Retardant TM1S6-M69 TM2S6-M69 TM2S8-M69 TM3S8-C69 TM3S8-M69 Weather- TM1S6-M0 TM2R6-M0 TM2S6-M0 TM2S8-M0 TM3R6-M0 TM3S10-Q0 TM3S10-M0 TM3S25-M Weather- Polypropylene TEFZEL 12 TM2S8-M100 TM3S8-C100 TM3S8-M100 TM3S10-C76 TM3S8-M TEFZEL is the Registered Trademark of E. I. Dupont Co., fluoropolymer HALAR is the Registered Trademark for Ausimont, Inc. fluoropolymer Part Numbers listed are for Standard s in Standard Package Quantity. For Package Part Numbers, see Pages 128 & ** Tie Cross Section Sizes: M = Miniature, I = Intermediate, S = Standard, LH = Light Heavy and H = Heavy.

7 Tie Mounts Courtesy of Steven Engineering, Inc. 230 Ryan Way, South San Francisco, CA, Main Office: (650) Outside Local Area: (800) Extra Heavy Tie Mounts TMEH-S8-Q0 EH 1.65 (42) TMEH-S10-Q0 EH 1.65 (42) TMEH-S25-Q0 EH 1.65 (42) TMEH-S10-C100 EH 1.65 (42) TMEH-S10-C109 EH 1.65 (42) Stud Tie Mounts TMSTLHS Type TMSTLHS6-C0 M, I, S, LH 1.25 (31.8) TMSTLHS8-C0 M, I, S, LH 1.25 (31.8) TMSTHS13-C0 M, I, S, TMSTHS16-C0 M, I, S, TMSTHS19-C0 M, I, S,.74 (19).74 (19).74 (19).74 (19).74 (19).61 (15).61 (15).61 (15).61 (15).61 (15) Mounts designed specially for use with PANDUIT Extra Heavy cross-section lashing ties for mounting cable, large wire bundles or tubular shapes. Weather- Weather- Polypropylene Polypropylene Green Except TMEH-S10-C100 TMEH-S10-C109 Outdoors #8 (M4) Outdoors Outdoors 1/4" (M6) Outdoors Easily applied to bolts or studs with a light hammer blow or turning of the mount. The mounts are designed for use with cable ties to mount wire bundles, air, water and hydraulic lines (50.6) 1.99 (50.6) 1.99 (50.6) 0.48 (12.2) 0.48 (12.2) 1.01 (25.6) 1.01 (25.6) 1.01 (25.6) TMSTHS Type 0.95 (24.1) 0.95 (24.1) 1.10 (27.9) 1.10 (27.9) 1.10 (27.9) Weather Part Number TMEHS8 TMEHS10 TMEH25 Outdoors 1/4" Stud Dia. (6M) 5/16" Stud Dia. (8M) 1/2" Stud Dia. (13M) 5/8" Stud Dia. (16M) 3/4" Stud Dia. (19M) Hole Diameter.18" (4.3 mm).20" (5.1 mm).26" (6.6 mm) Counterbore Diameter.51" (13.0).51" (13.0).51" (13.0) Part Numbers listed are for Standard s in Standard Package Quantity. For Package Part Numbers, see Pages 128 & 129. ** Tie Cross Section Sizes: M = Miniature, I = Intermediate, S = Standard, LH = Light Heavy, H = Heavy and EH = Extra Heavy. 85

8 AM2-C M, I, S 1.24 (31.5) Tie Mounts Tie Mounts Applied with User Supplied Adhesives Apply cyanoacrylic or another type adhesive to mount surface. Any adhesive selected should be user-tested to assure suitability for the actual application. Mounts should be installed on a clean, dry and grease-free surface. Bond strength depends on adhesive used. Low Profile Mount - AM2 TM1A, TM2A, TM3A TM1A-C M.512 (13.0) TM2A-C M, I, S.830 (16.0) TM3A-C M, I, S, H.875 (22.2) Low profile design keeps bundle close to mounting surface where overhead space is limited. Inches (mm) 1.24 (31.5).125 Cyanoacrylic Adhesive Solid flat bottom surface provides maximum holding area..325 (8.0).425 (10.8).625 (15.9).230 (5.8).270 (6.9).380 (9.7) Cyanoacrylic Adhesive 86 Part Numbers listed are for Standard s in Standard Package Quantity. For Package Part Numbers, see Pages 128 & ** Tie Cross Section Sizes: M = Miniature, I = Intermediate, S = Standard, LH = Light Heavy and H = Heavy.

9 Tie Anchor Mounts TA1 Anchor TA1S8-C M, I, S TA1S10-C M, I, S TA1S8-M30 M, I, S TA1S8-M69 M, I, S TA2 Anchor D Low profile and versatile, these screw-installed mounts can be ideal for applications where space is limited. Designed for four-way cable tie insertion, this mount can be mounted in-line or perpendicular to the wire bundle..195 (5.0).195 (5.0).195 (5.0).195 (5.0).170 (4.3) (4.3).170 (4.3) Heat Sta. Flame Ret. TA1S8 is also available in: Heat-stabilized : TA18-M30 Flame-resistant : TA1S8-M69 Weather-resistant : TA1S8-M0 TA1S10 is also available in: Weather-resistant : TA1S10-M0 #8 (M4) #8 (M4) Ivory #8 (M4) This mount is installed perpendicular to the wire bundle. Elongated slot permits installing the screw and aligning mount with the bundle attached. TA2-C M, I, S See Drawing Low Profile Mounts Applied Low Profile Mounts LPMM-S2-C M.40 (10.2) LPMM-S5-C M.40 (10.2) LPMS-S8-C M, I, S Knock-In Low Profile Mounts KIMS-H366-C2 M, I, S.155 (3.9) KIMS-H430-C6 M, I, S.180 (4.6) KIMS-H500-C4 M, I, S.202 Tie Mounts.32 (8.1).32 (8.1) Except TA1S8- M69 Designed to secure wire bundles where space is limited..10 (2.5).10 (2.5).12 (3.0) LPMM (2.4) (3.5) (4.6) See Drawing.144 (3.7) See Drawing.169 (4.3) See Drawing.196 (5.0) 1 Combination Counter Bore & Counter Sunk Hole (.088" (2.2) Dia. Rivet can also be used) 2 Counter Sunk LPMS Red Integral Push Rivet Blue Integral Push Rivet Yellow Integral Push Rivet #2 (M2) Flathead #5 (M3) Flathead #8 (M4) Flathead Secures wires to any pre-drilled panel. Can be installed in any panel thickness. Eliminates screws. Easy to Install 1. Push rivet in pre-drilled panel hole. 2. Use PANDUIT Rivet Installation Tool (TNR) or hammer to drive the pin flush to the base. This drives the rivet into the hole and secures the mount. 3. Attach wires to the mount with cable tie Part Numbers listed are for Standard s in Standard Package Quantity. For Package Part Numbers, see Pages 128 & 129. ** Tie Cross Section Sizes: M = Miniature, I = Intermediate, S = Standard, LH = Light Heavy and H = Heavy. 87

10 Tie Plates Part Number TP2-C M, I, S 1.98 (50.3) TP4H-C M, I, S, H 3.08 (78.2) Tie Plates applied. Each tie plate has a slotted mounting hole to accommodate various fastener spacings. D E F G.62 (15.7) Multiple Tie Plates MTP1S-E6-C MTP1S-E10-C MTP1H-E6-C MTP1H-E10-C MTP2S-E6-C MTP2S-E10-C MTP2H-E6-C MTP2H-E10-C MTP3S-E6-C MTP3S-E10-C MTP3H-E6-C MTP3H-E10-C MTP4S-E6-C MTP4S-E10-C MTP4H-E6-C MTP4H-E10-C MTP5S-E6-C MTP5S-E10-C MTP5H-E6-C MTP5H-E10-C MTP6H-E6-C MTP6H-E10-C No. of Bdls M, I, S 1 (44.5) M, I, S, H 2.09 (53.1) M, I, S 3.00 (76.2) M, I, S, H 3.59 (91.2) M, I, S 4.25 (108.0) M, I, S, H 5.09 (129.3) M, I, S 5 (139.7) M, I, S, H 6.59 (167.4) M, I, S 6 (171.5) M, I, S, H 8.09 (205.5) M, I, S, H 9.59 (243.6) (5.2) (6.9).40 (10.2).31 (7.9) (6.9) & 1.60 (40.6) 2 (63.5) Size /4" (M6) applied. to secure closely spaced wire bundles. & (3.7).30 (7.6) (3.7).30 (7.6) (3.7).30 (7.6) (3.7).30 (7.6).200 D E F.62 (15.7).62 (15.7).62 (15.7).62 (15.7).62 (15.7).62 (15.7) (5.2) (5.2) (5.2) (5.2) (5.2).203 (5.2) 1.25 (31.8) 1.25 (31.8) 1.25 (31.8) 1.25 (31.8) 1.25 (31.8) (3.7).30 (7.6) (3.7).30 (7.6) (3.7).30 (7.6) (3.7).30 (7.6) (3.7).30 (7.6) (3.7).30 (7.6) (3.7).30 (7.6).200 Mil. Part No. MS MS MS MS MS MS MS MS MS MS MS Size For use with most common screw types except flat head Part Numbers listed are for Standard s in Standard Package Quantity. For Package Part Numbers, see Pages 128 & Part Number shown for MTP parts is Package Quantity. ** Tie Cross Section Sizes: M = Miniature, I = Intermediate, S = Standard, LH = Light Heavy and H = Heavy.

11 Right Angle Mounts RAMS-S3-M M, I, S.56 (14.2) RAMH-S6-D M, I, S, H RAMH-S10-D M, I, S, H Secure wire bundles that run through bulkheads or cabinet holes, holding them away from sharp edges, thus eliminating the need for grommet protection. Can also be used to mount wire bundles adjacent to any surface. or rivet applied. D E F.39 (9.9) Lightening Hole Mounts LHMS-S5-D M, I, S.44 (11.2).095 (2.4) (1.5).18 (4.6).18 (4.6).281 (7.1) 0 0 & Mil. Part No. MS MS Size #3 (M2.5) or 3/32" (2.4) Round Head Rivet #6 (M3) or 1/8" Round Head Rivet #10 (M5) or 3/16" (4.7) Round Head Rivet to secure wire bundles which run through bulkhead lightening holes (.87" [22.1mm] dia. or larger) and keeps the bundles away from sharp edges. Only one screw, rivet, or self-tapping screw needed. D.127 LHMS-S6-D M, I, S.145 See Drawing (3.7) LHMS-S10-D M, I, S.192 (4.9) Tie Mounts See Drawing & Mil. Part No. Size #5 (M3) or 1/8" or Self-Tapping MS #6 (M3) or 9/64" (3.5) Rivet or #8 (M4) Self- Tapping #10 (M5) or 3/16" (4.7) Rivet Part Numbers listed are for Standard s in Standard Package Quantity. For Package Part Numbers, see Pages 128 & ** Tie Cross Section Sizes: M = Miniature, I = Intermediate, S = Standard, LH = Light Heavy and H = Heavy. 89

12 Tie Mounts Metal Clip-On Mount MCMS12-P-C M, I, S.88 (22) MCMS25-P-C M, I, S.88 (22) Metal Mount MBMS-S10-C M, I, S The mount clips on sheet metal edges for fast mounting of harnesses with cable ties. Ties may be inserted from any of the four sides for easy harness orientation. MCMS12-P-C Panel Thickness (.7-3.2) (14) (8) Zinc Plated Steel (14) (11.5) MIL C D Class 3 Coating Part Numbers listed for MCMS12-P are Package Quantity. MCMS25-P-C Panel Thickness ( ) Clip-On or Outdoors Clip-On applied aluminum mounting base for a secure support in demanding applications.130 (3.3) Aluminum (Chromate Coated) or Outdoors NOTE: Mount can also be installed with a user supplied adhesive. Max. Static Load lbs. (g) 10 (4540) Part Numbers listed for MBMS-S10 is Standard Package Quantity. For Package Part Numbers, see Pages 128 & ** Tie Cross Section Sizes: M = Miniature, I = Intermediate, S = Standard, LH = Light Heavy and H = Heavy.

13 Push Mounts Winged Push Mounts Push mounts require no adhesive backing or additional mounting hardware. They are inserted into pre-drilled holes. The winged base applies pressure on the panel wall to provide a more secure mount in high vibration applications. Can be used where only one side of the panel is accessible. Panel Thickness Max. Hole Diameter PWMS-H25-C M, I, S PWMS-H25-M0 M, I, S (2.7) Weather- Outdoors 1000 Inserted See Drawing into predrilled hole TM2PWH25-C M, I, S.094 (2.3) Push Mount This part is a version of the mount shown above, but without the tensioning wings. PM2H25-C M, I, S.250 Panel Thickness Max..125 PM2H25-M0 M, I, S,.125 See Drawing PM2H25-M30 M, I, S.125 Tie Mounts Push Button Mount Designed for use where both sides of the panel are accessible. PWMS-H25 Hole Diameter Weather- Heat Stabilized TM2PWH25 Outdoors Inserted into predrilled hole Panel Thickness Max. Hole Diameter PBMS-H25-C PBMS-H25-C14 Gray PBMS-H25-M0 Weather- Outdoors Inserted M, I, S See Drawing into predrilled hole PBMS-H25-M30 Heat Stabilized 1000 Part Number shown for PWMS-H25-C, TM2PWH25-C, PM2H25-C, PBMS-H25-C and PBMS-H25-C14 are for Standard Package Quantity. For Package Part Numbers, see Pages 128 & 129. Part Numbers listed for MCMS12-P are Package Quantity. ** Tie Cross Section Sizes: M = Miniature, I = Intermediate, S = Standard, LH = Light Heavy and H = Heavy. 91

14 Tie Mounts Courtesy of Steven Engineering, Inc. 230 Ryan Way, South San Francisco, CA, Main Office: (650) Outside Local Area: (800) Masonry Push Mounts to secure wire, cable or tubing to masonry surfaces. Installed quickly into pre-drilled holes. Design holds bundle securely. MPMS19, MPMS25, MPMH38 & MPMWH32 1. Drill hole using correct size bit. 2. Hammer mount into hole. 3. Place cable tie through mount. 4. Install wires or cable. MPMS19-C0 M, I, S.97 (24.6) MPMS25-C0 M, I, S.97 (24.6) MPMH38-L0 M, I, S, MPMWH32-L0 M, I, S, 1.25 (31.8) 1.41 (35.8) (7.5).28 (7.1) Wood Push Mount WPMH-C M, I, S,.22 (5.6).22 (5.6).38 (9.6).38 (9.6) Hole Drill Depth 1.25 (31.8) 1.25 (31.8) 1 (44.5) Hole Diameter.188 (5).25 (6) (10).313 (8) Weather- Outdoors or Inserted into Pre- Drilled Hole to secure wire, cable, tubing to wood surfaces. Driven into wood with hammer, barbed design holds mount in placerated for 60 lb. pullout. D.31 (7.9).19 (4.8) Plated steel Outdoors or Hammer into Wood Part Numbers listed are for Standard s in Standard Package Quantity. For Package Part Numbers, see Pages 128 & 129. ** Tie Cross Section Sizes: M = Miniature, I = Intermediate, S = Standard, LH = Light Heavy and H = Heavy.

15 Tie Harness Mounts -639 suffix denotes natural heat stabilized nylon -630 suffix denotes black heat stabilized nylon. Tie Harness Mounts are designed to be attached to the wire harness during assembly with 2 cable ties. Ties can be installed by hand or, more efficiently, with PANDUIT PAT Automatic Tie Tooling. Use with Harness Board Standoff Posts and Tie Harness Mount Fixtures (See Page 126). Available with or without corrugated tubing location tab. Panel Thickness Max. Hole Diameter FOR CORRUGATED TUBINGA specially designed location tab on the mount shelf aligns with grooves in corrugated tubing ensuring proper mount location during assembly. THMSP20-C THMSP20-C30 THMSP25-C THMSP25-C30 THMSC35-C639 THMSC35-C630 THMSC60-C639 THMSC60-C630 THMSC85-C639 THMSC85-C630 M, I, S M, I, S 1.54 (39.1) 1.54 (39.1) (11.9).54 (13.7).46 (11.7).72 (18.3).98 (24.9).16 (4.1).23 (5.8).25 (19.0) ( ) ( ) Heat Stabil. / Push Barb Heat Stabil. Heat Stabilized / High temp. FOR DISCRETE WIRINGThere is no location tab for applications not requiring the use of corrugated tubing. THMSP20F-C THMSP20F-C30 (11.9) (4.1) THMSP25F-C THMSP25F-C30 THMSC35F-C639 THMSC35F-C630 THMSC60F-C639 THMSC60F-C630 THMSC85F-C639 THMSC85F-C630 Tie Mounts.54 (13.7).46 (11.7).72 (18.3).98 (24.9) THMSPPush Barb Style.23 (5.8).25 (19.0) ( ) ( ) / Tree Barb Heat Stabil. / Push Barb Heat Stabil. Heat Stabilized THMSCTree Barb Style / High temp. / Tree Barb Part Numbers listed are for Standard s in Standard Package Quantity. For Package Part Numbers, see Pages 128 & 129. ** Tie Cross Section Sizes: M = Miniature, I = Intermediate, S = Standard, LH = Light Heavy and H = Heavy. 93

16 Tie Harness Anchors D Tie Harness Anchors are designed to be attached to the wire harness during assembly with 2 cable ties. Ties can be installed by hand or more effectively with PANDUIT PAT Automatic Tie Tooling. Available with and without corrugated tubing location tab. FOR CORRUGATED TUBINGA specially designed location tab on the mount shelf aligns with grooves in corrugated tubing ensuring proper mount location. THASS8-C THASS8-C30 Tie Mounts.180 (4.6) THASS10-C M, I, S THASS10-C30 (37.9) (26.9) (5.2) THASS25-C.265 THASS25-C30 (6.7) THASS10F-C M, I, S THASS10F-C30 (37.9) (26.9) (5.2) Heat Stabil. / Heat Stabil. / Heat Stabil. / FOR DISCRETE WIRINGThere is no location tab for applications not requiring use of corrugated tubing. THASS8F-C.180 (4.6) THASS8F-C30 Heat Stabil. / THASS25F-C.265 THASS25F-C30 (6.7) Heat Stabil. / Heat Stabil. / #8 (M4) 1/4" (M6) #8 (M4) 1/4" (M6) 94 Part Numbers listed are for Standard s in Standard Package Quantity. For Package Part Numbers, see Pages 128 & 129. ** Tie Cross Section Sizes: M = Miniature, I = Intermediate, S = Standard, LH = Light Heavy and H = Heavy.

17 Tie Mounts Courtesy of Steven Engineering, Inc. 230 Ryan Way, South San Francisco, CA, Main Office: (650) Outside Local Area: (800) THM1SC Tie Harness Mount for Single Tie THM1SC-C THM1SC-C30 M, I, S.98 (24.8).38 Unique Mount is Attached to Harness Automatically as Tie is Installed Secured with only 1 cable tie with the THMF base which opens and holds the mount (See Page 126) ties can be installed by hand with PANDUIT Automatic Tie Tooling Installation Systems (see pages Pages 46 to 49) or pneumatic tool (See Page 52) or hand operated cable tie tools (Pages 53 to 55). Anti-rattle winged design Barb design is easy to insert into pre-drilled hole Strong. 50 lb. vertical extraction force from.250" hole Can be used with auto-fed or loose piece cable ties Panel Thickness Max..187 (4.7) Hole Diameter.250 (6.5) -30 after the pkg. code is for black, heat stabilized nylon 6.6 material for applications up to 221 F. The Tie Harness Mount System: 1. Snap mount into fixture. ears open for cable tie installation. 2. Apply cable tie with automatic cable tie tool. Heat Stabil. / Or apply cable tie by hand and tension with pneumatic cable tie tool. Push Or apply cable tie by hand and tension with handoperated cable tie tool. 3. Pull harness from fixture. ears close, ready for installation. Part Numbers listed are for Standard s in Standard Package Quantity. For Package Part Numbers, see Pages 128 & 129. ** Tie Cross Section Sizes: M = Miniature, I = Intermediate, S = Standard, LH = Light Heavy and H = Heavy. 95

18 Control Panel Mount CPM87S-C M, I, S.89 (22.6) CPM122S-C M, I, S 1.22 (31.0) Installed when switch is installed to save labor. Ideal for high strain areas where cable is routed from panel to panel door. Compatible with most control panel switch designs. D E F G.57 (14.5) A B PP1S-S10-X M, I, S.200 PP1S-S12-X M, I, S.228 (5.8) PP2S-S10-X M, I, S.200 PP2S-S12-X M, I, S.228 (5.8) Tie Mounts Pan-Pole Standoff 2.00 (51) 2.00 (51) 4.62 (117.3) 4.62 (117.3) 1.44 (36.6) 2.07 (52.6) 1.12 (28.4).048 (1.2).048 (1.2).17 (4.3).17 (4.3).76 (19.3) Zinc.82 (20.8) Plated Steel Supports wire bundles above or away from surface. See Drawing Control Panel Switch #12 (M5.5) #12 (M5.5) NOTE: RAFCB Right Angle Flat Base (shown on page 98) can also be used as a wire bundle standoff Part Numbers listed are for Standard s in Standard Package Quantity. For Package Part Numbers, see Pages 128 & 129. ** Tie Cross Section Sizes: M = Miniature, I = Intermediate, S = Standard, LH = Light Heavy and H = Heavy.

19 Connector Rings Closed Connector Rings CR2-M M, I, S.33 (8.4) CR4H-M M, I, S,.57 LH (14.5) Open Connector Ring CROS-M Spacers CSH-D20 M, I, S, CSH-D0 M, I, S, Tie Mounts Spacer, Cross.24 (6.1).36 (9.1) Connect multiple wire bundles or hang bundles from conduit, eliminating the need for saddle clamps (7.6) M, I, S See Drawing See Drawing See Drawing Ties Ties Designed to add on wire bundles without changing cable ties. Connects to M, I, S Ties to separate and/or hang wire cables, hydraulic hoses Ties 500 Weather Resist. Outdoors or Ties 500 Connects two bundles at 90. Provides.19" (4.8mm) space between bundles. Dual cradle design. Recommended max. bundle diameter (each) is.625" (15.9). CSCS-M M, I, S See Drawing Ties 1000 Part Numbers listed are for Standard s in Package Quantity. ** Tie Cross Section Sizes: M = Miniature, I = Intermediate, S = Standard, LH = Light Heavy and H = Heavy. 97

20 Flat System For Flat Widths (Up to) FCBI1-S10-C20 FCBI1-A-C20 FCBI2-S10-C FCBI2-A-C FCBI3-S10-C (76.2) FCBI3-A-C (76.2) FCPI1-C20 FCPI2-C FCPI3-C (76.2) Adhesive supplied by user. Right Angle Base RAFCB RAFCBI1-S6-C20 RAFCBI2-S6-C RAFCBI3-S6-C (76.2) Tie Mounts Secures stacked cables, folds and breakouts plus laminated and molded bus bars. Base FCB Plate FCP Application Use one (1) base, one (1) corresponding size plate and one (1) intermediate cable tie. D E F G 2 (63.5) 2 (63.5) 3 (88.9) 3 (88.9) 4.52 (114.8) 4.52 (114.8) 1.29 (32.8) 2.31 (58.7) 3.32 (84.3) For Flat Width (up to) 1" 2" 3" (76.2) 1 (44.4) 2.78 (70.6) 3.81 (96.8) 1.04 (26.4) 1.04 (26.4) 2.04 (51.8) 2.04 (51.8) 3.04 (77.2) 3.04 (77.2) 1.04 (26.4) 2.04 (51.8) 3.04 (77.2) 2.08 (52.8) none ^ 3.10 (78.7) none ^ 4.12 (104.6) none ^.200 none ^.200 none ^.200 none ^ (3.8).150 (3.8).150 (3.8).150 (3.8).150 (3.8).150 (3.8).095 (2.4).095 (2.4).095 (2.4).095 (2.4).095 (2.4).095 (2.4) & ^Adhesive applied bases are supplied without screw holesdimensions not applicable. See drawing Bundling Application Use two (2) plates (same size) and one (1) intermediate cable tie Adhesive Adhesive Adhesive Ties Ties Ties Selection Chart for PANDUIT Flat System and PAN-TY Ties For, Use One (1) each of the Following and One (1) Tie FCPI1 and FBCI1 (-S10 or -A) or RAFCBI1-S6 FCPI2 and FCBI2 (-S10 or -A) or RAFCBI2-S6 FCPI3 and FCBI3 (-S10 or -A) or RAFCBI3-S6 For Bundling, Use Two (2) each of the Following and One (1) Tie Maximum Flat Stack HeightInches (mm) PANDUIT PAN-TY PLT1.5I Tie FCPI1 8 (21) PANDUIT PAN-TY PLT2I Tie 2.0 (51) FCPI2 1.0 (25) PANDUIT PAN-TY PLT3I Tie 3.7 (94) 2.7 (69) FCPI3 1.7 (44) For perpendicular applications PANDUIT PAN-TY PLT4I Tie 5.2 (133) 4.2 (107) 3.2 (82) 98 Part Numbers listed are for Standard s in Standard Package Quantity. For Package Part Numbers, see Pages 128 & 129.

21 Marker Plates Marker Plates on Rolls MP150-R MP175-R 1 (44.5) M, I, S MP200-R 2.00 MP250-R 2 (63.5) MP150KIT-Q MP250KIT-Q MP350KIT-Q Tie Mounts MP150-C 1.03 (26.2) MP175-C (44.5) (32.5) MP200-C (38.4) M, I, S MP250-C (63.5) (51.6) MP350-C (88.9) (77.0) MP250W175-C (63.5) (44.5) (51.6) MP150-C (26.2) MP175-C (44.5) (32.5) MP200-C M, I, S (38.4) MP250-C (63.5) (51.6) MP350-C (88.9) (77.0) PANDUIT marker plates can be mounted in any direction, either vertically or horizontally as flags, tags, or wrap-around identification plates. They can be marked with nylon marking pens, hot stamped, or in a marking machine. See page 100 for marker pen information. For use in automatic marking equipment. Packaged on spools D Marker Plate Kits 1.03 (26.2) 1.28 (32.5) 1.53 (38.9) 2.03 (51.6) 1.69 (42.9) 1.94 (49.3) 2.19 (55.6) 2.69 (68.3) Description Kit contains 25 MP150 marker plates, 1 PFX-0 marking pen Kit contains 25 MP250 marker plates, 1 PFX-0 marking pen Kit contains 25 MP350 marker plates, 1 PFX-0 marking pen White Ties White Ties Weather Outdoors Weather Ties Part Numbers listed are for Standard s in Standard Package Quantity except Marker Plates on Rolls, which are Package Quantity. ** Tie Cross Section Sizes: M = Miniature, I = Intermediate, S = Standard, LH = Light Heavy and H = Heavy. 99

22 TELCO Products Courtesy of Steven Engineering, Inc. 230 Ryan Way, South San Francisco, CA, Main Office: (650) Outside Local Area: (800) Marking Pens Part Number Tip Description PX-0 PX-2 Regular Regular Red Provide fast drying, permanent, legible identification on nylonwhere ordinary marking pens will not work. of ink is color of pen. Reversible tip to extend life of pen PX-10 Regular White For marking black or other dark-colored parts. Extra tip at end of pen also denotes color PFX-0 PFX-2 PX-0 PX-2 Fine Fine Red TELCO Installation Products Stackable Spacer SACS50-T100 See Footnote For detailed marking on nylon surfaces. of cap and end is color of ink Just one part to inventory. Each spacer snaps by hand into another increases spacer height by 1/2" increments. Because there is only one part, on-site sorting is eliminated. Can be used with up to 3/4" width (B or C lashed cable supports) in parallel or perpendicular applications. Stackable Spacers may be installed using weather-resistant Lashing Ties (See Page 14), weather-resistant Heavy and Light Heavy Ties (See Page 14), and Stainless Steel Ties (see page See Page 73). Most commonly used parts appear in BOLD Hook Wedge 2.08 x 1.16 (52.8 x 21.5) PX-10 perpendicular to strand and cable Weather- Polypropylene Outdoors Ties Easily installed. Part snaps into TELCO Rack. Releasable (with pliers) and reusable. SNAPS INTO RACK OPENING Inches (mm) CHW-C20 See Drawing parallel to strand and cable PFX-0 PFX-2 Underground application Rack Thickness: 3/16" 100 Part Numbers listed are for Standard s in Package Quantity.