T8-03-XX Scope

Transcription

1 T8-03-XX-01 1 Scope 1.1.This specification applies to the indoor and equipment LED Tube light. 1.2.LED Tube light Instead of traditional fluorescent lamp used in business& the family illumination(for example: supermarkets, office buildings, underground parking lot, hotel, Fridge,Icehouse etc ). 2 Structure And Package 2.1.Structure A=435mm,588mm,895mm,1198mm,1498mm,1764mm 3--12

2 2.2.Package 220mm B 240mm 1pc/packing 25pcs/carton B=500mm,650mm,950mm,1250mm,1550mm,1850mm 3 Usages Operating voltage: AC85V~265V 50/60Hz Working environment: -40 C to 40 C Relative Humidity 20%-85% Suitability: for indoor application only. 4 Storage condition Storage environment: -40 C to 80 C Relative Humidity 20%-95%

3 5 Product Characteristics Model No. Rated power (W) Rated Voltage (V) LED Type LED Quantity (PCS) Color Temp. (K) Luminous Flux(Lm) Net Weight (g) CRI (Ra) T AC V SMD ±10% T AC V SMD ±10% T AC V SMD ±10% T AC V SMD ±10% T AC V SMD ±10% T AC V SMD ±10% Quality Warranty 3 Years Quality guarantee is based on storing, installing,operating and maintaining correctly in the normal operation condition; It is not included in our maintaining range when installing inappropriately, breaking the operating rules, and leading to the products damaging; Our company will reserve the right to either repair,parts replacing,or products exchange during the quality warranty period.

4 7. Safety Assurance 7.1 Insulation Resistance The IR shall be at least 50MΩ when apply 500Vdc between primary and secondary 7.2 Dielectric Strength (Hi-pot) Input To Output 3750Vac 60Hz 1minute 3MA When AC voltage of 3.75KV is applied, and the voltage applied to the insulation under test is gradually raised from zero to the prescribed voltage in 1s, and held at that value for 60s between the input and output and between the input and housing, the current sensitivity shall be less than 5mA. After this test, the adapter shall exhibit no electrical and mechanical abnormalities. 7.3 Leakage Current The leakage current shall be less than 0.25m A for class II when power supply is operated maximum input voltage and maximum load. 7.4 Safety Standard 34A_1501NP IEC: :2008 IEC /A1:2010 IEC :2006 IEC62031:2008 IEC62471:2006 IEC :2009 :passed EN /A11:2009 EN :2006 EN /A1:2011 EN62031:2008 EN62471:2008 EN61195:1999 EN62493:2010:passed 7.5. EMI/EMS Standard EN55015 :passed EN :passed EN :passed 7.6.Passed certificates CE/ROHS/TUV MARK/CB/PSE/SAA/C-TICK Remarks:We can get local certificate according the CB certificates easily 8 Safety Notes In Usage Please do not hit or press it with heavy substance; Please Handle and transport gently; Please do not touch and twist the tube when power is on; Tube warm is normal when power is on. Attention: 1) Our Lighting products adopt high brightness LED as the light source,the life reaches 80,000 hours,while the LED brightness degradation is influenced by many environmental conditions,such as surrounding temperature,adequate ventilation and air condition, but also by other electrical device interference.

5 2) The normal operating temperature is from -40C to 40C.If the products work above or below this range for a long time, the life expectancy will be reduced.once under the extreme situation, the internal device will malfunction. 8 Installation Illustrations 8.1Replacement Traditional fluorescent light tube To replace the fluorescent tube starter to LED starter, As shown below: wiring diagram To replace the fluorescent tube starter to LED starter

6 (1) LED tube(1.5m) is designed for the replacement of fluorescent FD-58-E-G13-26/1500 (2) LED tube(1.2m) is designed for the replacement of fluorescent FD-36-E-G13-26/1200 (3) LED tube(0.9m) is designed for the replacement of fluorescent FD-30-E-G13-26/900 (4) LED tube(0.6m) is designed for the replacement of fluorescent FD-18-E-G13-26/600 (5) LED tube(0.45m) is designed for the replacement of fluorescent FD-15-E-G13-26/ Replacement Electronic ballast fluorescent lgiht tube To remove the whole electronic ballast before installation firstly, then connect N and L wire to one side base of G13. Plug the side caps with AC Input in the base with N/L connecting. 8.3 The new layout To connect N and L wire to one side base of G13. Plug the side caps with AC Input in the base with N/L connecting. Input voltage 100V-240V~50/60Hz

7 9 Lighting direction adjustment(only for T8-03-XX-XX products) 9.1 Unlock Button Button Lock Unlock 9.2 Revolve the tube caps to a lighting position 9.3 Lock Button

8 10 Test Data 10.1 Spectrum curve &Chromatism compatible range Spectrum curve Chromatism compatible range

9 10.2 Light Distribution Curve&Max Intensity Distribution Curve 10.3 Illumination Cone Curve

10 10.4 CIE&IES T8-03-XX-01