ASSEMBLY MANUAL OMS-90
|
|
- Alexander Glenn
- 6 years ago
- Views:
Transcription
1 ASSEMBLY MANUAL OMS-90
2 INTRODUCTION This manual should be used by an authorized TOPCON dealer only to assemble the Operation Microscope OMS-90. Two or more persons must assemble this instrument because of its weight. Either a trained person or a worker under the supervision of a trained person should conduct the assembly, in order to ensure safety. Improper or insufficient tightening of bolts can lead to accidents during future use of the operation microscope. Please take care to fasten all bolts properly. Packages The microscope is divided into 4 components for packing. Check that the following 4 packages are delivered. 1. COLUMN, (COLUMN,WEIGHT) 2. BASE,(BASE,FOOT SWITCH) 3. ARM (1ST ARM, 2ND ARM, FOCUSING UNIT) 4. MICROSCOPE If you have ordered an accessory with the microscope, it will be delivered in a separate package, so be sure to check that the separate package has been delivered. (Regarding the procedure for mounting accessories, except the XY translator and the Oblique Illuminator, see the instructions given in OPTIONAL ACCESSORIES on page 26 of the instruction manual.) Standard components (before assembly) 2nd arm 1st arm Focusing unit Microscope Column Base Foot switch 1
3 ASSEMBLY Tools for assembly The base package includes 2 hexagonal wrenches. (It also includes the mounting bolt and washer to be used between the column and base.) (B) (A) (A): for mounting column and base. (B): for opening/closing 1st arm lower cover. For assembling, a Phillips screwdriver and a small slotted screwdriver are required in addition to the above tools. Assembling Assembling is done in the following order: 1 2 Base and column 3 Arm unit 4 Microscope Taking out the component from the package 2 ASSEMBLY
4 TAKING OUT THE COMPONENT FROM THE PACKAGE 1 Take off the band from the external box. Then, lift the external box and take out the 3 boxes. 2 Place each package on a level surface with the thin cushion facings upwards. Thin cushion Thick cushion Pull out the thin cushion first, and you will take out the package easily. 3 Two people must take out the base and arm units because of their weight. Put the unpacked components on a piece of corrugated cardboard, etc. so they will not be damaged. 3 ASSEMBLY
5 MOUNTING THE BASE AND COLUMN Caution Two or more people must handle the base unit. Its weight is approx. 50kg. If handled carelessly, you may be injured unexpectedly. 1 Put the thin cushion on the floor and put the base face down on it. 2 Align the bolt hole position and put the weight on the rear of base. Lift the weight by grasping the knob. 3 Insert bolts into the three holes on the circumference and set them loosely with a hexagonal wrench. Don t tighten the bolts fully. 4 Remove the protective sheet from the column end. Insert the column from the front of base and fit it into the hole positioned at the center of the rear of the base. Then, affix the column with the bolt. Tighten all the above bolts completely. 5 Raise the base unit on which the column has been mounted. 4 ASSEMBLY
6 MOUNTING THE ARM UNIT Caution Two or more people must handle the arm unit. If handled carelessly, you may be injured unexpectedly because of its weight. 1 After taking out the arm unit from the package, and remove the rustproof paper from the shaft. 2 Insert the 1st arm shaft into the column. 3 Loosen the 2nd arm rotation fixing knob and lift up the 2nd arm from the 1st arm by 3~4cm. Rotate the 2nd arm a little and lower it. The locking system for the 2nd arm package is released. 5 ASSEMBLY
7 MOUNTING THE MICROSCOPE 1 Mount the microscope and microscope operation handle onto the focusing unit. Phillips screwdriver Microscope operation handle 2 Remove the 1st arm lower cover. Hexagonal wrench 1st arm lower cover 6 ASSEMBLY
8 3 Pass the light guide through the 2nd arm and the 1st arm as illustrated below. Then, affix the light guide by inserting it into the microscope unit. Light guide Small slotted screwdriver 4 Set the light guide onto the connection unit in the 1st arm. Focusing unit connector Oblique illuminator receptacle XY translator receptacle Pass the light guide through this hole. 7 ASSEMBLY
9 5 Mount the 1st arm lower cover and connect the foot switch connector. 6 Move the 2nd arm up and down and turn the 2nd arm balance adjustment knob to make the upper force the same as the lower one. When the instrument is delivered, it is set to the standard industry specifications. 8 ASSEMBLY
10 OPTIONAL ACCESSORIES XY TRANSLATOR Tools for assembly. Special wrench Special wrench (A) (B) (C) (A) (B) (C) : for installing/removing the focusing unit. : for positioning the focusing unit. : for installing/removing the plate that prevents the nut from falling off. : for preventing the tightening ring from loosening. A 3mm Phillips screwdriver, a 3mm slotted screwdriver and a small slotted screwdriver are required in addition to the above tools. Prepare them beforehand. How to mount Mount the XY translator between the 2nd arm and the focusing unit. Before removing the focusing unit from the 2nd arm, raise the 2nd arm to the highest position possible and tighten the 2nd arm vertical movement fixing knob. 1 Make sure that the power plug is removed from the outlet. Remove the 1st arm lower cover, remove the focusing unit connector and ground the cable and then pull it out. Focusing unit connector Ground 9 OPTIONAL ACCESSORIES
11 2 Remove the light guide from the microscope. Small slotted screwdriver 3 Loosen the slip prevention set screw at the side of the tightening ring. Then, remove the tightening ring. Tightening ring Hexagonal wrench Slip prevention set screw 4 Tighten the rotation fixing knob and loosen the falling-off prevention screw. Rotation fixing knob Falling-off prevention screw 5 While holding the microscope with one hand, loosen the rotation fixing knob with the other. 6 Remove the microscope from the 2nd arm downward and put it on a stable surface. 10 OPTIONAL ACCESSORIES
12 7 Remove the plate that prevents the nut from falling off with a hexagonal wrench and remove the nut with the special wrench. Prevention plate Hexagonal wrench Special wrench Inclination fixing knob Loosen the inclination fixing knob and face the microscope downward. This will allow you to perform this work easily. 8 Loosen the set screw that affixes the joint arm with the hexagonal wrench and then remove the joint arm. Hexagonal wrench 9 Insert the lower shaft of the XY translator into the hole from which the joint arm has been removed. Position the shaft correctly and tighten the screw with the hexagonal wrench. Hexagonal wrench Hole Lower shaft of the XY translator Set screw 11 OPTIONAL ACCESSORIES If the alignment 9) is not correct, the set screw will not go in completely. Please check (9) procedure again in this case.
13 10 Tighten the nut with the special wrench and mount the prevention plate with the hexagonal wrench. Special wrench Hexagonal wrench 11 Insert the XY translator into the 2nd arm and tighten the rotation fixing knob to prevent the XY translator from falling off. Rotation fixing knob 12 Tighten the falling-off prevention screw. Falling-off prevention screw Slotted screwdriver 13 Set the tightening ring and tighten the slip prevention set screw at its side. Slip prevention set screw Hexagonal wrench 12 OPTIONAL ACCESSORIES
14 14 Pass the cables through the 2nd arm cable cover and then, from the hole at the root of the 2nd arm, into the 1st arm. 15 Set the focusing unit connector and ground the cable as before. Then, connect the XY translator connector to the receptacle. XY translator receptacle 16 Mount the 1st arm lower cover. 13 OPTIONAL ACCESSORIES
15 OBLIQUE ILLUMINATOR Accessory Adapter Model 2 is necessary. For assembling, a Phillips screwdriver and a hexagonal wrench for opening/closing the 1st arm lower cover are required. How to mount 1 Put the oblique illuminator s male mount in the female mount of the Accessory Adapter Model 2, then tighten with the accessory lock knob. Accessory lock knob 2 Make sure that the power plug is removed from the outlet and then remove the 1st arm lower cover and the cable cover on the top of the 2nd arm. Cable cover Phillips screwdriver 3 Set the cable on the top of the 2nd arm and mount the cable cover. 14 OPTIONAL ACCESSORIES
16 4 Pass the cable from the root of the 2nd arm into the 1st arm and then connect it to the receptacle in the 1st arm. Oblique illuminator receptacle 5 Mount the 1st arm lower cover. 15 OPTIONAL ACCESSORIES
17 OPERATION MICROSCOPE OMS Printed in Japan TH0
Diaphragm Valve Type 14 Pneumatic Actuated Type AV
Serial No. H-A015-E-7 Contents (1) Be sure to read the following warranty clauses of our product 1 Diaphragm Valve Type 14 Pneumatic Actuated Type AV (2) General operating instructions 2 (3) General instructions
More informationDiaphragm Valve Type 14 Pneumatic Actuated Type AP. User s Manual. Contents H-A065-E. Serial No.
Serial No. H-A065-E Diaphragm Valve Type 14 Pneumatic Actuated Type AP User s Manual Contents (1) Be sure to read the following warranty clauses of our product 1 (2) General operating instructions 2 (3)
More informationInstallation,Operation and Maintenance Manual H-V016-E-10. Serial No. 目次 ( ページ ) 1. Be sure to read the following warranty clauses of our product 1
Serial No. H-V016-E-10 Gauge Valve 目次 ( ページ ) 1. Be sure to read the following warranty clauses of our product 1 2. General operating instructions 2 User s Manual 3. General instructions for transportation,
More informationLANCER FOG LAMP KIT MZ380479EX (for RHD) INSTALLATION AND HANDLING INSTRUCTIONS
LANCER FOG LAMP KIT MZ380479EX (for RHD) INSTALLATION AND HANDLING INSTRUCTIONS Fog lamp Thank you for purchasing the Mitsubishi Genuine Accessory. To install and use the product correctly with proper
More informationRaingear Mustang Windshield Wiper System Installation Instructions E F A
Raingear 1965-1966 Mustang Windshield Wiper System Installation Instructions J I H J G E F A D K 2 speed switch B C L Intermittent switch Please try our way first. This system is designed to fit in your
More informationUniversal Pitch Adjustable Wall Mount For Flat Panel Display UPM-2401
INSTALLATION INSTRUCTIONS Universal Pitch Adjustable Wall Mount For Flat Panel Display UPM-2401 Your new Chief Universal Pitch-Adjustable Wall Mount (UPM-2401) is a quick disconnect mounting system with
More informationGENUINE FOG LIGHT INSTALLATION AND USER S INSTRUCTIONS
GENUINE FOG LIGHT INSTALLATION AND USER S INSTRUCTIONS Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read the
More informationButterfly Valve Type 57P
Butterfly Valve Type 57P Contents Lever Type: 50-200 mm (2-8 ) Body Material: CPVC Gear Type: 50-200mm (2-8 ) Body Material: CPVC (1) Be sure to read the following warranty clauses of our product 1 (2)
More informationTOYOTA TUNDRA BUMPER STEP ASSIST Preparation
Preparation Part Number: PT392-34140 Kit Contents Item # Quantity Reqd. Description 1 1 Linkage Assembly 2 1 Mounting Bracket 3 1 Step Pad 4 1 Hardware Bag 5 1 Bumper Support Bracket 6 1 Bumper Re-enforcement
More informationInstallation Guide VHM Wall Mount Kit for Philips MX600/700/800 and MP60/70 IntelliVue
Installation Guide VHM Wall Mount Kit for Philips MX600/700/800 and MP60/70 IntelliVue The purpose of this guide is to: 1. Describe attachment of Table Top Mount to Mounting Adapter (page 2). 2. Describe
More informationGENUINE FOG LIGHT KIT
GENUINE FOG LIGHT KIT INSTALLATION AND USER S INSTRUCTIONS Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read
More informationTESLA MODEL S REAR UNDER SPOILER & DIFFUSER SYSTEM
TESLA MODEL S Thank you for purchasing your Unplugged Performance Rear Under Spoiler & Diffuser System for the Tesla Model S! Please read this manual carefully prior to installation. REAR UNDER SPOILER
More information(2) Remove the customer's Waste Ink Cartridge and replace to a new one. (3) Make sure GT-541 is not in the middle of any operation.
9. Transporting Preparation before transportation Make sure the following SA5719101 service kit parts are all available. Part name Qty. Cleaning Cartridge 2 IH Head Carton 4 IH Head Case 8 Cap Tube 4 Tube
More informationDiaphragm Valves Type 15
Serial No. H-V031-E-8 Diaphragm Valves Type 15 User s Manual Contents (1) Be sure to read the following warranty clauses of our product 1 (2) General operating instructions 2 (3) General instructions for
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM S2000 AII 26324 Issue Date OCT 2004 PARTS LIST Headrest Speaker System P/N 08A54-S2A-100 3 Small wire ties 2 Headrest speakers 9
More informationPARTS LIST. REPLACEMENT PARTS and ACCESSORIES PREPARATION VN1600. PREPARATION VN1500D and VN800B
INSTALLATION AND OWNER S MANUAL Light Bar N925 for Installation to: Kawasaki VN1500D&E and VN800B Pages 1,2,3 and 5 Kawasaki VN1600 Pages 1, 4 and 5 PARTS LIST QTY. PART NO. DESCRIPTION 1 N925 Light Bar
More informationR81EAA-2 Economizer Circuit Board
FAN 121, 628.1 Motor Actuators Section M Technical Bulletin R81E Issue Date 0993 R81EAA-2 Economizer Circuit Board Applications Setpoint Adjustment Temp T1 T2 S2 1O S 1 8 9 Changeover Relay Refrigeration
More informationTOYOTA SOLARA CONVERTIBLE XM SATELLITE RADIO Preparation. Part Number: Mounting Kit PT
Preparation Part Number: Mounting Kit PT546-06061 Tuner Assy 86180-0W030 Tuner Assy Kit Contents (86180-0W030) 1 1 Tuner Assy, Stereo Component Mounting Kit Contents (PT546-06061) 1 Ground Cable 1 1 Wire,
More informationC35. Assembly Instructions. Mobius Floor Lamp & C Page 1 of 7. Prepare Base (Figures 1& 2)
Mobius Floor Lamp 23-4505 & 23-4505C Page 1 of 7 Prepare Base (Figures 1& 2) A 8-32 Screw (2) B Wireway Cover Plate C Base D Lower Pipe Assembly E Threaded Stud (4) F Hex Nut (4) 1. Carefully unpack the
More informationGENUINE Interior Lighting Kit
GENUINE Interior Lighting Kit INSTALLATION INSTRUCTIONS Thank you for purchasing a genuine Mazda accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read the
More informationGE CARESCAPE Monitor B650 on VHM- PL Variable Height Arm Channel Mount with Vertical Position Lock
GE CARESCAPE Monitor B650 on VHM- PL Variable Height Arm Channel Mount with Vertical Position Lock PRODUCT DETAILS VHM-PL (Locking) Variable Height Arm with 14" / 35.6 cm Extension and Slide-In Mounting
More informationGATE VALVES. Type P (Standard: Plug) Type S (Soft Seal) Contents. (1) Be sure to read the following warranty clauses of our product 1
Serial No. H-V011-E-12 GATE VALVES Type P (Standard: Plug) Type S (Soft Seal) Contents (1) Be sure to read the following warranty clauses of our product 1 User s Manual (2) General operating instructions
More informationFranking system PostBase One Service documentation
Print system Andreas Nagel VST; ServDok_PostBase-One_Kap04_02_printer_system_003eng.docx Revision May, 10th/ 2016 page 1 Chapter 4.2 Printer System 1 MOTORS IN THE PRINTER SYSTEM 3 2 PIVOT ASSEMBLY POSITIONS
More informationC35 Mobius Floor Lamp & C Page 1 of 7
Mobius Floor Lamp 23-4505 & 23-4505C Page 1 of 7 Prepare Base (Figures 1& 2) A 8-32 Screw (2) B Wireway Cover Plate C Base D Lower Pipe Assembly E Threaded Stud (4) F Hex Nut (4) 1. Carefully unpack the
More informationBucket Harness. Installation Instructions. for Electric Club Car Precedent
Bucket Harness for Electric Club Car Precedent Installation Instructions Electric Club Car Precedents manufactured after January 1, 2008 require an additional harness to allow the installation of light
More informationService Manual Air Plus Second Stage
Service Manual Air Plus Second Stage Includes XS Series Second Stage Copyright 2002, Cressi-sub Revised 3/2002 2 Air Plus Second Stage Service Manual Contents BEFORE STARTING... 3 DISASSEMBLY... 3 PARTS
More informationSRS AIRBAG Toyota RAV4. Supplemental Restraint System - RAV4 PRECAUTION CAUTION:
2005 RESTRAINTS Supplemental Restraint System - RAV4 SRS AIRBAG PRECAUTION CAUTION: The TOYOTA RAV4 is equipped with SRS that includes a driver airbag, front passenger airbag, side airbag and curtain shield
More informationInstallation Instructions Z-Gate Shifter
Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic
More informationSZ2-ILA INSTRUCTIONS TRANSMITTED ILLUMINATION ATTACHMENT SZ-ADD SZ-POL-2 SZH-CLJ. Optional Modules
Optional Modules SZ-ADD SZ-POL-2 SZH-CLJ INSTRUCTIONS TRANSMITTED ILLUMINATION ATTACHMENT This instruction manual is for the Olympus Transmitted Illumination Attachment. To ensure the safety, obtain optimum
More informationFD Conveyor for FD 260 Tabber
FD 260-20 Conveyor for FD 260 Tabber Operator Manual 1/2011 First Edition TABLE OF CONTENTS 1. INTRODUCTION... 1 1.1 FD 260-20 DESCRIPTION... 1 1.2 ITEMS INCLUDED... 1 1.3 OPERATING MANUAL SAFETY TERMS...
More informationFD 150 Document Signer
FD 150 Document Signer OPERATOR MANUAL FIRST EDITION Thank you for purchasing the Formax FD 150 Document Signer The FD 150 has been tested and found to comply with the limits for a Class A digital device
More informationGENUINE MUD FLAP (REAR)
GENUINE MUD FLAP (REAR) INSTALLATION AND USER S INSTRUCTIONS Thank you for purchasing a Genuine Mazda Accessory. Before removal and installation, be sure to thoroughly read these instructions. Please read
More information3-Way Ball Valve Type 23H
Serial No. H-V062-E-4 contents 3-Way Ball Valve Type 23H User s Manual (1) Be sure to read following warranty clauses of our product 1 (2) General operating instructions 2 (3) General instruction for transportation,
More informationstationary massage table
stationary massage table Operator Manual TABLE OF CONTENTS Warnings... 3 Table Specifications Aura Basic... 4 Aura Lift Back... 5 Aura Deluxe... 6 Installation Caution... 7 Parts Included...7 Instructions
More informationInstallation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683
Installation Instructions QuickSilver Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 WORK SAFELY! For maximum safety, perform this installation
More informationX.L. BAND W/ SPRING ASSIST INSTRUCTION MANUAL
PARTS LIST X.L. BAND W/ SPRING ASSIST INSTRUCTION MANUAL (2) Bands (1) Handle assembly (2) Side hinge assemblies (1) Left rear hinge assembly (1) Right rear hinge assembly (2) front spring s (2) rear spring
More information2004 Lexus LS430. Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS
2004 Lexus LS430 Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS OVERHAUL If the airbag connector is disconnected with the ignition switch in the ON position, DTCs will be recorded. When
More informationINTEGRATION MODULE HARNESS KIT A4, F4
GENUINE INTEGRATION MODULE HARNESS KIT A4, F4 INSTALLATION INSTRUCTIONS Vehicle: Mazda MX-5 Parts numberbbm2 79 CFZ (ipod integration module) C9FA V6 029 (Harness Kit A4) C9FB V6 029 (Harness Kit F4) Thank
More informationInstallation Notes. PlayPorTT Kiosk Anti-Tip Safety Cable. (p/n )
May 2010 900410-001 Rev. 01 About This Document This document is intended for: Operators of TouchTunes PlayPorTT wireless game and music systems. TouchTunes Field Service, Customer Support, and Sales personnel.
More informationVHM-P (Non-Locking) Variable Height Arm with VESA Mounting Plate for 75 x 75mm or 100 x 100mm applications
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com VHM-P (Non-Locking) Variable Height Arm with VESA Mounting Plate for 75 x 75mm or 100 x 100mm applications
More informationMounting and Operating Instructions EB EN. Type 3271 and Type 3277 Pneumatic Actuators. Actuator areas: 175v2, 350v2, and 750v2 cm²
Type 3271 and Type 3277 Pneumatic Actuators Actuator areas: 175v2, 350v2, and 750v2 cm² Translation of original instructions Type 3271 (left) and Type 3277 (right) Pneumatic Actuators Mounting and Operating
More informationSwing Check Valve ASAHI AV VALVES. Contents. User s Manual. (1) Be sure to read the following warranty clauses of our product 1
Serial No. H-V013-E-13 Swing Check Valve User s Manual Contents (1) Be sure to read the following warranty clauses of our product 1 (2) General operating instructions 2 (3) General instructions for transportation,
More informationDiaphragm Valve Type 72
Serial No. H-V001-E-8 Diaphragm Valve Type 72 User s Manual Contents (1) Be sure to read the following warranty clauses of our product 1 (2) General operating instructions 2 (3) General instructions for
More information2 nd Generation Sport Trac LED 3 rd Brake Light Replacement Project By Kevin Collins
2 nd Generation Sport Trac LED 3 rd Brake Light Replacement Project By Kevin Collins SCOPE: This project will assist you to replace the factory 3 rd Brake Light with Recon s LED 3 rd Brake Light: Part
More informationVCHR Series. Direct Operated Regulator for 6.0 MPa (Relieving Type) Service life: 10 million cycles. How to Order
Direct Operated Regulator for 6.0 MPa (Relieving Type) VCHR Series Service life: 0 million cycles Using NSF-H-certified grease on the guide ring (sliding) part. Improved durability under a high pressure
More informationInstallation Instructions Hammer Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80885
Installation Instructions Hammer Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80885 WORK SAFELY! For maximum safety, perform this installation on
More informationDisassembling and Assembling
Disassembling and Assembling How to disassemble and assemble the controller box 1. Disassembling of controller box Phillips screwdriver, 8# wrench, scissors or penknife. 1) First dismantle the rear bottom
More informationCOMPONENT WORK SAMPLE 14 Integrated Peer Performance MAINTENANCE MANUAL
COMPONENT WORK SAMPLE 14 Integrated Peer Performance MAINTENANCE MANUAL Copyright 2003 VALPAR International Corporation P.O. Box 5767 Tucson, Arizona 85703-5767 All rights reserved. No part of this manual
More informationMustang CLASSIC LIGHT BAR INSTALLATION INSTRUCTIONS CDC #
1990-1993 Mustang CLASSIC LIGHT BAR INSTALLATION INSTRUCTIONS CDC # 101000 Kit Components: 1 Light Bar 4 Bolts ( 5 / 16-18 x 2.5 ) #182010 4 Washer #182005 4 Shims #182009 2 Dark Blue Connectors #182004
More informationLGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions
LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and
More informationInstallation Guide Philips MP2 IntelliVue M-Series Arm (12'' or 8'') Rail Mount Kit
Installation Guide Philips MP2 IntelliVue M-Series Arm (12'' or 8'') Rail Mount Kit The purpose of this guide is to: 1. Describe mounting of MP2 equipment on Mounting Bracket (page 2). 2. Describe mounting
More informationi IMPORTANT! The installation instructions contained in this manual should only be carried out by a qualified technician. INSTALLATION/USER MANUAL
i IMPORTANT The installation instructions contained in this manual should only be carried out by a qualified technician. INSTALLATION/USER MANUAL i IMPORTANT TRANSPORTING THE CLIENT WITHIN A WHEELCHAIR
More information1. General Description
General Description 1. General Description A: SPECIFICATION Front Rear Model Wheel arch height (Tolerance: +12 mm 24 mm ( +0.47 in 0.94 in)) mm (in) 376 (14.8) Camber (Tolerance: 0 45 Differences between
More informationRotary Damper. Type 57: 40~350mm (1 1/2 ~14 ) Type 56: 400mm (16 ) Type 75: 450~600mm (18 ~24 ) Contents
Serial No. H-V038-E-8 Rotary Damper Type 57: 40~350mm (1 1/2 ~14 ) Type 56: 400mm (16 ) Type 75: 450~600mm (18 ~24 ) Contents (1) Be sure to read the following warranty clauses of our product 1 (2) General
More informationQuestions, problems, missing parts? If you have questions about this product or need technical support, call the Amerisun customer service department
Questions, problems, missing parts? If you have questions about this product or need technical support, call the Amerisun customer service department at 1-800-791-9458. Also contact Amerisun at Amerisuninc.com
More informationButterfly Valves ASAHI AV VALVES
Serial No. H-V030-E-8 Butterfly Valves Type 56: 400mm (16 ) Body: PP, PVDF Type 75: 450-600mm (18-24 ) Body: PP, PVDF Type 56D: 400mm (16 ) Body: PDCPD Type 75D: 450-600 mm (18-24 ) Body: PDCPD Contents
More informationInstallation Guide Folding L-Bracket with Display Mounting Extension and Keyboard Tray for M-Series or VHM Arm
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Folding L-Bracket with Display Mounting Extension and Keyboard Tray for M-Series or VHM Arm
More informationVHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm with Slide-In Mounting Plate
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 +1.707.773.1100 Fax 707.773.1180 www.gcx.com VHM-P (Non-Locking) and VHM-PL (Locking) Variable Height Arm with Slide-In Mounting Plate (Refer to qualified
More informationZ-Gate Universal Shifter
Installation Instructions Z-Gate Universal Shifter Fits: GM, Ford, Lincoln and Chrysler Transmissions See Application Guide for Specific Applications Part #80681 Rev 06/01/2018 WORK SAFELY! For maximum
More informationA B 0 0 C D E 6 7 G F F H 8 9 K M O O L N I J 1
1 2 1 5 4 3 2 2 1 6 3 8 7 1 9 4 C A B 5 0 0 D E 6 G 7 F F H 8 K 9 M O O I J L N 1 GENERAL OPERATIONAL PRECAUTIONS 1. Keep work area clean. Cluttered areas and benches invite accidents. 2. Avoid dangerous
More informationTOYOTA TUNDRA BUMPER STEP ASSIST Preparation
Preparation Part Number: PT392-34140 Kit Contents 1 1 Linkage Assembly 2 1 Mounting Bracket 3 1 Step Pad 4 1 Hardware Bag 5 1 Bumper Support Bracket 6 1 Bumper Re-enforcement Bracket Hardware Bag Contents
More informationInstallation Guide Philips MP90 VHM Wall Mount Kit
Installation Guide Philips MP90 VHM Wall Mount Kit The purpose of this guide is to describe the procedures for installing the MP90 VHM Wall Mount Kit. Table of Contents Section 1.0: Mounting the VHM-Series
More informationShowBoat 66. For Factory racks: Check fitlist. notes, for your vehicle s crossbar spread. CROSSBAR SPREAD
For Factory racks: Check fitlist notes, for your vehicle s crossbar spread. ShowBoat 66 Support Bar (2x) ROLLER (1x) END CAP (4x) END CAP (2x) STOP COLLAR (1x) TORX WRENCH (1x) Tape Measure (1x) Front
More informationPRO RATCHET UNIVERSAL SHIFTER
Installation Instructions PRO RATCHET UNIVERSAL SHIFTER Fits: GM, Ford and Chryslers w/automatic Transmission See Application Guide for Specific Vehicles Catalog # 80842 WORK SAFELY! For maximum safety,
More informationReplacing the Batteries in the Fortress LI 660
Replacing the Batteries in the Fortress LI 660 This FTS describes how to replace the batteries in Fortress LI 660 units. Batteries should be replaced by a qualified technician. If you have any questions
More informationUniversal Pitch-Adjustable Wall Mount For Flat Panel Display PLP-91/D
INSTALLATION INSTRUCTIONS Universal Pitch-Adjustable Wall Mount For Flat Panel Display PLP-91/D Your new Wall Mount (PLP-91/D) is a quick disconnect mounting system with adjustability between 0 and 15
More informationLABOUR ESTIMATE GUIDE
INSTALLATION INSTRUCTIONS FOR 2001-2005 Audi A4 1.8T These instructions are applicable to vehicles equipped with either manual or automatic transmissions Thank you for choosing to purchase a Carbonio Intake
More informationManual Height Adjustable Desk Frame
Manual Height Adjustable Desk Frame Instruction Manual SKU: DESK-V101M Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products/desk-v101m
More informationLIMIT SWITCH SPECIAL INSTRUCTIONS
LIMIT SWITCH SPECIAL INSTRUCTIONS Use these instructions to install a limit switch. Read and follow these instructions along with the standard instructions carefully before installing or using tarp system.
More informationRTX 2000 Thomas Compressor TG-550 Graco PN
RTX 2000 Thomas Compressor TG-550 Graco PN 246888 Print of Complete Compressor--------------Page 2 Instruction for Kit 118628-------------------Page 3 Instruction for Kit 287845-------------------Page
More informationDiaphragm Valve True Union Diaphragm Valve Pneumatic Actuated Type AI
Serial No. H-A058-E-11 Contents Diaphragm Valve True Union Diaphragm Valve Pneumatic Actuated Type AI (1) Be sure to read the following warranty clauses of our product 1 (2) General operating instructions
More informationSCION tc ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PTS21-21070 Kit Contents Item # Quantity Reqd. Description 1 2 Hardware Kit w/ power harness 2 1 Front Left Illuminated Door Sill Protector 3 1 Front Right Illuminated Door Sill
More informationBe sure to carry out the following before starting work
Be sure to carry out the following before starting work If an older version of the CMU software is being used, the CarPlay/Android Auto-compatible USB hub may not be recognized. If the software version
More informationProduct Number : ( 3DL-VW / 3DL-BM) Please check the contents of the package. Main Unit [ (D) mm] Zip tie 3
(3DL-VW / 3DL-BM As of November, 207 No.2) USER S MANUAL Product Number : ( 3DL-VW / 3DL-BM) Thank you for purchasing PIVOT product. Please read this manual carefully and keep it for future reference.
More informationTOYOTA TUNDRA TVIP V4 REMOTE ENGINE STARTER (RES)
Preparation Part Number: 08586-OC910 Conflicts Do not install into vehicles without RKE systems. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM Radio NOTE:
More informationPOLAR BT INSTALLATION MANUAL FOR SKODA OCTAVIA (1Z)
POLAR BT INSTALLATION MANUAL FOR SKODA OCTAVIA (1Z) I N D E X 1. BEGINNING 2 2. DISASSEMBLY 3 3. HOW TO CONNECT POLAR BT 10 4. FINISHING THE INSTALLATION 13 Polar BT Installation manual Rev. A Sheet :
More information16" STAND FAN WITH REMOTE
OWNER S MANUAL 16" STAND FAN WITH REMOTE MODEL:FS40-8JR READ AND SAVE THESE INSTRUCTIONS Attention: Pictures in the IM are for reference only. CAUTION Read rules for safe operation and instrucions carefully.
More informationDiaphragm Valve Type 14 Pneumatic Model Type AV
ASAHI AV Valves Serial No. H A015 E 1 Diaphragm Valve Type 14 Pneumatic Model Type AV User s Manual (1) General operating instructions Contents (2) General instructions for transportation, unpacking and
More informationIn order to receive proper credit for returned units and
NMD 100 Extension Assembly TDN 07103-00442 May 15, 2012 Read All Instructions Before Proceeding Triton Systems will not be responsible for items damaged or lost during shipping, unpacking or assembly.
More informationHydroMassage Installation Overview- 340 Series
HydroMassage Installation Overview- 340 Series For more detailed instructions, please refer to the HydroMassage Product Manual, or visit http://www.hydromassage.com/customer-installation.htm **DELIVERY
More informationProduct Description. Product Numbers. Warning/Caution Notations. Required Tools. Wiring. Prerequisites
Document No. 155-302N VE 598 Electronic Flowrite Valve Field Assembly Product Description The VE 598 Electronic Valve Assemblies consist of an electronic actuator, linkage kit, and a valve body assembly.
More informationInstallation instructions
Installation instructions Akrapovič Exhaust System: Slip-On for the Laborghini Gallardo 550-2 Coupe Laborghini Gallardo 560-4 Coupe / Spyder Laborghini Gallardo 570-4 Coupe / Spyder Congratulations on
More informationBBAIR V Conveyor Dryer
BBAIR-08-0V Conveyor Dryer wide by 8 long conveyor dryer with forced air and infrared Document # 6- Assembly and Operating Instructions Please review all these instructions prior to assembly. The Big Buddy-Air
More information2015+ HELLCAT 6.2L HEMI System vehicle specific plate system xx
These installation instructions will guide you through installing the Nitrous Outlet 2015+ Hellcat 6.2L Hemi Vehicle Specific Plate System on your vehicle. Before you get started, remember to never use
More informationMULTILUBE SYSTEM INSTALLATION AND MAINTENANCE
MULTILUBE SYSTEM TABLE OF CONTENTS 1 PUMPING UNIT INSTALLATION...1 1.1 Installing the supporting blocks and the pumping unit...1 1.2 Installing the main line on the pumping unit...3 1.3 Installing the
More informationSpear & Jackson 37 cc Petrol Chainsaw Original Operating Instructions
Spear & Jackson 37 cc Petrol Chainsaw Original Operating Instructions Assembly Manual After Sales Support UK/Ireland 0151 649 1500 Republic of Ireland 1890 946 244 Web www.einhell.co.uk Important - Please
More informationWhite Industries ENO Eccentric Rear Hub Instructions
White Industries ENO Eccentric Rear Hub Instructions Tools required: 4mm allen/hex wrench, 19mm open end wrench, 9mm open end wrench or bench vise, ENO Eccentric Axle Tool or 10mm socket, bearing puller
More informationPRECISION MICROSCOPES
SEILER 202/402 Owner s Manual PRECISION MICROSCOPES A Division of Seiler Instrument Company 082608 PRECISION MICROSCOPES A Division of Seiler Instrument Company microscope beam split-port and wedge the
More informationN41421 Peacemakers Exhaust for Harley- Davidson Dyna Series
Please read these instructions carefully and thoroughly before beginning work. Before installing accessory, carefully consider whether one possesses the necessary technical skills and workshop tools to
More informationZ48, Z54, ZSR54, ZSR60 ZXT54, ZXT60, ZT60, ZT72,
Light Kit Assembly Instructions Z44 & Z2 w/s/n 472620+ Z48, Z4, ZSR4, ZSR60 ZXT4, ZXT60, ZT60, ZT72, ZT60i, ZT72i, ZT360, & ZT372 Manual No. 37-78M Before You Start! When you see this symbol, the subsequent
More informationPART NUMBER: E361SAJ302
: A KIT CONTENTS: designed for forks with safety tabs. Forks with SafetyTabs 2X NOTICE: YOU MAY HEAR AN INCREASED LEVEL OF WIND NOISE OR WIND RUSH SOUND AS A RESULT OF INSTALLING THIS RACK ON YOUR VEHICLE.
More informationMirror Solutions Bevel & Pivot Models Installation Instructions INSTALLATION INSTRUCTIONS. Figure 1
Installation Instructions Mirror Solutions Bevel & Pivot Models 620095-620098 Mirror Solutions Bevel - Models # 620095 & 620096 Mirror Solutions Pivot - Models # 620097 & 620098 Figure 1 INSTALLATION INSTRUCTIONS
More informationCarousel Unit User Manual Replacing the Check Stand Motor
Carousel Unit User Manual Replacing the Check Stand Motor 02/01/2017 1 Table of Contents Tools:... 3 Turn Off Power to the Unit:... 4 Remove Power Switch... 5 Remove Electric Eyes:... 6 Remove POS (Point-Of-Sale)
More informationASSEMBLY INSTRUCTIONS
CONTENTS ASSEMBLY INSTRUCTIONS... 1 TO THE DEALER... 1 SAFETY... 1 UNPACKING AND CHECKING PARTS... 2 Unpacking Wooden Crate...2 Checking Parts...3 TRACTOR PREPARATION... 4 Tool Box (CAB MODEL)...4 ASSEMBLY...
More informationInstalling the CO 2 Cryogenic Oven Cooling Kit
Installing the CO 2 Cryogenic Oven Cooling Kit Agilent 6850 Series II Network GC System Accessory G2625B This kit contains: Description Chassis 1 Chassis Cover 1 Ship kit: 1 Cooling coil 1 Coil bracket
More informationMaintenance Information
Form 04584058 Edition 1 November 2004 Air Impactool 2141P and 2141PSP Maintenance Information Save These Instructions Disassembly General Instructions 1. Do not disassemble the tool any further than necessary
More informationInstallation instruction do88 Intercooler for SAAB 9-3 1,9 TTiD
Installation instruction do88 Intercooler for SAAB 9-3 1,9 TTiD This instruction shows how to replace the OEM intercooler with this performance intercooler. At this type of installation we always recommend
More informationAt-A-Glance Trailer Assembly Overview
At-A-Glance Trailer Assembly Overview VERY IMPORTANT; ALWAYS REFER TO YOUR OWNER S MANUAL FOR PROPER OPERATING AND SAFETY INFORMATION REGARDING YOUR TRAILER. INCASE OF LOSS GO TO WWW.UTILITYMATE.COM BEFORE
More information1. General Description
General Description 1. General Description A: COMPONENT (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (24) (23) (22) (21) (20) (19) (18) (17) (16) (15) (14) (13) (12) (11) AB-02007 (1) Curtain airbag module
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. (Trunk Mount) 2009 CIVIC 4-DOOR AII 40184 Issue Date AUG 2008 PARTS LIST 8 Cushion tapes Changer Attachment (Sold Separately) P/N 08B26-SNA-101
More information