Lighting. Lamps & Lighting. Lamps & Lighting - contents. Visit our website for additional price information and exciting promotions

Transcription

1 ORDERLINE contents 1124 Lamps 1124 Light Fittings 1132 Components 1137 Task 1140 Visit our website for additional price information and exciting promotions 1123

2 Fluorescent Triphosphor Triphosphor tubes have longer life, a lower mercury content, better colour rendering and higher lumen maintenance than their Halophosphate counterparts. The tubes are available in a variety of colour tematures from 3000K (warm white) to 6000K (daylight) Extended life expectancy which can be increased by upto 20,000 hours with the use of high frequency luminaires Shatter resistant versions available which retain the fragments in the event of a breakage Option of triphosphor tubes with internal reflectors, which reduce waste light and increase light output by up to 75% 16mm (T5) tubes provide a compact alternative to T8 tubes, offering peak formance at 35 C and typically provide 5% more efficiency in most ceiling applications when compared to equivalent T8 tubes Guide to colour temature Temature 3000K 3500K 4000K 6500K Description Warm White White Cool White Daylight Effect Cosy, Welcoming Neutral Clean, Professional Sterile, Cold Typical Applications Reception/ Rest Areas General Purpose Office / Production Areas Toilets, Kitchens Triphosphor T5 Triphosphor 14 W Colour Rendering Lumens 1200 Life (Hrs) Brand Osram Fluorescent Halophosphate ON-LINE Halophosphate fluorescent tubes are lower in cost than Triphosphor types, and are ideal for undemanding applications. Guide to colour temature Temature 3000K 3500K 4000K 6500K Description Warm White White Cool White Daylight Effect Cosy, Welcoming Neutral Clean, Professional Sterile, Cold Typical Applications Reception/ Rest Areas General Purpose Office / Production Areas Toilets, Kitchens Miniature T5 ( 5 8") Halophosphate Tube Dia. 16 mm Lumen Maintenance 80% Colour Temature Lumens Length Brand Colour Rendering GE * GE K Length (in.) unit unit unit Colour Temature (K) Triphosphor T unit unit Suitable for general use in a wide range of applications, giving improved life and colour rendering when compared to halophosphate tubes. Colour Rendering 85 Life (Hrs) Lumen Maintenance 90% Tube Dia. T8 mm Energy Saving T5 Wattmiser Tubes Direct retro-fit to replace standard T5 tubes Improved coatings and gas fill produce comparable light outputs Saves around 5% of the running costs The 35W replacement tube will save 50kWh of electricity over its life Long life of 25,000 hrs on 3hr switches, rising to 30,000 on a 12 hour switching cycle Colour Temature 3000 K Diameter T5 Triphosphor Life (Hrs) Colour Rendering 85 CRI Lumens Length Length (ft) Colour Temature (K) unit a unit unit unit unit unit Length Lumens Equivalent unit unit Circular Fluorescent Circular Fluorescent Replacement circular lamps for task lamps and illuminated magnifiers Stock Number has good colour rendering, ideal for use in colour critical applications such as textiles, print and photography. Lumen Maintenance 80% Colour Rendering 82 Tube Dia. T mm Colour Temature 4000 K Life (Hrs) Lumens W Dia. 210 mm Description 22W Colour Matching unit Compact Fluorescent Lamps Retro-fit Stick Retrofit Compact Fluorescent Lamps Note: Nominal supply voltage 230Vac Lamp Lumens Lamp Length Dia. Life (Hrs) Brand Liliput SES Megaman Liliput ES Megaman Liliput ES Megaman Liliput BC Megaman Liliput ES Megaman Liliput BC Megaman Liliput ES Megaman Liliput BC Megaman Dulux EL SES Osram GE Biax ES GE Description Retrofit CFL 2700K SES 5W unit Retrofit CFL 2700K ES 8W unit Retrofit CFL 2700K ES 11W unit Retrofit CFL 2700K BC 11W unit Retrofit CFL 2700K ES 14W unit Retrofit CFL 2700K BC 14W unit Retrofit CFL 2700K ES 20W unit Retrofit CFL 2700K BC 20W unit Dulux EL 5W SES 2700K unit Biax 15W ES 4000K unit OM = Order Multiple a New product to range * manufacturers information unavailable at time of printing

3 ORDERLINE SPIRAL Series Long lamp life Lightweight and compact design Manufactured from recyclable and environmentally friendly materials Alternative to incandescent lamps Typical applications include table, wall and pendant lamps PL-S, Biax S Single-loop style compact fluorescent lamps 2-pin G23 cap PL-S and Biax S No Loops 1 SPIRAL Dimmable No Colour temature 3000 K Life (Hrs) GLS Equivalent Lamp Dia. Lamp Length Lumens 8 40 SES E ES E BC B Lamp 8 SES E14 a unit ES E27 a unit BC B22 a unit Globe and Miniature Round CFL Classic round shape and a similar size to conventional lamps Round/golfball style has a translucent silicone cover for more even light distribution and limited shatter protection Colour temature 3000 K Colour Rendering 82 Dimmable No Globe Dia. 98 mm Lamp Length W GLS Equivalent 100 W Life (Hrs) 10,000 Lamp Globe ES unit Globe BC unit CFL Reflector Designed as direct replacements in non-dimming and dimming (see stock numbers or ) applications, these lamps retain a very similar appearance and dimensions to a conventional reflector lamp, but with lower running costs. Colour temature 3000 K GLS Equivalent 120 W Colour Rendering 82 Dia. 121 mm Dimmable No Lamp Length 133 PAR38 ES Life (Hrs) W PAR38 ES unit SL E Pro Note: Not suitable for use with dimmers. Nominal supply voltage 230Vac SL Dia. 51 mm Temature (K) 2700 Life (Hrs) Colour Rendering 82 Weight 104 g Lamp GLS Equivalent BC ES ES Lamp BC unit ES unit ES unit Compact Fluorescent Lamps Energy saving of typically 75-80% when compared to GLS lamps of a comparable light output Long life, (10000 hours typically) which equates to lower maintenance costs 2-pin version have integral starters and should only be used with switch start ballasts 4-pin versions are designed primarily for use with high frequency ballasts or in emergency lighting applications Triphosphor coatings give good colour rendition Ra 80 to 89 Choice of colour tematures Compatibility Please note that some types of lamps are inter-changeable, as long as lamps of similar characteristics are used. These are: Philips PL-L and GE Biax L Philips PL-S (2pin), Osram Dulux S and GE Biax S Philips PL-S (4pin), Osram Dulux S (4pin) and GE Biax S/E Philips PL-C (2pin), Osram Dulux D and GE Biax D Philips PL-C (4pin), Osram Dulux D (4pin) and GE Biax D/E Diagram Temature (K) Lamp Length Lumens Brand Number of Pins Lamp PL-S Philips 2 G PL-S Philips 2 G Biax S GE 2 G PL-S Philips 2 G Biax S GE 2 G Biax S GE 2 G PL-S Philips 2 G Biax S GE 2 G PL-S Philips 4 2G Description PL-C, Biax D, Dulux D Dual-loop style 2-pin G24d cap Biax C, Dulux D and PL-C 4-pin G24q cap Dulux D/E and PL-C No Loops 2 Number of Pins Temature (K) Lamp GLS Equivalent Lumens Brand PL-C G24d Philips Dulux D G24d Osram PL-C G24d Philips PL-C G24d Philips Dulux D G24d Osram PL-C G24d Philips PL-C G24q Philips PL-C G24q Philips PL-C G24q Philips PL-C G24q Philips Description Temature (K) Temature (K) PL-S G23 7W unit PL-S G23 7W unit Biax S G23 9W unit PL-S G23 9W unit Biax S G23 9W unit Biax S G23 11W unit PL-S G23 11W unit Biax S G23 11W unit CFL 11W 4-pin PL-S lamp unit PL-C 2 pin 13W unit Dulux D 2 pin 18W unit PL-C 2 pin 18W unit PL-C 2 pin 18W unit Dulux D 2 pin 26W unit PL-C 2 pin 26W unit PL-C 4 pin 18W unit PL-C 4 pin 18W unit PL-C 4 pin 26W unit PL-C 4 pin 26W unit Visit our website for additional price information and exciting promotions 1125

4 PL-L, Biax L, Dulux L GLS Lamps Standard GLS Dia. 50 ON-LINE Single-loop style 2G11 4-pin caps For use with external starters and ballasts Note: 40W and 55W lamps can only be used with high frequency control gear Description Voltage (V ac) Finish Length Brand Number of Pins 4 No Loops 1 40 W BC 230V, Clear BC (B22) 230 Clear 106 GE Lamp 2G11 60 W BC 230V, Clear BC (B22) 230 Clear 106 GE Description Temature Lamp Length Lumens Brand 60 W ES 25V, Clear ES (E27) 25 Clear 107 Osram (K) 60 W ES 50V, Pearl ES (E27) 50 Pearl 107 GE W ES 230V, Clear ES (E27) 230 Clear 107 GE PL-L 2G11 18 W PL-L Philips Dulux L 2G11 18 W Dulux L Osram PL-L 2G11 18 W PL-L Philips PL-L 2G11 24 W PL-L Philips Dulux L 2G11 36 W Dulux L Osram PL-L 2G11 36 W PL-L Philips Description Biax T, Biax T / PL-T Triple-loop compact flourescent lamps available in both 2-pin and 4-pin formats with GX23 bases PL-T Colour temature 3000 K Lamp Lumens Lamp Length 26 GX24q GX24q GX24q Description 2D / PL-Q / Lynx-Q Diagram Number of Pins Temature (K) Lamp Lamp Length Lumens GR8 140 x 140 x GR8 140 x 140 x GR10q 140 x 140 x GR10q 205 x 250 x GR10q 205 x 250 x Description Temature (K) Colour temature (K) Temature (K) PL-L 2G11 18 W unit Dulux L 2G11 18 W unit PL-L 2G11 18 W unit PL-L 2G11 24 W unit Dulux L 2G11 36 W 4000 a unit PL-L 2G11 36 W unit PL-T 4 pin 26W unit PL-T 4 pin 32W unit PL-T 4 pin 42W unit D 2-pin 16W 2700 K unit D 2-pin 16W 3500 K unit D 4-pin 16W CFL unit lamp 3500 K 2D 4-pin 28W CFL unit lamp 3500 K 2D 4-pin 38W 3500 K unit My Account Description 40 W BC 230V, Clear unit W BC 230V, Clear unit W ES 25V, Clear unit W ES 50V, Pearl unit W ES 230V, Clear unit Energy Saving GLS A mains voltage halogen capsule contained within a traditional GLS bulb. Energy savings of 30% against conventional GLS technology Twice the life of a normal GLS Fully dimmable Voltage 230 V Length 96 mm Dia. 55 Description Rough Service For use in areas of high vibration and shock Available in bulk packs GLS Dia. 60 Finish Pearl Voltage (V ac) Length Brand BC GE BC Osram BC GE E GE E Osram E Osram BC Osram ES GE Round Miniature Small lamps for use in confined spaces Voltage 230 V ac BC (B22) Round / Golf Ball Finish Clear Dia. 45 Length 72 mm 40 W BC (B22) unit Linear Equivalent Ideal for use as under shelf or display lighting, etc. 70W BC 230V Clear unit W ES 230V Clear unit W ES 230V Clear unit W ES 230V Clear unit S15s Strip Voltage 230 V ac Dia. 26 Description 240V BC 40W unit V BC 60W unit V BC 100W unit V ES 40W unit V ES 60W unit V ES 100W unit V BC 60W unit V ES 60W lamp unit OM = Order Multiple a New product to range

5 Reflector ORDERLINE Description 221mm 30W Clear a unit mm 30W Opal unit mm 60W Clear unit mm 60W Opal unit Internally silvered for increased light output Ideal for low cost display lighting using a 230V supply Description Length Dia. Brand Reflector R50 Spot SES 40 R50 spot GE Reflector R64 Spot ES 40 R64 spot GE Reflector R64 Spot ES 60 R64 spot GE Reflector R80 Flood ES 60 R80 flood Osram Description Reflector R50 Spot unit Reflector R64 Spot unit Reflector R64 Spot unit Reflector R80 Flood unit Energy Saving Candle A mains voltage halogen capsule within a traditional candle shaped outer bulb Energy savings of 30% against conventional GLS technology Twice the life of a normal candle lamp Fully dimmable Voltage 230 V Length 104 mm Finish Clear Equivalent 40 W Dia. 35 Description 28W 230V SES Clear Candle unit GLS Pygmy Lamps GLS Pygmy Lamps A selection of pygmy lamps for use where space is limited. Note: The Rough Service pygmy lamp is for use in areas of high vibration and mechanical shock Finish Clear Dia. 29 Voltage (V ac) Length Brand SBC B15d GE BC B22d Osram BC B22d GE SES E GE SES E GE SES E GE ES E Philips SBC B15d unit BC B22d unit BC B22d unit SES E unit SES E unit SES E unit ES E unit Mains Tungsten Halogen Standard Linear Horizontal burning position (for lamps over 750W) Dimmable Life (Hrs) W R7S Lumen Dia. 12 Colour Temature 3050 K Voltage 230 V Length mm Description Brand 230V 1000W GE unit Linear Double Ended 110V linear halogen lamps. Note: Burning position: horizontal ±15 Haloline ECO Linear Halogen Mains Reflectors and sules PAR 38 Low energy consumption Available as a flood or spotlamp Parabolic aluminised reflector Ideal for use with outdoor IP44 spotlights Cool running front face Can be used in GU10 or GZ10 luminaires Life (Hrs) 2000 Dia. 122 ES Voltage (V) 240 Colour temature 2900 K 120 W Length 136 mm Description Intensity (cd) Beam Angle ( ) PAR 38 Flood PAR 38 Spot GU10 Reflector Lamps Similar appearance to low voltage tungsten halogen lamps GU10 base can be used in both GU10 and GZ10 sockets Aluminium reflector Closed face with UV filter Heat is projected forward which reduces heat build up within the luminaire Double fused for added protection R7S Voltage 110 V Length 118 mm 500 W Life (Hrs) 2000 K1 LV UV Stop Yes 500 K1 LV unit Linear halogen ECO lamps use a special infra red reflective coating on the inside of the envelope and a low conductivity xenon gas filler to help reduce heat loss from the filament. These two technologies help to reduce the energy required to maintain filament oating temature. Energy saving 1:1 replacement for standard linear halogen floodlight lamps Average lifetime of approximately 2000 hours Lower thermal output Ideal for emphasising and accentuating the structure of a room Can be used anywhere No transformer required Fully dimmable Note: Enclosed luminaires are required with these halogen floodlight lamps for both indoor and outdoor applications Diameter 12 mm Use in open faced Luminaries No Life (Hrs) 2000 Voltage 230 V Linear Halogen Equivalent Colour Temature (K) Length Lumen R7s R7S R7S Length unit unit unit Description PAR 38 Flood unit PAR 38 Spot unit W Length 53 mm Life (Hrs) 2000 Dia. 51 GU10 50 W Voltage (V) Intensity (cd) Beam Angle ( ) Description Spot unit Flood unit New products available online every week 1127

6 LED Retrofit sule Lamps LED Retrofit G4 sule Lamps LED retrofit replacement for G4 halogen capsule lamps Energy saving and long lamp life Choice of colour temature Choice of G4 pin options: side or rear mounted Note: Indoor use only Approvals: EMC, LVD, RoHS Lamp G4 Dimmable No 1.2 W Ambient Temature Range C Beam Angle 120 Colour temature (K) LED Cluster Lamp Edison Screw (E27) Lamps made up of a cluster of 20 water-clear red LEDS, with a view angle of 120. Available with edison screw or bayonet cap fittings. Supply Vac 230 Oating Temp Deg C Oating Current (ma) 25 Contact type Centre anode 20mA 11000mcd Length 97 mm E27 Diameter unit Bayonet (Ba22) Supply Vac 230 Contact type Non-polar Oating Current (ma) 25 Length 97 mm 20mA 3000mcd Diameter 68.5 Ba22 Colour Red Oating Temp Deg C -10 to unit LED Retrofit Reflector Lamps Parathom GU10 LED Suitable as an energy saving replacement for GU10 mains voltage halogen reflector lamps Up to 15,000 hour lamp life Very low power consumption Ideal for spot lighting Fitted with OSRAM High Power Golden DRAGON LEDs Extremely low UV and IR component Shock and vibration proof Note: Not suitable for use with dimmers Base GU10 Dimmable No 4.5 W Length 56 mm Equivalent 20 W Life (Hrs) Beam Angle 35 Voltage V Diameter 50 mm Description Lumen Output Colour temature (K) a unit a unit a unit a unit a unit a unit W Warm unit White 4.5W Daylight unit LED Replacement for 12V Dichroic Lamps Note: It is strongly recommended that these LED lamps are oated with the dedicated LED driver. In some instances the lamps will run with existing drivers and power supplies, but it is important to ensure that the required minimum wattage is reached. Use with the dedicated LED driver is recommended for greatest longevity and compatibility. The 5W lamps will protrude from most fittings and are therefore unsuitable for enclosed fittings. Lamp life may be reduced if installed in sealed fittings. Suitable as a direct energy saving alternative to 12V MR16 halogen dichroic lamps Comparable light output to higher wattage halogen lamps making them suitable for general lighting, lift cars, hotels and bars as well as accent and highlighting effects Wide beam angle (60 ) for a good even spread of light Long lamp life with very few early failures (if run on the dedicated transformer) making it suitable for difficult to reach locations Available colour outputs: pure white to blend in with other halogen lamps or warm white which provides an eye-pleasing light quality similar to tungsten incandescent lamps Very cool beam and low heat generation reduces air conditioning requirements 1128 Low Voltage ON-LINE Attractive nickel plated diecast housing Dedicated LED driver (Stock Number ) is suitable for use within a luminaire, enclosure or free standing (within ceiling space etc.) and can drive multiple lamps (max. 10 W) Base GU5.3 Life (Hrs) Voltage 12 Vac/dc Diameter 50 mm Beam Angle 60 Base GU5.3 Equivalent Colour temature (K) Length Description 3W (20W equiv), warm white unit W (20W equiv), cool white unit W (35W equiv), warm white unit W (35W equiv), pure white unit Description 10 W LED lamp driver unit MASTER LED Replacement for Mains Reflectors These robust, long life PAR LED retrofit lamps provide a warm white light for general and spot lighting applications. They are especially suitable for public areas such as shops where the light is on continuously. The IP44 rated version (Stock Number ) of the PAR 38 lamp is is one of the few energy saving alternatives to incandescent PAR 38 outdoor lamps available today. Base ES Dimmable No Colour temature 2700 K Voltage 230 V Beam Angle 24 Equivalent Diameter Length Life (Hrs) Description PAR 38 Indoor a unit PAR 38 Outdoor a unit PAR 30 Indoor a unit LED Replacement for Mains Reflector Lamps Suitable for use as an energy saving alternative to many reflector lamps Depending on the fitting, could be a suitable replacement for PAR38, PAR30, PAR20 and R95 lamps Comparable light output to a 50W halogen lamp Suitable for general lighting and accents with a wide 60 degree beam angle Long lamp life making it especially suitable for difficult to reach or high vibration areas Cool white colour light to blend in with other halogen lamps Cool beam and low heat generation reduces air conditioning requirements and also suitable for close working Attractive nickel plated die-cast housing Suitable for use at low tematures (ambient temp range: -30 C to +40 C), however not outdoors or in wash down areas Base ES Dimmable No Colour temature 5300 K Length 100 mm 8 W Life (Hrs) Equivalent 50 W Lumen Output 640 Beam Angle 60 Voltage 230 V Diameter 95 mm Closed Face Voltage UV Stop unit OM = Order Multiple Indicates more pricing available online a New product to range * manufacturers information unavailable at time of printing 12 V Yes Life (Hrs) Beam Angle ( ) LIF Codes ANSI Codes Brand Spot GU4 10 M252 FTB Philips Flood GU4 30 M262 FTD Philips Spot GU4 10 M265 FTE Philips Flood GU4 30 M170 FTH Philips Spot GU M268 ESX GE

7 ORDERLINE Life (Hrs) Beam Angle ( ) LIF Codes ANSI Codes Brand Flood GU M269 BAB GE Spot GU M272 FRB Philips Flood GU M281 FMW GE Dichroic Mirror GU5.3 8 M249 EXT GE Narrow Flood GU M250 EXZ GE Spot GU M258 EXN GE Dichroic Mirror GU M280 FNV GE Spot unit Flood unit Spot unit Flood unit Spot unit Flood unit Spot unit Flood unit Dichroic Mirror unit Narrow Flood unit Spot unit Dichroic Mirror unit Open Face Voltage 12 V Wide Flood Life (Hrs) W GU5.3 Beam Angle 60 Dimension 50 LIF Codes M80 UV Stop Yes ANSI Codes FNV sule unit sule Description Voltage (V) Life (Hrs) (h) Filament angle Brand 10W 6V G4 Axial Osram W 6V G4 Transverse GE W 12V G4 Axial Osram W 12V G4 Axial Osram W 12V G4 Axial Philips W 24V G4 Transverse Philips W 12V GY6.35 Transverse Osram W 12V GY6.35 Transverse Philips W 12V GY6.35 Axial Philips W 12V GY6.35 Axial Philips W 12V GY6.35 Axial Philips W 24V GY6.35 Axial Osram W 12V GY6.35 Axial Philips Description 10W 6V unit W 6V unit W 12V unit W 12V unit W 12V unit W 24V unit W 12V unit W 12V unit W 12V unit W 12V unit W 12V unit W 24V unit W 12V unit Energy Saving Low Voltage Halogen These lamps will directly replace standard low voltage dichroic halogen reflector lamps. An infrared coating on the capsule reflects heat back onto the filament allowing reduced power to produce the same light output Energy saving of upto 40% against standard dichroic lamps Lower heat output increases user comfort and reduces air conditioning demand Lamps are closed faced, suitable for use in open luminaires Note: Electronic transformers have a minimum load which needs to be considered when retrofitting these lamps Diameter 50 mm Life (Hrs) 5000 GU5.3 LIF Codes ANSI Codes Beam Angle ( ) Beam M668 ESX 20 8 Spot M669 BAB Flood M608 * 30 8 Spot M624 * Narrow Flood M636 * Flood M660 * Wide Flood M616 FRB 35 8 Spot M670 FRA Narrow Flood M681 FMW Flood M625 * Wide Flood Beam 20 Spot unit Flood unit Spot unit Narrow Flood unit Flood unit Wide Flood unit Spot unit Narrow Flood unit Flood unit Wide Flood unit Low Pressure SOX Lamps Oating at a wavelength close to the peak sensitivity of the human eye, these Low Pressure Sodium lamps provide the highest luminous efficiency of any general purpose lamp. SOX lamps emit a yellowish-orange light and are consequently only suitable for use where good colour discrimination is not required. They are particularly suitable for use where long oating hours are required. SOX lamps are generally employed in amenity applications, primarily because they are the most efficient light sources available - they deliver more lumens of light for each watt of power consumed than any other type of lamp. Su SOX Clear tubular lamps for use in luminaries fitted with ignitor/ starter circuits Burning position horizontal ±20 Long-life hours rated average life Note: These lamp do NOT have internal ignitors/starters Lamp BY22d Diameter mm 54 Internal Ignitor No Lumen Efficacy (Lm/W) Length mm unit unit Discharge SON Lamps These lamps combine high efficiency and long life with an improvement in colour appearance and rendering compared with low pressure lamps. SON lamps emit a golden-white light. The SON-T lamp, with its clear tubular outer envelope, lends itself to applications that demand precise optical control, e.g. floodlighting. The SON-E lamp, with its elliptical glass bulb, inside which a white diffusing coating is applied, suits other applications where such accuracy of light control is not so essential. An ignitor (internal or external) is used to supply the high voltage necessary for lamp strike up. Reliable strike up (when hot, less than 60 seconds) thus is ensured, and a simple choke is used to stop excessive voltage rise. The run-up time can be up to 6 minutes when cold. Tubular SON-T Very good efficiency, low colour rendering, typically Ra20-39 Twin Arc versions greatly extend lamp life and allow for hot re-strike after power failure SON-T Plus offers 20% greater lumen output and longer lamp life Lamp Finish Internal Ignitor Clear No Luminous Efficacy Length Dia. Brand 70 ES E27 SON-T Osram ES E40 SON-T Osram ES E40 SON-T PIA Plus Philips ES E40 SON-T Osram ES E40 SON-T PIA Plus Philips ES E40 SON-T PIA Plus Philips Lumen unit unit unit unit unit unit Many more leading brands from over 2,500 suppliers available online 1129

8 Tubular High Pressure SON-T Clear tubular high pressure SON lamps suitable for use in either open or enclosed luminaires. Universal orientation Note: Requires HPS ballast and ignitor SON-T Colour temature 2000 K Shape Tubular Lamp Finish Clear Internal Ignitor No Mounting Orientation Universal Colour Rendering 25 E40 Diameter Lamp life (hrs) Length Lumen a unit a unit a unit Elliptical SON-E Elliptical style lamps with diffuse finish Internal Ignitor types available Lucalox versions have an amalgam reservoir which slows the rise in tube voltage, a chief cause of lamp failure SON-E Shatteproof versions are suitable for food preparation areas etc., and are FDA approved SON-E Twin Arc versions greatly extend lamp life and allow for hot re-strike after power failure Lamp Finish Diffused Lumen Luminous Efficacy Internal Ignitor Length Dia. 70 E27 SON-E * 83 No E40 SON-E * 104 No E40 SON-E * 119 No E27 High Pressure Sodium Yes Brand OSRAM unit OSRAM unit Osram unit Philips unit Metal Halide These lamps produce a clear white light and are suitable for display or floodlighting, where the heat output from tungsten halogen lamps would create a problem. Metal Halide Lamps have an efficiency approx. 4 times higher than halogen lamps and xenon lamps. In addition, the short-arc type is similar to a point light source, making optical design easy. As their colour temature characteristics are similar to daylight colour, exact colours (RGB) can be reproduced. They can also be used for both high bay and low bay applications.,compared to High Pressure Mercury lamps, Metal Halide lamps offer greater efficiencies and, compared to high pressure sodium (SON) lamps, they have similar advantages, but have different output characteristics. A disadvantage of metal halide lamps, when compared to SON lamps, is that they have a shorter service life. Tubular Single ended, clear tubular Powerstar Lamps Suitable for low bay lighting in fittings with ignitor/ starter circuits Note: These lamps require 2 to 10 minutes to cool before re-striking, but shorter times are possible if installed in fittings with high voltage ignitor circuits. Care must be taken NOT to touch the glass surface of the lamp during installation. Lamp GES (E40) Lumen Lumen efficacy Colour Temature (K) Length Diameter Lm/W Lm/W unit unit Tubular - White-Lux Plus for SON/HPS Ballasts White-Lux Plus metal halide lamps can be used to convert the yellow light of sodium lamps in existing SON ballasted installations to clean white metal halide light. Oate on standard HPS ballasts and ignitors Formed body arc tube for fast starting Open and Enclosed versions available - please see "Fitting " HIT Lamp Finish Clear Colour temature 4000 K Shape Tubular Internal Ignitor No Lumen Colour Rendering Diameter Lamp life (hrs) Length Mounting Orientation hours 156 Universal hours 225 Universal hours 285 Universal hours 211 Horizontal ± Mercury ON-LINE Elliptical Shatterproof - Glass Guard Metal halide lamps using shatter resistant GlassGuard coating technology.glassguard coatings prevent widespread glass contamination by completely retaining fragments from broken or shattered lamps. The 200 W and 350 W lamps are energy saving, and provide an equivalent light output to the 250 W and 400 W lamps respectively. Ballast change is required when changing lamp wattage. Shatterproof metal halide lamps DuPont Teflon G fluropolymer coating Coating also provides good thermal resistance and excellent light transmission Linear Compact Metal Halide Lamps Double ended clear white light output Ideal for display/floodlighting Designed for use with ignitor/starter circuits Note: These lamps require 2 to 10 minutes to cool before re-striking, but shorter times are possible if installed in fittings with high voltage ignitor circuits. Care must be taken NOT to touch the glass surface of the lamp during installation. 70 W Colour temature 3000 K Lamp Rx7S Length mm Lumen 5000 Diameter 20 Lumen efficacy 72 Lm/W unit Linear Linear double-ended lamp, with a clear UV - block quartz outer envelope Suitable for use in floodlights, downlights and uplights, when used with appropriate gear, and in luminaires with a protective front glass Note: These lamps require 2 to 10 minutes to cool before re-striking, but shorter times are possible if installed in fittings with high voltage ignitor circuits. Care must be taken NOT to touch the glass surface of the lamp during installation. Lamp R7s Colour Temature 4200 K 150 W Length 135 mm Lumen Diameter 30 Lumen efficacy 81 Lm/W Elliptical Fitting 70 ES E27 Enclosed a unit GES E40 Enclosed a unit GES E40 Enclosed a unit GES E40 Open/ enclosed a unit HIPE Shatterproof Fitting Open/enclosed GES E40 Internal Ignitor No Colour temature 4000 K Lamp Finish Shatterproof Colour Rendering 65 Shape Elliptical Lumen Diameter Lamp life (hrs) Length Mounting Orientation Vertical ± Base up ± Vertical ± Vertical ± Lumen a unit a unit a unit a unit unit These lamps are used in some industrial and warehousing applications. They are not as efficient as their alternatives, but their use may be dictated by colour rendering requirements. The lamps require only a ballast for additional control. The ovoid glass bulb type has an internal phosphor coating, which converts the UV elements in warm light, and has a universal burn position. Control gear oated, ES or GES cap elliptical MBF (HPL- N) lamps Inside surfaces coated with europium-activated yttrium vanadate phosphor to produce a cool white light They are an acceptable alternative to fluorescent lighting Diffuse lamp finish Lamp Lumen Efficacy Colour Temature Length Diameter efficacy (K) 80 ES 3700 Lm/W ES 6300 Lm/W OM = Order Multiple a New product to range * manufacturers information unavailable at time of printing

9 ORDERLINE Lamp Lumen efficacy Efficacy Colour Temature (K) Length Diameter 250 GES Lm/W GES Lm/W unit unit unit unit Ceramic Metal Halide CDM-T Single Ended These lamps are single ended with a G12 ceramic 2 pin base. The Elite versions of the lamps have a improved colour rendering and higher efficacy. Note: Must be used in combination with a ballast and an ignitor. G12 Diameter 20 Colour temature 3000 K Lamp Finish Clear Description Lumen Colour Rendering Length Lumen efficacy CDM-T 35W Lm/W CDM-T Elite 35W Lm/W CDM-T 70W Lm/W CDM-T 70W (12- pack) Lm/W CDM-T Elite 70W Lm/W CDM-T 150W Lm/W CDM-T 150W (12- pack) Lm/W Description CDM-T 35W unit CDM-T Elite 35W unit CDM-T 70W unit CDM-T 70W (12-pack) unit CDM-T Elite 70W unit CDM-T 150W unit CDM-T 150W (12-pack) unit CDM-TC Single Ended sule These lamps are single ended, capsule style with a 2 pin base. The Elite versions of the lamps have a improved colour rendering and higher efficacy. G8.5 Lamp Finish Clear Colour temature 3000 K Length 85 mm Diameter 15 Lumen Colour Rendering Lumen efficacy CDM-TC Lm/W CDM-TC Elite Lm/W CDM-TC Lm/W CDM-TC Elite Lm/W CDM-TC unit CDM-TC Elite unit CDM-TC unit CDM-TC Elite unit CDM-TD Double Ended These lamps are double ended with a RX7s cap. CDM-TD Internal Ignitor No RX7s Lamp Finish Clear Colour temature 3000 K Lumen Colour Rendering Diameter Length Lumen efficacy * Lm/W Lm/W Lm/W * Lm/W unit unit unit unit Ultraviolet Lamps UV Tube, Black Light Blue Black light lamps which emit near UV rays at 315 to 400nm with strong photochemical and fluorescent effects Suitable for display, theatrical and security applications Peak wavelength 370nm Lamp life (hrs) Length 6 G T G T G T unit unit unit Tubes for Insect Killers "05" colour UV tubes commonly used as an attractant in insect killers but other applications can include diazo copying and some use in some photochemical reactions. Available in linear, circular, U bend and tight U bend formats Description Dimension Description Dimension 15 Standard insect killer tube 15W 450(L) Standard insect killer tube 15W Circular Ø 210 Standard Ø Narrow U tube (L)240 Narrow U tube (L) Product Description Standard insect killer tube 15W unit Circular unit Narrow U tube unit Special Purpose Automotive Halogen Headlight ECE Category BS ref. / Base Voltage (Vdc) Drawing Figure H1 4 P14.5s H3 453 PK22s H4 472 P43t H3 460 PK22s Description H1 12V 55W halogen bulb unit V 55W H unit V 60/55W H unit V 70W H unit Instrument Panels / Interior Light ECE Category / Base C5W SV8.5-8 BS ref. Voltage (Vdc) BS ref unit unit unit unit Visit our website for additional price information and exciting promotions 1131

10 12 & 24V Vehicle Lamps ON-LINE Description 250W, 24V OHP Lamp unit W, 24V OHP Lamp unit W, 12V OHP Lamp unit W, 12V OHP Lamp unit W, 15V OHP Lamp unit W, 36V OHP Lamp unit sule GY9 5 cap Note: "s" and "d" in the / Base information denotes single pip and double pip contacts respectively. Description ECE Category BS ref. / Base Voltage (Vdc) Drawing Figure 12V 4W Side/parking T4W BA9s V 5W Side/parking R5W BA15s V 10W Tail R10W BA15s BA15s 12V 21W P21W BA15s BA15d bulb 12V 21W P21W BA15d V 21W / 5W Stop & Tail dual element P21/5W W; 5 BAY15d V 4W Side/parking T4W BA9s V 5W Side/parking R5W BA15s V 5W Side/parking R5W BA15d V 21W Indicator/stop P21W BA15s BA15d bulb 24V 21W P21W BA15d Description 12V 4W Side/parking unit V 5W Side/parking unit V 10W Tail unit BA15s 12V 21W unit BA15d bulb 12V 21W unit V 21W / 5W Stop & Tail dual unit element 24V 4W Side/parking unit V 5W Side/parking unit V 5W Side/parking unit V 21W Indicator/stop unit BA15d bulb 24V 21W unit Projector Dichroic Voltage (V) LIF Codes ANSI Codes Brand FLT FLT GZ4 GE ND3 EPZ GX5.4 Philips A1/230 EFN GZ6.35 Philips A1/231 EFP GZ6.35 Philips A1/232 EFR GZ6.35 Philips A1/259 ELC GX5.3 GE ELH ELH GY5.3 Philips unit unit unit unit unit unit unit sule Description Voltage (V) LIF Codes ANSI Codes 250W, 24V OHP Lamp A1/223 EHJ G W, 24V OHP Lamp A1/216 FCS G W, 12V OHP Lamp A1/220 BRL G W, 12V OHP Lamp A1/215 FCR GZ W, 15V OHP Lamp A1/234 BRJ/EVB G W, 36V OHP Lamp A1/239 EVD GY OM = Order Multiple a New product to range GY9.5 Voltage (V) LIF Codes ANSI Codes A1/262 DZE/FDS A1/233 DYR Voltage (V) unit unit Ceramic Metal Halide Compact Reflector A compact metal halide lamp with integral reflector for use in projection, fibre optic and architectural lighting application Minimal forward UV-radiation Note: This lamp requires a ballast and ignitor for correct oation. ANSI Codes CDM-SA/R 150 W Ceramic metal halide Special Purpose IR Heat Lamps Tungsten Filament a unit Highly efficient, instant response tungsten filament lamps, with a life expectancy of 5000 hours (avg.) Hard pressed: these have an all round reflector, which directs more heat into the beam, and enables them to replace higher wattage blown types Hard blown: suitable for all applications Voltage 240/250 V Lamp life (hrs) 5000 E27 Colour Temature 2400 K Glass type Diameter Length 100 Hard Pressed Hard Pressed Hard Blown Glass type 100 Hard Pressed unit Hard Pressed unit Hard Blown unit Special Purpose High Efficiency Solar / Automotive Lamps Highly efficient and bright solar / automotive lights suitable for use with 4 pin L type compact fluorescent lamps. Available for both 12 and 24 Vdc supplies. Ideal for connection to DC vehicle power and to batteries charged by solar panels. High frequency electronic control gear built in, ensures maximum lamp life (approx hours) and energy efficient oation Low energy consumption Minimum battery drain On / off switch White ABS enclosure Suitable for positive or negative earth vehicles 350 mm x 80 mm x 50 mm Weight: 0.3 Kg Both the 7-11W luminaires (12V and 24V ) will oate with 7W ; 9W or 11W 2G7 S type CFL lamps such as , or respectively. The 18W luminaires (12V and 24V ) oate with 18W 2G11 L type CFL lamps, such as Lamps are not supplied with the luminaires Tube 4 pin L type CFL Oating Temature C Dimensions L 350 x W 80 x D 50 mm 7; 9; 11 W Description Lumina7 12V a unit Lumina7 24V a unit

11 ORDERLINE Automotive Fluorescent Fitting Slimline fluorescent fitting Opal shade Minimum battery drain Pushbutton On/Off switch Suitable for positive or negative earth vehicles Description 300 mm 5000 K clear unit Transparent 400 mm 5000 K unit mm 5000 K clear unit mm 5000 K clear unit mm 7500 K clear unit mm 7500 K clear unit Description FL 8 W 300 mm T5 linear unit Low Voltage Bulkhead 3 point fixing gives stability on uneven surfaces Polycarbonate construction Rounded corners to reduce the risk of injury Side position rocker On/Off switch Polarity protected Marine or vehicle use 16 W Width 160 mm Tubes Single 2D (4pin) Depth 46 mm Lamp Supplied Yes Supply Voltage (Vdc) 24 Oating Temature C Supply Current Amps 0.6 Length 160 mm Harsh Environment Tufflite Anti-Corrosion Fitting Scott lamp unit Protected to IP65 for use in areas of high humidity or corrosive environments Glass reinforced polyester moulded body and acrylic diffuser for strength Blanked 20mm cable entry at both ends allows through wiring, (sealing washer kit supplied) White stove enamel reflector/gear tray with power factor corrected switch start control gear Gear tray retained by turnbuckles and hangs on straps 3 way main terminal block accepts 2 X 2.5mm 2 conductors Supplied with hinged polycarbonate latches, these can be changed for the stainless steel clips (available separately) for use in food factory applications etc. Lamps not supplied 230Vac Lamp T8 18W Width single/twin 124 / 194 Length / depth 666 / 108 Weight (kg) 1.9 / 2.2 Fixing centres 230 Manu Part No TDA21S & TDA22S Description 1 x 18W x 600mm Lg unit x 18W x 600mm Lg unit LED Mains Strip Light Link cables and AC power lead compatible with linkable LED mains striplights. Description 250-mm link cable unit mm link cable unit m wire-ended AC power lead unit Stand Alone Spotlight Surface mounting Cast alloy and pressed steel Safety extra low voltage (SELV) 350 head rotation 90 movement either side of vertical Supply Voltage (Vac) 12 Height W Width mm 60 Lamp Dichroic GU5.3 Length mm 60 Lamp Supplied No Transformer / Spotlight IP55 rated Die cast aluminum construction 360 head rotation 70mm dia. Raised or lowered 112 Integral mains transformer Suitable for 20W or 50W lamps Supply Voltage (Vac) 230 Height W Width mm 70 Lamp Dichroic GU5.3 Length mm 196 Lamp Supplied No unit Acrylic Tube Light Internal high frequency control gear eliminates flicker and reduces oating tematures 70mm dia. acrylic tube, 5mm thick, provides good impact protection and UV stability Glass fibre reinforced polyamide End caps can be easily removed for lamp changing then resealed by hand Plug in electrical terminals Slide out gear tray allow easy removal for lamp changing etc. Supplied without lamps Mounting Bracket (stock no ) available separately IP Rating IP67 Tubes 1xPL-L Oating Temp Range degc Length mm W Supply Voltage (Vac) Description 24W 230V PL-L louvre a unit W 230V PL-L a unit Display LED Mains Strip Light Ultra-slim, low profile, linkable, low power LED strip lighting available as a direct replacement for existing T4 fluorescent lighting. Low power consumption Up to 10 years continuous oation Cool running Integral on/off switch Internal fuse protection Easily "daisy chained" together using link cables (available separately, see Note) Note: All strip lights require the AC power lead Optional 250mm, 500mm & 1000mm link cables , & respectively (available separately) Supplied with: a choice of nylon mounting brackets and 2 screws New products available online every week Description White Transformer / Spotlight unit Black Transformer / Spotlight unit Low Voltage Transformers Dimming Methods:,Leading Edge:,The control device is either a thyristor or triac which blocks power until they are,switched on by the control signal, at which time the current flows almost,instantaneously, and continues to flow until the end of the half cycle of the mains,waveform. When the signal reaches zero, the device turns off and no more,current is passed until it is triggered again. Turning the power on and off in this,manner averages out, creating a constant intensity level and by altering the,precise trigger point over a iod of time the lamp can be dimmed.,trailing Edge:,Since this method of dimming uses transistor technology it is not limited to just,switching, therefore current can be controlled gradually. Transistors can be,programmed to pass current at the start of each half cycle, and gradually switch,off later. This will control the full amount of power reaching the lamp without the,side effects of a step increase in current. GET Dimmable Electronic Transformers Compact lightweight electronic transformers for low voltage (12Va.c.) lighting applications. One primary winding and one secondary winding Dimmable Short circuit protection Over temature protection 60VA & 105VA 20cm cable termination 150VA & 200VA have screw terminals Input Voltage 230 / 240 V ac Output Voltage 11.6 V ac VA Rating (VA) Dimensions (L x W x H) x 40 x x 40 x 30 mm x 56 x x 56 x 44 mm VA Rating (VA) unit unit

12 ON-LINE VA Rating (VA) unit unit Floodlighting Galaxy Tough impact resistant UV stabilised polycarbonate body and visor Specular anodised aluminium reflector Hinged cover with retained screws Toughened glass front which hinges down for easy relamping 70 W Height 322 Lamp SON-E Width 300 IP Rating IP65 Depth 190 Ambient Temature Range C -25 to +40 Darksky Low glare and cut-off light distribution stops light spill Designed to be mounted with the glass horizontal but, can be inclined up to 20 without any upward light Inclinometer included for easy adjustment Black powder coated, diecast aluminium body Toughened soda lime glass front on a hinged cover High purity, high reflectance aluminium reflector Asymmetric light distribution gives even coverage Can be wired without removing the reflector Lamp SON-T Width 440 IP Rating IP65 Depth 155 Height 415 (max) unit unit Pre-Wired General purpose SON floodlight Symmetrical beam pattern Pre-wired onto a connection box which is suitable for through wiring for easier installation Fitted mounting bracket Description 400W SON-T unit Halogen unit Description 70W SON E-I unit Brilliant white light and no warm-up time No need for ballast or ignitor circuits Die-cast aluminium body Epoxy matt black finish Hinged toughened glass lens sealed with a silicone rubber gasket Dimpled anodised aluminium reflector provides a wide spread of light Note: Halogen lamps not supplied, please refer to the following stock numbers: (300W equiv); (500W equiv) etc. (max) 300 / 500 W Supply Voltage (Vac) 230 Lamp Halogen Height 170 Lamp Supplied No Width 200 IP Rating 44 Depth 190 Ambient Temature Range C Weight 1.1 kg unit PIR Switched Detection range up to 12m On-time selectable between 5 seconds to 12 minutes Photocell prevents daylight oation Day/night light level sensitivity adjustment Zinc alloy construction Fully enclosed floodlight Lamps supplied (type R7s) Note: To override the PIR oation in order to oate the floodlight continuously, regardless of motion, turn the power supply to the floodlight off and then back on within 2 seconds. To return to automatic oation, turn the power supply to the floodlight off for at least 10 seconds and then turn it back on. Lamp Supplied Yes Ambient Temature Range C Lamp Halogen Supply Voltage (Vac) 230 V ac IP Rating 44 Description (max) Height Width Depth Weight (kg) PIR Switched Halogen 150 W PIR Switched Halogen 500 W (max) unit unit Solar Mate Secure Professional PIR Security Light The Solar Mate Secure Professional is the ultimate PIR, movement activated security light. Designed for busy locations such as public passage ways, driveways, and frequently used steps. Using a powerful 2.5 Watt solar panel and ultra bright 45 LED light unit ensures the Professional is capable of illuminating an area usually only covered by a mains halogen light.,its integrated PIR movement sensor can be adjusted both for sensitivity and time. Installed in minutes 10V 2.5W single crystal silicon solar panel 7.4V 3000mAh lithium polymer battery (supplied) Light unit contains 45 white LEDs and PIR 4.5m connecting cable joins the light unit to the solar panel Wall fixings included Note: Full fitting instructions are included Supplied with: Connection cable, wall fixings, lithium polymer battery pack, solar panel Exterior Amenity Bulkheads General Purpose SON Indoor or outdoor use Die cast aluminium alloy body Textured grey powder coat finish Impact resistant polycarbonate cover Frame is hinged on a stainless steel pin and fastened to the body by 4 captive stainless steel screws Top and bottom entry for 20mm conduit (1 entry is plugged) max 70 W Supply Voltage (Vac) 230 Lamp SON-E Height 318 Lamp Supplied No Width 210 IP Rating IP65 Depth 175 Ambient Temature Range C -20 to +40 Weight 5.2 kg SON Downlighter Die cast aluminium alloy body Textured black powder coated frame Impact resistant polycarbonate cover Four captive steel screws secure frame to body Cover hinges down for lamp replacement Body tapped both ends for 20mm conduit entry BESA box mounting max 70 W Supply Voltage (Vac) 230 Lamp SON-E Height 210 Lamp Supplied No Width 318 IP Rating IP65 Depth 180 Ambient Temature Range C -20 to +40 Weight 5.7 kg a unit unit Square 2D unit Description 70W SON E-I unit Vandal resistant BS4533 compliant Die-cast aluminium body Black powder coat finish Clear polycarbonate cover which hinges down Rear fixing via 4 7mm knockouts or BESA box fitting (sealing washer supplied) Supplied with captive stainless steel tam resist screws and key max 28 W Supply Voltage (Vac) 230 Lamp 2D 4-Pin Height 270 Lamp Supplied Yes Width 270 IP Rating IP65 Depth 104 Ambient Temature Range C 0 to +40 Weight 3.12 kg unit OM = Order Multiple a New product to range

13 ORDERLINE GLS Bulkhead Porcelain BC (B22) lampholder Suitable for lamps up to 100W (max.) Supplied with: security fixing screws and key for the cover, and heat resistant sleeving for incoming mains wiring Note: Version with red lens currently unavailable max 100 W Supply Voltage (Vac) 230 Lamp BC (B22) Depth 100 Lamp Supplied No Width 120 IP Rating IP64 Length 245 Ambient Temature Range C -20 to +35 Low Energy Fluorescent Bulkheads Cost effective for continuous oation Single or dual 9W PL lamp versions Low heat generation and long life Aluminium body with clear polycarbonate lens 20mm conduit knockouts for side and bottom cable entry Supplied with: either 1 or 2 9W compact fluorescent lamps Lamp SL 2-Pin Supply Voltage (Vac) 230 Lamp Supplied Yes Depth 100 IP Rating IP64 Width 120 Ambient Temature Range C -10 to +35 Length 245 Description (max) Fluorescent Bulkhead 9W Fluorescent Bulkhead 2x 9W Emergency Light Fittings There are two basic types of emergency lighting luminaires - maintained and nonmaintained.,maintained,these luminaires have the advantage of being able to be switched between the maintained function (lamp illuminated at all times) and non-maintained (lamp off until power supply fails), making them ideal for applications such as corridors, workshops and manently illuminated emergency exit signs.the maintained luminaires also have the facility of being switched in banks of up to ten units.,non-maintained,these luminaires are only illuminated on a failure of the mains supply. Ideal for emergency exits, switchrooms and storage areas. Weather and Vandal Resistant 3 hours of emergency light output at 50 lumens 20mm knockouts at both ends and rear BESA box mounting Supply voltage 230VAC 50Hz 0 to +49 C oating temature range Polycarbonate with a white base and opal diffuser For suitable T5 8 Watt tube (not supplied) see W Lumen Output 50 IP Rating IP65 Length 370 mm Lamp T5 Fluorescent Width 140 mm Lamp Supplied No Depth 101 mm Weatherlite Designed for external use Self-extinguishing, vandal resistant polycarbonate Ni-Cd batteries provide 3 hrs illumination LED indication of battery charging Plug-in gear tray easily removed Conduit and BESA entries moulded and centred for drilling Opal diffuser 8 W Lumen Output 180 IP Rating IP65 Length 125 mm Lamp T5 Fluorescent Width 365 mm Lamp Supplied Yes Depth 35 mm Maintained / non maintained 1x unit x unit Non Maintained unit Maintained unit Maintained / non maintained Maintained unit Non Maintained unit unit Description FL 8 W 300 mm T5 linear unit Description FL 8 W 300 mm T5 linear unit Compact 8W Reticulated diffuser provides good light dission in an attractive, impact-resistant design Red LED charge monitor is visible through a diffuser 8 W Lumen Output 50 IP Rating IP65 Length 365 mm Lamp T5 Fluorescent Width 140 mm Lamp Supplied Yes Depth 90 mm LED Recessed Emergency Emergency Twinspot Moulded fire retardant Noryl case Switch for testing emergency mode Battery cut-off prevents deep discharge LED indication of battery charge status Supplied with full instructions Emergency Spotlights Maintained / non maintained Non Maintained unit Maintained unit Description FL 8 W 300 mm T5 linear unit White diecast fitting designed to blend in with GU10 or Dichroic downlights 3 x 1W LED s with controller give wide beam spread (1.8m at 2.5m ceiling height) Fitting also needs either a 3 hour emergency or mains control gear pack Control gear packs are capable of running 1 or 2 fittings Emergency can be run as maintained or non-maintained White LED Downlight Depth 40 1 W Diameter unit Description Emergency Control Gear for LED unit Downlights Mains Control Gear for LED Downlights unit Maintained No Lamp Supplied Yes IP Rating IP20 Length 524 mm 12 W Depth 136 mm Lamp Tungsten Halogen Width 134 mm unit Optional - Switch for testing emergency mode Powered by 2 x 6V 12Ah batteries (not supplied) Battery cut-off prevents deep discharge LED indication of battery charge status Alarm output contacts (0 1A max.) Supplied with full instructions Note: For suitable batteries, please refer to stock no Replacement lamps are available for earlier versions using MBC fittings (see stock no ). Maintained No Length 350 mm IP Rating IP20 Depth 115 mm Lamp Tungsten Halogen Width 300 mm Lamp Supplied Yes Many more leading brands from over 2,500 suppliers available online 1135

14 Exit Routes and Route Guides Slimline LED Exit Sign A very slim exit sign making it suitable for a wide range of applications Long life LEDs with a rated life of 90,000 hours Edge lit panel for even illumination Maintained / non maintained Maintained Lamp LED Duration 3 h Lamp Supplied Yes Mounting Wall unit Hanging LED Exit Sign Swivel mounting bracket allows installation on ceiling or wall Slim unobrtusive design with chrome finish Lifetime LEDs reduce maintenance 30 metre viewing distance Can be used as a single or double sided sign Note: legend panel must be ordered separately see stock no , Lamp Supplied Lumen Output Conversion Kits unit unit Description Maintained / non maintained Duration Mounting Lamp LED chrome exit sign Maintained 3 h ceiling / wall LED Down arrow legend Left / right arrow legend Charger/inverter modules for converting fluorescent luminaires into emergency lighting units.,the module and battery packs fit inside most modern fluorescent batten fittings. For luminaires that have limited internal dimensions or that have internal tematures above 50 C, remote mounting boxes are also available. The remote box is also suitable for converting double luminaires into emergency units, however only 1 tube will oate under emergency conditions. Two live supplies are required for standard oation, one switched, one unswitched. Failure of the unswitched supply oates the changeover circuit bringing on the battery supply. A red LED is supplied with the module for fitting into either the luminaire or remote box, to indicate a healthy battery charging state. The nickel-cadmium battery packs are protected against deep discharge. Emergency Kits Ideal for integrating into existing control gear. Supplied with a fused terminal block and pre-cut connection wires.,the modules can be tuned specifically to the lamp, giving better formance for the cell capacity. Note: Nominal tube diameter - T5=16mm, T8=26mm, T12=38mm Lamp compatibility/ballast Lumen Factor Stock No. T5 T8 2-D PL-L PL-C PL-S / / / / / / / / / / / / / / / / / / / / / 0.09 Note: /Ballast Lumen Factor shown for applicable lamp sizes No. of Cells W Yes Hazardous Area Zone 1 & 2 Ex-e Uses twin T8 linear fluorescent tubes Easy installation Suitable for offshore environments Hinged access to terminal compartment with 6mm terminals at both ends allowing through wiring Integral switch isolates the lamps when cover is removed High frequency electronic ballast Smooth outer surface for easier cleaning Lightweight polycarbonate and GRP housing Group & Category: II 2 G EX eds IIC T4 for Zones 1 & 2 Certificate No.: PTB 96 ATEX 2144 Petrel 7 series, Zone 1 & 2 GLS Bulkhead, Zone 1 E27 lamp fitting allows easy lamp replacement GLS lamps up to 200W or 25W SL fluorescent Can be adjusted from narrow to wide beam Oating temature range -20 C to +33 C Corrosion resistant light alloy body, grade LM25 Group & Category: II 2 G EEx de II B or II C T3 to T6 Certificate No.: SIRA 01 ATEX 1047 Bulkhead, Zone 2 A flameproof bulkhead designed for general lighting Low projection allows use in narrow corridors and low ceiling areas 1 M20 ISO (plugged) cable entries Light alloy body with fresnel glass diffuser Group & Category: II 3 GD EEx nc T3 Certificate No.: 03ATEXTF457/01 ON-LINE Class T4 IP Rating 66 Height 130 mm Supply Vac Lamp 18 W T8 x 2 Width Length Weight (kg) HF control gear for improved lamp life, flicker free starting and lower running costs (not 8W emergency unit) End plates unscrew allowing gear tray removal for ease of maintenance Horizontal or vertical mounting via 2 M8 tapped holes at each end Polycarbonate with adonised light alloy body Compact fluorescent version provides very high light output from a compact unit Suitable for emergency lighting use, maintained and non-maintained Emergency version is 8W sustained for 3 hours Group & Category: II 2 G EEx d IIB & IIC T4-T5-T6 Certificate No.: SIRA 01 ATEX 1033X Class T4 Height 158 mm Dia. 140 IP Rating 66 Supply Vac 240 Brand Petrel Length 752 mm Weight 6.5 kg Lamp Twin Fluorescent 18 W Description Petrel 7 Series Zone 1 & unit Description LED chrome exit sign unit Down arrow legend unit Left / right arrow legend unit Description 10W Tungsten Halogen (MBC) unit Old Style 20W Tungsten Halogen (MBC) unit Old Style Sealed lead acid battery 12V 6Ah unit BA15s 12V 21W unit V 10W Tail unit Length unit unit Class T4 Lamp GLS ES; SL Height 328 mm 200; 50 W Width 270 mm IP Rating 66 Length 196 mm Supply Vac 240 Weight 10 kg Class T3 Lamp GLS (ES); SL Height 305 mm 150 W Width 186 mm IP Rating 68 Length 156 mm Supply Vac 230 Weight 9 kg Petrel Petrel unit Petrel unit unit OM = Order Multiple Indicates more pricing available online * manufacturers information unavailable at time of printing

15 ORDERLINE Ballasts, Ignitors & Starters A range of lighting components for use in self-assembly lighting systems or as replacement components in existing luminaires. The range includes high efficiency ballasts together with a range of lamp, tube and starter holders. Power factor correction is provided by the RS range of lighting capacitors. The range has been designed with ease of assemby in mind as all connections are via push-on grab terminals. For suitable tube and capacitor clips refer to the coated spring clips in the Fasteners/Fixings section. Switch Start Ballasts (Chokes) For use with linear, compact fluorescent and 2D lamps Compatible lamps for switch start ballasts Nominal Linear Compact Fluorescent 2D Lamps PL-S PL-C PL-L 8W 4W, 6W, 8W, 2 4W 11W 5W, 7W, 9W, 11W 10W 13W 13W, 2 6W, 2 8W 5W, 7W, 9W 8W, 10W, 13W 16W 2 7W, 2 9W 16W 18W 18W, 20W, 22W 26W 18W, 24W 18W 21W, 28W 30W 30W, 2 15W 24W, 30W 36W 36W, 2 18W, 40W, 2 20W 36W, 2 18W 36W, 40W 38W 58W 58W, 65W 70W 70W, 75W Number of Lamps 1 Oating Temp. Range ( C) +130 max Fixed O/P or Dimming Fixed Supply Voltage ac 240 Electromagnetic, Fixed Width 41 mm Frequency khz 50Hz Height 32 mm Length Fixing Centres Compatible Lamps Linear 8W 4/6/8W unit W * unit W 2x6/2x8/13W unit W * unit W 18 W unit W 24/30W unit W 36/40W unit High Frequency Ballasts Auto shut down on defective lamps Eliminates stroboscopic effects Low heat generation Silent oation No prolonged flickering Lamp start within 1.5 seconds Compatible Lamps T8 Linear Height 28 mm Fixed O/P or Dimming Fixed Fixing Centres 220 mm Electronic, HF Fixed Frequency khz 40 Supply Voltage ac Number of Lamps Linear Oating Temp. Range ( C) Length Width 1 18 W W W W W W Linear 18 W unit W unit W unit W unit W unit W unit SON/Metal Halide Ballasts designed for use with high pressure sodium (SON) and metal halide lamps of W rating Note: See later in this section for suitable ignitors necessary to strike sodium/metal halide lamps. NOT suitable for use with lamps that have integral control gear. Number of Lamps 1 Electromagnetic, Fixed Oating Temp. Range ( C) 0 to +75 Supply Voltage ac Output Frequency 0.05 khz Line Frequency 50 Hz Compatible Lamps SON/Metal Halide Fluorescent Lamp Starters Two styles available, electronic and glow Glow type incorporates an RF suppressor Electronic type has built in failed lamp shut down safety circuit Flicker free electronic start All starters rated at 230Vac except series type which are rated at 110Vac Note: Series type are rated at 110Vac and should only be used in 230Vac circuits when two lamps are series connected Fluorescent Lamp Starters - Clipsal Clipsal conventional "glow" type fluorescent lamp starters that meet Australian and New Zealand electrical standards. Standards: AS3138 Ignitors Suitable for use with high intensity ballasts, such as those used with SON, SOX, SOXE and metal halide lamps SON ignitors incorporate a timer to switch off the ignitor ciruit should the lamp fail HID Length Width Height Fixing Centres HID unit unit unit unit Dia Length 35 mm Pin Pitch 12.7 mm Compatible Lamps Linear Style Lamp Range Failed Lamp Shutdown Time Supply Voltage ac Number of Lamps Brand Glow Osram Electronic secs RS Electronic, Series secs RS Electronic secs RS Style Glow unit Electronic unit Electronic, Series unit Electronic unit Description Glow Starter, 4-20W unit Glow Starter, 4-65W unit Supply Voltage ac Length 75 mm Number of Lamps 1 Width 40 dia mm Ignitor Description Compatible Lamps High/Low Pres. So./Metal Halide Ignitor SON 35-70W SON Ignitor 35/50/ Ignitor SON/MH W SON or Metal Halide SON 100/150/250/400 Metal Halide 35/70/100/150/250/ 400 Description Ignitor SON 35-70W unit Ignitor SON/MH W unit Visit our website for additional price information and exciting promotions 1137

16 Electromagnetic Ballasts Electromagnetic ballasts for linear and compact fluorescent lamps Vacuum-impregnated with polyester resin Push-in connection terminals for mm 2 wire Conform to EN60920 and EN60921 Ballasts are compliant to Singapore standards T8 Push On Wiring Points Wiring T8 Fluorescent Lamp Holder Bottom Push-wire ON-LINE of ballast Suitable Lamp L7/9/ TC-S L TC-S/TC-D/TC-T/TC-DD/T5 LN TC-D/TC-T L18/ TC-D/TC-T/TC-DD/TC-F/TC-L/T8/T12 L36/ TC-DD/TC-F/TC-L/T8/T12 Manu. Part No. L7/9/ unit L unit LN18I unit L18/ unit L36/ unit ELXc Electronic Range Electronic Warm-start ballasts ELXc ballasts ensure the lamp is started following a defined lamp electrode preheating iod of approx. 1.5 seconds using a fixed ignition voltage. ELXc ballasts should be used for applications with high switching frequencies (e.g. hotels or offices) where energy savings as well as low maintenance costs are desired. Casing Heat Resistant polycarbonate or metal DC Voltage for ignition V Power Factor >0.98 Push-in terminals mm sq. Ambient Temature -20 to 55 C Other specifications RFI suppressed DC Voltage for oation V IP20 protection Manu. Part No. ELXC unit ELXC unit ELXC unit ELXC unit Fluorescent and CFL Lamp Holders T8/T12 Snap-Fit, Back Mount Wiring Points Wiring T8/T12 Fluorescent Lamp Holder Bottom Push-wire unit T8/T12 Snap-Fit, Side Wiring T8/T12 Wiring Points Either side Snap-fit Wiring Push-wire T8/T12 Back Screw Fixing T8/T12 Back screw fixing Wiring Bottom Points Wiring Push-wire unit unit T8/T12 Snap-Fit, Bottom Wiring T8/T12 Wiring Points Bottom Fluorescent Lamp Holder Wiring Push-wire unit Snap-Fit Horizontal or Vertical Mount Starter Holder Starter Holder Wiring Points Either side Starter Holder Wiring Push-wire unit Snap-Fit Starter Lampholder * Wiring Points Either side Snap-fit Wiring Push-wire unit unit Recessed Cage Starter Holder Starter Holder Wiring Points Either side Starter Holder Wiring Push-wire T5 Bottom Wiring T5 Wiring Points Bottom Fluorescent Lamp Holder Wiring Push-wire unit unit OM = Order Multiple * manufacturers information unavailable at time of printing

17 ORDERLINE Screw Mount, Starter Holder Wiring Points Wiring Foot screw fixing Either side Push-wire 180 Shuttered PIR IP44 rated and suitable for use in sheltered outdoor locations Shutters alter detection angle between 180 and 90 in 10 steps Adjustable photocell sensitivity prevents daylight usage Adjustable sensitivity to minimise nuisance tripping Switching Power KW 1 kw Height 100 mm Detection Angle 90 to 180 (10deg steps) Width 85 mm Range (m) 15 Depth 165 mm Daylight override Y Voltage (Vac) 230 Time Delays 5secs to 18min Mounting Wall/Corner Manual Override Y 2G-11 Foot Screw Fixing A separate two-piece cradle support is available with adjustable support height Suitable for use with 2G-11 tubes Mounting Bracket A plated mild steel bracket for end fixing lampholders to a flat surface, provided with round holes for snap-in lampholder fixing.,suitable for use with lampholders , , and Width 35 Fixing Centres 24 mm Height 43 Fixing Holes 2 x 4.3 Screw & Bayonet Lampholders GES E40 Material Porcelain Width 71 mm HID Lamps Yes Fixing Centre 56 mm Fixing Method Bracket Fixing Hole Diameters 2 x 5.2 mm Height 87 mm Ceramic ES E27 Material Porcelain Height mm HID Lamps Yes Width 43 mm GLS Lamps Yes Fixing Centre 18 mm Fixing Method Screw Fixing Hole Diameters 2 x 3.3 mm Plastic ES E27 SES E unit G-11 Wiring Points 2 Compact Fluorescent Lamp Holder Wiring Push-wire unit unit unit unit A moulded E27 lampholder suitable for screw-on, screw-in or snap-in fixing. Two glass reinforced plastic insulation caps are available, a plain cover with an M10 exit thread, and a cover with an integrated cable clamp. VDE approved Material Plastic (black) Height 46 mm HID Lamps No Width 40 mm GLS Lamps Yes Fixing Centre 18 mm Fixing Method Snap fit/screw fit Fixing Hole Diameters 2 x 3.3 mm unit Moulded E14 lampholder suitable for screw-on, snap-in or push-in fixing. A suitable M10 threaded snap-on insulating cover is available Both cover and lampholder are required for oation. Material Plastic Height 45 mm HID Lamps No Width 28 mm GLS Lamps Yes Fixing Centre 14 mm Fixing Method Snap fit/screw fit Fixing Hole Diameters 2 x 2.9 mm unit Security Controllers A modular security system consisting of a zone controller with audible alarm, capable of switching lighting loads. The zone controllers connects directly to PIR movement detectors. BJB BJB BJB unit Halogen Fittings G4, Screw Mount Low voltage, halogen lampholder, rated at 10A,50V The lampholder should be fixed prior to use Cable Length 140 Width 18.6 mm Height 9 mm Fixing Centres 12 x 3.2 mm Depth 18.6 mm Material Steatite/Nickel Silver unit GU5-3, G6.35 Spring Clip Low voltage, halogen lampholder, rated at 10A,50V The entry holes are specially designed to ensure trouble free insertion of the lamp Will also support common G6.35 lamp Cable Length 140 Width 19.2 mm Height 9.4 mm Fixing Centres 12 x 3.2 mm Depth 19.2 mm Material Steatite/Nickel Silver unit Linear, Screw Mount This metal halide lampholder is designed for use with a R7s fitting Rated at 150W, 1000V, 5KV pulse-rated, the holder will accept a starting voltage up to 4 5kV Note: To ensure correct spacing between contacts these lampholders must be fixed prior to use. Cable Length 400 Width 27 mm Height 31 mm Fixing Centres 35 x 4.2 mm Depth 45 mm Material PTFE unit Twin, Screw Mount Twin tungsten halogen lampholder designed for use with a 500W R7s fitting. Rated at 6A, 250V Cable Length 220 Width 137 mm Height 42 mm Fixing Centres 4.2 mm Depth 15 mm Material Steatite/Cop unit Screw Mount This tungsten halogen lampholder is designed for use with a 1000W R7s fitting, rated at 10A, 250V Note: To ensure correct spacing between contacts these lampholders must be fixed prior to use. Cable Length 270 Height 37 mm Depth 35 mm Width 20.5 mm Fixing Centres 28 x 3.3 mm Material Aluminium oxide/brass silver plated unit Daylight Controllers These controllers automatically turn lights ON and OFF in response to changes in ambient light levels, primarily the transition from day to night and vice-versa. The more advanced types (see note below) have inbuilt logic to minimise false triggering, whereas the remainder have inbuilt time delays or higher OFF thresholds, to prevent on/off cycling. As a general rule, these controllers should be sited such that they are not illuminated, by the light they are controlling. Nominal supply voltage is 230Vac.,Note regarding energy-saving negative-hysteresis controllers,where figures for the OFF threshold are lower than for the ON threshold, the sensor is designed such that four thresholds are actually monitored. These are: dusk, the middle of the night, dawn and the middle of the day. Monitoring at times other than dusk and dawn enables the sensor to determine what it should be looking for next, minimising false triggering and improving overall controller oation. New products available online every week 1139

18 2-Part Luminaire Controller Remote IP65 detector Internal mount controller Detector has a 27mm dia. flange, a depth of 25mm and a 20mm thread Supplied with: 2 nitrile gaskets Connection Integral Width 31 mm Height 57 mm Depth 25 mm Detector Switching thresholds (lux) on Integral Luminaire Controller Supplied with 2 nitrile gaskets and 20mm lock ring Switching thresholds (lux) off Output Rating Power Oating Temature ( C) Connection Integral Switching thresholds (lux) on 70 Height 52 mm Switching thresholds (lux) off 35 Width 58 mm Output Rating HPS (SON) 500W, Tungsten 2000W Depth 31 mm Power 0.25 W Detector Photodiode Cd sulphide (5)A Photodiode (5)A 0.25 W Detector Cd sulphide unit Photodiode unit unit Adjustable 1-100Lux Adjustable Lux Rotating front cover sets lux level required Time delay prevents intermittent switching LED indication of unit oation ON-LINE unit Time delay prevents intermittent switching Adjustment by potentiometer Connection Standalone Switching thresholds (lux) on Adjustable Height 91 mm Switching thresholds (lux) off Adjustable Width 91 mm Output Rating Tungsten 1600W, HPS (SON) 200W, Fluorescent 600W Depth 46 mm Power Dia. 46 Oating Temature ( C) Detector Photo resistor unit Connection Standalone Switching thresholds (lux) on Adjustable Height 91 mm Switching thresholds (lux) off Adjustable Width 91 mm Output Rating Tungsten 1600W, HPS (SON) 200W, Fluorescent 600W Depth 46 mm Power Dia. 46 Oating Temature ( C) Detector Photo resistor unit Sensor Head Fitted with a conical, UV stable, impact resistant, translucent cover Omni-directional NEMA connection Replacement for sensors using NEMA Rotaloc Socket Electronic Control Kit (CdS Cell) Fitted with a conical, UV stable, impact resistant, translucent cover Omni-directional Cadmium sulphide photocell oation Supplied with: NEMA rotaloc socket, wall mounting bracket, gaskets and fixings Connection NEMA socket Output Rating 2000W Tungsten 500W HPS(SON) Detector CdS Photocell Power Switching thresholds (lux) on 70 Oating Temature ( C) Switching thresholds (lux) off 135 Royce Thompson Electric Connection NEMA socket Switching thresholds (lux) off 35 Height 63 mm Output Rating HPS (SON) 500W, Tungsten 2000W Dia. 81 Power 0.25 W Detector Photodiode Oating Temature ( C) Switching thresholds (lux) on unit Royce Thompson Electric Portable Fluorescent Robust, self-contained inspection lamps Reflective backing strip which allows light to disse over an arc of 300 Resistant to oil and petrol, complies with BS4533 Both ends sealed with synthetic rubber caps Fitted with electronic starter/ballast Supplied with 2-core rubber sheathed cable Hook mounting Height Dia. Voltage (Vac) (max) Cable Length (m) Cable Termination IP Rating None IP None IP BS1363 IP BS1363 IP Voltage (Vac) unit unit unit unit Description CFL 11W 4-pin PL-S lamp unit FL 8 W 300 mm T5 linear unit Grip unit Electronic Control Kit (Silicon Photodiode) Solid-state electronic lighting controller utilising an optically-filtered silicon photodiode sensor for high accuracy and repeatability Fitted with a conical, UV stable, impact resistant, translucent cover Silicon photodiode light sensor Low power consumption, day or night Omni-directional Supplied with: NEMA rotaloc socket, wall mounting bracket, gaskets and fixings Royce Thompson Electric Connection NEMA socket Switching thresholds (lux) off 35 Height 119 mm Output Rating HPS (SON) 1200W, Tungsten 2000W Dia. 80 Power 0.25 W Detector Photodiode Oating Temature ( C) Switching thresholds (lux) on 70 General purpose double insulated robust gripping handlamps Ceramic BC lampholder Supplied without lamp Standard Grip Supplied without cable, use approved 0.75mm 2 (max) rubber sheathed cable Steel guard with rotating anti glare shield Safety Grip Polycarbonate handle and cover with rotating anti glare shield Colour coded with choice of plug for easy identification Supplied with rubber sheathed cable Height 280 Width OM = Order Multiple * manufacturers information unavailable at time of printing

19 ORDERLINE Description Dia. Voltage (Vac) (max) Cable Length (m) Cable Termination IP Rating Grip - Standard * Grip - Safety BS1363 IP Grip - Safety BS4343 IP Grip - Safety BS4343 IP Description Cable Termination 240V Work light Grip - Standard unit Grip - Safety BS unit Grip - Safety BS unit Grip - Safety BS unit Heavy-duty 240V work light for general workshop and onsite use. Strong impact-resistant case with hook and spring clip On/off switch in handle Uses 60W ES lamp (not supplied) Fitted with 3m mains cord terminated with an Aus/NZ mains plug Manu. Part No. WL unit V Fluorescent Work Light Description 240V BC 60W unit V BC 100W unit V BC 60W unit Twin Head Telescopic Floodlight Portable Halogen Floodlight For indoor/outdoor and industrial applications Tubular steel frame Aluminium case with a dimpled anodised aluminium reflector Toughened glass hinged cover, with silicone rubber gasket 2 cable securing lugs and rubber caps Fully adjustable lamp position Supplied with 20mm gland Note: Supplied with a 500W lamp - fitted with a BS V plug A portable enclosed floodlight for temporary site use, accepting 300W or 500W linear tungsten-halogen lamps. 2-stage extending pole and fold up legs Legs lock out in two positions to increase height or assist stability Wire storage on pole Note: Halogen lamps not supplied. Please refer to the following stock numbers: (300W equiv 230V); (500W equiv 230V) or (300W equiv 110V); (500W equiv 110V) This product is supplied configured for 230Vac oation. Height 750 mm IP Rating 44 Width 750 mm Lamp Tungsten Halogen Depth 253 mm Cable Termination BS1363 Voltage (Vac) 110/ unit K1 LV unit Height 230 mm IP Rating 44 Width 230 mm Lamp Halogen Depth 365 mm Cable Termination BS1363 Voltage (Vac) 110/ W unit V 11-watt fluorescent work light suitable for workshop and site use. Weatherproof high impact resistant casing with hanging hook Includes 11-watt fluorescent tube 5m mains lead fitted with an Aus/NZ mains plug WL11 240V fluorescent Site work light unit OM S$ S$ NOVA Tilting Head Rechargeable Floodlight Powered by rechargeable lead acid batteries (protected from deep discharge) Provides a floodlit (300 W halogen equivalent) working environment when mains power is not available Remains cool in oation and does not produce any fumes Suitable for confined spaces Adjustable head is removeable and complete with a 2 metre curly cord; no trailing leads The adjustable head can be mounted on the optional extension pole, available separately, see RS Made from high grade powder coated aluminium with a polycarbonate lens cover which can be tilted to direct the light as required Up to 8 hours full power oation LED indication of battery state inc. 90% charge capacity Charges direct from mains 230V Carrying handle for ease of transport Supplied with two lamps giving 2000 lumens in total Can be left for 6 months without recharging Expected battery life of 500 charge/discharge cycles Note: Height of removable head version when mounted on extension pole (RS ) is 1.55m. Height 550 mm 2x11 W Depth 245 mm IP Rating 66 Width 265 mm Lamp PL-S Voltage (Vac) unit Site Festoon Consisits of 2 5mm 2 arctic grade yellow flat twin double insulated cable to BS6500 and 33 ES (E27) black polycarbonate lampholders spaced at 3m intervals Lampholders are IP54 protected Solid brass and phosphor bronze contacts which are ultrasonically welded to the cable Suitable for lamps up to 60W Yellow nylon guards are available separately. See Stock No Voltage (Vac) 110 Cable length/ 100 m type IP Rating 54 Cable Termination 16A BS unit Description Nylon Guard unit V ES 60W lamp unit Description 1.5 m Extension Pole unit Many more leading brands from over 2,500 suppliers available online 1141

20 250W Tripod Work Light Professional 240V 250 watt floodlight with adjustable tripod. Weatherproof (IP23) diecast aluminium construction Temed glass lamp face with safety grill Tripod extends to 1.1 m and also folds away for easy storage 250 Watts linear tungsten halogen tube included Light output approx lumens, average life 3000 hours 2m mains cord fitted with an Aus/NZ mains plug ON-LINE Description Magnetic Base unit Octagonal Table Base unit C-clamp unit Wall Bracket unit /12V Transformer unit /12V Transformer unit W 12V unit W 24V unit Description tripod work light unit Flexible Arm Long, Fluorescent Task Light A high quality light with a 500mm flexible arm Integral 230V ballast to power the 9W compact fluorescent lamp (supplied) A variety of mounting options are available separately Voltage 230 V ac Arm Goose Neck 9 W Max. Reach 500 mm Lamp Supplied Yes Cable Length (m) 2 Sunnex Twin 500W Tripod Work Light Twin 240V 500 watt floodlight with adjustable tripod. Weatherproof diecast aluminium construction with safety grills Tripod extends to 1.8m and also folds away for easy storage 500W linear tungsten halogen tubes included Fitted with an Aust/NZ mains plug unit Floodlights Weatherproof diecast aluminium housing with temed glass front face Integral junction box with terminal strip Wall mounting bracket included 150W and 500W tungsten halogen floodlights suitable for wall or under roof mounting. Supplied complete with tube. Manu. Part No. HL unit HL unit Portable Floodlight A powerful 500W 230V portable floodlight fitted with 1 8m of cable and with an environmental rating of IP44. The tubular frame and lens grille protect the light against damage. Suitable for indoor and outdoor use. Note: fitted with Aus/Nz 3 pin plug unit Industrial Machine Lights Short Arm, Machine/Inspection Task Light Powerful, low voltage tungsten halogen lights with high output 12V or 24V 50W capsule lamp IP65 protected adjustable head, with high quality glass lens Supplied with 2m of cable and square fixing box with fixings All models have heads designed to provide efficient cooling for safe use and longer lamp life Mounting accessories and 230V/12V transformer is available separately 50 W Cable Length (m) 2 Lamp Supplied No Integral transformer No Arm Fixed; Swivel; Short Voltage (V ac) unit unit unit Description Octagonal Table Base unit Magnetic Base unit C-clamp unit Wall Bracket unit Flexible Arm long, Machine/Inspection Light Low voltage tungsten halogen spotlights with standard square fitting base 12V lamps with or without integral step down transformer 24V lamps without step down transformer Lamps have on/off switches in the base A number of accessories are available to supplement installation applications Note: The lamp head is IP54 rated. However, the base (where the switch is) does NOT have an IP rating. 20 W Max. Reach 700 mm Lamp Supplied Yes Cable Length (m) 2 Arm Goose Neck; Flexible Voltage (V ac) Flexible Arm Long, Machine/ Inspection Task Light 50 W Max. Reach 700 mm Lamp Supplied No Cable Length (m) 2 Arm Goose Neck; Flexible Integral transformer No Sunnex Voltage (V ac) unit unit Integral transformer 12 No unit /12 Yes unit No unit /12 Yes unit Description Magnetic Base unit Octagonal Table Base unit C-clamp unit Wall Bracket unit Lamp Head Cover unit W 24V unit W 12V unit Description Magnetic Base unit Octagonal Table Base unit C-clamp unit Wall Bracket unit /12V Transformer unit /12V Transformer unit W 12V unit W 24V unit OM = Order Multiple Indicates more pricing available online a New product to range

21 ORDERLINE LED Machine Light These IP67 LED task lights are designed to be used inside large machine tools to provide close-up process illumination. They are also suitable for use in many other harsh environments with their high IP rating and excellent vibration resistance. Available with a gooseneck and built-in LED driver, or with ball joint which needs a remote driver Microdriver 9 allowing greater flexibility in voltage range Hard coated aluminium housing for improved wear and corrosion protection Scratch resistant borosilicate glass lens Protected against polarity reversal and ESD 3W white LED gives long life with a well defined bright beam Height 772mm (gooseneck), 80mm (ball joint) Adjustment 360 (gooseneck), 40 (ball joint) Description Right angle mounting bracket for 60 x 60mm base Short Arm, Machine Light High power halogen machine lights for industrial use, ideal for use in fixed positions Die cast head protected to IP65 Reinforced glass cover Fitted with anti glare louvre On/off switch on head along with adjusting handle 240V versions include transformer to use 12V 55W H3 lamp 24V versions use 70W H3 lamp Lamp Supplied No Cable Length (m) 1.8 Voltage (V ac) Arm Integral transformer Fixed; Short Yes Rigid; Short No Voltage (V ac) unit unit Adjustable Arm Long, Machine Light High power halogen machine lights for industrial use, ideal for use in fixed positions Die cast head protected to IP65 Reinforced glass cover Fitted with anti glare louvre On/off switch on head along with adjusting handle 240V versions the include transformer use a 12V 55W H3 lamp (Stock Number ) 24V versions use a 70W H3 lamp (Stock Number ) Fitted with a 1.8 metre lead and plug Lamp Supplied No Max. Reach 830 mm Arm Adjustable; Long Cable Length (m) 1.8 Voltage (V ac) Integral transformer Yes unit No unit a unit Description Microdriver 9 drive 9x1W LEDs at 350mA or 4x3W LEDs at 700mA from 230Vac a unit Description 12V 55W H unit Description 12V 55W H unit Rugged lights for machine or inspection use Short arm head rotates 360 and 90 Uses 12V 35W capsule lamp which fit into aluminium reflector IP20 Adjustable Arm Long, Loading Bay Luminaire A long reach, 3 metallic arm luminaire with plastic head Will oate with either 12V or 24V halogen lamps Supplied with 12V 55W H3 type halogen lamp and universal mounting base Voltage 12/24 V ac Arm Friction; Adjustable; Long 55 W Max. Reach 1200 mm Lamp Supplied Yes Integral transformer No Voltage 12 V ac Max. Reach 500 mm 35 W Cable Length (m) 2 Lamp Supplied No Integral transformer No Arm Goose Neck; Flexible unit Description Octagonal Table Base unit /12V Transformer unit /12V Transformer unit Magnetic Base unit C-clamp unit Wall Bracket unit W 12V unit unit Description Octagonal Table Base unit Magnetic Base unit C-clamp unit Wall Bracket unit V 55W H unit Adjustable Arm Long,Bench Task Light, ES Universal mounting task luminaire with a shock resistant thermoplastic lamp head and 3 steel articulated arms with vibration proof, friction knuckle Meets BS4533 Class 1 luminaire Joint friction adjustment if required Rotatable anti-glare visor Vertical or horizontal mounting base with 20mm diameter conduit entry holes Maximum lamp size ES 60W Universal mounting task luminaire with a shock resistant thermoplastic lamp head and 3 steel articulated arms with vibration proof, friction knuckle Meets BS4533 Class 1 luminaire Joint friction adjustment if required Rotatable anti-glare visor Vertical or horizontal mounting base with 20mm diameter conduit entry holes Maximum lamp size ES 60W Voltage 230 V ac Arm Friction; Adjustable; Long 60 W Max. Reach 830 mm Lamp Supplied No Integral transformer No unit Flexible Arm Long, Machine/ Inspection Light Visit our website for additional price information and exciting promotions 1143

22 Adjustable Arm Long, Machine/Bench Task Light, ES A mains-powered task lighting luminaire using a 60W ES lamp (not supplied) designed for rugged environments Three-section 750mm reach arm Handle for safe adjustment of shade Flexible anti-glare visor Vertical or horizontal mounting screw down base with electrical connection terminal block Sealed to IP64 and meeting BS4533 Pt 101 and EN60598 Voltage 230 V ac Arm Friction; Adjustable; Long 60 W Integral transformer No Lamp Supplied No Office Bench Mount Tungsten Halogen Low voltage desk lights with integral transformer in the base On/Off switch in base Lamp protected by glass cover for extra safety ON-LINE Voltage 230 V ac Lamp Supplied Yes Description Arm Max. Reach Desk Light, 35W 35 Telescopic Desk Light, 20W 20 Telescopic unit Short Arm, Machine/Bench Task Light, ES Voltage 230 V ac Arm Fixed; Short 60 W Integral transformer No Lamp Supplied No unit Adjustable Arm Long,Task Light This 2 arm luminarie incorporates a step down transformer Supplied with dichroic 50W 12V halogen lamp Lamp head sealed to IP64 Joint friction adjustment if required Vertical or horizontal mounting screw down base with electrical connection terminal block Voltage 12 V ac Arm Friction; Adjustable; Long 50 W Max. Reach 750 mm Lamp Supplied Yes Integral transformer Yes unit Machine Lights Desk Lamp SN 136, 230 V / 36 W Universal lamp for many application areas Lamp body made of shock-resistant plastic Lamp body 5 x 118 x 70 mm Arms 430 x 400 mm Mirrored parabolic grid Protection rating IP20, protection class I Mains connection lead approximately 1.5 m with Schuko plug Connection voltage 230 V / 50 Hz Spring-balanced arms Ball joint on lamp head With 1 compact CFL lamp TC-L 36 W neutral white Colour light grey RAL 7035 Lamp supplied without base Suitable desk clamp TK 1 65 available under RS stock no Description Desk lamp SN 136 a unit Description Desk Light, 35W unit Desk Light, 20W unit Description 35W 12V unit W 12V unit PL Desk Light Non-reflecting ABS head with polished aluminium inner reflector Head orientation can be adjusted in 3 planes Balanced arms allow for movement of the board without affecting the balance of the lamp G-clamp bracket incorporates a rotatable socket connection for mounting at any angle Ideal for parallel-motion drawing boards Supplied with PL natural colour fluorescent tube, integral starter, high frequency ballast to eliminate flicker and 2m of double insulated (BS4533) cable Voltage 240 V ac Arm 2-section spring balanced 13 W Max. Reach 830 mm Lamp Supplied Yes Luxo FL101Plus CFL Desk Light FL 101 Plus is a symmetric lamp especially suitable for work benches and other large work surfaces, it is the upgraded,version of Luxo s popular FL 101 and now benefits from a high frequency ballast for flicker free lighting and single 24,watt 2G11 lamp. The shade can be adjusted vertically, horizontally and laterally to almost any desired position. Arm length: 1050mm Shade width: 35cm Light output: 2200 lux at 40cm from the work surface Supplied with table bracket Max. Reach unit W 1050 mm unit Dimming Halogen Desk / Table Light Voltage 240 V ac Arm Gooseneck 20 W Max. Reach 700 mm Lamp Supplied Yes Sunnex unit OM = Order Multiple a New product to range