Intelligent Lift Control Valve with Electronic Card

Size: px

Start display at page:

Download "Intelligent Lift Control Valve with Electronic Card"

Noah Gilbert
6 years ago
Views:

Intelligent Lift Control Valve with Electronic Card Q max = 500 l/min, p max = 80 bar Leak-free, two-stage, electronically controlled, without frequency control i50 and i500 Information lift-control

1 Intelligent Lift Control Valve with Electronic Card Q max = 500 l/min, p max = 80 bar Leak-free, two-stage, electronically controlled, without frequency control i50 and i500 Information lift-control valve No modifications of the travel curve or mechanical adjustments are necessary Constantly short travel times, regardless of loading and temperature Constant levelling accuracy of ± mm, which prevents dangerous tripping accidents Self-monitoring function guarantees fully integrated A conformity (TÜV approved) Pleasant acceleration and slowdown thanks to an electronically controlled travel curve Soft-stop function for smooth approach and entry. The ivalve lift-control valve is an electronically controlled hydraulic valve block for controlling hydraulic lifts. The ivalve is situated on the hydraulic power unit and activated by the lift control system. Electronic control is accomplished by an electronic unit the icon that is housed in the control cabinet. At standstill, the weight of the lift is supported by a check valve integrated in the ivalve. In operation, the electronic controller regulates the states Travel UP and Travel DOWN, and the transitions between these states. In the electronic unit, the travel is represented in a form known as travel curves. During operation, the travel curves for that particular lift are optimised by the learning algorithm iteach. In addition, the valve block includes the following functions and components: a hand pump with manual emergency lowering (with piston-creep prevention), a ball valve, a pressure gauge, a pressure sensor with up to two pressure switches, speed monitoring, a temperature sensor, an emergency stop DOWN valve (UCM/A) in accordance with EN 8.. Technical data ivalve General characteristics, value, unit i50 i500 Designation Design Intelligent lift-control valve Leak-free, two-stage, electronically controlled Mounting method G Pipe mounting or low mounting (see interface in Installation info. ) G ½ Pipe mounting or low mounting (see interface in Installation info. ) Size - Port P - Port T - Port HP - Port Z - Port Z G G Hose, oil-resistant (id = 8 mm, od = mm) 8 L EN ISO 8- G ¼ G ½ G ½ Hose, oil-resistant (id = 8 mm, od = 0 mm) L EN ISO 8- G ¼ Tightening torque - Port P - Port T - Port HP - Port Z - Port Z 0 Nm ± 0 % 0 Nm ± 0 % Hose 0 x (pushed on) 0 Nm ± 0 % 5 Nm ± 0 % 500 Nm ± 0 % 500 Nm ± 0 % Hose 0 x (pushed on) 500 Nm ± 0 % 5 Nm ± 0 % Reference: 00-P EN-0 Issue: 0.07 /

2 General characteristics, value, unit i50 i500 Weight 0. kg.5 kg Mounting attitude Ambient temperature range As illustrated see section Dimensions + C +0 C Hydraulic characteristics, value, unit i50 i500 Nominal pressure 80 bar 80 bar Maximum flow rate 50 l/min 500 l/min Nominal flow rate Down (Z > T) Flow direction see section Performance graphs P T (bypass) P Z (UP) Z T (DOWN) Hydraulic fluid HL and HLP mineral oil to DIN 5 5; for other fluids, please contact BUCHER Hydraulic fluid temperature range Viscosity range Minimum fluid cleanliness Cleanliness class to ISO 06 : C +60 C mm /s (cst) Class /9/6 Electrical characteristics Supply voltage Supply voltage tolerance, value, unit i50 VDC ± 0 % i500 / 00-P EN-0/0.07

3 . Schematic ivalve Z Z 9 C 6 P U 8 Q U A D T U P HP P T Item Item Main spool Pressure relief valve Ball valve Pilot operated check valve 5 Emergency stop DOWN valve (UCM / A) 6 Piston-creep prevention 7 Hand pump 8 Pressure relief valve in the hand pump 9 Pressure gauge C P T HP Z Z icon (included in the delivery) ibox Pump Tank Hand pump Cylinder Test port 00-P EN-0/0.07 /

4 . Performance graphs Legend 500 mm /s (cst) Motorex Corex HLP 6 at approx. C 75 mm /s (cst) Motorex Corex HLP 6 at approx. 0 C.. ivalve 50 Δp = f (Q) Pressure drop - Flow rate characteristic [i50/60] (min. dynamic pressure/flow rate) Δp [bar].5 ivalve-50_p0.ai Δp = f (Q) Pressure drop - Flow rate characteristic [i50/50] (min. dynamic pressure/flow rate) Δp [bar].5 ivalve-50_p0.ai 0 Down (Z-T) 0.0 Down (Z-T) Up (P-Z) Up (P-Z) Q [l/min] Q [l/min].. ivalve 500 Δp = f (Q) Pressure drop - Flow rate characteristic (min. dynamic pressure/flow rate) Δp [bar] 9 ivalve-500_p0.ai Down (Z-T) Up (P-Z) 500Q [l/min] / 00-P EN-0/0.07

5 .5 Dimensions, interface ivalve i A-A 5 Z (G/ ) P (G ) T (G ). 5 HP B-B Low-mounting connection see Figure A-A Pipe-mounting connection see Figure B-B 00-P EN-0/0.07 5/

6 .6 Dimensions, interface ivalve i500 9 (90) HP Z (M5x) 7 (66) A-A (G½) P T (G½) 8.75 B-B P B Low-mounting connection see Figure A-A Pipe-mounting connection see Figure B-B A-A B-B HP P HP T 00-P B.5 6/ 00-P EN-0/0.07

.7 Application examples The lift-control valve is an electronically controlled hydraulic valve block for controlling hydraulic-powered passenger and goods lifts.

7 .7 Application examples The lift-control valve is an electronically controlled hydraulic valve block for controlling hydraulic-powered passenger and goods lifts. The lift-control valve is situated on a hydraulic power unit and activated by a lift control system..8 Model code ivalve IVALVE - 50 / 60 Rx.x IVALVE = Intelligent lift-control valve 500 = Nominal size = Nominal size = Flow rate 500 l/min (nominal size 500) 50 = Flow rate 50 l/min (nominal size 50) 60 = Flow rate 60 l/min (nominal size 50) R.0 = Release / Design stage Electronic card for lift-control valve icon Potential-free switching output for faults Two configurable switching outputs (pressure switch, train speed supervision) Functions can be expanded via options board. icon The ivalve lift-control valve is an electronically controlled hydraulic valve block for controlling hydraulic lifts. The electronic control is accomplished by an electronic unit the icon that is housed in the control cabinet. In operation, the electronic controller regulates the states Travel UP and Travel DOWN, and the transitions between these states. In the electronic unit, this travel is represented in a form known as travel curves. During operation, the travel curves for that particular lift are optimised by the learning algorithm "iteach". The ParamCard is a memory card on which the system-specific parameters and data are stored. The ParamCard plugs into the icon. Without the ParamCard being plugged in, no lift travel can be carried out. 00-P EN-0/0.07 7/

8 . Technical data General characteristics Designation Design Electrical connection Mounting method icon Mounting method Weight Ambient temperature range Relative air humidity Dimensions (overall sizes W x H x D) Supply voltage Supply voltage tolerance Max. ripple - solenoids - electronics, value, unit icon Printed circuit board with layers -pin square plug to ISO 00 / DIN 650 PCB connector.5 / 5 mm (screw terminals) Plug connector kit available - see the chapter Accessories 5/5 mm cap rail acc. to EN 5005 (G) or EN 500 (TS5, TS5) Option boards spacer studs Mx6 (included in delivery) 0.0 kg + C +0 C 0 90% (without condensation) x x 6 mm (without options board) VDC ± 0 % 50 mv pp max. (ripple and noise) Power consumption at max. control current Command inputs Switching outputs Relative duty cycle Max. Nominal power consumption at standstill Relay contact rating: Min. control current Max. voltage Max. power 50 W (i50) 0 W (i500) active / + V active (configurable) Potential-free relay contacts 00 % W 0 ma / max. A 50 VAC 750 VA (AC) / 90 W (DC) Electromagnetic compatibility: interference immunity EN 06 Electromagnetic compatibility: interference emission EN 05 Protection class to ISO 0 65 / EN IP 00 8/ 00-P EN-0/0.07

9 . Block diagram Lift control system (customer s) + V DC *** X X7 +V DC PE icon ParamCard K 6 K K K K5 K6 K7 K8 +V * ** Monitoring SMA 5 X6 X X8 +SMA (V DC) (0.A) k5 +V DC 0,7A 7W +V +V i50 i500 +V DC+V DC. A.0 A 0W 8W X5 m0 m0+ m m+ NR NR FR ye gn br wt FR ivalve X nc error no nc s no nc s no Switching output Relay fault / SIU Switching output Relay s Switching output Relay s Solenoid Solenoid UCM / A UP /DOWN travel (black plug) (grey plug) ibox X com/meas Handterminal / PC X RS 00 P * Configurable via software, -active/ +V-active (applies to all inputs K... K8) ** Configurable via software, -active/ +V-active (applies to all inputs K... K8) *** IMPORTANT!: If there is no connection between Earth and on the elevator control-system side, it is essential that X. be connected to earth! 00-P EN-0/0.07 9/

10 . Dimensions.. Electronic card icon basic board 6 00 min ~7 G EN 5005 ~ TS5 EN P Electronic card icon with options board ( additional switching outputs) G EN 5005 TS5 EN P / 00-P EN-0/0.07

11 .5 Pin assignments icon electronic card basic board X8 X0 X7 X6 X5 X X0 X7 X6 X5 X pwr run up down misc. X8 +SMA m0(9) m(0) com/meas X X9 card X RS X9 ok C0 select X +V DC PE error s s X errror s s 00 P X X Item Item ParamCard Top-hat rail TS5, TS5 (EN 500) or G-type rail G (EN 5005) X X X X Connector block power supply Connector block switching outputs Connection Handterminal / PC Connection ibox X5 X6 X7 X8 X9 X0 Connector block solenoids Connector block command signals K6 K8 Connector block command signals K K5 Socket for ParamCard Socket for options boards Connector block, SMA IMPORTANT!: Two independent switching outputs are available on the icon. For each switching output, a relay (s and s) is available, each with a break/make contact. IMPORTANT!: K coding and binary coding are possible. For other information, please contact BUCHER! 00-P EN-0/0.07 /

12 .5. Options board, switching output Options board for version with pressure switch X50 X50 X0 X0 X S S 00-P Item Item X-0 Connector block, switching outputs X-50 Socket for options board X- Not used / 00-P EN-0/0.07

.6 Dummy icon optional.6. The "Dummy icon" can be pre-installed in the control cabinet as a "placeholder" instead of the real icon (control electronics for the ivalve).

13 .6 Dummy icon optional.6. The "Dummy icon" can be pre-installed in the control cabinet as a "placeholder" instead of the real icon (control electronics for the ivalve). It has all the plug connectors that the icon has, so that the wiring can also be done in advance (cable lengths and cable positions)..6. How customers contact the test system The central "X" plug offers an additional benefit. All signals that are wired from outside to the icon are available on this plug. Consequently, the wiring can be checked with an automatic test system..7 Accessories Part No Dummy icon Handterminal including connecting cable PC software "iwin", including connecting cable Power supply module i Power supply module i Plug connector kit Solenoid connection cable:.5 metre 6.0 metre metre (for Halogen-free versions, contact Bucher) ibox connection cable:.5 metre 6.0 metre metre Related documents Reference 00-D I I S S Planning information ivalve Commissioning and maintenance ivalve Parametrization and maintenance ivalve Spare parts ivalve / icon i50 Spare parts ivalve / icon i500 info.ch@bucherhydraulics.com 07 by Bucher Hydraulics AG, CH-65 Neuheim All rights reserved. Data is provided for the purpose of product description only, and must not be construed as warranted characteristics in the legal sense. The information does not relieve users from the duty of conducting their own evaluations and tests. Because the products are subject to continual improvement, we reserve the right to amend the product specifications contained in this catalogue. Classification: P EN-0/0.07 /

Proportional Flow-Control Cartridges, Size 5

Proportional Flow-Control Cartridges, Size Q max = l/min, p max = bar, Q N = l/min at p bar Leak free, load compensated, two stage Description Series MVRPLSA two-stage proportional flow-control cartridges