CNC 2 Wheel Brakes. CNC Dual Master Cylinder Pedal Assembly. CNC Floor Mount Master Cylinder. CNC Hydraulic Clutch Kit

Transcription

1 CNC 2 Wheel Brakes The complete set-up for long trouble free operation. Smooth easy pedal action and quick stops. This kit is easy to install and is the ultimate in custom hydraulic equipment. The hydraulic slave cylinder actuates your clutch for crisp action in all driving conditions CNC 2 Wheel Brakes w/cable Throttle Pedal (VW & Corvair) CNC Dual Master Cylinder Pedal Assembly Your car will have completely independent front and rear braking systems for safety and control. Features a fully adjustable equalizing bar which permits exact pressure adjustments on front and rear wheel cylinders. A special pivot bearing and threaded Heim Joints assure safe and easy push rod travel CNC Dual Master Cylinder Pedal Assembly CNC Hydraulic Clutch Kit Fits Type 1 through 4 transmissions with 4 and 5 speeds, is easy to install, and provides smooth positive starts and shifts in all terrains. The pedal assembly bolts to the floor of most frames, and features an aluminum master cylinder and reservoir. Can also be mounted inverted, under the dash of off-road and race cars CNC Hydraulic Clutch Kit - Pedal Assembly, Slave Cylinder CNC Floor Mount Master Cylinder Can be used to power your brake system or hydraulic clutch. 10 1/4" pedal length provides 5.2 to 1 ratio to provide more than adequate braking power CNC Floor Mount Master Cylinder - 5/8'' Bore 6619 CNC Floor Mount Master Cylinder - 3/4'' Bore CNC Optional Easy Fill Cover Quickly and easily add more brake fluid! For use with CNC Dual Master Cylinder Pedal Assemblies. CNC Replacement Master Cylinders Complete & Ready to Install. Made by CNC CNC Optional Easy Fill Covers (each) 6168 CNC Replacement Master Cylinder - 3/4'' Bore 6169 CNC Replacement Master Cylinder - 5/8" Bore 01

2 CNC Repair Kits 6135 CNC Master Cylinder Kit - 3/4 bore - Brake/Clutch Cylinder w/round Reservoir 6136 CNC Brake Master Cylinder Repair Kit - 3/4 bore - Cylinder w/square Reservoir 6137 CNC Brake Master Cylinder Repair Kit - 7/8 bore - Cylinder w/square Reservoir 6138 CNC Turning Brake Repair Kit - 5/8 bore - Dual Handle Assembly 6139 CNC Turning Brake Repair Kit - 3/4 bore - Dual Handle Assembly 6140 CNC Turning Brake Repair Kit - 5/8 bore - Single Handle Assembly 6141 CNC Turning Brake Repair Kit - 3/4 bore - Single Handle Assembly 6142 CNC Sand Buggy Rear Disc Brake Replacement O-Ring Kit 6143 CNC Sand Buggy Rear Disc Brake Replacement Piston 6144 CNC Clutch Slave Cylinder Rebuild Kit - Pull type cylinder - 7/8 bore 6191 CNC Master Cylinder Kit - 5/8 bore - Brake/Clutch Cylinder w/round Reservoir 6492 CNC Clutch Slave Cylinder Rebuild Kit - Push type cylinder - 7/8 bore CNC Throttle Cable Accessories Attaches to CNC Hydraulic Throttle Pedal to provide a connection for throttle cable Made by CNC. Self locking clevis, used on adjustable mounting plates CNC Throttle Cable Bracket 6644 CNC Throttle Cable Extension 6645 CNC Throttle Cable Extension (cut to size) 6646 Hook Clamp - for quick cable removal Cable Clamp & Shim 6648 Aluminum Half Clamp CNC Sheathed Cable Made by CNC. CNC Throttle Cables are similar to, and interchangeable with Morse control cables. CNC cables can be used to push or pull the throttle. Cable ends are ridged and fitted with threaded ends to provide for attaching various connectors. CNC Slave Cylinders Clutch Slave Cylinder can be used with most any master cylinder CNC Sheathed Throttle Cable - 7 length 6640 CNC Sheathed Throttle Cable - 8 length 6641 CNC Sheathed Throttle Cable - 9 length 6642 CNC Sheathed Throttle Cable - 10 length 6076 CNC Clutch Slave Cylinder - VW Pull Style (cylinder only) 6493 Slave Cylinders - Universal Push Style 6494 Slave Cylinders Push Rod 6495 Slave Cylinders - Universal Pull Style 02

3 CNC Turning Brake Single Handle 5/8" bore sizes are most often used with drum brakes, disc brakes require the use of 3/4" bore cylinders. CNC Dual Handle Turning Brakes have chrome plated handles and anodized aluminum knobs CNC Turning Brake - Single Straight Handle (3/4 Bore) 6348 CNC Turning Brake - Single Angled Handle (3/4 Bore) CNC Turning Brake Dual Handle Single Straight Handle Turning Brakes allow installation where two handle brake assemblies will not fit. They are equipped with a single chrome handle and an anodized aluminum knob. A 7/8" bore is suggested for use with drum brakes, the larger 3/4" bore size should be used with disc brakes CNC Turning Brake - Dual Straight Handle (5/8 Bore) 6347 CNC Turning Brake - Dual Straight Handle (3/4 Bore) CNC Turning Brake Dual Angled Handle CNC Staging Brake Made by CNC. Can often be utilized when straight or vertical handles interfere with the shifter, dash or other hardware. Equipped with a single chrome handle and an anodized aluminum knob. A 5/8" bore is suggested for use with drum brakes, and the larger 3/4" bore size should be used with disc brakes CNC Turning Brake - Dual Angled Handle (5/8 Bore) 6349 CNC Turning Brake - Dual Angled Handle (3/4 Bore) 6486 CNC Staging Brake - Angled Handle (3/4" bore) 6488 CNC Staging Brake - Straight Handle (3/4" bore) CNC Hand Brake Made by CNC. Replacement Parts Made by CNC. Replacement knobs and clevis with pin for turning brakes, hand brakes and master cylinders CNC Hand Brake - 5/8" bore 6490 CNC Hand Brake - 3/4" bore 6622 Clevis & Pin (Red) 6623 Clevis & Pin (Blue) 6625 Turning Brake & Hand Brake Knob (Red) 6626 Turning Brake & Hand Brake Knob (Blue) 6627 Clevis & Pin (Red) 6628 Clevis & Pin (Blue) 03

4 Residual Pressure Valves The JAMAR Pro-X Series Shifter features a sealed hardened stainless steel selector shaft and shift lever. The housing is manufactured from 6061 Billet Aluminum and comes with a Polished Finish. The All New Design allows shifting into reverse by pushing down and pulling back; no more two handed shifting as with the old super shifter Residual Pressure Valve - 2 lb. (1/8" NPT) 6609 Residual Pressure Valve - 4 lb. (metric) 67-later 6624 Residual Pressure Valve - 10 lb. (1/8" NPT) Metric Bubble Flare These sometime hard-to-find fittings are now available in one convenient location. Great for plumbing a new buggy or just to replace a broken or lost part. Master Cylinder Plug For use to plug outlets in VW Master Cylinders /16'' American Line to Metric Thread Bubble Flare - Coupler 6635 Metric Bubble Flare - Female to 1/8'' Pipe - Male - Straight 6636 Metric Bubble Flare - Female to 1/8'' Pipe - Male - Elbow 6637 Metric Bubble Flare - Male to 3/16'' American Line Female - straight 6638 Metric Coupler 4339 Master Cylinder Plug 04

5 JAMAR Clutch Pedal A great looking JAMAR competition clutch pedal with a billet slave cylinder. JAMAR Brake Pedal Assembly A dual master cylinder with a balance beam to provide independent adjustment of front and rear braking force JAMAR Clutch Pedal with 11/16'' Slave 6203 JAMAR Brake Pedal Assembly - w/slim Line Master Cylinder & Easy Fill Tops JAMAR Billet Repair Kits Kits include everything you need to rebuild your JAMAR Turning Brakes, Pedal Assemblies and Clutch Slave Cylinders JAMAR Billet Sand Buggy Pedal Assembly Repair Kit - 11/16 bore Clutch Cylinder 6116 JAMAR Billet Sand Buggy Pedal Assembly Repair Kit - 19mm bore Brake Cylinder 6117 JAMAR Billet Clutch Slave Cylinder Repair Kit 6118 JAMAR Billet Turning Brake Repair Kit - 3/4" bore - Dual Handle 6119 JAMAR Sand Buggy Disc Brake Repair Kit 6154 JAMAR Billet Turning Brake Repair Kit - 5/8" bore - Dual Handle 6491 JAMAR Compact Turning Brake Repair Kit - 5/8" bore JAMAR Park Lock Push on the brake pedal, depress the Park Lock and your brakes are locked. To release, just step on the brake pedal. Fits most any vehicle and can be used to stage on hills. (Uses 1/8"NPT) JAMAR Steering Box Cover Add glitz to the ugliest part on your dune buggy, the steering box! It's designed to bolt right onto all T-1 steering boxes. It's 100%, reliable in form and function because it adds strength and custom looks to your dune buggy JAMAR Park Lock 6151 JAMAR Billet Steering Box Cover 05

6 CNC Adjustable Pedal Mounting Plate Mounts on the floor of the vehicle and allows you to quickly adjust your pedal assembly to the drivers height. It can be used with all dual master cylinder assemblies. Three different locations provide fast adjustment for any driver CNC machined from heavy gauge aluminum plate and brush finished to compliment your vehicle Adjustable Pedal Mounting Plate - CNC CNC Throttle Pedal Made by CNC. Machined from cast aluminum to provide rugged no-nonsense throttle control. It bolts solidly to the floor of your car and is equipped with a return spring. CNC Throttle Pedal Made by CNC. The racers choice with adjustable forward and rear stops, side foot rest, and non-skid surface. 3 cable mounting positions provide cable action best suited for your engine. Fits dune buggies and race cars Throttle Pedal - CNC 6194 CNC Throttle Pedal with Foot Brace (angled) JAMAR Pro-X Billet Aluminum Throttle Pedal Looks fast just mounted in your car. Great fit and feel combined with an adjustable throttle cable mount make this a perfect pedal for the strip or sand JAMAR Pro-X Billet Aluminum Throttle Pedal Turbo Throttle Pedal Gives you precise throttle control and custom appearance. It bolts right into '66 and later Type-1 and Type-3 VW's to replace the complete factory throttle assembly. Manufactured from cast aluminum for increased strength, rigidity and smooth action. The pedal rides on an aluminum roller to assure full throttle response and quick "no jam" operation Turbo Throttle Pedal 06

7 JAMAR Adjustable Billet Front Beams The most beautiful Front Beams you can install are manufactured by JAMAR. JAMAR Billet Front Beam NEEDS DESCRIPTION. Light weight and full on billet! 6235 JAMAR Front Beam - Adjustable w/o Shock Towers 6236 JAMAR Front Beam - Adjustable with Shock Towers 6239 Replacement Bushings - JAMAR or Warrior Beam (set of 4) 6263 JAMAR Front Beam - w/o Shock Towers (No Adjusters) 6264 JAMAR Front Beam - with Shock Towers (No Adjusters) JT Aluminum Front Beam Lightweight, strong and easy to install. In/Out Bushings NEEDS DESCRIPTION. If you are into Sand Rails, you've gotta have one of these super lightweight JT Aluminum Front Beams. Accepts stock or high performance spindles and torsion leaves. Beams are designed to fit early link pin style frames Front Beam - JT Aluminum with Shock Towers 6276 Replacement Bushings for JT Beam (set of 4) 6245 In/Out Bushings - Needle Bearing Link Pin (set of 4) 6246 In/Out Bushings - Ball Joint (set of 4) 07

8 Buggy Whips Manufactured from rugged wound fiberglass and equipped with a brilliant red flag. Whips are supplied with mounting hardware and an electrical connector Buggy Whip Flag - Replacement 6170 Buggy Whip - 5 ft. Non-Lighted Econo 6173 Buggy Whip - 8 ft. Non-Lighted Econo 6180 Buggy Whip - 5 ft (with light connector) 6181 Buggy Whip - 8 ft (with light connector) 6182 Buggy Whip Quick Mount Buggy Whip Bulb Shield Fits snugly over the Buggy Whip light socket. Part # Color Amber Green Red Blue 6155 Buggy Whip Bulb (35 Watts) 6223 Buggy Whip Bulb Shield Cover Buggy Whip Lamp Shield Bulb is completely enclosed and protected from the environment. Available in four colors: Blue, Amber, Red & Green. LED Whip Light Fits standard pole socket. Perfect addition to your lighted Dune Buggy Whip. Use it at base camp to find your way home. Draws less than one half amp. Solid state with LED lights and designed to outlast your vehicle. Part # Color Blue Red Amber Green 6192 Red White & Blue LED Whip Light - Flashing 6193 Red White & Blue LED Whip Light - Non-Flashing Hinged Billet Whip Mount Clamps on to 1 1/2" tubing Hinged Billet Whip Mount - Clamp On (1 1/2'' tubing) 08

9 CROW 2 Street & Buggy Harness The 2" Street and Buggy Harness is light weight enough to be comfortable, but it's all serious business. It's sewn from sturdy nylon webbing, and the seat belt ends are double stitched into heavy gauge plated steel mounts. The shoulder harness is finished in universal "Y" style to allow roll bar or floor mounting. Street and Buggy Harnesses are equally at home in a sand buggy, baja bug, or street sedan. Choose from Grey, Blue, Red, or Black, nylon straps. 2" Street & Buggy Harness (one seat) floor mount Part # Color Grey Black Blue Red CROW 3 Sand Buggy Harness Patterned after the 3" seat belt used in NHRA competition and manufactured to prevailing Mil-Spec standards. 2" adjustable Shoulder Straps connect to the latch assembly for quick entry/exit. The ultra quick/latch type buckle is manufactured from forged steel. Shoulder straps are available in roll bar or floor mount styles. This series of seat belts has been specially designed for sand buggies and baja bugs. It's heavy duty 3" belt will keep you nailed in the seat. 3" Sand Buggy Harness (one seat) floor mount Part # Color Grey Black Blue Red 3" Sand Buggy Harness (one seat) roll bar mount Part # Color Grey Black Blue Red Measures 59" around the lap belt, from eyelet to eyelet. CROW 3 Shoulder Harness Exceeds all Mil-Spec standards and designed for use with 3" Competition Lap Belts. The forged steel hardware connects to the latch assembly for quick entry/exit. All 3" Shoulder Harnesses come with special "off-road" adjusters that are equipped with spring tensioners to prevent accidental loosening while in use CROW 3" Shoulder Harness - Black (one seat) roll bar mount 7047 CROW 3" Shoulder Harness - Black (one seat) floor mount 09

10 3 Competition Lap Belt Approved by all racing associations. Full 3 in width and equipped with special quick release. May be used with Shoulder Harnesses, and Submarine Belts. Necessary hardware issupplied with each belt CROW 3" Competition Lap Belt - Black (one seat) 5 Way Harness Combines the 3" Competition lap, 3" Shoulder Harness and the Anti- Submarine Belt in a complete race ready resistant system. This setup does it all! You have your choice of roll bar or floor mount shoulder harness, and the assurance that you have the finest in driver protection CROW 5 Way 'V' Harness, Snap-In (one seat) 7015 CROW 5 Way 'Y' Harness, Snap-In (one seat) Anti-Submarine Belt Designed to work with 3" Competition Lap Belts. Connects to floor of car to help keep driver from sliding forward during sudden deceleration and stops. Quick disconnects for fast entry and exit CROW Seat Belt - Anti-Submarine Belt - Black (one seat) Seat Belts Bolts into standard factory locations. Features wide comfortable buckles with easy release buttons. Double stitched from SAE approved nylon webbing. Shipped in complete sets to fit 2 seats Point Seat Belts - Black w/wolfsburg Logo (two seats) Point Seat Belts - Black w/wolfsburg Logo (two seats) Seat Belt Bolts OEM Forged Seat Belt bolts thread right into all VW Sedan pans and door posts to mount all VW seat belt assemblies. Floor Mount Washer Kit NEEDS DESCRIPTION. These bolts are shipped in sets of 4, and can be used to mount front or rear seat belts Seat Belt Bolts - VW (set of 4) 6593 Floor Mount Washer Kit 10

11 Poly Seats Polyethylene plastic seats feature hollow, one piece, seamless construction with a molded black non-fade grained surface. The unique double-walled design delivers a comfortable, impactabsorbing ride. They provide maximum strength and minimum weight with excellent elasticity to resist vibration and shock damage. Each Poly Seat has molded in 5/16"- 18 threaded inserts for easy mounting. Each seat has slots for a 5-way harness. Fiberglass Seats Low cost, easy installation, light weight, and durability! Fiberglass seats allow the driver to sit lower in the car, thereby providing additional head room in sand buggies and vehicles with roll cages. Many Pro Stock chassis builders prefer this type of seat for driver safety and quick removal. Low Back Bucket Seat 5495 Low Back Bucket Seat (Fiberglass) 5492 Low Back Seat Cover (Purple) 5496 Low Back Seat Cover (Black) 14" 23.5" 14" Universal High Back Seat 16.5" 5485 Universal High Back Seat (Fiberglass) **OVERSIZES** 5486 Universal High Back Seat Cover (Black) 31" 36 Bench Seat The simple solution for off-road buggy or Baja Bug backseats. Lightly padded Seat Covers fit the 36" Fiberglass Bench Seat " Bench Seat (Fiberglass) Bench Seat Cover (Black) Bench Seat Cover (Red) Bench Seat Cover (Yellow) Low Back Turbo Pro Poly Seat 7450 Low Back Turbo Pro Poly Seat 7457 Low Back Turbo Pro Seat Cover (Black) 7463 Low Back Turbo Pro Seat Cover (Purple) 14" 18.75" 26.5" 19.75" 9.5" 12.5" 20.5" 14" 20" High Back Turbo Pro Poly Seat 7451 High Back Turbo Pro Poly Seat 7452 High Back Turbo Pro Seat Cover Black 32.75" 19.75" 9.5" 12.5" 20.5" 11

12 Dune Buggy Tail Lights The 4 1/4" diameter, trim thickness and DOT lenses add up to the best value in dune buggy tail lights. These lights are precision injected from high impact Polyvinyl with a never rust bright chrome plated housing. Cast in base flanges, 9/16" mounting bolts and rubber washers hold these beam securely in position. Eagle Eye Headlight High Beam, low beam and street legal in quartz and brilliant chrome. The perfect solution for fiberglass dune buggies, custom cars, hot rods, antique cars, trucks and tractors. Shipped to you with 60/55W quartz halogen bulb. Part# Color Red Orange Purple Blue Green 6681 Eagle Eye 60/55 Quartz Halogen H-4 Headlight (each) Mini-Compact Chrome Lights Modern Mini-Compact design is easy on the eyes, features die cast construction, and a brilliant custom chrome finish. Perfect for use as parking, clearance, turn signals, or even tail lights. 1 3/4" x 1 1/8" x 1 5/8". Part# Color Blue Green Purple Red Clear 7656 Mini-Compact Single Filament Replacement Bulb Billet Buggy Light Features a chrome finish and an attractive bullet shape. Uses a 2 1/4" Diameter clear lens. Sold Individually Billet Buggy Light - 50 Watt 6665 Billet Buggy Light - 85 Watt Bulb 2 1/4 Quartz Lights Powerful, state of the art lighting in a small chrome housing. A potent 50wt quartz halogen beam is mounted in a Patended Dichronic multi-faceted reflector. The chrome housing is mounted on a sturdy adjustable base for easy mounting. They are designed are designed strictly for off-road use /4" Quartz Lights (set of 2) Blue Dots A touch of 50 s nostalgia with a set of BLUE DOTS. Drill your plastic tail light lens and slip 'em in. This is the way it was way back then. Shipped in sets of two Blue Dots 12

13 Rectangular Eagle Eye Lights - 100w Equipped with rubber mounts and defused lenses to fill in the gaps. Eagle Eye gives out the extra coverage you need in the rough country. Two sizes are available to fit your driving requirements Rectangular Eagle Eye Lights (100w) Stainless Steel Rectangular Eagle Eye Lights (100w) Black Enamel Rectangular Eagle Eye Lights (100w) Chrome Plated 9 Round Eagle Eye Lights - 100w See what you've been missing with a set of Eagle Eye Off-Road Lights. Eagle Eye Lights are manufactured for the serious off-road racer. They are 100% rubber shock mounted, feature a metal B-X wire loom lead, and a rubber sealed bulb retainer. You can choose from stainless steel, chrome plated or black enameled six inch lights with up to 200,000 candle power. Five inch Racing Lights blazing out with 120,000 candle power are also available in stainless steel, chrome and black enamel. These lights are strictly for off-road use. They are so powerful that they are not approved for highway use in any state! This is the same type of lighting used on aircraft for night landing. Distinctive vinyl protective covers are supplied with each Eagle Eye Racing Light Round Eagle Eye Lights (100w) Black Enamel Round Eagle Eye Lights (100w) Black Enamel Round Eagle Eye Lights (100w) Chrome Plated Round Eagle Eye Lights (100w) Chrome Plated Round Eagle Eye Lights (100w) Stainless Steel Round Eagle Eye Lights (100w) Stainless Steel

14 Grant Steering Wheels Chrome Three Spoke Design with Round Holes and Black Foam Cushion Vinyl grip. Available in three classic diameters. Great for Sand Rails and Fiberglass Buggies Steering Wheel - 10'' Super Deep Classic (5 1/2 dish) 4781 Steering Wheel /2'' Classic (3 3/4 dish) 4782 Steering Wheel /2'' Super Classic (2 dish) Chrome Steering Shaft The final link between car and driver, this shaft is designed to be used on any chassis or kit car. Long enough for any application, it can be cut to fit any size, Hub allows for a bolt on installation of any custom steering wheel. Made of thick 7/8" diameter tubing 4050 Chrome Steering Shaft Buggy Steering Shaft Mount Here's the first good looking steering shaft mount available for dune buggies. It's manufactured from top quality, cast aluminum, and features a self lubricating bushing. The textured surface has the appearance of an expensive sports car dash. The face plate has plenty of room for a starter button and switch Custom Buggy Steering Shaft Mount Steering Wheel Hubs CNC machined from aluminum stock to give your buggy a custom billet look. Bolts right on to 3 bolt dune buggy steering shafts to facilitate installation of all Wolfsburg steering wheels. The #6228 bolts to the Quick Release Steering Hub to provide for the installation of a Wolfsburg series steering wheel Steering Wheel Hubs - Billet Steering Wheel Adapter - Adapter and Emblem kit 6221 Steering Wheel Hubs - Bilet Emblem 6227 Steering Wheel Hubs - Billet Steering Wheel Adapter - Adapter Only 6228 Steering Wheel Hubs - Quick Release Billet Adapter 4771 Quick Release Steering Wheel Hub (includes hex stub shaft)

15 Aluminum Gauge Consoles Provides fast installation and lasting protection for your switches and gauges. Each instrument box is manufactured from sturdy.060 aluminum with a custom brushed surface. A 2" glare shield provides added protection for switches and gauges. The larger enclosures measures 9 1/2" W x 3" T x 3 x W The instrument openings measure 2 1/8" and accept VDO COCKPIT gauges. Two 3/4" holes are provided for your cars ignition switch and warning light. Four toggle switch holes allow you quickly to wire it up and get it on the dunes Aluminum Gauge Console - Large w/holes 7471 Aluminum Gauge Console - No holes 7472 Aluminum Gauge Console - Small Roller Pedal The early style VW pedal works great in all types of dune buggies and race cars. The large roller helps smooth out throttle movement in the rough stuff. It can be used to replace standard throttle pedals in stock sedans or in pedal mount assemblies installed in off-road race cars or dune buggies Roller Pedal - Black VW Sedan Pedal Assembly Replace your worn and cracked clutch, brake and gas pedal parts with a brand "NEW" O.E.M. assembly. Now featuring a grease Zerk Pedal Assembly - VW Sedan 6095 Pedal Ass. Repair Kit - fits Sedans & Squarebacks (to 65) 6102 Pedal Ass. Repair Kit - Sedans & Squarebacks ( 66-on) Universal Throttle Cable One cable does the job. It's manufactured from multi-strand super flex steel to provide smoother, precise throttle action. It fits every air cooled VW ever made, and a lot of water cooled ones too! It will out last the more rigid VW cable many times. You can update an early stiff wire cable with the new Super Flex Cable or replace a worn or broken Sedan, Buggy, Bus or Squareback cable. Measures 15 1/2 feet Universal Throttle Cable Tach Bag Keeps sand and moisture out of your Five Inch Tachometer. Just slip it over your Tach and tighten the drawstrings. Features a durable waterproof "see through" plastic lens that provides you with clear vision of the Tach face. The Tach Bag is the best way to assure all weather protection for your expensive monster Tach. Part# Color Red Blue Yellow Black 15

16 Baja Bug Hood Tie Downs Snap on-snap off. Manufactured from specially compounded rubber to hold your hood firmly in position. Steel hinge and mounting hardware is cad plated to prevent rust and corrosion. Easy to install and can be used on all Baja Bug Front Ends Baja Bug Hood Tie Downs DZUS Buttons NEEDS DESCRIPTION DZUS Style Fastener Button 5681 DZUS Style Mounting Tab with Spring Clip Attached 5682 DZUS Button Removal Tool Chrome Push Rod Tube Protectors Protect your push rod tubes and add luster to your engine. Made from heavy gauge steel and then chrome plated. Easy to install and designed to fit all T-1 engines. Sold in sets to fit one engine Chrome Push Rod Tube Protectors (one pair) Weld In Brackets Heavy gauge steel brackets packaged in sets of four. Weld them on to mount lights, seat belts, or any other number of accessories. The Formed Brackets wrap around the frame to provide the strongest type of mount. These mounts are ideal for use on dune buggies, race cars, and sedans Weld In Brackets - Flat (set of 4) 6596 Weld In Brackets - Formed (set of 4) The mounts have a pre-drilled 1/2" hole. Off Road Side Mount Mirror Designed for Off Road cars traveling through thick brush and trees. The 5 Inch Stainless backed mirror is protected by a 3/4" Stainless tube surround welded to a 1 1/2" half round. Can be held in place by two stainless hose clamps or drilled and bolted in place. For use on 1 1/2" tubing. Drip Rail Mount Mirror Designed to be mounted on the Drip Rail of cars and can be adapted to many other applications. Mounting hardware included. Universal left or right mount Off Road Side Mount Mirror - 5" Diameter Universal Stainless Steel Drip Rail Mount Mirror (aka Peep Mirror) 16