INSTALLATION AND INSTRUCTION MANUAL. The Split Phantom. Undercover Interior LED Lightbar. Models
|
|
- Brice French
- 6 years ago
- Views:
Transcription
1 INSTALLATION AND INSTRUCTION MANUAL The Split Phantom Undercover Interior LED Lightbar ULB21 (Discrete) Models ULB24 (Gen 4 Starburst) IMPORTANT: Please read all of the following instructions before installing your new warning light. PLIT390 REV. C 3/19/10
2 NOTICE Due to continuous product improvements, we must reserve the right to change any specifications and information, contained in this manual at any time without notice. Star Headlight & Lantern Co., Inc. makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Star Headlight & Lantern Co., Inc. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this manual. IMPORTANT: Please read all of the following instructions before installing your new Split Phantom LED undercover lightbar. CAUTION: Please be sure to check that your cigarette plug outlet is properly fused. Testing the light before this fuse is properly installed will void the warranty on the light. WARNING!!!! Care should be taken when positioning this warning light so that the light and/or cord does not interfere with the proper operation of the driver-side or passengerside airbag! Failure to heed this warning may result in serious or fatal injury. Please Note: These instructions are provided as a general guideline only. Specific mounting and/or wiring, may be necessary and are the sole responsibility of the installer. Star Headlight & Lantern Co., Inc. assumes no responsibility for the integrity of the installation for this or any of its products. The Split Phantom uses state-of-the-art Light Emitting Diode (LED) technology. This warning light is comprised of ultra-high intensity LEDs that are operated by a micro-controller to efficiently produce light output with lifetimes up to 100,000 hours. CAUTION: All of our DC powered warning lights are polarity sensitive. These lights are polarity protected only if the appropriate fuse is used. All wires connected to the positive terminal of the battery should be fused at the battery for their rated load. Testing the light before this fuse is properly installed will void the warranty on the light. -1-
3 Optional Mounting Brackets There are six (6) optional mounting brackets that can be used to mount your Split Phantom or Half Phantom. Your light comes with the one that was selected at the time the light was ordered. Please review the diagram below that shows the parts included with each kit. 274-ULB21-U1 Universal Mounting Kit 274-ULB21-CH Dodge Charger Mounting Kit 274-ULB21-CV Frord Crown Victoria Mounting Kit 274-ULB21-EX Ford Explorer Mounting Kit 274-ULB21-IM Chevrolet Impala Mounting Kit 274-ULB21-TA Chevrolet Tahoe Mounting Kit Please Note: Every ULB21 comes with a standard baffle included. The 274- ULB21-CH kit also includes a separate baffle that is specifically designed to fit the 2008 Dodge Charger. It should be used in place of the standard baffle included. -2-
4 Mounting Instructions The following mounting instructions describe the standard, most common way to mount this light. This method may or may not apply to your vehicle. Because vehicles can vary widely in their design, it may be necessary to configure the brackets differently than described. Some applications may require you to design your own custom brackets. The installer assumes all responsibility for the integrity of the installation. It is the sole responsibility of the owner to ensure the light is secure. The Split Phantom is designed to be mounted on the inside of your vehicle. It is not intended for exterior applications and is not warranted against water damage. It is the sole responsibility of the owner to ensure the warning light is secure. Check your light every time you enter the vehicle to ensure that it is mounted securely. The manufacturer assumes no responsibility for the secure mounting of this light. The ULB21 is designed to be mounted in the front windshield of a vehicle using both of the pre-existing visor clips. An alternate method is also shown using the Universal Brackets. Before installing any of the brackets, slide the enclosed rubber channel over the front edge of the baffle. -3-
5 The mounting instructions are divided into two separate sections. If you are using the Universal Mount, proceed below. If you will be using one of the vehicle specific brackets, please skip to page 9. UNIVERSAL BRACKET INSTALLATION (Model 274-ULB21-U1) OR SUCTION CUP WINDOW ADHESIVE MOUNT The Universal Mount use two forked brackets and either a pair of suction cups or a pair of window adhesive mounting pads (both included). The Forked Brackets must be installed for both the suction cup and window adhesive mounts. Determine if you can install the Forked Brackets under your visor clips or if you need to attach them in an alternate fashion and refer to the appropriate section on pages 6 or
6 Universal Mounting (CONT'D) Attach Forked Brackets to Light 1. Insert one of the carriage bolts through one of the washers. Please note that washer is used as a spacer on the square neck of the carriage bolt. Slide the bolt and washer through the back of the left bracket. Be sure to select the correct bracket. The larger flange should be located towards the center of the light. 2. Remove three of the #8 x 1/2" selftapping Phillips pan head screws and use them to install the left attaching bracket on the light. CAUTION: Take extreme caution not to over tighten the screws!!! Over tightening of the screws can strip the holes and result in a faulty mount. 3. Once the left attaching bracket is installed securely on the light, fasten one of the forked L brackets to the attaching bracket, using the carriage bolt, a washer, and a nut. Leave the nut slightly loose to allow for minor adjustments during the remainder of the installation. CAUTION: Take extreme caution not to over tighten the screws!!! Over tightening of the screws can strip the holes. 4. Repeat steps 1-3 for the right attaching bracket. -5-
7 Universal Mounting (CONT'D) Attach Forked Brackets to Visor Clips (If you do not have visor clips, or your visor clips will NOT provide a secure mount, or this method will not work in your vehicle for any other reason, use the alternate method on the next page.) 1. Standard mounting uses the factory installed visor clips already located on the vehicle, in conjunction with the suction cups or window adhesive mounts. If you do not have any visor clips, use the Alternate Mounting section on the next page. 2. Locate the two visor clips on the vehicle. The style may vary from vehicle to vehicle. Some styles use only one screw each, while others may have more. Verify that both visor clips are a minimum of 3 from the center of the window, and a maximum of 8 from the center. 3. Loosen (or remove if necessary) both visor clips enough that one of the forked brackets can easily slide under each of them. 4. Slide one forked bracket under each visor clip and tighten the clip such that it securely holds each bracket in place. 5. Once the brackets are installed securely under the visor clips or with a suitable fastener, check to see that the bottom of the light is level front-to-back. If it is not level, remove the light from the visor clips and carefully bend the forked brackets as necessary. Reinstall the light and check again for levelness. Repeat this process until the light is level. Bend here if necessary -6-
8 Universal Mounting (CONT'D) Attach Forked Brackets using Alternate Method If you are not using the visor clip installation described on the previous page, continue below. 1. Some vehicles may not have visor clips appropriate for the previously described installation, or may completely lack any visor clips. An alternate mounting screw hole is provided in the bracket for these situations. This hole can be used with an appropriate user supplied screw or other suitable fastener. Alternate Mounting Hole 2. If you are using the alternate mounting screw hole, you will need to locate the roof brace under the headliner of the vehicle. 3. Once you have located the roof brace, pick an area to mount the brackets (one on each side) that is a minimum of 3 from the center of your window and a maximum of You must then determine an appropriate size screw to penetrate the headliner and securely mount the brackets to the roof brace. When selecting a screw, take care to ensure that it is capable of supporting the weight of the light and it will not penetrate the roof of the vehicle. 5. Carefully drill any necessary pilot holes in your roof brace. CAUTION: Take care to ensure when selecting a screw and drilling the hole that it is capable of supporting the weight of the light and that it does not penetrate the roof of the vehicle. 6. Install the screws through each bracket. 7. If necessary, adjust your light as described in Step 5 on the previous page. -7-
9 Universal Mounting (CONT'D) Attach The Suction Cups or Window Adhesive Mounts 1. Remove the two #4 x 1/4" Phillips pan head screws on either end of the bar, along with the washers and nylon spacers. Remove outermost screws from bottom of unit. (Bottom View) 2. Use the screws to attach the "L"-Brackets to either end of the light as pictured to the right. You may desire to remove the nylon spacer if the screw does not securely fasten to the base. or CAUTION: Take extreme caution not to over tighten the screws!!! Over tightening of the screws can strip the holes and result in a faulty mount. 3. Then use the appropriate hardware (as shown above) to attach either the Adhesive Pads or the Suction Cups, depending upon your application. If using the window adhesive: Be sure to use the tube of cleaner to clean both surfaces. After applying adhesive, please allow a minimum of 2-5 minutes for the pad to adhere to the window before releasing pressure. Allow 24 hours for the adhesive to fully cure before using. 4. Continue to the BAFFLE ADJUSTMENT section on page
10 VEHICLE SPECIFIC BRACKET INSTALLATION (Models 274-ULB21-CH, 274-ULB21-CV, 274-ULB21-EX, 274-ULB21-IM, and 274-ULB21-TA) 1. Remove both visor clips from the vehicle. 2. Loosen (LOOSEN, DO NOT REMOVE!!) the three visor pivot arm screws on one side of the vehicle with appropriate screwdriver. (Passenger s side shown) 3. Slide the forked end of the visor bracket under the visor pivot arm that you just loosened. (Passenger s side shown) 4. Align the square hole on the other end of the visor bracket with the visor clip hole. (Passenger s side shown) 5. Replace and tighten visor clip to secure the visor bracket to your vehicle. (Passenger s side shown) -9-
11 Vehicle Specific Mounting Brackets (CONT'D) 6. Tighten the screws on the visor arm to hold the visor bracket in place. (Passenger s side shown) 7. Place the angled "L" bracket over the two studs on the visor bracket as shown to the right. Using two #8 washers and two acorn nuts, attach the L bracket to the threaded studs. Note: You may want to leave the acorn nuts slightly loose to allow for easier final adjustments. (Passenger s side shown) 8. Attach the light to the "L" bracket using the two studs protruding from the back of the light housing. Secure the light using two #8 washers and acorn nuts as shown to the right. Note: You may want to leave the acorn nuts slightly loose to allow for easier final adjustments. 4. Align the square hole on the other end of the visor bracket with the visor clip hole. (Passenger s side shown) 9. Loosen the two Baffle Adjustment Screws located on the bottom of the light to allow the baffle to slide. (Driver s side shown) -10-
12 Vehicle Specific Mounting Brackets (CONT'D) 10. With acorn nuts still slightly loose, slide the light as close to the front windshield as possible. Once it is touching the window, tighten the two acorn nuts that secure the two brackets together. 11. Repeat Steps 2-10 for the opposite side of the vehicle. BAFFLE ADJUSTMENT (All Models) 1. After the top of the light is touching the windshield, slide the baffle forward until it satisfactorily blocks any reflected light. 2. Tighten the Baffle Adjusting Screws to secure the baffle in place. CAUTION: Take extreme caution not to over tighten the screws!!! Over tightening of the screws can strip the holes. 3. Once all of the brackets are securely tightened, check your mount to ensure the desired angle is achieved. Stand in front of the vehicle and inspect the light through the front windshield. The screws may be loosened slightly to allow for any final adjustments necessary. 4. After all the necessary adjustments are made retighten all the screws. CAUTION: Take extreme caution not to over tighten the screws!!! Over tightening of the screws can strip the holes and result in a faulty mount.. CAUTION!!! Once the light is secured, route your cord such that it does not interfere with the vision of the driver or the operation of the steering wheel, gear shifter, and/or any airbags. Star Headlight & Lantern Co., Inc. assumes no responsibility for the secure mounting of this light. It is the responsibility of the installer and/or owner to ensure the lightbar is mounted securely. Check your light every time you enter the vehicle to ensure that it is mounted securely. -11-
13 Operating Instructions 3-Way Mode Switch Flashing/Off/Steady Pattern Select / Burst Mode All wires connected to the positive terminal of the battery should be fused at the battery for their rated load. Testing the light before this fuse is properly installed will void the warranty on the light. The Split Phantom is designed for simple operation using two switches. It has a 3-Way Illuminated Mode Switch and a Pattern Select/Burst Mode Button. The 3-Way Mode Switch (Flashing/Off/Steady or Pursuit/Off/Takedown) This switch is located closest to the driver's side. It is used to select which mode The Split Phantom will operate in. While in the Steady (Takedown) mode, the LEDs will not flash, but instead will remain lit, similar to Takedown lights. Under the Flashing (Pursuit) mode, the LEDs will flash according to the pattern you have selected (See Flashing (Pursuit) Mode below). Indicator LED Located on the bottom of the right half (passenger side) of the Split Phantom is an Indicator LED. When your light is activated in any mode, this LED will light up. Pattern Select/Burst Mode Button The button located on the inside edge of the passenger half (see diagram above) is the Pattern Select/Burst Mode button. This is a momentary switch and has two different functions, depending upon which mode the 3-Way Mode Switch is in. 3-Way Mode Switch set for Steady (Takedown) Mode: If the 3 -way mode switch of your Split Phantom is in the Steady Mode position, the Pattern Select/Burst Mode will burst your LEDs into a super-bright, high-power mode (takedowns). This mode will activate for approximately 30 seconds then revert to the standard steady burn mode. Please Note: Immediately after the 30 second Burst Mode has ended, the light will be locked out of Burst Mode for 30 seconds. 3-Way Mode Switch set for Flashing (Pursuit) Mode: If the 3-way mode switch of your Split Phantom is in the Flashing Mode position, the Pattern Select/Burst Mode will act as the Pattern Select button. Each time this switch-button is depressed, the Split Phantom will cycle to the next pattern. The Split Phantom is designed with thirty-five different patterns (see next page): -12-
14 1 Slow Warn * 2 Fast Warn 3 Superfast Warn 4 Warn Fade 5 Pre-Pop Warn 6 All Singleflash 7 Alt. Tripleflash 8 All Tripleflash 9 Alt. Quadflash w/post Pop 10 All Quadflash w/post Pop 11 Alt. Quintflash 12 All Quintflash 13 Alt. Pre-pop Quintflash 14 All Flicker 15 Alt. PSU Flicker 16 One Side Pop, Other Side Rapid Fire 17 One Side Rapid Fire, Other Pop 18 Comet 1 19 Comet 2 20 Delta Omega (Flash Rate Sweep) 21 Slow Warn, Superfast Warn 22 All Singleflash, All Flicker 23 Alt. Double, ALT. Quad w/post Pop 24 All Double, ALL. Quad w/post Pop 25 Alt Double, Alt. Pre-Pop Quad, Alt. Quad w/post Pop, Alt Flicker 26 All Double, All Quintflash, All Quadflash w/post Pop, All Flicker 27 All Quadflash w/post Pop, All Doubleflash, All Flicker 28 Alt. Pre-Pop Triple, Alt. Doubleflash, Alt Flicker ** 29 Alt. Pre-Pops, Alt. Flicker, Superfast Warn 30 Delta Omega, All. Double, All. Flicker 31 One Side Steady---Other side Singleflash 32 One Side Steady---Other Side Short-Long 33 Warn Medium (Alt. Long Singleflash) 34 Alt. Short - Alt. Long 35 Cycle All = These Patterns meet California Title 13 and SAE J595 specifications in Red and Blue versions of the model ULB42 only. (ULB42V models DO NOT meet these specs) * Default Pattern #1 ** Default Pattern #2 Pattern List If at anytime you would like to go directly to the Slow Warn (pattern #1), simply press, and hold the pattern select button for approximately 3 seconds. When the LEDs flash once, release the button and the light will be in the Slow Warn pattern. If you would like to place the light back into the default pattern (Pattern 28: Alt. Pre-Pop Triple, Alt. Doubleflash, Alt Flicker), simply press and hold the pattern select button until the LED s flash twice (approx. 6 seconds). Then release the button and the light should be in the default pattern. Toggle Mode: Pressing and holding the pattern select button until the LED s flash three times (approx. 9 seconds) will toggle the steady side for patterns 31 and 32. The Split Phantom will remember the pattern it was in when turned off and display the same pattern when re-activated. -13-
15 Once your Split Phantom is installed, please test all the patterns and options to familiarize yourself with the various patterns and the operation of the buttons. If you have any questions concerning this or any other product, please contact our Customer Service Department at (585)
16 These lights use state-of-the-art Light Emitting Diode (LED) technology. These warning lights are comprised of ultra-high intensity LEDs that are controlled by a solid state flasher unit to efficiently produce light output with lifetimes up to 100,000 hours. Under normal circumstances, you will not need to replace any LEDs in this light. If any of the LED's in your light do fail, please contact Star Headlight for arrangements to have them repaired. The flasher unit and heads CANNOT be serviced in the field and any attempt to do so will void the warranty. LED FIVE YEAR LIMITED WARRANTY The manufacturer warrants this LED light against factory defects in material and workmanship for five years after the date of purchase. The owner will be responsible for returning to the Service Center any defective item(s) with the transportation costs prepaid. The manufacturer will, without charge, repair or replace at its option, products, or part(s), which its inspection determines to be defective. Repaired or replacement item(s) will be returned to the purchaser with transportation costs prepaid from the service point. A copy of the purchaser's receipt must be returned with the defective item(s) in order to qualify for the warranty coverage. Exclusions from this warranty include, but are not limited to, domes, and/or the finish. This warranty shall not apply to any light, which has been altered, such that in the manufacturer's judgment, the performance or reliability has been affected, or if any damage has resulted from abnormal use or service. There are no warranties expressed or implied (including any warranty of merchantability or fitness), which extend this warranty period. The loss of use of the product, loss of time, inconvenience, commercial loss or consequential damages, including costs of any labor, are not covered. The manufacturer reserves the right to change the design of the product without assuming any obligation to modify any product previously manufactured. This warranty gives you specific legal rights. You might also have additional rights that may vary from state to state. Some states do not allow limitations on how long an implied warranty lasts. Some states do not allow the exclusion or limitation of incidental or consequential damages. Therefore, the above limitation(s) or exclusion(s) may not apply to you. NOTE: Most failures can be traced to wiring and battery problems. Check "quick-connects and wiring to insure that correct voltage/polarity is reaching the electronic strobe light/led beacon. If you have any questions concerning this or any other Star product, please contact our Customer Service Department at (585) If a product must be returned for any reason, please contact our Customer Service Department to obtain a Returned Goods Authorization number (RGA #) before you ship the product to Star. Please write the RGA # clearly on the package near the mailing label. -15-
INSTALLATION AND INSTRUCTION MANUAL. The Split Phantom. Undercover Interior LED Lightbar. Models
INSTALLATION AND INSTRUCTION MANUAL The Split Phantom Undercover Interior LED Lightbar ULB21 (Discrete) Models ULB24 (Gen 4 Starburst) IMPORTANT: Please read all of the following instructions before installing
More informationINSTALLATION AND INSTRUCTION MANUAL. The Split Phantom. Undercover Interior LED Lightbar. Models ULB21 ULB24 (Discrete) (Gen 4 Starburst)
INSTALLATION AND INSTRUCTION MANUAL The Split Phantom Undercover Interior LED Lightbar Models ULB21 ULB24 (Discrete) (Gen 4 Starburst) IMPORTANT: Please read all of the following instructions before installing
More informationINSTALLATION AND INSTRUCTION MANUAL. The Split Phantom
INSTALLATION AND INSTRUCTION MANUAL The Split Phantom Undercover Interior LED Split Lightbar With Generation-4 LED Takedown and Directional Pursuit Lights Models ULB21-DLP ULB24-DLP (Discrete) (Gen 4 Starburst)
More informationINSTALLATION AND INSTRUCTION MANUAL
INSTALLATION AND INSTRUCTION MANUAL Star Mini Phantom Models ULB9 and ULB9-1 35-Pattern Undercover Interior Mini LED Light PLITSTR46 REV. F 7/14/10 IMPORTANT: Please read all of the following instructions
More informationMODEL DL35-CV LED REAR DECK LIGHT
TM MODEL DL35-CV LED REAR DECK LIGHT PLITSTR374 REV. A 8/4/06 Please Note: These instructions are provided as a general guideline only. Specific mounting, wiring, and/or weather-sealing may be necessary
More informationLineum Star Split Phantom. Model ULB28. Dual Color Undercover Interior LED Lightbar PLIT507 REV. - 3/20/14
Lineum Star Split Phantom Model ULB28 Dual Color Undercover Interior LED Lightbar PLIT507 REV. - 3/20/14 IMPORTANT: Please read all of the following instructions before installing your new warning light.
More informationLineum Star Phantom Model ULB48-TD
Lineum Star Phantom Model ULB48-TD Dual Color Undercover Interior LED Lightbar IMPORTANT: Please read all of the following instructions before installing your new warning light. Please Note: These instructions
More informationStar Mini Phantom. Interior Undercover Mini LED Light. PATENTS D530,029 and D632,421. ULB9E Series
Star Mini Phantom Interior Undercover Mini LED Light PATENTS D530,029 and D632,421 ULB9E Series IMPORTANT: Please read all of the following instructions before installing your new light. CAUTION: Please
More informationStar Mini Phantom. Interior Undercover Mini LED Light. PATENTS D530,029 and D632,421. ULB9S Series (Starburst LEDs)
Star Mini Phantom Interior Undercover Mini LED Light PATENTS D530,029 and D632,421 ULB9 Series (Discrete LEDs) ULB9S Series (Starburst LEDs) IMPORTANT: Please read all of the following instructions before
More informationStar Mini Phantom. Interior Undercover Mini LED Light. PATENTS D530,029 and D632,421. ULB9LDC Series (Lineum LED Dual Color)
Star Mini Phantom Interior Undercover Mini LED Light PATENTS D530,029 and D632,421 ULB9LDC Series (Lineum LED Dual Color) IMPORTANT: Please read all of the following instructions before installing your
More informationHalo LED Lights 200, 240, 250, 255, 257, and 258 Series
INSTALLATION AND INSTRUCTION MANUAL Halo LED Lights 200, 240, 250, 255, 257, and 258 featuring the 200SHL/200SH8L SERIES 200BHL/200BH8L SERIES 255/257/258 "S" 240HSL / 240H8SL 240HSFL / 240H8SFL 250HSL
More informationPlus SABRE LIGHTBARS
INSTALLATION AND INSTRUCTION MANUAL Plus SABRE LIGHTBARS Models 5364LED, 5462LED, 5464LED and 5564LED PLIT445 REV. D 2/2/18 Keep any radio frequency sensitive equipment at least 20 from the bar and power
More informationEnhanced Mini Phantom
Enhanced Mini Phantom Undercover Interior Mini Enhanced LED Light DL086 DL451 GR152 (Single Head) (w/cig Plug) (Dual Head) (w/cig Plug) (Dual Head) (w/hard Wire) IMPORTANT: Please read all of the following
More informationINSTALLATION AND INSTRUCTION MANUAL
INSTALLATION AND INSTRUCTION MANUAL and STAR SABRE ECE Compliant Plus Lightbars PLIT429ECE REV. C 3/31/14 Please Note: These instructions are provided as a general guideline only. Specific mounting, wiring,
More informationINSTALLATION AND INSTRUCTION MANUAL
INSTALLATION AND INSTRUCTION MANUAL Models 2364LED, 2464LED and 2564LED Plus Lightbars PLIT429 REV. D 11/11/13 When mounting your lightbar, please be sure to keep any radio frequency sensitive equipment
More informationTD77-2 and ULB42-TD-2 TRAFFIC DIRECTOR CONTROL BOXES
TD77-2 and ULB42-TD-2 TRAFFIC DIRECTOR CONTROL BOXES Important: This product is used to direct traffic. Improper use may result in vehicular collision, personal injury and/or death. Star Headlight & Lantern
More informationModel RP310 Owner's Manual & Installation Instructions
INSTALLATION AND INSTRUCTION MANUAL REMOTE STROBE PACK Model RP310 Owner's Manual & Installation Instructions PLITSTR223 REV. B 3/3/11 Table of Contents SAFETY WARNINGS 1 MOUNTING 2 WIRING INSTRUCTIONS
More informationTDDL15 and TDLIN Series
TDDL15 and TDLIN Series TRAFFIC DIRECTORS TDDL15-36 Series TDDL15-42 Series TDDL15-47 Series TDLIN-47 Series TDLIN-36 Series PLITSTR192 REV. E 3/10/16 Please Note: These instructions are provided as a
More informationHalo LED Lights 200, 240, 250, 255, 257, and 258 Series
INSTALLATION AND INSTRUCTION MANUAL Halo LED Lights 200, 240, 250, 255, 257, and 258 featuring the 200SHL/200SH8L SERIES 200BHL/200BH8L SERIES 255/257/258 "S" 240HSL / 240H8SL 240HSFL / 240H8SFL 250HSL
More informationINSTALLATION AND INSTRUCTION MANUAL
INSTALLATION AND INSTRUCTION MANUAL PLITSTR341 REV G 12/2/13 When mounting your lightbar, please be sure to keep any radio frequency sensitive equipment at least 20 from the bar and power cable(s). This
More informationINSTALLATION AND INSTRUCTION MANUAL
INSTALLATION AND INSTRUCTION MANUAL Ultra Low Profile Modular Lightbar PLIT414 REV. F 3/2/17 It is the sole responsibility of the owner to ensure the lightbar is mounted securely. Check your light every
More informationINSTALLATION AND INSTRUCTION MANUAL
INSTALLATION AND INSTRUCTION MANUAL PLITSTR341 REV E 6/15/09 When mounting your lightbar, please be sure to keep any radio frequency sensitive equipment at least 20 from the bar and power cable(s). This
More informationFUSION Model # - FN-XXXX, *See website for Part # Fusion Innerbar. Instruction Manual V2.0
Fusion Innerbar Instruction Manual FUSION Model # - FN-XXXX, *See website for Part # This instruction manual serves as a guide for the Fusion Innerbars. IMPORTANT! Please read through all provided instructions
More informationFENIEX ROCKER PANEL Series MODEL # D-11971
www.feniex.com E-mail: Support@feniex.com Support line: 1.800.615.8350 Installation and Operational Guide FENIEX ROCKER PANEL Series MODEL # D-11971 This instruction manual serves as a guide for the Rocker
More informationCOBRA Model # - D X, D X, D-20109, D-20209, D-20409, D20609, D-20809, D-21015, D-20119, D Cobra Series- Instruction Manual V.
V3.0 Cobra Series- Instruction Manual V.3 COBRA Model # - D-20109-1X, D-20215-2X, D-20109, D-20209, D-20409, D20609, D-20809, D-21015, D-20119, D-21109 This instruction manual serves as a guide for the
More informationFN-4918 INSTRUCTION MANUAL SCAN HERE
FENIEX // 2018 // INSTRUCTION MANUAL Is this the latest version? SCAN HERE FN-4918 INSTRUCTION MANUAL Feniex Product Copyrights This price List and the mentioned Feniex products include or describe copyrighted
More informationINSTALLATION AND INSTRUCTION MANUAL
INSTALLATION AND INSTRUCTION MANUAL TM Aerostar PLITSTR335 REV. G 8/16/12 Please Note: These instructions are provided as a general guideline only. Specific mounting, wiring, and/or weather-sealing may
More informationGEN 3 LED LIGHT BAR INSTALLATION MANUAL Model 7840-A 44"
GEN 3 LED LIGHT BAR INSTALLATION MANUAL Model 7840-A 44" Your purchase of a Wolo warning light bar is the perfect choice to compliment your vehicle. Wolo s warning lights are manufactured with the finest
More informationThank you for purchasing a 911EP GALAXY Light Bar! Every light bar is carefully inspected for defects prior to shipment.
OWNER S MANUAL Safety First Thank you for purchasing a 911EP GALAXY Light Bar! Every light bar is carefully inspected for defects prior to shipment. Questions or Concerns? 911EP wants to quickly resolve
More informationOperating Instructions & Parts Manual. Fuel Tank Adapter
Operating Instructions & Parts Manual Fuel Tank Adapter Model Number 40080 Capacity 80 lb.! This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety
More informationDo not install and/or operate this safety product unless you have read and understand the safety information contained in this manual.
Installation and Operation Instructions MR Tri- Light Available in various color combinations, the MR Directional LED surface mount, tri-color warning light is ideal for a wide variety of auxiliary warning
More informationINSTALLATION & OPERATION MANUAL
INSTALLATION & OPERATION MANUAL SuperVisorTL IMPORTANT: SuperVisorTL Interior Lighting System 2011 Ford F150 CONTENTS: Introduction... 2 Unpacking & Pre-Installation...2 Installation & Mounting...3-4 Wiring
More informationProper installation of this product requires the installer to have a good understanding of automotive electronics, systems and procedures.
ENGINEERING COMPANY INC. 51 Winthrop Road Chester, Connecticut 06412-0684 Phone: (860) 526-9504 Fax: (860) 526-4078 Internet: www.whelen.com Sales e-mail: autosale@whelen.com Canadian Sales e-mail: autocan@whelen.com
More informationOwner's Manual & Installation Instructions PLITSTR335 REV. F 11/1/07
Aerostar TM Owner's Manual & Installation Instructions PLITSTR335 REV. F 11/1/07 CAUTION: All of our DC powered warning lights are polarity sensitive. These lights are polarity protected only if the appropriate
More informationINSTALLATION & OPERATION MANUAL
INSTALLATION & OPERATION MANUAL SUPERVISOR TL SuperVisor TL Interior Lighting System Expedition 2007 Model CONTENTS: Introduction... 2 Unpacking & Pre-Installation... 2 Installation & Mounting... 3-4 Wiring
More informationPlease read BOTH these Installation Instructions and the General Information sheet prior to installing or operating this equipment.
Attachment Tab Height: 24-1/4 Serial Number Attachment Tab Width: 24 Please read BOTH these and the General Information sheet prior to installing or operating this equipment. 1. Blue Ox towing products
More informationAPOLLO Model # - F-12013, F-22013, D-50115, D-50215, D-50415, D-50615, D-50815, D Apollo Series- Instruction Manual V.3
Apollo Series- Instruction Manual V.3 APOLLO Model # - F-12013, F-22013, D-50115, D-50215, D-50415, D-50615, D-50815, D-51015 This instruction manual serves as a guide for the Apollo Series. IMPORTANT!
More informationINSTALLATION & OPERATION MANUAL. WingMan. WingMan. Interior Lighting System FORD CROWN VICTORIA UPPER REAR DECK LIGHT BAR IMPORTANT: CONTENTS:
INSTALLATION & OPERATION MANUAL WingMan CONTENTS: WingMan Interior Lighting System FORD CROWN VICTORIA UPPER REAR DECK LIGHT BAR Introduction... 2 Unpacking & Pre-Installation... 2 Installation & Mounting...
More informationFUSION Model # - L-4910 L Fusion 49 and 60 Light Bar Instruction Manual V2.0. This instruction manual serves as a guide for the Fusion Lightbar.
FENIEX. 2016 INSTRUCTION MANUAL Fusion 49 and 60 Light Bar Instruction Manual 49 60 FUSION Model # - L-4910 L-6010 This instruction manual serves as a guide for the Fusion Lightbar. IMPORTANT! Please read
More informationThis document describes:
Thank you for purchasing this product from ERM. We appreciate your interest in our unique product line as we try to offer our customers an alternative to today s traditional products. This programmable
More informationInstallation Instructions Soft Top Replacement Hardware, Wrangler
Installation Instructions Soft Top Replacement Hardware, 87-95 Wrangler IMPORTANT NOTICE: Carefully read instructions before attempting to install this product. Rampage is in no way responsible for any
More informationBP1204 INSTALLATION/OWNER'S MANUAL
BP1204 INSTALLATION/OWNER'S MANUAL BP1204 PREPARATION Getting Started Thank you for purchasing the Dual Electronics BP1204 Bandpass Subwoofer System. Although Dual has attempted to ensure the information
More informationINSTALLATION/OWNERS MANUAL
INSTALLATION/OWNERS MANUAL XOBP12D PREPARATION Getting Started Thank you for purchasing the Dual Electronics XOBP12D Bandpass Subwoofer System. Although Dual has attempted to make sure all of the information
More informationInstruction set # 7068 Cognito Motorsports, Inc. Upper Control Arm Leveling Kit for GM 8-Lug #UCAK (Boxed Style)
Cognito Motorsports, Inc. Upper Control Arm Leveling Kit for 2001-2010 GM 8-Lug #UCAK100010 (Boxed Style) Introduction - These control arms will not affect the height of the truck, the height is determined
More informationWARNING. BX Buick Lacrosse Installation Instructions. Bolt Torque Specifications. Bolt Torque Specifications
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationINSTALLATION & OPERATION MANUAL. WingMan. WingMan IMPORTANT: Interior Lighting System Crown Victoria REAR DECK LIGHT BAR
INSTALLATION & OPERATION MANUAL SHORT VERSION WingMan LONG VERSION WingMan Interior Lighting System Crown Victoria REAR DECK LIGHT BAR CONTENTS: Introduction... 2 Unpacking & Pre-Installation... 2 Installation
More informationInstruction Sheet SRSR SERIES. Rotating Sliding Rail System
Instruction Sheet SRSR SERIES Rotating Sliding Rail System THANK YOU Thank you for purchasing the SRSR Series Rotating Sliding Rail System. Please read these instructions thoroughly before assembling this
More informationIMPORTANT: Follow these instructions BEFORE installing the Retrax cover
#2011 Install Instructions Supplement IMPORTANT: Follow these instructions BEFORE installing the Retrax cover Note: Use caution when cutting the wire ties holding the wire harness together so you do not
More informationFUSION Model # - L-4910 L Fusion 49 and 60 Light Bar Instruction Manual V.1. This instruction manual serves as a guide for the Fusion Lightbar.
Fusion 49 and 60 Light Bar Instruction Manual V.1 49 60 FUSION Model # - L-4910 L-6010 This instruction manual serves as a guide for the Fusion Lightbar. IMPORTANT! Please read through all provided instructions
More informationCA611 Owners Manual CAUTION!
CA611 Owners Manual CAUTION! Be certain that the vehicle is outdoors before using this or any remote vehicle starting device. A running engine produces dangerous carbon monoxide fumes which can be harmful
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. Attachment Tab Height: 19-1/2 Serial Number Attachment Tab Width: 19 Please read BOTH these and the General Information
More informationEasy/Tran TF STANDBY POWER FURNACE SWITCH TOOLS NEEDED FOR INSTALLATION. PARTS LIST for Easy / Tran TF FURNACE TRANSFER SWITCH
STANDBY POWER FURNACE SWITCH Easy/Tran TF Congratulations on your purchase of the Reliance Controls Easy/Tran TF furnace transfer switch. Reliance has been manufacturing transfer switches and equipment
More informationInstallation Instructions **THIS RAIL MOUNTING KIT USES 11 BOLTS**
Installation Instructions CUSTOM QUICK INSTALL MOUNTING KIT FORD SUPER DUTY Part Numbers: 50074 WARNING:Under no circumstances do we recommend exceeding the towing vehicle manufacturers recommended vehicle
More informationFusion GPL 49 Instruction Manual
FENIEX. 2018 INSTRUCTION MANUAL Fusion GPL 49 Instruction Manual 49 This instruction manual serves as a guide for the Fusion 49 GPL. Model # FN-4916 IMPORTANT! Please read through all provided instructions
More informationSafety, Installation and Service Manual Models 1952, 1953 & 1972
Ultraviolet Germicidal Lamps Model 1952 24 Rooftop Unit Model 1953 32 Rooftop Unit Model 1972 Rooftop Unit, Internal Mount Safety, Installation and Service Manual Models 1952, 1953 & 1972 READ AND SAVE
More informationMega-Flow External Damper Fans
Mega-Flow External Damper Fans With Cone Owner s Manual Hired-Hand, Mfg., Inc. PO Box 140 1733 County Road 68 Bremen, Alabama 35033 Part No. 4801-5402 Rev 4/08 Owners Manual Mega-Flow External Damper Fans
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16, 10mm, 18mm Drill Bits: 1/4 Other Tools: Drill, Reciprocating saw 9465/9475 HIDE-A-GOOSE HITCH INSTALLATION All Fasteners Typical, Both Sides WARNING:
More informationLIBERATOR USER MANUAL
LIBERATOR USER MANUAL TABLE OF CONTENTS Specifications... 1 Battery Installation... 3 Components... 4 Basic Functions... 5 Lockout/Ready Mode... 8 Momentary Mode... 8 Constant-On... 9 Cycle Control...
More informationSTC2 Car Kit. Installation Guide
STC2 Car Kit Installation Guide Box Contents When you unpack your STC2 Car Kit, it should include everything as shown below: Suction Cup Mount & Screws Surface Preparation Cleaning Kit (To clean a surface
More informationHARDWARE KIT INSTALLATION GLOVES
COIL MOUNT STEEL DUCT MOUNT DUCTBOARD MOUNT CLAMP PLATE Z-BRACKET PCO BRACKET SHIELDED LAMP ASSEMBLY ALSO INCLUDED BALLAST TECH MANUAL HARDWARE KIT INSTALLATION GLOVES Rev 1 Issued: 09/03/2014 SERVICE
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. 2015-18 Ford Edge (Includes ACC) (No 2.0L EcoBoost or Sport) Attachment Tab Height: 15 Serial Number Attachment Tab
More informationINFINITY-3 STROBE LED BAR INSTALLATION MANUAL 7700 SERIES
INFINITY-3 STROBE LED BAR INSTALLATION MANUAL 7700 SERIES Your purchase of a Wolo warning light is the perfect choice to compliment your vehicle. Wolo s warning lights are manufactured with the finest
More informationINSTALLATION INSTRUCTIONS MOUNTING KIT FOR ELITE SERIES
INSTALLATION INSTRUCTIONS MOUNTING KIT FOR ELITE SERIES DO NOT EXCEED VEHICLE MANUFACTURER S RATING FOR 5th WHEEL TOWING OR MAXIMUM GROSS TRAILER WEIGHT OF 18,000lb. / 8160kg. DEALER/INSTALLER: (1) Provide
More informationInstallation and Operation Instructions C5550 Series LED Microbars
Installation and Operation Instructions C5550 Series LED Microbars C5550 Series - Reflex LED microbars provide a compact yet powerful warning solution that offers the flexibility of either permanent, or
More informationBX Jeep Liberty Renegade 2012 Jeep Liberty Sport Installation Instructions
Attachment Tab Height: 17.5 Attachment Tab Width: 24 Serial Number Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and accessories
More informationFX817 INSTALLATION & OPERATION MANUAL IMPORTANT:
INSTALLATION & OPERATION MANUAL FX817 Contents: Introduction...2 Features and Specifications...2 Current Draw...2 Installation & Mounting...3 Wiring...3 Operation...4 Maintenance...4 Troubleshooting...4
More informationINSTALLATION & OPERATION MANUAL
INSTALLATION & OPERATION MANUAL LED Duo Beam TM Introduction... 2 Unpacking & Pre-Installation...2 Installation & Mounting... 3 Wiring Instructions... 4 Maintenance... 4 Options & Specifcations...5-6 Flash
More informationThis document describes:
Thank you for purchasing this product from ERM Products. We appreciate your interest in our unique product line as we try to offer our customers an alternative to today s traditional products. This universal
More information04 & 14 F FRONT 1.0 REAR LEVELING KIT INSTALLATION
INSTRUCTION PART NO 15312 KIT NO 3836 04 & 14 F-150 2.0 FRONT 1.0 REAR LEVELING KIT INSTALLATION READ INSTRUCTIONS COMPLETELY THROUGH BEFORE STARTING. FAILURE TO ADHERE TO THE INSTRUCTIONS WILL VOID ANY
More informationSABRE LIGHTBARS. Owner's Manual & Installation Instructions. Made In USA. (RP248-L Version) PLITSTR325 REV. D 3/31/05
SABRE LIGHTBARS Owner's Manual & Installation Instructions (RP248-L Version) Made In USA PLITSTR325 REV. D 3/31/05 This page intentionally left blank. Table of Contents WARNINGS 2 MOUNTING BRACKET PARTS
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. BX3796 Attachment Tab Height: 13-1/2 Serial Number Attachment Tab Width: 24 Please read BOTH these and the General
More informationINSTALLATION MANUALS FOR THE SUPERVISOR. Click below to go to the appropriate model. For all others, contact Customer Service at (314)
INSTALLATION MANUALS FOR THE SUPERVISOR Click below to go to the appropriate model. For all others, contact Customer Service at (314) 426-2700. Ford Crown Victoria Chevy Impala Ford Explorer Chevy Tahoe
More informationModel AS-RC3260 TV Cart. Rolling Cart for Audio Mount System & Flat Panel TVs
Model AS-RC3260 TV Cart Rolling Cart for Audio Mount System & Flat Panel TVs GETTING STARTED Introduction Congratulations on the purchase of your new Helios AS-RC3260 Rolling Cart. For maximum benefit,
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 15/16, 15/16 Crowfoot Adaptor Drill Bits: 1/4 Other Tools: Drill, Reciprocating saw Optional, Raise Bed: 18mm socket, 15 extension As an option you can loosen
More informationModel A Turn Signal Kit Installation Guide
Model A Turn Signal Kit Installation Guide Creative Connections, Inc. Consumer Hot Line: 888-471-LOGO 770-476-7322 In Atlanta, GA http://www.logolites.com P/N: 100-005/K 2008 Creative Connections, Inc.
More informationINFINITY-1 HALOGEN LIGHT BAR INSTALLATION MANUAL 7000 SERIES
INFINITY-1 HALOGEN LIGHT BAR INSTALLATION MANUAL 7000 SERIES Your purchase of a Wolo warning light is the perfect choice to compliment your vehicle. Wolo s warning lights are manufactured with the finest
More informationHANDY GATE ASSEMBLY, INSTALLATION AND OPERATING INSTRUCTIONS
ASSEMBLY, INSTALLATION AND OPERATING INSTRUCTIONS BEFORE INSTALLING OR USING THE, REVIEW THE VEHICLE LOADING LIMITATIONS OUTLINED IN THE VEHICLE OWNER S MANUAL AND THE SAFETY COMPLIANCE CERTIFICATION LABEL
More informationUniversal Gear Shift Sender for use with Lokar Indicators GSS-1000-LOK The easiest system to install and use on the market.
Universal Gear Shift Sender for use with Lokar Indicators GSS-1000-LOK The easiest system to install and use on the market. GSS-1000 DECODER N.S. relay B.U. PWR Dim GND Safety Backup Power Dim Park Reverse
More informationadvanced FLOW engineering Instruction Manual P/N: TA-3016P
advanced FLOW engineering Instruction Manual P/N: TA-3016P Make: Infiniti Model: G37 Coupe Year: 2008-2013 Engine: V6-3.7L Make: Infiniti Model: Q60 Year: 2014 Engine: V6-3.7L (EO Exempt 2008-2013 only)
More informationSport Sway Bar Kit (22425) Scion tc
Sport Sway Bar Kit (22425) Scion tc Thank you for your purchase from our new line of Scion tc parts. Please call us at (877) 4NO - ROLL if you have any questions regarding the service or installation of
More informationWARNING. Serial Number
1999NS-2007 Chevrolet & GMC Pickup 1500 Classic (2WD & 4WD, No Heavy Duty) Please read BOTH these Installation Instructions and the Baseplate General Towing Instructions before attempting to install or
More informationInstallation Instructions
Equipment Required: Fastener Kit: F Wrenches: 15/16, 15/16 Crowfoot Adaptor Drill Bits: 1/4 Other Tools: Drill, Reciprocating saw Optional, Raise Bed: 18mm socket, 15 extension As an option you can loosen
More informationUNIVERSAL CUSTOMIZABLE MUD FLAP INSTALLATION INSTRUCTIONS
UNIVERSAL CUSTOMIZABLE MUD FLAP INSTALLATION INSTRUCTIONS Thank you for purchasing ROCKSTARTM Splash Guard Mud Flaps. Agri-Cover, Inc. proudly manufactured these mud flaps using superior quality materials
More informationINSTALLATION CLAMP-ON FORK MOUNTED DRIVING LIGHTS 5015
CLAMP-ON 5015 PARTS INCLUDED 2 Driving Lights 2 Side Mount Clamps-43mm/49mm 1 Hardware Kit Including: 2 49mm Spacers 4 43mm Spacers 2 Pivot Dome Washers 2 3/8-16 Serrated Hex Nut 1 Wiring Kit for Driving
More informationUSB Charge Port Installation Instructions
USB Charge Port Installation Instructions Lifetime Technical Support support@logolites.com 770-476-7322 www.logolites.com Manual 100-0014C Thank you for purchasing a Logo Lites USB Charge Port! USB Charge
More informationINSTALLATION INSTRUCTIONS
THANK YOU FOR CHOOSING KURYAKYN! Protect yourself and others from possible injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices regarding the installation,
More informationINSTALLATION TURN SIGNAL MIRRORS 1432
1432 PARTS INCLUDED 1 Left Side Turn Signal Mirror Assembly with Convex Glass 1 Right Side Turn Signal Mirror Assembly with Convex Glass 1 Hardware Kit, Including: 2 5/16-18 X 1-1/2 Socket Head Cap Screws
More informationINSTALLATION INSTRUCTIONS FOR MOUNTING HARDWARE KIT F-105K2.5
MY SAFE T PLUS UNIT INSTALLATION INSTRUCTIONS FOR MOUNTING HARDWARE KIT F-105K2.5 This kit supports installation of SAFE T PLUS : MODEL # 41-140 (RED) MODEL # 41-180 (WHITE) MODEL #41-230 (BLUE) KEEP INSTRUCTIONS
More informationInstallation Instructions and Warranty Information
Installation Instructions and Warranty Information 1625S 96-98 Mustang 4.6L 2v 1-1/2 1625S-8 96-98 Mustang 4.6L 2v 1-5/8 1625S-1 99-04 Mustang 4.6L 2v 1-1/2 1625S-9 99-04 Mustang 4.6L 2v 1-5/8 1625S-5JT
More informationInstallation Instructions GOOSENECK MOUNTING KIT Chevrolet/GMC 1500/2500/3500 All except 4-door Crew-Cab
GOOSENECK MOUNTING KIT Equipment Required: Fastener Kit: F Wrenches: 3/4, 7/8, 15/16 Drill Bits: 1/4 Other Tools: Drill WARNING: Under no circumstances do we recommend exceeding the towing vehicle manufacturers
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. Attachment Tab Height: 17-3/4 Attachment Tab Width: 18 Serial Number BX1708 2013-16 GMC Acadia (Includes Denali) 2017
More informationInstallation Instructions
Installation Instructions CUSTOM QUICK INSTALL MOUNTING KIT 2011 & UP Ford Super Duty F-250/F-350/F-50 2011 & UP Part Number: 50073 WARNING: Under no circumstances do we recommend exceeding the towing
More informationCognito Motorsports, Inc. Upper Control Arm Kit for 2011-Present GM 8-Lug #UCAK100051
Cognito Motorsports, Inc. Upper Control Arm Kit for 2011-Present GM 8-Lug #UCAK100051 Introduction - Installation requires a qualified mechanic. - Read instructions carefully and study the pictures (if
More informationInstallation Instructions READ THOROUGHLY BEFORE BEGINNING Signature Series Rail Kit Dodge Ram Trucks-all, including Mega-cabs
INDEX Failure to follow all of these instructions may result in death or serious injury!. GUIDELINES FOR MATCHING TOW VEHICLE AND TRAILER. Pages -. DRILLED AND BOLTED INSTALLATION FIGURE. Page 4. NO-DRILL,
More informationCSA CERTIFIED Conforms to UL 507
Installation tion Instructions Please read and save these instructions! TURBO/MAXX12 Volt All Weather RV Ventilator Fans P/N 00-965001 Deluxe Model 1200T WITH THERMOSTAT P/N 00-965007 Standard Model 3550
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. Attachment Tab Height: 21 Serial Number Attachment Tab Width: 31.25 Please read BOTH these and the General Information
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. 2011-16 Mini Cooper Countryman (Includes S) Attachment Tab Height: 14 Serial Number Attachment Tab Width: 20 Please
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. BX2643 Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue
More informationINSTALLATION INSTRUCTIONS MOUNTING KIT FOR ELITE SERIES
INSTALLATION INSTRUCTIONS MOUNTING KIT FOR ELITE SERIES DEALER/INSTALLER: (1) Provide this Manual to end user. END USER: (1) Save this Manual for future reference. (2) Pass on copies of Manual to any other
More informationP/N Deluxe Model 1200T WITH THERMOSTAT P/N Standard Model 3550 WITHOUT THERMOSTAT
Read and Save These Instructions From MaxxAir Vent Corporation TURBO/ MaxxAir the leader in RV ventilation 215120 CSA approved. Complies with UL507 TURBO/MAXX 12 Volt Installation Instructions P/N 00-965001
More information