DPS Telecom Your Partners in Network Alarm Management
|
|
- Verity Curtis
- 6 years ago
- Views:
Transcription
1 DPS Telecom Your Partners in Network Alarm Management Using the Thermalogic Temp Sensor Instructions for Using the Thermalogic Temperature Sensor with a NetGuardian This document is to be used for installation and configuration of the Thermologic Temperature Sensor (Model: WA ). With power removed from unit make necessary connections. Note: The Thermologic temperature sensor is to be powered by a supply voltage ranging from 9 VDC to 24 VDC. The 2.7K Ohm resistor in line with the power is used so that the same supply (48Vdc) used to power the NetGuardian 216 can be used to power the sensor. a. Connect Ground to (+) of sensor. b. Connect (-) from sensor to B side of the analog channel on the NetGuardian. This example shows analog channel 1. c. Connect (+) from the A side of the NetGuardian to resistor. Solder resistor to wire. d. Use 1/8 shrink wrap to cover solder joint. Apply heat to shrink tubing. e. Connect the other side of the resistor to the Battery. Thermalogic Sensor 4 2 (-) 3 1 (+) Potentiometers
2 Using the Thermologic Temp Sensor with a NetGuardian Example: NetGuardian 216 Temperature Probe Resistor in Analog 1 - Red ( ) -Battery Black (+) GND To battery Position the sensor as shown above, with (circled) potentiometers at the bottom.
3 Using the Thermologic Temp Sensor with a NetGuardian Alternatively, a 12VDC source, or DC-DC converter can be used to provide the most accurate 12VDC. Example: NetGuardian 216 Temperature Probe -48V GND - Red ( ) Black (+) For a NetGuardian G4 or G5: Verify that the Analog channel to be used on the NetGuardian as the current Jumper installed. You can change the settings for analog alarm inputs by resetting the jumpers on NetGuardian s circuit board. To open the unit and expose the circuit board, remove the screws on the bottom and the screws on the sides of the NetGuardian. Slide the top cover off. The image above shows the circuit board and the location of the adjustable jumpers.
4 Analogs on the NetGuardian 216: Analogs on the NetGuardian 834A G4: Control Relay Jumpers
5 Access panels on the NetGuardian 834A/864A G5: By default, all the adjustable jumpers are open. for analog alarm input jumpers, the open position corresponds to voltage input, and the closed position corresponds to current input. To configure your NetGuardian to read from this sensor, use the web browser interface. Open a web browser and type in the IP address of your NetGuardian. Logon to the unit. NetGuardian 216 G3 web browser NetGuardian 832A G4 & NetGuardian 832/864A G5 web browser
6 From the green Edit menu, click on Analogs. NetGuardian 216 G3 web browser NetGuardian 832A G4 & NetGuardian 832/864A G5 web browser For a NetGuardian G4 or G5: Click on the Units link for the channel you wired the sensor to. For the NetGuardian 216 G3: You ll begin at the (Basic) Analogs screen. Enter the following scaling in the fields as shown by the screen capture. The scaling shows that when the Net Guardian reads a 1Vdc drop across the current loop resistor, the sensor is reading 20ºF, and when the NetGuardian reads a 5Vdc drop across the current loop resistor, the sensor is reading 180ºF. NetGuardian G4 / G5 web browser * * Note: The Description field must be populated to enable the channel
7 NetGuardian 216 G3 web browser ** Enter a description for this channel, as well as your threshold values. These values are based on the converted voltage. (actual temperature readings). ** Note: To enable the channel, the check box next to the Description must be checked. To verify functionality, click on the Analogs in the Monitor menu. NetGuardian 216 G3 web browser NetGuardian 832A G4 & NetGuardian 832/864A G5 web browser Here, you will see the temperature value being read by the NetGuardian, and the thresholds that have been crossed.
8 Instructions for Using the Thermologic Sensor
MARELLI SRA EDL8 ECU
MARELLI SRA EDL8 ECU INTRODUCTION AIM has developed special applications for many of the most popular ECUs; by special applications we mean user-friendly systems which allow to easily connect your ECU
More informationFactory Packaged Controls. OE (AAON Part No. V12090) MODGAS-X Controller Field Technical Guide
Factory Packaged Controls OE377-26-00058 (AAON Part No. V12090) MODGAS-X Controller Table of Contents GENERAL INFORMATION... 3 Overview...3 Features...3 INSTALLATION & WIRING... 4 Supply Air Temperature
More informationProduct Information Page
PROGRAMMING GC31 PRESSURE TRANSMITTER TO MONITOR AND CONTROL A HYDRAULIC PRESS PIP #: TR-PI-104 The GC31 differential pressure transmitter is compact, flexible and supports numerous pressure applications
More informationUniversal Gauge User Manual v1.0
Universal Gauge User Manual v1.0 For gauge hardware revision 4, software version 7 www.perfecttuning.net 1 December 2016 Table of content Table of content... 2 Warning... 4 1 Wiring... 4 1.1 Black 8 conductor
More information1 EASY COMMISSIONING GUIDE FRONIUS PV-SYSTEM CONTROLLER
1 EASY COMMISSIONING GUIDE FRONIUS PV-SYSTEM CONTROLLER Reading this document does not substitute for user s reference to CIRCUTOR CDP-DUO user-guide. 1.1 Scope Using Fronius grid-tie inverters in remote
More informationLab 4.4 Arduino Microcontroller, Resistors, and Simple Circuits
Lab 4.4 Arduino Microcontroller, Resistors, and Simple Circuits A microcontroller is a "brain" of a mechatronic system that interfaces sensors with a computer. Microcontrollers can perform math operations,
More informationINSTALLATION INSTRUCTIONS THERMOCOUPLE EXPANSION MODULE
INSTALLATION INSTRUCTIONS THERMOCOUPLE EXPANSION MODULE 2650-1846-77 Rev. B Details: Temperature Rating: -40 C to 85 C/-40 F to 185 F Vibration Specification: 20 g continuous, 50 g shock Inputs: o 4 EGT
More informationObserve all necessary safety precautions when controlling the soft starter remotely. Alert personnel that machinery may start without warning.
Introduction OPERATING INSTRUCTIONS: MCD REMOTE OPERATOR Order Codes: 175G94 (for MCD 2) 175G361 + 175G9 (for MCD 5) 175G361 (for MCD 3) 1. Introduction 1.1. Important User Information Observe all necessary
More informationG3 GEMINI INTELLIFRESH BREWER
G3 GEMINI INTELLIFRESH BREWER TROUBLESHOOTING GUIDE GEMTIF10A1000 G3 Twin 1.5 Gallon Satellite Brewer with IntelliFresh GEMSIF10A1000 G3 Single 1.5 Gallon Satellite Brewer with IntelliFresh BREWER PARTS
More informationMarelli MF4M ECU Technical documentation Release 1.01 INTRODUCTION logger Race Studio 2
MARELLI MF4M ECU INTRODUCTION AIM has developed special applications for many of the most popular ECUs; by special applications we mean user-friendly systems which allow to easily connect your ECU to our
More informationAdvanced Outdoor Airflow Control, DCV Control and Alarm Solution for OA Applications Document Name: QG_EAC1100_A_R3A
Automation, Inc. Model EAC1100 /A QUICK INSTALL GUIDE Advanced Outdoor Airflow Control, DCV Control and Alarm Solution Enhancer QUICK INSTALL GUIDE for ENHANCER Advanced Outdoor Airflow Control, DCV Control
More informationDMX-A2-DRV Integrated Advanced Step Motor Driver
DMX-A2-DRV Integrated Advanced Step Motor Driver DMX-A2-DRV Manual page 1 rev 3.10 COPYRIGHT 2008 ARCUS, ALL RIGHTS RESERVED First edition, May 2008 ARCUS TECHNOLOGY copyrights this document. You may not
More informationECONOMISER SERIES E2T USER MANUAL
TURBO S.R.L. Electronic Control Systems for Dust Collectors e-mail: info@turbocontrols.it web: www.turbocontrols.it TEL. ++39 (0)362 574024 FAX ++39 (0)362 574092 ECONOMISER SERIES E2T USER MANUAL 24/06/2014
More informationMid-West Instrument. Series 700 "Wet/Wet" Installation and Operating Instructions. Differential Pressure Transmitter
Mid-West Instrument IM_700/A Series 700 "Wet/Wet" Installation and Operating Instructions Differential Pressure Transmitter 6500 Dobry Dr. Sterling Heights, MI USA Toll Free: 800-648-5778 Ph 586-254-6500
More informationMARELLI MF4 Toyota ECU
MARELLI MF4 Toyota ECU INTRODUCTION AIM has developed special applications for many of the most popular ECUs; by special applications we mean user-friendly systems which allow to easily connect your ECU
More information2-PHASE STEPPING MOTOR DRIVER FE Z5 DISPENSE
2-PHASE STEPPING MOTOR DRIVER FE Z5 DISPENSE For Diaphragm Dosing Pumps FEM 1.02_.55 / FEM 1.09_.55 Controller board package, without pump: ID 160536 Operating and Installation Manual It is important to
More informationMAGPOWR Spyder-Plus-S1 Tension Control
MAGPOWR TENSION CONTROL MAGPOWR Spyder-Plus-S1 Tension Control Instruction Manual Figure 1 EN MI 850A351 1 A COPYRIGHT All of the information herein is the exclusive proprietary property of Maxcess International,
More informationMICRO P-711 Exerciser Instruction Book
DINOSAUR ELECTRICS MICRO P-711 Exerciser Instruction Book First Edition Table of Contents Introduction 1- MICRO P-711 tests AC DC Gas 5 Dometic eyebrow ID drawings 6 Dometic AES and AMES tests AC 7 DC
More informationDycon D2430 EN54-4 Fire Alarm Power Supply Series
Dycon D2430 EN54-4 Fire Alarm Power Supply Series Technical Description Installation and Operating Manual Construction Product Regulation 0359-CPR-00434 Page 1 of 14 Contents 1. General... 3 1.1 Product
More informationAGELKOM CAP04V-9 Plasma and Oxy Fuel Torch height control for sheet metal cutting machines Height Sensor & Controller
AGELKOM CAP04V-9 Plasma and Oxy Fuel Torch height control for sheet metal cutting machines Height Sensor & Controller 9 PIN D-SUB INTERFACE CAP 04 CAPACITIVE HEIGHT CONTROLLER IN POSITION CABLE FAULT Description:
More informationEFIE Wideband O2 (Electronic Fuel Injector Enhancer) Installation & Operating Instructions.
EFIE Wideband O2 (Electronic Fuel Injector Enhancer) Installation & Operating Instructions. The EFIE is not intended to be a fuel saver by itself. The EFIE is designed to be used in conjunction with fuel
More informationBAPI-Stat 4 Room Humidity Sensor (BA/ B4 -H200 Series)
Overview The BAPI-Stat 4 Style room unit is available as a humidity only sensor or as a combination temperature and humidity sensor with optional LCD display, temperature setpoint adjustment and occupant
More information32XR. 3 Phase Duplex Pump Control Panel (Level Transmitter Based) Quick Start Guide
32XR 3 Phase Duplex Pump Control Panel (Level Transmitter Based) Quick Start Guide RED ALARM LIGHT LEVEL CONTROLLER H-O-A SWITCHES HORN SILENCE INNER DOOR MOTOR STARTERS WITH INTERCHANGEABLE OVERLOAD MODULES
More informationUser Manual. T6 Tachometer. Online: Telephone: P.O. Box St. Petersburg, Florida 33736
User Manual T6 Tachometer Online: www.phareselectronics.com Telephone: 727-623-0894 P.O. Box 67251 St. Petersburg, Florida 33736 Table of Contents Overview... 1 Description... 1 Wiring... 1 T6 Tachometer
More informationApplication Engineering
Application Engineering February, 2009 Copeland Digital Compressor Controller Introduction The Digital Compressor Controller is the electronics interface between the Copeland Scroll Digital Compressor
More informationInstalling a Programmed Fronius SCERT in a Managed AC Coupled system
Installing a Programmed Fronius SCERT in INTRODUCTION This document is included with Fronius SCERT PV Inverters that have been programmed. It applies only to units that have been programmed and are ready
More informationGenerator Set Applications FT-10 Network Control Communications Module (CCM-G) Kit
Instruction Sheet 10 2004 Generator Set Applications FT-10 Network Control Communications Module (CCM-G) Kit 541 0810 GENERAL INFORMATION This kit contains one Control Communications Module (CCM-G) with
More informationAutomatic Transfer Switch FT-10 Network Control Communications Module (CCM-T) Kit
Instruction Sheet 10-2004 Automatic Transfer Switch FT-10 Network Control Communications Module (CCM-T) Kit 541 0811 PURPOSE OF KIT A CCM-T is used to monitor and control an automatic transfer switch.
More informationAdvanced Battery Charger. 3 - stage charging capability (IUoU) 25A
Cxx Features: Universal AC input with active PFC Compatible with Lead Acid, Li-ion, Gel and AGM batteries Support optional remote controller (CR-) Voltage / temperature compensation with battery temp.
More informationMPT SERIES OPERATING MANUAL. Caution: To Operate this controller safely, use the Safe Operating Area Design Tool Online at
LASER DIODE DRIVERS TEMPERATURE CONTROLLERS Simply Advanced Control for Your Cutting Edge Design MPT SERIES OPERATING MANUAL Caution: To Operate this controller safely, use the Safe Operating Area Design
More informationCRAGG RAILCHARGER Instruction Manual for 20SMC-12V 20SMC-24V 40SMC-12V 40SMC-24V 60SMC-12V 80SMC-12V
CRAGG RAILCHARGER for 20SMC-12V 20SMC-24V 40SMC-12V 40SMC-24V 60SMC-12V 80SMC-12V Contents 1 Warnings, Cautions, and Notes... 1 2 Description... 2 3 Features... 2 3.1 STANDARD FEATURES... 2 3.2 OPTIONAL
More informationIDEAL INDUSTRIES INC. TECHNICAL MANUAL - SUPPLEMENT MODEL
IDEAL INDUSTRIES INC. TECHNICAL MANUAL - SUPPLEMENT MODEL 61-791 The Service Information provides the following: This is a Supplemental Manual to Megger s DM220 Service Manual and is intended for Performance
More informationRand McNally Device Software. What s New (Version )
Rand McNally Device Software What s New (Version 5.40.03) HOS* 34 Hour Reset Change Reverts back pre-july 2013 rules. Drivers no longer need two consecutive periods of off-duty time between 1AM-5AM. Drivers
More informationLINEAR ACTUATOR INDUSTRIAL DUTY 10A/B SERIES
Product Data Sheet Standard Features: All steel frame and extension tube o Aluminum gearbox housing o Ball screw version has stainless steel extension tube Nominal stroke lengths: 4 [102mm], 6 [153mm],
More informationGE Sensing & Inspection Technologies
GE Sensing & Inspection Technologies Modus Model RPM-1 Room Pressure Monitor Installation and Setup Guide 1. GENERAL The RPM-1 monitors either positive or negative room pressures (see the Datasheet for
More informationLINEAR ACTUATOR INDUSTRIAL DUTY LACT BALL SCREW DRIVE
Product Data Sheet LINEAR ACTUATOR Standard Features: All steel frame with stainless steel extension tube o Aluminum gearbox housing Nominal stroke lengths: 4 [102mm], 6 [152mm], 8 [203mm], 12 [305mm],
More informationDC Variable Speed Drive Panel
DC Variable Speed Drive Panel Installation, Operation & Maintenance Instruction Manual Bulletin #: CC-IOM-0103-D Manufacturers of Quality Pumps, Controls and Systems ENGINEERED PUMP OPERATIONS 2883 Brighton
More informationG3 LOW PROFILE AIRPOT BREWER
G3 LOW PROFILE AIRPOT BREWER TROUBLESHOOTING GUIDE TLP BREWER PARTS IDENTIFICATION PART # DESCRIPTION 1. WC-2962-101K KIT, FITTING SPRAYHEAD KYNAR 2. WC-717 CONTROL BOARD, SMART CARD SWITCH PANEL 3. WC-29030
More informationSystem Connection Box. Engine Connection Box. Engine. Legend. VP Wiring. VP Supply. Yard Wiring SEM C. File Name: SEM C
Modbus on RS To yard System Connection Box Marine Control Unit MCU Potential free relay contacts X... X6 Signals from VP system to yard IDCOM Shut Down Unit SDU Terminal Block X9 Signals to VP system from
More informationT21 Thermal Differential Switch
T21 Thermal Differential Switch General Instructions The T21 Point Level Switch is a state-of-the-art in liquid level and interface measurement and control. Level detection is accomplished by using a high-resolution
More informationGenerator Sets Controller 210. Operation Manual. Ver1.0
Generator Sets Controller 210 Operation Manual Ver1.0 Note This information could include technical inaccuracies or typographical error. Manufacturer may make improvements and/or changes in the product(s)
More informationLINEAR ACTUATOR INDUSTRIAL DUTY LACT ACME DRIVE SERIES
Product Data Sheet LINEAR ACTUATOR Standard Features: All steel frame and extension tube o Aluminum gearbox housing Nominal stroke lengths: 4 [102mm], 6 [152mm], 8 [203mm], 12 [305mm], 18 [457mm], 24 [610mm],
More informationPKS-FD Servo System
PKS-FD123-01 Servo System FEATURES 24-70VDC of 0.32 Nm Power Ratings up to 100 Watts 2,500 PPR Incremental Encoder Maximum Speed of 6500 RPM IP65 for Body, IP54 Shaft Seal Brake Option Available Position,
More informationInlet Controller TC5-ITA USER'S MANUAL. M rev. 02 K rev. 00
Inlet Controller TC5-ITA USER'S MANUAL M 890-00047 rev. 02 K 895-00458 rev. 00 TABLE OF CONTENTS PRECAUTIONS... 3 FEATURES... 4 LOCATION OF THE CONTROLS... 5 Status Leds...5 Internal Switches...6 INSTALLATION
More informationCircuit breaker wear monitoring function block description for railway application
Circuit breaker wear monitoring function block description for railway application Document ID: PP-13-21313 Budapest, September 2016 CONTENTS Circuit breaker wear monitoring function...3 Technical data...5
More informationC.E. Niehoff & Co. C505, C527, C531, and C534 Alternators Troubleshooting Guide CAUTION. Testing Guidelines. Hazard Definitions WARNING
C.E. Niehoff & Co. C505, C527, C531, and C534 Alternators Troubleshooting Guide WARNING Before troubleshooting any CEN products, the service technician should: read, understand, and agree to follow all
More informationLow voltage AC drives
General machinery drives Main features and dimensions Unique features Fast and extensive I/O PID control Application macros Many installation possibilities 200 to 480 V, 1-phase or 3-phase More value for
More informationAdding an LED indicator to the X10-WS467 wall switch Credit: Bruce Stydnicki
1 of 6 1/2/2009 4:33 PM Adding an LED indicator to the X10-WS467 wall switch Credit: Bruce Stydnicki 1. I had a need to monitor the status of my outdoor lights which are connected to X10-WS467 wall switches.
More informationLINEAR ACTUATOR INDUSTRIAL DUTY 10A SERIES
Product Data Sheet LINEAR ACTUATOR Standard Features: All steel frame and extension tube o Aluminum gearbox housing Nominal stroke lengths: 4 [102mm], 6 [153mm], 8 [203mm], 12 [305mm], 18 [457mm], 24 [610mm],
More informationTRAC-3 TENSION READOUT AND CONTROL
Magnetic Power Systems, Inc. 1626 Manufacturers Drive. Fenton, MO 63026 Tel: 636.343.5550 Fax: 636.326.0608 magpowr@magpowr.com INSTRUCTION MANUAL TRAC-3 READOUT AND CONTROL For Control of Magnetic Particle
More informationKNC-PKS-FD S-AAK-DKH
KNC-PKS-FD123-02 - Servo System FEATURES 24-70VDC of 90 oz-in Power Ratings up to 200 Watts 2,500 PPR Incremental Encoder Maximum Speed of 6000 RPM IP65 for Body, IP54 Shaft Seal Brake Option Available
More informationAdvanced Battery Charger 0 ~ 15A 0 ~ 25A 0 ~ 35A 0 ~ 50A 0 ~ 80A. 3 - stage charging capability (IUOU) 90 ~ 264VAC (refer to de-rating curve)
Cxx Features: Universal AC input with active PFC Compatible with Lead Acid, Li-ion, Gel and AGM batteries Support optional remote controller (CR-) Voltage / temperature compensation with battery temp.
More informationLow Voltage Disconnect, Sure Power 54.18
Low Voltage Disconnect, Sure Power 54.18 Functional Test NOTE: If the LVD deactivates (removes power to the cab/sleeper loads), it needs to be reset prior to performing a functional test. If the batteries
More informationHGM1780. Automatic Genset Controller USER MANUAL. Smartgen Technology
HGM1780 Automatic Genset Controller USER MANUAL Smartgen Technology Smartgen Technology Co., Ltd No. 28 Jinsuo Road Zhengzhou Henan Province P. R. China Tel: 0086-371-67988888/67981888 0086-371-67991553/67992951
More informationLINEAR ACTUATOR INDUSTRIAL DUTY LACT SERIES
Product Data Sheet Standard Features: All steel frame and extension tube o Aluminum gearbox housing o Ball screw version has stainless steel extension tube Nominal stroke lengths: 4 [102mm], 6 [152mm],
More informationUSERS MANUAL MCD REMOTE OPERATOR
USERS MANUAL MCD REMOTE OPERATOR Order Code: 175G9004, 175G3061 Contents Contents Introduction...2 Important User Information...2 General Description...2 Symbols Used in this Manual...2 Installation...3
More informationIBM CMM Quick Reference Guide
IBM CMM Quick Reference Guide Contents Introduction Prerequisites Requirements Components Used CMM Overview CMM Layout Useful CMM Screens Login Screen System Information Screen Event Log Screen Chassis
More informationPAGE Both power cords must be connected & powered to operate the E-TES 120.
PAGE 1 This document outlines questions to ask and components to check during E-TES 120 troubleshooting. More detailed troubleshooting procedures are available in the E-TES 120 Troubleshooting Guide. 1.
More informationCarbon Monoxide Transmitter
Introduction The CO Transmitter uses an electrochemical sensor to monitor the CO level and outputs a 4-20 ma signal. The standard product features a 2- wire loop-powered output. Optionally, the device
More informationExplanation 1 Input External Switch 2 Input Hipot Safety Switch
on the 1100H+ The 1100H+ has capability, which allows you to set up the tester to control external devices with tester functions. You can also use an input on the tester to start a test. For example, the
More informationSonoSelect and SonoSafe energy meters
energy meters 01/2016 Danfoss VUIGB202 1 2 Danfoss Energy Meters 2016.01 VUIGB202 Contents 1. Inside the box... 4 2. Installation..............................................................................
More informationOctave Water Meter Installation Manual
Octave Water Meter Installation Manual 1.0 Notes For proper flow measurements, the OCTAVE s measuring tube should be completely full at all times. Non-wetted sensors show loss of signal. Though this will
More informationVersion 1.0 Copyright DC-RPM-iBox User Manual
Version 1.0 Copyright 2012 DC-RPM-iBox User Manual D Y N O C O M S E R I E S C H A S S I S D Y N A M O M E T E R S DC-RPM-iBox User Manual Copyright This manual is copyrighted by Dynocom Industries, Inc.,
More informationNPD to FID conversion on SRI 8610C or 310C GC July2012
July2012 Unplug GC from wall power The SRI 8610C GC is shown at right. The NPD detector will be located at the right side of the column oven covered with an insulated aluminum box. Remove the single screw
More informationMagnet. Status Report. Pablo Campero Detector Support Group
Magnet Status Report Pablo Campero Detector Support Group DSG STAFF 2 Overview Solenoid Torus Contents Control, Monitoring, and Interlock Systems Cryogenics Distribution Box Solenoid Torus Tasks Torus
More informationNeuron THS. User Manual Driver App. User Manual Driver App Rev 1.0
Neuron THS User Manual Driver App Introduction The THS App is a Web App supporting all devices. To access the app, go to https://neuronths.com/ in your web browser. Scan QR code below to access the web
More informationCommander IS0128 ISO128E ECR# /04. Tachometer/ Engine Hourmeter
Commander Tachometer/ Engine Hourmeter Analog Tachometer Digitally displays Hours Engine Has Been Run Fuel Level Other Features if Available: Fuel anagement Fuel Flow in GPH or LPH Total or Trip Fuel Used
More informationNetSure 5100 ORDERING GUIDE. 48V & 24V DC Power System (40 A to 600 A)
NetSure 5100 ORDERING GUIDE 48V & 24V DC Power System (40 A to 600 A) NETSURE 5100 ORDERING GUIDE Description The NetSure 5100 Series, a compact -48 volt 600 A DC power solution, features an advanced control
More informationHGM6320T AUTOMATIC GENERATOR CONTROLLER USER MANUAL
HGM6320T AUTOMATIC GENERATOR CONTROLLER USER MANUAL Smartgen Technology Smartgen Technology Co., Ltd No. 28 Jinsuo Road Zhengzhou Henan Province P. R. China Tel: 0086-371-67988888/67981888 0086-371-67991553/67992951/67992952
More informationQUICK INSTALLATION GUIDE
MANUAL/AUTOMATIC T R A N S M I S S I O N 2 - B U T T O N R E M O T E S T A R T E R W I T H V I R T U A L T A C H S Y S T E M ( A S P R G - 1 0 0 0 C O M P A T I B L E ) QUICK INSTALLATION GUIDE Manual
More informationTELEDYNE. PB 4213 June JUDSON TECHNOLOGIES A Teledyne Technologies Company TELEDYNE JUDSON TECHNOLOGIES TC8 TEMPERATURE CONTROLLERS
TC8 TEMPERATURE CONTROLLERS Operating Instructions PB 4213 June 2004 The TC8 is a self contained Thermoelectric Cooler Temperature Controller for single and multistage TEC cooled photodetectors housed
More informationInstallation Instructions for VTU
Installation Instructions for VTU 1 Introduction This installation manual covers the installation of the Vehicle Tracking Unit (VTU). This manual is for the professional and novice installer and should
More informationM u l t i P o w e r. CM MultiPower. Installation and Operating Manual
M u l t i P o w e r CM MultiPower Installation and Operating Manual Index 1. Introduction of the 4HS submersible pumps range... 3 2. Safety Instructions... 4 3. CM MP installation... 5 3.1 Electric wiring...
More informationPropane and Gasoline Electronic Fuel Injection
Zenith Electronic Engine Management System Propane and Gasoline Electronic Fuel Injection 1 Slide 1 2 Slide 2 Home Page System Advantages Block Diagram, Electronic Control Unit Inputs Output Controls System
More informationABB Component Drives ACS150, 0.5 to 5 Hp
ABB Component Drives ACS150, 0.5 to 5 Hp Technical Catalog BUSINESS PROFILE INDUSTRIES PRODUCTS APPLICATIONS EXPERTISE PARTNERS SERVICES Contents Choice 1: Simply contact your local ABB drives sales office
More informationwith lcd display 12-42v
instructions for: AUTO PROBE with lcd display 12-42v MODEL No: PP7 Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
More informationAC drive has detected too high a Check loading
Fault code Fault Name Fault type Default Possible Cause Remedy 1 Over Current Fault AC drive has detected too high a Check loading current (>4*IH) in the motor cable: Check motor Sudden heavy load increase
More informationAdvanced Battery Charger. 3 - stage charging capability (IUOU) 4.1 A / 100VAC 1.8A / 240VAC
Cxx Features: Universal AC input with active PFC Compatible with Lead Acid, Li-ion, Gel and AGM batteries Support optional remote controller (CR-) Voltage / temperature compensation with battery temp.
More information16-Channel Digital Output Termination Card Introduced Power 24Vdc
TDO16AIN 16-Channel Digital Output Termination Card Introduced Power 24Vdc (TDO16AIN) Issue 6 October 2005 INTRODUCTION PURPOSE The TDO16AIN 16-channel digital output termination card acts as an interface
More informationA3Z OPERATING MANUAL
A3Z OPERATING MANUAL TABLE OF CONTENTS Introduction... p. 2 Features... p. 2 Description... p. 3 Theory of Operation... p. 3 Installation... p. 4 Electrical Connections... p. 5 Options... p. 6 Warranty...
More informationSB 2000 PUSH TO SEARCH NEXT STAG E. Aerotech, Inc. FORM: QM 1320
Inlet Controller SB 2000 USER'S MANUAL AUTO OPEN MANUAL PUSH TO SEARCH NEXT STAG E CLOSE Aerotech, Inc. FORM: QM 1320 4215 Legion Dr. Mason, MI 48854-1036 USA Rev. 3, Sept. 1997 Ph. (517) 676-7070 Fax
More informationSOLAR SMART. 12/24V 20Amp MPPT Solar Charge controller with Ethernet
SOLAR SMART 12/24V 20Amp MPPT Solar Charge controller with Ethernet Embedded web pages, SNMP support, output port for external Relay board and GSM SMS unit port USER MANUAL PLEASE READ THIS MANUAL CAREFULLY
More informationNotice Regarding this Upgrade. WARNING! Danger Potential
Notice Regarding this Upgrade WARNING! Danger Potential Although this kit has been designed to be easy-to-install, and has been tested in many installations; caution must be exercised when installing this
More informationSP PRO ABB Managed AC Coupling
SP PRO ABB Managed AC Coupling Introduction The SP PRO ABB Managed AC Coupling provides a method of linking the ABB PVI-3.0/3.6/4.2- TL-OUTD and ABB PVI-5000/6000-TL-OUTD string inverters to the SP PRO
More informationSoiling Measurement Kit
Soiling Measurement Kit NRG SRA System Kit #11174 Authors: Technical Services TABLE OF CONTENTS INTRODUCTION 3 MATERIALS & TOOLS 4 Inside the Kit... 4 Required Tools... 4 SECTION 1: ASSEMBLING THE SOILING
More informationOptional: Wiring a Relay for Gauge Controlled Output
Wiring Installation Instructions for : PYROMETER 2 1/16 Spek Pro Professional Racing Gauge GAUGE 12-Pin Wiring Harness & Plug Firewall Grommet DIAGRAM 1 Black-Engine Ground 12-Pin Wiring Harness CUP Coil
More informationASSEMBLY INSTRUCTIONS ZONE MODULE 2 1 THERMOSTAT DESCRIPTION POWER SUPPLY AIRZONE CONTROLLER
ZONE MODULE 2 1 ASSEMBLY INSTRUCTIONS AIRZONE CONTROLLER THERMOSTAT DESCRIPTION The Touch Thermostat, is the access panel for the installer to configure the Zone Module, and also, for the user to change
More information1100 Series Piston Type Differential Pressure Gauges
1100 Series Piston Type Differential Pressure Gauges 1. Safety Before installing, check the Series Number and verify compatibility to the process media and temperature in contact with the wetted parts.
More informationFisher FIELDVUE DLC3010 Digital Level
Quick Start Guide DLC3010 Digital Level Controller Fisher FIELDVUE DLC3010 Digital Level Controller Contents Installation... 2 Mounting... 8 Electrical Connections... 13 Initial Setup... 18 Calibration...
More informationSMARTLINK METER. Digital Self-checking Thermal Mass Flow Meter
Flow Control Components - SMARTLINK METER 10-30.9-1 SMARTLINK METER Digital Self-checking Thermal Mass Flow Meter Precise, repeatable mass flow measurement for fuel, air and combustion streams Displays
More informationITCEMS950 Idle Timer Controller - Engine Monitor Shutdown Isuzu NPR 6.0L Gasoline Engine
Introduction An ISO 9001:2008 Registered Company ITCEMS950 Idle Timer Controller - Engine Monitor Shutdown 2014-2016 Isuzu NPR 6.0L Gasoline Engine Contact InterMotive for additional vehicle applications
More informationINSTALLATION & OPERATING MANUAL RW SERIES WALL-MOUNT RECTIFIERS
INSTALLATION & OPERATING MANUAL RW SERIES WALL-MOUNT RECTIFIERS WWW.UNIPOWERTELECOM.COM Manual No. RW-1 2008 UNIPOWER Corp. 01/24/08 rw-man All Rights Reserved UNIPOWER Telecom, Division of UNIPOWER Corporation
More informationLingenfelter NCC-002 Nitrous Control Center Quick Setup Guide
Introduction: Lingenfelter NCC-002 Nitrous Control Center Quick Setup Guide The NCC-002 is capable of controlling two stages of progressive nitrous and fuel. If the NCC-002 is configured only for nitrous,
More informationApplication Engineering
Application Engineering March 2011 Copeland Digital Compressor Controller Introduction The Digital Compressor Controller is the electronics interface between the Copeland Scroll Digital compressor or the
More informationEZ-TRAC Digital Tension Readout and Control
Magnetic Power Systems, Inc. 1626 Manufacturers Drive. Fenton, MO 63026 Tel: 636.343.5550 Fax: 636.326.0608 magpowr@magpowr.com INSTRUCTION MANUAL EZ-TRAC Digital Tension Readout and Control Table of Contents
More informationPowerCommand iwatch Wireless
PowerCommand iwatch Wireless Description The PowerCommand iwatch Wireless remote monitoring system provides a simple, inexpensive method for remotely monitoring gensets. The monitor communicates with a
More informationGUARDIAN 401 A - Symptom Flow Chart - Lift Interlock Condition Possible Causes Action No prove out of LED's
GUARDIAN 401 A - Symptom Flow Chart - Lift Interlock Condition Possible Causes Action prove out of LED's Connections Power Ground Wake up LED panel Harness(es) Module Go to Pinpoint Test A LED's not illuminated
More informationSecurity alarms, warning systems.
SIREN DRIVER BOARD. Free running siren activated by the application of a V DC power source. This module is capable of driving a maximum of 2 x 8 ohm 10W speakers and produces approximately 110 db at one
More information6K-SSR-RACK08 Specifications
Specifications Document Revision 1.1, February, 2010 Copyright 2010, Measurement Computing Corporation Typical for 25 C unless otherwise specified. Specifications in italic text are guaranteed by design.
More informationQuick Start Guide of CV50- ControlVIT Series
❶ Safety precautions Do not refit the inverter unauthorizedly; otherwise fire, electric shock or other injury may occur. Please install the inverter on fire-retardant material and keep the inverter away
More information