Crawford 542 Overhead sectional door. Product datasheet

Transcription

1

2 Copyright and Disclaimer Notice Although the contents of this publication have been compiled with the greatest possible care, cannot accept liability for any damage that might arise from errors or omissions in this publication. We reserve the right to make appropriate technical modifications/replacements without prior notice. No rights can be derived from the contents of this document. Colour guides: Colour differences may occur due to different printing methods., Megadoor, hafa, EconoRoll, MobiGuard and MobiOpener are registered trademarks owned by The Cardo Group Copyright No part of this publication may be copied or published by means of printing, photocopying, microfilm or any other process whatsoever without prior permission in writing by. All rights reserved

3 Technical facts Features Max size: (W x H)* 8000 x 6000 mm Panel thickness: 42 mm Panel material: Microrilled steel or aluminium Filling: CFC-free polyurethane Weight: Steel: 13 kg/m2 Alu: 10 kg/m2 Colour outside: 8 Standard RAL colours Colour inside: RAL 9002 Track types: Standard: SL Optional: HL, LL, VL, VLL Windows: Optional: DARP, DAOP, DSR Passdoor: Optional: In door leaf or in side section Electrical operation: Optional: Automated operation, Access control, Safety functions * Other sizes are available on request Performance Life time expectations: Door: door cycles/10 years Springs: door cycles Wind load, Class 3 ( 4250 mm DLW) EN12424* Class 2 (> 4250 mm DLW) Thermal transmittance, 1,0 W/(m 2.k) Steel door EN ,1 W/(m 2.k) Alu door 1,25 W/(m 2.k) With windows/passdoor Water penetration, Class 3 (4000 x 4000 mm) EN12425 Air permeability, Class 2 (4000 x 4000 mm + passdoor) EN12426 * Higher wind load classification on request iii

4 Contents Copyright and Disclaimer Notice...ii Technical facts...iii Features... iii Performance... iii 1. Description General Standard Options Door leaf Construction Material Colours Seals Handle Locks Windows Wind reinforcement truss Fixed sections Passdoor Track sets General Standard lift High lift Low lift Vertical lift Vertical lift logistic Special track sets Balancing system Safety devices Operating system Types of operation CDM9 Operator Door control systems CDM5 Operator series Door control system Access and automation Specifications Dimensions Daylight width and daylight height Section sizes Vertical cross-section Windows and passdoor Number of windows Windows Passdoor Door operation Selection guidelines for operation type Selection guidelines for Door operator Door control systems - Selection guidelines Door control systems - Selection guidelines for automation Door control systems - Selection guidelines Door control systems - Selection guidelines for automation...26 iv

5 3. CEN Performance Lifetime expectation Resistance to windload Resistance to water penetration Air permeability Thermal transmittance Operating forces and safe openings Building and space requirements Building preparations Installation preparations Electrical preparations Space requirements Space requirements SL Space requirements HL Space requirements LL Space requirements VL Space requirements VLL Space requirements Door operators Service...36 These keys open doors to better business Index...37 v

6 1. Description 1.1 General The 542 overhead sectional door is one of the most stable and well-insulated overhead doors on the market. It is an overhead sectional door, suitable for all types of buildings, with regard to both function and appearance. High flexibility makes it possible to install this door in almost every type of building. The door slides up under the roof when opened, allowing free space around the door opening and leaving the door opening completely free. The door is made of insulated panels that provide minimal thermal transmittance, which reduces energy cost. The 542 overhead sectional door has been designed to meet all operational and safety requirements in the European Directives and the standards issued by the European Standardization Committee, CEN Standard Although every door is custom built, the 542 overhead sectional door is supplied with the following specifications as standard: Door leaf: Locks: Colours: Track type: Operation: Safety: Options Insulated steel or aluminium panel Lock bolt with lock hole protection 8 RAL colours, pre-coated SL: Standard Lift Pull down rope and step/lifting handle SBD: Spring Break Device provides a wide range of options and accessories to customise the 542 overhead sectional door to any customer s needs. Fixed sections: Passdoor: Panel windows: Framed section: Locks: Colours: Track types: Operation: Safety: Top and side sections In door leaf or in side section DARP: Double glazed Acrylic Rectangular Pane DAOP: Double glazed Acrylic Oval Pane DSR: Docking window Single Row 242 door section Cylinder lock Foot lock Panic lock (on pass door) Factory painting HL: High Lift LL: Low Lift VL: Vertical Lift VLL: Vertical Lift Logistic D hoist T hoist U hoist CDM9 Operator CDM5 Operator CBD: Cable Break Device The 542 overhead sectional door has 4 primary parts: 1. Door leaf 2. Track set 3. Balancing system 4. Operating system/chainhoist (optional) 6 Description

7 1.2 Door leaf Construction The 542 overhead sectional door leaf has horizontal sections, connected together with hinges. The outer hinges of each section have rollers that run in the tracks. The horizontal sections are insulated panels, filled with CFC-free polyurethane Colours The RAL-colours are as close as possible to the official RAL HR collection. Max. deviation is 1,0 ΔE Standard pre-coated range: RAL 1021 RAL 3002 RAL 5010 RAL 6005 RAL 7016 RAL 9002 RAL 9006 RAL Standard colours Steel Material The surface of the door leaf panels is characterized by the microrilled steel or aluminium sheet. Outside colour: The steel panel is available in the 8 standard colours above. Inside colour: RAL Grey white. Aluminium Outside colour: The aluminium panel is available in 2 standard colours: RAL Gentian blue, RAL Pure white. Inside colour: Clear polyester. 1. Polyester coating 2. Primer 3. Chromate layer 4. Zinc and Aluminium coating* 5. Steel or Aluminium sheet 6. Zinc and Aluminium coating* 7. Chromate layer 8. Primer 9. CFC-free polyurethane 10. Reinforcement strips *Steel door leaf only. The aluminium door leaf is not coated Optional colours Factory painting Factory painting panel, all RAL colours, including metallic colours, outside only Factory painting panel, acc. to colour sample, outside only Miscellaneous Special effect colours (e.g. fluorescent) such as RAL 1026, 2005, 2007, 3024 and Description 7

8 1.2.4 Seals To make sure the door provides a windproof barrier, the door is equipped with top, bottom and side seals Top seal Bottom seal Installed on the bottom edge of the bottom panel, to act as a barrier as well as a shock absorber. The flexible rubber material and the O-shape provides continuous pressure on the floor, ensuring maximum sealing. Installed on the top panel, to seal the gap between the panel and the wall. The flexible rubber material provides continuous pressure on the top wall, ensuring maximum sealing Handle Side seal Installed on the track set to close the gap between the tracks and the door leaf. The flexible rubber material provides continuous pressure on the door leaf, while dodging irregularities, ensuring maximum sealing. For manual operation, every 542 overhead sectional door is provided with a solid, easy to grip and step on handle, finished with the logo. 8 Description

9 1.2.6 Locks Lock bolt A standard 542 overhead sectional door is equipped with a Lock bolt. The Lock bolt locks the door from the inside, without the use of a key. The Lock bolt is not visible from the outside Cylinder lock The Cylinder lock is a key operated lock which offers extra security. The lock is installed on the inside and can be unlocked with a key and turning the handle. Access to the Cylinder lock is possible from either only the inside, or both the inside and the outside Foot lock The Foot lock makes it possible to lock the door by applying pressure on the lever. For safety reasons, the Foot lock is only available for manually operated doors. Additional side space requirements: 60 mm Panic lock For passdoors only. The Panic lock can be locked with a key from the inside and outside, but the handle or panic bar on the inside always remains effective for opening the passdoor from the inside. Description 9

10 1.2.7 Windows The door sections can be glazed with windows*. The number of windows per section is directly related to the daylight width. Optionally, one single window can be placed on the outer left or right side, in the third section. *The bottom section cannot be glazed DARP Double Acrylic (3 + 2 mm) Rectangular, in Plastic frame Light opening: 604 x 292 mm Window frame: black polycarbonate Window frames are burglar proof Frame section The 542 overhead sectional door can be fitted with a 242 frame section. The height of this section is 600mm. Please refer to 242 documentation for details DAOP DAOP: Double Acrylic (2 + 2 mm) Oval, in Plastic frame Light opening: 610 x 292 mm Window frame: black polycarbonate Window frames are burglar proof Wind reinforcement truss Wider door panels and panels with windows or a passdoor are reinforced with metal profiles that act as trusses. These trusses reduce bending of the panel caused by wind loads or when the door leaf is in the horizontal position and is bending under its own weight DSR DSR: Dock Single (2+2 mm) Rectangular Light opening : 570 x 135 mm Window frame: black polycarbonate Window frames are burglar proof 10 Description

11 1.2.9 Fixed sections Fixed sections can advantageously fill space around new doors that are smaller than the wall opening. Fixed sections are available in top and side sections. Fixed sections are supplied in the same colour and construction as the door leaf. A fixed section can be provided with a passdoor for two reasons: Safety and energy cost reduction. Safety: Putting a separate passdoor in a fixed section next to the industrial door separates pedestrian and vehicle traffic. Energy cost reduction: The opening space for frequent pedestrian traffic is minimized Passdoor The passdoor is designed with a push/pull grip which ensures an easy and simple opening and closing of the passdoor. The passdoor is not designed to be an emergency exit, as it has a threshold. The passdoor can be put in either the door leaf or a side section. Features: Always opening outwards, min. 90 degrees opening Hinged left or right Seals in passdoor frame reduce air permeability. Integrated passdoor switch if electrically operated Ring shaped door handle All commonly used cylinder locks are available: Euro, Kaba, Abloy, Assa. Standard : Euro cylinder lock Door closer type M.A.B. Panic lock NEMEF/CISA (option). Description 11

12 1.3 Track sets General The track set supports the door leaf on its rollers and guides it upwards. The selection of the appropriate track set is based on various factors: Available head room Door height Type of vehicles Presence of roof obstructions, pipes and overhead crane beams. The track sets below cover most applications. Other applications are available on request Standard lift Building type: Most standard industrial buildings. Benefits: Optimal design for common buildings. The Standard Lift track set, with the spring package just above the door, is the most common solution High lift Building type: High ceilings. On the High Lift track set the spring package is placed high above the door. Benefits: This track type allows high vehicles to cross along the door opening without obstructions of the horizontal tracks. This track type is used when the space above the door is considerable, and is needed for work and traffic, e.g.: high vehicles. 12 Description

13 1.3.4 Low lift Building type: Low ceilings. Benefits: Achieve maximum daylight height with minimum head room Same as standard lift, but with the spring package at the end of the horizontal tracks. The space between the door opening and the roof does not need to be more than 265 mm. For doors with a weight > 250 kg and/or doors with pass door, the required head room is 300 mm Vertical lift Building type: Very high ceiling and high working space requirements. Benefits: Allows high vehicles to cross along the door opening without any obstructions. If the space between the daylight height and the roof is sufficient, with this track type, the door can be opened vertically Vertical lift logistic Building type: Docking bays with very high ceiling and high working space requirements. Benefits: This track type is similar to the vertical lift, but with limited measurements, especially developed for logistic docking solutions. If the space between the daylight height and the roof is sufficient, with this track type the door can be opened vertically. Description 13

14 1.3.7 Special track sets The 542 overhead sectional door track set can be custom designed to make the door fit in places that seem quite impossible. Our door technicians can solve installation problems where the door must share space with ventilation systems, crane beams, etc. A few examples: 14 Description

15 1.4 Balancing system The balancing system balances the door by applying a force nearly equal to the weight of the door leaf. This allows the door leaf to be moved up and down manually, and to stay open in any position. The system is installed on the top or the end of the track set and works as follows: Two torsion springs are installed on a shaft above the door opening. This shaft has a cable drum on each end from which door cables run to the bottom corners of the door leaf. Turning the shaft lifts the door up or down Spring break device (SBD) The Spring Break Device (SBD) is delivered with all 542 overhead sectional doors. In the event of a spring break, the sudden drop force activates the Spring Break Device (SBD). The shaft will be locked in less than 300mm of door movement Safety devices The balancing system supports heavy forces. In case of a spring or cable break, its counterforce is lost. The door is therefore equipped with two safety devices that can block downward door movement: Spring Break Device (standard) Cable Break Device (if technically required) Cable break device (CBD) The Cable Break Device (CBD) is an optional safety device. In the event of a cable break or a spring break, the cable looses its tension. The activated Cable Break Device clamps onto the track in less than 300mm of door movement. Description 15

16 1.5 Operating system Types of operation All 542 overhead sectional doors can be opened and closed by hand. They are also prepared for electrical operation. Electrically operated doors can be controlled by hand or be fully automatic. Traffic frequency, climate requirements and the weight of the door play a key role in choosing the optimal control system Pull-down rope T-hoist The 542 overhead sectional door can be operated manually with a pull-down rope. The pull-down rope is directly connected to the door leaf. U-hoist Electrical operation Chain hoist For heavier doors, a chain hoist allows easier door operation. The 542 overhead sectional door can be supplied or upgraded with an electrical operating system. Electrical operation gives access to the full program of Access and Automation functions, that can fulfill many operational needs, related to traffic type and frequency, door weight and temperature control. There are three types of chain hoist: D-hoist: Non-geared chain transmission directly connected to the shaft. Recommended for doors up to 250 kg. For hexagonal shaft only. T-hoist: Geared (ratio 1:4) chain transmission indirectly connected to the shaft. Recommended for doors up to 250 kg. For all shaft types. U-hoist: Geared (ratio 1:3) chain transmission connected to another chain between the chain hoist and the shaft. Recommended for doors of 250 kg and above. For all shaft types. 16 Description

17 1.5.2 CDM9 Operator Door control systems The CDM9 operator is a combination of the CDM9 operator and a 900-series Door control system. This system is available for doors up to 400 kg CDM9 Operator One main part of the system is the operator: an electric motor which drives the balancing shaft with the cable drums and torsion springs. It can be retrofitted to an already installed door. The CDM9 operator is mounted directly on the balancing shaft and does not require any special wall reinforcement. Key features: Smooth and silent Soft start and stop Fits all track types and shafts Life time: door cycles (depending on weight and temp.) e.g.: temp. 0 C C/weight 250 kg = cycles temp. -20 C C/weight 400 kg = cycles Description 17

18 Door control systems General The 900 Door control system series provides a range of control units, from basic up, stop and down buttons to advanced automated control. The design of all control units is based on modules, and it is possible to upgrade or downgrade safety or automation functions. Additional kits such as magnetic loop, photocells, radar, radio and reduced door opening are available. 940A Door control system The 940A Door control system is the most advanced control unit that is prepared for one or more physical upgrades from the entire range of automation systems. An automation system allows door operation by sensors or remote control. This control unit contains a 3-digit diagnostics display that allows efficient troubleshooting and displays the number of door cycles. Together with the service indicator, this extra feature allows advanced maintenance planning to users where the door is an essential element of internal logistics. 920 Door control system The 920 Door control system is the basic control unit that has the necessary hold-to-run or impulse open, hold-to-run close and stop functions and a slot for an external control box. This control unit is the economical solution for working environments where the door opening frequency is low. 930 Door control system The 930 Door control system is a basic control unit that has impulse up and down functions with supervised safety edge. An extra set of upgrade features, such as external control, that can be installed during or after installation, is available. This control unit is the more advanced solution for door openings that are frequently used by pedestrians and forklift trucks, because of its automated opening and closing function. 18 Description

19 1.5.3 CDM5 Operator series Door control system CDM5 Operator The CDM5 Operator is used on doors up to 650 kg or in application of heavy use. The operator drives the shaft via a chain transmission and is mounted on a solid surface or a steel plate. The CDM5 opens at cm/sec. 420 Door control system Impulse UP and hold-to-run DOWN. This control unit can be configured to open the door on impulse. The DOWN-button is always hold-to-run. Also a CDM5 HD is available for doors up to 1150 kg and opens at 19 cm/sec. 430 Door control system Impulse UP and DOWN. When using this door control system, the door is equipped with a safety edge, which reverses the closing door when obstructed. Three button operation as a standard. The most common automation B1 - B5 kits as an option. Also available: 430S-2H Door control system, the control unit for the two-speed CDM6-2H Operator Door control systems General The 400 Door control system series provides a range of control units, from basic up, stop and down buttons to advanced automated control. The design of all control units is based on modules, and it is possible to upgrade or downgrade safety or automation functions. Additional kits such as magnetic loop, photocells, radar, radio and reduced door opening are available. 410 Door control system 430P Door control system Impulse UP and DOWN. When using this door control system, the door is equipped with a safety edge, which reverses the closing door when obstructed. Processor operated control unit. Three button operation as a standard. All of the automation C-kits can be applied. The very basic version with hold-to-run UP and DOWN. This control unit is the economical solution for working environments where the door opening frequency is low. Description 19

20 1.5.4 Access and automation offers a wide range of functions that allows advanced opening and safety control. Please refer to the specification sheet of the control units to see which functions apply to which control unit in the 900- or 400-series Door control systems. Remote control A hand-held radio transmitter allows door operation from a vehicle or any position within meters from the receiver and aerial at the door. Receiver installed in control unit, antenna installed on the wall beside the door Basic control functions Interlocking Developed for climate control or safety; If door A is open, door B cannot be opened. If door B is open, door A cannot be opened. An interlocked door can remember an up-command, if selected via a micro switch. Circuit card Installed in control unit Automatic control functions Magnetic loop A sensor in the floor detects a metal object (usually forklift trucks, pallet trucks) and opens the door automatically. This is an ideal solution for frequent vehicle traffic. Installed on the outside, inside or both sides of the door in the floor. Reduced opening External control functions When it is unnecessary or undesirable to fully open a door, an additional switch can be used to open the door to a preprogrammed reduced opening position. Pre-fitted micro-switch to be activated in control unit. Radar An infrared sensor above the door detects an object (person, vehicle) within a specified distance from the door and opens the door automatically. This is an ideal solution for frequent vehicle or personal traffic. Often combined with automatic closing. Installed on the inside or outside wall above the door. External push button box An extra control box is installed outside the building or inside close to the door if the main control unit needs to be installed away from the door opening. Installed on the inside or outside wall beside the door. Photocell open door A set of photocells on pillars, on each side of the door. When a person or vehicle passes between the photocells, the beam is interrupted and the door opens. Photocells installed on pillars, away from the door. Pull-rope switch A pull-rope switch above the door opening can be operated from e.g. a forklift truck. Pulling the rope opens a closed door or closes an opened door. Installed on the inside construction above the door. Automatic closing A programmable timer that closes the door after a specified time, counted from either the fully open position and/or from passing through the photocell beam. Adjustable micro switches in control unit. 20 Description

21 Safety functions Safety edge Safety photocells 1-channel Safety photocells 2-channel As a standard, all doors that have the impulse-close function or any form of automated closing, are equipped with a safety edge. The pneumatic sensor in the bottom seal detects any obstruction under a closing door and reverses the door. Installed in the bottom seal. A set of a photocell transmitter and receiver is installed in the door opening. If the photocell beam is interrupted during closing, the door will stop in less than 30mm and reverse to the fully open position. Installed in the door opening. Two sets of photocell transmitter and receiver are installed in the door opening. If one or both photocell beams are interrupted during closing, the door will stop in less than 30mm and reverse to the fully open position. Installed in the door opening. Traffic lights - Red & Green Additional functions UPS battery backup Relay box If traffic through a door needs to be directed; two red and two green traffic lights can be installed to indicate traffic direction. From the side where a vehicle is first detected to approach the door, the green traffic light comes on. The opposing side shows a red traffic light. Traffic from this direction must give way to the other. Usually installed in e.g. parking garages. Installed on the inside and outside wall beside the door. When mains failure cannot be permitted or an increased risk of mains failure is predicted, the UPS battery backup system can be installed to store enough energy for 10 door cycles. Installed on the inside wall beside the door. A sealed connection box makes it possible to safely connect external high-voltage equipment. Warning lights - Red Two red warning lights giving information on the current door behaviour. Flashing light before or during door movement. Optional: Continuous light before and during door movement. Installed on the inside and outside wall beside the door. Warning lights - Green One or two green warning lights indicating the open position of the door by continuous light signal. Installed on the inside and/or outside wall beside the door. Description 21

22 2. Specifications 2.1 Dimensions Daylight width and daylight height The standard 542 overhead sectional door is delivered in the following size range: Standard door sizes Daylight width Daylight height Min.: 2050 mm 2100 mm Max.: 8000 mm 6000 mm Other sizes may be available on request Section sizes Section height: Top section height: Thickness: 600 mm mm trimcut 42 mm The door leaf height is achieved by trimcutting the top section Vertical cross-section 1. Top seal 2. Section joint with finger pinch protection and seals 3. Inner and outer sheet 4. Internal steel reinforcement, to provide positive fixing points 5. Window (optional) 6. High impact polystyrene frame 7. Panel truss - wind reinforcement (if necessary) 8. Step/lift handle 9. Insulation (CFC-free) 10. Bottom seal 22 Specifications

23 2.2 Windows and passdoor Windows DARP Number of windows For windows and passdoors, the daylight width is divided into a fixed grid. The number of windows depends on the daylight width of the door. Daylight width No. of windows mm mm mm mm mm mm mm mm 8 Optional: One window in the outer left or right side of section 3 only. DAOP DSR Passdoor Passdoor opening sizes Width: Height: Height from floor level: Position of passdoor 810 mm 1860 mm 2050 mm Daylight width Window no mm mm 1 or mm 1, 2 or mm 1, 2, 3 or mm 1, 2, 3, 4 or mm 3 or 4 Permissible overhead door sizes Minimum permissible DLW 2050 mm Minimum permissible DLH 2215 mm Maximum permissible DLW 6050 mm Maximum permissible DLH 6000 mm The passdoor is not available for the VLL track set. Specifications Threshold height: Lock: Door closer: 190 mm incl. bottom seal Depends on market MAB or equal Specifications 23

24 2.3 Door operation Selection guidelines for operation type Door size m2 Openings / day 1-5/day 5-10/day 10-15/day >25/day 0 10 / / / / / / / > / / > 42* * The maximum door weight that the operator can move is 750 Kg. This gives an approximate maximum area of the door of 42 m². Manual operation Electrical operation Automated operation Selection guidelines for Door operator Door openings/day 1. Over 300 days/year 2. Over 220 days/year * On request 24 Specifications

25 Door control systems - Selection guidelines Functions included A The following options can be individually selected to add functionality to the control unit. Functions optional A Open (by impulse) Open (hold to run) Stop Close (by impulse) Close (hold to run) Safety edge Open function One button function Display (diagnostics) Service indicator Standard Option / Available Door control systems - Selection guidelines for automation The Automation D-kits are packages of common combinations. These kits can also be supplemented by additions to D-kits. Automation D-kits D1 D2 D3 D4 D5 D6 D7 Interlocking Magnetic loop Traffic lights - Green + Red Warning lights - Red Additions to D- kits Warning lights Green Relay box Radar Standard Option / Available Complete kits Automation D-kits Basic control functions Interlocking Reduced opening External control functions External pushb. box Pull-rope switch Remote control open/stop/close Remote control 1-button function Automatic control functions Automatic closing Photocell open door Safety functions Safety photocell (1 or 2*) French safety logic Additional functions UPS Battery backup Relay box Standard Option / Available Specifications 25

26 Door control systems - Selection guidelines Functions included P Door control systems - Selection guidelines for automation Functions optional P Open (by impulse) Open (hold to run) Stop Close (by impulse) Close (hold to run) Safety edge (reverse) Open function One button function Standard Option / Available Complete kits Automation B-kits Automation C-kits Basic control functions Interlocking Reduced opening External control functions External pushb. box Pull-rope switch Remote control open/stop/close Remote control 1-button function Radar Automatic control functions Automatic closing Photocell open door Safety functions Safety photocell 1x Safety photocells 2x French safety logic Standard Option / Available Automation B- and C-kits C1* C2* C3* C4* C5* C6 C7 C9 C10 C11 C12 C13 C14 C15 C16 C17 C19 C20 C21 C22 Automatic closing Warning lights Red 2x Warning lights Green Safety photocell (1 or 2*) Magnetic loop Interlocking One button function Photocell open door Service counter * C1-C5 are equal to B1-B5 for 430 Door control system, however only one safety photocell possible on B-kits. Standard Option / Available 26 Specifications

27 3. CEN Performance The following tests have been carried out by the Swedish National Testing and Research Institute in Borås. For more detailed information and values, see ITT report: 0402-CDP Lifetime expectation door cycles or 10 years (in a normal industrial environment) Springs: door cycles 3.2 Resistance to windload EN12424 Without passdoor With passdoor Test result Class 3 Class 3 Class Pressure Pa (N/m 2 ) Specification 0 - No performance determined > 1000 Exceptional : Agreement between manufacturer and supplier Door size 4000 x 3450 mm 3.3 Resistance to water penetration EN12425 Without passdoor With passdoor Test result Class 3 Class 3* Class Pressure Pa (N/m 2 ) Specification 0 - No performance determined 1 30 Waterspray for 15 minutes 2 50 Waterspray for 20 minutes 3 > 50 Exceptional : Agreement between manufacturer and supplier * Danish Technological Institute (ref , dated 24/09/2002) CEN Performance 27

28 3.4 Air permeability EN12426 Without passdoor With passdoor Test result Class 2 Class 2 Class Air permeability dp at a pressure of 50 Pa (m 3 /m 2 /h) ,5 6 Exceptional : Agreement between manufacturer and supplier 3.5 Thermal transmittance EN12428 Steel Aluminium Thermal transmittance 1,0* 1,1* Door size 4000 x 4000 mm * These values are calculated values for a complete, installed, door of 4000 x 4000 mm and have to be confirmed by an official test. 3.6 Operating forces and safe openings EN12453 & EN12604 Opening gap mm Crushing force N Crushing force N Crushing force N 200 mm from lateral border right from outside In the middle of the door opening 50 mm passed passed passed 300 mm passed passed passed 200 mm from lateral border left from outside The crushing force is the force needed for the safety edge to be activated. The maximum force allowed, according to EN12453 safety in use of power operated doors is 400 N within a maximum period of time of 0.75 s. 28 CEN Performance

29 4. Building and space requirements 4.1 Building preparations Installation preparations The 542 overhead sectional door is shipped in parts and installed on-site. All necessary installation material is included. For every track type offers specific installation kits to position the door in the building facade. 1. Steel 2. Wood 3. Brick & Concrete Electrical preparations The manually operated door needs no electrical supply. For an electrically operated door, the following environment criteria and electrical supplies are required for the operator to function properly: CDM9 CDM5 (HD) Voltage supply: 230V AC 1-phase 50/60Hz / VAC 3-phases 50/60 Hz +/- 10% Power: 0,5 kw 0,38 kw (0,75 kw) Degree of protection: IP55, excl. connector IP 44 IP44 Allowed door weight, 400 kg 650 kg (1150 kg) max.: Temperature working range: -20 C to +60 C* -30 C to +60 C Operating factor: ED = 30% S3 10 min. intermittent ED = 30% S3 10 min. intermittent Mounting preparations: - Solid surface: steel/concrete. Alternative: motor plate *) Normal opening speed in a temperature down to -8ºC. In the temperature range -8 ºC to -20 ºC the opening speed is reduced during the first cycle to prolong the operator's lifetime. An optional heating element is available for a working range down to -30 ºC 4.2 Space requirements DLH = Daylight Height The height of the clear opening DLW = Daylight Width The width of the clear opening D = Depth The space between the inner side of the wall and the end of the horizontal track construction h = Excess height The extra space required above the daylight height. SL = Side space Left The space required for tracks beside the daylight width. SR = Side space Right The space required for tracks beside the daylight width. The grey marked area in the illustrations shows the free space required by door movement. Extra space requirements for electrically operated doors are stated in the operator specifications. Extra space requirements for passdoors are stated in the passdoor specifications. CEN Performance 29

30 4.2.1 Space requirements SL DLW 8000 mm DLH 6000 mm h 485 mm (if DLH 4500 mm) 510 mm (if DLH > 4500 mm) SL/SR* 100 mm D DLH mm * In case of an electrically operated door, SL or SR = 130 mm on side of safety pull. Side view Top view 30 CEN Performance

31 4.2.2 Space requirements HL DLW 8000 mm DLH 6000 mm h HL+320 mm (if HL 3400 mm) HL+370 mm (if HL > 3400 mm) SL/SR** 100 mm D DLH - HL mm ** In case of an electrically operated door with safety pull, SL or SR = 130 mm on side of safety pull. Side view Top view CEN Performance 31

32 4.2.3 Space requirements LL DLW 8000 mm DLH 6000 mm h* 265 mm (if 250 kg) 300 mm (if > 250 kg or passdoor) SL/SR** 100 mm D DLH mm *If the door weight exceeds 250 kg and/or if passdoor is installed: h=300 mm ** In case of an electrically operated door, SL and SR = 130 mm (because of safety pulls). Side view Top view 32 CEN Performance

33 4.2.4 Space requirements VL DLW 8000 mm DLH 6000 mm h DLH mm SL/SR 100 mm D 525 mm For doors DLW > 3000 mm, a supporting beam is installed for the balancing system. For doors DLW 3000 mm, manually operated, no beam is installed. Side view Top view CEN Performance 33

34 4.2.5 Space requirements VLL DLW DLH h SL/SR D 3000 mm 3300 mm DLH mm 100 mm 380 mm Side view Top view 34 CEN Performance

35 4.2.6 Space requirements Door operators CDM9 Installation locations Location of CDM9 operator CDM9 Space requirements Location Extra space requirements (mm).* Side room Head room Depth room 1 Left/right Left/right Centre Left/right Centre (Low Lift) * Space required in addition to the normal space requirements CDM5 Installation locations Location of CDM5 operator CDM5 Space requirements Location Extra space requirements (mm).* Steel motor plate (mm) Side room Head room Width Height Thickness 1 Left/right ,0 2 Left/right ,0 3 Centre ,0 4 Left/right ,0 5 Left/right (Low Lift) 450 / ,0 * Space required in addition to the normal space requirements. CEN Performance 35

36 5. Service These keys open doors to better business Regardless of their function, age or manufacturer, your industrial doors and dock loading systems have an important role in the flow of your business. That s why it makes sense to plan their maintenance long before the need for service occurs. A Key Customer Service agreement from is your best assurance of safe and trouble-free door and dock operation. By becoming a key customer, you not only reduce the risk of breakdowns, but also guarantee compliance with local regulations and the new harmonised EU standards. You also ensure that your doors and dock loading systems retain their classifications for wind load, air permeability, water penetration and more. Four types of Key Customer Service agreement Green, Yellow, Blue and Red allow us to tailor our service to your specific needs. Based on the role of your doors and dock loading systems, and the intensity with which you use them, you receive service that provides the perfect balance of economy, safety and security. Best of all, the maintenance is performed by s renowned team of service technicians. As a qualified specialist in industrial doors and dock loading systems, we have the knowledge and skills to service any door or dock, regardless of its type, age or manufacturer. With as a single source for all your door and docking equipment brands, you can easily reduce costs while increasing equipment availability. 36 Service

37 6. Index Door control systems Door control systems - Selection guidelines Door control systems - Selection guidelines for automation Door control system Door control system Door control system P Door control system Door control systems Door control systems - Selection guidelines Door control systems - Selection guidelines for automation Door control system Door control system A Door control system...18 A Access and automation...20 Additional functions...21 Air permeability...28 Automatic closing...20 Automatic control functions...20 Automation B- and C-kits...26 B Balancing system...15 Basic control functions...20 Bottom seal...8 Building and space requirements...29 Building preparations...29 C Daylight width and daylight height...22 Description...6 Dimensions...22 Door leaf...7 Door operation...24 DSR...10 E Electrical operation...16 Electrical preparations...29 External control functions...20 External push button box...20 F Features... iii Fixed sections...11 Foot lock...9 Frame section...10 G General...6, 12, 18, 19 H Handle...8 High lift...12 I Installation preparations...29 Interlocking...20 L Lifetime expectation...27 Lock bolt...9 Locks...9 Low lift...13 M Magnetic loop...20 Material...7 Relay box Remote control Resistance to water penetration 27 Resistance to windload S Safety devices Safety edge Safety functions Safety photocells 1-channel Safety photocells 2-channel Seals... 8 Section sizes Selection guidelines for Door operator Selection guidelines for operation type Service Side seal... 8 Space requirements Space requirements Door operators Space requirements HL Space requirements LL Space requirements SL Space requirements VL Space requirements VLL Special track sets Specifications Spring break device (SBD) Standard... 6 Standard colours... 7 Standard lift T Technical facts... iii Thermal transmittance Top seal... 8 Track sets Traffic lights - Red & Green Types of operation Cable break device (CBD)...15 CDM5 Installation locations...35 CDM5 Operator...19 CDM5 Operator series Door control system...19 CDM5 Space requirements...35 CDM9 Installation locations...35 CDM9 Operator...17 CDM9 Operator Door control systems...17 CDM9 Space requirements...35 CEN Performance...27 Chain hoist...16 Colours...7 Construction...7 Copyright and Disclaimer Notice. ii Cylinder lock...9 D DAOP...10 DARP...10 N Number of windows...23 O Operating forces and safe openings...28 Operating system...16 Optional colours...7 Options...6 P Panic lock...9 Passdoor...11, 23 Performance... iii Photocell open door...20 Pull-down rope...16 Pull-rope switch...20 R Radar...20 Reduced opening...20 U UPS battery backup V Vertical cross-section Vertical lift Vertical lift logistic W Warning lights - Green Warning lights - Red Wind reinforcement truss Windows... 10, 23 Windows and passdoor

38 is a leading international provider of door and logistics solutions. The carefully selected programme of doors and dock loading equipment, combined with profound application know-how and an unparalleled service offering, is the reason why more than a million customers have chosen as the preferred supplier for trouble-free operation around the clock.