Specification GS329 1

Transcription

1 N:\DEPTS\TECHPUB\SPECIFICATIONS\GS FM1 REVISED JUNE 2, :53 AM1 Specification GS329 1 myreflow.com Soldering System Manufacturer: Vitronics Soltec (Suzhou) Co., Ltd. Workshop II, 858 Zhujiang Road Suzhou New District, China Jiangsu Province. P.R. China Tel: Fax: myreflow.com 1 1

2 SPECIFICATION GS GENERAL INFORMATION MYREFLOW SERIES AVAILABLE MACHINES Zones Heating / Cooling Zones Total cooled length Total heated length Overall system length, Air ➊ Overall system length, Nitrogen prepared ➊ Overall system width Overall system heigth ➋ DIM # # mm/ inch mm/ inch mm/ inch mm/ inch mm/ inch mm/ inch MR /2 710/ / / / MR /1 355/ / / / MR 730 MR /3 8/2 1065/ / / / / / / / MR /3 1065/ / / / MR /2 710/ / / / MR /4 3550/ / / MR /3 1065/ / / / ➊ = In cold condition. Length increases with approximately 3 to 4 mm/ 0.12 to 0.16 inch in hot condition. ➋ = System height at conveyor height of 900 mm / 35.4 inch. ➌ = Depending on configuration On and off load lengths mm/ inch Net system weigth, Air ➌ kg/lb approx 2300/ / / / / / / / 5952 Net system weigth, Nitrogen prepared ➌ kg/ lbappro 2300/ / / / / / / /

3 1.1 - GENERAL INFORMATION MYREFLOW SERIES AREA OF APPLICATION The myreflow.com Soldering System is an in-line automatic machine, designed to solder printed circuit boards (PCB) in a reflow process. PCB s are transported by a conveyor system over the preheat, solder and cooling stations. The myreflow.com is designed to meet the European CE directives MATERIALS USED All customer-used chemicals must be compatible with the Vitronics Soltec used materials, such as: Fluorocarbon Elastomer, PVC (Polyvinyl chloride), PVDF (Polyvinylidene fluoride), steel, stainless steel and aluminium. To avoid severe corrosion in the machine only the use of solderpastes containing non corrosive or so called no-clean fluxes is allowed. These are fluxes which need not to be removed from the PCB after soldering GENERAL SYSTEM Hinged clamshell design with power lifts, provides full access to oven interior Total access to width adjust units, motor drive and chain return loops Full CE mark (applicable for EC/EFA countries only and when installed in-line) Integrated on-screen manual Colour grey white (RAL 9002) and grey (RAL 7036) Individual Zone Exhaust TM (patented) Alternative RAL colours Right-to-left machine configuration UL compliance for electrical enclosure myreflow.com 1 3

4 SPECIFICATION GS CONVEYOR SYSTEM EDGE RAIL STANDARD Pinchain conveyor pinlength 5 mm / inch 3.0 mm / inch Distance between pins 19 mm / 0.75 inch - Rail parallelism, total variation at any point on conveyor 1 mm/ 0.04 inch - Conveyor rails hardcoat anodised aluminium - Minimum board width 50 mm / 1.97 inch - Maximum board width 508 mm / 20 inch 610 mm / 24 inch Top side max. component height 40 mm / 1.57 inch - Bottom side clearance 30 mm / 1.18 inch - Pinchain conveyor height adjustable mm / inch - Conveyor speed range m/min - Conveyor speed measured value read-out - Conveyor speed accuracy +/- 0.5 % - Transport direction left-to-right right to left PCB drop detection by tracking on in- and outfeed sensor - Computer controlled chain lubrication - Motorised width adjust via PC - Motorized width adjust - 4 1

5 1.2 - CONVEYOR SYSTEM MESHBELT STANDARD Meshbelt (reduces bottom side clearance to 25mm) - Mesh belt: stainless steel flat flex belt 500 mm/19.68 inch 600 mm/23.62 inch Mesh type 12.7 x 1.8 mm/ 0.50 x 0.07 inch DUAL LANE ➊ fixed fixed fixed standard optional STANDARD Dual lane - Equal conveyor speed for both lanes - Minimum board width 50 mm / 1.97 inch - Maximum board width (equal) 206 mm / 8.11 inch 255 mm / inch Distance between rail 2 and 3 95 mm/ 3.74 inch - Rails 1 and 3 fixed position, rail 2 and 4 adjustable - Rail 1 fixed, rail 2, 3 and 4 adjustable Note: rail 2 and 3 mounted together -, only possible with 1 board support ➊ = Consult Vitronics Soltec for details. myreflow.com 1 5

6 SPECIFICATION GS BOARD SUPPORT SYSTEM FOR EDGE RAIL ONLY (NO MESHBELT) Required non-populated track clearance on board bottom side Board support system adjustable in width by motor Dual board support, adjustable in width and by motor, incl. park positions for 1 support Motorized width adjust via PC Park position underneath conveyor chain in case support not required (maximum 1 support) DIMENSIONS 3 mm / 0.12 inch Minimum distance to pin chain conveyor, for one and two support systems 50 mm / 1.97 inch Minimum distance between two support systems (center-tocenter) if not in park position 75 mm / 2.95 inch other dimensions on request Pin height support system 8.5mm / 0.33 inch 6 1

7 1.4 - HEATING MODULES 1.4 HEATING MODULES HEATERS Length of one heating zone Frequency controlled blower motors Heater type; fast response heaters Gas temperature control accuracy at steady state Gas temperature measurement by PT100 sensors in each zone Max. heating power per preheat zone (top and bottom) Cold start warm-up DIMENSIONS 355 mm / 14 inch 180 W Cr-Ni-steel +/- 1 C 9 kw 20 to 30 minutes ➊ Maximum gas temperature setpoint 350 C PID controls with PC-adjustable values for each zone Max. allowed temp difference between last soak zone and first peak zone 80 C Enhanced zone definition between last soak and first peak 120 C Max. allowed temp difference between two adjacent soak zones 50 C ➊ = Depending on temperature setting and configuration myreflow.com 1 7

8 SPECIFICATION GS COOLING MODULES Forced Convection; Top Forced Convection; Bottom Length of one cooling zone Frequency controlled motors, gas tight, type Gas temperature measurement by PT100 sensors in each zone Air Cooling Advanced Cooling Controlled cooling (only in combination with advanced cooling)➊ Setpoint 1st zone C Setpoint 2nd zone C Setpoint 3th zone C Gas temperature control accuracy at steady state PID controls with PC-adjustable values for each zone Factory Water Cooling DIMENSIONS 355 mm / 14 inch 180 W +/- 1 C Maximum water pressure supply < 800 kpa /8 bar Pressure differential ΔP at 17 ltr/min 5.83 kpa/0.0583bar Pressure differential ΔP at 33 ltr/min kpa/0.2035bar Minimal water supply (process zones only) Including GRS 17 ltr/min at 7 C 33 ltr/min at 7 C Connection 1 hose pillar Integrated Water Cooling External Chiller ➊ = Max 3 controls (in case of more cooling zones controls will be in serial). 8 1

9 1.6 - NITROGEN ATMOSPHERE 1.6 NITROGEN ATMOSPHERE Quick purge time to reach specified O 2 rest value Sealed upper and lower tunnel Flow meter for accurate nitrogen consumption measurement Integrated oxygen analyser with on screen display and alarm set points (auto scanning) Nitrogen performance (Depending on oven configuration, board dimensions, throughput rate, cell fan speed, nitrogen consumption) MR93N, 20, Hz fanspeed, 18 m³/h nitrogen consumption, DIMENSIONS 15 minutes <100 ppm in reflow Option 1.7 INTEGRATED GAS MANAGEMENT SYSTEM Flux management system, reduces maintenance intervals, incl. Exhaust stack filter 2nd Generation Condense Filtration System, includes active residue separation unit DIMENSIONS myreflow.com 1 9

10 SPECIFICATION GS REQUIREMENTS POWER SUPPLY REQUIREMENTS 8-ZONE 10-ZONE DIM MR 620 MR 710 MR 730 MR 820 Power supply V 400 V, 50/60 Hz, Supply tolerance + 10%, -10% Start-up power kva Slow start-up power kva Power at setpoint (approximately)➋ kva ZONE 14-ZONE DIM MR 840 MR 930 MR 1020 MR 1040 MR 1130 Power supply V 400 V, 50/60 Hz, Supply tolerance + 10%, -10% Start-up power kva Slow start-up power kva Power at setpoint (approximately)➋ kva ➋ = Depending on configuration, load and setpoint NITROGEN SUPPLY REQUIREMENTS Nitrogen supply pressure Nitrogen supply, maximum rate Nitrogen connection type DIM minimum 4.8 bar / 70 PSI 50 m³/hr / 1766 cfh ½ female NPT 10 1

11 1.8 - REQUIREMENTS EXHAUST Air Mode-No GRS - Exhaust volume at single connection point (maximum) Air Mode-GRS-Nitrogen - Exhaust volume at single connection point (maximum) Exhaust connection Output for externally mounted exhaust ventilator DIMENSIONS STATIC PRESSURE 450 m³/hr / 265 cfm 300 Pa 200 m³/hr / 118 cfm 100 Pa 165mm / 6.50 inch Option CONTROLS PC E-stop circuit Main circuit breaker disconnect DIMENSIONS Microsoft Windows XP based, flat screen monitor, harddisk, network adapter, keyboard and mouse included. 4 Emergency stop buttons at each corner of the machine Light tower Blue, red, amber, green and audible alarm Working hours counter Based on conveyor status Open in and outputs Programmable (4) OPERATING SOFTWARE ITEM Operating system Microsoft Windows XP Professional COMMUNICATION PROTOCOLS ITEM SMEMA electrical interface, for single and dual lane Siemens WMW interface for single and dual lane GEM/SECS II & HSMS interface myreflow.com 1 11

12 SPECIFICATION GS GENERAL CONTROLS AND SOFTWARE OPTIONS ITEM UPS power backup ➊ Full function recipe management Password protection Maintenance Scheduler Auto start-stop function through 7 day timer and year calendar Selectable main screen lay-out Alarm, event and Process Data Logging Trend Analysis On screen I/O map, with forcible outputs Power consumption monitoring communication from machine to user on selectable alarms Automatic machine and user software update notification through Internet Time and event based reporting via to selected users "How do I..?" integrated help function Remote connection through local network Digital wiring diagrams, accessible through on-screen I/O maps Management Information System Ability to link event log, data log and alarm log for better analysis SPC, statistical process control Remote connection through Internet access with Microsoft Netmeeting Four (4) profile K-type thermocouple ports with integrated Vitronics Soltec profiling software ➊ = UPS When the mainpower is "disconnected" the UPS will temporary take over all 240V functionality. This means that the product will be unloaded. After the product is unloaded, the machine will be switched off and an alarm is generated. 12 1

13 1.8 - REQUIREMENTS OPERATING CONDITIONS Ambient Temperature 18 to 40 C (64 to 104 F) Relative humidity 30% - 70% Atmospheric pressure 950 mbar mbar SHIPPING AND INSTALLATION MYREFLOW.COM See "Available machines" myreflow.com 1 13

14 SPECIFICATION GS DIMENSIONS MYREFLOW 365.5, Exhaust ø 165 A = Air N = Nitrogen 1700 TopView All dimensions in mm POS A B C D MR620A, MR620N, MR710A, MR710N, MR730A & MR820A SideView Nitrogen A FrontView B D MR730N, MR820N, MR930A & MR1020A 12 SideView Plant Water Connection In/Out 1 G Main Electrical Supply A B D SideView MR930N, MR1040A, MR1130A & MR1020N 14 * * = PCB width Conveyor to floor A B D MR1040N & MR1130N A C B D C 16 ** All specifications are subject to periodic review and may be changed without notice. Vitronics Soltec assumes no obligation for specifications contained herein. All customer-used chemicals must be compatible with materials used by Vitronics Soltec. 14 1