Model No. VS2002DL NEW. List Price Exc. VAT Inc. VAT. High Level Commercial Vehicle Support Stands

Transcription

1 JACKING & LIFTING Auto Rise Ratchet Axle Stands (Pair) Ratchet type axle stands, with cast iron support posts. Auto Rise operated by lever, allowing gas assisted post to rise. Angled treads in post prevent accidental release of load - the more weight applied, the tighter the post is locked. Full width crutch for safe support of load. Sold in pairs. Each/Pair Ratchet Type Axle Stands (Pair) with Safety Pins Min./Max. Working Height 3tonne 5tonne 10tonne AAS3000 3/6tonne 340/510mm AAS5000 5/10tonne 385/615mm AAS /20tonne 500/765mm Folding Axle Stands (Pair) per Stand Min./Max. Working Height: 275/360mm. : 4tonne per pair. Steel construction. Folds down for ease of storage. Locking safety pin. Sold in pairs. AS2000F EXC INC. VEHICLE SUPPT & AXLE STANDS IMPTANT SAFETY WARNING! WHEN JACKING A VEHICLE ALWAYS USE AXLE STANDS AND CHOCKS. NEVER GET UNDER A VEHICLE SUPPTED ONLY BY A JACK. 3tonne 6tonne VS2002DL CHECK OUT SEALEY TOOLS ON F OUR JACKING SAFETY GUIDE CRECT CRECT CRECT Ratchet type with cast iron support posts. Fitted with safety locking pin. Tough steel plate welded bases. Sold in pairs. Each/Pair Min./Max. Working Height VS2002DL 2/4tonne 275/425mm VS2003DL 3/6tonne 280/425mm VS2006DL 6/1 380/605mm INCRECT INCRECT INCRECT High Level Supplementary Stands 4tonne Steel stand. Pin and chain load support. Full width crutch. Designed to support part of a vehicle that is being used on a lift where free access is required. Stands also help prevent the tipping/rocking of the vehicle. These stands should not be used to support a vehicle on their own. Sold as singles, but MUST be used in pairs. Each/ Pair Min./Max. Working Height AS2000HS 2/4tonne 1220/1800mm AS4000HS 4/8tonne 1220/1855mm AS2000HS High Level Commercial Vehicle Support Stands Heavy-duty high level support stands. Safely supports vehicles when wheel free operations are being carried out. Independently UK load tested. Sturdy welded steel construction for superior safety and strength. Three types of large interchangeable crutches for good load distribution. Supplied with captive pin load support. Fitted with retracting castors for easy manoeuvrability. Suitable for commercial and public service vehicles. Sold as singles, but MUST be used in pairs. Each Min. Working Height (Shallow/ Deep/V) Shallow Saddle Deep Saddle Max. Working Height (Shallow/ Deep/V) ASC50 Extended ASC50 5tonne 1315/1315/1340mm 1835/1835/1860mm ASC70 7tonne 1315/1315/1340mm 1835/1835/1860mm ASC /1340/1365mm 1860/1860/1890mm sealey sealey tools

2 Composite Creepers One piece, moulded high impact polymer creeper. Padded headrest. Low profile. SCR80 Torch worth 11.95! 1W LED ADJUSTABLE FOCUS TCH ON SELECTED ITEMS ON THIS PAGE! Deluxe 36" Folding American Style Creeper with 6 Wheels LED SCR80S Size (L x W x H) Wheels Car Ramps 1tonne per Ramp per Pair SCR80 has two integral tool trays. SCR80S 915 x 410 x 95mm SCR x 480 x 115mm Low Level Creeper, Seat & Kneeler Heavy-duty steel framework. Converts from creeper seat, to a traditional creeper and to a kneeler. Ø70mm Composite castors with ball bearing swivels. Size (L x W x H): 730 x 320 x 610mm. SCR tonne Telescopic Low Entry Bottle Jack 128mm Min./Max. Height: 128/223mm. Telescopic two-stage ram for higher maximum lift. Cast base with threaded components. 4pc Operating handle. BJ10LE EXC INC. 10tonne EXC INC. Fully tested and fitted with overload valve. Base and reservoir machine welded. Threaded pump assembly. 3pc Handle. Service kits available. Ø60mm Composite castors with ball bearing swivels. Size (L x W x H): 910 x 425 x 100mm. Folded Size (L x W x H): 450 x 425 x 120mm. SCR75F Bottle Jacks Deluxe Steel Creeper with 6 Wheels & Headrest Heavy-duty steel frame. Size (L x W x H): 1135 x 510 x 185mm. SCR Min./Max Height 5pc Lifting Kit trolley jack with short wheel base has a lifting range of 140mm to 340mm. 1tonne axle stands (x2) have a combined weight capacity of (Min/Max Working Height: 290/390mm). Folding wheel chocks (x2). L-bar wrench with 17 & 19mm socket. JKIT SBJ2W 172/372mm SBJ3W 3.5tonne 172/372mm SBJ5W 5tonne 212/468mm SBJ15W 15tonne 230/497mm SBJ30W 30tonne 245/495mm SBJ5W EXC INC EXC INC. Manufactured from 3.5mm steel section. Ramps stack together and will stand upright for storage. Maximum Tyre Width: 200mm. CAR EXC INC EXC INC. Get the Sealey app on ios & Android Promotion Code: SUM17 s exclude unless stated otherwise 27

3 JACKING & LIFTING Low Entry Trolley Jacks with Rocket Lift 3tonne Standard Chassis Trolley Jack 3tonne 74mm Min./Max. Saddle Height: 74/514mm. Twin piston Rocket Lift feature brings saddle to maximum height in just 6 strokes. Universal joint release mechanism allows safer, more controlled lowering of jack. Profiled lifting arm gives low clearance height of just 74mm making it suitable for sports and custom cars. Fitted with an overload valve for added safety. Colour 2001LEBL Blue LEHV Hi-Vis Green LE Hi-Vis Orange LERE Red Premier Trolley Jack Min./Max. Saddle Height: 95/410mm. Chassis Length: 615mm. Lift-and-twist dead man s lowering mechanism operates via T shaped handle to provide a smooth, controlled lowering of the load and prevent accidental operation. PFJ Low Entry European Style Trolley Jacks Lift-and-twist Dead Man lowering mechanism operates via D shaped handle and prevents accidental lowering; lowers rapidly when no load is attached and provides smooth, slow, controlled lowering with a load. Foot pedal for quick approach of the lifting saddle to the vehicle. Includes removable rubber saddle pad and built-in tool tray. Min./Max Height Weighs Just 20kg 95mm 3tonne 5tonne Chassis Length FOLDING AXLE STANDS (PAIR) 2TONNE CAPACITY PER STAND AS2000F EXC INC. 1W LED ADJUSTABLE FOCUS TCH LED MECHANIC S GLOVES PADDED PALM MG796XL Farm Jacks 2500kg Reversible ratchet mechanism enables jack to be used for lifting or lowering. Upper jaw, adjustable on beam, allows jack to be used as a clamp. Versatile, lightweight unit also suitable for pulling tree stumps and tensioning fences. 2000ESLE 75/520mm 960mm ESLE 3tonne 100/570mm 1070mm ES 3tonne 140/610mm 1100mm ES 5tonne 150/583mm 1305mm ES 10tonne 170/576mm 1605mm tonne 2000ESLE Jack Min./Max. Saddle Height: 133/515mm. Single-piece hydraulic unit with heavy chassis design. Fitted with safety overload valve and pump-through valve to prevent handle locking at maximum ram extension. Ideal for loaded vans up to 3.5tonne GVW. Supplied with Ratchet Type Axle Stands, 3tonne (3000kg) capacity per stand (6tonne (6000kg) per pair). Axle Stand Min./Max. Working Height: 285/420mm. 3010CX Min./Max. Height Safety System 10tonne Beam Size 10tonne Air Jack FJ48 Min./Max. Height: 447/1300mm. Extension: 561mm. Max. : 10tonne. Ideal for lifting and heavy plant, tractors and commercial vehicles. Multiple lifting and locking positions achieved using extension tube with multi-position pin support. Removable two piece handle. Requires 200psi of air pressure to reach optimum performance. AJS EXC INC. 2.5tonne FJ48 115/1030mm 1200mm FJ60 115/1350mm 1500mm FJ48 MECHANIC S GLOVES PADDED PALM MG796XL tonne FJ EXC INC. 28 sealey sealey tools

4 3tonne Premier Air Operated Fast Jacks Three Stage 3tonne PAFJ3 450MM 3/8"SQ DRIVE BREAKER BAR AK tonne Air Operated Bottle Jack 18tonne 20tonne Air Operated Trolley Jack FOLDABLE MECHANIC S WK MAT 20tonne Min./Max. Height: 135/450mm. PAFJ3S Air Consumption: Internal military gauge steel telescopic interlocking core. Overload safety and air vacuum valve for rapid lowering. Fast lift, can reach maximum height in 25 seconds. Wheels Handle Type PAFJ3 x 1 Long PAFJ3S x 2 "D" Type Folding Cranes Folds for easy storage. Side pump access with removable handle. Delivered in knock-down form. 1tonne LOAD SLING ADJUSTER 680KG CAPACITY LS Min./Max. Height: 261/520mm. Air Consumption: 9.5. Features dead man s control and sectional pump handle for manual operation. YAJ18S FOLDABLE MECHANIC S WK MAT VS EXC INC. VS Min./Max. Height: 228/457mm. Air Consumption: 9.5. Features dead man s controls and multi-position locking handle. Supplied with 20/60/90mm extensions as standard. YAJ20B EXC INC. Premier Folding Engine Cranes 1tonne Heavy-duty forged hook. Dead man s control. Fast folding. Beam can be set in four positions. 225 Swivel pump. 14.4V 3/8"SQ DR CDLESS IMPACT WRENCH 150LB.FT CP PFC101 SC10 1tonne PH SC10 PFC101 1tonne PFC tonne Premier Engine Crane Fixed Heavy-duty forged hook. Beam can be set in four positions Rear swivel wheels and handle. Two pumps one for slow, safe controlled lifting and one quick lift. PFC EXC INC. 18V 4AH 1/2"SQ DRIVE CDLESS LITHIUM-ION IMPACT WRENCH 650NM 2 BATTERIES CP tonne 12V RoadStart Emergency Power Pack 900 Peak Amps Hi-Vis Green 12V 1W LED ADJUSTABLE FOCUS TCH LED Cable & Clamp Length: 0.72mtr. LED Battery condition, polarity check. Integral LED work light for use at night. Fitted with two 12V power sockets that will accept any 12V device fitted with a vehicle accessory socket plug. Features a USB outlet (5V/1A). RS1312HV EXC INC. Get the Sealey app on ios & Android Promotion Code: SUM17 s exclude unless stated otherwise 29

5 JACKING & LIFTING Telescopic Air Operated Jacks MECHANIC S GLOVES PADDED PALM MG796XL mm YAJ15-30F 30tonne 40tonne YAJ10-40LELR 130mm 20tonne Air Operated Trolley Jack Min./Max. Height: 215/456mm. Air Consumption: Powerful and reliable. Lifts heavy plant, tractors and commercial vehicles. Extensions: 20, 50, 100mm. YAJ tonne FOLDABLE MECHANIC S WK MAT VS Min. Max Height YAJ15-30F 30tonne 150/409mm YAJ10-40LELR 40tonne 130/409mm Folding Wheel Step Weight : 225kg. Ideal for 4x4 s. Platform Size: 210 x 560mm. Wheel Diameter: 14" to 20". Will fit tyres up to 10" deep. STS EXC INC. 32mm x 4.9mtr Polyester Webbing Ratchet Tie Down with J Hooks 1200kg Load Test 2 Pairs 1200kg 32mm 4.9mtr Load Test: 1200kg. Webbing Length: 4.9mtr. TD41248JD EXC INC. Universal Light Mounting Brackets Number Plate Fitting 25mm x 5mtr Ratchet Tie Down & Flat Bungee Cord Set Load Test: 800kg. TD285SBD EXC INC. 25mm x 4mtr Polyester Webbing Ratchet Tie Down with S Hooks 800kg Load Test 800kg 25mm 5mtr EXC INC. 25mm x 3mtr Auto Retractable Ratchet Tie Down Auto rewind feature at a push of a button retracts the webbing, leaving the unit neat and tidy. ATD EXC INC. Manufactured from polyester webbing with stitched reinforcement around hooks. Suitable for securing loads and tarpaulins onto flat-beds or trailers and 800kg 25mm 4mtr for general load restraint. Load Test: 800kg. Webbing Length: 4mtr. Quantity TD284SD 1 Pair TD484SD 2 Pairs LED Off-Road Work Spotlights TD484SD 600kg TD284SD DBL01 Simple, lightweight solution for mounting driving lamps or LED light bars to most cars, vans and commercial vehicles. For compatible work lights, please see right. Dimensions (L x H x D) DBL02 DLB x 125 x 55mm DLB x 120 x 90mm A B C D Description Power Lumen Output A WL12W Spotlight with 4 x 3W Epistar TM high power LEDs 12W 840lm B WL18W Floodlight with 6 x 3W Epistar TM high power LEDs 18W 1080lm C WL24W Floodlight with 8 x 3W Epistar TM high power LEDs 24W 1440lm D WL48W Spotlight with 16 x 3W Epistar TM high power LEDs 48W 3450lm sealey sealey tools

6 PRESSES 4tonne Bench Type Hydraulic Press without Gauge Ø115MM ANGLE GRINDER 900W SG Table Aperture: 70mm. Ram Stroke: 120mm. Ram Ø: 20mm. Working Table Width: 335mm. Detachable pump and ram. Minimum/Maximum Ram to Table: 115/330mm. YK4B tonne EXC INC. 10tonne Bench Type Hydraulic Press Ø115MM ANGLE GRINDER 900W SG Table Aperture: 115mm. Working Table Width: 335mm. Ram Stroke: 180mm. Overall Height: 1060mm. High quality industrial press ideal for pressing, bending and extruding. Supplied with pressure gauge. YK10B tonne EXC INC. 15tonne Premier Hydraulic Press Bench Type 15AMP 12/24V AUTOMATIC BATTERY CHARGER SDC Table Aperture: 140mm. Working Table Width: 430mm. Ram Stroke: 170mm. Supplied with flat pressing plate/v-blocks. PPB tonne EXC INC. Hydraulic Presses Detachable pump and ram allowing hydraulics to be used for other purposes when press is not in use. YK10F 7.5AMP 6/12V AUTOMATIC BATTERY CHARGER SDC tonne 20tonne YK20F 30tonne Floor Type Hydraulic Press Table Aperture: 154mm. Working Table Width: 460mm. Ram Stroke: 150mm. Overall Height: 1950mm. Steel frame construction with side mounted hydraulic pump unit. Sliding hydraulic ram assembly giving 200mm of lateral travel for off-centre pressing applications. Includes flat pressing plate/v-blocks. Fitted with ram pressure gauge. YK30XF AMP 12/24V AUTOMATIC BATTERY CHARGER SDC tonne Working Table Width Ram Stroke YK10F 10tonne 454mm 180mm YK20F 20tonne 550mm 185mm Premier Floor Presses No s. PPF20 & PPF30 only: Ram Stroke: 195mm. Heavy-duty steel frame construction with 2-speed manual operated hydraulic pump unit to provide both fast approach and precision pressing. Patented V-block guides and adjustable work area with removable tray. Frame head fitted with ram pressure gauge. Storage for press pins included in frame. Supplied with flat pressing plate/v-blocks. 12V COMPACT AUTO DIGITAL BATTERY CHARGER EXC INC. 20tonne 30tonne No s. PPF301 & PPF501 only: Heavy-duty steel frame construction with integral air motor powering hydraulic pump unit. 2-Speed manual operation via two foot pedals. Sliding hydraulic ram assembly giving lateral travel for off-centre pressing applications. Patented adjustable work area fitted with gas struts for easy positioning with removable tray. SMC PPF30 Type Table Aperture Lateral Ram Travel Working Table Width PPF20 Hydraulic 145mm 20tonne - 530mm PPF30 Hydraulic 145mm 30tonne - 530mm PPF301 Air Hydraulic 165mm 30tonne 250mm 530mm PPF501 Air Hydraulic 165mm 50tonne 230mm 720mm Get the Sealey app on ios & Android Promotion Code: SUM17 s exclude unless stated otherwise 31

7 PARTS CLEANING Magnetic Stainless Steel Parts Strainer Stainless steel strainer ideal for storing nuts, bolts, parts or tools whilst cleaning. Magnetic base helps secure the strainer safely. Diameter: 270mm. SMS ltr Bench/Portable Parts Cleaning Tank One-piece tank with triple baked finish and fully sealed magnetic drive pump unit with replaceable impellor. Fitted with flexible, metal delivery nozzle. Tank includes removable shelf. Tank Size (L x W x H): 395 x 290 x 210mm. Overall Height: 225mm. Pump Output: 90ltr/hr. Min./Max. Working : 7/15ltr. Supply/Motor Power: 230V/26W. SM mm Sheet Metal Folder/ Bench Mounting 700mm Removable Folding Plate 7.95 EXC INC. NITRILE GAUNTLETS 330MM CUFFED PAIR SSP ltr EXC INC. Bench or vice mounting sheet metal folder, fitted with mounting plates. Capable of bending 1mm steel sheet of limited length. Unique patented endless design and removable folding plate allows the user to fold any length of sheet metal up to 1mm thick. Adjustable fold plate to help achieve the cleanest fold possible. Ideal for the small garage or restoration operation. : 20 Gauge Sheet, Ø1mm Rod. TS PATENTED & EXCLUSIVE TO SEALEY Parts Cleaning Brush with Hose Fits onto the flexible spout of Sealey parts cleaning tanks (except SM21) and allows a stream of fluid to pass through the bristles for extra cleaning power. Supplied with hose, adaptor nipple and two hose clips. SM ltr Mobile Parts Cleaning Tank Fully sealed electric motor with magnetic drive pump unit. Lid features self-latching fusible link which automatically snaps lid shut in the event of a fire. Includes removable shelf and small parts basket. Flexible metal nozzle directs solvent over work. Stand fitted with four Ø100mm castors for easy manoeuvrability, two of which are lockable. SM EXC INC. 3PC AVIATION TIN SNIP SET AK EXC INC. 50ltr PVC CHEMICAL HANDLING GAUNTLETS SSP EXC INC. 25ltr Emulsifiable Degreasing Solvent High quality, general purpose low odour cleaning solvent. Also suitable for engine cleaning. AK EXC INC. 50ltr Air Operated Mobile Parts Cleaning Tank with 65ltr Reservoir 50ltr PVC CHEMICAL HANDLING GAUNTLETS SSP Mobile unit which can easily be taken to work area. Air operated unit can be charged and then used without air supply for a limited period. Includes brush for cleaning workpiece and air blow gun for fast drying. Supplied with removable shelf and tray. SM Professional Conduit Bender Professional folding A-frame conduit bender with vice. Suitable for galvanized and black enamel conduit. Supplied with three machine cast formers 20, 25 and 32mm which will bend conduit in accordance with BS 4568 up to a maximum length of 1100mm. The vice aids cutting lengths and threading. Extended (W x D x H): 510 x 1030 x 1115mm. Folded (W x D x H): 510 x 145 x 1210mm. PCB ltr EXC INC EXC INC. 32 sealey sealey tools

8 SHOT BLASTING Economy Type Sandblasting Gun with 6mm Nozzle Suitable for cleaning small areas such as wheels or chassis members. Accepts a variety of abrasives including sand, chilled iron grit and other proprietary types of beading. SSG8E Portable Shot Blasting Kit 22kg Large capacity hopper with integral hose storage. Supplied with 4.5mtr of grit hose and fitted with a heavy-duty shot blasting gun. SB Shot Blasters with Water Traps & Wheels Pressurised tank for maximum power. Supplied with 2.4mtr rubber hose, five ceramic nozzles and in-line water trap for moisture-free grit blasting. Also includes bayonet air line coupling and air flow regulator. Accepts a variety of grits up to 700microns and is suitable for stripping rust and paint from wheels, chassis, panels and other corroded/painted surfaces EXC INC EXC INC. 18kg Portable Soda Blasting Kit HOODED COVERALL XL SSP267-XL 3.95 Extra Heavy-Duty Recirculating Sand Blasting Kit Features feathering action. Features a forced air powered recirculation system and is additionally fitted with a vacuum tube to increase suction power allowing gun to be used at an angle. Supplied with a set of rubber nozzles for sealing the gun head to the panel. Supplied with 700g bottle of grit. SG Pressurised tank for maximum power. 1.5mtr Hose and ceramic nozzle with shut off valve. Also includes bayonet air line coupling and airflow regulator. Air Pressure: 35-90psi. Air Consumption: 8. Maximum Pressure: 100psi. PSB EXC INC. 92kg 18kg SB998 SB997 37ltr SB998 75ltr EXC INC. Shot Blasting Cabinet Heavy-duty steel cabinet, toughened glass viewing screen and integral low voltage illumination. Large side door provides easy access for bulkier items. Ø60mm Dust extraction port. Heavy gauntlets provide hand protection and cabinet is supplied with sand blasting gun, four ceramic nozzles and five visor covers. Suitable for glass beads, silicon carbide, aluminium oxide and silica sand only. Overall Size (W x D x H): 890 x 570 x 1380mm. SB EXC INC. 25kg Shot Blasting Grit - Bag Complies with COSHH SI Not suitable for use in shot blasting cabinets. B/25KG EXC INC. 25kg Blasting Soda - Bag Soda leaves a rust inhibitor behind for up to 6 weeks. Grade/Size: Extra Coarse/285microns. SBG25KG EXC INC. Shot & Soda Blasting Kit Kit includes: 37ltr Shot Blaster with Water Trap. Soda Blasting Conversion Kit for SB997 Leather Welding Gauntlets Lined - Pair Safety Goggles Indirect Vent Disposable Dust Mask FP2S - Pack of kg Blasting Soda - Bag. SBKIT EXC INC. Get the Sealey app on ios & Android Promotion Code: SUM17 s exclude unless stated otherwise 33

9 MOTCYCLE Universal Rear Wheel Stand with Rubber Supports Universal Front Wheel Stand Heavy-Duty Motorcycle Front Wheel Chock Lifts and stabilises any dual swing arm motorbike quickly and easily. Fitted with width and angle adjustable rubber support pads. Min./Max. Width: 245/320mm. RPS V Motorcycle Digital Battery Tester Compact device which accurately tests the motorcycle s battery. No heat, no sparks and no misdiagnosis. Just key in the battery rating from the top of the battery and results are displayed on LCD screen. Includes a facility to print results via PC. No internal battery and will test batteries with a residual charge of just 8V. Supplied with PC software and instruction manual in storage pouch. MC Double End Long Reach Spark Plug Box Spanner Set 3pc Double end, traditional style, long reach spark plug box spanners with L-bar. Size: 14 x 16, 16 x 18, 17 x 21mm. Length: 150mm. MS Motorcycle Front Wheel Chock Suitable for wheels with tyre widths mm and diameters 17"-21"( mm). Base can be permanently bolted to the floor (fixings included). Features a detachable upper assembly that can be easily stored and re-attached when required, stabilising motorcycles without the need for side or centre stands. FPS EXC INC. 12V EXC INC EXC INC EXC INC. Features width adjustment from 210 to 280mm, making it suitable for almost all motorbikes. Design ensures rim and tyre protection at all times. Once the bike is supported, allows easy removal and cleaning of front wheel. Please note all front paddock stands need to be used in conjunction with a suitable rear stand to ensure bike stability (See No s RPS1 or RPS2). FPS Motorcycle Helmet & Gear Tidy MS080 Powder coated steel construction, for added corrosion resistance. Wall mounting units designed to organise the storage of gloves, clothing and helmet. Triangle Dirtbike Stand Quick and easy to use. Simply hook into the rear axle. Locating Pin Height: 380mm. Suitable for use on bikes that have rear axle inner diameters of 11.5mm, 14.5mm and 18.5mm. To move the bike again, simply un-hook the stand from the axle. MS EXC INC. Side Stand Type Motorcycle Dolly Motorcycle dolly holds a single motorcycle with a side stand, weighing up to 565kg. Easy to manoeuvre around the workshop or garage. Front and rear lever operated wedge gates allow for easy loading and unloading. Five position side stand platform to fit varied length side stands. Front/rear steel pins to keep the motorcycle on the dolly during moving, and smooth rolling dual castor wheels. Overall Dimensions (L x W x H): 2120 x 770 x 90mm. Loading Track Dimensions (L x W x H): 2000 x 200 x 50mm. MS EXC INC EXC INC. MS kg Fully adjustable to fit wheels 15"-18"( mm). Minimum/Maximum tyre width 110/130mm. Chock can be used freestanding or fixed to any hard surface (fixings not included). Please note: Motorcycle must also be secured using tie-down straps. FPS MS MS Ø43-102mm Motorcycle Oil Filter Claw Wrench Chrome polished carbon steel construction with 3/8" & 1/2"Sq drive. Also suitable for use with a 21mm spanner. Claws grip filter tighter as more torque is applied. Fits a range of popular motorcycle can filters ranging from 43 to 102mm. MS EXC INC EXC INC. 34 sealey sealey tools

10 12, 14, 17, 19, 22 & 24mm Motorcycle Spindle Tool Prevents spindle from spinning when tightening or loosening wheel nut. Use appropriate socket on free end of tool to hold spindle. Six sizes to fit a variety of motorcycle makes and models. MS Motorcycle & Bicycle Wheel Balancer & Truing Stand Professional dual purpose wheel balancer and truing stand. Suitable for most motorcycle wheels. Ideal for the workshop technician or competent DIY enthusiast. Includes two cones and spindle for precise, easy alignment and balancing. Enables the accurate balancing after tyre fitting and truing of rebuilt, warped or buckled spoke wheels. Uses gravity to find the heavy point of a wheel and tyre. Threaded centring stabilizer bolts to securely hold the wheel whilst truing the rim. WTS EXC INC. 14pc Motorcycle Brake Piston Removal Kit EXC INC. 9pc Spoke Wrench Set Specially designed spoke wrench with eight interchangeable sized heads. Suitable for adjusting spoke tension and correcting buckled wheels. Sizes: 5.4, 5.6, 5.8, 6, 6.2, 6.4, 6.6, 6.8mm. MS SPOKE WRENCH MS Motorcycle Brake Piston Removal Pliers 9.95 EXC INC. Motorcycle Brake Bleeder One man bleeding/servicing of hydraulic brakes and clutches. The kit utilises a small non-return valve and two connector hoses that attach to the scooter or motorcycle bleed nipple. As the brake/clutch are bled the valve prevents the used fluid and air being drawn back into the system. MS Motorcycle Disc Brake Spreader Tool Essential tool for retracting the brake piston to allow insertion of new brake pads. Suitable for most front and rear motorcycle brake calipers. Maximum Spread: 50mm. MS pc Rim Protector Moulded protectors with connecting cord. Designed to reduce the risk of damage to motorcycle wheel rims when removing or fitting tyres with tyre levers. VS EXC INC EXC INC EXC INC. Motorcycle Twin-Clamp Cable Oiler Extract brake caliper pistons without risk of damage to outer face of piston. Includes 12 adaptors to suit different sized pistons. Detachable slide hammer for impact removal. : Ø19-30mm. MS Motorcycle Pulley Holders Suitable for flywheel and clutch pulleys on a large range of motorcycles. Adjustable strap for use on different pulley sizes. Rotate handle so foot contacts against pulley to secure, rotate in the opposite direction to release EXC INC. VS1811 VS1811 Ø45-120mm VS1813 Ø30-160mm Extract brake caliper pistons without risk of damage. Clamp screw allows pliers to be fixed into cup of piston for added pulling power. : Ø mm. VS ltr Motorcycle Portable Fuel Tank Features 1ltr tank, 950mm hose, two hose clamps and on/off tap. MS Dual Entry Carburettor Accessory Kit for MS EXC INC EXC INC EXC INC. MS029DCK Twin-clamp cable oiler for use with spray type silicone or oil on motorcycle cables. MS Motorcycle Ground Anchor Heavy-duty hardened steel bolt down anchor with key operated locking pin. Supplied with all fixings. Contents: Anchor, Security Bolts, Locking Pin, Ball Bearings, Keys (x2). MCGA EXC INC EXC INC. Get the Sealey app on ios & Android Promotion Code: SUM17 s exclude unless stated otherwise 35

11 MOTCYCLE Motorcycle Portable Folding Workbench/Pit Table 360kg Working height of 460mm, ideal for servicing/maintenance. Loading ramp doubles as a convenient workshop stool. Folding design allows compact storage where workshop space is limited. Suitable for professional workshops, mobile mechanics, enthusiasts, track days or as a display table in showrooms. Folded dimensions (L x W x D): 1100 x 600 x 150mm. Weight: 38kg. MCW Hydraulic Motorcycle Lifts All steel construction with foot operated, integral hydraulic pump and ram assembly. Fitted with safety lock device to fix platform at three working heights. Support platform fitted with full width loading ramp. Base assembly fitted with transport wheels and lock-downs to prevent lift from moving during use. 2 DRAWER PTABLE TOOL CHEST WITH 90PC TOOL KIT S No, MC365 only suitable for motorcycles with a centre stand. MC454 suitable for motorcycles with a centre stand or paddock stand. Min./Max Height RATCHET TIE DOWNS TD484SD kg EXC INC. MC kg 220/760mm MC kg 190/660mm Folding Steel Ramps 500kg per Pair MC365 Scissor Motorcycle Lift with Frame supports 500kg RATCHET TIE DOWNS TD284SD Min./Max. Lift Height (without Frame Supports): 110/400mm. Min./Max. Lift Height (with Frame Supports): 210/508mm. Maximum Frame Dimensions (W x D): 680 x 360mm. MC Single Sided Motorcycle Lift 450kg Space saving design. Two locking positions for supporting the motorcycle over extended periods on the lift. With this lift it is possible to remove both wheels, front forks, steering assembly, rear swing arm and suspension units as well as the engine. Benefits from being portable and can be used anywhere with a hard level floor. Ideal for use with the Sealey range of wheel chocks to assist supporting the motorcycle, whilst adjusting the frame supports and securing to the lift. Min./Max. Lift Height (without Frame Supports): 65/740mm. Min./Max. Lift Height (with Frame Supports): 165/840mm. Frame Height: 920mm. Maximum Frame Width: 980mm. MCL Motorcycle & Mini Tyre Changer 500kg EXC INC. MOTCYCLE FRONT WHEEL CHOCK FPS kg EXC INC. Manufactured from strong, durable powder coated steel. Folded Dimensions (L x W x H): 890 x 230 x 150mm. Extended Dimensions (L x W x H): 2000 x 230 x 50mm. Maximum load 250kg single ramp or 500kg per pair. Features a strap and hook. FCR kg Wide Tri-Folding Motorcycle/Trike/ATV & Mini Tractor Aluminium Loading Ramp 500kg Manufactured from strong durable yet lightweight aluminium. Provides safe and easy ramp access for inline and multi axle vehicles. Folded Dimensions (L x W x H): 1760 x 380 x 70mm. Extended Dimensions (L x W x H): 1760 x 1140 x 20mm. Features safety securing chains and extended claws at one end to help secure ramp when in use. FLR680T EXC INC. 680kg EXC INC. Manual type tyre changer suitable for a wide variety of tyres and wheels including those fitted to motorcycles, quad bikes, go-karts and golf buggies. Works on bearing or hub centred wheels and supplied with two centre posts. Min./Max. Wheel Size: Ø102/524mm. Includes manual bead breaker and is supplied with tyre bar for mounting and de-mounting. Fast and simple operation. To prevent damage to the rims of the alloy wheel, use TC963 Tyre Bar. TC EXC INC. 36 sealey sealey tools

12 COMPRESSS Belt Drive Compressors with Front Control Panels hp 50ltr SAC3503B 100ltr SAC3103B Twin capacitors and a centrifugal switch aid trouble free start up on a good 13Amp supply. Pump features heavy-duty full cast cylinders, capped by alloy heads for improved heat dissipation and long life. Features an easy to use bespoke control panel with two outlets, one regulated and one direct. Heavy-duty pneumatic wheels with single front castor for easy manoeuvrability. Supplied with hose reel to keep your workspace tidy. Includes a drain valve for easy release of condensed water build up in the tank. Belt Drive Compressors SAC32055B Heavy-duty 3-phase compressor suitable for the professional workshop. Triple cylinder pump system maximises performance to keep running costs low compared to single stage, single phase models. Pump features heavy-duty full cast cylinders, capped by an alloy heads for improved heat dissipation and long life. Heavy-duty drive guards protect belt and flywheel that is designed to force air over the pump to aid cooling. Includes a drain valve for easy release of condensed water build up in the tank. 5.5hp High Flow Workshop Air Filter/Regulator/Lubricators 200ltr 20.7 Motor Output 3 PHASE Air Displacement Max. Pressure SAC32775B Voltage/ Phase SAC3503B 50ltr 3hp 12.3(347ltr/min) 145psi(10bar) 230V - 1ph SAC3103B 100ltr 3hp 12.3(347ltr/min) 145psi(10bar) 230V - 1ph SAC32055B 200ltr 5.5hp 20.7(585ltr/min) 145psi(10bar) 415V - 3ph SAC32775B 270ltr 7.5hp 29.7(840ltr/min) 145psi(10bar) 415V - 3ph hp 270ltr 29.7 AIR TOOL KIT WITH SAC32775B ONLY AIRKIT A B C D E Port Size Max. Working Pressure Max. Airflow A SA4001 1/2"BSP 145psi B SA4001R 1/2"BSP 145psi C SA4001F 1/2"BSP 145psi D SA4001FR 1/2"BSP 145psi E SA4001L 1/2"BSP 145psi Get the Sealey app on ios & Android Promotion Code: SUM17 s exclude unless stated otherwise 37

13 COMPRESSS Belt Drive Compressors with Cast Cylinders 2hp 10 WITH SAC0502B ONLY AIR TOOL KIT 50ltr 100ltr AIRKIT ltr Suitable for the semi-professional workshop and serious enthusiast. Fitted with a 2hp motor, these units are ideal for use where a stable 13Amp power supply cannot be guaranteed. Pump features full cast cylinders, capped by alloy head for improved heat dissipation and long life. Heavy-duty drive guard protects belt and flywheel that is designed to force air over the pump to aid cooling. Max Pressure: 145psi(10bar) Motor Output Air Displacement Max. Free Air Delivery Wheels Voltage/ Phase SAC0502B 50ltr 2hp 10 (283ltr/min) 7.25 (205ltr/min) 230V - 1ph SAC0102B 100ltr 2hp 10 (283ltr/min) 7.25 (205ltr/min) 230V - 1ph SAC0152B 150ltr 2hp 10 (283ltr/min) 7.25 (205ltr/min) 230V - 1ph Auto Rewind Control Air Hose Reels PU Hoses 10mtr 15mtr Ø8mm Air Hoses with 1/4"BSP Unions 20mtr 30mtr Manufactured in accordance with EN Rubber alloy air hose suitable for garage and bodyshop applications. Fitted with 1/4"BSP female swivel unions. Ø8 mm ID A Length AHC5 5mtr Ø8 mm ID Ø10 mm ID AHC10 10mtr AHC15 15mtr AHC20 20mtr AHC5 5mtr 10mtr 15mtr 20mtr 5pc Air Accessory Kit Controlled, slow rewind which returns the air hose at a safe speed. Hose can be extended and positioned at any length. Auto layering mechanism prevents jamming. Fitted with high quality PU hose. Heavy-duty wall mounting swivel bracket. Contains quality components. Contents: Suction Feed Spray Gun, Blow Gun, Tyre Inflator, Paraffin Gun, Coiled Air Hose with couplings. SA33/S Hose Length Hose Size (ID/OD) A SA821 10mtr Ø8/12mm B SA822 15mtr Ø10/16.5mm C SA823 20mtr Ø10/16.5mm D SA824 30mtr Ø10/16.5mm EXC INC. 38 sealey sealey tools

14 Direct Drive Compressors 6ltr hp 24ltr 2hp ltr 2hp 110V 110V Aluminium cylinder head with cast iron cylinder gives added resistance to wear. Pump head directly coupled to heavy-duty induction motor for reliable and smooth operation. Precision welded receiver tank manufactured to meet Pressure Vessel Directive. Fitted with fully automatic pressure cut-out switch and twin gauges displaying tank and working pressures. Motor Output Air Displacement Max. Free Air Delivery Max. Pressure Voltage/ Phase SAC0610E 6ltr 1hp 4 (113ltr/min) 2.7 (76ltr/min) 116psi (8bar) 230V - 1ph SAC2420E110V 24ltr 2hp 6.3 (178ltr/min) 4.6 (130ltr/min) 116psi (8bar) 110V - 1ph SAC5020E110V 50ltr 2hp 6.3 (178ltr/min) 4.6 (130ltr/min) 116psi (8bar) 110V - 1ph Direct Drive Compressors 24ltr 1.5hp 50ltr 2hp 6 Aluminium head with cast iron cylinder gives added resistance to wear. Suitable for general purpose workshop applications. Pump head directly coupled to heavy-duty induction motor for reliable and quiet operation. Welded tank complies with latest European standards. Fitted with fully automatic pressure cut-out switch and twin gauges displaying tank and working pressures. Fitted with ASTA/BS approved non-rewirable plug. 7 Motor Output Air Displacement Max. Free Air Delivery Max. Pressure Voltage/ Phase SA ltr 1.5hp 6 (170ltr/min) 4.2 (119ltr/min) 116psi (8bar) 230V - 1ph SA ltr 2hp 7 (200ltr/min 4.8 (135ltr/min) 116psi (8bar) 230V - 1ph V-Twin Direct Drive Compressors 50ltr 3hp 100ltr 3hp V-Twin pump with aluminium cylinders and cast iron liners for reduced weight and improved resistance to wear. Suitable for general purpose workshop applications. Pump directly coupled to heavy-duty induction motor for reliable and quiet operation. Precision welded receiver tank manufactured to meet Pressure Vessel Directive. Fitted with fully automatic pressure cut-out switch, air regulator and pressure gauges for tank and supply. Supplied with handle and wheels. Fitted with ASTA/BS approved non-rewirable plug Motor Output Air Displacement Max. Free Air Delivery Max. Pressure Voltage/ Phase SAC ltr 3hp 12.6 (357ltr/min) 8.75 (248ltr/min) 130psi (9bar) 230V - 1ph SAC ltr 3hp 12.7 (360ltr/min) 8.8 (249ltr/min) 130psi (9bar) 230V - 1ph Get the Sealey app on ios & Android Promotion Code: SUM17 s exclude unless stated otherwise 39

15 AIR TOOLS Composite Air Impact Wrenches Twin Hammer B Combination of composite materials, alloyed metals and twin hammer design result in a lightweight, durable and powerful air impact wrench. Soft grip handle with downward facing exhaust make these wrenches comfortable on the hands and ears and limits the circulation of brake dust on wheel applications. Fingertip control of power and direction via lever on rear of wrench. Suitable for professional garage use. Twin Hammer D A Drive Working Torque Max. Torque A GSA6000 3/8"Sq 320lb.ft(435Nm) 370lb.ft(503Nm) B GSA6002 1/2"Sq 490lb.ft(670Nm) 590lb.ft(800Nm) C GSA6004 3/4"Sq 995lb.ft(1350Nm) 1180lb.ft(1600Nm) D GSA6005 1"Sq 1230lb.ft(1670Nm) 1475lb.ft(2000Nm) STYLE OF CASING MAY VARY C Ø75mm Air Palm Orbital Sander Ø150mm Air Palm Sanders Variable speed control lever for quick adjustment to suit workpiece. Supplied with hook-and-loop pad. GSA Air Ratchet Wrenches EXC INC. Thread Size Ø100mm Air Angle Grinder Heavy-Duty Type Ø75mm Air Cut-Off Tool GSA04 5/16"UNF Air Palm Random Orbital Non-Vacuum GSA05 5/16"UNF Dust-Free Air Palm Random Orbital GSA06 5/16"UNF Dust-Free Air Palm Random Orbital Self Contained Contoured and insulated handle - reduces chill and vibration. Heavy-duty twin pawl ratchet mechanism. 60lb.ft Torque output. Low noise exhaust adjusts 360. Four speed, integral air regulator. Drive GSA20 3/8"Sq GSA21 1/2"Sq Aluminium body and bevel gear housing with steel disc-guard and side handle. Fitted with throttle safety device to prevent accidental operation. Balanced and comfortable to operate. Supplied with side handle, grinding disc and locking and pin spanners. SA EXC INC. 0.6hp Air motor with 360 adjustable disc guard. Four-position air regulator. Rotating, adjustable exhaust outlet. Soft grip handle. Throttle safety device prevents accidental operation. Ideal for cutting exhaust brackets. Supplied with Ø75mm cutting disc. GSA EXC INC. 40 sealey sealey tools

16 A Midi C Air Die Grinder Adjustable exhaust outlet for control of exhaust direction. Trigger with safety catch. Supplied with two spanners. Overall Length: 165mm. GSA A EXC INC. B Midi Midi 90 Angle Air Die Grinder Directional, low noise air exhaust can be rotated 360 giving operator added protection. Fitted with safety trigger to prevent inadvertent operation. Supplied with adjustment spanners. GSA Adjustable exhaust outlet for control on exhaust direction. Trigger with safety catch. Supplied with two spanners. Overall Length: 240mm. GSA B EXC INC. Air Die Grinder Long Reach C EXC INC. 15pc Air Die Grinder Kit 42pc Air Angle Die Grinding/Sanding Kit Ø75mm Mini Air Polisher Soft handle grip for comfort and control. Adjustable exhaust outlet for control of exhaust direction. Trigger with safety catch. Supplied with selection of popular grinding points, EXC. two spanners and carry-case. GSA INC. Air Shears Series 90 air angle die grinder ( GSA674). Safety trigger. 360 Rotating exhaust. Includes a range of die grinding points, sanding rolls and Ø50/75mm preparation pads. Replacement components readily available. GSA674K Low Vibration Reciprocating Air Saw EXC INC. Powerful air motor provides smooth operation under-load. Supplied with Ø75mm hook-and-loop pad and spanner. Use with Ø79mm buffing and polishing heads. GSA Ø10mm Air Angle Drill with Keyless Chuck EXC INC. Fingertip operated throttle. Cuts sheet metal up to 1.2mm thick. Built-in muffler. GSA EXC INC. Patented design provides extremely low vibration. Leader hose incorporates an outer sheath, which helps reduce noise levels. Supplied with two blades, four files, hex key and leader hose. GSA EXC INC. 90 Angle is ideal for drilling in hard to reach areas. Supplied with Jacobs keyless chuck for fast bit changes. Directional, low noise air exhaust can be rotated 360. Contoured composite handle reduces effects of chill and vibration. Fitted with safety trigger. GSA EXC INC. Get the Sealey app on ios & Android Promotion Code: SUM17 s exclude unless stated otherwise 41

17 ELECTRIC POWER TOOLS CP6000 SERIES - ONE BATTERY FITS ALL Integral LED work light. Includes 1x CP6011, 1x CP6012, 1x CP6013, 1x CP6014, 2x CP60BP 14.4V 2Ah Lithium-ion batteries and 1x CP60MC battery charger. CP6000COMBO Total Package EXC EXC INC INC. CANVAS BAG WITH CP6000COMBO ONLY CP1200CB KIT INCLUDES 14.4V Cordless Lithium-ion 3/8"Sq Dr Ratchet Wrench 68Nm 4-Pole Motor Body Only Variable speed while producing torque of up to 68Nm (50lb.ft). 14.4V Cordless Lithium-ion 3/8"Sq Dr Impact Wrench 140Nm Body Only Produces torque of up to 140Nm(103lb.ft). 14.4V Cordless Lithium-ion 1/4"Hex Impact Driver 117Nm Body Only Variable speed while producing torque of up to 117Nm (86lb.ft). Small compact design. 14.4V Cordless Lithium-ion 14.4V 10mm 2-Speed Drill/Driver Body Only Features high/low speed selection and 11 torque settings. 10mm Quick release keyless chuck. 14.4V 2Ah Lithium-ion Cordless Power Tool Battery x2 14.4V 40min Lithium-ion Battery Charger for CP60BP Car Polishers 230V Ø170mm Variable Speed Sander/Polisher 1300W Random orbital polishers with two polishing bonnets. Smooth operation provides even buffing/polishing with no hot spots. High impact, durable ABS housing. Supplied with 4mtr cable and BS approved plug. CE approved. 180W Oscillating Multi-Tool 230V Pad Size ER150P Ø150mm 3-ply foam pad ER230P Ø230mm 5-ply foam pad Ø240mm Cordless Polisher 18V 6 Position electronic variable speed control. Speed Range: rpm. Supplied with side handle, backing pad and disc spanner. MS900PS W EXC INC. 180W Suitable for multiple tasks such as sanding, scraping and cutting various materials. Includes sanding discs, backing pad, offset cutting blade and offset scraper. Full range of additional accessories available. Single speed with 180W motor and sealed bearings. SMT PC MULTI-TOOL BLADE SET SMTA EXC INC. Random orbital polisher with Ø240mm foam backing pad and polishing bonnet. Smooth operation provides even buffing/polishing with no hot spots. High impact, durable housing with adjustable soft grip handles. 18V Lithium-ion battery pack and battery charger. Speed: 2500rpm. CP2518L EXC INC. 18V 42 sealey sealey tools

18 26V 1/2"Sq Drive Cordless Lithium-ion Impact Wrench 335lb.ft 26V 450Nm Torque Powerful and compact producing torque in excess of 450Nm(335lb.ft). Powered by a 26V Lithium battery, which retains its charge over long periods of time. Supplied with two hour mains charger. CP EXC INC. CP1200 SERIES - ONE BATTERY FITS ALL CP1200COMBO Total Package : V 1/2"Sq Cordless Impact Wrench 410lb.ft Produces up to 550Nm (410lb.ft) torque. Variable speed switch. Forward and reverse switch. Supplied with 24V 2Ah Ni-MH battery pack and 80 minute mains charger. CP2450MH V 550Nm Torque EXC INC. 24V 2Ah Ni-MH Cordless Power Tool Battery for CP2450MH CP2450MHBP EXC INC. AVAILABLE END OF JUNE KIT INCLUDES 12V 1 Hour Lithium-ion Battery Charger for CP1200BP Recharges CP1200BP 12V lithium-ion battery in 1 hour. LEDs Indicate status of battery from charging to full. Suitable for use with the CP1200 Series. CP1200MC KIT INCLUDES X 2 BATTERIES 12V 3/8"Sq Drive Impact Wrench 80Nm Compact, lightweight cordless impact wrench. Variable speed control trigger with lock function. CP V 1/4"Hex Drive Impact Driver 80Nm Compact, lightweight cordless impact driver. Variable speed control trigger with lock function gives more control during application. CP1203 Ø115mm Angle Grinder 750W Slim Body Cordless Lithium-ion Hammer Drill/Driver 12V Compact, lightweight cordless drill/driver with added hammer function mm keyless chuck. 2 speed settings and 21 torque settings gives control to complete various tasks. CP1201 Ratchet Wrench 12V 3/8"Sq Drive 45Nm Compact, lightweight and robust, ideal for tight spaces. Features a lockable variable speed control trigger. CP W CANVAS TOOL BAG CP1200CB Ø125mm Twin Blade Cut-Off Saw 920W EXC INC. 230V 750W Ø115 X 1.2MM CUTTING DISC 22MM BE PACK OF 5 PTC/115CET Twin Blade Minimising kick-back and sparks for a safer operation. Controlled lubricating feed for maintaining cutting efficiency and cooling blades. Three position rotating handle. Supplied in storage case with ten lubricating sticks. SCT W Features heavy-duty alloy bevel gear head and spindle lock for fast loading/unloading of discs. 750W Motor produces 12000rpm (no load speed). SGS EXC INC EXC INC. Twin blades rotate in opposite directions creating a fast, burr-free, clean cut. Get the Sealey app on ios & Android Promotion Code: SUM17 s exclude unless stated otherwise 43

19 WELDING 130Amp MiniMIG Portable MIG Welder 1W LED ALUMINIUM PENLIGHT LED A 130Amp Maximum performance. Features heavy-duty high output transformer and forced-air cooling to ensure the highest level of performance. Contoured grip, non-live torch ensures a steadier weld bead. Includes mini gas regulator, spool of wire, contact tips 0.6 and 0.8mm and gas cup. Suitable for welding with CO 2, Argon or CO 2 /Argon mix. SUPERMIG Professional MIG Welders with Binzel Euro Torches Excellent continuous performance on car panel thickness material. Forced-Air Cooling System allows high duty cycle. Binzel non-live Euro torch reduces accidental arcing and is comfortable in the hand thus ensuring a steadier weld bead. Welds stainless and aluminium too. Includes industrial gas regulator, contact tips 0.6, 0.8mm and gas cup. SUPERMIG255 Includes industrial twin gauge gas regulator, contact tip 0.8mm and gas cup. SUPERMIG275 includes industrial twin gauge gas regulator, contact tip 0.8mm and gas cup EXC INC. 5 SMD LED + 3W CREE LED LITHIUM-ION RECHARGEABLE INSPECTION PENLIGHT LED Amp Professional MIG Welder 150A 150Amp Maximum performance. Forced Air Cooling System allows high duty cycle. Latest design chassis remains stable when used with medium size industrial gas cylinders. Professional contour grip, heat proof non-live torch ensures no sparks until you press the trigger. Proven wire feed system for trouble-free welding. Welds stainless and aluminium. SUPERMIG EXC INC. 5 SMD LED + 3W CREE LED LITHIUM-ION RECHARGEABLE INSPECTION PENLIGHT LED A 270A SUPERMIG275 Gas Bottle Not Included. SUPERMIG A 200A 230A Duty Cycle Absorbed Power Welding Current Wire SUPERMIG180 56A, 65A, 73A, 145A 5.7kW A 5-15kg SUPERMIG200 62A, 80A, 160A 7.4kW A 5-15kg SUPERMIG230 68A, 88A, 175A 8kW A 5-15kg SUPERMIG255 91A, 118A, 205A 8.7kW A 5-15kg SUPERMIG A, 146A, 255A 12.6kW A 5-15kg sealey sealey tools

20 200Amp TIG/MMA HF AC/DC Inverter Welder TIG FOOT PEDAL POWER CONTROL TIG200HFACDCF A AC/DC Fan-cooled AC/DC power supply for pulse TIG and MMA welding applications. Suitable for welding aluminium, magnesium, stainless steel, steel, copper, nickel and titanium. TIG cycle includes post gas and current down-slope regulation. Features regulated high frequency (HF) push button arc that prevents having to touch the work piece to start, keeping the tip in good condition for longer. Includes connector for foot pedal when more control is required. TIG200HFACDC Welding Pliers MMA EXC INC. Spark Proof Welding Blanket 1800mm x 1300mm 40Amp Plasma Cutter Inverter Inverter power supply fitted with plasma cutter control circuitry. Features digital Amp display and two LEDs on the front panel indicating overload and mains power. Supplied with a 4.6mtr plasma torch, 2mtr earth cable, 2mtr gas hose and regulator. Ideal for cutting steel, stainless steel, galvanised steel, aluminium, copper and brass. Max. Cutting Thickness: 11mm. IP21S Rated. PP40E EXC INC. 40A Max. Cutting Thickness 11mm Oxyacetylene Gas Welding/Cutting Set Spring loaded, fully insulated pliers. Seven Uses for the welder: nozzle/tip cleaner, nozzle/tip remover, wire cutter, flux chipper, long nose pliers. WP EXC INC. Neoprene coated glass fibre blanket tested to BS 476 Pt.1, Pt.7, Pt.20 and UK building regulations Class 0. SSP EXC INC. 4pc Magnetic Quick Clamp Set Magnetic Adjustable Link Holding per Magnet: 4.5kg. Holds any ferrous metal at angles of 45, 90 and 135 giving good versatility to the welder. MQC EXC INC. Allows the application of the exact angle and positioning of metal to be welded. Can be set at any angle by adjustment and locking of wing nut. No need for additional tooling or labour for precise consistent angles. Angle Range: 180. MAL EXC INC. Complete set of regulators and torches for oxyacetylene gas welding. Single stage gas regulators with two gauges to show bottle pressure and working pressure. 4.5mtr Twin gas hose set with check valves (to torch) and EN 730-compliant pressure activated flash arrestors (to regulators). Welding torch with three lightweight nozzles. Cutting torch attachment with three ANMS cutting nozzles. Spark lighter. SGA EXC INC. Get the Sealey app on ios & Android Promotion Code: SUM17 s exclude unless stated otherwise 45