STEERING AND SUSPENSION section 2

Transcription

1 STEERING AND SUSPENSION section TRRT-PC piece Track Rod Removal Tool Kit Quality, kit designed for easy removal and installation of ball joints on track rods. Knurled handle provides extra grip and three interchangeable heads offer complete versatility. Supplied with robust impact resistant plastic carrying box. Track rod arm length 0mm Interchangeable head sizes 0-, -0 and 0-mm 9. P N000 Coil Spring Compressor Kit Quality, suitable for both Macpherson Strut Coil Springs and conical springs. Interchangeable jaws allow the kit to be used on a wide range of vehicles. Safety overload system ensures protection for user while yoke protectors stop the springs from being damaged. Packed in blow mould plastic carrying case with display sleeve. Main body with mm hex. dr. and safety overload pin x gold jaws (0-mm dia.) x black jaws (0-0mm dia.) x silver jaws (-90mm dia.) x pairs of plastic covers x extension bracket with hex key. P N00 Telescopic Spring Compressor Kit Quality; telescopic spring compressor with nonslip, three pronged arm feature for maximum grip. Allows the removal and replacement of coil springs on the suspension without dismantling the axle. Suitable for use on multi-link and independent suspensions (Max load capacity 0kg). Display packed in blow mould case..0 P CODES APPLY TO THESE ITEMS TRRT-A Track Rod Removal Tools Quality, for the easy removal and installation of track rod knuckles. Driving end of /" sq. dr. (inner) and mm hex. (outer). 0mm hollow internal sleeve length/00mm overall length. Handle knurled for extra grip. No. Capacity Qty each -mm. P -mm.9 P OPEN CAGE SLIDE IN COMPRESSOR UNTIL FULLY ENGAGED THE ABOVE DIAGRAMS SHOW COIL SPRING COMPRESSOR (STOCK No. 00) BEING SECURELY PLACED IN SAFETY CAGE (STOCK No. 00) LOCK DOWN CAGE LID TRAT Track Rod Adjusting Tool Quality, for loosening and adjusting stubborn track rods. The solid forged steel head and jaws allow more torque for less effort while the large surface area of the serrated jaws help prevent damage to the track rod. For use on -mm diameter track rods. Overall length mm. Carton packed. 9.9 P 0 N00 00kg Coil Spring Compressor Quality, designed for safe and effective compression of suspension springs to allow removal and replacement of the damper units. Safety overload system to protect user and spring compressor. Supplied with two jaw sets one for small springs size 0-mm and the other for large springs size -9mm. A safety cage is available separately for minimizing the risk when working on suspension systems servicing (Stock No. 00). Display carton. Stock Part Box Price No. No. Description Qty each 00 N00 Compressor.0 P 00 N00 Safety Cage. P

2 STEERING AND SUSPENSION N piece Coil Spring Compressor Set Hooks manufactured from tension ductile iron with galvanized finish. mm diameter carbon steel screws. Maximum opening 90mm. No. Length Qty per set 0mm. D BALL JOINT SEPARATOR KIT N9 Ball Joint Puller Forged body with hardened thrust bolt. Direct action puller with a jaw capacity of 9mm. Suitable for use on most cars and some light commercial vehicles. Display packed. 9. D N piece Coil Spring Compressor Set Wrap round claws with polished chrome finish. Lead screw manufactured from carbon steel hardened and tempered. Jaw design makes them suitable for use in confined areas. Maximum opening 0mm. Display carton.. D N piece Coil Spring Compressor Set Forged carbon steel claws hardened and tempered. Mx.mm screw manufactured from carbon steel hardened, tempered with a chemically blacked finish. Capacity 90-00mm. Carton packed. 9. D HBJS-0 Commercial Vehicle Hydraulic Ball Joint Separator Kit Interchangeable jaws and forged carbon steel body allows ball joint on commercial vehicles to be removed with minimal effort by use of the hydraulic puller. Adjustable jaw opening with maximum opening capacity 9mm. Supplied with instruction manual. Packed in blow mould carrying case with display sleeve. hydraulic ram x manual thrust bolt 9 x 0mm long (approx) x manual thrust bolt 9 x 0mm long (approx) x insert screw bung with mm hex x 0mm jaw x mm jaw x 0mm jaw x main body. P N0 Ball Joint Separator Quality, forged carbon steel body, plated finish with steel bolt. Adjustable jaw opening 9-mm, maximum opening capacity 0mm D /" SQ.DRIVE N piece Coil Spring Compressor Set Cast steel claws with safety hooks to prevent accidental release. Lead screw manufactured from carbon steel hardened and tempered with /" square drive facility. Maximum opening mm. Display carton.. D N0 Stage Ball Joint Separator Quality, two stage design for use on most cars and light commercial vehicles. The off set lever provides excellent performance giving a maximum opening capacity mm. Manufactured from drop forged carbon steel.. D PRODUCT INFORMATION Every effort has been made to ensure that the applications shown in this Draper Tools Catalogue are accurate and include all the current car/van models. When using specialized automotive tools ALWAYS refer to the vehicle manufacturer s service or relevant Haynes manual for detailed and concise instruction of usage. BOX QUANTITY INFORMATION FOR YOUR CONVENIENCE, WE RECOMMEND ORDERING IN BOX QUANTITY OR MULTIPLES OF BOX QUANTITY WHERE SHOWN. YOU CAN STILL ORDER IN ANY QUANTITY UNLESS SPECIFICALLY STATED OTHERWISE 09

3 STEERING AND SUSPENSION section N Fork Type Ball Joint Separator Forged carbon steel body with plated finish, with jaw opening 9mm and throat depth 0mm. 9 00mm. D N Fork Type Ball Joint Separator Forged carbon steel body with plated finish. Jaw opening 9mm and throat depth 0mm. 9 00mm. D CVBT Pneumatic CV Boot Stretcher Quality, innovative labour-saving tool for replacing "stretchy" type CV boots. Fitted with a /" air inlet and operated in conjunction with a standard air line (sold separately). Lightweight construction with simple button control on handle opening the expanding arms to a maximum of 0mm. Suitable for most cars and small commercial vehicles but only in conjunction with "stretchy" style CV boots. Carton packed. Specification: Max: opening capacity... 0mm Max: operating pressure psi (bar) 09. P CVBK piece CV Boot Service Kit Quality, for the correct cutting, tensioning and clamping of the CV joint band. 00mm precision CV boot band cutters for use on CV bands up to mm wide mm CV band cutting tool 0mm CV pliers for tightening ear-type CV bands. Reinforced /" sq. dr. recesses in handle for the use of a breaker bar/ torque wrench where specific torque is required D CVBT-A CV Boot Tool This tool allows the user to renew the CV boot of a vehicle without dismantling the CV joint. Manufactured from nylon with a 9mm hexagon bar fitted to the base. Stock Tool Box Price 0 mm.9 D SUSPENSION ARM LEVER LAL Suspension Arm Lever Quality, for use on suspension arm and hub work maintenance. Soft grip handle with adjustable hook allows easy use on either side of the vehicle. Adjustable fulcrum gives maximum leverage with minimum effort. 0mm. P AIR LINES AND AIR LINE FITTINGS A complete selection of /", /" and /" air lines are available on pages 9-0. This selection includes recoil, whip hoses and straight air lines in a variety of different lengths. Also we supply a wide selection of connectors and fittings on pages -. 0

4 PULLERS section N0 Twin Leg Reversible Pullers Puller with two reversible legs for external and internal pulling of gears, bearings, etc. Legs are forged carbon steel and have long and short reach facility. Yoke and thrust bolt are manufactured from carbon steel. Screw has a rolled thread with chemically blacked finish. 90 mm mm.0 D 90 0mm 0mm 9.0 D 9 mm 0mm. D BRK 9 piece Blind Bearing Removal Kit Quality, for pulling bearings from a blind hole in an engine or transmission case. Saves time and frustration in pulling bearings that are accessible from only one side and cannot be pushed out. Comprises a slide hammer 90mm long and eight expandable split collets size:, 0,,,, 0, and 0mm diameter. Packed in blow mould case with display sleeve P IBP Small Insert Bearing Puller Kit Quality, allows the removal of bearings where normal pullers are unable to be used. It locks into the bearing race itself. Manufactured from hardened and tempered steels chemically blacked for corrosion protection. Suitable for use with ISO bearing sizes: 00-00; 0-0 and Packed in blow moulded case with display sleeve. Puller yoke with centre screw and twin arms x leg extensions Centre screw thread cap x ball ended threaded puller adaptors. P N Triple Leg Reversible Pullers Puller with three reversible legs for external and internal pulling of gears, bearings, etc. Legs are forged carbon steel and have long and short reach facility. Yoke and thrust bolt are manufactured from carbon steel. Screw has a rolled thread with chemically blacked finish. 90 mm mm.0 D 909 0mm 0mm.9 D 99 mm 0mm. D PWPK V-Belt Pulley Wheel Removal Set Quality, for the removal of V-belt pulley wheels. Sculpted grooves on face of puller allow the legs to lock on to outer circumference of the V-belt for easy removal. Display packed in blow mould case with display sleeve. Small straight leg puller: max. reach 0mm; max spread 0mm Large straight leg puller: max. reach mm; max spread 00mm cranked puller legs (can be used with either yoke) 00. P IPB Large Insert Bearing Puller Kit Quality, allows the removal of bearings where normal pullers are unable to be used. It locks into the bearing race itself. Manufactured from hardened and tempered steels chemically blacked for corrosion protection. Suitable for use with ISO bearing sizes: 0-0; 0-0 and 0-0. Packed in blow moulded case with display sleeve. Puller yoke with centre screw and twin arms x threaded leg extensions x ball ended threaded puller adaptors 9.0 P Twin/Triple Reversible Pullers Puller with a two and three leg option for external and internal pulling of gears, bearings, etc. Legs are forged carbon steel and have long and short reach facility. Yoke and thrust bolt are manufactured from carbon steel. Screw has a rolled thread with chemically blacked finish. Supplied with twin and triple yoke that will take either two or three legs. 99 mm 00mm.0 D 0mm 00mm.9 D BSD/SET piece Bearing and Seal Driver Kit Quality, for the positioning of bearings without damage to the bearing or bearing cage. Lightweight and portable, ideal for use on location when servicing vehicles/machinery. Comprises dead blow hammer, three drift sleeves and different-sized drifts to match individual bearings. Packed in blow mould case with display sleeve. 0g dead blow hammer x bearing drift sleeves x drifts sizes from 0-mm to 0-0mm 9. P

5 PULLERS SEE PRODUCT VIDEO BPK Bearing, Seal and Bush Insertion/Extraction Kit Quality, for the accurate and controlled insertion/removal of normal bearings, silent bearings, hydraulic bearings, rubber bearings, bearing bushes, shaft seals etc. Comprises 0 adaptor rings and four fine thread puller bars with hex. nut ends. Packed in blow mould carrying case and display sleeve P AFWPS piece Alternator Pulley Tool Kit Quality, for removing alternators and freewheels. Comprehensive kit can be used on popular european car marques either on or off the engine. Packed in blow mould case with display sleeve. T0 T0 M spline M0 spline H H0 M0 spline bit T0 /" Sq. Dr. with free moving spline collar with mm hex: length mm (approx) M0 spline /" Sq. Dr. with free moving spline collar with mm hex: length mm (approx) M0 spline /" Sq. Dr. length 0mm (approx) M0 spline /" Sq. Dr. with free moving spline collar with mm Hex: length 0mm (approx) mm stepdown to 9mm hollow Hex bolt adapter mm stepdown to mm hollow Hex bolt adapter pin hollow adapter mm Hex mm Hex hollow adapter Spline hollow adapter with mm Hex Spline hollow adapter with mm Hex /" Sq. Dr. with 0mm Hex 9.9 P HPK 0 tonne Hydraulic Puller Kit Six position multi-function puller with adjustable two or three leg function. Allows bearings, gears, etc. to be removed with minimal effort by use of the hydraulic puller. Supplied with instruction manual. Packed in blow mould carrying case with display sleeve. hydraulic pump puller legs nuts and washers link plates / leg puller yoke nose adaptor Min/Max Reach 0-0mm Min/Max Spread 00-0mm 009. P BSD/SET/B piece Bearing and Seal Driver Kit For the installation of bearings and seals. Helps avoid damage to bearing and seal faces. Packed in blow mould case and display sleeve. 9 x aluminium drive flanges size: 0,, 0, 9,,,, and mm mm bore spacer aluminium mandrel drive 0.0 P BSD/SET piece Bearing Positioning Kit Quality, for the positioning of bearings without damage to the bearing or bearing cage. Comprises driver bar and six different-sized composite press blocks to match individual bearings. Packed in blow mould case with display sleeve. Driver bar Press blocks - black and mm dia.; brown and mm dia.; blue and 9mm dia.; green double-sided 0mm dia.; orange double-sided.mm dia.; purple double-sided 9. mm dia P AFWPS piece Alternator Pulley Tool Kit Quality, for removing alternators and freewheels. Comprehensive kit can be used on popular european car marques either on or off the engine. Packed in blow mould case with display sleeve. M0 spline - /" Sq. Dr. T0 TX-star - /" Sq. Dr. for Bosch alternators M0 hex M hex M spline M0 spline T0 TX-STAR T0 TX-STAR /" Sq. Dr. to 0mm female hex adaptor x pulley connectors Four prong connector Hex slider 9. P N Universal Hub Puller Plated ductile body casting with hardened screw for use on four stud wheels. Bolt centres 00-mm. HSHK Hydraulic Ram and Slide Hammer Hub Puller Kit Quality, comprises a ten slot universal hub adaptor plate for simple fitment to any hub bolt layout; a powerful tonne hydraulic ram to remove the hub assembly and a.kg slide hammer for the removal of stubborn hubs where controlled pressure is not required. Display packed in a blow mould case. 0. P 9.0 D BOX QUANTITY INFORMATION FOR YOUR CONVENIENCE, WE RECOMMEND ORDERING IN BOX QUANTITY OR MULTIPLES OF BOX QUANTITY WHERE SHOWN. YOU CAN STILL ORDER IN ANY QUANTITY UNLESS SPECIFICALLY STATED OTHERWISE