COMMERCIAL ITEM DESCRIPTION SPECIFICATION SHEET FUSE, CARTRIDGE, INSTRUMENT TYPE, 5 MM X 20 MM, QUICK-ACTING, LOW-BREAKING CAPACITY
|
|
- Clara Daniel
- 5 years ago
- Views:
Transcription
1 [METRIC] 4 May 2009 SUPERSEDING /2 October 28, 2004 COMMERCIL ITEM DESCRIPTION SPECIFICTION SHEET FUSE, CRTRIDGE, INSTRUMENT TYPE, 5 MM X 20 MM, QUICK-CTING, LOW-REKING CPCITY The General Services dministration has authorized the use of this commercial item description for all federal agencies. The complete requirements for procuring the fuses described herein shall consist of this document and the issue in effect of CLSSIFICTION/PRT OR IDENTIFICTION NUMER (PIN). This commercial item description (CID) specification sheet uses a classification system which is included in the PIN as shown in the following example (see NOTES) / CID number Dash number Configuration (see figure 1) SLIENT CHRCTERISTICS. Interface and physical dimensions. Fuses supplied to this CID specification sheet shall be as specified herein, and shall meet the requirements of NSI/IEC , part 2 (see figure 1). Case or body. The case or body shall be glass. Ferrules. The materials for the ferrules shall be nickel or silver plated brass. Mounting. Configuration (ferrule type) is intended to be used with an applicable fuseholder or fuse clip. Configuration (axial leads) is intended to be directly soldered onto a printed wiring board. Current rating. The ampere rating shall be as specified in table I. Voltage rating. The voltage rating shall be 250 V ac maximum. Voltage drop. Voltage drop shall be in accordance with table I. Pre-arcing time/current characteristic. Pre-arcing time/current characteristic shall be as specified in table II. reaking capacity. The breaking capacity shall be 35 amperes maximum or 10 I n, whichever is greater. Endurance. Endurance shall be 100 cycles at 1.2 times the rated current followed by 1 hour at 1.5 times the rated current. MSC N/ FSC 5920
2 Ltr mm Inches Min Max Min Max C D E F G H NOTES: 1. Dimensions are in millimeters. 2. Tolerance is 0.13 mm (.005 inch), unless otherwise specified. FIGURE 1. Interface and physical dimensions. 2
3 CID dash number Configuration TLE I. Characteristics. Current rating (amperes) Maximum voltage drop (mv) 32 m 10, m 8, m 7, m 5, m 4, m 3, m 2, m 2, m 1, m 1, m 1, m 1, m 1, m m Power dissipation (W) max
4 CID dash number TLE I. Characteristics - Continued. Configuration Current rating (amperes) Maximum voltage drop (mv) Power dissipation (W) max NOTES. Rated current 23 to 100 m inclusive bove 100 m to 6.3 TLE II. Pre-arcing time/current characteristic (+25 C 10 C). Percent of current rating 210 percent 275 percent 400 percent 1000 percent Max. Min. Max. Min. Max. Max. 30 min. 10 ms 500 ms 3 ms 100 ms 20 ms 30 min. 50 ms 2 s 10 ms 300 ms 20 ms PIN. The PIN should be used for Government purposes to buy commercial products to this CID specification sheet. See the classification section for PIN format example. Source of document. Other Publications MERICN NTIONL STNDRDS INSTITUTE/INTERNTIONL ELECTROTECHNICL COMMISSION (NSI/IEC) NSI/IEC Miniature Fuses, Part 2: Cartridge Fuse-Links. 4
5 (Copies of this document are available online at or from the merican National Standards Institute, 25 West 43rd Street, 4th Floor, New York, NY, ) (Industry association specifications and standards are generally available for reference from libraries. They are also distributed among technical groups and using Federal agencies.) Commercial products. s part of the market analysis and research effort, this CID specification sheet was coordinated with the following manufacturers of commercial products. t the time of CID specification sheet preparation and coordination, these manufacturers were known to have commercial products that would meet the requirements of this CID specification sheet. (NOTE: This information should not be considered as a list of approved manufacturers or be used to restrict procurement to only the manufacturers shown.) MFR's CGE MFR's name and address Littelfuse Incorporated 800 E. Northwest Highway Des Plaines, IL Phone number (847) Facsimile number (847) electronics@littelfuse.com URL: el Fuse Incorporated 206 Van Vorst Street Jersey City, NJ Phone number (201) Facsimile number (201) belfuse@belfuse.com URL: 5
6 Part number (P/N) supersession data. These CID specification sheet PINs supersede the following MFR s P/N's as shown. This information is being provided to assist in reducing proliferation in the Government inventory system. CID dash number MFR CGE TLE III. P/N supersession data. MFR s P/N 1/ CID dash MFR s P/N 1/ MFR CGE number MFR CGE MFR CGE N/ SF500-R N/ SFP500-R N/ SF630-R N/ SFP630-R N/ SF800-R N/ SFP800-R N/ SF1-R N/ SFP1-R SF080-R SF1.25-R SFP080-R SFP1.25-R SF100-R SF1.6-R SFP100-R SFP1.6-R SF125-R SF2-R SFP125-R SFP2-R SF160-R SF2.5-R SFP160-R SFP2.5-R SF200-R SF3.15-R SFP200-R SFP3.15-R SF250-R SF4-R SFP250-R SFP4-R SF315-R SF5-R SFP315-R SFP5-R SF400-R SF6.3-R SFP400-R SFP6.3-R 1/ The manufacturer's P/N shall not be used for procurement to the requirements of this CID specification sheet. t the time of preparation of this CID specification sheet, the aforementioned commercial products were reviewed and could be replaced by the CID PIN shown. For actual part marking requirements, see the marking paragraph of
7 CID number supersession data. This CID supersedes Defense Supply Center, Columbus (DSCC) drawing and its dash numbers as shown. CID dash number TLE IV. CID number supersession data. Superseded DSCC drawing number CID dash number Superseded DSCC drawing number Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extensiveness of the changes. 7
8 MILITRY INTERESTS: Custodians: Navy - EC DL - CC CIVIL GENCY COORDINTING CTIVITY: GS - FSS Preparing activity: DL-CC Project NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the SSIST Online database at 8
COMMERCIAL ITEM DESCRIPTION RELAYS, ELECTROMAGNETIC, GENERAL PURPOSE 10 AMPERES, 1-3PDT, AC AND DC COILS, FLANGE MOUNT
INCH-POUND w/amendment 1 1 November 2005 SUPERSEDING A-A-55143/2A 15 October 2000 COMMERCIAL ITEM DESCRIPTION RELAYS, ELECTROMAGNETIC, GENERAL PURPOSE 10 AMPERES, 1-, AC AND DC COILS, FLANGE MOUNT The
More informationCOMMERCIAL ITEM DESCRIPTION RELAYS, ELECTROMAGNETIC, GENERAL PURPOSE 10 AMPERES, 1-3PDT, AC AND DC COILS, SOCKET MOUNT
INCH-POUND A-A-55143/1C 28 February 200 SUPERSEDING A-A-55143/1B 15 October 2000 COMMERCIAL ITEM DESCRIPTION RELAYS, ELECTROMAGNETIC, GENERAL PURPOSE 10 AMPERES, 1-, AC AND DC COILS, SOCKET MOUNT The General
More informationCOMMERCIAL ITEM DESCRIPTION HOSE ASSEMBLY, NONMETALLIC, FIRE FIGHTING, WITH COUPLINGS
INCH-POUND --59226 1 December 2006 SUPERSEDING --59226 18 May 1998 COMMERCIL ITEM DESCRIPTION HOSE SSEMLY, NONMETLLIC, FIRE FIGHTING, WITH COUPLINGS The General Service dministration has authorized the
More informationPERFORMANCE SPECIFICATION SHEET RUBBER, SYNTHETIC, TUBING
INCH-POUND 15 June 2009 SUPERSEDING MIL-R-6855/4 16 February 1987 PERFORMANCE SPECIFICATION SHEET RUBBER, SYNTHETIC, TUBING This specification is approved for use by all Departments and Agencies of the
More informationCOMMERCIAL ITEM DESCRIPTION HOSE AND HOSE ASSEMBLIES, NONMETALLIC SPRAY
[INCH-POUND] A-A-59613 August 16, 2001 SUPERSEDING ZZ-H-521F May 28, 1993 COMMERCIAL ITEM DESCRIPTION HOSE AND HOSE ASSEMBLIES, NONMETALLIC SPRAY The General Services Administration has authorized the
More informationPERFORMANCE SPECIFICATION SHEET SWITCHES, SENSITIVE, SPDT, UNSEALED
INCH-POUND 14 June 2010 SUPERSEDING 22 May 2006 PERFORMANCE SPECIFICATION SHEET SWITCHES, SENSITIVE, SPDT, UNSEALED This specification is approved for use by all Departments and Agencies of the Department
More informationPERFORMANCE SPECIFICATION SHEET SWITCHES, SENSITIVE, 10 AMPERES AND LOW LEVEL, UNSEALED
INCH-POUND 2 January 201 SUPERSEDING 1 May 200 PERFORMANCE SPECIFICATION SHEET SWITCHES, SENSITIVE, AMPERES AND LOW LEVEL, UNSEALED This specification is approved for use by all Departments and Agencies
More informationPERFORMANCE SPECIFICATION SHEET
INCH-POUND MIL-PRF-24236/24E 5 April 2006 SUPERSEDING MIL-PRF-24236/24D 22 January 2001 PERFORMANCE SPECIFICATION SHEET SWITCHES, THERMOSTATIC, (BIMETALLIC), SUBMINIATURE, TYPE I, HERMETICALLY SEALED,
More informationDETAIL SPECIFICATION SHEET SWITCHES, TOGGLE, MINIATURE, LEVER SEAL, PANEL SEAL, FOUR POLE LOGIC LOAD TO 5 AMPERES
INCH-POUND MIL-DTL-83731/1B July 010 SUPERSEDING MIL-S-83731/1A 0 March 1987 DETAIL SPECIFICATI SHEET SWITCHES, TOGGLE, MINIATURE, LEVER SEAL, PANEL SEAL, FOUR POLE LOGIC LOAD TO 5 AMPERES Inactive for
More informationDETAIL SPECIFICATION SHEET CAP INSERT, ASSEMBLY, PRESSURE SEAL, FLARED TUBE FITTING
INCH-POUND Rev 13 7 August 2014 SUPERSEDING w/amendment 1 20 November 2013 DETAIL SPECIFICATION SHEET CAP INSERT, ASSEMBLY, PRESSURE SEAL, FLARED TUBE FITTING This specification is approved for use by
More informationPERFORMANCE SPECIFICATION SHEET
INCH-POUND MIL-PRF-83536/15A 12 July 2004 SUPERSEDING MIL-PRF-83536/15 27 March 1992 PERFORMANCE SPECIFICATION SHEET RELAYS, ELECTROMAGNETIC, ESTABLISHED RELIABILITY, 4PDT, LOW LEVEL TO 10 AMPERES, PERMANENT
More informationDETAIL SPECIFICATION SHEET SLEEVE, SWAGING-WIRE ROPE
INCH-POUND 3 December 2012 SUPERSEDING 30 September 2011 DETAIL SPECIFICATION SHEET SLEEVE, SWAGING-WIRE ROPE This specification is approved for use by all Departments and Agencies of the Department of
More informationMILITARY SPECIFICATION SHEET
INCH-POUND MS21363B 2 July 2007 SUPERSEDING MS21363A(USAF) 2 July 1985 MILITARY SPECIFICATION SHEET COILS, RADIO FREQUENCY, MOLDED, FIXED, MICROMINIATURE, MAGNETICALLY SHIELDED, (FERRITE CORE-FERRITE SLEEVE),
More informationDETAIL SPECIFICATION SHEET NUT, TUBE COUPLING, SHORT
INCH-POUND 16 February 2010 SUPERSEDING AN818 Rev 19 15 June 1994 DETAIL SPECIFICATION SHEET NUT, TUBE COUPLING, SHORT This specification is approved for use by all Departments and Agencies of the Department
More informationPERFORMANCE SPECIFICATION SHEET
INCH-POUND PERFORMANCE SPECIFICATION SHEET MIL-PRF-2886/E 28 Septmebr 206 SUPERSEDING MIL-PRF-2886/D w/amendment 0 May 2005 FILTERS AND CAPACITORS, RADIO FREQUENCY/ELECTROMAGNETIC INTERFERENCE SUPPRESSION,
More informationDETAIL SPECIFICATION SHEET SLEEVE, SWAGING-WIRE ROPE
INCH-POUND 30 September 2011 SUPERSEDING MS51844D 19 April 2007 DETAIL SPECIFICATION SHEET SLEEVE, SWAGING-WIRE ROPE This specification is approved for use by all Departments and Agencies of the Department
More informationDETAIL SPECIFICATION SHEET SWITCHES, ROTARY, SNAP ACTION CLASS 1SR BASE MOUNTED, SIDE CONNECTED
INCH-POUND 6 February 2006 SUPERSEDING MIL-S-15291/3A(SH) 22 July 1991 DETAIL SPECIFICATION SHEET SWITCHES, ROTARY, SNAP ACTION CLASS 1SR BASE MOUNTED, SIDE CONNECTED This specification is approved for
More informationDETAIL SPECIFICATION SHEET
INCH-POUND MIL-DTL-55302/52D 12 September 2012 SUPERSEDING MIL-DTL-55302/52D 17 December 2003 DETAIL SPECIFICATION SHEET CONNECTORS, PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES: RECEPTACLE, STRAIGHT-THRU,
More informationCOMMERCIAL ITEM DESCRIPTION BEARING, BALL, ANNULAR, SINGLE ROW, RADIAL, NON-FILLING SLOT, DIMENSION SERIES 02
METRIC A-A-59584C 15 September 2008 SUPERSEDING A-A-59584B 23 September 2003 COMMERCIAL ITEM DESCRIPTION BEARING, BALL, ANNULAR, SINGLE ROW, RADIAL, NON-FILLING SLOT, DIMENSION SERIES 02 The General Services
More informationCOMMERCIAL ITEM DESCRIPTION BEARING, BALL, ANNULAR, SINGLE ROW, RADIAL, NON-FILLING SLOT, DIMENSION SERIES 03
METRIC A-A-59585C 15 September 2008 SUPERSEDING A-A-59585B 23 September 2003 COMMERCIAL ITEM DESCRIPTION BEARING, BALL, ANNULAR, SINGLE ROW, RADIAL, NON-FILLING SLOT, DIMENSION SERIES 03 The General Services
More informationDETAIL SPECIFICATION SHEET DISK, VALVE. Inactive for new design after 15 October 1998.
INCH-POUND MS29521H 23 September 2015 SUPERSEDING MS29521G 7 April 2009 DETAIL SPECIFICATION SHEET DISK, VALVE Inactive for new design after 15 October 1998. This specification is approved for use by all
More informationDETAIL SPECIFICATION SHEET
METRIC MIL-DTL-38999/31E 12 March 2014 SUPERSEDING MIL-DTL-38999/31D 19 April 2002 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, CIRCULAR, THREADED, PLUG, LANYARD RELEASE, FAIL-SAFE, REMOVABLE CRIMP
More informationDETAIL SPECIFICATION SHEET NUT, TUBE COUPLING, SHORT
INCH-POUND 19 August 2014 SUPERSEDING w/amendment 1 23 January 2013 DETAIL SPECIFICATION SHEET NUT, TUBE COUPLING, SHORT This specification is approved for use by all Departments and Agencies of the Department
More informationDETAIL SPECIFICATION SHEET
INCH-POUND MIL-DTL-24308/24H 8 June 2018 SUPERSEDING MIL-DTL-24308/24H w/amendment 4 8 April 2015 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRIC, RECTANGULAR, NONENVIRONMENTAL, MINIATURE, POLARIZED SHELL,
More informationDETAIL SPECIFICATION SHEET TRANSMITTER, LIQUID QUANTITY, FLOAT TYPE, ENGINE FUEL. Inactive for new design after 28 September 1993.
INCH-POUND MS500040K 17 November 2011 SUPERSEDING MS500040J 1 March 1991 DETAIL SPECIFICATION SHEET TRANSMITTER, LIQUID QUANTITY, FLOAT TYPE, ENGINE FUEL Inactive for new design after 28 September 1993.
More informationPERFORMANCE SPECIFICATION SHEET ADAPTER, CONNECTOR, COAXIAL, RADIO FREQUENCY. (BETWEEN SERIES BNC TO SERIES TNC), CLASS 2, STRAIGHT PLUG
INCH-POUND MIL-PRF-55339/38A 10 January 2005 SUPERSEDING MIL-PRF-55339/38 11 January 1977 PERFORMANCE SPECIFICATION SHEET ADAPTER, CONNECTOR, COAXIAL, RADIO FREQUENCY. (BETWEEN SERIES BNC TO SERIES TNC),
More informationDETAIL SPECIFICATION SHEET
METRIC MIL-DTL-38999/36 30 November 2006 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, CIRCULAR, THREADED, PLUG, LANYARD RELEASE, FAIL-SAFE, REMOVABLE CRIMP CONTACTS, PINS, SHELL SIZE 25, SERIES III,
More informationPERFORMANCE SPECIFICATION SHEET
INCH-POUND MIL-PRF-22710/14F 20 April 2001 SUPERSEDING MIL-S-22710/14E 18 October 1982 PERFORMANCE SPECIFICATION SHEET SWITCHES, CODE INDICATING WHEEL (PRINTED CIRCUIT), (THUMBWHEEEL SWITCH ASSEMBLY, INTEGRAL
More informationPERFORMANCE SPECIFICATION SHEET
INCHPOUND MILPRF39006/31D 21 March 2018 SUPERSEDING MILPRF39006/31C 21 April 2011 PERFORMANCE SPECIFICATION SHEET CAPACITOR, FIXED, ELECTROLYTIC (NONSOLID ELECTROLYTE), TANTALUM (POLARIZED, SINTERED SLUG),
More informationMILITARY SPECIFICATION SHEET CAPACITORS, FIXED, CERAMIC DIELECTRIC (GENERAL PURPOSE), STYLE CK05
INCH-POUND MIL-C-11015/18E 14 May 2001 SUPERSEDING MIL-C-11015/18D 28 September 1970 MILITARY SPECIFICATION SHEET CAPACITORS, FIXED, CERAMIC DIELECTRIC (GENERAL PURPOSE), STYLE CK05 The requirements for
More informationREVISIONS LTR DESCRIPTION DATE APPROVED
REVISIONS LTR DESCRIPTION DTE PPROVED Change CGE code from 037Z3 to 16236 and e-mail address for comments. Removed approved sources requirements. 4 June 2008. bdouni Prepared in accordance with SME Y14.100
More informationPERFORMANCE SPECIFICATION SHEET SWITCHES, SENSITIVE, MOMENTARY, 4 CIRCUIT OR DPDT (10 AMPERES), UNSEALED
INCH-POUND MIL-PRF-8805/77H 19 September, 2000 SUPERSEDING MIL-PRF-8805/77G 3 September 1999 PERFORMANCE SPECIFICATION SHEET SWITCHES, SENSITIVE, MOMENTARY, 4 CIRCUIT OR DPDT (10 AMPERES), UNSEALED This
More informationPERFORMANCE SPECIFICATION SHEET SWITCHES, SENSITIVE, PLUNGER, 10 AMPERES 2PDT AND 7 AMPERES 4PDT, RESILIENT SEAL
INCH-POUND MIL-PRF-8805/100G 6 December 2012 SUPERSEDING MIL-PRF-8805/100F 4 October 2004 PERFORMANCE SPECIFICATION SHEET SWITCHES, SENSITIVE, PLUNGER, 10 AMPERES 2PDT AND 7 AMPERES 4PDT, RESILIENT SEAL
More informationCOMMERCIAL ITEM DESCRIPTION CLAMPS, HOSE
INCH-POUND 7 JUNE 2006 SUPERSEDING A-A-52506B 16 AUGUST 1996 COMMERCIAL ITEM DESCRIPTION CLAMPS, HOSE The General Services Administration has authorized the use of this Commercial Item Description (CID)
More informationDETAIL SPECIFICATION SHEET
INCH-POUND MIL-DTL-24308/36 1 April 2015 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRIC, RECTANGULAR, MINIATURE, COMBINATION INSERT ARRANGEMENT, RECEPTACLE, SOCKET CONTACTS, SHELL SIZE 4, SIZE 20 SIGNAL
More informationThis specification is approved for use by all Departments and Agencies of the Department of Defense.
INCH-POUND MIL-PRF-39014/5F 16 September 1997 SUPERSEDING MIL-C-39014/5E 16 August 1978 PERFORMANCE SPECIFICATION SHEET CAPACITORS, FIXED, CERAMIC DIELECTRIC (GENERAL PURPOSE), ESTABLISHED RELIABILITY,
More informationDETAIL SPECIFICATION SHEET
INCH-POUND MIL-DTL-17361/4B(SH) 19 September 2006 SUPERSEDING MIL-C-17361/4A(SH) 13 March 1995 DETAIL SPECIFICATION SHEET CIRCUIT BREAKERS, AIR, ELECTRIC, INSULATED HOUSING (SHIPBOARD USE) TYPES AQB-A101,
More information[INCH-POUND] A-A December 1999 SUPERSEDING MIL-C-4109F 31 October 1986
[INCH-POUND] 30 December 1999 SUPERSEDING MIL-C-4109F 31 October 1986 COMMERCIAL ITEM DESCRIPTION COUPLING HALVES, QUICK-DISCONNECT The General Services Administration has authorized the use of this commercial
More informationFEDERAL SPECIFICATION ETHER, PETROLEUM; TECHNICAL GRADE. 1.1 Scope. This specification covers technical grade petroleum ether to be used as a solvent.
METRIC 4 May 2015 SUPERSEDING O-E-751C 10 January 2003 FEDERAL SPECIFICATION ETHER, PETROLEUM; TECHNICAL GRADE The General Services Administration has authorized the use of this federal specification by
More informationCOMMERCIAL ITEM DESCRIPTION PINTLE ASSEMBLY, TOWING, MANUAL RELEASE, , AND LBS CAPACITY
[INCH-POUND] July 30, 1996 SUPERSEDING (see 7.5) COMMERCIAL ITEM DESCRIPTION PINTLE ASSEMBLY, TOWING, MANUAL RELEASE, 18 000, 40 000 AND 100 000 LBS CAPACITY The General Services Administration has authorized
More informationMILITARY SPECIFICATION LUBRICATING OIL, VACUUM PUMP, MECHANICAL
INCH-POUND MIL-DTL-83767C 24 September 2007 SUPERSEDING MIL-L-83767B 8 February 1980 MILITARY SPECIFICATION LUBRICATING OIL, VACUUM PUMP, MECHANICAL Reactivated after 24 September 2007 and may be used
More informationFEDERAL SPECIFICATION METHANOL (METHYL ALCOHOL) 1.1 Scope. This specification covers three grades and four unit quantities of methanol.
NOT MEASUREMENT SENSITIVE 19 January 2016 SUPERSEDING O-M-232L 4 January 2006 FEDERAL SPECIFICATION METHANOL (METHYL ALCOHOL) The General Services Administration has authorized the use of this federal
More informationQQ-A-200/1D 23 June 1983 SUPERSEDING QQ-A-200/1C August 20, 1970 FEDERAL SPECIFICATION SHEET
23 June 1983 SUPERSEDING QQ-A-200/1C August 20, 1970 FEDERAL SPECIFICATION SHEET ALUMINUM ALLOY 3003, BAR, ROD, SHAPES, TUBE AND WIRE, EXTRUDED This specification was approved by the Assistant Administrator,
More informationPERFORMANCE SPECIFICATION SHEET
INCH-POUND MIL-PRF-22710/15H 20 April 2001 SUPERSEDING MIL-S-22710/15G 29 March 1985 PERFORMANCE SPECIFICATION SHEET SWITCHES, CODE INDICATING WHEEL (PRINTED CIRCUIT), (THUMBWHEEEL SWITCH ASSEMBLY, SEALED
More informationDETAIL SPECIFICATION SHEET CONNECTORS, PLUG, ELECTRICAL, STRAIGHT, MINIATURE, CLASSES E, F, G AND R
INCH-POUND MS24266P 7 August 2015 SUPERSEDING MS24266N 20 August 2009 DETAIL SPECIFICATION SHEET CONNECTORS, PLUG, ELECTRICAL, STRAIGHT, MINIATURE, CLASSES E, F, G AND R Inactive for new design after 14
More informationThe activity responsible for this QPL is the Defense Supply Center Columbus (DSCC-VQ), Columbus, OH TEST OR QUALIFICATION REFERENCE
S VALIDATED EVERY TWO YEARS 10-Sep-03 SUPERSEDING QPL-23419-43 24-Aug-01 QUALIFIED PRODUCTS LIST OF PRODUCTS QUALIFIED UNDER PERFORMANCE SPECIFI MIL-PRF-23419 FUSE, CARTRIDGE, INSTRUMENT TYPE, GENERAL
More informationDEPARTMENT OF DEFENSE INTERFACE STANDARD
INCH-POUND MIL-STD-1560C 23 January 2017 SUPERSEDING MIL-STD-1560C 11 February 2015 DEPARTMENT OF DEFENSE INTERFACE STANDARD INSERT ARRANGEMENTS FOR MIL-DTL-38999, MIL-DTL-27599, AND SAE-AS29600 SERIES
More informationCOMMERCIAL ITEM DESCRIPTION HOSE ASSEMBLY, NONMETALLIC, FIRE FIGHTING, WITH COUPLINGS
[INCH-POUND] A-A-59226 May 18, 1998 SUPERSEDING ZZ-H-451G January 13, 1984 COMMERCIAL ITEM DESCRIPTION HOSE ASSEMBLY, NONMETALLIC, FIRE FIGHTING, WITH COUPLINGS The General Services Administration has
More informationDETAIL SPECIFICATION SHEET
INCH-POUND MIL-DTL-16377/53C 27 September 2005 SUPERSEDING MIL-DTL-16377/53B(SH) 25 November 1996 DETAIL SPECIFICATION SHEET FIXTURES, INCANDESCENT AND LIGHT EMITTING DIODE (LED), DETAIL LIGHTING, LANTERN,
More informationDETAIL SPECIFICATION SHEET
INCHPOUND MILDTL85052/1C 30 March 2005 SUPERSEDING MILC85052/1B 30 MAY 1984 DETAIL SPECIFICATION SHEET CLAMP, LOOP, TUBE177 PH CRES, 275 o F, FUEL AND PETROLEUM BASED HYDRAULIC FLUID RESISTANT This specification
More informationDETAIL SPECIFICATION SHEET
INCH-POUND 30 June 2014 SUPERSEDING MIL-DTL-16377/53C 27 September 2005 DETAIL SPECIFICATION SHEET FIXTURES, LIGHTING; INCANDESCENT AND LIGHT EMITTING DIODE (LED), DETAIL LIGHTING, LANTERN, HAND, PORTABLE
More informationANNUALLY 12 September 1997 SUPERSEDING QPL-234l May 1997 QUALIFIED PRODUCTS LIST PRODUCTS QUALIFIED UNDER MILITARY SPECIFICATION.
QUALIFICATIONS VALIDATED QPL-234l9-39 ANNUALLY 12 September 1997 SUPERSEDING QPL-234l9-38 5 May 1997 QUALIFIED PRODUCTS LIST OF PRODUCTS QUALIFIED UNDER MILITARY SPECIFICATION MIL-F-234l9 FUSE, CARTRIDGE,
More informationINCH-POUND MIL-DTL-24211D 25 February 2016 SUPERSEDING MIL-DTL-24211C 9 February 2011 DETAIL SPECIFICATION
DETAIL SPECIFICATION INCH-POUND MIL-DTL-24211D 25 February 2016 SUPERSEDING MIL-DTL-24211C 9 February 2011 GASKETS, WAVEGUIDE FLANGE GENERAL SPECIFICATION FOR 1. SCOPE This specification is approved for
More informationQQ-A-250/11F August SUPERSEDING QQ-A-250/GEN. August 27, 1971 FEDERAL SPECIFICATION SHEET ALUMINUM ALLOY 6061, PLATE AND SHEET
August 3 1982 SUPERSEDING QQ-A-250/11E August 27, 1971 FEDERAL SPECIFICATION SHEET ALUMINUM ALLOY 6061, PLATE AND SHEET This specification is approved by the Commissioner, Federal Supply Service, General
More informationDETAIL SPECIFICATION SHEET CONNECTORS, PLUG, ELECTRICAL, STRAIGHT, MINIATURE, CLASSES E, F, G AND R
INCH-POUND MS24266R 1 December 2016 SUPERSEDING MS24266P 7 August 2015 DETAIL SPECIFICATION SHEET CONNECTORS, PLUG, ELECTRICAL, STRAIGHT, MINIATURE, CLASSES E, F, G AND R Inactive for new design after
More informationQQ-W-343F 19 November 1990 (TO SUPERSEDE) QQ-W-343-E November 13, 1981 FEDERAL SPECIFICATION WIRE, ELECTRICAL, COPPER (UNINSULATED)
19 November 1990 (TO SUPERSEDE) QQ-W-343-E November 13, 1981 FEDERAL SPECIFICATION WIRE, ELECTRICAL, COPPER (UNINSULATED) 1. SCOPE AND CLASSIFICATION 1.1 Scope. This specification covers solid, bunch-stranded,
More informationMILITARY SPECIFICATION MICROCIRCUITS, LINEAR, CMOS, ANALOG SWITCH WITH DRIVER, MONOLITHIC SILICON
INCH-POUND 4 February 2004 SUPERSEDING MIL-M-38510/116 16 April 1980 MILITARY SPECIFICATION MICROCIRCUITS, LINEAR, CMOS, ANALOG SWITCH WITH DRIVER, MONOLITHIC SILICON This specification is approved for
More informationDEFENSE LOGISTICS AGENCY LAND AND MARITIME P.O. BOX 3990 COLUMBUS, OH
DEFENSE LOGISTICS AGENCY LAND AND MARITIME P.O. BOX 3990 COLUMBUS, OH 43218-3990 July 26, 2018 MEMORANDUM FOR MILITARY/INDUSTRY DISTRIBUTION SUBJECT: Initial draft of MIL-STD-1560 w/change 2 (see table
More informationThe activity responsible for this QPL is the Defense Supply Center Columbus (DSCC-VQ), Columbus, OH TEST OR QUALIFICATION REFERENCE
S VALIDATED EVERY TWO YEARS 25-May-04 SUPERSEDING QPL-19207-44 18-Mar-03 QUALIFIED PRODUCTS LIST OF PRODUCTS QUALIFIED UNDER PERFORMANCE SPECIFI MIL-PRF-19207 FUSEHOLDERS, EXTRACTOR POST TYPE BLOWN FUSE
More informationMILITARY SPECIFICATION SHEET
m MIL-C-85049/Z6A 30 November 19YLI SUPERSEDING MIL-C-85049/2ti 16 January 1980 MS3419C 10 Ma 19&? MS316fB 10 May 198Z MILITARY SPECIFICATION SHEET CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, NONENVIRONMENTAL,
More informationMILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, BIPOLAR, ADVANCED LOW POWER SCHOTTKY TTL, NAND GATES, MONOLITHIC SILICON
INCH-POUND MIL-M-38510/370A 15 July 2004 SUPERSEDING MIL-M-38510/370(USAF) 18 March 1983 MILITARY SPECIFICATION MICROCIRCUITS, DIGITAL, BIPOLAR, ADVANCED LOW POWER SCHOTTKY TTL, NAND GATES, MONOLITHIC
More informationPERFORMANCE SPECIFICATION SHEET BATTERY, RECHARGEABLE, NICKEL CADMIUM, VENTED, 1.2-VOLT, 13 AMPERE- HOUR, BB-475/A CELL
INCH-POUND 25 FEB 2011 PERFORMANCE SPECIFICATION SHEET BATTERY, RECHARGEABLE, NICKEL CADMIUM, VENTED, 1.2-VOLT, 13 AMPERE- HOUR, BB-475/A CELL This specification is approved for use within Army CECOM Life
More informationDETAIL SPECIFICATION SHEET INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, FLUORINATED ETHYLENE PROPYLENE, NON-CROSSLINKED
INCH-POUND 17 June 1996 SUPERSEDING MIL-I-23053/11B 01 May 1986 DETAIL SPECIFICATION SHEET INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, FLUORINATED ETHYLENE PROPYLENE, NON-CROSSLINKED This specification
More informationDETAIL SPECIFICATION SHEET INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, CROSSLINKED CHLORINATED POLYOLEFIN, FLEXIBLE
INCH-POUND MIL-DTL-23053/1C 17 June 1996 SUPERSEDING MIL-I-23053/1B 01 May 1986 DETAIL SPECIFICATION SHEET INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, CROSSLINKED CHLORINATED POLYOLEFIN, FLEXIBLE
More informationPERFORMANCE SPECIFICATION GREASE, AIRCRAFT, GENERAL PURPOSE, WIDE TEMPERATURE RANGE, NATO CODE G-395
METRIC 24 January 2005 SUPERSEDING MIL-PRF-81322F 21 July 1998 PERFORMANCE SPECIFICATION GREASE, AIRCRAFT, GENERAL PURPOSE, WIDE TEMPERATURE RANGE, NATO CODE G-395 This specification is approved for use
More informationDETAIL SPECIFICATION SHEET COUPLING HALF, HOSE ATTACHMENT, HYDRAULIC, SELF-SEALING, GROUND SUPPORT, QUICK DISCONNECT, TYPE I AND TYPE II
INCH-POUND 08 December 2009 DETAIL SPECIFICATION SHEET COUPLING HALF, HOSE ATTACHMENT, HYDRAULIC, SELF-SEALING, GROUND SUPPORT, QUICK DISCONNECT, TYPE I AND TYPE II This specification is approved for use
More informationW-R-550A June 12, 1975 SUPERSEDING (See 6.4) FEDERAL SPECIFICATION ROD, GROUND (WITH ATTACHMENTS)
June 12, 1975 SUPERSEDING (See 6.4) FEDERAL SPECIFICATION ROD, GROUND (WITH ATTACHMENTS) This specification was approved by the Commissioner, Federal Supply Service, General Services Administration, for
More informationPERFORMANCE SPECIFICATION ACTUATOR, LINEAR, ELECTROMECHANICAL
INCH-POUND PERFORMANCE SPECIFICATION 17 September 2015 SUPERSEDING MIL-A-85046(AS) 7 September 1976 ACTUATOR, LINEAR, ELECTROMECHANICAL This specification is approved for use by the Naval Air Systems Command
More informationDETAIL SPECIFICATION RUBBER, FLUOROSILICONE ELASTOMER, OIL AND FUEL RESISTANT, SHEETS, STRIPS, MOLDED PARTS, AND EXTRUDED SHAPES
INCH-POUND 11 August 2006 SUPERSEDING MIL-R-25988B 12 July 1983 DETAIL SPECIFICATION RUBBER, FLUOROSILICONE ELASTOMER, OIL AND FUEL RESISTANT, SHEETS, STRIPS, MOLDED PARTS, AND EXTRUDED SHAPES Reactivated
More informationPERFORMANCE SPECIFICATION LUBRICATING OIL, JET ENGINE
INCH-POUND 12 December 2014 SUPERSEDING MIL-PRF-6081D w/amendment 1 30 January 2009 PERFORMANCE SPECIFICATION LUBRICATING OIL, JET ENGINE This specification is approved for use by all Departments and Agencies
More informationMILITARY SPECIFICATION SHEET SCREW, CAP, HEXAGON HEAD (FINISHED HEXAGON BOLT), STEEL, CORROSION RESISTING, PASSIVATED, UNC-2A
INCH-POUND MS35307E 25 April 1997 Superseding MS35307D 1 May 1969 MILITARY SPECIFICATION SHEET SCREW, CAP, HEXAGON HEAD (FINISHED HEXAGON BOLT), STEEL, CORROSION RESISTING, PASSIVATED, UNC-2A This specification
More informationDETAIL SPECIFICATION SHEET INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYOLEFIN, FLEXIBLE, CROSSLINKED
INCH-POUND MIL-DTL-23053/5C 17 June 1996 SUPERSEDING MIL-I-23053/5B 01 May 1986 DETAIL SPECIFICATION SHEET INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYOLEFIN, FLEXIBLE, CROSSLINKED This specification
More information5 x 20mm Fuses S500 Series, Fast-Acting, Glass Tube
5 x 20mm Fuses S500 Series, Fast-Acting, Glass Tube Fast-acting, low breaking capacity Optional axial leads available 5 x 20mm physical size Glass tube with silver-plated (32-125mA) and nickel-plated (160mA-10A)
More informationFF-N-836D April 24, 1972 SUPERSEDING (See section 6) FEDERAL SPECIFICATION
April 24, 1972 SUPERSEDING (See section 6) FEDERAL SPECIFICATION NUT: SQUARE, HEXAGON, CAP, SLOTTED, CASTLE, KNURLED, WELDING AND SINGLE BALL SEAT This specification was approved by the Commissioner, Federal
More informationPERFORMANCE SPECIFICATION SHEET BATTERY, STORAGE, AIRCRAFT, MAINTENANCE-FREE, 24-VOLT, 1.5-AMPERE-HOUR
METRIC MIL-PRF-8565/6A (AS) 25 June 2001 SUPERSEDING DOD-B-8565/6(AS) 26 June 1987 PERFORMANCE SPECIFICATION SHEET BATTERY, STORAGE, AIRCRAFT, MAINTENANCE-FREE, 24-VOLT, 1.5-AMPERE-HOUR This specification
More informationStandard Specification for Bearing, Roller, Tapered, Single Row of Rollers (Metric Series) 1
Designation: Standard Specification for Bearing, Roller, Tapered, Single Row of Rollers (Metric Series) 1 This standard is issued under the fixed designation F2591; the number iediately following the designation
More informationr Class 1 - Alloy chain.
&-C-271C 17 July 1986 SUPERSEDING Fed. Spec. RR-C-271B August 28, 1973 (See 6.9) FEDERAL SPECIFICATION CHAINS AND- AITACHtIENTS. WELDED AND WELDLESS This specification is approved by the Commisioner, Office
More informationTNC Series Series C TN 114
TNC Series TNC Series 114 TNC Interface Mating Dimensions (Per MIL-STD-348) TNC Interface Dimensions MALE Inches/Millimeters 3 Minimum Nominal Maximum LTR in. mm in. mm in. mm A.440 11.17 B.314 7.98.315
More informationFEDERAL SPECIFICATION CUTTING FLUIDS: EMULSIFIABLE OILS
NOT MEASUREMENT SENSITIVE 19 August 2005 SUPERSEDING VV-V-846B 16 October 1998 FEDERAL SPECIFICATION CUTTING FLUIDS: EMULSIFIABLE OILS The General Services Administration has authorized the use of this
More informationPERFORMANCE SPECIFICATION CALIBRATING FLUIDS, AIRCRAFT FUEL SYSTEM COMPONENTS
METRIC 20 January 2012 SUPERSEDING MIL-PRF-7024E 1 October 1997 PERFORMANCE SPECIFICATION CALIBRATING FLUIDS, AIRCRAFT FUEL SYSTEM COMPONENTS Comments, suggestions, or questions on this document should
More informationS and SF series Washable miniature toggle switches
S and SF series Washable miniature toggle switches Distinctive features and specifications Sealed Secure assembly of the two case parts Internally sealed bushing Epoxy sealed terminals Process compatible
More informationDownloaded from
December 20, 1989 TO SUPERSEDE W-F-408D 30 March 1984 FEDERAL SPECIFICATION FITTINGS FOR CONDUIT, METAL, RIGID (THICK-WALL AND THIN-WALL (EMT) TYPE) This specification is approved by the Commissioner.
More informationMS17340 N 12 A 1 FINISH AN EXAMPLE OF THE GOVERNMENT DESIGNATION WHICH IDENTIFIES THE COVER OR RECEPTACLE IS SHOWN B MS17343 C 20 FINISH SIZE -1-
QUALIFICATIONS VALIDATED EVERY 24 MONTHS 19-Jul-99 SUPERSEDING QPL-22992-40 31-Mar-98 QUALIFIED PRODUCTS LIST OF PRODUCTS QUALIFIED UNDER MILITARY SPECIFICATI MIL-C-22992 CONNECTOR, PLUGS AND RECEPTACLES,
More informationMIL-STD S 26 JULY 1985
k -. Downloaded from http://www.everyspec.com -- MIL-STD-3-S 6 JULY 985 SUPERSEDING MIL-STD-3(ln 3 MAY 967 part) MILITARY STANDARD FASTENER TEST METHODS METHOD 5, DRIVING RECESS TORQUE QUALITY CONFORMANCE
More informationANNUALLY 29 May 1996 SUPERSEDING QPL October 1995 QUALIFIED PRODUCTS LIST PRODUCTS QUALIFIED UNDER MILITARY SPECIFICATION MIL-C-83503
QUALIFICATIONS VALIDATED ANNUALLY 29 May 1996 SUPERSEDING QPL-83503-30 3 October 1995 QUALIFIED PRODUCTS LIST OF PRODUCTS QUALIFIED UNDER MILITARY SPECIFICATION MIL-C-83503 CONNECTOR, ELECTRICAL, FLAT
More informationDORADO MV DC/DC CONVERTERS 24V Input 12VDC 8A Output
1/4 Brick Dorado MV Series Industry standard pinout and footprint High efficiency: 86% at 12V, 8A; 88% at 12V, 4A Very low common-mode noise for a commercial DC/DC converter Constant switching frequency
More informationFF-H-1819 August 14, 1974 SUPERSEDING (See 6.10) FEDERAL SPECIFICATION HARDWARE, BUILDERS'; AUXILIARY LOCKS
August 14, 1974 SUPERSEDING (See 6.10) FEDERAL SPECIFICATION HARDWARE, BUILDERS'; AUXILIARY LOCKS This specification was approved by the Commissioner, Federal Supply Service, General Services Administration,
More informationMM-L-751H August 13, 1970 SUPERSEDING Int. Fed. Spec. MM-L-00751G(Army-ME) July 3, 1967 and Fed. Spec. MM-L-751C May 20, 1942 FEDERAL SPECIFICATION
MM-L-751H August 13, 1970 SUPERSEDING Int. Fed. Spec. MM-L-00751G(Army-ME) July 3, 1967 and Fed. Spec. MM-L-751C May 20, 1942 FEDERAL SPECIFICATION LUMBER; SOFTWOOD This specification was approved by the
More informationPERFORMANCE SPECIFICATION GREASE, AUTOMOTIVE AND ARTILLERY
NOT MEASUREMENT SENSITIVE w/ 26 September 2012 SUPERSEDING 30 September 2008 PERFORMANCE SPECIFICATION GREASE, AUTOMOTIVE AND ARTILLERY This specification is approved for use by all Departments and Agencies
More informationROLLS-ROYCE CORPORATION (FORMERLY ALLISON ENGINE COMPANY)
Page 1 2010-19-01 ROLLS-ROYCE CORPORATION (FORMERLY ALLISON ENGINE COMPANY) Amendment 39-16429 Docket No. FAA-2009-0811; Directorate Identifier 2008-NE-41-AD PREAMBLE Effective Date (a) This airworthiness
More informationSM1206 Series. Overload Interrupt Time (Second) Nominal Rating - Note 2. Cold Resistance (Ohm) Note 1. Maximum I 2 T (Ampere 2 Second) Nominal Rating
SM1206 Series Part Numbering System SM1206-32 - 1.0 Fuse Type Voltage Amp Part Number/Rating Cold Resistance (Ohm) Note 1 Overload Interrupt Time (Second) Nominal Rating - Note 2 Maximum I 2 T (Ampere
More informationDETAIL SPECIFICATION DETECTOR PAD, FREE WATER. This specification is approved for use by all Departments and Agencies of the Department of Defense.
METRIC DETAIL SPECIFICATION DETECTOR PAD, FREE WATER 31 March 2006 SUPERSEDING MIL-D-81248B 30 June 1980 This specification is approved for use by all Departments and Agencies of the Department of Defense.
More information*See Part Number System for Details SPECIFICATIONS. Case Dimensions Type Case Size P 2 NFCC04
FETURES RECTNGULR PCKGE ITH METL STRIP FUSE ELEMENT EI SIZES 42, 63, 85 ND 126 CURRENT RTINGS FROM.2 ~ 5. MPS SFETY STNDRD PPROVL (UL and c-ul File Number E32168) Pb-FREE COMPTILE ITH FLO ND REFLO SOLDERING
More informationCOMMERCIAL ITEM DESCRIPTION COUPLING HALVES, QUICK-DISCONNECT, CAM-LOCKING TYPE
COMMERCIAL ITEM DESCRIPTION INCH-POUND May 1, 2003 SUPERSEDING A-A-59326 September 25, 1998 COUPLING HALVES, QUICK-DISCONNECT, CAM-LOCKING TYPE The General Services Administration has authorized the use
More informationFuse Blocks and Clips
PGE Fuse and lock s OMNI-LOK Fuse lock...................................................................................... 484-486 Midget Fuse....................................................................................................
More informationÚÄÄÄÄÄÄÄÄÄÄ ÚÄÄÄÄÄÄÄÄÄÄ ³ METRIC ³ ÀÄÄÄÄÄÄÄÄÄÄÙ TT-T-306E May 28, 1993 SUPERSEDING TT-T-306D December 31, 1992 FEDERAL SPECIFICATION
ÚÄÄÄÄÄÄÄÄÄÄ ÚÄÄÄÄÄÄÄÄÄÄ ³ METRIC ³ ÀÄÄÄÄÄÄÄÄÄÄÙ May 28, 1993 SUPERSEDING TT-T-306D December 31, 1992 FEDERAL SPECIFICATION THINNER, SYNTHETIC RESIN ENAMELS This specification has been approved by the Commissioner,
More informationPERFORMANCE SPECIFICATION COOLERS, LUBRICATING OIL, AIRCRAFT, GENERAL SPECIFICATION FOR
INCH-POUND 06 May 2013 SUPERSEDING MIL-PRF-25478C 29 December 1997 PERFORMANCE SPECIFICATION COOLERS, LUBRICATING OIL, AIRCRAFT, GENERAL SPECIFICATION FOR This specification is approved for use by all
More information(CWR11 Style) Overview. Tantalum Surface Mount Capacitors High Reliability T493 Commercial Off-The-Shelf (COTS) MnO 2
T493 Commercial Off-The-Shelf (COTS) MnO 2 Overview The KEMET T493 is designed for the commercial offthe-shelf (COTS) requirements of military and aerospace applications. The T493 is a surface mount product,
More informationCOMMERCIAL ITEM DESCRIPTION ZIPPERS (FASTENERS, SLIDE INTERLOCKING)
INCH-POUND A-A-55634A 23 MARCH 2004 SUPERSEDES A-A-55634 20 MARCH 1998 COMMERCIAL ITEM DESCRIPTION ZIPPERS (FASTENERS, SLIDE INTERLOCKING) The General Services Administration has authorized the use of
More informationElectric vehicle auxiliary fuses 500 Vdc, A
Supersedes February 2017 BUSSMANN SERIES 500 Vdc, 20-50 A Agency information Designed to: JASO D622 ISO 8820-8 Manufactured under a TS16949 quality system for compliance with automotive requirements RoHS
More information