Tension Cords. HPL high performance cords: the cord cross section is increased compared with standard. This results in a lower belt

Transcription

1

2 ELATECH M and V The timing elts manufactured y ELATECH have een designed to comply with every need of the design engineer in linear motion, power transmission and in conveying applications where precise synchronisation is needed. ELATECH timing elts are manufactured with the ody in thermoplastic polyurethane with excellent wear resistance and with high tensile strength steel cords. A special polyamide faric on the tooth (on request) reduces the coefficient of friction, improves the tooth engagement and reduces noise. Tension Cords In order to maximize the application of ELATECH timing elts, construction with special cords is availale on request: Standard Cord HfE Cord HPL Cord Standard elt HPL high performance cords: the cord cross section is increased compared with standard. This results in a lower elt elongation and more precise positioning accuracy. HfE high Flexiility cords: the cord cross section is spread on a higher numer of single filaments. This results in a lower ending stress and therefore in a higher resistance at reverse ending of the cords. They allow using pulleys and idlers up to 30 smaller in diameter compared to standard. INoX stainless steel cords are suitale for application in aggressive environments. They have lower tensile strength than standard cords. Belt with Polyamide faric on teeth PAZ ArAMID: increases elt flexiility and decreases elt weight. Product declaration - ELATECH elts are certified to e according RoHS 2011//UE - On request, it is possile to deliver elts: with antistatic properties according to ISO93 other special certifications availale on request Colour The standard colour ELATECH timing elt is white. On demand it is possile to deliver elts in different colours. Polyurethane elts It is to e noted that steel cords offer the est technical performances and dimensional staility of the elts. Belt length tolerances are valid for steel cord reinforcement. In case of other material (aramid, fireglass) length tolerance may change. For application with special cords ask our engineering department. Mechanical properties: Excellent dimensional staility High arasion resistance Low pretension and shaft load Maintenance free High linear and angular positioning precision High efficiency Chemical properties: High resistance to: Hydrolysis Ozone UVA Ageing Oils, greases and fats Gasoline Good resistance to acids Working temperatures range for standard material - C +80 C (peaks up to 1 C). For very low temperature special compound material is availale on request (see dedicated tale) Silicon free production

3 Executions ELATECH M They are manufactured in rolls with standard length of 0 m. On request longer or shorter lengths are availale. Main applications are linear drives. ordering example roll 0 m profile T : ordering example profile H cut to length: ELATECH M and V ELATECH R - Roll 0 m r 02 T A / Z ELATECH M cut to length M 0 H A 000 / Z ELATECH timing elt type R ELATECH timing elt type M Width 2 mm (3 digits) Width (x 0,2 = mm) - 3 digits Profile T Pitch mm A= steel cords F= high flexility cords Profile H A= stainless steel cords F= high flexility cords Length 00 mm ( digits) Z= faric on teeth (PAZ) R= faric on ack (PAR) D= faric on PAZ + PAR Z= faric on teeth (PAZ) R= faric on ack (PAR) D= faric on PAZ + PAR ELATECH V They are jointed elts manufactured from open-end ELATECH elts.thanks to the specific manufacturing process, any length may e otained tooth y tooth. Free cominations with special acking materials and welded profiles, make ELATECH V elts ideal in synchronized conveying and highly specialised applications. ordering example profile AT : ordering example profile XL : ELATECH V jointed V 020 AT A 03 / Z ELATECH V jointed V XL A 0070 / Z ELATECH timing elt type V jointed ELATECH timing elt type V jointed Width 20 mm (3 digits) Width (x 0,2 = mm) - 3 digits Profile AT - Pitch mm Profile XL A= stainless steel cords F= high flexility cords A= stainless steel cords F= high flexility cords Length 3 mm ( digits) Length 70 mm ( digits) Z= faric on teeth (PAZ) R= faric on ack (PAR) D= faric on PAZ + PAR Z= faric on teeth (PAZ) R= faric on ack (PAR) D= faric on PAZ + PAR Polyurethane elts 11

4 0 TK 1,2 2,2 Polyurethane self tracking timing elt with steel tension cords Profile T with central guide - x mm Central guide height,0 mm Allow to use pulleys without flanges The central guide is notched in order to maximize elt flexiility Ideal for conveying applications where a side load is generated y Width tolerance: Length tolerance: ±0, ±0, [mm/m] Allowale Allowale TK , , , ,20 F Tzul flexiility Type of cord Minimum pulley numer of teeth animum idler diameter STANDArD Drive without reverse ending z 1 min Drive with reverse ending Flat idler running on elt teeth 0 mm 1 Flat idler running on elt ack 0 mm 80 Polyurethane elts

5 0 13 2, Allowale,, TK - 8, 8, Allowale , , , , ,80 2,, Polyurethane self track timing elt with steel tension cords Profile T with central guide - x, Profile T with central guide - x,0 Central guide height, mm Allow to use pulleys without flanges The central guide is notched in order to maximize elt flexiility Ideal for conveying applications where a side load is generated y Width tolerance: Length tolerance: TK ±0, ±0, [mm/m] SyNCHroNoUS BELT ELATECH - CHD M and V mm width availale only in execution flexiility guide Minimum pulley numer of teeth animum idler diameter Drive without reverse ending 1 1 Drive with reverse ending Flat idler running on elt teeth 0 mm 80 mm Flat idler running on elt ack 0 mm 0 mm Polyurethane elts 81

6 0 ATK 1,2 2,7, Polyurethane self track timing elt with steel tension cords Profile AT with central guide - x mm Central guide height,0 mm Allow to use pulleys without flanges The central guide is notched in order to maximize elt flexiility Ideal for conveying applications where a side load is generated y Width tolerance: Length tolerance: ±0, ±0, [mm/m] Allowale Allowale ,11 ATK , , ,38 F Tzul flexiility Type of cord Minimum pulley numer of teeth animum idler diameter STANDArD Drive without reverse ending z 2 min Drive with reverse ending Flat idler running on elt teeth 0 mm 2 Flat idler running on elt ack 80 mm 82 Polyurethane elts

7 0 13 2, Allowale,, ATK - 8, 8, Allowale , , , , ,08 2,, Polyurethane self track timing elt with steel tension cords Profile AT with central guide - x, mm Profile AT with central guide - x mm Central guide height, mm Allow to use pulleys without flanges The central guide is notched in order to maximize elt flexiility Ideal for conveying applications where a side load is generated y Width tolerance: Length tolerance: ATK ±0, ±0, [mm/m] SyNCHroNoUS BELT ELATECH - CHD M and V mm width availale only in execution flexiility guide Minimum pulley numer of teeth animum idler diameter Drive without reverse ending 1 17 Drive with reverse ending Flat idler running on elt teeth 0 mm 0 mm 2 2 Flat idler running on elt ack 120 mm 120 mm Polyurethane elts 83