Electronic lubrication control unit

Transcription

1 Quickguide instructions Electronic lubrication control unit odel 807 Date of issue arch 08 Form number 07 Version

2 Controller 807 is a universal electronic control unit compatible with dual line, single line parallel and progressive lubrication systems. Compact size and monitoring capabilities allow for controller to be used in both mobile and industrial applications. Quickguide deines digital and audio features available on control unit and includes wiring diagrams for reference. For complete instructional manual, visit: Quickguide is not meant to be alternative to instructional manual, but rather description of key features for someone with lubrication experience. Owner/operator should be familiar with electrical equipment before operating. WARNING Never weld on machine while main switch is ON. Ensure main switch is OFF and correctly tagged. Welding on machine can cause serious damage to controller. Do not alter or modify any part of controller. Do not mount controller near area with excessive heat. Always use speciied fuse rating for controller. Never exceed voltage rating of controller. Never expose controller to direct sunlight. Never expose controller to water or other substances. Speciications Voltage Current drain Pump output Lamp output Switching Fuse Connection Communications Dimensions Weight Protection Temperature range 0 V DC to 0 V DC 0ma maximum (no load) 70ma nominal 7A rms. maximum A maximum Solid state short circuit protected 8 Amp fast blow 0mm glass way OLEX INIFIT JR RS Type 70mm X mm X 8mm (including mounting bracket) 00g IP F to F ( C to 0 C)

3 Keypad layout Fig. Enter button Run/Pause Setup indicator ounting bracket LED display Cycle indicator 7 Second indicator 8 inute indicator 9 Hour indicator 0 Select value down or silent buzzer Blown fuse indicator Fuse holder 8A Power positive/negative Ignition input/aux power output positive Sensor positive/negative Sensor positive/negative 7 External lamp 8 Reservoir sensor connection 9 Pump motor positive/negative 0 RS connection RS connection Reservoir low level status indicator Sensor status indicator Sensor status indicator Pump status indicator Pump status indicator Signal Steady green Flashing green Steady red Pump is not running. Pump is running. Pump is faulty.

4 Panel description SLS Single line system PLS Progressive line system dls Dual line system no Normally open (sensors) nc Normally closed (sensors) LS External lamp steady (continuous supply) LF External lamp lashing (pulsed supply) nfe Non fatal error (pump continues on low level fault) r Run time in cycles, seconds, minutes or hours P F U Pause time in seconds, minutes or hours Fault time in seconds, minutes or hours Vent time in seconds, minutes or hours rcc Run cycle counter YES Conirms program changes tst Test mode for checking installed devices t FE no Stb Time out or dwell time for sensors Fatal errors (pump stops on low level fault) Do not accept program changes Standby mode Fig. Progressive system wiring diagram without prox sensor RES P P V V Ignition otor

5 Fig. Progressive system wiring diagram with one prox sensor and external warning lamp RES P P V V External warning lamp Low level sensor otor Power switch Power supply Proxy Fig. Single line system wiring diagram with pressure switch RES P P V V External warning lamp Low level sensor otor Power switch Power supply Pressure switch

6 Dual line system wiring diagram with pressure switches and hydraulic change over valve Fig. RES P P V V External warning lamp Low level sensor otor Power switch Power supply Pressure switch 7 Pressure switch 7 Fig. Dual line system wiring diagram with / cycles and hydraulic change over valve RES P P V V External warning lamp Low level sensor otor Power switch Power supply icro switch

7 Fig. 7 Fault identiication Press RUN/PAUSE to reset faults. Fault indication counts up from seconds to minutes to hours indicating how long fault has been active. Press down button to silence buzzer. Blown fuse indication. Replace with 8A fuse. Change fuse here. Replace with 8A fuse. Low level fault possible cause, reservoir empty. 7 Proxy fault either blockage in system or faulty sensor. 8 Pump faulty either short circuit or wires have come off. 7

8 Warranty The instructions do not contain any information on the warranty. This can be found in the General Conditions of Sales, available at: or skf.com lincolnindustrial.com SKF and Lincoln are registered trademarks of the SKF Group. SKF Group 08 The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein. arch 08 Form 07 Version