Parts Manual. Manufacturing, Inc. P.O. Box 5060 Salina, Kansas Table of Contents Index (YELLOW) MF30, MF40 & MF45 Manual Fold Sprayer Boom

Transcription

1 (YELLOW) Parts Manual MF30, MF40 & MF45 Manual Fold Sprayer Boom Manufacturing, Inc. P.O. Box 5060 Salina, Kansas ! Read the Operator s manual entirely. When you see this symbol, the subsequent in structions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Cover illustration may show optional equipment not supplied with standard unit. Copyright 2000 Printed 6/12/2003 1)APPLICATION SYSTEMS/BOOMS/MANUAL FOLD BOOMS P Rev. A

2 Section 1 Introduction Section 1 Introduction Table of Contents Index Table of Contents Section 1 Introduction General Information Revisions Touch-up Paint and Manual Information Replacement Hardware Part Number Service Coding Part Number Index Section 2 Booms Boom Frame Assembly Point Sprayer Fixed Boom Mount (S/N 3541+) Point Sprayer Fold Bracket Assembly (S/N 3540-) Point Sprayer Parking Stand Point Carrier Assembly Point Parking Stand Assembly Rear Fold Latch for Trailer Sprayers Slow Moving Vehicle Decal Mounting Assembly Section 3 Spray Kits MF30 Nozzle Assembly 15" Spacing MF30 Nozzle Assembly 20" Spacing MF30 Nozzle Assembly 30" Spacing MF40 Nozzle Assembly 15" Spacing MF40 Nozzle Assembly 20" Spacing MF40 Nozzle Assembly 30" Spacing MF45 Nozzle Assembly 15" Spacing MF45 Nozzle Assembly 20" Spacing MF45 Nozzle Assembly 30" Spacing Section 4 Valves Spraying Systems Check Valve Assembly Precision Check Valve Assembly Nozzle Assembly Section 5 Decals Decal Placement Section 6 Options Calibration Kit Copyright 2000 All rights Reserved Great Plains Manufacturing, Inc. provides this publication as is without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. The illustrations in this manual are not intended for safe and proper assembly or disassembly of equipment. The illustrations are intended for ordering parts only. Great Plains Manufacturing, Incorporated Trademarks The following are trademarks of : Application Systems, Ausherman, Land Pride, Great Plains All other brands and product names are trademarks or registered trademarks of their respective holders. Printed in the United States of America. 7/1/2000

3 Section 1 Introduction Table of Contents Index Section 1 Introduction Section Number & Description Serial Number Break Illustration Page Parts Page Illustration Heading Section 2 Frames Tongue & Pull Bar (S/N ) Tongue & Pull Bar (S/N ) H 13' END WHEEL TONGUE WELDMENT Section 2 Frames H PULL BAR WELDMENT LH H PULL BAR WELDMENT RH C U-BOLT 5/8-11 X 3 17/32 UNEVEN Parts List C WASHER LOCK SPRING 5/8 PLT C NUT HEX 5/8-11 PLT C RHSNB 1/2-13X1 GR C HFSS 1/2-13X1 1/4 GR C WASHER LOCK SPRING 1/2 PLT Illustration C NUT HEX 1/2-13 PLT D SAFETY CHAIN WASHER C SPRING HOSE LOOP C SCREW HEX 3/8-16X1 TYPE F C WASHER LOCK SPRING 3/8 PLT C WASHER FLAT 3/8 SAE PLT D CLEVIS HITCH TOP HALF D CLEVIS HITCH BOTTOM HALF C RHSNB 3/4-10X2 1/2 GR C WASHER LOCK SPRING 3/4 PLT C NUT HEX 3/4-10 PLT C NUT HEX WHIZ 1/2-13 PLT C U-BOLT 1/2-13 X 3 17/32 X4 3/ C SCREW JACK 2000# C RHSNB 3/4-10X3 GR C SAFETY CHAIN LB Illustration Number EWD13 13 End Wheel Drill P 5/21/98 7/1/98 EWD13 13 End Wheel Drill P 2-2 Left Page Number Manual Name & Number New or Modification Date Right Page Number General Information Revisions Please refer to the date at the bottom of each page for the most current version of the equipment. Serial number breaks are at the top of the page at the end of the illustration heading, refer to the illustration above. Touch-up Paint and Manual Information Repaint parts where paint is worn or scratched to prevent rust. Aerosol touch-up paint is available. To order use Great Plains part numbers below: GP Green C GP Black C GP Beige C GP Buckskin C LP Beige C LP Black C Replacement manuals available. Use Great Plains part P. Replacement Hardware All bolts and nuts are grade 5 unless otherwise noted. The use of improper grades of hardware can result in personal injury, damage to equipment, or loss of property. See Hardware Legend on page 1-2, for hardware abbreviations used within all parts lists. 7/1/

4 Section 1 Introduction Table of Contents Index Hardware Legend AR As Required BLADE Blade Bolt C Cap Screw CP Cotter Pin CPHSSS Cup Point Hex Socket Set Screw CPSHSS Cup Point Square Head Set Screw CPSQHSS Cup Point Square Head Set Screw CRFCHMS Cross Recess Flat Countersunk Head Mach. Screw CRPHMS Cross Recess Pan Head Machine Screw CRPHTFS Cross Recess Pan Head Thread Forming CRRHMS Cross Recess Round Head Machine Screw CRTHMS Cross Recess Truss Head Machine Screw CSNB Countersunk Square Neck Bolt FHMS Flat Head Machine Screw FTC Full Thread Cap Screw H Hex Nut HCLN Hex Center Lock Nut HFLCS Hex Flange Lock Cap Screw HFS Hex Flange Screw HFSLN Hex Flange Serrated Lock Nut HFSS Hex Flange Serrated Screw HHCS Hex Head Cap Screw or Metric Bolt HSBHCS Hex Socket Button Head Cap Screw HSFCHCS Hex Socket Flat Countersunk Head Cap Screw HSHCS Hex Socket Head Cap Screw HSSS Hex Socket Head Screw HTLN Hex Top Lock Nut HWHCS Hex Washer Head Cap Screw HWHMS HXBHCS J JIC L LUG NFC NPSM NPTF P PHMS PLOW RHMS RHSNB SCREW LEVELING SCREW THUMB SCREW WELD SFCHMS SFHMS SP SP SCREW SQHSS SRHMS SSS STCS STHMS WHEEL WING Hex Washer Head Machine Screw Hex Socket Button Head Cap Screw Hex Jam Nut 37 Degree Tapered Thread Helical Spring Lock Washer Lug Bolt National Fine Cap Screw National Pipe Straight Mechanical National Pipe Taper Fuel Wide Plain Washer Pan Head Machine Screw Plow Bolt Round Head Machine Screw Round Head Square Neck Bolt Leveling Screw Thumb Screw Weld Screw Slotted Flat Countersunk Head Machine Screw Slotted Fillister Head Machine Screw Special Special Screw Square Head Set Screw Slotted Round Head Machine Screw Socket Set Screw Self Tapping Cap Screw Slotted Truss Head Machine Screw Wheel Studs and Hub Long Bolts Wing Bolt Part Number Service Coding Within the following parts lists some part numbers are coded for revisions and interchangeability. Legend: Newest serial numbers are listed first. Bold face type indicates parts that are serviced. These parts are considered interchangeable, if it supersedes another part, unless otherwise noted. Example: (S/N ) (S/N ) (S/N ) Includes serial numbers and above (to the newest numbers) Includes serial numbers between and including and Includes serial numbers10000 and below (to the oldest number) ➊ First revision, e.g.; ➋ is 2nd revision, ➌ is 3rd revision, etc. (Greater numbers are the newest.) The existing stock for this part should be used up before ordering the new part. Not interchangeable ➀➋ Revision 2 is not interchangeable w/1 Not interchangeable with revision 1 Item # Revision 3 Part Number Description 1. ➀➌ A BLADE SPINDLE W/KEY 1/4SQ X7/8 Revision 2 ➋ D BLD SPNDL SHFT (RPBY A) ➊ D BLD SPNDL SHFT (RPBY A) Use up existing stock. Revision /1/2000

5 Part Number In- Table of Contents Index Section 1 Introduction Part Number Index Part Number aaaaaaaaapage Part Number aaaaaaaaapage Part Number aaaaaaaaapage Part Number aaaaaaaaapage D NYB D A H H D D H H H H H D D D D H D D D D H H H H H H H H H H H H H H S S D D D D D D D H H H H H H H H H H H H H V H D D D D D D D D D D D D D D D D D D D D D A A A A A A A D A A A A A A A A A A A A A A A A A A V V V V V V V V V V V V V V V V V V H C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C /12/

6 Section 1 Introduction Table of Contents Index Part Number Index Part Number aaaaaaaaapage Part Number aaaaaaaaapage Part Number aaaaaaaaapage Part Number aaaaaaaaapage C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C R R R R R R R R R CP21953-EPR CP21953-VI /12/2003

7 Table of Contents Index Section 1 Introduction Part Number Index Part Number aaaaaaaaapage Part Number aaaaaaaaapage Part Number aaaaaaaaapage Part Number aaaaaaaaapage 6/12/

8 Section 2Section 2 Booms Section 2 Booms Boom Frame Assembly Table of Contents Index

9 Boom Frame Assembly Table of Contents Index Section 2 Booms Ref. Part No. Part Description Comments H BOOM FRAME CENTER WELD H BOOM FRAME INSIDE 30' WELD For 30 and 40 booms H BOOM FRAME OUTSIDE 30' WELD H BOOM FRAME INSIDE 45' WELD H BOOM FRAME OUTSIDE 40' WELD For 40 and 45 booms H SWING TUBE WELDMENT H BOOM ELEV SWING BAR WELD H SWING GREASE PIN WELDMENT C RHSNB 3/8-16X1 GR C NUT HEX FLANGE 5/16-18 PLT H BOOM ELEV SWING PIN WELD H SWING PIN WELDMENT H SPRING NUT WELDMENT D SPRING COMP 2 3/8 OD X 6 LG H BOOM HINGE T - WELDMENT C GREASE ZERK STRAIGHT 1/ H BOOM HINGE SWIVEL WELDMENT D ROD - PIVOT C NUT HEX 1-8 NYLON INSERT PLT C HHCS 3/8-16X1 3/4 GR C NUT HEX FLANGE 3/8-16 PLT C HHCS 3/8-16X3 GR C WASHER FLAT 3/8 HARD ASTMF D SLEEVE - WING FOLD C PIN LYNCH 1/4 X 1 3/4 PLT H RING WELD C SP P.H. FLAT HD 1/4-20X2 1/ C NUT HEX LOCK 1/4-20 FLG D BLOCK - NYLON SLIDE C PIN CLEVIS 3/8 X 3 1/4 PLT C PIN HAIR COTTER D LOOP - SKID C HHSC 5/16-18X3 GR C HHCS 1/2-13X1 3/4 GR D TUBE - CENTER BOOM 36. ➋ H CENTER NOZZLE BRACKET WELD 36 ➊ H CENTER NOZZLE BRACKET WELD RH D PAINTED CHANNEL - BACKUP C HHCS 1/2-13X3 GR5 Tandem Axle & 3-Point Sprayer C HHCS 1/2-13X1 1/4 GR5 3-Point Tank Sprayers C CAP - 1 1/2 TUBE H FOLD POST WELD D PLATE - FOLD POST BACK C HHCS 5/16-18X2 1/2 GR C WASHER FLAT 1/2 HARD ASTMF C NUT HEX FLANGE 1/2-13 GR G PLT C PIN CLEVIS 3/8 X 1 57/64 USBLG C CAP - 1 1/4 TUBE C BEARING 3/4 ID X 7/8 OD D TUBE - 5/8 OD X.120 WL X 3/ C HHCS 3/8-16X2 1/2 GR C HHCS 3/8-16X2 3/4 GR D PLATE - RING MOUNTING STRAP C HHCS 3/8-16X2 1/4 GR S SWING TUBE ASSEMBLY Includes items 6, 16 and S BOOM CENTER FRAME ASSEMBLY Includes items 1 and 47. Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 7/1/

10 3-Point Sprayer Fixed Boom Mount (S/N 3541+) Section 2 Booms

11 3-Point Sprayer Fixed Boom Mount (S/N 3541+) Section 2 Booms Ref. Part No. Part Description Comments D 3PT/3003PT SHIMS 18 GA D 3PT/3003PT SHIMS 24 GA D SWING PIVOT PIN FIXED MTG C PIN ROLL 5/16 X 1 3/4 PLT C NUT HEX FLANGE 5/16-18 PLT C HHCS 5/16-18X1 GR C WASHER FLAT 5/8 SAE PLT C HHCS 5/8-11X4 3/4 GR C HHCS 1/2-13X4 1/2 GR C NUT HEX FLANGE 3/8-16 PLT C NUT HEX FLANGE 1/2-13 GR G PLT C NUT HEX FLANGE LOCK 5/8-11 PLT C HHCS 1/2-13X4 GR D SPACER - HYD MANUAL FOLD ELEV H 3PT/3003PT UNIV MOUNT C WASHER FLAT 3/8 USS PLT C HHCS 3/8-16X1 1/2 GR H MANUAL FOLD LOCK CHAIN BASE C SP EYE 1/4-20X2 3/ C NUT HEX WHIZ 1/4-20 PLT C CHAIN LINK SNAP 1/4 PLT C HHCS 3/8-16X3 GR D CHAIN MANUAL TRANSPORT LOCK H WELDMENT BRKT WING FOLD LOCK H WELDMENT WING FOLD LOCK C PIN WIRE SNAP LOCK 3/8 X 3 1/ C NUT FLANGE LOCK 3/8-16 PLT V MANUAL FOLD LOCK SUBASSY Includes items 21 thru 27. Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 2-4

12 3-Point Sprayer Fold Bracket Assembly (S/N 3540-) Section 2 Booms

13 3-Point Sprayer Fold Bracket Assembly (S/N 3540-) Section 2 Booms Ref. Part No. Part Description Comments C U-BOLT 1/2-13 X 3 1/32 X H 3-PT MANUAL FOLD BOOM SUPPORT H FOLD BRACKET - MAN FOLD WELD H FOLD LATCH C NUT HEX FLANGE 1/2-13 GR G PLT C HHCS 1/2-13X4 GR C WASHER FLAT 1/2 SAE PLT D SPACER - HYD MANUAL FOLD ELEV C HHCS 3/8-16X1 GR C NUT HEX FLANGE 3/8-16 PLT C PIN WIRE SNAP LOCK 3/8 X 3 1/ C RHSNB 3/8-16X1 GR5 Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 2-6

14 Section 2 Booms 3-Point Sprayer Parking Stand Table of Contents Index

15 3-Point Sprayer Parking Stand Section 2 Booms Ref. Part No. Part Description Comments H CF/3P PARKING STAND FRONT C PIN WIRE SNAP LOCK 3/8 X 4 Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 2-8

16 Section 2 Booms 3-Point Carrier Assembly Table of Contents Index

17 3-Point Carrier Assembly Table of Contents Index Section 2 Booms Ref. Part No. Part Description Comments H MANUAL FOLD 3-PT CARRIER D BUSHING C PIN LYNCH 5/16 X 1 3/ H FOLD BRACKET - LEFT C AD 1MNPT X 3/4HB POLYPROP C AD 1FNPT X 1MCL POLYPROP C AD 1FNPT X 1FCL POLYPROP D COUPLER CLAMP C HHCS 5/16-18X3/4 GR C CLAMP WRM DRV #12 SS( ) C NUT HEX FLANGE 5/16-18 PLT C NUT HEX FLANGE 1/2-13 GR G PLT H COUPLER BRKT WELD C PIN HITCH 1 X 3 3/8 USABLE LG H FOLD BRACKET - MAN FOLD WELD C HHCS 3/8-16X1 GR H FOLD LATCH C RHSNB 3/8-16X1 GR C NUT HEX FLANGE 3/8-16 PLT C PIN WIRE SNAP LOCK 3/8 X 3 1/ H FOLD BRACKET - RIGHT C WASHER FLAT 1/2 SAE PLT C HHCS 1/2-13X4 GR D BUSHING - CAT 1 UPPER C PIN HITCH 1 1/4 X 3 USABLE LG S LOWER HITCH PIN ASSY Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision

18 3-Point Parking Stand Assembly Section 2 Booms

19 3-Point Parking Stand Assembly Section 2 Booms Ref. Part No. Part Description Comments H MF/3P PARKING STAND - BOT REAR C NUT HEX FLANGE 3/8-16 PLT C HHCS 3/8-16X2 1/2 GR H MF/3P PARKING STAND - TOP REAR C PIN WIRE SNAP LOCK 3/8 X 3 1/ H MF/3P PARKING STAND FRONT C PIN CLEVIS 1/2 X 5 PLATED C PIN HAIR COTTER.120 PLT Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision

20 Rear Fold Latch for Trailer Sprayers Section 2 Booms

21 Rear Fold Latch for Trailer Sprayers Section 2 Booms Ref. Part No. Part Description Comments H FOLD LATCH C RHSNB 3/8-16X1 GR C NUT HEX FLANGE 3/8-16 PLT H FOLD BRACKET - TS MOUNT RIGHT H FOLD BRACKET - TS MOUNT LEFT C NUT HEX FLANGE 1/2-13 GR G PLT C PIN WIRE SNAP LOCK 3/8 X 3 1/ C HHCS 3/8-16X1 GR H FOLD BRACKET - MAN FOLD WELD C HHCS 1/2-13X5 1/2 GR C WASHER FLAT 1/2 SAE PLT D SPACER - SA HYD ELEV MAN FOLD D SPACER - MF FOLD BRACKETS, TS Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision

22 Slow Moving Vehicle Decal Mounting Assembly Section 2 Booms

23 Slow Moving Vehicle Decal Mounting Assembly Section 2 Booms Ref. Part No. Part Description Comments C U-BOLT 5/16-18 X 2 X 2 1/ C NUT HEX FLANGE 5/16-18 PLT D BRACKET - SMV C DECAL SLOW MOVING-GALV. BACKED C HHCS 1/4-20X5/8 GR C WASHER LOCK SPRING 1/4 PLT C NUT HEX 1/4-20 PLT Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision

24 Section 3Section 3 Spray Kits Section 3 Spray Kits Table of Contents Index MF30 Nozzle Assembly 15" Spacing

25 MF30 Nozzle Assembly 15" Spacing Section 3 Spray Kits Ref. Part No. Part Description Comments C CLAMP WRM DRV #12 SS( ) R HOSE 3/4 ID 200PSI EPDM Order per foot C TEE 3/4HB POLYPROP C VALVE-DIAPHRAGM CHECK SINGLE Refer to page 4-1 for breakdown. Spraying Systems assembly interchangeable with Precision assembly (item 9) D CHECK BRACKET 2 X 1 1/4 TUBE D CHECK BRACKET 2 X 1 1/4 TUBE P C SFHMS 1/4-20 X 3/ C VALVE-DIAPHRAGM CHECK DOUBLE Refer to page 4-1 for breakdown. Spraying Systems assembly interchangeable with Precision assembly (item 10) C PRECISION VALVE - NOZZLE CHECK ELBOW Refer to page 4-3 for breakdown. Interchangeable with Spraying Systems assembly (item 4) C PRECISION VALVE - NOZZLE CHECK TEE Refer to page 4-3 for breakdown. Interchangeable with Spraying Systems assembly (item 8) C CABLE TIE.19X DIA 50LB V RECT TB SHANK CHECK BRKT ASSY Includes items 5, 6 & 7. Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 3-2

26 MF30 Nozzle Assembly 20" Spacing Section 3 Spray Kits

27 MF30 Nozzle Assembly 20" Spacing Section 3 Spray Kits Ref. Part No. Part Description Comments C CLAMP WRM DRV #12 SS( ) R HOSE 3/4 ID 200PSI EPDM Order per foot C TEE 3/4HB POLYPROP C VALVE-DIAPHRAGM CHECK SINGLE Refer to page 4-1 for breakdown. Spraying Systems assembly interchangeable with Precision assembly (item 9) D CHECK BRACKET 2 X 1 1/4 TUBE D CHECK BRACKET 2 X 1 1/4 TUBE P C SFHMS 1/4-20 X 3/ C VALVE-DIAPHRAGM CHECK DOUBLE Refer to page 4-1 for breakdown. Spraying Systems assembly interchangeable with Precision assembly (item 10) C VALVE - NOZZLE CHECK ELBOW Refer to page 4-3 for breakdown. Interchangeable with Spraying Systems assembly (item 4) C VALVE - NOZZLE CHECK TEE Refer to page 4-3 for breakdown. Interchangeable with Spraying Systems assembly (item 8) C CABLE TIE.19X DIA 50LB V RECT TB SHANK CHECK BRKT ASSY Includes items 5, 6 & 7. Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 3-4

28 MF30 Nozzle Assembly 30" Spacing Section 3 Spray Kits

29 MF30 Nozzle Assembly 30" Spacing Section 3 Spray Kits Ref. Part No. Part Description Comments C CLAMP WRM DRV #12 SS( ) R HOSE 3/4 ID 200PSI EPDM Order per foot C TEE 3/4HB POLYPROP C VALVE-DIAPHRAGM CHECK SINGLE Refer to page 4-1 for breakdown. Spraying Systems assembly interchangeable with Precision assembly (item 9) D CHECK BRACKET 2 X 1 1/4 TUBE D CHECK BRACKET 2 X 1 1/4 TUBE P C SFHMS 1/4-20 X 3/ C VALVE-DIAPHRAGM CHECK DOUBLE Refer to page 4-1 for breakdown. Spraying Systems assembly interchangeable with Precision assembly (item 10) C VALVE - NOZZLE CHECK ELBOW Refer to page 4-3 for breakdown. Interchangeable with Spraying Systems assembly (item 4) C VALVE - NOZZLE CHECK TEE Refer to page 4-3 for breakdown. Interchangeable with Spraying Systems assembly (item 8) C CABLE TIE.19X DIA 50LB V RECT TB SHANK CHECK BRKT ASSY Includes items 5, 6 & 7. Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 3-6

30 MF40 Nozzle Assembly 15" Spacing Section 3 Spray Kits

31 MF40 Nozzle Assembly 15" Spacing Section 3 Spray Kits Ref. Part No. Part Description Comments C CLAMP WRM DRV #12 SS( ) R HOSE 3/4 ID 200PSI EPDM Order per foot C TEE 3/4HB POLYPROP C VALVE-DIAPHRAGM CHECK SINGLE Refer to page 4-1 for breakdown. Spraying Systems assembly interchangeable with Precision assembly (item 9) D CHECK BRACKET 2 X 1 1/4 TUBE D CHECK BRACKET 2 X 1 1/4 TUBE P C SFHMS 1/4-20 X 3/ C VALVE-DIAPHRAGM CHECK DOUBLE Refer to page 4-1 for breakdown. Spraying Systems assembly interchangeable with Precision assembly (item 10) C VALVE - NOZZLE CHECK ELBOW Refer to page 4-3 for breakdown. Interchangeable with Spraying Systems assembly (item 4) C VALVE - NOZZLE CHECK TEE Refer to page 4-3 for breakdown. Interchangeable with Spraying Systems assembly (item 8) C CABLE TIE.19X DIA 50LB C EL 3/4HB POLYPROP V RECT TB SHANK CHECK BRKT ASSY Includes items 5, 6 & 7. Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 3-8

32 MF40 Nozzle Assembly 20" Spacing Section 3 Spray Kits

33 MF40 Nozzle Assembly 20" Spacing Section 3 Spray Kits Ref. Part No. Part Description Comments C CLAMP WRM DRV #12 SS( ) R HOSE 3/4 ID 200PSI EPDM Order per foot C TEE 3/4HB POLYPROP C VALVE-DIAPHRAGM CHECK SINGLE Refer to page 4-1 for breakdown. Spraying Systems assembly interchangeable with Precision assembly (item 9) D CHECK BRACKET 2 X 1 1/4 TUBE D CHECK BRACKET 2 X 1 1/4 TUBE P C SFHMS 1/4-20 X 3/ C VALVE-DIAPHRAGM CHECK DOUBLE Refer to page 4-1 for breakdown. Spraying Systems assembly interchangeable with Precision assembly (item 10) C VALVE - NOZZLE CHECK ELBOW Refer to page 4-3 for breakdown. Interchangeable with Spraying Systems assembly (item 4) C VALVE - NOZZLE CHECK TEE Refer to page 4-3 for breakdown. Interchangeable with Spraying Systems assembly (item 8) C CABLE TIE.19X DIA 50LB C EL 3/4HB POLYPROP V RECT TB SHANK CHECK BRKT ASSY Includes items 5, 6 & 7. Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision

34 MF40 Nozzle Assembly 30" Spacing Section 3 Spray Kits

35 MF40 Nozzle Assembly 30" Spacing Section 3 Spray Kits Ref. Part No. Part Description Comments C CLAMP WRM DRV #12 SS( ) R HOSE 3/4 ID 200PSI EPDM Order per foot C TEE 3/4HB POLYPROP C VALVE-DIAPHRAGM CHECK SINGLE Refer to page 4-1 for breakdown. Spraying Systems assembly interchangeable with Precision assembly (item 9) D CHECK BRACKET 2 X 1 1/4 TUBE D CHECK BRACKET 2 X 1 1/4 TUBE P C SFHMS 1/4-20 X 3/ C VALVE-DIAPHRAGM CHECK DOUBLE Refer to page 4-1 for breakdown. Spraying Systems assembly interchangeable with Precision assembly (item 10) C VALVE - NOZZLE CHECK ELBOW Refer to page 4-3 for breakdown. Interchangeable with Spraying Systems assembly (item 4) C VALVE - NOZZLE CHECK TEE Refer to page 4-3 for breakdown. Interchangeable with Spraying Systems assembly (item 8) C CABLE TIE.19X DIA 50LB V RECT TB SHANK CHECK BRKT ASSY Includes items 5, 6 & 7. Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision

36 MF45 Nozzle Assembly 15" Spacing Section 3 Spray Kits

37 MF45 Nozzle Assembly 15" Spacing Section 3 Spray Kits Ref. Part No. Part Description Comments C CLAMP WRM DRV #12 SS( ) R HOSE 3/4 ID 200PSI EPDM Order per foot C TEE 3/4HB POLYPROP C VALVE-DIAPHRAGM CHECK SINGLE Refer to page 4-1 for breakdown. Spraying Systems assembly interchangeable with Precision assembly (item 9) D CHECK BRACKET 2 X 1 1/4 TUBE D CHECK BRACKET 2 X 1 1/4 TUBE P C SFHMS 1/4-20 X 3/ C VALVE-DIAPHRAGM CHECK DOUBLE Refer to page 4-1 for breakdown. Spraying Systems assembly interchangeable with Precision assembly (item 10) C VALVE - NOZZLE CHECK ELBOW Refer to page 4-3 for breakdown. Interchangeable with Spraying Systems assembly (item 4) C VALVE - NOZZLE CHECK TEE Refer to page 4-3 for breakdown. Interchangeable with Spraying Systems assembly (item 8) C CABLE TIE.19X DIA 50LB V RECT TB SHANK CHECK BRKT ASSY Includes items 5, 6 & 7. Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision

38 MF45 Nozzle Assembly 20" Spacing Section 3 Spray Kits

39 MF45 Nozzle Assembly 20" Spacing Section 3 Spray Kits Ref. Part No. Part Description Comments C CLAMP WRM DRV #12 SS( ) R HOSE 3/4 ID 200PSI EPDM Order per foot C TEE 3/4HB POLYPROP C VALVE-DIAPHRAGM CHECK SINGLE Refer to page 4-1 for breakdown. Spraying Systems assembly interchangeable with Precision assembly (item 9) D CHECK BRACKET 2 X 1 1/4 TUBE D CHECK BRACKET 2 X 1 1/4 TUBE P C SFHMS 1/4-20 X 3/ C VALVE-DIAPHRAGM CHECK DOUBLE Refer to page 4-1 for breakdown. Spraying Systems assembly interchangeable with Precision assembly (item 10) C VALVE - NOZZLE CHECK ELBOW Refer to page 4-3 for breakdown. Interchangeable with Spraying Systems assembly (item 4) C VALVE - NOZZLE CHECK TEE Refer to page 4-3 for breakdown. Interchangeable with Spraying Systems assembly (item 8) C CABLE TIE.19X DIA 50LB C EL 3/4HB POLYPROP V RECT TB SHANK CHECK BRKT ASSY Includes items 5, 6 & 7. Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision

40 MF45 Nozzle Assembly 30" Spacing Section 3 Spray Kits

41 MF45 Nozzle Assembly 30" Spacing Section 3 Spray Kits Ref. Part No. Part Description Comments C CLAMP WRM DRV #12 SS( ) R HOSE 3/4 ID 200PSI EPDM Order per foot C TEE 3/4HB POLYPROP C VALVE-DIAPHRAGM CHECK SINGLE Refer to page 4-1 for breakdown. Spraying Systems assembly interchangeable with Precision assembly (item 9) D CHECK BRACKET 2 X 1 1/4 TUBE D CHECK BRACKET 2 X 1 1/4 TUBE P C SFHMS 1/4-20 X 3/ C VALVE-DIAPHRAGM CHECK DOUBLE Refer to page 4-1 for breakdown. Spraying Systems assembly interchangeable with Precision assembly (item 10) C VALVE - NOZZLE CHECK ELBOW Refer to page 4-3 for breakdown. Interchangeable with Spraying Systems assembly (item 4) C VALVE - NOZZLE CHECK TEE Refer to page 4-3 for breakdown. Interchangeable with Spraying Systems assembly (item 8) C CABLE TIE.19X DIA 50LB V RECT TB SHANK CHECK BRKT ASSY Includes items 5, 6 & 7. Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision

42 Section 4Section 4 Valves Section 4 Valves Table of Contents Index Spraying Systems Check Valve Assembly

43 Spraying Systems Check Valve Assembly Section 4 Valves Ref. Part No. Part Description Comments NYB SPRAYING SYS CHECK VALVE CAP 2. CP21953-VI SSC DIAPH VITON Standard 2 CP21953-EPR SPRAYING SYS EPDM DIAPHRAGM Optional C VALVE-DIAPHRAGM CHECK SINGLE C VALVE-DIAPHRAGM CHECK DOUBLE Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 4-2

44 Precision Check Valve Assembly Section 4 Valves

45 Precision Check Valve Assembly Section 4 Valves Ref. Part No. Part Description Comments PRECISION CHECK VALVE FLY NUT PRECISION RED NOZZLE CHK VALVE PRECISION VITON DIAPHRAGM CHK C VALVE-NOZZLE CHECK TEE C VALVE-NOZZLE CHECK ELBOW Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 4-4

46 Section 4 Valves Nozzle Assembly Table of Contents Index

47 Nozzle Assembly Table of Contents Index Section 4 Valves Ref. Part No. Part Description Comments C STRAINER #8079-PP-50 MESH C GASKET NOZZLE CAP CP19438-EPR C NOZZLE FLAT FAN XR8001VS C NOZZLE FLAT FAN XR80015VS C NOZZLE FLAT FAN XR8002VS C NOZZLE FLAT FAN XR8003VS C NOZZLE FLAT FAN XR8004VS C NOZZLE FLAT FAN XR8005VS C NOZZLE FLAT FAN XR8006VS C NOZZLE FLAT FAN XR8008VS C NOZZLE FLAT FAN XR11001VS C NOZZLE FLAT FAN XR110015VS C NOZZLE FLAT FAN XR11002VS C NOZZLE FLAT FAN XR11003VS C NOZZLE FLAT FAN XR11004VS C NOZZLE FLAT FAN XR11005VS C NOZZLE FLAT FAN XR11006VS C NOZZLE FLAT FAN XR11008VS C CAP-NOZZLE & GSKT # NYR A XR8001VS TEEJET NOZZLE ASSY A XR80015VS TEEJET NOZZLE ASSY A XR8002VS TEEJET NOZZLE ASSY A XR8003VS TEEJET NOZZLE ASSY A XR8004VS TEEJET NOZZLE ASSY A XR8005VS TEEJET NOZZLE ASSY A XR8006VS TEEJET NOZZLE ASSY A XR8008VS TEEJET NOZZLE ASSY A XR11001VS TEEJET NOZZLE ASSY A XR110015VS TEEJET NOZZLE ASSY A XR11002VS TEEJET NOZZLE ASSY A XR11003VS TEEJET NOZZLE ASSY A XR11004VS TEEJET NOZZLE ASSY A XR11005VS TEEJET NOZZLE ASSY A XR11006VS TEEJET NOZZLE ASSY A XR11008VS TEEJET NOZZLE ASSY C LOCTITE PST PIPE SEALANT D 20 DEG NOZZLE ADAPTER W/CAP V MC NOZZLE ASSY V MC NOZZLE ASSY V MC NOZZLE ASSY V MC NOZZLE ASSY V MC NOZZLE ASSY V MC NOZZLE ASSY V MC NOZZLE ASSY V MC NOZZLE ASSY V MC NOZZLE ASSY A MC NOZZLE KIT DEG A MC NOZZLE KIT DEG A MC NOZZLE KIT DEG A MC NOZZLE KIT DEG A MC NOZZLE KIT DEG A MC NOZZLE KIT DEG A MC NOZZLE KIT DEG A MC NOZZLE KIT DEG A MC NOZZLE KIT DEG C NOZZLE CLEANING BRUSH Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 4-6

48 Section 5Section 5 Decals Section 5 Decals Decal Placement Table of Contents Index /12/2003

49 Decal Placement Table of Contents Index Section 5 Decals Ref. Part No. Part Description Comments C DECAL DANGER POWER LINES C DECAL GREAT PLAINS BOOMS C DECAL RED NARROW REFLECTOR C DECAL LEVEL FLOAT PIN C DECAL LEVEL FLOAT PIN STORAGE C DECAL SLOW MOVING-GALV. BACKED A MAN FOLD SAFETY DECAL PACKAGE Includes items 1 thru 6. Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 6/12/

50 Section 6Section 6 Options Section 6 Options Calibration Kit Table of Contents Index /12/2003

51 Calibration Kit Table of Contents Index Section 6 Options Ref. Part No. Part Description Comments C CALIBRATION CONTAINER C DECAL AMBER REFLECTOR H SPRAYER STRING MARKER WELDMENT C DECAL CALIBRATION STAKES C TWISTED NYLON TWINE 350 FT C AS NOZZLE TIP CALCULATOR Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 6-2